Exporting Gerber and Drill Files from Altium Designer

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Exporting Gerber and Drill Files from Altium Designer"

Transcription

1 Exporting Gerber and Drill Files from Altium Designer This document describes the preferred method for generating Gerber and Drill files to print custom circuits on the Voltera V-One. Before proceeding, it is recommended to read the Circuit Design Rules. Each section is followed by a screenshot summarizing the recommended export configuration settings, however a detailed explanation of each step is also given. The screenshots are of Altium Designer 13.2 running on Windows 8.1. The exact names of the settings presented may differ based on the Altium Designer version, operating system, and circuit design in question. Exporting Gerber Files From the.pcbdoc file, navigate to File > Fabrication Outputs > Gerber Files. GENERAL TAB The General Tab presents Units and Format configuration. The Voltera V-One software prefers the Units to be in millimeters, however either inches or millimeters will work. The Format is related to the resolution with which the Gerber data is presented. For the Voltera V-One, the highest resolution option is always the best, and this should be the option lowest down in the list that Altium presents. Generally, 2:5 will suffice.

2 LAYERS TAB In this tab the user is presented with Layers to Plot and Mechanical Layer(s) to Add. The mechanical layers can be ignored, but Layers to Plot is extremely important. To print single layer circuits, plot the GTL (Top Layer) file. To print two layer circuits, plot GTL and GBL (Bottom Layer) files. For solder paste dispensing, also plot GTS (Top Solder). Important note: ensure that Mirror is unchecked for all files.

3 DRILL DRAWINGS TAB Not much work to be done here - ensure everything is unchecked. Ignore the legend symbols.

4 APERTURES The checkbox Embedded apertures (RS274X) should be checked, greying out all other options under this tab. ADVANCED All numbers under the Film size section can be left to whatever Altium generates. Film size is dependent on how spread apart components are, and Altium will raise an error if this area is too small. Under Aperture Matching Tolerances, both Plus and Minus should be set to 0.005mil. Under Batch mode, select Separate file per layer, ensuring Panelize layers is not selected. Under Leading/Trailing Zeroes, select Suppress leading zeros. The Voltera V-One software prefers this format as it makes print sequencing easier to handle (speeding up processing time), however other formats are supported, albeit less predictable. Under Position on Film, select Reference to relative origin.

5 Under Plotter Type, select Unsorted (raster). Under the Other settings section, ensure that G54 on aperture change is unchecked, Use software arcs is unchecked, Optimize change location commands is checked, and Generate DRC Rules export file (.RUL) is checked. The printer may or may not use the.rul file depending on how complex the print is. To complete the Gerber file exporting, click OK. Doing so will launch a program called CAMtastic. CAMtastic also has a Gerber exporting tool, however, these Gerber files don t contain the same amount of information as the ones just exported. CAMtastic is great to proof the circuit design, but no work needs to be done once in CAMtastic. Retrieving the exported Gerber files is outlined at the bottom of this document.

6 Exporting NC Drill Files After going back to the.pcbdoc file (NOT CAMtastic), navigate to File > Fabrication Outputs > NC Drill Files. The Drill file is important to export for two reasons. 1) Ink will be saved as it is not dispensed on areas that have been (or will be) drilled through, and 2) the ink is susceptible to cracking if drilled through directly. As before, Units can be set to either Inches or Millimeters. Also as before, the Format should be set to the highest precision possible. The lowest on the list of available options tends to be the highest precision; generally 2:5 will suffice. Under Leading/Trailing Zeroes, select Suppress leading zeros. Under Coordinate Positions, select Reference to relative origin. Under the Other settings, ensure that Optimize change location commands is checked, Generate separate NC Drill files for plated & non-plated holes is checked, Use drilled slot command (G85) is unchecked, Generate Board Edge Rout Paths is unchecked, and Generate EIA Binary Drill File (.DRL) is Even if CAMtastic is launched, it s only purpose is viewing the project outputs. There is an option to File > Export > Drill menu in CAMtastic, however the drill file that CAMtastic will export will not have as much information as the drill file just exported.

7 Retrieving Exported Files All the exported files live in the same folder. To find this folder, look at the top of the Altium Designer window when viewing the.pcbdoc file in which board layouts are designed. It should display the exact file path to the.pcbdoc file being viewed. Find the directory in which this.pcbdoc file exists, and look for the folder Project Outputs for <Your_Project_Name>.

