|
|
- Alban Pearson
- 7 years ago
- Views:
Transcription
1 1 of 23 10/6/2011 1:11 PM Change Mode for your Spectrum DX6i Radio From MODE 2 to MODE 1 Disclaimer: Before you begin, please keep in mind that any of this modification probably invalidate your warranty, any damage caused to your Tx following these instructions is your responsability, all steps are reversible but you can not guarantee that you wont loose a screw or break some tiny plastic part, so be very carefull. Change the software. To enter the hidden menu: Go to the COPY/RESET menu inside the SETUP LIST.
2 2 of 23 10/6/2011 1:11 PM Choose RESET. (DRAGONUS is the name i have assigned to my model 1 in the Tx memory)
3 3 of 23 10/6/2011 1:11 PM When you are asked yes / no highlight the "list" button in the top right.
4 4 of 23 10/6/2011 1:11 PM After this switch the AIL D/R switch at the top right from position 1 to 0 two or three times..
5 5 of 23 10/6/2011 1:11 PM after this procedure the sender should open the menu to change mode.
6 6 of 23 10/6/2011 1:11 PM Choose your mode with the dial and push the dial to accept. Change the spring from the right stick to te left. Tools you will need:
7 7 of 23 10/6/2011 1:11 PM I reccomend you use your styrofoam packaging to protect your transmitter from scratches.
8 8 of 23 10/6/2011 1:11 PM 1.- Remove the 4 "AA" batteries from the batteries compartement. 2.- Remove the back part of the transmitter case, unscrewing the 6 phillips head screws. 3.- Before you remove this 3 connectors that connect both parts, mark with a "sharpie" pen, to reconnect them as they need to be.
9 9 of 23 10/6/2011 1:11 PM 4.- Untight this 2 screws and remove the friction plate.
10 10 of 23 10/6/2011 1:11 PM 5.- I used my RC wrench to remove this nut (4mm hex)
11 11 of 23 10/6/2011 1:11 PM 6.-Screw into the new position (some people doesnt use this friction plate so steps 5 thru 8 can be ommited).
12 12 of 23 10/6/2011 1:11 PM 7.- Use silicon oil to lube the plastic were the friction plate makes contact.
13 13 of 23 10/6/2011 1:11 PM 8.- Screw the friction plate as the picture shows, black screw goes almost all the way and the silver screw is to adjust the friction feel that you like the most, move the throttle stick and adjust as desired.
14 14 of 23 10/6/2011 1:11 PM 9.- Remove the right stick spring (be carefull not to loose it or bent it).
15 15 of 23 10/6/2011 1:11 PM 10.- Remove this plastic part.
16 16 of 23 10/6/2011 1:11 PM 11.- This 3 pins needs to be removed from Right Stick to be put in the Left Stick.
17 17 of 23 10/6/2011 1:11 PM 12.- Use a bent nose pliers like the picture and be very carefull since there is very little space.
18 18 of 23 10/6/2011 1:11 PM 13.- Remove one by one and place in the other stick, the position is the same but remember that the stick is rotated 180.
19 19 of 23 10/6/2011 1:11 PM 14.- Twist a little first to make it easy to pull out.
20 20 of 23 10/6/2011 1:11 PM 15.- Use a 2mm hex screw remover to remove the right stick from the front half case, this are just 4 screws.
21 21 of 23 10/6/2011 1:11 PM 16.- Remove the little plastic part that keeps the spring tensioner in position, you need to use a small screwdriver to help to push it out from the inside, reassemble the right stick and make this same steps 15 and 16 to put in the left stick.
22 22 of 23 10/6/2011 1:11 PM 17.- Reattach the spring into position, put the tension adjusting screw into position and adjust the same tension as the horizontal stick Reconnect all 3 connector to the printed circuit (notice they original position) reassemble both transmitter case parts using the 6 phillips head screws.
