1.5KE Series. Transient Voltage Suppression Diodes. Axial Leaded 1500W > 1.5KE series. Description

Size: px
Start display at page:

Download "1.5KE Series. Transient Voltage Suppression Diodes. Axial Leaded 1500W > 1.5KE series. Description"

Transcription

1 1.5KE Series RoHS Pb e3 Description Uni-directional The 1.5KE Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Agency Approvals AGENCY AGENCY FILE NUMBER E23531 Parameter Symbol Value Unit Peak Pulse Power Dissipation by 1/μs Test Waveform (Fig.2 (Note 1, (Note 4 P PPM 15 W Steady State Power Dissipation on Infinite Heat Sink at T L =75ºC Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2 Maximum Instantaneous Forward Voltage at A for Unidirectional Only (Note 3 Operating Junction and Storage Temperature Range Typical Thermal Resistance Junction to Lead Typical Thermal Resistance Junction to Ambient Bi-directional Maximum Ratings and Thermal Characteristics (T A =25 O C unless otherwise noted P D 6.5 W I FSM 2 A V F 3.5/5. V T J, T STG -55 to 175 C R θjl 15 C/W R θja 75 C/W Features 15W peak pulse capability at 1/μs waveform, repetition rate (duty cycles:.1% Glass passivated chip junction in DO-21 Package Fast response time: typically less than 1.ps from Volts to BV min Excellent clamping capability Typical failure mode is short from over-specified voltage or current Whisker test is conducted based on JEDEC JESD21A per its table 4a and 4c IEC ESD 3kV(Air, 3kV (Contact ESD protection of data lines in accordance with IEC EFT protection of data lines in accordance with IEC Low incremental surge resistance Typical I R less than 1μA when V BR min>12v High temperature to reflow soldering guaranteed: 26 C/4sec /.375,(9.5mm lead length, 5 lbs., (2.3kg tension V T J = V C x (1+αT x (T J - 25 (αt:temperature Coefficient, typical value is.1% Plastic package is flammability rated V- per Underwriters Laboratories Matte tin lead free plated Halogen free and RoHS compliant Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(sn (IPC/JEDEC J-STD- 69A.1 Notes: 1. Non-repetitive current pulse, per Fig. 4 and derated above T J (initial =25 O C per Fig Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. 3. V F < 3.5V for single die parts and V F < 5.V for stacked-die parts. 4. The P PPM of stacked-die parts is 2kW and please contact littelfuse for the detail stacked-die parts. Functional Diagram Applications TVS devices are ideal for the protection of I/O interfaces, V CC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Additional Infomarion Bi-directional Datasheet Resources Samples Cathode Anode Uni-directional

2 Electrical Characteristics (T A =25 C unless otherwise noted Part Number (Uni Part Number (Bi Reverse Stand off Voltage V R (Volts Breakdown Voltage V BR I T MIN MAX Test Current I T (ma Maximum Clamping Voltage V I pp (Volts Maximum Peak Pulse Current I pp (A Maximum Reverse Leakage I V R (µa 1.5KE6.8A 1.5KE6.8CA X 1.5KE7.5A 1.5KE7.5CA X 1.5KE8.2A 1.5KE8.2CA X 1.5KE9.1A 1.5KE9.1CA X 1.5KE1A 1.5KE1CA X 1.5KE11A 1.5KE11CA X 1.5KE12A 1.5KE12CA X 1.5KE13A 1.5KE13CA X 1.5KE15A 1.5KE15CA X 1.5KE16A 1.5KE16CA X 1.5KE18A 1.5KE18CA X 1.5KE2A 1.5KE2CA X 1.5KE22A 1.5KE22CA X 1.5KE24A 1.5KE24CA X 1.5KE27A 1.5KE27CA X 1.5KE3A 1.5KE3CA X 1.5KE33A 1.5KE33CA X 1.5KE36A 1.5KE36CA X 1.5KE39A 1.5KE39CA X 1.5KE43A 1.5KE43CA X 1.5KE47A 1.5KE47CA X 1.5KE51A 1.5KE51CA X 1.5KE56A 1.5KE56CA X 1.5KE62A 1.5KE62CA X 1.5KE68A 1.5KE68CA X 1.5KE75A 1.5KE75CA X 1.5KE82A 1.5KE82CA X 1.5KE91A 1.5KE91CA X 1.5KEA 1.5KECA X 1.5KE11A 1.5KE11CA X 1.5KE12A 1.5KE12CA X 1.5KE13A 1.5KE13CA X 1.5KE15A 1.5KE15CA X 1.5KE16A 1.5KE16CA X 1.5KE17A 1.5KE17CA X 1.5KE18A 1.5KE18CA X 1.5KE2A 1.5KE2CA X 1.5KE22A 1.5KE22CA X 1.5KE25A 1.5KE25CA X 1.5KE3A 1.5KE3CA X 1.5KE32A 1.5KE32CA X 1.5KE35A 1.5KE35CA X 1.5KE4A 1.5KE4CA X 1.5KE44A 1.5KE44CA X 1.5KE48A 1.5KE48CA KE51A 1.5KE51CA KE53A 1.5KE53CA KE54A 1.5KE54CA KE55A 1.5KE55CA KE6A 1.5KE6CA F For bidirectional type having V R of 1 volts and less, the I R limit is double. For parts without A, the V BR is ± 1% and V C is 5% higher than with A parts. Agency Approval