Gerber Setup. Summary. Access. Options/Controls. General Tab. Modified by Rob Evans on 23-Aug Parent page: WorkspaceManager Dialogs

Gerber Setup. Summary. Access. Options/Controls. General Tab. Modified by Rob Evans on 23-Aug Parent page: WorkspaceManager Dialogs Gerber Setup Modified by Rob Evans on 23-Aug-2016 Parent page: WorkspaceManager Dialogs Summary Each Gerber file corresponds to one layer in the physical board the component overlay, top signal layer,

More information

OurPCB Gerber Generation - Altium

OurPCB Gerber Generation - Altium OurPCB Gerber Generation - Altium Summary Each Gerber file corresponds to one layer in the physical board the component overlay, top signal layer, bottom signal layer, the solder masking layers and so

More information

How to export Gerber files from Altium Designer (Protel) matching Olimex PCB production

How to export Gerber files from Altium Designer (Protel) matching Olimex PCB production How to export Gerber files from Altium Designer (Protel) matching Olimex PCB production Design Setup from Altium Contents 1. Clearance Setup... 3 2. Routing Width... 4 3. Plane Connect... 4 4. Plane Clearance...

More information

Best Practices in PCB Design: Exporting Gerber Files

Best Practices in PCB Design: Exporting Gerber Files Page 1 of 5 Improve your ni.com experience. Login or Create Document Type: Tutorial NI Supported: Yes Publish Date: Mar 4, 2009 Best Practices in PCB Design: Exporting Gerber Files Overview This document

More information

CAM Editor Imports and Exports

CAM Editor Imports and Exports CAM Editor Imports and Exports Modified by on 6-Aug-2014 This tutorial looks at importing and exporting a variety of CAM files using Altium Designer's CAM Editor (also referred to as CAMtastic ). During

More information

Complete. PCB Design Using. NI Multisim, NI Ultiboard, LPKF CircuitCAM and BoardMaster. pg. 1. Wei Siang Pee

Complete. PCB Design Using. NI Multisim, NI Ultiboard, LPKF CircuitCAM and BoardMaster. pg. 1. Wei Siang Pee Complete Wei Siang Pee PCB Design Using NI Multisim, NI Ultiboard, LPKF CircuitCAM and BoardMaster pg. 1 Introduction Multisim equips educators, students, and professionals with the tools to analyze circuit

More information

PCB Design Tools. Orcad (Cadence) Allegro (Cadence) Eagle (Cadsoft) P-CAD (Altium)

PCB Design Tools. Orcad (Cadence) Allegro (Cadence) Eagle (Cadsoft) P-CAD (Altium) What Is PCB? A PCB is a printed circuit board, also known as a printed wiring board. It is used in electronics to build electronic devices. A PCB serves two purposes in the construction of an electronic

More information

Detailed information about Gerber, NC Drill and NC Route.

Detailed information about Gerber, NC Drill and NC Route. Title: Product: Summary: Manufacturing Output OrCAD / Allegro PCB Editor Detailed information about Gerber, NC Drill and NC Route. Author/Date: Beate Wilke / 27.05.2009 Table of Contents 1 Gerber... 2

More information

University of Kansas EECS Circuit Board Fabrication Tutorial for 212 Lab

University of Kansas EECS Circuit Board Fabrication Tutorial for 212 Lab University of Kansas EECS Circuit Board Fabrication Tutorial for 212 Lab Preparing For Export... 1 Assigning Footprints... 1 Recommended Footprints... 2 No Connects... 3 Design Rules Check... 3 Create

More information

Prototyping Printed Circuit Boards

Prototyping Printed Circuit Boards Prototyping Printed Circuit Boards From concept to prototype to production. (HBRC) PCB Design and Fabrication Agenda Introduction Why PCBs? Stage 1 Understanding the rules Stage 2 Planning the board. Stage

More information

Release Highlights for CAM350 Product Version 10.2

Release Highlights for CAM350 Product Version 10.2 Release Highlights for CAM350 Product Version 10.2 Introduction CAM350 Version 10.2.2 is a support release for CAM350. CAM350 10.2.2 includes support for Microsoft Windows 7 and Mentor PADS Layout version

More information

PCB Prototyping Machine. Auto Lab. Tutorial MITS Electronics

PCB Prototyping Machine. Auto Lab. Tutorial MITS Electronics PCB Prototyping Machine Auto Lab Tutorial MITS Electronics REVISION: October 1, 2011 1st edition CONTENTS: Design Pro Applications Import Gerber Files Import Drill File Auto Drill Generate Outline Generate

More information

PCB Artist Tutorial:

PCB Artist Tutorial: Derek Brower browerde@msu.edu Capstone Design Team 6 PCB Artist Tutorial: Printed Circuit Board Design Basics N o v e m b e r 1 4, 2 0 1 2 P C B B a s i c s P a g e 1 Abstract PCB Artist is a schematic

More information

EEL 3923C. JD/ Module 6 PCB Design Using Altium Suite. Jason Reeder and Michael Stapleton Fall 2011

