CERTIFICATE OF APPROVAL No CF 5304 FIRE GLASS UK LIMITED

Transcription

1 CERTIFICATE OF APPROVAL No CF This is to certify that, in accordance with TS General Requirements for Certification of Fire Protection Products The undermentioned products of Unit, Spartan Industrial Estate, Brickhouse Lane, West Bromwich, West Midlands B7 DH Tel: 8 Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT Pyrobelite 7, Pyrobelite 9EG, Pyrobelite, Pyrobelite & EG, Pyrobel & EG, Pyrobel 7N & 7N EG, Pyrobel 9H, Pyrobel & EG, Pyrobel 8H, Pyrobel & EG, Pyrobel N & N EG, Pyrobel - IGU, Fire Resisting TECHNICAL SCHEDULE TS Fire Resistant, Glazing Systems and Materials Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Chairman - Management Council Page of 77

2 PYROBELITE AND PYROBEL FIRE RESISTING GLASS This Certificate of Approval relates to the fire resistance of AGC Flat UK Limited Laminated glass products when used in the following applications, as defined in BS 7: Part : 987 subject to the undermentioned conditions. Specification Application Fire Resistance Performance (mins) Page No. Integrity Insulation Pyrobelite 7 & 9 EG Timber doorsets (hardwood beads) - 7 Pyrobelite 7 & 9 EG Timber doorsets (MDF beads) - 8 Pyrobelite 7 & 9 EG (IGU s) Composite doorsets - 9 Pyrobelite 7 & 9 EG Timber doorsets - Pyrobelite 7 & 9 EG Timber screens - Pyrobelite 7 & 9 EG (IGU s) Timber screens - Pyrobelite 7 & 9 EG (IGU s) Steel doorsets - Pyrobelite 7 & 9 EG Steel screens - Pyrobelite 9EG Timber Screens - Pyrobelite Timber doorsets (hardwood beads) - 7 Pyrobelite Timber doorsets (MDF beads) - 8 Pyrobelite Steel screens - 9 Pyrobelite (IGU s) Steel screens - Pyrobelite Timber screens - Pyrobelite Timber doorsets - Pyrobelite Timber doorsets - Pyrobelite Timber screens - Pyrobelite & EG Steel screens - Pyrobelite Steel screens - Pyrobel & EG Timber doorsets 7 Pyrobel & EG Timber doorsets 8 Pyrobel & EG Timber doorsets 9 Pyrobel & EG Timber doorsets Pyrobel & EG Timber screens Pyrobel & EG Timber screens Pyrobel & EG (IGU s) Timber screens Pyrobel & EG Visionline Butt Jointed in timber Pyrobel & EG Visionline Butt Jointed in steel Pyrobel & EG Visionline Butt Jointed in aluminium Visionline Corner Joint Butt Jointed Corner Joint 8 Pyrobel & EG (IGU s) Timber screens 9 Pyrobel & EG (IGU s) Steel screens Pyrobel & (IGU s) Steel doorsets Pyrobel Steel screens - Pyrobel Steel screens Pyrobel & EG Steel screens Pyrobel & EG (IGU s) Aluminium screens Pyrobel & EG (IGU s) Aluminium screens Pyrobel Aluminium screens 7 Page of 77 Signed

3 PYROBELITE AND PYROBEL FIRE RESISTING GLASS Specification Application Fire Resistance Performance Page (mins) No. Integrity Insulation Pyrobel 7N & 7N EG Timber screens 8 Pyrobel 7N & 7N EG Steel screens 9 Pyrobel 7N & 7N EG Steel screens Pyrobel & EG Timber doorsets Pyrobel & EG Timber screens (hardwood) Pyrobel & EG Timber screens (softwood) Pyrobel & EG (IGU s) Timber screens Pyrobel & EG Steel screens Pyrobel & EG Steel doorsets Pyrobel & EG (IGU s) Steel doorsets 7 Pyrobel & EG (IGU s) Steel screens 8 Pyrobel & EG Aluminium screens 9 Pyrobel & EG Aluminium screens Pyrobel & EG (IGU s) Aluminium screens Pyrobel & EG Visionline Butt Jointed in timber Pyrobel & EG Visionline Butt Jointed in steel Pyrobel & EG Visionline Butt Jointed in aluminium Visionline Corner Joint Butt Jointed Corner Joint Pyrobel & EG & IGU Steel screens Pyrobel & EG & IGU Steel doors Pyrobel N & N EG Steel screens 9 Pyrobel N & N EG Visionline Butt Jointed in steel 7 Pyrobel -IGU Steel Screens 7 Pyrobel 9H Horizontal steel screens 7 Pyrobel 8H Horizontal steel screens 7 Pyrobelite 7/ & Pyrobel / Glazing bars Page of 77 Signed

4 The glass is approved in the following nominal thicknesses: Specification Thickness Fire Resistance Performance (mins) Integrity Insulation Pyrobelite mm ±.9mm / Pyrobelite 9EG. mm ±.mm Pyrobelite mm ± mm Pyrobelite. mm ± mm / Pyrobelite EG. mm ± mm Pyrobel 7. mm ± mm / Pyrobel EG. mm ±. mm / Pyrobel 7N 7.8 mm ±.mm / Pyrobel 7N EG. mm ±.8 mm / Pyrobel. mm ± mm Pyrobel EG. mm ± mm Pyrobel mm ±.mm 9 9 Pyrobel EG.7 mm ±.8 mm 9 9 Pyrobel N.7 mm ± mm Pyrobel N EG. mm ± mm Pyrobel - IGU 9. mm ± mm Pyrobel 9H 9. mm ±. mm Pyrobel 8H 8. mm ± mm Page of 77 Signed

