CALL: (09) GENOA FLOOR MOUNT CLAMP LUGANO FACE FIX CLAMP MONACO FLOOR MOUNT CLAMP EUROANCHOR DISCS & SPACERS

Transcription

1 BALUSTRADE & POOL: INDEX MONTREUX FLOOR MOUNT CHANNEL GENOA FLOOR MOUNT CLAMP LUGANO FACE FIX CLAMP MONACO FLOOR MOUNT CLAMP EUROANCHOR DISCS & SPACERS MILANO EUROPOSTS EUROBRACE & MINIPOSTS HANDRAILS BRACKETS & CLAMPS VIENNA HYDRAULIC HINGE & LATCH POOL GATE DOOR PIVOTS B2 - B3 B4 - B5 B6 - B7 B8 - B9 B10 - B17 B18 - B25 B26 - B27 B28 B29 - B30 B31 - B32 B33 catalogue effective 1st june 2015 B1

2 MONTREUX MONTREUX Residential Floor Mount Channel EDC Mill finish Silver Pearl powdercoat Selected powdercoat, lead time applies 1.25m, 2.5m and 5m stock lengths Supplied complete with clamping kits and cover plates Vertical adjustment up to 15mm Out of plumb adjustment: +/- 1000mm high +/- 1200mm high M10 coach screw at 200mm centres fixing in timber M10 s/s epoxy bolts at 400mm centres fixing in concrete and steel Clamping kits no greater than 400mm centres Supporting base channel is anotec powder-coated with 10yr warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Based on barrier loads from AS/NZS Viridian 12mm toughened or 13.5mm toughened laminated safety glass Very high wind zone 1.76 kpa or less Maximum heights above floor level are: For Residential Occupancies A & C3 of Table 3.3 AS/NZS mm from finish floor level 1200mm with glass corners at the top connected by Euroglass balustrade clamps, or an interlinking handrail at 900mm to 1000mm End panels must be connected to the building by clamps or interlinking rail Suitable for pool fencing protecting a fall of 1 metre or more Refer to our website for further details EDCEND End Cap 100mm 25mm glass clearance 12mm 89mm R mm 25mm Concrete fixing Glass Cut Out Detail B2

3 MONTREUX MONTREUX Residential Floor Mount Channel EDC Timber fixing Steel fixing B3

4 GENOA GENOA Commercial Floor Mount Clamp EYB Mill Silver Pearl powdercoat Selected powdercoat, lead time applies 1.2m, 2.4m and 4.8m stock lengths SETS available for the different fixing options: Concrete fix Steel fix Suitable for 15mm toughened and 17.5mm laminated glass Recommended installation tools available End caps available Glass cut out required 10 year warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Based on design loads from AS/NZS and a max. uls wind pressure of 2.13 kpa (extra high wind zone), minimum glass thicknesses are: For commercial occupancies B, E and C3 of Table 3.3 AS/NZS : Up to 1100mm high balustrade measured from floor level Viridian Balustrade mm toughened safety glass or 17.5mm laminated toughened glass Refer to our website for further details Glass notch Steel fixing B4

5 GENOA GENOA Commercial Floor Mount Clamp EYB Concrete fixing Single concrete fixing plate B5

6 LUGANO LUGANO Residential Face Fix Channel EFC Mill Silver Pearl powdercoat Selected powdercoat, lead time applies 1.2m, 2.4m and 4.8m stock lengths SETS available for the different fixing options: Concrete fix Steel fix Bolt through timber fix Lag screw Suitable for 12mm toughened and 13.5mm laminated glass Recommended installation tools available End, internal and external corner caps available No glass cut outs or holes required 10 year warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Based on barrier loads from AS/NZS , Viridian 12mm Balustrade 100 toughened safety glass or 13.5mm toughened laminated safety glass, maximum height above the channel is: For Residential Occupancy A, B, C3 of Table 3.3 AS/NZS Very high wind zone 1.76 kpa or less: 1200mm high with glass corners at top edge connected by Euroglass balustrade clamps or with an interlinking rail at 900mm to 1000mm End panels must be connected to the building by clamps or interlinking rail Extra high wind zone 2.13 kpa or less: 1100mm high without balustrade corner clamps or interlinking rail Suitable for pool fencing protecting a fall of one metre or more Refer to our website for further details Concrete fixing Timber slatted deck bolt-through fixing B6