23 23 of 23 10/6/2011 1:11 PM 19.- OK now you have a new MODE 1 Brand New Transmitter. CREDITS: Software Procedure: Hardware Procedure, Pictures and Text: Max3Design
TETRIX Getting Started Guide. Dispenser Building Guide. Step 1. Parts Needed. Tip. 1x Single-Servo Motor Bracket. 1x 96 mm Channel
Step 1 1x 96 mm Channel 1x Single-Servo Motor Bracket 3x 1/2" SHCS 3x Kep Nut Tip Ensure that the teeth of the nut face the head of the screw. 173 Extensions Step 2 1x Servo Horn 1x Flat Bracket 3x 5/16"
More informationTime needed: ~3h for lid replacement only. Add 1h for operation harness in lid and ~2h more for installing drive unit and cable harness in trunk.
DIY for replacing trunk lid and/or retrofitting electrical operation of trunk lid. This document is meant to be a support and give advice on the procedure but I will take no responsibility for any damage
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 24393 ACCORD (DX, LX) SYSTEM 2-AND 4-DOOR Issue Date AUG 2002 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit panel
More informationGE Wireless Devices Battery Replacement
60-506-319.5 Crystal Smoke Detector Two 9V Duracell 9V 1. Twist counter-clockwise until detector become loose from base. 2. Replace batteries observing correct polarity. 3. Replace detector by twisting
More informationSony Cyber-shot DSC-T9 Motherboard
Sony Cyber-shot DSC-T9 Motherboard Replacement This guide gives instructions to the user to install a motherboard into the Sony Cyber-shot DSC-T9 camera. Written By: Stephannie Allen INTRODUCTION This
More informationRetrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
More informationKEYPAD LOCK RETROFIT KIT
KEYPAD LOCK RETROFIT KIT INSTRUCTIONS FOR ASSEMBLY IMPORTANT READ & SAVE THESE INSTRUCTIONS Tools Required for Assembly 5/32 hex (Allen) wrench #2 Phillips screwdriver Isopropyl alcohol or alcohol wipes
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
More informationIntelliChlor Flow-Temperature Switch Replacement Kit Installation Guide
IntelliChlor Flow-Temperature Switch Replacement Kit Installation Guide Technical Support Sanford, North Carolina (8 A.M. to 5 P.M.) Moorpark, California (8 A.M. to 5 P.M.) Phone: (800) 831-7133 Fax: (800)
More informationGuide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
More informationINSTALLATION MANUAL INSIDE PASSENGER COMPARTMENT. HFC 134a FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH
HFC 134a Ozone Friendly Refrigerant FOR EUROPEAN SPEC. / GENERAL SPEC. AIR CONDITIONING ENGLISH AAAMU-60 / INSIDE PASSENGER COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All Rights Reserved. This
More informationContents. Front Derailleurs... 2. Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation...
Contents... 2 Part One - Planning... 2 I. Objectives... 2 II. Materials Needed... 2 III. Setting...2 IV. Evaluation... 2 Part Two - Activity Instructions... 3 Steps to Adjusting and Replacing... 3 Disassemble...