5 PYROBELITE AND PYROBEL FIRE RESISTING GLASS This product is approved on the basis of: a) Initial type testing b) A design appraisal against TS c) Certification of quality management system to BS EN ISO 9: 8 d) Inspection and surveillance of factory production control e) Audit Testing in accordance with TS This Certificate of Approval must be read in conjunction with CERTIFIRE Technical Schedule TS, Fire Resistant, Glazing Systems and Materials. General Requirements Where the glass is installed in a timber or steel framed screen, the orientation of the screen shall be no more than ±º from the vertical. There is no restriction to the direction of exposure for the glass. Orientation may, however, be restricted by the requirements of a non-symmetrical framing system. The edge cover to each pane shall be no less than mm minimum. For external application, or in the case of direct solar radiation on the glazing, Pyrobel is available as external grade, with a UV filter. A minimum. mm laminated glass must be used as the external pane for IGU s incorporating internal grade Pyrobelite/Pyrobel. Minimum spacer width in IGU s should be mm. Surface of glass may be lightly sandblasted to a maximum depth of mm. Manifestation films may be applied to the fully insulated glass variants. IGU s may include either aluminium or steel spacer bars and may utilise hot melt butyl edge sealant. Warm edge spacers referenced Edgetech Superspacer, Swissspacer V, Thermobar and Thermix TXN may also be utilised. IGU s comprising Pyrobelite/Pyrobel glass may incorporate blinds integrally fitted within the IGU. The fitment of such blinds should not necessitate the removal of any framing or beading material and should be operated via a remote system (i.e. operating system may be magnetic). AGC Flat UK Limited should be consulted prior to specifying integral blinds to ensure acceptability. For timber framed glazing systems timber beads may be square. Pyrobelite and Pyrobel Matelux options are approved throughout the scope. Ash timber species (minimum density kg/m ) is acceptable in all applications for up to and including minute applications. Where foam tape or ceramic fibre is specified as a glazing tape, Interdens intumescent strip may be used as an alternative. Page of 77 Signed

6 PYROBELITE AND PYROBEL FIRE RESISTING GLASS Shapes It is also acceptable to include Pyrobelite and Pyrobel in shaped apertures, i.e. circles, ovals, arches, quadrants, etc (examples detailed below). within timber door leaves or screens (subject to limitations in the framing systems). For rectilinear apertures angles between adjoining perimeter beads should not be less than. Where shaped apertures are included, only finger jointed glazing beads are acceptable. Maximum linear dimensions or areas as approved should not be exceeded. Page of 77 Signed

7 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in timber based doorsets for periods of minutes integrity (hardwood beads) The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 7 8 Pyrobelite 7 or 9 EG Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam tape mm high by 9. mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible / hardwood setting blocks mm thick hardwood aperture liner 7 mm long steel screws or pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite 7 and 9 EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Figure. Maximum Permitted Dimensions Page 7 of 77 Signed Width

8 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in timber based doorsets for periods of minutes integrity (MDF Beads) The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 7 8 Pyrobelite 7 or 9 EG Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam tape mm high by 9. mm wide (including mm high by mm wide bolection with o chamfer or square) MDF glazing beads, minimum density kg/m Non-combustible / hardwood setting blocks mm thick MDF or hardwood aperture liner 7 mm long steel pins (.8 mm diameter) at mm centres ( o to glass) starting at mm in from corners 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite 7 and 9 EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Figure. Maximum Permitted Dimensions Maximum Area. m 7 Page 8 of 77 Signed

9 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 (IGU s) in composite doorsets for periods of minutes integrity Approval of Pyrobelite 7 or 9EG IGU s is approved, at the dimensions given in Figure below, for use in certain specific designs of composite doorset. There is no limit regarding glass orientation. AGC Limited should be contacted for further information on suitable applications. 979 Figure. Maximum Permitted Maximum Area. m Dimensions Width Page 9 of 77 Signed

10 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in timber based doorsets for periods of minutes integrity The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 7 8 Pyrobelite 7 Neutral silicone capping mm wide by mm thick 'Fire and Acoustic closed cell foam tape mm high by mm wide (including mm high by mm wide bolection with o chamfer or square) MDF or hardwood glazing beads Non-combustible / hardwood setting blocks mm thick by wide Therm-A-Line aperture liner 7 mm long,.8 mm diameter steel pins or screws ( mm long) at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite 7 glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area. m Figure. Maximum Permitted Dimensions Width Page of 77 Signed

11 7 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in timber framed screens for periods of minutes integrity The glass shall be glazed utilising the following basic specification: Pyrobelite 7 or 9 EG Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or mm wide by mm thick closed cell foam tape mm wide by mm high (with o chamfer or square) hardwood or softwood glazing beads, minimum density 7 kg/m Non-combustible setting blocks 8 mm long steel screws at 7 mm centres or 8 mm long steel pins at mm centres ( o to glass) 7 7 mm by mm (minimum) hardwood or softwood perimeter frame, minimum density 7 kg/m. 7 mm by mm (minimum) hardwood or softwood transoms/mullions, minimum density 7 kg/m. This Certificate of Approval relates to the sizes of Pyrobelite 7 and 9 EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. May be utilised in multipaned screen systems with shared transoms and mullions. 9 Maximum Area.9m 87 Figure. Maximum Permitted Dimensions 7 Page of 77 Signed Width Maximum Area.9 m Maximum Area. m

12 PYROBELITE FIRE RESISTING GLASS Insulating Units (IGU s) including Pyrobelite 7 in timber framed screens for periods of minutes integrity The IGU shall be glazed utilising one of the following specifications: 7 IGU comprising Pyrobelite 7 or Pyrobelite 9 EG glass, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)* Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or mm wide by mm thick closed cell foam tape mm wide by mm high (with o chamfer or square) hardwood glazing beads, minimum density 7 kg/m Non-combustible setting blocks mm long steel screws at 7 mm centres or mm long steel pins at mm centres ( o to glass) 7 8 mm by mm (minimum) hardwood frame, minimum density 7 kg/m * A minimum.8 mm laminated glass must be used as the external pane for IGU s incorporating internal grade Pyrobelite 7. This Certificate of Approval relates to the sizes of IGU s including Pyrobelite 7 or 9 EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area. m Figure. Maximum Permitted Dimensions 7 Page of 77 Signed Width

13 PYROBELITE FIRE RESISTING GLASS Insulating Units (IGU s) including Pyrobelite 7 in Steel Doorsets for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel profiled doorleaf framing system.. IGU comprising Pyrobelite 7 or Pyrobelite 9 EG glass, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*. Neutral silicone capping. Ceramic fibre based glazing tape. Neoprene seal. Steel bead. Steel section, stile and rail 7. Steel section, jamb and head Lining board to partition 9. Framework to partition. Steel screw * A minimum.8 mm laminated glass must be used as the external pane for IGU s incorporating internal grade Pyrobelite 7. The steel profiled door framing system shall have test evidence (such as RP Technik Hermetic ) or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. If the proposed doorset is to be used in double-leaf configuration, the test or assessment evidence should be applicable to double-leaf configurations. Likewise, if the proposed doorset is to be used in the unlatched configuration, the available evidence should be applicable to unlatched doorsets. When used to glaze CERTIFIRE approved doorsets which have smaller apertures than allowed in this certificate, the aperture sizes specified in the doorset certificate shall take precedence. This Certificate of Approval relates to the sizes of Pyrobelite 7 and 9 EG glass shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 8 Maximum Area.7 m Figure 7. Maximum Permitted Dimensions 98 Page of 77 Signed 8 87 Width

