Do-It-Yourself Landscape Ideas. Wall Systems Pavers Patio Stones Edgers

Transcription

1 Do-It-Yourself Landscape Ideas Wall Systems Pavers Patio Stones Edgers

2 Landscaping Ideas & Products Anchor Block Company, a leader in landscape 4 14 products and a licensed manufacturer of Anchor Wall Systems products, continually invents stylish ways to help homeowners improve their outdoor spaces Rear lip No pins. No mortar. No misalignments. Rear-lip block, invented by Anchor, makes installation fast and accurate. Anchor the original rear-lip product! 6 9 2

3 Table of Contents Wall Systems... 4 Fire Pit Kits Pavers Patio Stones Edgers...14 Planning & Installation Colors shown in this brochure may vary from actual product colors. Check store for actual sample color. Some products and colors may not be available in all locations. Check with your local retailer. Cover photo: Fresco square fire pit kit, Fresco pavers and wall system, Northwoods color. 3

4 Wall Systems Ashlarstone TM Retaining Wall Total Wall Height: Build up to 24" Inspired by the traditional random-course design of hand-chiseled stone. Cap Size: 2"H x 12"L x 8"D Cap Weight: 14.7 lbs. Block Size: 4"H x 12"L x 7"D Block Weight: 23.4 lbs. Rear lip makes installation easy stack and align Tan/Brown Carlton Retaining Wall Total Wall Height: Build up to 24" The rugged texture of this compact block makes it ideal for smaller projects. Block Size: 3"H x 10"L x 5 7 8"D Block Weight: 11.3 lbs. Solid Color: Rear lip makes installation easy stack and align Majestic Gray Tan 4

5 Aspen Stone Retaining Wall Total Wall Height: Build up to 24" The rough-hewn texture and blended colors provide a pleasing stone appearance. Cap Size: 3 3 8"H x 12"/9"L x 7 1 2"D Cap Weight: 14.7 lbs. Block Size: 4"H x "L x 7"D Block Weight: 23.4 lbs. Blended Colors: Solid Colors: Rear lip makes installation easy stack and align Red/Charcoal Sand Charcoal Desert Tan Windsor Stone Retaining Wall Total Wall Height: Build up to 24" This traditional face style gives any garden wall a timeless appearance. Cap Size: 3 3 8"H x 12"/9"L x 7 1 2"D Cap Weight: 14.7 lbs. Block Size: 4"H x "L x 7"D Block Weight: 23.4 lbs. Blended Colors: Solid Colors: Rear lip makes installation easy stack and align Brown/Buff Tan/Gray Charcoal Desert Tan Gray 5

6 Wall Systems Diamond 10D Retaining Wall Total Wall Height: Build up to 42" The Diamond 10D retaining wall system has the dependability of the original Diamond product, but with through-cores for a lighter weight and ease of handling. Block Size: 6"H x "L x 10"D Block Weight: 57 lbs. NEW Solid Colors: Rear lip makes installation easy stack and align Brown/Buff Desert Tan Gray ShortCut Cap Straight Walls W N W N W N W N N W N W N W N W This double-faced, tapered cap is ideal for straight or curved walls. Sized to minimize cutting Alternate narrow (N) / wide (W) faces every other cap for straight walls Place all narrow (N) faces on one side for curved walls Cap Size: 3"H x 8"/7"L x 13"D Cap Weight: 23 lbs. W Wide face W N W N Curved Walls N N W W N W N N W W N Narrow face Colors: See Diamond 10D swatches above 6

7 Hampton Stone Retaining Wall Total Wall Height: Build up to 42" This attractive block has a roughhewn appearance softened by rounded edges. Block Size: 6"H x 16"L x 10"D Block Weight: 55 lbs. Rear lip makes installation easy stack and align Sand Hudson Stone TM Fire Pit Kitre Pit Kit The Hudson Stone fire pit kit features a rough-hewn face texture and is conveniently packaged with: 42 Hudson Stone tapered units A sturdy 28" metal liner Outside diameter: 40" Inside diameter: 28" Height: 12" Pallet Weight: 620 lbs. Sand 7

