ACS5000 Reader Wiring Guide
|
|
- Stanley Tracy Moore
- 7 years ago
- Views:
Transcription
1 ACS5000 Reader Wiring Guide 10/16/2014 2
2 Table of Contents Proximity Readers Manufacturer Model(s) Page HID 5355 ProxPro 5 HID 6005 Proxpoint, 5395 ThinlineII, 5365 Mini-Prox 6 FARPOINTE DATA P-300, P Smart Card Readers Manufacturer Model(s) Page HID 6100 R10, 6140 R15, 6110 R30, 6120 R40, 6130 RK40, 6150 R FARPOINTE DATA Delta3, Delta5, Delta Multi-Technology Readers Manufacturer Model(s) Page HID 6145 RP15, 6125 RP40, 6136 RPK Wireless Receivers Manufacturer Model(s) Page CHAMBERLAIN Centex Wireless Receiver 13 FARPOINTE DATA Ranger Wireless Receiver 14 3
3 Grounding the Shields Shielded reader wire is required for all Brivo ACS5000 installations. The shield for each reader run should be tied to the grounding lug located in the lower left corner of the ACS5000 panel chassis. The chassis should then be grounded to a reliable earth ground. An electrical ground is usually not acceptable for Brivo installations, therefore it should not be considered for the panel ground. The diagram below shows a typical earth ground. Reader The reader shield should never be connected at the reader Reader Grounding Bus To ensure that the reader shield does not make contact with board level components or other wires, either use a jacketed 18AWG cable between the drain or shield and the grounding lug, or use heat shrink in order to isolate the drain or shield.! NEVER CONNECT YOUR GROUND WHILE THE PANEL EQUIPMENT IS ENERGIZED. DISCONNECT ALL BATTERIES AND REMOVE AC POWER FROM THE PANEL PRIOR TO CONNECTING GROUNDS. 4
4 Preface Brivo Systems conforms to the SIA Access Control Standard Protocol for the 26-bit Wiegand Reader Interface. Due to varieties of implementation in Wiegand, Brivo chooses to validate the reader in the marketplace for compatibility and the reliability between two systems. In the event that you are attempting to purchase or install a reader to be used with a Brivo ACS5000 Panel, it is recommended that you first review the Reader Wiring Guide for known compatible readers. Any reader that is not currently covered under the ACS5000 Reader Wiring Guide can be tested and added to the guide. Instructions on having a reader tested are contained at the end of this document. Legacy readers may be covered under previous versions of the ACS5000 Reader Wiring Guide. Legacy readers have been removed from the current ACS5000 Reader Wiring Guide due to a lack of hardware to validate operation. If a legacy reader is to be used, please contact Technical Support for access to a previous version that may include the legacy reader. The readers that have been validated, yet omitted from this guide are: AWID Sentinel-Prox KP-6840 AWID Sentinel-Prox LR-911 AWID Sentinel-Prox MM-6800 AWID Sentinel-Prox MR-1824 AWID Sentinel-Prox SP-6820 AWID Sentinel-Prox SR-2400 Northern BR-7 Barcode Reader Bioscrypt V Smart, A Bioscrypt VeriProx, V, H If a previously supported reader is not included in this guide and not listed above, that reader is no longer valid for use with the ACS5000. Please contact Brivo Technical Support should you have any questions. 5
5 HID 5355 ProxPro The HID ProxPro readers are connected at a terminal strip inside the reader housing. The wiring diagram shows the expected wire colors for the connection between the ProxPro and the ACS5000. Please note any changes in the wiring schema to make sure that the correct terminals are interconnected. 22/6 500 Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green DATA 0 Data 0 / Wiegand data0 White DATA 1 Data 1 / Wiegand data1 Black GROUND Reader Ground gnd Yellow BEEPER Buzzer / Optional buzz Red DC+ +12VDC 12vdc Orange GRN LED Green LED Control grn led Brown RED LED Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 6 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
6 HID 6005 Proxpoint, 5395 ThinlineII, 5365 Mini-Prox The pigtail shown below is standard for most of the HID 6005, 5395 and 5365 model readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Wire Gauge Distance Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Brown LED Control grn led Orange NOT USED ***** N/A Blue NOT USED ***** N/A Violet NOT USED ***** N/A Please refer to the HID Installation Manual associated with the reader to be installed for additional information. 7
7 Proximity Readers Farpointe Pyramid Readers The pigtail shown below is standard for most of the Farpointe Data Pyramid and Delta series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. 22/8 or 18/8 may be required if the buzzer is required in conjunction with the Dual Line LED control option. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Blue Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown(2) Red LED Control red led Yellow NOT USED ***** N/A Single Line Control: The Brown Wire connects to the Green LED Control and the Orange Wire is not connected. Dual Line Control: The Brown Wire connects to the Red LED Control and the Orange Wire connects to the Green LED control. Please refer to the Farpointe Data Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the Farpointe Data reader. 8