14 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system Pyrobelite 7 or 9 EG Neutral silicone capping mm wide by - mm thick ceramic fibre glazing tape Non-combustible/hardwood setting blocks Steel plate mm by mm Steel section mm by mm by mm 7 Steel angle mm by mm by mm 8 mm long steel screws at mm centres An example of a tested framing system is detailed above. Alternative framing systems shall have test evidence, such as Jansen Economy or Forster Presto or similar, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite 7 and 9 EG glass shown in Figure 8a and 8b below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area. m (specifically approved for Jansen Economy ) Maximum Area.7 m Figure 8a. Maximum Permitted Dimensions Width Page of 77 Signed

15 PYROBELITE FIRE RESISTING GLASS Pyrobelite 7 in steel framed screens for periods of minutes integrity (continued) 9 Maximum Area.7m 8 8 Figure 8b. Maximum Permitted Dimensions Forster Presto Frame Only Maximum Area. m 8 Width Page of 77 Signed

16 7 PYROBELITE FIRE RESISTING GLASS Pyrobelite 9EG in timber framed screens for periods of minutes integrity The glass shall be glazed utilising the following basic specification: Pyrobelite 9 EG Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam mm wide by 7 mm high (with o chamfer or square) hardwood glazing beads, minimum density 9 kg/m Non-combustible setting blocks mm long steel screws at mm centres ( o to glass) centres or mm long steel pins at mm centres ( o to glass) 7 7 mm by mm (minimum) hardwood perimeter frame, minimum density 9kg/m. 7 mm by mm (minimum) hardwood transoms/mullions, minimum density 9 kg/m. This Certificate of Approval relates to the sizes of Pyrobelite 9 EG glass shown in Figure 9 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. May be utilised in multipaned screen systems with shared transoms and mullions. 9 Maximum Area.7m Figure 9 Maximum Permitted Dimensions Maximum Area. m Page of 77 Signed 8 7 Width

17 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber based doorsets for periods of minutes integrity (hardwood beads) The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 7 8 Pyrobelite Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam tape mm high by 9. mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible / hardwood setting blocks mm thick hardwood aperture liner 7 mm long steel screws or pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Figure. Maximum Permitted Dimensions Page 7 of 77 Signed Width

18 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber based doorsets for periods of minutes integrity (MDF Beads) The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 7 8 Pyrobelite Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam tape mm high by 9. mm wide (including mm high by mm wide bolection with o chamfer or square) MDF glazing beads, minimum density kg/m Non-combustible / hardwood setting blocks mm thick MDF aperture liner 7 mm long steel pins (.8 mm diameter) at mm centres ( o to glass) starting at mm in from corners 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Figure. Maximum Permitted Dimensions Maximum Area. m 7 Page 8 of 77 Signed Width

19 PYROBELITE FIRE RESISTING GLASS Pyrobelite in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. 7. Pyrobelite (B safety class). Ceramic fibre based glazing tape, Superwool X7, mm x mm capped with Dow Corning Firestop 7 neutral silicone. Glazing bead mm x mm. Stud, mm diameter by mm long. Perimeter Steel section, mm x 7 mm x.7 mm (intermediate sections mm by 9 mm by.7 mm thick). Mineral wool insulation 7. Timber Setting Block (7kg/m ) The framing system shall have test evidence, such as Jansen Economy (as detailed above), or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.7m 8 Figure. Maximum Permitted Dimensions Width Page 9 of 77 Signed

20 7 PYROBELITE FIRE RESISTING GLASS Insulating Units (IGU s) including Pyrobelite in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system.. Pyrobelite (B safety class) Insulating Glazed Unit (a minimum 8 mm wide air cavity and minimum mm thick non-fire rated glass - toughened, float, laminated, coated, tinted). Note:. mm laminated glass must be used in external applications. Ceramic fibre based glazing tape, Superwool X7, mm x mm capped with Dow Corning Firestop 7 neutral silicone. Glazing bead mm x mm. Stud, mm diameter by mm long. Perimeter Steel section, mm x 7 mm x.7 mm (intermediate sections mm by 9 mm by.7 mm thick). Mineral wool insulation The framing system shall have test evidence, such as Jansen Economy (as detailed above), or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite IGU glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 8 Maximum Area.8m Figure. Maximum Permitted Dimensions Page of 77 Signed Width

21 7 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber framed screens for periods of minutes integrity The glass shall be glazed utilising the following basic specification: Pyrobelite (B safety class) Dow Corning Firestop 7 mm wide by mm thick ceramic fibre based glazing tape or mm wide by mm thick closed cell foam tape mm wide by 7 mm high (with o chamfer or square) hardwood or softwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at - mm centres or mm long steel pins at mm centres ( o to glass) 7 minimum 7 mm by mm ( mm for intermediate transoms/mullions) hardwood or softwood frame, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. May be utilised in multipaned screen systems with shared transoms and mullions. 9 Maximum Area.9m 87 Figure. Maximum Permitted Dimensions 8 Page of 77 Signed 7 Width

22 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber based doorsets for periods of minutes integrity The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobelite Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws at or pins mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Figure. Maximum Permitted Dimensions Width Page of 77 Signed

23 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber based doorsets for periods of minutes integrity The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: Pyrobelite Closed cell foam tape (Flowstrip FDP) capped with Neutral silicone capping Hardwood glazing beads (kg/m ), mm high by 8 mm wide, recessed to accept liner. Fixed with steel pins ( mm long by mm diameter) at to face of glass at mm centres ( mm in from corners) mm wide by mm thick (Intumescent Seals Ltd Therm-A-Line or Mann McGowan Palusol) Non-combustible/hardwood setting blocks Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Figure. Maximum Permitted Dimensions Width Page of 77 Signed

