APG-1410 TYPICAL PROPERTIES GET THE API ADVANTAGE... CHARACTERISTICS APPLICATION TEST DATA

Transcription

1 TYPICAL PROPERTIES GET THE API ADVANTAGE... Appearance: Light yellow/amber liquid Solids: 13% Solvent: >85% Water Solubility: Disperses readily in water is a water based fluorochemical solution that will impart a high degree of oil and grease resistance to paper or fiberboard. may be applied by method of size press, spray or pad. will also impart a sizing effect to paper or fiberboard. CHARACTERISTICS has no effect on the hand, color, air permeability or strength of paper. may be safely applied to paper and fiberboard designed for use as food packaging or wrapping. conforms to FDA regulation Title 21 Food and Drugs, Part as components of paperboard in contact with aqueous and fatty foods under conditions of use b through h in paragraph (c) of section , table 2. APPLICATION Use soft water (between 60 ppm to 75 ppm total hardness) or water softened with Versene 100 (Dow Chemical Company) following the manufacturer s recommendations. The concentration of Versene 100 will vary with hardness, but generally 0.1% Versene 100 is sufficient. Water that has been softened to less than 50 ppm total hardness will create an excess amount of foam if the dilution is agitated. TEST DATA PET FOOD TEST FOR FC TREATED PAPER Objective: Measure the oil resistance of fluorochemical treated paper after exposure to commercial pet food. Advanced Polymer, Inc. 400 Paterson Plank Road Carlstadt, NJ Phone: (201) Fax: (201)

2 GET THE API ADVANTAGE... Conditions: Brown kraft paper treated with 0.3% (solids) fluorochemical. Dried / cured at 225 F for 3 minutes Dimensions of FC treated paper = 4 x 4 Dimensions of backing sheet = 4 x 4 (grid divided into 100 equal squares) Aluminum ring = 0.5 inch high, 2.75 inches inside diameter Weight = 560 grams, 2.75 inches diameter Hard rubber roller = grams, 1-3/4 inch wide Weight of ground Iams cat food (minimum fat content = 21%) sample = 45 grams (approximately 80 ml) Oven temperature = 140 F Time = 24 hours Test Procedure: The test samples were cut into 4 x 4 equal squares folded in half and creased using a weighted rubber roller. The samples were unfolded and the rubber roller was used again on the opened crease. Blotting paper was placed onto a metal plate. A backing sheet divided into 100 equal squares was placed underneath the 4 x 4 test sample. An aluminum ring was placed on top of each test sample; ground pet food was then placed into the aluminum rings. A 560-gram weight was placed on top of the pet food sample & then placed in a preheated oven at 140 o F for 24 hrs. The test paper and grid sheet were removed from the oven and separated. The number of stained boxes on the grid sheet were counted and reported as percent stained. Results: Product % Staining* 28% Competitive Sample A 64% Competitive Sample B 87% * % Staining = number of squares discolored on the grid sheet. PACKAGING is available in 8 oz. samples and 441-lb drums. Advanced Polymer, Inc. 400 Paterson Plank Road Carlstadt, NJ Tel: (201) Fax: (201) I want to know more! technical@advpolymer.com You may also be interested in... The information set forth herein is furnished free of charge and based on technical data that Advanced Polymer, Inc. believes to be reliable. It is intended for use by persons having technical skill at their own risk. Because conditions of use are outside our control, we make no warranties, express or implied, and assure no liability in connection with any use of this information. Nothing herein is to be taken as license to operate under or a recommendation to infringe any patents. Revised August 28, 2009

3 Section I Product Identity Product Name: Chemical Name/Family: Perfluoralkyl phosphate solution CAS Registry: Mixture 24 Hour Emergency Number Hour Chemtrec Number All ingredients are listed in EPA's TSCA list of chemical substances Section II Hazardous Components/Composition Information CHEMICAL : Water CAS #: USOS: TWA: STEL: PERCENT: >85 CHEMICAL : Perfluoroalkyl phosphate CAS #: Proprietary USOS: TWA: STEL: PERCENT: 13 Section III Physical and Chemical Properties Boiling Point ND Specific Gravity (H2O=1) 1.05 Vapor Pressure ND Vapor Density (Air=1) ND Percent Volatile By Weight >85 Evaporation Rate (BuAc=1) ND Solubility in Water Dispersible Appearance and Odor Light yellow/amber solution. Section IV Fire and Explosion Hazard Data Flash Point (Method Used) Flammable Limits in Air (% By Volume) Extinguishing Media Special Fire Fighting Procedures: Unusual Fire and Explosion Hazard >200 F (Closed Cup) Use extinguishing media appropriate for surrounding fire. A self-contained breathing apparatus and protective clothing must be worn in fighting fires involving chemicals Burning may produce toxic vapors, including HF and carbon monoxide Section V Reactivity Data Stability Conditions to Avoid Incompatibilities Hazardous Decomposition or By Products Hazardous Polymerization Stable Avoid elevated temperatures (>110 F). Keep from freezing. Oxidizers, metal chlorides and acids May produce CO, HF May not occur