8 HID R10, R15, R30, R40, RK40 iclass Readers with 18 Pigtail The pigtail shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown Red LED Control red led Blue NOT USED ***** N/A Violet NOT USED ***** N/A Be sure to cover the unused wires. Grounding the Hold Wire can cause unreliable operation. LED Operation The LED will follow the configuration upon a card being read. During Valid Access or Rex, the ACS5000 will control the Green LED. During an Unlock Schedule, the LED will alternate Red/Green. During Credential Validation Check, The panel LED will alternate Red/Amber if available on the reader. Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader. 9
9 HID R10, R15, R30, R40, RK40 iclass Readers with Terminal The terminal shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green P2-3 Data 0 / Wiegand data0 White P2-4 Data 1 / Wiegand data1 Black P1-3 Reader Ground gnd Yellow P1-1 Buzzer / Optional buzz Red P VDC 12vdc Orange P1-2 Green LED Control grn led Brown P1-6 Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 10 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
10 Proximity Readers Farpointe Delta Readers The pigtail shown below is standard for most of the Farpointe Data Pyramid and Delta series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. 22/8 or 18/8 may be required if the Buzzer is required in conjunction with the Dual Line LED control option. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Blue Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown(2) Red LED Control red led Yellow NOT USED ***** N/A Single Line Control: The Brown wire connects to the Green LED control and the Orange wire is not connected. Dual Line Control: The Brown wire connects to the Red LED control and the Orange wire connects to the Green LED control. Please refer to the Farpointe Data Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the Farpointe Data reader. 11
11 HID RP15, RP40, RPK40 iclass Readers with 18 Pigtail The pigtail shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Yellow Buzzer / Optional buzz Red +12VDC 12vdc Orange Green LED Control grn led Brown Red LED Control red led Blue NOT USED ***** N/A Violet NOT USED ***** N/A Be sure to cover the unused wires. Grounding the hold wire can cause unreliable operation. LED Operation The LED will follow the configuration upon a card being read. During Valid Access or Rex, the ACS5000 will control the Green LED. During an Unlock Schedule, the LED will alternate Red/Green. During Credential Validation Check, The panel LED will alternate Red/Amber if available on the reader. Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader. 12
12 HID RP15, RP40, RPK40 iclass Readers with Terminal The terminal shown below is standard for most of the HID iclass and multiclass series readers. The connection between the reader and the panel must be made using proper 22/6 or 18/6 shielded cable. The shield should be connected at the panel using the reader ground port as the landing for the shield or drain wire. Be careful to not allow the shield or drain wire to make contact with the components on the board or other wires in the chassis. Be sure to trim and isolate all unused wiring. Recommended Wire Installer Reader Wire Reader Location Function Panel Location Green P2-3 Data 0 / Wiegand data0 White P2-4 Data 1 / Wiegand data1 Black P1-3 Reader Ground gnd Yellow P1-1 Buzzer / Optional buzz Red P VDC 12vdc Orange P1-2 Green LED Control grn led Brown P1-6 Red LED Control red led Blue N/A Not Used ***** N/A Violet N/A Not Used ***** N/A 13 Please refer to the HID Installation Manual associated with the reader to be installed for additional information and warnings in regards to proper installation of the HID reader.
13 Wireless Receivers Chamberlain Liftmaster Wireless Receiver The configuration shown below is designed to connect one output on the Chamberlain Centex Wireless Receiver to the ACS5000. Most Centex transmitters have the ability to transmit a 26-bit credential to the receiver as well as to be used as a proximity FOB for traditional proximity readers. Please refer to the Chamberlain datasheets and installation guides regarding the proper transmitter/receiver combination. Reader Wire Function Panel Location Green Data 0 / Wiegand data0 White Data 1 / Wiegand data1 Black Reader Ground gnd Red +12VDC 12vdc Please refer to the Chamberlain Liftmaster Centex Receiver Installation Manual for instructions on proper installation. 14