7 LUGANO LUGANO Residential Face Fix Channel EFC Timber slatted deck lag screw fixing Timber enclosed deck lag screw fixing Steel fixing external & internal Steel fixing internal B7

8 monaco MONACO Commercial Face Fix Clamp EGL Mill Silver Pearl powdercoat Selected powdercoat, lead time applies 1.2m, 2.4m and 4.8m stock lengths SETS available for the different fixing options: Concrete fix Steel fix Bolt through timber fix Suitable for 15mm and 19mm toughened and 17.5mm and 21.5mm laminated glass Recommended installation tools available End, internal and external corner caps available Glass cut-out required 10 year warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Based on design loads from Table 3.3 of AS/NZS and a max. uls wind pressure of 3.0 kpa, minimum glass thicknesses and max balustrade heights measured from top of clamp are: Occupancy B, E & C3 Viridian Balustrade mm toughened safety glass or 17.5mm toughened laminated safety glass up to 1200mm Occupancy C1/C2 & D: Viridian Balustrade mm toughened safety glass up to 1100mm with corner connectors, or Viridian Balustrade mm toughened safety glass or 21.5mm laminated toughened glass up to 1200mm Refer to our website for further details Glass notch Concrete fixing B8

9 monaco MONACO Commercial Face Fix Clamp EGL Timber slatted deck Steel fixing B9

10 EUROANCHOR STEPPED DISCS EUBFSD50/51 Euroanchor 50mm stepped disc EUBFSD50 includes 25mm thick spacer / EUBFSD51 includes 10mm thick spacer Satin anodised Manufactured in 316 grade stainless steel Anodised to over 20 µm The substrate material can be concrete, steel or timber Includes washer, PVC sleeve & fixing (please specify either lag screw or threaded rod) Glass fixing hole 26mm dia 25mm spacer can be threaded M10 or 10.5mm through hole (specify upon order) Fixing centres as per PS1 PS1 available on request for use with Viridian Balustrade 100 toughened safety glass EUBFSQ Euroanchor 50mm square stepped disc Manufactured in 316 grade stainless steel The substrate material can be concrete, steel or timber Includes washer, PVC sleeve & fixing (please specify either lag screw or threaded rod) Glass fixing hole 26mm dia Fixing centres as per PS1 PS1 available on request for use with Viridian Balustrade 100 toughened safety glass EUBFCS Euroanchor 50mm countersunk stepped disc Manufactured in 316 grade stainless steel The substrate material can be concrete, steel or timber 10mm and 25mm spacers available Includes washer, PVC sleeve & fixing (please specify either lag screw or threaded rod) Glass fixing hole 22mm dia 25mm spacer threaded M10 M10 x 35 countersunk hex bolt Fixing centres as per PS1 PS1 available on request for use with Viridian Balustrade 100 toughened safety glass 10 EUBFSQD Euroanchor rectangular stepped disc Manufactured in 316 grade stainless steel The substrate material can be concrete, steel or timber Double 25mm spacer 10.5mm through hole Includes washer, PVC sleeve & fixing (please specify either lag screw or threaded rod) Glass fixing hole 26mm dia Fixing centres as per PS1 PS1 available on request for use with Viridian Balustrade 100 toughened safety glass B10

11 EUROANCHOR STEPPED DISCS EUROANCHOR Residential Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD For Residential ccupancies A, B, C3 of Table 3.3 AS/NZS Based on 12mm Viridian Balustrade 100 toughened safety glass, maximum heights of glass above top anchors for residential occupancies A and C3 of Table 3.3 AS/NZS are: - Very high wind zone 1.76 kpa mm - High wind zone 1.36 kpa mm with corner connectors or interlinking handrail Maximum distance from side edge of glass to fixings is 300mm for occupancy A and 200mm for occupancy C3 10 year warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Concrete fixing Timber slatted deck bolt-through fixing B11