3 I-V Curve Characteristics Uni-directional Bi-directional Ipp Vc VBR VR IR IT VF V Vc VBR VR IT IR IR IT VRVBR Vc V Ipp Ipp P PPM Peak Pulse Power Dissipation -- Max power dissipation V R Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation V BR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (I T V C Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current I R V F Reverse Leakage Current -- Current measured at V R Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T A =25 C unless otherwise noted Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS P PPM -Peak Pulse Power (kw 1 1 Single die, 1.5kW at 1xµs, 25 C stacked-die, 2kW at 1xµs, 25 C TJ initial = Tamb Time t d -Pulse Width (ms continues on next page.

4 Ratings and Characteristic Curves (T A =25 C unless otherwise noted (Continued Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform Peak Pulse Power (P PP or Current (I PP Derating in Percentage % T J - Initial Junction Temperature (ºC I PPM - Peak Pulse Current, % I RSM 15 5 td tr=1µsec Peak Value IPPM Half Value IPPM 2 IPPM ( TJ=25 C Pulse Width(td is defined as the point where the peak current decays to 5% of IPPM 1/µsec. Waveform as defined by R.E.A t-time (ms Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance Cj(pF 1 Uni-directional V=V Bi-directional V=V Uni-directional V=V R Bi-directional V=V R Transient Thermal Impedance ( C/W V BR -Reverse Breakdown Voltage(V Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only T P -Pulse Duration (s Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values I FSM - Peak Forward Surge Current (A I F -Peak Forward Current(A Single die Stacked-die 1 1 Number of Cycles at 6 Hz V F -Peak Forward Voltage(V

5 Temperature (T Transient Voltage Suppression Diodes Soldering Parameters Reflow Condition Lead free assembly t p Pre Heat - Temperature Min (T s(min 15 C - Temperature Max (T s(max 2 C T P T L Ramp-up t L Critical Zone T L to T P - Time (min to max (t s 6 18 secs T s(max Average ramp up rate (Liquidus Temp (T A to peak T S(max to T A - Ramp-up Rate 3 C/second max 3 C/second max T s(min t s Preheat Ramp-down Reflow - Temperature (T A (Liquidus 217 C - Time (min to max (t s 6 15 seconds 25 C t 25 C to Peak Time (t Peak Temperature (T P 26 +/-5 C Time within 5 C of actual peak Temperature (t p 2 4 seconds Flow/Wave Soldering (Solder Dipping Ramp-down Rate 6 C/second max Peak Temperature : 265 O C Time 25 C to peak Temperature (T P 8 minutes Max. Dipping Time : 1 seconds Do not exceed 26 C Soldering : 1 time Physical Specifications Environmental Specifications Weight.45oz., 1.2g High Temp. Storage JESD22-A13 Case JEDEC DO-21 molded plastic body over passivated junction. HTRB JESD22-A18 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A14 Terminal Matte Tin axial leads, solderable per JESD22-B12. H3TRB JESD22-A11 RSH JESD22-B16 Dimensions A D Cathode Band (for Uni-directional products only B DO-21 A C Dimensions Inches Millimeters Min Max Min Max A B C D

6 Part Numbering System Part Marking System 1.5KE xxx XXX OPTION CODE: BLANK Reel Tape -B Bulk Packaging TYPE CODE: A Uni-Directional (5% V BR Voltage Tolerance CA Bi-Directional (5% V BR Voltage Tolerance V BR VOLTAGE CODE (Refer to the Electrical Characteristics table SERIES CODE Cathode Band (for Uni-directional products only Littelfuse Logo F YYWW 1.5KEXXX Trace Code Marking YY:Year Code WW: Week Code Product Type Packaging Part Number Component Package Quantity Packaging Option Packaging Specification 1.5KExxxXX DO Tape & Reel EIA STD RS KExxxXX-B DO-21 5 BULK Littelfuse Spec. Tape and Reel Specification 2.56 (65. Off Center either side.28( /-.39 (53.+2./ /-.2 (1.+/ ( ( (6. Dimensions are in inches/mm 3. ( ( (17.27 Recess Depth Max..75 (19.5 Direction of Feed