More informationhttp://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -
More informationAstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
More informationINSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
More informationReplacing a Vantage Vue Transmitter
Replacing a Vantage Vue Transmitter Included in this replacement transmitter kit: SIM transmitter Cable tray Instructions Tools Required Phillips head screwdriver Small pliers To replace the transmitter
More information3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationPRODUCT MANUAL SPECIFICATIONS SAFETY PRECAUTIONS. 1460mm/57.48in 1112mm/43.78in 27.74dm²/429.96in² 1600g/56.50oz 57.68g/dm²
SPECIFICATIONS SAFETY PRECAUTIONS PRODUCT MANUAL Wing span: Length: Wing area: Flying weight: Wing loading: 1460mm/57.48in 1112mm/43.78in 27.74dm²/429.96in² 1600g/56.50oz 57.68g/dm² This electric R/C model
More informationBMW X5 Tail Lamp Assembly Repair. By Myles H. Kitchen M.H. KITCHEN & ASSOCIATES www.auto-electronic.com Email: MHKitchen@aol.com
BMW X5 Tail Lamp Assembly Repair By Myles H. Kitchen M.H. KITCHEN & ASSOCIATES www.auto-electronic.com Email: MHKitchen@aol.com INTRODUCTION A common problem experienced by BMW X5 owners is a Check Rear
More informationSIG 556 Match Sear/Hammer Installation
SIG 556 Match Sear/Hammer Installation ShootingSight LLC 2012 Safety Warning Always verify your firearm is unloaded before working on it. These instructions are meant as a supplemental guide to an armorer
More informationDisassembling the Wii
Username: Password: Login Disassembling the Wii Method : Taking it Apart There are plenty of reasons to take apart a wii, whatever your case may be here's a guide to doing it. REQUIRED TOOLS AND ITEMS
More information430 Power/Electronics Replacement
Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed
More informationJoplin Rebuild Instructions
Joplin Rebuild Instructions This is a step by step list of instruction on how to rebuild the Crankbrothers Joplin post. It may not always be required to completely tear-down the post to do the work needed
More informationWritten By: Walter Galan
Installing iphone 4S Display Assembly Written By: Walter Galan TOOLS: Phillips 00 Screwdriver (1) Plastic Opening Tools (1) PARTS: iphone 4S Display Assembly (1) iphone 4 and 4S Screen Protector (1) Small
More informationAlfa Romeo 147 On board instruments installation guide
Alfa Romeo 147 On board instruments installation guide Alfa Romeo 147 On board instruments installation guide This guide is describing how I installed oil temperature and oil pressure gauges to my Alfa
More informationNo Rainfall Data is Collected
No Rainfall Data is Collected There are a number of issues that can cause the system to not collect rainfall data, from clogged collectors to hardware failure or improper part replacement. The most common
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
More informationINSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
More informationPRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129
PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,
More informationLED Security Spotlight User Manual
MOT ION-TR ACKING LED Security Spotlight User Manual www.jascoproducts.com 1-800-654-8483 2 TABLE OF CONTENTS Parts List 3 Questions? Missing Parts? 4 Installation (Wall mount) 6-9 Installation (Eave mount)
More informationUser Manual. Instructions for installing the Sure Stitch on the Next Generation Quilting Frame. Parts Included:
User Manual Instructions for installing the Sure Stitch on the Next Generation Quilting Frame. Parts Included: 1: Display Console 1: Control Box 2: Encoder (Wires attached) (Not Shown) 1: 5v Power Supply
More informationHP Laser Jet 4200/4240/4250/4300/4350 Swing Plate
HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate 1 Swing Plate Assembly-RM1-0043 1 Swing Plate Kit-5851-2766 (RM1-0043 plus RM1-1091 gear) CAUTION: Fuser may be hot. Turn off printer, unplug it and allow
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationLS-1 Series Tungsten Halogen Light Sources Installation and Operation Instructions
LS-1 Series Tungsten Halogen Light Sources Installation and Operation Instructions Description The LS-1 Series of tungsten halogen light sources are versatile, white-light lamps optimized for use in the
More informationNational Optical & Scientific Instrument Inc. 11113 Landmark 35 Drive San Antonio, Texas 78233 Phone (210) 590-9010 Fax (210) 590-1104
National Optical & Scientific Instrument Inc. 11113 Landmark 35 Drive San Antonio, Texas 78233 Phone (210) 590-9010 Fax (210) 590-1104 INSTRUCTIONS FOR STEREOSCOPIC MICROSCOPES MODEL NUMBERS 400 400TL
More informationBuild Tips for Sakura Zero S
Build Tips for Sakura Zero S Revision Control Revision Revision Notes Report By Reviewed By Rev0 First Draft Marc Baynham Introduction The way in which a competition electric radio controlled car such
More informationINSTRUCTION MANUAL. Black Angel. www.copterx.com. Features. Kit Helicopter. Copyright 2009 KY MODEL Company Limited.