14 Wireless Receivers Farpointe Ranger Wireless Receiver The configuration shown below is designed to connect one output on the Chamberlain Centex Wireless Receiver to the ACS5000. Most Centex transmitters have the ability to transmit a 26-bit credential to the receiver as well as to be used as a proximity FOB for traditional Proximity readers. Please refer to the Chamberlain datasheets and installation guides regarding the proper transmitter/receiver combination. Farpointe Ranger Term. Function Panel Location Green Wir ADO/BDO Data 0 / Wiegand data0 White AD1/BD1 Data 1 / Wiegand data1 Black GND Reader Ground gnd Red +12V +12VDC 12vdc Orange BDO/ADO Green LED Control grn led Brown BD1/AD1 Red LED Control red led Please refer to the Installation manual associated with the Farpointe Data Ranger Wireless Receiver for proper installation and configuration. 15
15 Reader Evaluation Request Form Brivo Systems will evaluate and qualify a reader for installation with the Brivo ACS5000 Panel. All we ask is that you provide us with a reader and the credentials required for operation. Evaluation of a reader may take up to two weeks to complete. Any reader that is sent to Brivo must be in like new condition and free of any defects. This service is open to all Brivo Authorized Dealers. Reader manufacturers are requested to contact Brivo s Product Management Team for evaluation. Company Name: Name: Address: City: State / Province: Zip / Postal Code: Phone Number: Address: Signature: Requirements: Reader must operate at 500 ft. Reader will be used in an elevator Reader requires power Reader must operate with specific credentials (include credentials with reader) Type of Reader: Prox 125Khz SC 13.56Mhz RF Multi-Tech Barcode / Magstripe Comments: This form may be ed to customercare@brivo.com. A Technical Support Representative will follow up with a case number. When the reader is to be shipped to Brivo for evaluation, please be sure to include the case number and a copy of this form with the reader. If cards are to be tested with use on the reader, please send approximately 10 cards in non-sequential order. 16
VARIO PROX CARD READER INSTALLATION MANUAL
VARIO PROX CARD READER INSTALLATION MANUAL TABLE OF CONTENTS 1.0 INTRODUCTION...2 1.1 Legend...3 1.2 Terminology...4 2.0 MOUNTING...5 3.0 WIEGAND CONNECTION...6 4.0 AUX BUTTON INPUT...7 5.0 INSTALLER PROGRAMMING...8
More informationGV- RK1352 Card Reader
GV- RK1352 Card Reader The GV-RK1352 is a card reader with keypad, designed to recognize PIN codes, identification cards or both. Featured with the Wiegand and RS-485 outputs, the unit can be connected
More informationModel 201 Wiegand Touchpad Reader Installation Guide
Model 201 Wiegand Touchpad Reader Installation Guide P/N 460353001C 15AUG11 2011 UTC Fire & Security. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without
More informationPROXIMITY CARD READERS C-10, C-20, C60, C70
Installation Manual PROXIMITY CARD READERS C-10, C-20, C60, C70 VERSION 1.0 CONTENTS 1. General information................................. 3 2. Technical data......................... 4 3. Connection
More informationDIVISION 28 ELECTRONIC SAFETY AND SECURITY SECTION 28 13 00 SECURITY AND ACCESS CONTROL SYSTEM
DIVISION 28 ELECTRONIC SAFETY AND SECURITY PART 1 GENERAL 1.01 DESCRIPTION A. Division 28 Contractor shall extend a complete Matrix Systems Access Control System as shown on the Drawings and as specified
More informationAccess control using the COM1000 and Wiegand Protocol Card Readers
Access control using the COM1000 and Wiegand Protocol Card Readers Introduction The use of modern access control systems in government and private buildings has become commonplace. These systems enable
More informationEMBEDDED ACCESS CONTROL Hardware Installation Guide
EMBEDDED ACCESS CONTROL Hardware Installation Guide Lenel goentry Hardware Installation Guide, product version 1.00. This guide is item number DOC- ENHW-ENU, revision 1.003, April 2009 Copyright 2009 Lenel
More informationHSG Engineering Tech Bulletin
Specifications subject to change OCT 2013; Rev. 1.3 HSG Engineering Tech Bulletin Recommended RS-485 Wiring for NetAXS-4/NetAXS-123 Loops Overview This document provides the recommended RS-485 wiring for
More informationIMMS-CCC. IMMS-CCC Hardwire Central Interface. Installation Instructions
IMMS-CCC IMMS-CCC Hardwire Central Interface Installation Instructions TABLE OF CONTENTS... Choose a Location... 1 Connections... 2 Operations... 3 Software Configuration... 4 Troubleshooting... 5 Loopback
More informationAC-115 Compact Networked Single Door Controller. Installation and User Manual
AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction...5 1.1 Key Features... 6 1.2 Technical Specifications... 7 2.