24 PYROBELITE FIRE RESISTING GLASS Pyrobelite in timber framed screens for periods of minutes integrity The glass shall be glazed utilising the following basic specification: 7 Pyrobelite Neutral silicone capping mm wide by mm thick ceramic fibre based glazing tape or closed cell foam tape mm wide by 7 mm high (with - o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 7 7 mm by 7 mm (minimum) hardwood perimeter framing sections, 7 mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area.9 m Figure 7. Maximum Permitted Dimensions 8 8 Maximum Area.79 m 9 8 Width 88 Page of 77 Signed

25 PYROBELITE FIRE RESISTING GLASS Pyrobelite in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. 7. Pyrobelite or Pyrobelite EG. Ceramic fibre based glazing tape, mm x mm. Glazing bead mm x mm. Screw, mm long. Steel section, mm x mm x. mm. Mineral wool insulation 7. Setting Block The framing system shall have test evidence, such as Jansen Economy, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure 8 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.7m Figure 8. Maximum Permitted Dimensions Maximum Area.77 m Page of 77 Signed 887 Width

26 PYROBELITE FIRE RESISTING GLASS Pyrobelite in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. 7. Pyrobelite. Ceramic fibre based glazing tape, mm x mm. Glazing bead mm x mm. Screw, mm long. Steel section, mm x mm x. mm. Mineral wool insulation 7. Setting Block The framing system shall have test evidence, such as Jansen Economy, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobelite glass shown in Figure 9 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area.m Figure 9. Maximum Permitted Dimensions Maximum Area.98 m Page of 77 Signed Width

27 Pyrobel in timber based doorsets for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobel or Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws or pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of (Pyrobel and Pyrobel EG) Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Figure. Maximum Permitted Dimensions Page 7 of 77 Signed Width

28 Pyrobel in timber based doorsets for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobel or Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws or pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of (Pyrobel and Pyrobel EG) Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Figure. Maximum Permitted Dimensions Page 8 of 77 Signed Width

29 Pyrobel in timber based doorsets for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobel or Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (including mm high by mm wide bolection with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of (Pyrobel and Pyrobel EG) Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 8 Maximum Area.99 m Figure. Maximum Permitted Dimensions Page 9 of 77 Signed Width

30 Pyrobel in timber based doorsets for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobel or Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide flush beads (with o chamfer or square) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of (Pyrobel and Pyrobel EG) Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area. m Figure. Maximum Permitted Dimensions 9 Width Page of 77 Signed

31 Pyrobel in timber framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed utilising the following basic specification: 7 Pyrobel and Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam or ceramic fibre based tape mm high by mm wide (with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 7 7 mm by 7 mm (minimum) hardwood perimeter framing sections, 7 mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.78 m Figure. Maximum Permitted Dimensions 9 Page of 77 Signed 8 9 Width

32 Pyrobel in timber framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed utilising the following basic specification: 7 Pyrobel and Pyrobel EG Neutral silicone capping mm wide by mm ceramic fibre based or closed cell foam tape glazing tape 7 mm high by mm wide (with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 7 7 mm by mm (minimum) hardwood perimeter framing sections, 7 mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m (density may be reduced to kg/m if 97 mm by mm (minimum) hardwood perimeter framing sections and 97 mm by mm (minimum) hardwood internal transom/mullion framing sections are used) This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area. 9 Figure. Maximum Permitted Dimensions Page of 77 Signed 9 Width

33 Pyrobel IGU in timber framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed utilising the following basic specification: 7 IGU comprising Pyrobel or Pyrobel EG glass, a minimum 8 mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)* Neutral silicone capping Dow Corning Firestop 7 mm wide by mm ceramic fibre based glazing tape Superwool X7 mm high by 7 mm wide (with o chamfer) timber glazing beads, minimum density 9kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 7 mm by 9 mm (minimum) hardwood perimeter framing sections, mm by 9 mm (minimum) timber internal transom/mullion framing sections, minimum density 9 kg/m This Certificate of Approval relates to the sizes of IGUS s comprising Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.8m Figure. Maximum Permitted Dimensions Maximum Area. m Page of 77 Signed Width

34 Pyrobel Visionline in butt jointed system for periods of minutes integrity and insulation Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed utilising the following specifications: 7 Pyrobel or Pyrobel EG or Pyrobel EG Visionline Neutral Silicone capping mm wide by mm thick ceramic fibre tape or closed cell foam tape 7 mm high by mm wide (either square of up to o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm long steel pins at mm centres ( o to glass) 7 77 mm by mm (minimum) hardwood perimeter framing sections, minimum density kg/m 8 Dow Corning Firestop 7 mm thick maximum Or Dow Corning DC 79T - mm thick maximum Or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape 8 This Certificate of Approval relates to the sizes of Pyrobel Visionline glass shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.m Figure 7. Maximum Permitted Dimensions Page of 77 Signed Width

35 Pyrobel Visionline in butt jointed system for periods of minutes integrity and insulation Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. The framing system shall have test evidence, such as Jansen Janisol, Forster Fuego Light or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions Pyrobel and EG Visionline. Neutral silicone capping. Ceramic fibre based glazing tape, mm x mm. Setting block. Fire resistant laminate, mm x. mm. Fibre reinforced strip, mm x mm 7. Glazing bead, mm x mm x. mm 8. Screw, mm long 9. Steel section, 7 mm x 9 mm x mm x. mm. Fire resistant ceramic filling. Mounting bracket. Mineral wool insulation. Dow Corning Firestop 7 or DC79T ( mm wide maximum) or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape ( mm wide maximum) This Certificate of Approval relates to the sizes of Pyrobel Visionline glass shown in Figure 8 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 8 Maximum Area.m Figure 8. Maximum Permitted Dimensions Page of 77 Signed Width

36 Pyrobel Visionline in butt jointed system for periods of minutes integrity and insulation within Schuco ADS8 FR Aluminium Framing System Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed within a Schuco ADS8 FR aluminium framed screen.. Hilti HT mm diameterxmm. Schuco Profile ref:. Clipped beads Schuco ref: 8. Schuco fireboard ref: 98. Setting block 7 mm by 7 mm by mm. Schuco EPDM glazing gasket ref: 7. Schuco glazing gasket ref: 8. Setting block mm by 8mm by mm 9. Schuco intumescent strip ref: 98. Pyrobel and EG Visionline. Joint may comprise: Dow Corning Firestop 7 or DC79T mm thick maximum Or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape mm maximum. Pyrobel Visionline. Dow Corning Firestop 7 or DC79T ( mm wide maximum) or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape ( mm wide maximum) Page of 77 Signed