INSTRUCTION MANUAL Features - Carbon fiber main blade, tail blade, fly paddle, tail fin for extra weight saving and durability. - CNC machined high grade aluminum rotor head and tail gear box to ensure
More informationMAINTENANCE & TROUBLESHOOTING
MAINTENANCE & TROUBLESHOOTING This section describes how to: clean the lens clean the fan intake filter replace the projection lamp replace the batteries in the remote control use the Kensington lock feature
More informationtornado rotorz safety notice
TORNADO ROTORZ tornado rotorz safety notice This product uses substantial battery power and can reach considerable speed. May present danger if operated incorrectly; please read and digest instructions
More informationIMPACT SPRINKLER TROUBLESHOOTING GUIDE
RAIN USE AND OPERATION BIRD IMPACT SPRINKLER TROUBLESHOOTING GUIDE The diagrams below depict typical Rain Bird sprinklers with all available controls. Your particular model may have only some of these
More informationInstall Guide CT100. Caution. Caution ENGLISH. disconnect the power supply before beginning work.
Install Guide CT100 PG 1 Caution top cover Your thermostat is a precise instrument, handle it with care. Turn off electricity to the system before installing or servicing thermostat or any part of the
More information4.3-inch Back-Up Camera
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
More informationPARTS NEEDED FOR CONVERTING FROM LP TO NG
1 6 7 8 3 5 4 10 9 2 PARTS NEEDED FOR CONVERTING FROM LP TO NG Number Description 1 30" NG Manifold 2 NG side burner valve 3 NG Regulator 4 Rear I/R NG orifice 4 Rear I/R NG orifice 5 Side burner NG orifice
More informationOWNER S MANUAL. Permolock C3. Docking system for Power wheelchair in vehicle
OWNER S MANUAL US Permolock C3 Docking system for Power wheelchair in vehicle How to contact Permobil Head Office of the Permobil group Permolock C3 Docking system for electric wheelchair in vehicle Produced
More informationConvert your Losi Micro Vehicle from Brushed to Brushless power
Convert your Losi Micro Vehicle from Brushed to Brushless power Before we begin the conversion, let s make sure we have all the components you will need. Parts Required: A You will need a NEW servo to
More informationQuickie Rhapsody Service Manual
Quickie Rhapsody Service Manual 2006 Sunrise Medical Inc. 101976 Rev A Quickie Rhapsody Service Manual Contents Introduction... 0.1 VR2 Controller... 0.2 Plugs/Connectors... 0.3 Basic Tool List & Main
More informationROTOR LOADER OWNER S MANUAL
ROTOR LOADER OWNER S MANUAL ROTOR LOADER OWNER S MANUAL WARNING IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES. Misuse of paintball equipment may cause serious injury or death. QUICK SET-UP GUIDE BATTERY
More information9001014 CRUISE CONTROL KIT INSTALLATION INSTRUCTIONS
9001014 CRUSE CONTROL KT NSTLLTON NSTRUCTONS OR MODEL PB-413T/PB-620 Please retain these instructions for future reference. Tools Required: 5 mm hex wrench, screwdriver Parts Required: PB-620 Cruise Control
More informationPOLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS
POLEMOUNT FIELD FIX ASSEMBLY INSTRUCTIONS Polemount Field Fix Support If you have any questions or incur any problems installing or using the new Polemount, please use Miovision s Support System by emailing
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationWeatherproof Extension Case (Part # S-EXT-CASE)
Weatherproof Extension Case (Part # S-EXT-CASE) The Weatherproof Extension Case is a PVC housing designed to enclose the coupler that connects two modular cables, such as two smart sensor cables or two
More informationCleaning Instructions, Pilot Replacement and Valve Change. Model No.: 233010 Natural Gas