12 EUROANCHOR STEPPED DISCS EUROANCHOR Residential Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD Tapped fixing steel Internal only Steel fixing B12

13 EUROANCHOR STEPPED DISCS EUROANCHOR Residential Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD Timber lag screw Internal only Weatherboard, angle spacer Enclosed deck only B13

14 EUROANCHOR STEPPED DISCS EUROANCHOR Residential Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD Timber fix, cavity cladding Enclosed deck Timber, lag screw fixing Slatted deck B14

15 EUROANCHOR STEPPED DISCS EUROANCHOR Commercial Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD For Commercial occupancies B, E, C3 of Table 3.3 AS/NZS Based on 15mm Viridian Balustrade 100 toughened safety glass, maximum heights of glass above top anchors for commercial occupancies B, E, C3 of Table 3.3 AS/NZS are: - Extra high wind zone 2.13 kpa mm 10 year warranty PS1 available for use with Viridian Balustrade 100 toughened safety glass Concrete fixing B15

16 EUROANCHOR STEPPED DISCS EUROANCHOR Commercial Balustrade System EUBFSD550/51 EUBFSQ EUBFCS EUBFSQD Timber slatted deck bolt-through fixing Steel fixing B16

17 spacers & stepped discs SP5025T and SP5025 Spacers Satin anodised SP5025T - Threaded M10 hole SP mm dia. through hole Ø50 25 SPC5010 Countersunk disc or Spacer Drilled and countersunk To suit M10 countersunk hex bolt Ø50 10 SD50M10 Stepped disc Satin anodised M10 threaded blind hole Ø50 12 SP505WB Weatherboard shim Satin anodised 8 degree angle 12mm thick tapered to 5mm 10.5mm dia. through hole Ø50 SPG3210/12 Gib spacers Plastic Aluminium 10mm thick plastic or aluminum 12mm thick plastic or aluminium Ø32 10 or 12 B17

18 Milano europost RESIDENTIAL MILANO POST Semi-Frameless Residential Balustrade Posts ERP Silver Pearl powdercoat Selected powdercoat Based on design loads from AS/NZS and a max uls wind pressure of 1.76 kpa (very high wind zone) Rated for Residential occupancy A and C3 Suited for Viridian Balustrade mm toughened safety glass or 11.5mm toughened laminate glass Fixed at 1650mm centres Maximum height 1100mm Maximum glass overhang 500mm PS1 available on request for use with Viridian Balustrade 100 toughened safety glass Refer to our website for further details 500mm max. 500mm max. ERPT Top Fixed Concrete or steel Supplied complete with fixing to suit substrate Four fixings per post Minimum edge distance for fixings is 50mm B18

19 Milano europost RESIDENTIAL MILANO POST Semi-Frameless Residential Balustrade Posts ERPF Face Fixed Concrete, steel or bolt through timber Minimum edge distance for fixings is 60mm Two fixings per post ERPH Concealed Face Fixed Steel or bolt through timber Minimum edge distance for fixings is 30mm Two fixings per post B19

20 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts ECP Silver Pearl powdercoat Selected powdercoat To suit Commercial occupancy B, E and C3 Concrete or bolt through timber Suited for Virdian Balustrade mm toughened safety glass or 11.5mm toughened laminated glass Fixed at 1100mm centres Maximum height 1100mm Maximum glass overhang 500mm PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer to our website for further details 500mm max. 500mm max. B20

21 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts ECPFC To suit Commercial occupancy B, E and C3 Face fixed to concrete substrate ECPFBT To suit Commercial occupancy B, E and C3 Face fixed to timber substrate B21

22 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts ECPTC To suit Commercial occupancy B, E and C3 Top fixed to concrete substrate B22

23 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts (C5) ECPR Silver Pearl powdercoat Selected powdercoat, lead time applies To suit Commercial occupancy C1, C2, D and C5 Concrete, steel or bolt through timber Two fixings per post Suited for Viridian Balustrade mm toughened safety glass or 17.2mm toughened laminated glass Fixed at 1100mm centres Maximum height 1100mm Maximum glass overhang 300mm PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer to our website for further details 300mm max. B23