EEL 3923C. JD/ Module 6 PCB Design Using Altium Suite. Jason Reeder and Michael Stapleton Fall 2011 EEL 3923C JD/ Module 6 PCB Design Using Altium Suite Jason Reeder and Michael Stapleton Fall 2011 I. Assignment (PCB Design) A. Design PCB using Altium Suite 1. Obtain your specific circuit to design the

More information

Additional we have some CAD Tools in use to work with the data directly from your systems. Type Name from. CAD Eagle

Additional we have some CAD Tools in use to work with the data directly from your systems. Type Name from. CAD Eagle Formats With our CAM Systems we are able to handle all current formats. Additional we have some CAD Tools in use to work with the data directly from your systems. In detail these are Type Name from CAD

More information

Executive Summary. Table of Contents

Executive Summary. Table of Contents Executive Summary How to Create a Printed Circuit Board (PCB) Department of Electrical & Computer Engineering Michigan State University Prepared by: John Kelley Revision: 4/06/00 This application note

More information

A-PDF AutoCAD to PDF utility. User Documentation

A-PDF AutoCAD to PDF utility. User Documentation Note: This product is distributed on a try-before-you-buy basis. All features described in this documentation are enabled. The registered version does not insert a watermark in your generated pdf documents.

More information

Chapter 4 Dimensioning Drawings

Chapter 4 Dimensioning Drawings Chapter 4 Dimensioning Drawings In this chapter, we are going to learn how to dimension the drawings we are creating. AutoCAD supplies many different tools for creating these dimensions quickly and easily.

More information

Configuring a Macintosh Laptop to Use Multiple Displays

Configuring a Macintosh Laptop to Use Multiple Displays Configuring a Macintosh Laptop to Use Multiple Displays These instructions may be useful if you are connecting a Mac laptop to a secondary monitor or to a projector within the Ideal Learning Environment

More information

Your PCB layout First time right

Your PCB layout First time right Your PCB layout First time right Smart menus & PCB visualizer DRC/DFM free online tools s Hertogenbosch 29 October 2014 Slide 1 PCB visualisation - Goals Help busy designers get boards on time accurate

More information

[INTRODUCTION TO PCB ARTIST]

[INTRODUCTION TO PCB ARTIST] 2013 ECE 480 Design Team 3 Justin Bohr [INTRODUCTION TO PCB ARTIST] This document will provide a guide of how to create relatively simple printed circuit board (PCB) with the PCB Artist tool. An overview

More information

Printed Circuit Boards: Layout Design

Printed Circuit Boards: Layout Design Printed Circuit Boards: Layout Design Review: Process Summary Manufacturing Constraints Gerber Schematic Board Manufacture Excellon Drill This is art! Ensure that the schematic is accurate. Run the ERC

More information

Email Address Collector. - Tutorial -

Email Address Collector. - Tutorial - Email Address Collector - Tutorial - How to extract email addresses from mail folders 1. Open Email Address Collector Once the product is installed and your license is activated, you can start extracting

More information

User Support Resource

User Support Resource User Support Resource Clearing Browser Cache To optimize your experience in the MyUNLV system, it may be necessary to clear your browser cache. While it is not necessary to clear you cache every time you

More information

EZ-Route2000 Instructions

EZ-Route2000 Instructions EZ-Route2000 Instructions Ver24 Completely rewritten for: Windows95/98/2000/ME/NT/XP EZ-Route2000 was created in Florida by: Phillip L. Bolin Copyright (C) 1999-2005 Previous versions: PC-PRO PC-Pro II

More information

PCB VERIFICATION AND ORDERING. George Hadley 2016, Images Property of their Respective Owners.

PCB VERIFICATION AND ORDERING. George Hadley 2016, Images Property of their Respective Owners. PCB VERIFICATION AND ORDERING George Hadley 2016, Images Property of their Respective Owners. OUTLINE PCB Verification Parts Completion Check Footprint Verification Check Parts Placement Check Space Conflicts

More information

PCB Design with Altium: PCB Layout and Ordering a Board

PCB Design with Altium: PCB Layout and Ordering a Board PCB Design with Altium: PCB Layout and Ordering a Board Alex Fosdick Capstone Senior Design Instructor: Tom Brown Edited: February 3rd, 2011 Description: This document is the second of two in describing

More information

DWGSee Professional User Guide

DWGSee Professional User Guide DWGSee Professional User Guide DWGSee is comprehensive software for viewing, printing, marking and sharing DWG files. It is fast, powerful and easy-to-use for every expert and beginners. Starting DWGSee

More information

In this lab you will explore the Windows XP Firewall and configure some advanced settings.