Cleaning Instructions, Pilot Replacement and Valve Change Model No.: 233010 Natural Gas 8mm open-end wrench 9mm open-end wrench 10mm open-end wrench 12mm open-end wrench 13mm open-end wrench Phillips screw
More informationOceanscience Cable Chimp II Cableway ROV System User Guide and Warranty
Oceanscience Cable Chimp II Cableway ROV System User Guide and Warranty Page 1 Table of Contents Introduction Page 3 Overview Page 3 Setup and Operation Page 5 Remote Control Page 6 Power Management Page
More informationMondeo 2.0 TDCI Variable Vane Turbo Cleaning
Mondeo 2.0 TDCI Variable Vane Turbo Cleaning My Car: '05 Mondeo 2.0 TDCI Euro IV Turbo with Electronic Actuator (The variable vane turbo with the vacuum actuator is much the same process I believe) Guide
More informationBTH360-S Bluetooth Stereo Headset Specifications & User's Guide
BTH360-S Bluetooth Stereo Headset Specifications & User's Guide www.kinivo.com Email: support@kinivo.com Warranty BTH360-S is covered under 1 year limited hardware warranty. Please contact Kinivo technical
More informationPost Mount Light Installation*
Post Mount Light Installation* *For the general installation of most Post Mount Spotlights, many vehicles may need slight modifications to these instructions. You will need the following tools: High torque
More informationService Guide. Gateway M275
Service Guide Gateway M275 Contents Replacing Gateway M275 Components.................................... 1 Identifying the convertible tablet PC model...................................... 2 Identifying
More informationDL-9000 Ticket Eater with AP-100 Logic Board
DL-9000 Ticket Eater with AP-100 Logic Board DL-9000 Ticket Eater by Deltronic Labs February 2013 1 Table of Contents Initial Setup... 3 Handling Messages on the Display... 3 DL Ticket Eater Manager Software...
More informationLiteAide OWNER'S MANUAL PREASSEMBLED AUTOMATIC SECURITY FLOODLIGHTS MOTION SENSOR SECURITY LIGHTING SYSTEMS
OWNER'S MANUAL PREASSEMBLED AUTOMATIC SECURITY FLOODLIGHTS MOTION SENSOR SECURITY LIGHTING SYSTEMS LiteAide HE-100B HE-100BW HE-112 HE-112W HE-117 HE-117W HE-117-2B OWNER'S MANUAL FLOOD LAMPS (BULBS) Your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39408 Issue Date MAY 2008 PARTS LIST Steering Wheel Trim (With Cruise and Audio) P/N 08Z13-SZA-130B (Chocolate) P/N 08Z13-SZA-140B
More informationCompanion Service Guide
Companion Service Guide This Service Guide contains: Troubleshooting Replacement Instructions Contact Information Golden Technologies 401 Bridge Street Old Forge, PA 18518 Toll-free: 800-624-6374 Fax:
More informationPRODUCT MANUAL - M090
PRODUCT MANUAL - M090 MODEL 203/266 ELECTRIC CAN OPENER 1 SAFETY CAUTION: SEVERED CAN LIDS HAVE CUTTING EDGES. USE OF A PROTECTIVE GLOVE OR TONGS IS ADVISED WHEN HANDLING LIDS. WARNING To avoid risk of
More informationwww.sebury.com.cn Digital Keypad Use s Manual
K3 K4 www.sebury.com.cn Digital Keypad Use s Manual Contents Introduction Introduction Specifications Intramural Interface Circuit 3 Mounting 3 Wiring 5 Power UP 7 Engineer Programming Mode 7 The K3/K4
More informationTREX OUTDOOR LIGHTING TROUBLESHOOTING GUIDE
TREX OUTDOOR LIGHTING TROUBLESHOOTING GUIDE DECK LIGHTING If you re experiencing a problem with any part of the Trex Deck Lighting system, please reference the troubleshooting flow charts below. Most common
More informationHP 16/18-Port Cable Management Kit Installation Guide
HP 16/18-Port Cable Management Kit Installation Guide Abstract This document describes how to attach the HP 16 Port or 18 Port Cable Management Kit to an HP rack. The cable management bracket is designed
More informationCAM-03, Camshaft Assembly Oil Seal Replacement
CAM-03, Camshaft Assembly Oil Seal Replacement Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft Pin Spanner
More informationInstalling the JTAG connector