37 Pyrobel Visionline in butt jointed system for periods of minutes integrity and insulation within Schuco ADS8 FR Aluminium Framing System Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. This Certificate of Approval relates to the sizes of Pyrobel Visionline glass shown in Figure 9 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 8 Maximum Area.m Figure 9. Maximum Permitted Dimensions Width Page 7 of 77 Signed

38 Pyrobel Visionline in butt jointed systems Corner Joint Options Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. This Certificate of Approval relates to the sizes Pyrobel and EG Visionline glass utilising corner joint details as shown below, for when used in conjunction with the system previously described above (for timber, Janisol, Forster Fuegolight and ADS8 framing systems). The system may include vertically orientated butt joints in a range of angles. In order to ensure the correct specification is utilised for such specialist glazing, further information should be sought from the manufacturer. The butt joint detail depends upon the angle between glass panes (in terms of butt joint component dimensions and specifications). o 9 o 9 o to 8 o Butt-Joint 8 o Butt-Joint o to 8 o Butt-Joint Corner joint specification: Item - Momentive Pensil neutral silicone Item - Gluske Kerafix FXL Page 8 of 77 Signed

39 Pyrobel IGU in timber framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed utilising the following basic specification: 7 IGU comprising Pyrobel or Pyrobel EG glass, a minimum 8 mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)* Neutral silicone capping mm wide by mm ceramic fibre based glazing tape 7 mm high by mm wide (with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres or mm steel pins at mm centres ( o to glass) 7 mm by 97 mm (minimum) hardwood perimeter framing sections, mm by 97 mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area. m Figure. Maximum Permitted Dimensions 7 7 Width Page 9 of 77 Signed

40 Pyrobel IGU in Jansen Janisol II and Forster Fuegolight steel framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a Jansen Janisol II or Forster Fuegolight framed screens. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel IGU glass (comprising Pyrobel or Pyrobel External Grade, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*) shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. * A minimum.8 mm laminated glass must be used as the secondary pane for IGU s incorporating internal grade Pyrobel. 9 Maximum Area.m Figure. Maximum Permitted Dimensions 8 Width Page of 77 Signed

41 Pyrobel (including IGU s) in steel doorsets for periods of minutes integrity and insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel profiled doorleaf framing system.. Forster Fuego Light -mm x mm (ref 7.8/T). Forster Fuego Light -mm x mm (ref 7.8/T). Beads Forster mm by mm (ref: 97). Screws mm diameter by (ref 977). Ceramic paper mm by mm. Silicone Dow Corning Firestop 7 7. Weatherstripping ref Mineral wool insulation 9. Pyrobel The steel profiled door framing system shall have test evidence, such as Forster Fuegolight, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions for the fire resistance required (i.e. minutes integrity and minutes insulation). If the proposed doorset is to be used in double-leaf configuration, the test or assessment evidence should be applicable to double-leaf configurations. Likewise, if the proposed doorset is to be used in the unlatched configuration, the available evidence should be applicable to unlatched doorsets. When used to glaze CERTIFIRE approved doorsets which have smaller apertures than allowed in this certificate, the aperture sizes specified in the doorset certificate shall take precedence. This Certificate of Approval relates to the sizes of Pyrobel glass (inc. IGU s) shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.8m Figure. Maximum Permitted Dimensions 7 Width Page of 77 Signed

42 Pyrobel in steel framed screens for periods of minutes integrity The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. 7. Pyrobel. Ceramic fibre based glazing tape, mm x mm. Glazing bead mm x mm. Screw, mm long. Steel section, mm x mm x. mm. Mineral wool insulation 7. Setting block The framing system shall have test evidence, such as Jansen Economy, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Maximum Area.9m Figure. Maximum Permitted Dimensions Maximum Area. m Width Page of 77 Signed

43 Pyrobel in steel framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system Pyrobel. Neutral silicone capping. Ceramic fibre based glazing tape, mm x mm. Setting block. Fire resistant laminate, mm x. mm. Fibre reinforced strip, mm x mm 7. Glazing bead, mm x mm x. mm 8. Screw, mm long 9. Steel section, 7 mm x 9 mm x mm x. mm. Fire resistant ceramic filling. Mounting bracket. Mineral wool insulation The framing system shall have test evidence, such as Jansen Janisol II, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobel glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 8 Maximum Area.8m Figure. Maximum Permitted Dimensions Maximum Area.m Width Page of 77 Signed

44 Pyrobel in steel framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system.. Pyrobel and Pyrobel EG. Neutral silicone capping. Ceramic fibre based glazing tape, mm x mm. Setting block 7. Fire resistant laminate, mm x. mm. Fibre reinforced strip, mm x mm 8 7. Glazing bead, mm x mm x. mm 9 8. Screw, mm long 9. Steel section, 7 mm x 9 mm x mm x. mm. Fire resistant ceramic filling. Mounting bracket. Mineral wool insulation The framing system shall have test evidence, such as Jansen Janisol II or Forster Fuegolight, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.m 9 Figure. Maximum Permitted Dimensions 9 Width Page of 77 Signed

45 Pyrobel IGU s in Schuco BF+ and BF+ aluminium framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a Schuco BF+ or a BF+ aluminium framed screen. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel IGU glass (comprising Pyrobel or Pyrobel External Grade, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*) shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. * A minimum.8 mm laminated glass must be used as the secondary pane for IGU s incorporating internal grade Pyrobel. 8 Maximum Area.8m Figure. Maximum Permitted Dimensions Maximum Area. m 77 8 Width Page of 77 Signed

46 Pyrobel IGU s in SAPA Fascade Fire aluminium framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a SAPA Fascade Fire aluminium framed screen. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel IGU glass (comprising Pyrobel or Pyrobel External Grade, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*) shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. * A minimum.8 mm laminated glass must be used as the secondary pane for IGU s incorporating internal grade Pyrobel. 9 Maximum Area.m Figure 7. Maximum Permitted Dimensions Width Page of 77 Signed