More information[FAQ] Troubleshooting Access Control Issues
[FAQ] Troubleshooting Access Control Issues Article ID: GV4-14-06-16-t Release Date: 06/16/2014 Applied to GV-ASManager GV-AS Controller GV-Reader Summary When you encounter problems with GV-ASManager,
More informationACCESS CONTROL SYSTEM
ACCESS CONTROL SYSTEM Flexible, Expandable, Economical. The i-pass system comprises of the i-pass controller built with state of the art technology to provide reader access for up to 16 doors and 32 elevator
More informationAR-721U/721K/661U User s Guide
AR-72U/72K/66U User s Guide Feb. 6, 2004 Table of Contents Page. Main Feature --------------------------------- 3 2. AR-72U Installation --------------------------------- 4 2. Steps ---------------------------------
More informationPRO Series. Card Readers, Cards and Tags
PRO Series Card Readers, Cards and Tags All Proximity Card Readers: Offer high reliability, consistent read range characteristics, and low power consumption in a single, easy-to-install package. Are sealed
More informationNMEA 0183 INSTALLATION AND OPERATING GUIDELINES
NMEA 0183 INSTALLATION AND OPERATING GUIDELINES Revised July 2010 8.1.3 Documentation The following documentation shall be provided to the owner for each interfaced system and shall be kept on file by
More informationHardware Installation Guide
Integrated security for an IP-connected world Hardware Installation Guide June 2012 S2 Security Corporation One Speen Street Suite 300 Framingham, MA 01701 S2 Chat Support: www.s2pronto.com/prontosupport
More informationDraper Low Voltage, Remote Control, Serial and Network Wiring Guide
Draper Low Voltage, Remote Control, Serial and Network Wiring Guide Copyright 2007 Draper Inc. Form LV-RC-Serial-Network_Wiring07 Print ed in U.S.A. Draper Low Voltage, Remote Control, Serial and Network
More informationInstruction Sheet ACS-101. General Description. Specifications. Amplified Broadband UHF Combiner-Splitter. Overall. Antenna Splitter.
ACS-101 Amplified Broadband UHF Combiner-Splitter General Description The ACS-101 (Antenna Combiner Splitter 10 to 1) is an amplified and filtered broadband splitter-combiner. It allows up to 10 base stations
More informationProxPro Wiegand/Clock-and-Data
9292 Jeronimo Road Irvine, CA 92618-1905 ProxPro Wiegand/Clock-and-Data 5355/8A INSTALLATION GUIDE 5355A-900, Rev N.1 February 22, 2007 Part No. 5355-900, Rev N.1 ProxPro Installation Guide Contents 1
More informationEQUIPMENT SPECIFICATIONS
EQUIPMENT SPECIFICATIONS IC-1600 Intelligent Controller The IC-1600 Intelligent Controller is a fully intelligent panel that has a complete database on board. It operates in conjunction with the Access
More informationINSTALLATION MANUAL XM3 Reader
INSTALLATION MANUAL XM3 Reader Conditions Transactions, deliveries et cetera will be according to the general terms of delivery as deposited at the Chamber of Commerce at Meppel, The Netherlands. Registration
More information1 x TS0861 Magnetic Swipe Card Reader. 1 x Installation Guide (this document).
g GE Interlogix TS0861 Magnetic Swipe Card Reader Installation Guide Installation Kit 1 x TS0861 Magnetic Swipe Card Reader. 1 x Installation Guide (this document). 2 x 3x6mm post button head screws that
More informationINSTALLATION/PROGRAMMING INSTRUCTIONS E4KP ENTRYCHECK
Security Door Controls 3580 Willow Lane, Westlake Village, CA 91361-4921 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION/PROGRAMMING INSTRUCTIONS E4KP
More informationAD-Series. Selection Guide
AD-Series Selection Guide The first step in our design process: Listening. We wanted to know exactly what you needed in a security solution. So we asked. We asked hundreds of questions and received thousands
More informationAllegion AD-300 Installation Application Note. 1.0 Hardware Requirements. 2.0 Software/Licensing Requirements
Allegion Schlage AD-300 networked, hardwired locks can be integrated seamlessly with the Doors.NET software when used with the NXT-MSC (Mercury-Powered controllers). You can connect and communicate with
More informatione-ask electronic Access Security Keyless-entry
e-ask electronic Access Security Keyless-entry e-fob Keyless-entry entry System Full-Function Function Installation Manual FCC ID: TV2EFOB1 (UM20 ~ 22793-02) Table of Contents Introduction... 1 e-fob Operation
More informationKeypad / Reader Configuration and Programming Guide
Keypad / Reader Configuration and Programming Guide DATE: 4 SEPTEMBER 2012 DOCUMENT PERTAINS TO: KEYPAD /READER CONFIGURATION AND PROGRAMMING GUIDE REVISION: B Continental 2012 Keypad / Reader Configuration
More informationINSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930
INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features..................................
More informationHM-W536 Install Guide
HM-W536 Install Guide 9/13/2013 IMPORTANT SAFETY INSTRUCTIONS Warning - When using electrical devices, basic safety precautions should be followed to reduce the risk of fire, electrical shock or injury.