SLD Series. Transient Voltage Suppression Diodes Axial Leaded 2200W > SLD series. Description. Uni-directional

SLD Series. Transient Voltage Suppression Diodes Axial Leaded 2200W > SLD series. Description. Uni-directional SLD Series RoHS Pb e3 Description The AEC-Q qualified SLD Series is packaged in a highly reliable industry standard P6 axial leaded package and is designed to provide precision overvoltage protection for

More information

TPSMC Series. TVS Diodes Surface Mount 1500W > TPSMC series. Description. Uni-directional Bi-directional

TPSMC Series. TVS Diodes Surface Mount 1500W > TPSMC series. Description. Uni-directional Bi-directional TPSMC Series RoHS Pb e3 Uni-directional Bi-directional Description The TPSMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other

More information

5.0SMDJ Series. Transient Voltage Suppression Diodes. Surface Mount 5000W > 5.0SMDJ series. Description. Uni-directional

5.0SMDJ Series. Transient Voltage Suppression Diodes. Surface Mount 5000W > 5.0SMDJ series. Description. Uni-directional 5.SMDJ Series RoHS Pb e3 Uni-directional Description Bi-directional The 5.SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and

More information

Transient Voltage Suppression Diodes. Surface Mount 400W > SMAJ series. Description. Features. less than 1μA when V BR.

Transient Voltage Suppression Diodes. Surface Mount 400W > SMAJ series. Description. Features. less than 1μA when V BR. SMAJ Series RoHS Pb e3 Uni-directional Description Bi-directional The SMAJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other

More information

P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.com FEATURES PRIMARY CHARACTERISTICS

P6KE6.8A thru P6KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.com FEATURES PRIMARY CHARACTERISTICS TRANSZORB Transient Voltage Suppressors DO-204AC (DO-15) PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 540 V V BR bi-directional 6.8 V to 440 V P PPM 600 W P D 5.0 W I FSM (uni-directional

More information

SM712 Series 600W Asymmetrical TVS Diode Array

SM712 Series 600W Asymmetrical TVS Diode Array SM712 Series 6W Asymmetrical TVS Diode Array RoHS Pb GREEN Description The SM712 TVS Diode Array is designed to protect RS-485 applications with asymmetrical working voltages (-7V to from damage due to

More information

1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay.

1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. www.vishay. TRANSZORB Transient Voltage Suppressors Case Style.5KE FEATURES Glass passivated chip junction Available in uni-directional and bi-directional 500 W peak pulse power capability with a /0 μs waveform, repetitive

More information

Description YD/T 950. YD/T 993 YD/T 1082 GR 1089 Inter-building GR 1089 Intra-building IEC 61000-4-2 V V DRM. @250V/µs I H

Description YD/T 950. YD/T 993 YD/T 1082 GR 1089 Inter-building GR 1089 Intra-building IEC 61000-4-2 V V DRM. @250V/µs I H SDP Series - SOT23-5 RoHS Pb e3 Description This new SIDACtor series is targeted for the tertiary or line driver side protection position for VDSL2+, ADSL2 applications and general I/O protection functions.

More information

SM Series 400W TVS Diode Array

SM Series 400W TVS Diode Array General Purpose ESD Protection - SM5 through SM3 SM Series W TVS Diode Array RoHS Pb GREEN Description The SM series TVS Diode Array is designed to protect sensitive equipment from damage due to electrostatic

More information

SMDJ Series. Transient Voltage Suppression Diodes. Surface Mount 3000W > SMDJ series. Description. Uni-directional

SMDJ Series. Transient Voltage Suppression Diodes. Surface Mount 3000W > SMDJ series. Description. Uni-directional SMDJ Series RoHS Pb e3 Uni-directional Description Bi-directional The SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other

More information

SDC15. TVS Diode Array for ESD Protection of 12V Data and Power Lines. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics

SDC15. TVS Diode Array for ESD Protection of 12V Data and Power Lines. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics Description The SDC15 transient voltage suppressor (TVS) is designed to protect components which are connected to data and transmission lines from voltage surges caused by electrostatic discharge (ESD),

More information

SM712. Asymmetrical TVS Diode for Extended Common-Mode RS-485. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics.