8 Wall Systems and Pavers Fresco TM Wall System Fire Pit Kits Enhance your outdoor living and create a warm focal point for your outdoor enjoyment. Fresco TM Circle Fire Pit Kit Outside diameter: 52" Inside diameter: 35" Height: 12" Blended Colors: The components of the Fresco wall system are versatile and can be oriented in any manner to create small retaining walls, freestanding walls and outdoor projects. Rectangle Block Size: 4"H x 12"L x 8"D Block Weight: 30 lbs. Tapered Block Size: Front: 4"H x 8 5 8"L x 8"D Back: 4"H x 6"L x 8"D Block Weight: 18 lbs. Blended Colors: Mahogany Northwoods For project ideas: scan with your mobile device or visit anchorblock.com/products/walls/ fresco-wall-system/default.aspx With a time-worn appearance, the Fresco circle fire pit kit is conveniently packaged with: 57 Fresco tapered blocks A sturdy 35" metal liner Pallet Weight: 1,133 lbs. Mahogany Northwoods Removable cooking grate sold separately for both Fresco fire pit kits. NEW Fresco TM Square Fire Pit Kit Outside dimension: 44" Inside dimension: 28" Height: 16" 8 With a time-worn appearance, the Fresco square fire pit kit is conveniently packaged with: 48 Fresco rectangular blocks A sturdy 28" x 28" metal liner Pallet Weight: 1,457 lbs. Northwoods

9 NEW Fresco TM Pavers With a smooth surface and time-worn appearance, the Fresco pavers are suitable for patios, walkways and driveways. Northwoods Large Rectangle Unit Size: 8 3 4"W x "L x 2 3 8"H Weight: 20 lbs. Square Unit Size: 8 3 4"W x 8 3 4"L x 2 3 8"H Weight: 15 lbs. Medium Rectangle Unit Size: 8 3 4"W x 5 7 8"L x 2 3 8"H Weight: 10 lbs. 9

10 Pavers Slate Top TM Pavers Create a beautiful patio or walkway that has the look of real slate without the work of installing natural stone. Charcoal/Tan Rectangle Unit Size: 5 1 2"W x 8 1 4"L x 2 3 8"H Weight: 9 lbs. Square Unit Size: 5 1 2"W x 5 1 2"L x 2 3 8"H Weight: 6 lbs. Holland Pavers A timeless product that is versatile for many applications. Install with one of three paver patterns shown on page 17 or use as a soldier course. Unit Size: 3 7 8"W x 7 7 8"L x 2 3 8"H Weight: 6 lbs. Blended Colors: 10 Autumn Blend Charcoal/Tan Fieldstone Red/Charcoal Tan/Brown

11 Choose the Circle Kit for an instant patio area For planning and installation: Scan with your mobile device or visit pdf/dutch_cobble_circle_kit_ Pallet_Sheet.pdf Dutch Cobble Pavers Autumn Blend Beautiful pavers that bring a warm cobblestone feel to patios, walkways or driveways. Select from four patterns (on page 17) to get the look you want. Rectangle Unit Size: 5 1 2"W x 8 1 4"L x 2 3 8"H Weight: 9 lbs. Square Unit Size: 5 1 2"W x 5 1 2"L x 2 3 8"H Weight: 6 lbs. 11

12 Patio Stones A 40" walkway pattern " Blended Colors: Charcoal/Tan 40" Rotate each set Autumn Blend Size: Various Sizes x 1 3 4"H Average Weight: 37.3 lbs. Foot Notes Patio Stones Solid Color: Tan This amazing product provides the look of genuine flagstone with easy, streamlined installation because, unlike real flagstone, these stones are smooth on the bottom and have a uniform height eliminating leveling issues as you create stepping paths, walkways and patios. Tan/Brown Cobblestone Patio Stones Cobblestone Random Cobblestone Blended Colors: Charcoal/Tan Tan/Brown Size: 16"W x 16"L x 2"H Weight: 38 lbs. 12

13 Slate Top TM Patio Stones A rugged, textured top simulates the look of real slate while the smooth, even bottom and uniform height make it easy to level and install. Size: 16" W x 16"L x 2"H Weight: 38 lbs. Size: 12" W x 12"L x 2"H Weight: 22 lbs. Charcoal/Tan Blended Colors: Tan/Brown Charcoal/Tan 12" Square Patio Stones Size: 12"W x 12"L x 2"H Weight: 24 lbs. Solid Colors: Red 16" Square Patio Stones Size: 16"W x 16"L x 2"H Weight: 38 lbs. Solid Color: Gray Gray 16" Round Patio Stones Brickface Patio Stones Size: 16" Diam. x 2"H Weight: 34 lbs. Size: 16"W x 16"L x 2"H Weight: 38 lbs. Solid Colors: Copper Exposed Aggregate Red 13