47 Pyrobel and Pyrobel EG in Schuco ADS8 aluminium framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a Schuco ADS8 aluminium framed screen.. Hilti HT mm diameterxmm. Schuco Profile ref:. Clipped beads Schuco ref: 8. Schuco fireboard ref: 98. Setting block 7 mm by 7 mm by mm. Schuco EPDM glazing gasket ref: 7. Schuco glazing gasket ref: 8. Setting block mm by 8mm by mm 9. Schuco intumescent strip ref: 98. Pyrobel and EG This Certificate of Approval relates to the sizes of Pyrobel glass (comprising Pyrobel or Pyrobel External Grade) shown in Figure 8 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. Note: the approval is only valid when the insulated sections of the frame face the fire hazard direction. 9 Maximum Area.89m Figure 8. Maximum Permitted Dimensions Page 7 of 77 Signed 87 Width

48 PYROBELITE FIRE RESISTING GLASS Pyrobel 7N and 7N EG in timber framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed utilising the following basic specification: 7 Pyrobel 7N or 7N EG Neutral silicone capping mm wide by mm ceramic fibre based glazing tape or closed cell foam mm high by 7 mm wide (with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws or pins at mm centres ( o to glass) 7 87 mm by mm (minimum) hardwood perimeter framing sections, 87 mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobel 7N or 7N EG glass shown in Figure 9 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.7m 87 Figure 9. Maximum Permitted Dimensions Maximum Area.8 m Page 8 of 77 Signed 8 9 Width

49 PYROBELITE FIRE RESISTING GLASS Pyrobel 7N or 7N EG in insulated steel framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a Jansen Janisol C frame, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions.. Hilti HT mm diameterxmm. Superwool X7 9kg/m. Janisol C 7 mm by mm. Clipped Beads, steel profile mm by mm. Setting block 7 mm by mm by mm. mm diameter by mm long steel screw 7. Ceramic paper mm by mm 8. Silicone Dow Corning Firestop 7 This Certificate of Approval relates to the sizes of Pyrobel 7N or 7N EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.8m Figure. Maximum Permitted Dimensions Maximum Area. m 7 7 Width Page 9 of 77 Signed

50 7 PYROBELITE FIRE RESISTING GLASS Pyrobel 7N or 7N EG in uninsulated steel framed screens for periods of minutes integrity only The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system.. Pyrobel 7N or 7N EG. Ceramic fibre based glazing tape, Superwool X7, mm x mm capped with Dow Corning Firestop 7 neutral silicone. Glazing bead mm x mm. Stud, mm diameter by mm long. Perimeter Steel section, mm x 7 mm x.7 mm (intermediate sections mm by 9 mm by.7 mm thick). Mineral wool insulation 7. Non-combustible setting blocks The framing system shall have test evidence, such as Jansen Economy (as detailed above), Forster Presto or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobel 7N or 7N EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.7m 8 8 Figure. Maximum Permitted Dimensions Maximum Area. m Page of 77 Signed 8 9 Width

51 Pyrobel in timber based doorsets for periods of minutes integrity and insulation The glass shall be glazed within a previously fire tested or CERTIFIRE approved timber based doorset utilising the following basic specification: 8 7 Pyrobel and Pyrobel EG Neutral silicone capping mm wide by mm thick closed cell foam tape mm high by. mm wide (including mm high by mm wide bolection with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible/hardwood setting blocks mm thick hardwood aperture liner (not required for hardwood cored door leaves) 7 mm long steel screws at mm centres ( o to glass) 8 Nominally mm thick FD door leaf The doorset shall be CERTIFIRE approved or have test evidence for the inclusion of apertures of the proposed dimensions. This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Figure. Maximum Permitted Dimensions Width Page of 77 Signed

52 Pyrobel in hardwood timber framed screens for periods of minutes integrity and insulation The glass shall be glazed utilising the following basic specification: 7 Pyrobel and Pyrobel EG Neutral Silicone capping mm wide by mm thick closed cell foam tape 7 mm high by mm wide (with o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres ( o to glass) 7 9 mm by mm (minimum) hardwood perimeter framing sections, 9 mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above systems. The aspect ratio of the glass may be unlimited within these aperture dimensions. 87 Maximum Area.7 m Figure. Maximum Permitted Dimensions Width Page of 77 Signed

53 Pyrobel in softwood timber framed screens for periods of minutes integrity and insulation The glass shall be glazed utilising the following basic specification: 7 Pyrobel and Pyrobel EG Neutral Silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (with o chamfer) softwood glazing beads, minimum density 9 kg/m Non-combustible setting blocks mm long steel screws at mm centres ( o to glass) 7 98 mm by mm (minimum) hardwood perimeter framing sections, 98 mm by 7 mm (minimum) softwood internal transom/mullion framing sections, minimum density 9 kg/m This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above systems. The aspect ratio of the glass may be unlimited within these aperture dimensions. 88 Maximum Area. m 7 7 Figure. Maximum Permitted Dimensions Maximum Area. m Page of 77 Signed Width

54 7 PYROBEL FIRE RESISTING GLASS Insulating Units (IGU s) including Pyrobel in timber framed screens for periods of minutes integrity and insulation The IGU shall be glazed utilising one of the following specifications: IGU comprising Pyrobel or Pyrobel External Grade, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*. IGU s may be triple glazed to a similar specification with the Pyrobel forming the central pane and a pane of non-fire rated glass positioned each side of the Pyrobel Neutral Silicone capping mm wide by mm thick closed cell foam tape mm high by mm wide (either square of up to o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres ( o to glass) 7 mm by mm (minimum) hardwood perimeter framing sections, mm by mm (minimum) hardwood internal transom/mullion framing sections, minimum density kg/m * A minimum.8 mm laminated glass must be used as the secondary pane for IGU s incorporating internal grade Pyrobel. This Certificate of Approval relates to the sizes of IGU s including Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 87 Maximum Area.7 m Figure. Maximum Permitted Dimensions Page of 77 Signed Width