More informationWIRELESS STATUS MONITOR
INSTALLATION INSTRUCTIONS WIRELESS STATUS MONITOR (WSM or AUWSM) The most current version of this document is available for download at: http://www.ir-swa.com P/N: M053-032-D Schlage 245 W. Roosevelt Road,
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationipdatatel Wi-Fi BAT Installation and Configuration Guide
ipdatatel Wi-Fi BAT Installation and Configuration Guide This guide is for customers who want install the ipdatatel equipment before their programming appointment. This guide covers installing the IPD-Wifi-BAT
More informationUsing the ievo fingerprint reader with Net2
Using the ievo fingerprint reader with How does it work? The ievo system stores the encoded fingerprint information within each reader. Once registered on the enrolment reader, the fingerprint data is
More informationHONEYWELL COMMERCIAL FIRE/BURG PANEL UL LISTING REQUIREMENTS (Compiled from VistaFBPT Installation Instructions 800-09617V1 Rev A 11/12)
HONEYWELL COMMERCIAL FIRE/BURG PANEL UL LISTING REQUIREMENTS (Compiled from VistaFBPT Installation Instructions 800-09617V1 Rev A 11/12) UL864 (Commercial Fire) Compliance General Requirements The VISTA-128FBPT/VISTA250FBPT
More informationSWITCH! DESCRIPTION. ENVIRONMENTAL SPECIFICATIONS Operating Temperature: 0 C to +40 C SPECIFICATION SHEET:
SWITCH The Budderfly lighting switch is a Decora style, plug-and-play replacement for your existing building switches. Installing a Budderfly adapter transforms your building s existing wiring into the
More informationUser Manual. Before installation and use, please read the user manual carefully.
Sebury Technology Co., Ltd. Address: 5/F, Building 8, Xinwu Industrial Park, Xili, Nanshan District, Shenzhen, China. Tel: +86-755-88856 Fax: +86-755-888565 P.C.: 58055 www.sebury.com.cn User Manual Before
More informationSolar Home System. User Manual. AEH-SHS01-10W2L Solar Home System 2 Lamps
Solar Home System User Manual AEHSHS0110W2L Solar Home System 2 Lamps All rights reserved Specifications subject to change without prior notice 2 Dear Customer, Thank you for purchasing Schneider Electric
More informationINSTALLATION INSTRUCTIONS
LIGHTING CONTROL PANELS 4 AND 8 RELAYS INSTALLATION INSTRUCTIONS INSTALLATION OVERVIEW The installation instructions contained in this document are provided as a guide for proper and reliable installation.
More informationMCR1900 Media Converter 19-Slot Chassis
MCR1900 Media Converter 19-Slot Chassis Installation Guide Part #5500304-11 Copyright Statement This document must not be reproduced in any way whatsoever, either printed or electronically, without the
More informationLMU-5000. Hardware and Installation Guide
LMU-5000 Hardware and Installation Guide Plan The Installation Verify Power, Ground and Ignition. Be sure to check each source (power, ground and ignition) to ensure that the proper signaling exists. This
More informationUSB Card Reader Interface User Manual
USB Card Reader Interface User Manual SB Research 2009-2012 The USB Reader Interface family: Concept: The USB Card Reader Interface allows access control card readers to be connected to a PC, in order
More informationFN2001-A1 Network module (SAFEDLINK) Mounting Installation
FN00-A Network module (SAFEDLINK) Mounting Installation A6V050_f_en_-- 05-0-6 Building Technologies Division Legal notice Legal notice Technical specifications and availability subject to change without
More informationOPERATING INSTRUCTIONS Model ST-888 DTMF ANI/ENI Display Decoder
P R O D U C T G R O U P OPERATING INSTRUCTIONS Model ST-888 DTMF ANI/ENI Display Decoder Manual # 600-0901 November 30, 1999 Rev. D - 99068 DESCRIPTION The ST-888 Mobilecall Display Decoder is a desktop
More informationALPHA Meter Installation Information
October 006 IL4-400Q ALPHA Meter Installation Information General This instructional leaflet contains general installation instructions for the following single phase and polyphase watthour meters: socket-connected
More informationThree-Phase Electric Power Distribution for Computer Data Centers
Three-hase Electric ower Distribution for Computer Data Centers WHITE AER E901 Geist January 008 Summary This paper will describe the characteristics of three-phase power and outline the advantages of
More informationHG600/HG800. Hydro-Power Unit. Installation and Operation Guide
HG600/HG800 Hydro-Power Unit Installation and Operation Guide Copyright 04 HydroSpin, All rights reserved. The data contained in this document is proprietary to HydroSpin. It is disclosed to the receiving
More informationUniversal Vehicle Power Supply 9007AX01. Installation Instructions
Universal Vehicle Power Supply 9007AX01 Installation Instructions Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained in
More informationMobile Device Power Monitor Battery Connection Quick Start Guide
Mobile Device Power Monitor Battery Connection Quick Start Guide Distributed By: Monsoon Solutions, Inc. www.msoon.com Introduction The Power Tool software and the Mobile Device Power Monitor hardware
More informationPK-01. Standalone door control module. SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00
Standalone door control module PK-01 Firmware version 1.00 pk-01_en 06/12 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu WARNINGS Read carefully
More informationStructureScan HD Module. Installation Guide ENGLISH. www.bandg.com www.simrad-yachting.com www.lowrance.com
StructureScan HD Module Installation Guide ENGLISH www.bandg.com www.simrad-yachting.com www.lowrance.com Disclaimer As Navico is continuously improving this product, we retain the right to make changes
More informationDT105X / PB105 Series
DT105 / Series Cash Drawer Trigger & Printer Beeper User's Manual TM951031-05 Contents Information... 1 Technical And Operational Description... 3 Connections Load Test Specifications......... 5 7 8 Communication
More informationSSW-iLM Keypad. Wire Harness Configuration. Note: This product is designed to be installed and serviced by security and lock industry professionals
SSW-iLM Keypad Note: This product is designed to be installed and serviced by security and lock industry professionals Specifications Case dimensions: 6 1/2 L x 1 3/4 W x 1 1/8 D Electrical: 5-12VDC Only
More informationSchneider Automation Modbus Plus Network Installing Clustered Node Devices 31000939 00 Version 2.0
Schneider Automation Modbus Plus Network Installing Clustered Node Devices 3000939 00 Version.0 Modbus Plus devices must be installed as specified in a network layout plan, showing each device s mounting
More informationBUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
More informationVersion Date Author Description 1.00 19.07.2010 Jpo First version 1.01 21.12.2010 Jpo FET output descriptions made clearer 1.02 04.02.