14 Edgers Rivers Edge TM Edgers Rivers Edge TM edgers blend gracefully and naturally into any environment. Great for borders and pathways, their sculpted surface emulates the look of natural stone. Block Size: 3 5 8"W x 12"L x 3 5 8"H Block Weight: 12 lbs. Tan/Brown Anchor Edger Edgers The clean lines of the Anchor Edge edger add bold symmetry to curved borders. Block Size: 4"W x "L x 3"H Block Weight: 10.5 lbs. Blended Colors: Charcoal/Tan Red/Charcoal Tan/Brown Solid Colors: Cambray Tan Charcoal Red 14

15 1. Stake Out Remove Sod 2. Prepare Base 3. Lay & Level Edger Units 4. Cut Edger Units Minimum Outside Diameter: 72" Approx. 6' Edger/Patio Stone Installation Do it yourself Edger Installation 1. Begin by laying out the project using stakes and string line or garden hose (great for curves). Dig a trench 6" wide by 4" deep. 2. Smooth the bottom of the trench. Place 1" of paver base in the bottom of the trench and firmly compact. 3. Position edgers end to end in the trench. Using a rubber mallet, tamp the edgers firmly into place. Use a carpenter s level to ensure your project is level. 4. Edgers can be easily cut to fit your project by using a circular saw with a masonry blade or a hammer and chisel. Read and understand the operating manual before using a saw. How Many EDGERS Do I Need? Curved Applications Pcs. Diameter Pcs. Diameter Pcs. Diameter Pcs. Diameter 18 = 72" 21 = 84" 24 = 96" 27 = 108" 19 = 76" 22 = 88" 25 = 100" 28 = 112" 20 = 80" 23 = 92" 26 = 104" 29 = 116" 36" Minimum Radius 1. Lay Stakes & String Line 2. Prepare and Compact Base 3. Screed Sand 4. Lay Patio Stones 5. Install Edging 6. Fill Joints Do it yourself Patio Stone Installation See page 17 for Calculation Tips 1. Begin by laying out the project using stakes and string line. Add 6" to the perimeter of the finished patio. Mark and remove sod. Excavate area to a depth of 7". 2. Install paver base and thoroughly compact to a finished depth of 4". Use a landscaper s rake to remove any high spots, fill in low spots and compact. Repeat as necessary. 3. Lay two 1" diameter pipes parallel on base. Spread 1" of play sand over compacted base. Screed the play sand by dragging a 2" x 4" board over pipes. Remove pipes and fill voids with sand. 4. Lay patio stones in the desired pattern. If the pattern requires cutting, patio stones can be cut using a circular saw with a masonry blade. 5. Place edging around entire project 3" from edge of compacted aggregate. Install edging and spikes according to the manufacturer s instructions. 6. Fill joints by sweeping additional play sand over the patio. Remove remaining play sand from the top of the project. If using the Foot Notes patio stone, polymeric joint sand may be substituted for play sand to inhibit weed growth between stones. Read and understand the operating manual before using a saw. Circle MATERIALS & TOOLS NEEDED 1. Gloves 2. Circular Saw 3. Shovel 4. String 5. Chisel 6. Level Curves 7. Stakes 8. Safety Glasses 9. Rubber Mallet 10. Paver Base 11. Hand Rake MATERIALS & TOOLS NEEDED (Some tools are available to rent. Not all tools are required for all projects.) 1. Gloves 2. Hammer 3. Chisel 4. Paver Base 5. Tamper 6. Safety Glasses 7. Play Sand 8. Level 9. Stakes 10. Rake 11. Edging String 12. 1" Pipes 13. Spikes 14. Plate Compactor 15. Shovel 16. Polymeric Joint Sand 17. Circular Saw 15