55 Pyrobel in steel framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested (see example below) or CERTIFIRE approved steel framing system utilising the following basic specification. The edge cover to each pane shall be no less than mm minimum 7 Pyrobel and Pyrobel EG Neutral silicone capping mm wide by - mm thick ceramic fibre based glazing tape Non-combustible setting blocks Steel Section mm by mm by mm mm by 9 mm calcium silicate 7 mm long steel screws at mm centres This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.m (note these glass dimensions are only applicable when Janisol framing system is used) 7 Maximum Area.7m (note these glass dimensions are only applicable when Forster Fuegolight framing system is used) Figure. Maximum Permitted Dimensions Maximum Area.9 m 7 Width Page of 77 Signed

56 Pyrobel in Steel Doorsets for periods of minutes integrity and minutes insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel profiled doorleaf framing system. The steel profiled door framing system shall have test evidence, such as RP Isofeu, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions for the fire resistance required (i.e. minutes integrity and minutes insulation). If the proposed doorset is to be used in double-leaf configuration, the test or assessment evidence should be applicable to double-leaf configurations. Likewise, if the proposed doorset is to be used in the unlatched configuration, the available evidence should be applicable to unlatched doorsets. When used to glaze CERTIFIRE approved doorsets which have smaller apertures than allowed in this certificate, the aperture sizes specified in the doorset certificate shall take precedence. This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Pyrobel or Pyrobel EG. Neoprene glass edge seal. Neoprene glass edge seal. Intumescent seal mm x. mm. Neoprene door edge seal. Steel glazing bead 7. Screw, mm long 8. Steel section 9. Infill to section. Steel section. Steel section. Insulation mm x mm. Siporex board. Mineral wool insulation Maximum Area.9m Figure 7. Maximum Permitted Dimensions Page of 77 Signed Width

57 Insulating Units (IGU s) including Pyrobel in steel doorsets for periods of minutes integrity and insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel profiled doorleaf framing system IGU comprising Pyrobel or Pyrobel EG glass, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*. Neoprene glass edge seal. Neoprene glass edge seal. Intumescent seal mm x mm. Neoprene door edge seal. Steel glazing bead 7. Screw, mm long 8. Steel section 9. Infill to section. Steel section. Steel section. Partition wall *A minimum.8 mm laminated glass must be used as the external pane for IGU s incorporating internal grade Pyrobel. The steel profiled door framing system shall have test evidence, such as RP Technik Isofeu, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions for the fire resistance required (i.e. minutes integrity and minutes insulation). If the proposed doorset is to be used in double-leaf configuration, the test or assessment evidence should be applicable to double-leaf configurations. Likewise, if the proposed doorset is to be used in the unlatched configuration, the available evidence should be applicable to unlatched doorsets. When used to glaze CERTIFIRE approved doorsets which have smaller apertures than allowed in this certificate, the aperture sizes specified in the doorset certificate shall take precedence. This Certificate of Approval relates to the sizes of Pyrobel or EG glass (in IGU s) shown in Figure 8 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 87 Maximum Area.8m Figure 8. Maximum Permitted Dimensions Page 7 of 77 Signed 898 Width

58 Insulating Units (IGU s) including Pyrobel in steel screen for periods of minutes integrity and insulation The glass shall be glazed within a previously fire tested, such as Jansen VISS, Jansen Janisol C or Forster Thermfix Vario or CERTIFIRE approved steel framing system utilising the following basic specification. The edge cover to each pane shall be no less than mm minimum IGU comprising Pyrobel or Pyrobel EG glass, a minimum 8 mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*. Rubber profile, mm x 7 mm. Rubber profile, 7 mm x mm. Steel section, mm x mm x mm. Anchor bolt. Setting block 7. Steel section, 8 mm x mm x mm 8. Steel bolt, 8 mm long 9. Aluminium section, mm x 8 mm x. mm. Calcium silicate board. Mineral wool insulation *A minimum.8 mm laminated glass must be used as the external pane for IGU s incorporating internal grade Pyrobel. This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG glass (in IGU s) shown in Figure 9 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.m 8 Figure 9. Maximum Permitted Dimensions Maximum Area.8 m Page 8 of 77 Signed Width

59 Pyrobel and Pyrobel EG in SAPA SFB 7 and SCHUCO FIRESTOP II aluminium framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a SAPA SFB 7 aluminium framed screen. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 7 Maximum Area =.8m Figure. Maximum Permitted Dimensions Width Page 9 of 77 Signed

60 Pyrobel and Pyrobel EG in SCHUCO ADS8 aluminium framed screens for periods of minutes integrity and minutes insulation The glass, Pyrobel and EG, shall be glazed within a Schuco ADS8 aluminium framed screen see below for diagrammatic details: This Certificate of Approval relates to the sizes of Pyrobel glass (comprising Pyrobel or Pyrobel External Grade) shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area.m Figure. Maximum Permitted Dimensions 7 Page of 77 Signed

61 Pyrobel IGU s in SCHUCO FIRESTOP II aluminium framed screens for periods of minutes integrity and minutes insulation The glass shall be glazed within a Schuco Firestop II aluminium framed screen. Approval is given only when the Pyrobel glass component faces the fire hazard direction. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel IGU glass (comprising Pyrobel or Pyrobel External Grade, a minimum mm wide air cavity and minimum mm thick non-fire rated glass (toughened, float, laminated, coated, tinted)*) shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. * A minimum.8 mm laminated glass must be used as the secondary pane for IGU s incorporating internal grade Pyrobel. 8 Maximum Area =.9m Figure. Maximum Permitted Dimensions Page of 77 Signed

62 Pyrobel Visionline in butt jointed system for periods of minutes integrity and insulation Note: Pyrobel Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed utilising the following specifications: 7 Pyrobel or Pyrobel EG Visionline Neutral Silicone capping mm wide by mm thick ceramic fibre tape or closed cell foam tape 7 mm high by mm wide (either square of up to o chamfer) hardwood glazing beads, minimum density kg/m Non-combustible setting blocks mm long steel screws at mm centres ( o to glass) 7 9 mm by mm (minimum) hardwood perimeter framing sections, minimum density kg/m 8 Dow Corning Firestop 7 or DC79T mm thick maximum Or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape mm maximum 8 This Certificate of Approval relates to the sizes of Pyrobel Visionline glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.97m Figure. Maximum Permitted Dimensions Page of 77 Signed 8 Width