In this lab you will explore the Windows XP Firewall and configure some advanced settings. 16.3.2 Lab: Configure Windows XP Firewall Print and complete this lab. In this lab you will explore the Windows XP Firewall and configure some advanced settings. Recommended Equipment Two computers directly

More information

educ Office 365 email: Remove & create new Outlook profile

educ Office 365 email: Remove & create new Outlook profile Published: 29/01/2015 If you have previously used Outlook the with the SCC/SWO service then once you have been moved into Office 365 your Outlook will need to contact the SCC/SWO servers one last time

More information

MERGING (MERGE / MOSAIC) GEOSPATIAL DATA

MERGING (MERGE / MOSAIC) GEOSPATIAL DATA This help guide describes how to merge two or more feature classes (vector) or rasters into one single feature class or raster dataset. The Merge Tool The Merge Tool combines input features from input

More information

Preparing a File For Commercial Printing using Microsoft Publisher

Preparing a File For Commercial Printing using Microsoft Publisher Preparing a File For Commercial Printing using Microsoft Publisher Microsoft Publisher was built for casual home use and is setup to print on a home inkjet printer using the default Windows RGB print drivers.

More information

10.3.1.10 Lab - Configure a Windows XP Firewall

10.3.1.10 Lab - Configure a Windows XP Firewall 5.0 10.3.1.10 Lab - Configure a Windows XP Firewall Print and complete this lab. In this lab, you will explore the Windows XP Firewall and configure some advanced settings. Recommended Equipment Step 1

More information

PCB Printout Output Options. Contents

PCB Printout Output Options. Contents PCB Printout Output Options Contents Configuring 2D Print-based Output Adding a New Printout Configuring a Printout Adding a New Layer Configuring a Layer Setting Print Preferences Colors and Grayscales

More information

PCB Fabrication Services and Preparation

PCB Fabrication Services and Preparation PCB Fabrication Services and Preparation RSGC ACES PCB Fabrication Service Providers Bittele Electronics Inc. Preparing Eagle Files For Production What is a Gerber RS-274X File? Short Wikipedia Spiel Creating

More information

PDF Word to PDF utility. User Documentation

PDF Word to PDF utility. User Documentation Note: This product is distributed on a try-before-you-buy basis. All features described in this documentation are enabled. The registered version does not insert a watermark in your generated pdf documents.

More information

Laboratory 4, PCB Project Merging with Gerbtool

Laboratory 4, PCB Project Merging with Gerbtool Cmpe174 Lab-4, Rev-4.0.0 page 1 University of California, Santa Cruz Computer Engineering Department Laboratory 4, PCB Project Merging with Gerbtool CMPE174, Intro to EDA Tools S.C. Petersen 1. INTRODUCTION

More information

Universal Simple Control, USC-1

Universal Simple Control, USC-1 Universal Simple Control, USC-1 Data and Event Logging with the USB Flash Drive DATA-PAK The USC-1 universal simple voltage regulator control uses a flash drive to store data. Then a propriety Data and

More information

Education Solutions Development, Inc. APECS Navigation: Business Systems Getting Started Reference Guide

Education Solutions Development, Inc. APECS Navigation: Business Systems Getting Started Reference Guide Education Solutions Development, Inc. APECS Navigation: Business Systems Getting Started Reference Guide March 2013 Education Solutions Development, Inc. What s Inside The information in this reference

More information

InDesign CS4-5.5 Part II

InDesign CS4-5.5 Part II InDesign CS4-5.5 Part II Library A library is a file and holds a collection of commonly used objects. A library is a file (extension.indl) and it is stored on disk. A library file can be open at any time

More information

Tutorial 9: Creating Layout Plans and Printing

Tutorial 9: Creating Layout Plans and Printing Tutorial 9: Creating Layout Plans and Printing Tutorial Content 9.1. What is the layout view and how is this different to the data view? 9.2. How do I set out a map for printing in ArcMap? 9.3. What tools

More information

www.eurocircuits.com Page 1

www.eurocircuits.com Page 1 CONTENT INTRODUCTION 2 INPUT DATA FORMATS 3 INPUT DATA REQUIREMENTS 4 CLASSIFICATION 6 HOLES 8 COPPER LAYERS 10 BGAS 12 MECHANICAL LAYER 13 SOLDERMASK 15 LEGEND PRINT 17 CARBON 18 PEEL-OFF MASK 19 VIAFILL

More information

AltiumWorkshop. Basic Altium Workshop HKN Friday, September 23th, 2009 Prepared by HKN CU Boulder Chapter