16 Planning Paver Projects 1. Select a shape for your paver project: A 12' E 4' Do it yourself Paver Installation D 8' B 8' RECTANGLE J 8' F 4' G 4' L-SHAPED H 4' 1. Remove Sod 1. Excavate the installation area to approximately 6" larger on all sides than the actual finished size. C 12' 2. Plan the dimensions of your finished project, accurate to one inch. 3. Calculate the area (total square feet) of your project. This will determine the total amount of pavers, base material, and play sand that you will need: Rectangle x = square feet A B Example: 12' x 8' = 96 square feet L-Shaped: ( x ) = ( x ) = + = square feet E F K H I L K L Example: (4' x 4' ) = 16' (4' x 8' ) = 32' 16' + 32' = 48 square feet 4. Compute the perimeter to determine edging and/or border quantity: Rectangle: = linear feet A B C D Example: 12' + 8' + 12' + 8' = 40 linear feet L-Shaped: = linear feet E F G H I J Example: 4' + 4' + 4' + 4' + 8' + 8' = 32 linear feet I 8' 2. Prepare and Compact Base 3. Screed Sand 4. Lay Pavers 2. Install paver base to a compacted finished thickness of 4-6" for patios and walkways and 8-12" for driveways. Paver base should be installed in 2" increments and thoroughly compacted. The final grade should slope away from the house, dropping 1 /4" per foot for drainage. 3. Lay two 1" diameter pipes parallel on base. Spread 1" of play sand over compacted base. Screed the play sand by dragging a 2" x 4" board over pipes. Remove pipes and fill voids with sand. 4. Lay pavers in the desired pattern. If the pattern requires cutting, the pavers can be cut with a circular saw using a masonry blade. 5. Select your Anchor TM paver product and pattern; then calculate the number of pavers needed using the dimensions provided. 6. Determine the amount of paver base material necessary. Minimum 4-6" deep for paths and patios, 8-12" for driveways Square feet of project x 0.09 (1" deep) = cubic feet of paver base. 7. Calculate the amount of play sand needed over the base and between joints. Square feet of project x 0.09 (1" deep) = cubic feet of sand (add approximately a half cubic foot per 100 square feet of pavers for joints). 8. Compute the required quantity of edge restraint & spikes. 9. Figure the total cost of your project (on the next page). 5. Install Edging 6. Compact/ Spread Sand 5. Install e dging and spikes around the entire project according to the manufacturer s instructions. Install paver edge 6" from edge of compacted aggregate. 6. Compact the installed pavers with a plate compactor in both directions with at least two passes. Once compacted, spread play sand on the pavers and sweep into joints. Compact again to ensure that all joints are completely full. Repeat as necessary. Sweep off remaining sand from pavers. 16 Substitute polymeric joint sand in place of play sand to inhibit weed growth between pavers. Read manufacturer instructions. Read and understand the operating manual before using a saw. Snow and Ice Removal: To maintain the best surface integrity, use plastic blades on snow plow and raise blades on snow blower. Do not use sharp objects to chop ice as they can damage the surface.

17 Paver Project Costing Worksheet # of Pavers Needed X $ = $ Paver Base Material* X $ = $ Play Sand X $ = $ Edging X $ = $ Spikes X $ = $ Tool Rental X $ = $ Delivery $ Estimated Total Project Cost $ *Must be converted from cubic feet to bags. MATERIALS & TOOLS NEEDED (Some tools are available to rent. Not all tools are required for all projects.) Gloves Shovel String Chisel Level Stakes Safety Glasses Hammer Rubber Mallet Tamper Pipes Edging Spikes Tub Saw Paver Base Play Sand Plate Compactor Patterns for Holland Pavers Patterns for Slate Top TM Pavers & Dutch Cobble Pavers Patterns for Fresco TM Pavers Running Bond Herringbone Parquet 1:1 Running Bond 1:1 Random 3:1 Running Basket Weave Bond 1:1:1 Random 1:2:1 Random Approximate Stones Needed for Projects Slate Top TM Pavers & Dutch Cobble Pavers 12" x 12" 5 Pieces Holland 1:1 Running Bond 16" x 16" Foot Notes 3:1 Running Bond Basket Weave Pavers or 1:1 Random Patio Stones Patio Stones* Pieces Squares Rectangles Squares Rectangles Squares Rectangles Pieces Pieces Fresco TM Pavers 1:1:1 Random 1:2:1 Random Large Medium Large Medium Square Rectangle Rectangle Square Rectangle Rectangle 10' 10' 100 sq.ft Sets ' 150 sq.ft. 10' Sets ' 12' 240 sq.ft. 1, Sets ' 400 sq.ft. 20' 1, , Sets ' 2' 40 sq.ft Sets ' 4' 80 sq.ft Sets Coverage: 4.6 pcs. / sq. ft. Squares = 4.76 pcs./sq. ft. and Rectangles = 3.17 pcs. / sq. ft pcs. / sq. ft. *Not 0.45 sold pcs. as / sq. a set ft pcs. / sq. ft. Go to for our online paver calculator and visualizer. 17