+3 # Version Date Author Description 1.00 19.07.2010 Jpo First version 1.01 21.12.2010 Jpo FET output descriptions made clearer 1.02 04.02.2011 Jpo Reset button added 1. Purpose of this user manual...
More informationWIRELESS READER INTERFACE - INDOOR
INSTALLATION INSTRUCTIONS WIRELESS READER INTERFACE - INDOOR (WRI-IN-12VDC or AUWRI-IN-12VDC) The most current version of this document is available for download at: http://www.ir-swa.com P/N: M053-014-C
More informationIP Card Reader Interface User Manual
IP Card Reader Interface User Manual SB Research 2009-2011 The IP Reader Interface family: Concept: The IP Card Reader Interface allows access control card readers to be connected to a network device,
More informationInstallation manual. Version 1.1. www.videx-security.com
Installation manual Version 1.1 www.videx-security.com 2 Table of Contents MANUAL INTRODUCTION... 4 SYSTEM INTRODUCTION... 4 SYSTEM COMPONENTS... 5 CONTROLS... 6 3.5A 13.8Vdc PSU... 6 CONTROL PCB... 6
More informationArista 40G Cabling and Transceivers: Q&A
Arista 40G Cabling and Transceivers: Q&A 40G Cabling Technical Q&A Document 40Gigabit Cables and Transceivers Q. What 40G cables and transceivers are available from Arista? A. Arista supports a full range
More informationMobile Satellite Solutions. A WiWorld Partner SATELLITE TV ANTENNA CONTROLLER RFM-1000/1100 TECHNICAL MANUAL STOW SEARCH
Mobile Satellite Solutions A WiWorld Partner SATELLITE TV ANTENNA CONTROLLER RFM-1000/1100 TECHNICAL MANUAL SEARCH STOW Ver. 1 June 2012 WARNING Make all electrical and coax connections from the controller
More informationKnowledge Base Article. Integrating ISONAS Access Control System with TagMaster LR-series RFID Readers
Knowledge Base Article Integrating ISONAS Access Control System with TagMaster LR-series RFID Readers Copyright 2009-2012, ISONAS Security Systems All rights reserved Table of Contents 1: INTRODUCTION...