AltiumWorkshop. Basic Altium Workshop HKN Friday, September 23th, 2009 Prepared by HKN CU Boulder Chapter Basic Altium Workshop Friday, September 23th, 2009 Prepared by HKN CU Boulder Chapter Why do a PCB? PCBs are pretty cheap $33 for 2-layer boards from www.4pcb.com Compact and Robust Signal speed and reduced

More information

Layouts, Plotting, Printing

Layouts, Plotting, Printing Layouts, Plotting, Printing Sacramento City College Engineering Design Technology Layouts, Plotting, Printing 1 Objectives Print and plot a drawing. Set up layouts using title blocks and viewports. Create

More information

EXPORTING GERBER FILES FROM EAGLE

EXPORTING GERBER FILES FROM EAGLE EXPORTING GERBER FILES FROM EAGLE V1.1 09/2014 DESIGN RULES CHECK 1 GENERATING DRILL RACK FILE 2 GENERATING EXCELLON DRILL FILES 3 GENERATING GERBER FILES 4 SENDING GERBER FILES 11 KNOWN EAGLE FILE EXTENSIONS

More information

Virtual Office Remote Installation Guide

Virtual Office Remote Installation Guide Virtual Office Remote Installation Guide Table of Contents VIRTUAL OFFICE REMOTE INSTALLATION GUIDE... 3 UNIVERSAL PRINTER CONFIGURATION INSTRUCTIONS... 12 CHANGING DEFAULT PRINTERS ON LOCAL SYSTEM...

More information

So you say you want something printed...

So you say you want something printed... So you say you want something printed... Well, that s great! You ve come to the right place. Whether you re having us design and edit your work, or you fancy yourself a designer and plan to hand over your

More information

Designing a Schematic and Layout in PCB Artist

Designing a Schematic and Layout in PCB Artist Designing a Schematic and Layout in PCB Artist Application Note Max Cooper March 28 th, 2014 ECE 480 Abstract PCB Artist is a free software package that allows users to design and layout a printed circuit

More information

R. Reports Menu: 3. Trial Balance

R. Reports Menu: 3. Trial Balance R. Reports Menu: 3. Trial Balance Table of Contents Trial Balance... 3 The General tab... 3 The Accounts tab... 5 The Export Options tab... 6 The Period tab... 7 Click on R. Reports Menu from the Main

More information

USING STUFFIT DELUXE THE STUFFIT START PAGE CREATING ARCHIVES (COMPRESSED FILES)

USING STUFFIT DELUXE THE STUFFIT START PAGE CREATING ARCHIVES (COMPRESSED FILES) USING STUFFIT DELUXE StuffIt Deluxe provides many ways for you to create zipped file or archives. The benefit of using the New Archive Wizard is that it provides a way to access some of the more powerful

More information

File Folders. To produce a file folder you have the following options:

File Folders. To produce a file folder you have the following options: File Folders To produce a file folder you have the following options: Option 1: Supply us with the file for the full outside of the file folder and another file for the full inside of the file folder (see

More information

ecw Weekly Users Tip: My Settings: Template-Friendly Settings & My Favorites: Templates

ecw Weekly Users Tip: My Settings: Template-Friendly Settings & My Favorites: Templates ecw Weekly Users Tip: My Settings: Template-Friendly Settings & My Favorites: Templates Templates, regardless of how basic or how comprehensive, can make your notes overwhelming and visually harder to

More information

Downloading Driver Files

Downloading Driver Files The following instructions are for all DPAS supported Intermec printers. The Intermec InterDriver EasyCoder PD42 (203 dpi) - IPL driver has been tested and recommended for DPAS use. This driver will support

More information

Backing up IMail Server using Altaro Backup FS

Backing up IMail Server using Altaro Backup FS Backing up IMail Server using Altaro Backup FS Purpose The purpose of this document is to provide guidelines and procedures for backing up IMail server system data and user data in case of a hardware or

More information

for Sage 100 ERP Business Insights Overview Document

for Sage 100 ERP Business Insights Overview Document for Sage 100 ERP Business Insights Document 2012 Sage Software, Inc. All rights reserved. Sage Software, Sage Software logos, and the Sage Software product and service names mentioned herein are registered

More information

Tutorials Creating your own components

Tutorials Creating your own components Step 1 of 5: Introduction This tutorial shows you how to create your own circuit symbol and PCB component by customizing the PCB Wizard library. You should have experience of PCB Wizard's drawing and editing

More information

BOOKING CONFERENCES IN TMS

BOOKING CONFERENCES IN TMS BOOKING CONFERENCES IN TMS Introduction The purpose of this document is to guide a person through the process of scheduling a video conference using TMS. Endpoints The endpoint listings in TMS are connections