18 Planning Wall Projects Choose your retaining wall block and color, then: 1. Estimate the number of courses of block in your finished wall including base course. 2. Determine number of blocks needed by multiplying the total number of blocks per course times the number of courses. Length of wall in inches X Height of wall in inches = Total square inches = Total square inches divided by 144 = square feet of wall Divide wall square feet: by 0.33 for Ashlarstone product = blocks. by 0.33 for Aspen Stone product = blocks. by 0.21 for Carlton product = blocks. by 0.74 for Diamond 10D product = blocks. by 0.33 for Fresco product = blocks. by 0.66 for Hampton Stone product = blocks. by 0.33 for Windsor Stone product = blocks. 3. Determine the total cubic feet of base material needed by multiplying the number of linear feet of wall times 0.4 cubic foot. This will give you a 4" deep base, 14" wide. Please refer to specific product information for recommended base depth. Total wall linear ft. x 0.4 cubic foot = total cubic ft. base material. Example: 10 linear feet of wall x 0.4 cubic foot = 4 cubic feet base material. (1 cubic foot = 120 lbs.) 4. Calculate the amount of drainage aggregate that you ll need behind the wall. Total linear ft. of wall x height x 1.0 cubic foot = total cubic feet of drainage aggregate. This will give you 12" of drainage aggregate behind the wall. Example: 10 ft. long x 2 ft. high x 1.0 = 20 cubic feet of drainage aggregate behind the wall. (1 cubic foot = 120 lbs.) Reference charts indicating number of blocks needed Ashlarstone TM / Aspen Stone /Windsor Stone Hampton Stone Carlton WALL HEIGHT WALL LENGTH 5' 10' 15' 20' 25' 30' 1 Course Courses Courses Courses Courses Courses CAPS WALL LENGTH 5' 10' 15' 20' 25' 30' Ashlarstone Qty Aspen Stone/Windsor Stone Qty WALL HEIGHT ShortCut CAPS Diamond 10D WALL LENGTH 5' 10' 15' 20' 25' 30' 1 Course Courses Courses Courses Courses Courses Courses WALL LENGTH 5' 10' 15' 20' 25' 30' Quantity for straight wall Quantity for curved wall WALL HEIGHT WALL LENGTH 5' 10' 15' 20' 25' 30' 1 Course Courses Courses Courses Courses Courses Courses WALL HEIGHT Fresco TM WALL LENGTH 5' 10' 15' 20' 25' 30' 1 Course Courses Courses Courses Courses Courses Fresco TM CAPS* See ShortCut Cap quantity WALL LENGTH 5' 10' 15' 20' 25' 30' Quantity needed * 8" width faced forward as pictured on cover. WALL LENGTH WALL HEIGHT 5' 10' 15' 20' 25' 30' 1 Course Courses Courses Courses Courses Courses Courses Courses See Aspen Stone /Windsor Stone Cap quantity Do it yourself Fresco TM Wall Installation See Retaining Wall Installation on page 19 except note the following differences. Step 4: No need to remove rear lips or use as alignment in building wall. Eliminate Step 5. Fresco TM wall block can be used as a cap, if desired. Use exterior-grade concrete adhesive to secure each block in the top two rows. 18 Quantity calculations are rounded up to the next block. Product dimensions may vary or change without notice. The number of caps needed is based on straight walls, unless otherwise noted additional caps may be required for curved walls.

