Freestanding Appliqué Sleigh # / 11 Designs

Transcription

1 # / 11 Designs HG123_48 Reindeer ase Connector 2.10 X 1.22 in X mm 3,800 St. S HG124_48 Reindeer Middle Connector 2.08 X 2.69 in X mm 8,039 St. HG125_48 Reindeer 1 Side 3.88 X 4.35 in X mm 18,822 St. HG126_48 Reindeer 1 Side 3.88 X 4.35 in X mm 18,801 St. HG127_48 Reindeer 2 Side 3.81 X 4.31 in X mm 17,392 St. HG128_48 Reindeer 2 Side 3.81 X 4.31 in X mm 17,409 St. HG129_48 Reindeer 3 Side 3.36 X 4.30 in X mm 15,901 St. HG130_48 Reindeer 3 Side 3.36 X 4.30 in X mm 15,579 St. HG131_48 Sleigh Floor 3.89 X 6.66 in X mm 24,286 St. L HG132_48 Sleigh Side 4.60 X 4.03 in X mm 21,884 St. HG133_48 Sleight Side 4.60 X 4.03 in X mm 21,887 St. HG134_48 lank Square 33,935 St. HG135_48 Square 35,507 St. HG136_48 C Square 35,164 St. HG137_48 E Square 35,744 St.

2 HG123_48 Reindeer ase Connector 1. Cover Stitches Cover Stitch Linework Freestanding ppliqué Sleigh # / 11 Designs Listings below indicate color sample, stitching order and suggested thread color number. Most numbers indicate Isacord thread. Colors beginning with refer to YLI Fine Metallics, 7 refer to Yenmet Metallic, 8 refer to YLI Variations Variegated Thread and 9 refer to Isacord Multicolor Variegated. HG124_48 Reindeer Middle Connector 3. Inner Designs Nodes Cover Stitches HG125_48 Reindeer 1 Side HG126_48 Reindeer 1 Side HG127_48 Reindeer 2 Side HG128_48 Reindeer 2 Side HG129_48 Reindeer 3 Side HG130_48 Reindeer 3 Side HG131_48 Sleigh Floor 3. Inner Designs Nodes Cover Sticthes HG132_48 Sleigh Side 5. Inner Design Cover Stitches Cover Stitch Linework HG133_48 Sleight Side 5. Inner Design Cover Stitches Cover Stitch Linework HG134_48 lank Square HG135_48 Square HG136_48 C Square HG137_48 E Square

3 Freestanding ppliqué Guidelines General Freestanding ppliqué Guidelines Supplies: Embroidery Thread: Use the same embroidery thread in the bobbin as the needle. Needles: Use an Organ 80/12 Titanium needle for extended needle life. Stabilizer: Use water-soluble stabilizer or film water-soluble stabilizer. General ppliqué Instructions 1. Hoop two layers of water-soluble stabilizer. 2. ttach the hoop to the machine and select the design of your choice. 3. Stitch the Placement Stitch. Photo 1 4. Place a piece of appliqué fabric over the Placement Stitch so that it is completely covered. 5. Stitch the Cut Line & Tackdown Stitch. 6. Carefully cut away the excess applique fabric. Photo 2 7. Stitch the remainder of the design and repeat for any remaining pieces. Photo 3 8. Remove the hoop from the machine and the design from the hoop. 9. Trim excess stabilizer from the design. 10. Rinse away remaining stabilizer and allow it to dry. Handy Hints For 3D ppliqué Projects: dhere 2 layers of heavy weight stabilizer to the back of fabrics with temporary adhesive spray EFORE hooping or placing down for tackdown and cut in place. This gives fabric a more rigid structure. pair of tweezers, hemostats, stiletto or a tiny crochet hook can be extremely helpful when inserting the buttonettes into the eyelets. (See Diagram 1 for explanation of buttonette and eyelet.) Insert the tip of the tweezers, hemostats or crochet hook into the eyelet, grasp the buttonette and pull through the eyelet. Or a stiletto could be used to push the buttonette through the eyelet. uttonette Diagram 1 Eyelet ppliqué 1 2 3

4 Instructions REINDEER & SLEIGH Reindeer Instructions: Follow the GENERL FREESTNDING PPLIQUÉ GUIDELINES to stitch the six reindeer, three appliqué connectors, and the three white diamond shaped connector pieces. Glitz individual pieces as desired. Insert the five buttonettes on one side of the rectangular appliqué connector into the five eyelets on the reindeer, from the inside of the reindeer to the outside. Insert the five buttonettes on the other side of the same connector piece into the five eyelets of the matching reindeer piece from the inside of the reindeer to the outside. Insert the buttonette of the diamond shape connector into the eyelet at the lower center of the reindeer piece from the inside out. Insert the opposite buttonette on the connector into the eyelet at the base of the second reindeer. Repeat with the remaining two sets of reindeer.

5 Instructions SLEIGH Follow the GENERL FREESTNDING PPLIQUÉ GUIDELINES to stitch the two side pieces and one center appliqué piece for sleigh. The connecting piece will button into the two side pieces of the sleigh. To connect all the reindeer and the sleigh, feed ribbon (approximately 1 ½ yards width 3/8 wide) from the sleigh into the side of each reindeer. Feed across the front reindeer and back to the sleigh like reins.