Miniature electropilots U1

Transcription

1 Miniature electropilots Direct intervention electropilots with poppet valve system and cushioned bottom ssembly on subbase Threaded connections on the body CNOMO interface Orientable coil (3 ) separated from mechanical part Versions: 2/2 NO Original Univer SPEED modular subbases TECHNICL CHRCTERISTICS mbient temperature Fluid temperature Fluid Coutation system Ways/Positions Pressure Control Return Connections Nominal Ø () Nominal low rate (Nl/min) C max +95 C 0 μm iltered air, lubricated or not, neutral gases (upon request other luids can be used) direct intervention poppet valve system with cushioned,, (a) 2/2, = 0 0 = 3 0 electric mechanical spring on subbase or with threaded connections on the body subbase G /8 M5 CNOMO,2, CONSTRUCTIVE CHRCTERISTICS Materials ELECTRIC CHRCTERISTICS see features below Electropilots Series Coil Power consumption Connector Voltage Protection degree U3 D DC 3,5 W (DC) 5 V (C) 2,5 W (DC) 3,3 V (C) M 50 M 5 V DC 24 V DC 24 V C 0 V C 230 V C IP65 For other electric features see section ccessories>coils (a) = Mechanical part designed to keep the air supply always from the body (Useful in case of assembly of more NCNO pilots in series to have a unique supply port) _9

2 Miniature electropilots Sleeves with moving core Exhaust Ø,2 Pressure bar Weight Kg 0,030 0,030 0,030 cores and spring Upon request viton and s (only NC versions) NC NO Detail of machining Wrench 4 Locking rings for coils on s Version Suitable for s Material Coil 2 3 = radial exhausts 2 = radial exhausts 3 = open exhausts brass M523 M52 M52B In order to convey exhausts, use version 3 Standard manual s Functionig = with 2 position screw 2 = with impulse position screw 3 = with button with tool 4 = with button, position Suitable for s all NC electropilots that can use manual only CNOMO NC electropilots only CNOMO NC electropilots electropilots / M520(a) (a) = Mounted on the = with 2 position screw = with button with tool _0

3 Miniature electropilots 2/2 3/2 Electropilot for assembling on subbase 0, En. Deen , , Use SPEED subbase to build Manifolds, see following pages. vailable upon request: brass (without manual ), zamak,, other inner diameters /2 3/2 G/8 Electropilot brass 0, En. Deen , Electropilot to be used done. Brass body suitable for use with nonaggressive luiquids. No manual. vailable upon request: other inner diameters. 2/2 3/2 M5 Electropilot Electropilots brass 0, En. Deen , Electropilot to be used done. Brass body suitable for use with nonaggressive luiquids. No manual. vailable upon request: other inner diameters. = close the exhaust of the electropilot to get the 2/2 NO one (d) = the Ø shown on the 3/2 valves refers to the exhhaust Electropiltots are supplied without coil, connector and locking ring 0233 = manual on M520 ring nut = with 2 position screw _

4 Miniature electropilots CNOMO 2/2 3/2 Electropilot for mounting on subbases SPEED U2 0, En. Deen U, , Subbase: SPEED U2. vailable upon request: brass (without manual ). Zamak. Stainless steel other inner diameters. B B ISO 4762 Modular subbase SPEED series /U2 G/8 Electropilot for base U2 for base Connections G /8 G /8 Material zamak zamak Weight Kg 0,037 0,075 dvantages The original UNIVER Speed series was designed to solve some operational problems Possibility of deining the number of subbases at the moment of use Possibility of freely increasing or reducing the number of elements Quick assembly with special screw (builtin) standard supplied Reduction of stock holding Easy technical intervention ir supply is rotated by 90 in comparison with side consumption Standard (builtin) screw and ORing 0450 B0900 When assembling the manifold, put the bases on a lat surface and tighten the screw until the manifold is perfecty aligned. U2 ISO 4762 = close the exhaust of the electropilot to get the 2/2 NO one (d) = the Ø shown on the 3/2 valves refers to the exhhaust Electropiltots are supplied without coil, connector and locking ring = manual on ring nut M520 = with 2 position screw = with button with tool _

5 Miniature electropilots G/8 subbase N = Number of valve positions U2 G/8 CNOMO subbase 2 = Use N = Number of valve positions Electropilots _3

6 _4