Installing the JTAG connector IAR KickStart Development Kit for LEGO MINDSTORMS NXT This guide describes how to solder the JTAG connector onto the LEGO MINDSTORMS NXT. This connector and cable will later
More informationAir-Oxygen Blender. Service Manual. Model No. PM5200 Series PM5300 Series (shown)
Service Manual Model No. PM5200 Series PM5300 Series (shown) SAVE THESE INSTRUCTIONS 300 Held Drive Tel: (+001) 610-262-6090 Northampton, PA 18067 USA Fax: (+001) 610-262-6080 www.precisionmedical.com
More informationMODEL D GENERATOR COIL REPLACEMENT
MODEL D GENERATOR COIL REPLACEMENT Materials Needed Procedure concept2.com 800.245.5676 (U.S. & Canada only) 0708 REPLACING THE MOUSE ON THE INDOOR ROWER 0409 TOOLS 5/32 7/16 or 11mm concept2.com 1. 2
More informationGTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com
GTI VR6 Front Wheel Bearing DIY http://www.gtishrine.com This procedure covers replacing the front wheel bearings. Tools and Parts required: Wheel Bearing Puller w/ ABS adapter. Available for rent from
More information31.39 1.69. Determine the desired location fixture and center the coaxial cord location to the electrical box.
Installation Instructions for JORN 00LSJORN_ 90LSJORN.0 GENERAL PRODUCT I NFORMATION: This product is suitable for indoor dry locations only. CAUTION RISK OF FIRE This product requires installation by
More informationD I G I T A L C L A M
T h e M A X X P r e s s D I G I T A L C L A M O P E R A T O R S M A N U A L 6 x0 x5 5 x5 Folie & Papper Sweden AB Box 90 00 9 Göteborg Telefon 03-9 00 80 Fax 03-9 00 89 www.foliepapper.se Safety Instructions
More informationElectric Landing Gear controllers and sequencer LGC12 / LGC 13C
Electric Landing Gear controllers and sequencer LGC12 / LGC 13C Users Guide. Torrent d en Puig, 31. 08358, Arenys de Munt, Barcelona,Catalonia,Spain E-mail: info@xicoy.com. Fax: +34 933 969 743 web: www.xicoy.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationFX Circuit Board Replacement Instructions
FX Circuit Board Replacement Instructions There are three circuit boards inside the FX inverter. Normally, only two of these boards are candidates for replacement; the FET board (large board that includes
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
More informationFirmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual
Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS
More information!"#$%&'()*#%+!,-./ 011-2,.%34$5')4564%7"&8*# 9%8:;<%0<17%&=&2$'#)=
!"#$%&'()*#%+!,-./ 011-2,.%34$5')4564%7"&8*# 9%8:;
More informationCompliments of SwatchBattery.com
Compliments of SwatchBattery.com Tools Y O U W I L L N E E D Case Holding Vise Case Knife Fine-point Tweezers Plastic Tweezers Small Screwdriver EWB-1 Battery Tester Case Wrench Watch Closing Hand Press
More informationInstalling RNS-E SAT NAV for Audi A4
As one of the major options on the A4 you can get a DVD Satellite Navigation System call the RNS-E. With the help of ebay these sat nav systems are now available to by at a rough cost of 650 plus the cost
More informationUPPER TENSION MECHANISM - (66 & 99 models)
UPPER TENSION MECHANISM - (66 & 99 models)..006 The principals of thread tension have already been covered in the section on How a Sewing Machine Works page [] E - 4. () The majority of tension adjustments
More information2M IR Mini Dome Quick Installation Guide
2M IR Mini Dome 2M IR Mini Dome Quick Installation Guide Please follow the installation steps below to set up 2M IR Mini Dome IP Camera. Check the package contents against the list below. See P.1 Physical
More informationSpreader Light Bulb Replacement Instructions
Spreader Light Bulb Replacement Instructions IMPORTANT: DISCONNECT LIGHT FROM BATTERY BEFORE PROCEEDING. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR OTHER DAMAGE. Tools Needed You will need the following