19 Installing Your Wall Project 1. Stake Out/Remove Sod 2. Add & Compact Gravel 3. Level Base 4. Lay and Level Blocks 5. Add Drainage Aggregate 6. Split/Cut Block 7. Mark & Cut Cap 8. Glue Cap Do it yourself Retaining Wall Installation For Fresco TM Wall System see page Begin by laying out the wall. Use stakes with a string line or a garden hose (excellent for curved walls) to mark the location of the back of the wall. Use the information below to determine the size of the trench needed, and then dig the trench. The width of the trench should be twice the depth (front to back) of the block. For block that is 4 inches deep make the trench 8 inches wide. For block that is 5.5 inches deep make the trench 11 inches wide. For block that is 6 inches deep make the trench 12 inches wide. For block that is 7 inches deep make the trench 14 inches wide. For block that is 12 inches deep make the trench 24 inches wide. Trench depth: Make the trench deep enough to bury a full block of the first course plus 6 inches of base material. Example: for 6-inch-high block, dig a trench 12 inches deep. If the property slopes, start the trench at the lowest point and step the trench up or down as necessary, making sure that at least half of the first course block will be buried. 2. Remove loose soil and firmly compact the soil in the bottom of the trench with the tamper. Add a layer of base material in the bottom of the trench; rake out and firmly compact. Base material can be paver base or an equivalent to 3 /4-inch minus (with fines) aggregate. Use the appropriate amount of base material for the height of the wall you are building. 3. Use a carpenter s level to level base material from front to back and side to side; check the level every few feet. Add more base material and repeat process as needed until appropriate base depth is achieved. The more level the base material, the easier it is to level the block when building the wall. 4. Use a hammer and chisel to remove the rear lips from all blocks for the first course. Position the individual blocks side by side on the prepared base so that front edges of the block are touching and the back edge aligns with the string line. Level block in both directions, adjusting with the rubber mallet if necessary. Begin next course by laying a block with the rear lip facing down, in a staggered relationship to the course beneath (running bond). Pull each block forward until the lip is securely in contact with the blocks below. Check each course for level before continuing and make adjustments with rubber mallet. Repeat the process until the desired wall height is reached. 5. Place filter fabric directly behind the wall extending from the bottom of the first course to the middle of the top course. Fill behind each course with drainage aggregate (such as 3 /4-inch free draining) that extends 12 inches behind the wall. Fill cores of blocks (if applicable). Compact aggregate with tamper. Organic soil or clay-type soil is not recommended for backfill material. 6. Cutting or splitting blocks may be required for your project. To split a block: Use a hammer and chisel to score the block on all sides. Pound the chisel on the score line until the block splits. To cut a block: Use a circular saw with a masonry blade. To cut a 90-degree mitered corner: Use a circular saw with a masonry blade. Cut a 45-degree angle on two blocks. Glue cut sides together with exterior grade concrete adhesive so the two faces form the finished outside corner. 7. To cap the wall, slide the cap forward so the face of the cap overhangs the face of the wall approximately 1 inch. For capping curves, trim the caps to follow the radius of the wall. Place a cap at the beginning of the curve, skip a space and place the next cap in the third position. Rest a cap on top of the original two, aligning the face with the adjacent caps. Mark the bottom of the cap along the edges (as shown in illustration 7). Use a circular saw with a masonry blade to cut the marked cap. On a 90-degree corner, two caps need to be saw-cut to achieve a 45-degree mitered corner. At the end of the wall, cut the cap so the manufactured edge is exposed and the cut edge is against the next cap. 8. Use an exterior-grade concrete construction adhesive to secure the caps. Always wear eye protection when splitting blocks. Read and understand the operating manual before using a saw. MATERIALS & TOOLS NEEDED Gloves Circular Saw Shovel String Chisel Level Stakes Safety Glasses Hammer Base Material Hand Rake Filter fabric Tamper Adhesive Drainage Aggregate 19

20 Anchor Block Company, 5959 Baker Road, Suite 390, Minnetonka, MN Ph Anchor Block Company. Anchor Block Company manufactures the retaining wall systems described in this document under license from Anchor Wall Systems, Inc. The logos, slogans, product names and other trademarks shown in this document are trademarks of Anchor Wall Systems, Inc. or Anchor Block Company. Anchor Block Company s complete line of walls, pavers and edgers is locally made in Minnesota. Products manufactured by Anchor Block Company are covered by a limited warranty and are subject to Terms and Conditions of sale. Visit to see the full text of that limited warranty /14