63 Pyrobel & EG Visionline in butt jointed system for periods of minutes integrity and insulation Note: Pyrobel & EG Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. The framing system shall have test evidence, such as Jansen Janisol C, Forster Fuego Light, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions.. Hilti HT mm diameterxmm. Superwool X7 9kg/m. Janisol C 7 mm by mm. Clipped Beads, steel profile mm by mm. Setting block 7 mm by mm by mm. mm diameter by mm long steel screw 7. Ceramic paper mm by mm 8. Silicone Dow Corning DC79T 9. - Pyrobel or EG Visionline Note: joint may comprise: Dow Corning Firestop 7 or DC79T mm thick maximum Or Henkel Ceresit B capping to off. mm by mm ceramic fibre tape mm maximum 9 This Certificate of Approval relates to the sizes of Pyrobel Visionline glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.m Figure. Maximum Permitted Dimensions Page of 77 Signed Width

64 Pyrobel & EG Visionline in butt jointed system for periods of minutes integrity and insulation within Schuco ADS8 FR Aluminium Framing System Note: Pyrobel & EG Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. The glass shall be glazed within a Schuco ADS 8 FR aluminium framed screen. Please consult the frame manufacturer for drawings of glazing system.. PYROBEL Visionline, structure //8//, nominal thickness. +/-. mm, size x 888 mm pieces and 89 x 888 mm piece. a Promat-SYSTEMGLAS-silicone, transparent b Silicone DC 7, grey. Schüco Profile ref. Clipped Beads Schüco ref 7 8. Clipped Beads Schüco ref 7 8. Schüco fireboard ref 7. Schüco fireboard ref 8. Schüco fireboard ref 9. Schüco fireboard ref. Schüco EPDM glazing gasket ref. Schüco EPDM glazing gasket ref. Intumescent strip PROMASEAL-PL.8 x 8 mm. Fixation : Hilti HT x mm. Setting Block PROMATECT-H, (L) x (W) 8 x (H) mm. Setting Block PROMATECT-H, (L) x (W) x (H) mm. INSULFRAX : 8 kg/m³ 7. Schüco anchor steel plate ref 8. Schüco steel scew ref 9 9. Schüco glazing clip ref (each at 8 mm). Schüco Isolator ref, x mm, L = mm, bonded in all connection of profile. Supporting construction. Pyrobel & EG Visionline. Dow Corning Firestop DC7 ( mm wide maximum) or Promat-SYSTEMGLAS-silicone ( mm wide maximum) Page of 77 Signed

65 Pyrobel & EG Visionline in butt jointed system for periods of minutes integrity and insulation within Schuco ADS8 FR Aluminium Framing System Note: Pyrobel & EG Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. This Certificate of Approval relates to the sizes of Pyrobel & EG Visionline glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 9 Maximum Area. m Figure. Maximum Permitted Dimensions Width Page of 77 Signed

66 Pyrobel and EG Visionline in butt jointed systems Corner Joint Options Note: Pyrobel and EG Visionline butt jointed requires special edge processing and should be ordered as such. Please contact an approved Pyrobel stockist or AGC for further details. This Certificate of Approval relates to the sizes Pyrobel and EG Visionline glass utilising corner joint details as shown below, for when used in conjunction with the system previously described above (for timber, Janisol C, Forster Fuegolight and ADS8 framing systems). The system may include vertically orientated butt joints in a range of angles. In order to ensure the correct specification is utilised for such specialist glazing, further information should be sought from the manufacturer. The butt joint detail depends upon the angle between glass panes (in terms of butt joint component dimensions and specifications). o 9 o 9 o to 8 o Butt-Joint 8 o Butt-Joint o to 8 o Butt-Joint Corner joint specification: Item - Momentive Pensil neutral silicone Item - Gluske Kerafix FXL Item - Page of 77 Signed

67 Pyrobel, Pyrobel EG and Pyrobel IGU in steel framed screens for periods of 9 minutes integrity and insulation The glass shall be glazed within a previously fire tested (see example below) or a CERTIFIRE approved steel framing system. The framing system shall have test evidence, such as Jansen Janisol C or Forster FuegoLight, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. 9. Hilti HT mm diameterxmm. Superwool X7 9kg/m. Janisol C 7 mm by mm. Clipped Beads, steel profile mm by mm. Setting block 7 mm by mm by mm. mm diameter by mm long steel screw. Ceramic paper mm by mm. Silicone Dow Corning DC79T - Pyrobel or EG or IGU (min air cavity mm + min mm non-fire rated glass This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG and Pyrobel IGU glass shown in Figure below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.9 m (single glazed only) Figure. Maximum Permitted Dimensions Maximum Area. m (single and IGU glazed) Maximum Area. m (single and IGU glazed) 9 Width Page 7 of 77 Signed

68 Pyrobel, Pyrobel EG and Pyrobel IGU in FORSTER FUEGO LIGHT T9 steel doorsets for periods of 9 minutes integrity and insulation The glass shall be glazed within fully latched/bolted Forster Fuego Light T9 doorsets. Please consult the frame manufacturer for drawings of glazing system. This Certificate of Approval relates to the sizes of Pyrobel and Pyrobel EG and Pyrobel IGU glass shown in Figure 7 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions Maximum Area.9 m (single glazed only) Figure 7. Maximum Permitted Dimensions Maximum Area. m (single and IGU glazed) Maximum Area. m (single and IGU glazed) 9 Width Page 8 of 77 Signed

69 Pyrobel N & N EG in steel framed screens for periods of minutes integrity and insulation The glass shall be glazed within a previously fire tested (see diagrammatic example below) or CERTIFIRE approved steel framing system utilising the following basic specification. The framing system shall have test evidence, such as Forster Fuego, or be CERTIFIRE approved for the inclusion of apertures of the proposed dimensions. The edge cover to each pane shall be no less than mm minimum.. Hilti HT mm dieameterxmm. Steel profile Forster Fuego mm by mm. Clipped beads mm by mm. Setting block 7 mm by mm x mm. Steel screw mm diameter, mm long. Ceramic paper mm by mm 7. Setting block mm by mm by mm 8. Silicone Dow Corning Firestop 7 9. Intumescent Strip Palusol mm by mm. Pyrobel N & N EG This Certificate of Approval relates to the sizes of Pyrobel N glass shown in Figure 8 below, when used in conjunction with the above system. The aspect ratio of the glass may be unlimited within these aperture dimensions. 89 Maximum Area.7m Figure 8. Maximum Permitted Dimensions Maximum Area. m 7 Width Page 9 of 77 Signed