24 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts (C5) ECPRBT To suit Commercial occupancy C1, C2, D and C5 Face fixed to timber substrate Substrate fixings are concealed ECPRS To suit Commercial occupancy C1, C2, D and C5 Face fixed to steel substrate Substrate fixings are concealed B24

25 Milano europost COMMERCIAL MILANO POST Semi-Frameless Commercial Balustrade Posts (C5) ECPRC To suit Commercial occupancy C1, C2, D and C5 Face fixed to concrete substrate Substrate fixings are concealed B25

26 EUROBRACE POSTS EB1 Eurobrace Manufactured in 316 grade stainless steel Suitable for 10, 12 and 15mm glass Posts are set into concrete (Ø50mm hole) and affixed using Sika or Rockite grout (to manufacturer s specifications) 26mm diameter holes in glass 45mm typical clearance from ground surface Distance from inside face of glass and post centre is 40mm PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer our website for further details Ø Glass Cut Out Detail EB2 Eurobrace, square 44 Manufactured in 316 grade stainless steel Suitable for 10, 12 and 15mm glass Posts are set into concrete (Ø50mm hole) and affixed using Sika or Rockite grout (to manufacturer s specifications) 26mm diameter holes in glass 45mm typical clearance from ground surface Distance from inside face of glass and post centre is 32mm PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer our website for further details Ø Glass Cut Out Detail B26

27 MINI posts FMP250 Miniposts Manufactured in 316 grade stainless steel Suitable for 12 and 15mm glass Mini posts are set 85mm into concrete (Ø60mm hole) and affixed using sika or rockite grout (to manufacturer s specifications) 26mm diameter hole in glass 45mm typical clearance from ground surface Optional Dress Ring or Cover Plate available PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer our website for further details Ø50 Ø26 FMP250RING 80mm outside dia. 51mm inside dia Glass Cut Out Detail FMP250COVER 125mm outside dia. 51mm inside dia. (matches FMP350 cover) FMP350 Miniposts Manufactured in 316 grade stainless steel Suitable for 12 and 15mm glass 26mm diameter hole in glass 45mm typical clearance from ground surface Posts can be fastened to concrete or wooden surfaces using 2 x M10 bolts/screws PS1 available for use with Viridian Balustrade 100 toughened safety glass Refer our website for further details Ø125 Ø90 PCD 4 holes Ø Glass Cut Out Detail B27

28 HANDRAILS BH1 Slimline handrail & end cap Mill finish Silver Pearl powdercoat Selected powdercoat (lead time applies) Meets AS for handrailing for glass balustrades that are over 1m in height and only fixed to the base Complies with NZS4203:1992 for handrails Suitable for 10mm and 12mm glass (specify when ordering) Can be used for both interior and exterior applications Designed for easy fitting, clips directly over the glass: no welding required and can be installed after glass is fitted BH2 End Cap 22mm 30mm EUHB50 Handrail bracket 26mmØ hole in glass for EUHB50 Supplied 150mm high for on-site trimming EUHB50SQ Handrail bracket, square 26mmØ hole in glass Supplied 150mm high for on-site trimming EUHBTF50 Handrail bracket timber fix Designed for timber fixing Supplied 150mm high for on-site trimming EUHBTF50SQ Handrail bracket timber fix, square Designed for timber fixing Supplied 150mm high for on-site trimming B28

29 BRACKETS & clamps BCI/BCWM/BC90/BC135 Balustrade clamps Polished stainless Satin stainless Suitable for 12mm glass 316 grade stainless steel Supplied with rubber gasket inserts typical height BCI Glass-to-Glass BCWM Wall Mount BC90 90 Corner BB70/BB70SQ Balustrade brackets, wall mount Polished stainless Satin stainless Suitable for 10 and 12mm glass 316 grade stainless steel Round and square options 18 BB70 BB70SQ BBD70/BBD70SQ Balustrade brackets, glass/glass Polished stainless Satin stainless Suitable for 10 and 12mm glass 316 grade stainless steel Round and square options Ø18 hole in glass 45 BBD70 BBD70SQ B29