More informationDCP Fan Controller. Version 01/2009. The engineer s choice
Version 01/2009 The engineer s choice Index Page 1. Introduction... 3 2. Technical specification... 4 3. Connection diagrams... 9 4. Configuration... 10 5. Compatible ebm-papst Fan List... 11 2 1. Introduction
More informationGV-AS/EV Controller. User s Manual
GV-AS/EV Controller User s Manual Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. AS100.110.120.210.400.410.810-EV48-A
More informationFlexPoint T1/E1 Copper to Fiber Line Driver
BLACK BOX NETWORK SERVICES MT660A-MM MT661A-SM MT660A-MM-E MT661A-SM-E FlexPoint T1/E1 Copper to Fiber Line Driver CUSTOMER Order toll-free in the U.S.: Call 877-877-BBOX SUPPORT (outside U.S. call 724-746-5500)
More informationPower Supply and Cabling Options. SmartTrak 100/101/140
Power Supply and Cabling Options SmartTrak 00/0/40 2 Power Supply and Cabling Options SmartTrak 00/0/40 Table of Contents Power Supplies... Communication Cables... Accessory Options... Appendix A Communication
More informationUser Manual. BARKODES BİLGİSAYAR SİSTEMLERİ ARF Panel
1 User Manual Barkodes Bilgisayar Sistemleri Bilgi İletişim ve Yazılım Tic. Ltd. Şti. Adres: Altay Çeşme Mahallesi Sanayi Sokak No:8 Demirli Sitesi B Blok Maltepe-İstanbul/Turkey Tel: + 90 (216) 442 20
More informationRLH 2 Wire Digital Phone Fiber Link Card System
RLH Industries, Inc. The leader in rugged fiber optic technology. USER GUIDE! Unconditional Lifetime Warranty U-008 2014C-0924 RLH 2 Wire Digital Phone Fiber Link Card System CARD INSTALLATION INFORMATION
More informationRGB Light Panel Applications. RGB LED Light Panel FEATURES & BENEFITS SPECIFICATION SHEET
RGB LED Light Panel E346146 E325925 FEATURES & BENEFITS AVAILABLE IN CUSTOM SIZES & SHAPES CAN BE USED IN FRAMELESS DESIGNS 3D V-CUTTING TECHNOLOGY MULTI-COLOR OPTION HIGH BRIGHTNESS (2,000-10,000 LUX)
More informationS2 Security Corporation NetBox. Installation Guide
S2 Security Corporation NetBox Installation Guide Version 2.0 S2 Security Corporation 6 Abbott Road Wellesley, MA 02481 www.s2sys.com UL Listing UL 294 listing for the S2 NetBox is pending. Note to Installers
More information1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
More informationRUST ELECTRONICS LTD. Remote Switching Unit RCU-O4
RUST ELECTRONICS LTD Remote Switching Unit RCU-O4 MAINS REMOTE SWITCHING UNIT RCU-O4 The RCU-O4 is a radio remote controlled switching unit that will allow the remote operation of any appropriate electrical
More informationManual. Simrad StructureScan LSS-1 Sonar Module. English
Manual Simrad StructureScan LSS-1 Sonar Module English www.simrad-yachting.com A brand by Navico - Leader in Marine Electronics Disclaimer As Navico is continuously improving this product, we retain the
More informationCoolWave r 2 Phase Control Board and Cable Replacement Kits
Instruction Sheet P/N 1102452A CoolWave r 2 Phase Control Board and Cable Replacement Kits Two kits are available to replace the CoolWave 2 phase control board: S S Phase Control Board and Cable Kit (required
More informationPART 1 - INTRODUCTION...
Table of Contents PART 1 - INTRODUCTION... 3 1.1 General... 3 1.2 Sensor Features... 3 1.3 Sensor Specifications (CDE-45P)... 4 Figure 1-1 CDE-45P Sensor Dimensions (standard, convertible style)... 4 PART
More informationDORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS
Features: INSTALLATION Install in accordance with NFPA 70. DORMA MODEL PS-406BB POWER SUPPLY INSTALLATION INSTRUCTIONS Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short
More informationWxGoos-1 Climate Monitor Installation Instructions Page 1. Connections. Setting an IP Address
Instructions Page 1 Connections The WxGoos-1 is a self-contained web server and requires 6vdc of power at 300ma. A center-positive 2.1 mm plug is used. There are five ports: 1. 10/100 Ethernet RJ-45 receptacle
More informationBL-DBK150A DUAL BATTERY 12v 150 AMP SMART SYSTEM
BL-DBK150A DUAL BATTERY 12v 150 AMP SMART SYSTEM Waterproof and Shockproof Easy DIY Dual Battery System BL-DBK150A Supplied Parts List Parts List 1 x 12v 150Amp Electronic Dual Battery Smart Controller
More informationHID Global Product Catalog
HID Global Product Catalog ACCESS SECURE IDENTITY An ASSA ABLOY Group brand THANK YOU for your continued support of HID Global access control products. This catalog contains a wealth of product information
More informationmaxon motor maxon motor control EPOS Positioning Controller Cable Starting Set Edition June 2006 part number 302287 Positioning Controller
control EPOS Positioning Controller Cable Starting Set Edition June 2006 24/1 part number 302287 Positioning Controller Documentation Cable Starting Set 1 Table of contents 1 Table of contents... 2 2 Table
More informationLocoNet, the Digitrax Difference
LocoNet, the Digitrax Difference LocoNet is Digitrax's method of communication between LocoNet compatible devices on a model railroad layout. LocoNet Compatible devices are designed to work together on
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationC24-CAMANL Video Server/Encoder
C24-CAMANL Video Server/Encoder User s Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Overview... 1 Physical Details - Video Server... 2 Package Contents... 3 CHAPTER 2 BASIC SETUP... 4 System Requirements...
More informationT-100-R Installation Guide
T-100-R Installation Guide Table of Contents Page 2 Overview T-100-R Z-Wave Thermostat 3-4 Installation HVAC System Setup 6 Installer Settings Menu Items 7-9 Installer Settings Summary 10-11 Wiring Standard
More informationSPECIAL NOTICE. All references to NAT product part numbers (and associated images) are equivalent to AEM product part numbers.