4 Section VI Health hazard Data Primary Routes of Entry Inhalation: Yes Dermal: Yes Ingestion: Yes Acute Health hazard Chronic Health Hazard Carcinogenicity NTP: No IARC Monograph: No OSHA Regulated: No Signs and Symptoms of Exposure: Skin Contact Eye Contact Ingestion Inhalation May be harmful. Causes irritation. May be harmful if swallowed. May be harmful if inhaled. Medical Condition Generally Aggravated by Exposure No information is available Emergency First Aid Procedures Eyes Skin Ingestion Inhalation Immediately flush eyes with plenty of water for at least 15 minutes. Seek medical attention. Immediately wash skin with soap and water. Do not induce vomiting. Immediately give 2 glasses of water. Never give anything by mouth to an unconscious person. Call a physician. Immediately remove to fresh air. If not breathing give artificial respiration. If breathing is difficult, give oxygen. Please note: Symptoms may be delayed; prompt medical attention may be required. Call a physician. Section VII Precautions for Safe Handling and Use Steps to be Taken in Case the Material is Released or Spilled: Soak up with sawdust, sand, oil dry or other absorbent material. Waste Disposal Method: Dispose of according to State and Local regulations. Section VIII Special Precautions Precautions to be Taken in Handling and Storage: Store at temperatures between 40 o F and 95 o F. Store in a tightly closed container. Store in a well ventilated area. Store away from oxidizing agents, sources of heat, direct sunlight or rain. No smoking in area of storage. Use soft water (between 60 ppm to 75 ppm total hardness when preparing treating solution.) *** Agitate contents of container before using *** MSDS Page 2

5 Section IX Control Measures Respiratory Protection Wear respirator where vaporizing occurs. Ventilation Local exhaust Recommended where vaporizing occurs. Eye Protection Protective Gloves Protective Clothing Other Protective Equipment Other Precautions Section X SARA Title III Mechanical Special Other SECTION 313 SUPPLIER NOTIFICATION General ventilation is recommended. None None Safety glasses should be worn Impervious gloves should be worn Apron, boots or coveralls as necessary to prevent skin contact Eye was equipment Wash hands thoroughly after use. This product contains the following toxic chemicals subject to the reporting requirements of SECTION 331 of the EMERGENCY PLANNING AND COMMUNIUTY RIGHT-TO-KNOW ACT OF 1986 and of 40 CFR 371 CAS # Chemical Name Percent by Weight THIS INFORMATION MUST BE INCLUDED IN ALL MSDSs THAT ARE COPIED AND DISTRIBUTED FOR THIS MATERIAL Section XI Transportation Information SHIPPING INFORMATION is not regulated by DOT. Hazard Ratings Health 1 Flammability 0 Reactivity 0 Date Prepared... March 17, 2005 Prepared By... API Date Revised... November 30, 2009 Revised By... API THE INFORMATION AND RECOMMENDATIONS HEREIN, ARE TO THE BEST OF OUR KNOWLEDGE, TRUE AND ACCURATE. NO WARRANTY, EXPRESS OR IMPLIED, IS MADE OR INTENDED. MSDS Page 3

6 TO THE CUSTOMERS OF ADVANCED POLYMER, INC. All statements, technical information and recommendations contained herein are based on tests we believe to be reliable, but the accuracy or completeness thereof is not guaranteed, and the following is made in lieu of all warranties, express or implied: Seller's and manufacturer's only obligation shall be to replace such quantity of the product proved to be defective. Neither seller nor manufacturer shall be liable for any injury, loss of damage, direct, or consequential arising out of the use of or the inability to use the product. Before using, user shall determine the suitability of the product for his intended use. The user assumes all risk and liability whatsoever in connection therewith. No statement or recommendation contained herein shall have any force or effect unless in an agreement signed by officers of seller and manufacturer. Since the manufacturer of the product described in this technical data sheet has no means of controlling the final use of the product by the consumer for the user, it is the responsibility of the immediate purchaser and any intermediate seller or sellers to inform the user of the purposes for which the product may be fit and suitable and of the properties of the product, including the precautionary measures which must be taken in order to ensure the safety of the user and of other third persons and property. No statement made herein shall be taken as an authorization or inducement to practice any patented invention without appropriate license. MSDS Page 4