More information

AutoDWG DWGSee DWG Viewer. DWGSee User Guide

AutoDWG DWGSee DWG Viewer. DWGSee User Guide DWGSee User Guide DWGSee is comprehensive software for viewing, printing, marking and sharing DWG files. It is fast, powerful and easy-to-use for every expert and beginners. Starting DWGSee After you install

More information

INTRODUCTION to ESRI ARCGIS For Visualization, CPSC 178

INTRODUCTION to ESRI ARCGIS For Visualization, CPSC 178 INTRODUCTION to ESRI ARCGIS For Visualization, CPSC 178 1) Navigate to the C:/temp folder 2) Make a directory using your initials. 3) Use your web browser to navigate to www.library.yale.edu/mapcoll/ and

More information

How to Configure Microsoft System Operation Manager to Monitor Active Directory, Group Policy and Exchange Changes Using NetWrix Active Directory

How to Configure Microsoft System Operation Manager to Monitor Active Directory, Group Policy and Exchange Changes Using NetWrix Active Directory How to Configure Microsoft System Operation Manager to Monitor Active Directory, Group Policy and Exchange Changes Using NetWrix Active Directory Change Reporter Table of Contents General Information...

More information

Adobe Acrobat 6.0 Professional

Adobe Acrobat 6.0 Professional Adobe Acrobat 6.0 Professional Manual Adobe Acrobat 6.0 Professional Manual Purpose The will teach you to create, edit, save, and print PDF files. You will also learn some of Adobe s collaborative functions,

More information

Contents Accounting Software Imports - Summary

Contents Accounting Software Imports - Summary Contents Importing the Trial Balance... 1 Accounting Software Imports - Summary... 1 Pastel Partner/Express... 1 Direct Import... 1 Indirect Import... 3 QuickBooks... 7 Indirect Import... 7 Installation

More information

InfoView User s Guide. BusinessObjects Enterprise XI Release 2

InfoView User s Guide. BusinessObjects Enterprise XI Release 2 BusinessObjects Enterprise XI Release 2 InfoView User s Guide BusinessObjects Enterprise XI Release 2 Patents Trademarks Copyright Third-party contributors Business Objects owns the following U.S. patents,

More information

Connecting to Staffmail with Outlook 2011 on Mac OS X

Connecting to Staffmail with Outlook 2011 on Mac OS X EXSEED Client Integration Testing Version 1.0 Connecting to Staffmail with Outlook 2011 on Mac OS X This document will help you connect Outlook 2011 for Mac OS X on a computer that is not on Edinburgh

More information

Managing Multiple Displays. Section 1 Open Display settings. Windows 7 and 8.1 vs Windows 10. Overview

Managing Multiple Displays. Section 1 Open Display settings. Windows 7 and 8.1 vs Windows 10. Overview Managing Multiple Displays If you are using two or more displays on your computer, you need to set up the displays in proper order so your setup feels natural to use. Once you have done this once or twice,

More information

Mailbox Reduction and Archiving Guide Outlook for MAC

Mailbox Reduction and Archiving Guide Outlook for MAC Mailbox Reduction and Archiving Guide Outlook for MAC To support the migration of SuccessFactors corporate email data to the SAP system, SuccessFactors are aligning their email quota policy with that of

More information

Troubleshooting Guide. 2.2 Click the Tools menu on Windows Explorer 2.3 Click Folder Options. This will open a dialog box:

Troubleshooting Guide. 2.2 Click the Tools menu on Windows Explorer 2.3 Click Folder Options. This will open a dialog box: Listed below are errors you could possibly encounter when trying to log into Business Online after upgrading to the latest version of Java. Click on the link for a full explanation of the error and the

More information

Setting up a site directly to the H-drive in Dreamweaver CS4

Setting up a site directly to the H-drive in Dreamweaver CS4 Department of Technology Assistance Overview: This document will describe how to setup a personal website via the H-drive at RU using Dreamweaver

More information

Printing Guide. MapInfo Pro Version 15.0. Contents:

Printing Guide. MapInfo Pro Version 15.0. Contents: MapInfo Pro Version 15.0 The purpose of this guide is to assist you in getting the best possible output from your MapInfo Pro software. We begin by covering the new print, import, and export features and

More information

2 Power Jet Plotting Program

2 Power Jet Plotting Program 2 Power Jet Plotting Program 2.1 POWER JET PLOTTER ENVIRONMENT SETTINGS CONFIGURATION A) The Queue File window should NEVER be changed (C:\Power\coda.cod). B) The Manual Management box: - If the plotter

More information

4.3 Plotting GPS Coordinates

4.3 Plotting GPS Coordinates Plotting Locations Plotting GPS Coordinates 4.3.1 4.3 Plotting GPS Coordinates For many projects you will want to plot coordinates. First you must set the projection of your map. Setting the projection