SPECIAL NOTICE This product is now licensed to Anodyne Electronics Manufacturing (AEM) from Northern Airborne Technology (NAT). AEM is responsible for all matters related to this product, including sales,
More informationCM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems
CM705B - Universal Expander Module CM707B - Plug On Zone Expander Security Systems EN Security System CM705B CM705B - Universal Expander Module The CM705B universal expander provides a cost effective way
More informationAccess Professional Edition Selection Guide
Access Professional Edition Selection Guide 2 Contents Contents 3 System overview 3 Wiegand based hardware 4 RS485 Bus reader 5 Selection Guide The Seven Steps to your Access System 6 Step 1: Choose Base
More informationINTELLIGENT CONTROL MODULE SA-2000-II HARDWARE MANUAL. Access Technologies International, Inc.
SA-2000-II HARDWARE MANUAL Access Technologies International, Inc. 1 Table of Contents 1. Introduction 3 2. Features 3 3. Specification 4 4. Identifying Supplied Parts 4 5. Panel Description 5 6. Connection
More informationbba - Balboa Bluetooth Audio (AMP) Installation & User Guide
bba - Balboa Bluetooth Audio (AMP) Installation & User Guide Bluetooth Integration CONNECT YOUR SMART DEVICE TO YOUR HOT TUB With Bluetooth connection you can now play all your favorite songs directly
More informationZlinx Wireless I/O. Peer-to-Peer and Modbus I/O B&B ELECTRONICS PRODUCT INFORMATION
Modular, Customizable Wire Replacement 128 / 256 Bit AES Encryption Software Selectable RF Transmit Power Software Selectable Over-the-air Data Rate Modbus ASCII /RTU Compatible Wide Operating Temperature
More informationPERF10 Rubidium Atomic Clock
Owner s Manual Audio Stanford Research Systems Revision 1.0 February, 2011 2 Certification Stanford Research Systems certifies that this product met its published specifications at the time of shipment.
More informationDSX Master Communications
DSX Access Systems, Inc. PC to Master Controller - Direct Connect Communications DSX Master Communications Communications between the Comm Server PC and the Master Controller can take several forms which
More informationOEM-1300 Universal Data Converter
OEM-1300 Universal Data Converter Installation User Manual Rev B Thank You! Congratulations on the purchase of your OEM-1300 device(s). RF IDeas hopes you enjoy using the readers as much as we enjoyed
More informationL-1 Fingerprint Reader Solutions. V-Flex 4G
L- Fingerprint Reader Solutions V-Flex 4G 4G Biometric Performance Redefined with a Flexible and Powerful Device to Secure any Size Premises Advanced Features Large Template Storage Capacity (0,000 in
More informationManual for connection of load cells to junction box and weighing indicators 2014-01-10 Ver 1
Manual for connection of load cells to junction box and weighing indicators 2014-01-10 Ver 1 Junction Box YZ-J4 From junction box one cable, min 0,25mm² to indicator => => * Important! Turn all potentiometers
More informationSecurity & Control Cables
Security & Control Cables Our multi-conductor cables are manufactured in a wide variety of gage sizes, shielding configurations and jacketing materials including plenum, riser and general purpose. Applications
More informationAir-cooled Generator Battery Charger Installation Guidelines
Air-cooled Generator Battery Charger Installation Guidelines Table of Contents Table of Contents...Inside Front Cover Section 1 General Information... IFC 1.1 Introduction...IFC 1.2 Battery Charger Compatibility...
More informationTS2 VRack. User and Installation Manual
TS2 VRack User and Installation Manual B 4934252 Rev. A October 2007 TS-2 VRack All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical,
More informationPanduit 28 AWG Patch Cords Installation Guideline
Panduit 28 AWG Installation Guideline Introduction Panduit is a leading supplier of Structured Cabling Systems and Unified Physical Infrastructure. Panduit solutions enable the physical infrastructure
More informationTECHNICAL DATASHEET #TD1404AX PWM CONTROLLED SOLENOID DRIVER
TECHNICAL DATASHEET #TD1404AX PWM CONTROLLED SOLENOID DRIVER (PWM Input, 1.2A or 2A Output, Metal Box or PCB) PCB Board - P/N: PWMC-PCB-2A, PWMC-PCB-1.2A Packaged Driver (metal box with 1.5 m (5 ft.) cable)
More informationUSB 2.0 4-Port Extender Kit
USB 2.0 4-Port Extender Kit 500072 MuxLab Inc. 2014 94-000760-A / SE-000760-A Table of Contents 1. Introduction... 2 2. Features... 2 3. Specifications... 2 4. Package Contents... 3 5. Physical Diagram...
More information