30 clamps BCRD6/10, BCFD6/10, BCRS8/10, BCFS8/10 Glass clamps, post or wall mount Polished stainless Satin stainless Options for 6, 8, 10 and 12mm glass 316 grade stainless steel Round and square profiles Flat back for fixing to square section and wall mounting, or round back to suit 50mm tubular post BCRD6 Round back 6-8mm glass BCFD6 Flat back 6-8mm glass 6-8mm Glass mm Glass mm Glass mm Glass BCRS8 Round back 8-10mm glass BCFS8 Flat back 8-10mm glass BCRD10 Round back 10-12mm glass BCFD10 Flat back 10-12mm glass mm Glass mm Glass BCRS10 Round back 10-12mm glass BCFS10 Flat back 10-12mm glass mm Glass mm Glass B30

31 vienna hydraulic hinges EH1NHO Glass to wall hydraulic hinge, marine grade Made from aluminium and stainless steel Hinge opening angle 100 Self-closing from any angle Available as non-hold open (for pool environments) and hold open (doors) Non-hold open has an offset closed position to hold the gate or door firmly shut, preventing rattle Maximum recommended glass weight: 70kg Maximum recommended door width: 900mm Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request Screw on each pivot block adjusts hydraulic closing speed EH1LNHO Glass to wall hydraulic hinge, offset, marine grade Made from aluminium and stainless steel Hinge opening angle 100 Self-closing from any angle Available as non-hold open (for pool environments) and hold open (doors) Non-hold open has an offset closed position to hold the gate or door firmly shut, preventing rattle Maximum recommended glass weight: 70kg Maximum recommended door width: 900mm Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request Screw on each pivot block adjusts hydraulic closing speed EH2NHO Glass to glass hydraulic hinge, marine grade 316 Glass cut-out detail 50 Made from aluminium and stainless steel Hinge opening angle 100 Self-closing from any angle Available as non-hold open (for pool environments) and hold open (doors) Non-hold open has an offset closed position to hold the gate or door firmly shut, preventing rattle Maximum recommended glass weight; 70kg Maximum recommended door width; 900mm Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request Screw on each pivot block adjusts hydraulic closing speed R 5 R 13 6 B31

32 vienna pool gate latches (Profile & finish to complement hydraulic hinge) EHPL1 Gate latch and strike 33, marine grade mm Designed for a frameless glass pool gate that closes to a post or wall Single action, self-latching magnetic operation Manufactured in aluminium and stainless steel Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request 100mm 66 ø16 Gate Panel 150 min Return/Post EHPL1RP Round Post Gate latch and strike, marine grade mm 8 Glass Preparation 33 Designed for a frameless glass pool gate 50mm dia. post mount Single action, self-latching magnetic operation Manufactured in aluminium and stainless steel Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request 100mm 66 ø16 Gate Panel 150 min Return/Post Made to order only 5 Glass Preparation EHPL2 Gate latch and keeper 33 33, marine grade mm Designed for a frameless glass pool gate and side panel Single action, self-latching magnetic operation Manufactured in aluminium and stainless steel Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request 100mm 66 ø16 Ø12 Gate Panel ø16 Ø min 5 Glass Preparation EHPL290 Gate latch and keeper 50mm, marine grade mm ø16 Designed for a frameless glass pool gate that closes to a side panel at 90 Single action, self-latching magnetic operation100mm Manufactured in aluminium and stainless steel Standard for 12mm glass, can be supplied for 10mm or 15mm glass on request Top View 66 Side View Glass Preparation 38mm B32

33 BALUSTRADE & pool: PIVOTS FPF790 Europool top pivot arm 90 91mm 106mm 167mm Designed for mounting a glass gate to a glass balustrade Used in conjunction with HPT20/HPT10 top patch fittings that allows them to work as a top pivot set Frameless glass mounting Manufactured in 316 stainless steel FPF790L left hand 91mm 30mm 167mm 106mm ASSSEMBLY (rh) 30mm FPF790R right hand RETURN PANEL DOOR HPT20PG Top fitting to suit pool gate pivots R Top patch fitting suitable for Euroglass pool gate fittings: FPF5/FPF6/FPF7 and FPF790/FPF8 Adjustable pivot insert Features concealing cover plates 52mm 31mm 166mm B33