More information

How to Record a Collaborate Session

How to Record a Collaborate Session STaR Quick Start Guide How to Record a Collaborate Session Collaborate sessions can be recorded and provided to students for playback. Collaborate can also be used to record lectures and linked next to

More information

Guide to Designing and Fabricating Printed Circuit Boards

Guide to Designing and Fabricating Printed Circuit Boards Guide to Designing and Fabricating Printed Circuit Boards Rev 1.0 University of Toronto January 2006 Contact for ECE496 students: Olivier Trescases trescas@vrg.utoronto.ca Outline Outline...2 Glossary...3

More information

GC-Prevue Instructions

GC-Prevue Instructions GC-Prevue Instructions Welcome to GC-Prevue. These instructions include two sections: THE GC-PREVUE INTERFACE and LOADING DATA. They are written for Version 9 and are designed to be used in conjunction

More information

Downloading Driver Files

Downloading Driver Files The following instructions are for all DPAS supported Zebra printers except the Zebra GK420t. The ZDesigner R110Xi4 203 dpi driver has been tested and recommended for DPAS use. This driver will support

More information

Plotting a Drawing to a good JPEG:

Plotting a Drawing to a good JPEG: Plotting a Drawing to a good JPEG: First open your drawing and set it to the layout or model space view you wish to plot. Be sure that your layer settings are set they way you want them. First start the

More information

Laser Cutter for AutoCAD

Laser Cutter for AutoCAD Laser Cutter for AutoCAD General Information: This guide is to serve for setup of the file for laser cutting and does not serve to provide insight on how to use or operate AutoCAD. Any questions on how

More information

Security Guidelines for MapInfo Discovery 1.1

Security Guidelines for MapInfo Discovery 1.1 Security Guidelines for MapInfo Discovery 1.1 This paper provides guidelines and detailed instructions for improving the security of your Mapinfo Discovery deployment. In this document: Overview.........................................

More information

MapInfo Professional Version 12.5. Printing Guide

MapInfo Professional Version 12.5. Printing Guide MapInfo Professional Version 12.5 Printing Guide The purpose of this guide is to assist you in getting the best possible output from your MapInfo Professional software. We begin by covering the new print,

More information

EZCT. VERSION 5.x SOFTWARE MANUAL. EZCT and EZCT-10

EZCT. VERSION 5.x SOFTWARE MANUAL. EZCT and EZCT-10 EZCT VERSION 5.x SOFTWARE MANUAL For Use with Vanguard s EZCT and EZCT-10 Current Transformer Testers Vanguard Instruments Company, Inc. 1520 S. Hellman Ave. Ontario, California 91761, USA TEL: (909) 923-9390

More information

ACE: Illustrator CC Exam Guide

ACE: Illustrator CC Exam Guide Adobe Training Services Exam Guide ACE: Illustrator CC Exam Guide Adobe Training Services provides this exam guide to help prepare partners, customers, and consultants who are actively seeking accreditation

More information

Viewing and Troubleshooting Perfmon Logs

Viewing and Troubleshooting Perfmon Logs CHAPTER 7 To view perfmon logs, you can download the logs or view them locally. This chapter contains information on the following topics: Viewing Perfmon Log Files, page 7-1 Working with Troubleshooting

More information

DMU Viewer CATIA V5R19 TABLE OF CONTENTS

DMU Viewer CATIA V5R19 TABLE OF CONTENTS TABLE OF CONTENTS Introduction...1 DMU Viewer...1 Product Structure Introduction...3 Pull Down Menus...4 Start...4 File...5 Edit...6 View...9 Insert...12 Tools...13 Analyze...16 Window...17 Help...18 Product

More information

Printer setup and first steps

Printer setup and first steps Printer setup and first steps Contents: PrintJet II:... 2 Install printer driver... 2 Calibrating the PrintJet II... 3 Setting marker types... 6 Calibrating the marker type:... 7 PrintJet PRO:... 11 Install

More information

Sales Catalogue. The Sales Catalogue Menu Item. 1. Click on Utilities. 2. Choose Export. 3. Click on Sales Catalogue

Sales Catalogue. The Sales Catalogue Menu Item. 1. Click on Utilities. 2. Choose Export. 3. Click on Sales Catalogue Sales Catalogue The Sales Catalogue Menu Item 1. Click on Utilities 2. Choose Export 3. Click on Sales Catalogue The Sales Catalogue Extract Window Use this window to specify the Template name or Add a