More informationCleaning Instructions for Burner, Pilot Assembly, and Emitter Screen Series: 220000-450000
Cleaning Instructions for Burner, Pilot Assembly, and Emitter Screen Series: 220000-450000 10 mm open end wrench 12 mm open end wrench 9/16 open end wrench 5/8 open end wrench 11/16 open end wrench 9/16
More informationBrief introduction----------------------------------------------------------------------------03
A-1 skyraider Brief introduction----------------------------------------------------------------------------03 Specification----------------------------------------------------------------------------------03
More informationTrillium 40 Axis Spring Tensioner Wire Replacement Instructions
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer
More informationTraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions
TraceTek TTDM Series Leak Detection and Location Modules Replacement Parts Installation Instructions TRACETEK TraceTek TTDM Replacement Parts General Information These instructions detail the steps to
More informationRain+Birdt. Simple To Set Timer (SST) Setup & Operation Instructions. English. 1-800- RAIN BIRD (800-724-6247) or visit www.rainbird.
Rain+Birdt Simple To Set r (SST) Setup & Operation Instructions English Installation...2 Tools and Supplies Needed...2 Step 1. Mount r...2 Step 2. Connect Power...2 Indoor r...2 Outdoor r...2 Step 3. Connect
More informationExpress5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001
Express5800/120Ed Rack Mount Kit Installation Procedures PN: 455-01607-001 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,
More informationTABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
More informationInstallation Instructions
520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
More informationNavico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement
Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations
More informationReplacing N-300 PCB. 2014 YZ Systems for use by YZ s distribution network and end-users. www.yzsystems.com
Replacing N-300 PCB Replacing N-300 PCB Record all Parameters and other operational information from The N-300 if Possible for Use in Programing The new PCB. If Parameters are not Obtainable from The Old
More informationDishmachine Component Maintenance Instructions. Drain Solenoid Replacment. Conserver XL Conserver XL2 Conserver XL2-CML Conserver XL2-CMR
Dishmachine Component Maintenance Instructions Drain Solenoid Replacment Conserver XL Conserver XL2 Conserver XL2-CML Conserver XL2-CMR 07610-003-08-60 A July 2, 2005 The dishmachines of the Conserver
More informationCPL SYSTEMS / GROENEVELD AUTOMATIC GREASING SYSTEM COMPLETE SYSTEM CHECK PNEUMATIC PUMP
CPL SYSTEMS / GROENEVELD AUTOMATIC GREASING SYSTEM COMPLETE SYSTEM CHECK PNEUMATIC PUMP Feb 5, 2003 1 CPL SYSTEMS / GROENEVELD AUTOMATIC GREASING COMPLETE SYSTEM CHECK - PNEUMATIC PUMP THE SYSTEM DOES
More informationEXPLORE 4-Leg Teaming Table with Screen Share Assembly Instructions
EXPLORE 4-Leg Teaming Table with Screen Share Monitor Display Requirements: your flat panel display must confirm to the following requirements. y With the stand removed, the monitor must not exceed 40
More information40-6680 5 Beam Laser Pointer Service Manual
40-6680 5 Beam Laser Pointer Service Manual Contents Item Description Pages 1.0 Introduction 2 2.0 Overall Instrument Dis-assembly 2 2.1 Body module Dis-assembly 3 2.2 Core Module Dis-Assembly 4-5 2.3
More informationInstallation instruction do88 Intercooler for Volvo S40 / V50 / C30
Installation instruction do88 Intercooler for Volvo S40 / V50 / C30 This instruction shows how to replace the OEM intercooler with our performance intercooler. 2. 3. 1. 4. 5. Part number: ICM-170 6. At
More information