More information

Importing Data from ECAD Systems. Mentor PADS Layout 2005 ASCII EXPORT

Importing Data from ECAD Systems. Mentor PADS Layout 2005 ASCII EXPORT Importing Data from ECAD Systems...1 Mentor PADS Layout 2005 ASCII EXPORT...1 Mentor Expedition 2005 ODB++ EXPORT...3 Cadence Allegro ODB++ EXPORT...5 Trademarks...7 Importing Data from ECAD Systems This

More information

Calculator Notes for the TI-Nspire and TI-Nspire CAS

Calculator Notes for the TI-Nspire and TI-Nspire CAS INTRODUCTION Calculator Notes for the Getting Started: Navigating Screens and Menus Your handheld is like a small computer. You will always work in a document with one or more problems and one or more

More information

CREATING AN IMAGE FROM AUTOCAD CADD NOTE 16. MENU: AutoCAD, File, Plot COMMAND: plot ICON:

CREATING AN IMAGE FROM AUTOCAD CADD NOTE 16. MENU: AutoCAD, File, Plot COMMAND: plot ICON: CADD NOTE 16 This CADD Note provides instructions on creating an image from an AutoCAD drawing that can be pasted into another application (e.g., Word, Powerpoint, etc.). These instructions assume the

More information

Creating Home Directories for Windows and Macintosh Computers

Creating Home Directories for Windows and Macintosh Computers ExtremeZ-IP Active Directory Integrated Home Directories Configuration! 1 Active Directory Integrated Home Directories Overview This document explains how to configure home directories in Active Directory

More information

Asset Track Getting Started Guide. An Introduction to Asset Track

Asset Track Getting Started Guide. An Introduction to Asset Track Asset Track Getting Started Guide An Introduction to Asset Track Contents Introducing Asset Track... 3 Overview... 3 A Quick Start... 6 Quick Start Option 1... 6 Getting to Configuration... 7 Changing

More information

Capturing Material. Section 3

Capturing Material. Section 3 Section 3 Capturing Material Duration: 60 minutes Capturing material is the process of creating media files from video or audio source material. This section describes how to capture material from different

More information

Model 288B Charge Plate Graphing Software Operators Guide

Model 288B Charge Plate Graphing Software Operators Guide Monroe Electronics, Inc. Model 288B Charge Plate Graphing Software Operators Guide P/N 0340175 288BGraph (80207) Software V2.01 100 Housel Ave PO Box 535 Lyndonville NY 14098 1-800-821-6001 585-765-2254

More information

Printing to Windows Shares from xprintserver using IPP/HTTP

Printing to Windows Shares from xprintserver using IPP/HTTP Scenario: User has a printer connected directly to a Windows Server 2003 or 2008 server and wants to print to it from an ios device using the xprintserver. Solution: Use Internet Printing support in Windows

More information

CNC Milling/ Routing Training

CNC Milling/ Routing Training CNC Milling/ Routing Training www.denford.co.uk Page C1 Table of contents Introduction... 3 Start the VR Milling V5 Software... 3 Configure the software for the machine... 4 Load your CNC file... 5 Configure

More information

Enhanced Imaging Options for Client Profiles for Windows

Enhanced Imaging Options for Client Profiles for Windows C ase Manag e m e n t by C l i e n t P rofiles Enhanced Imaging Options for Client Profiles for Windows T E C H N O L O G Y F O R T H E B U S I N E S S O F L A W Table of Contents 2 Table of Contents Scanning

More information

Native Banner / Java Fix

Native Banner / Java Fix Native Banner / Java Fix This help aid provides detailed instructions for removing new Java updates and installing the correct version of Java (Java version 7.40) for proper Native Banner operation. This

More information

enicq 5 External Data Interface User s Guide

enicq 5 External Data Interface User s Guide Vermont Oxford Network enicq 5 Documentation enicq 5 External Data Interface User s Guide Release 1.0 Published December 2014 2014 Vermont Oxford Network. All Rights Reserved. enicq 5 External Data Interface

More information

Mitigation Planning Portal MPP Reporting System

Mitigation Planning Portal MPP Reporting System Mitigation Planning Portal MPP Reporting System Updated: 7/13/2015 Introduction Access the MPP Reporting System by clicking on the Reports tab and clicking the Launch button. Within the system, you can

More information

Printing a Requisition Report

Printing a Requisition Report Printing a Requisition Report PURPOSE Use this procedure to print a requisition report. T RIGGER Perform this procedure after you have checked the Print box in the Approve Document screen in the Requisition.

More information

OrgPublisher Publishing

OrgPublisher Publishing OrgPublisher Publishing Version: 1.0 April 20, 2011 OrgPublisher 10 Training Copyright 2002 2011 All Rights Reserved by Aquire OrgPublisher, OrgPublisher Premier, Unifi, Mobile OrgPublisher, and Pocket

More information