SM712. Asymmetrical TVS Diode for Extended Common-Mode RS-485. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics. Description The SM712 transient voltage suppressor (TVS) diode is designed for asymmetrical (12V to 7V ) protection in multipoint data transmission standard RS485 applications. The SM712 may be used to

More information

Surface Mount 3000 Watt Transient Voltage Suppressor

Surface Mount 3000 Watt Transient Voltage Suppressor MSMLG5.0A MSMLG70CAe3, MSMLJ5.0 MSMLJ70CAe3 Available Surface Mount 3000 Watt Transient Voltage Suppressor DESCRIPTION The MSMLG(J)5.0A through MXLSMLG(J)70A series of high-reliability Transient Voltage

More information

General Purpose Plastic Rectifier

General Purpose Plastic Rectifier General Purpose Plastic Rectifier N400 thru N4007 DO-204AL (DO-4) FEATURES Low forward voltage drop Low leakage current High forward surge capability Solder dip 275 C max. s, per JESD 22-B6 Compliant to

More information

UF4001, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier

UF4001, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007  Ultrafast Plastic Rectifier UF400, UF4002, UF4003, UF4004, UF4005, UF4006, UF4007 Ultrafast Plastic Rectifier FEATURES Glass passivated chip junction Ultrafast reverse recovery time Low forward voltage drop Low switching losses,

More information

SR70 RailClamp Low Capacitance TVS Diode Array

SR70 RailClamp Low Capacitance TVS Diode Array RailClamp Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. The SR7 has been specifically designed to protect sensitive components which are connected

More information

Surface Mount Schottky Barrier

Surface Mount Schottky Barrier FEATURES - Very low profile - typical height of 0.68mm - Low power loss, high efficiency - Ideal for automated placement - Moisture sensitivity level: level, per J-STD-020 - Compliant to RoHS Directive

More information

Surface Mount ESD Capability Rectifiers

Surface Mount ESD Capability Rectifiers SE0PB thru SE0PJ Surface Mount ESD Capability Rectifiers esmp TM Series DO-220AA (SMP) PRIMARY CHARACTERISTICS I F(AV).0 A V RRM 00 V to 600 V I R 5 µa V F at I F =.0 A 0.86 V T J max. 75 C TYPICAL APPLICATIONS

More information

SIDACtor Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor Series - TO-92. Description

SIDACtor Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor Series - TO-92. Description SIACtor Series - TO-92 RoHS Pb e3 escription SIACtor Series TO-92 are designed to protect baseband equipment such as modems, line cards, CPE and SL from damaging overvoltage transients. The series provides

More information

Voidless Hermetically Sealed Bidirectional Transient Voltage Suppressors Qualified to MIL-PRF-19500/516

Voidless Hermetically Sealed Bidirectional Transient Voltage Suppressors Qualified to MIL-PRF-19500/516 Available on commercial versions Voidless Hermetically Sealed Bidirectional Transient Voltage Suppressors Qualified to MIL-PRF-19500/516 DESCRIPTION This series of industry recognized voidless, hermetically

More information

LC03-6. Low Capacitance TVS for High-Speed Data Interfaces. Features. Description. Mechanical Characteristics. Applications

LC03-6. Low Capacitance TVS for High-Speed Data Interfaces. Features. Description. Mechanical Characteristics. Applications Description The LC0- transient voltage suppressor is designed to protect components which are connected to high speed telecommunication lines from voltage surges caused by lightning, electrostatic discharge

More information

SP724 Series 3pF 8kV Diode Array

SP724 Series 3pF 8kV Diode Array SP74 Series pf 8kV Diode Array RoHS Pb GREEN Description The SP74 is a quad array of transient voltage clamping circuits designed to suppress ESD and other transient overvoltage events. The SP74 is used

More information

SM9992DSQG. Features. Ordering and Marking Information. Dual N-Channel Enhancement Mode MOSFET 20V/12A, R DS(ON) =4.5V =4V =3.7V =3.

SM9992DSQG. Features. Ordering and Marking Information. Dual N-Channel Enhancement Mode MOSFET 20V/12A, R DS(ON) =4.5V =4V =3.7V =3. Dual N-Channel Enhancement Mode MOSFET Features 20V/12, =8.1mΩ (Max.) @ =4.5V =8.5mΩ (Max.) @ =4V =8.8mΩ (Max.) @ =3.7V =9.2mΩ (Max.) @ =3.1V =11mΩ (Max.) @ =2.5V Reliable and Rugged Lead Free and Green

More information

1SMC5352 Taiwan Semiconductor

1SMC5352 Taiwan Semiconductor 5W, 15V Surface Mount Zener Diode FEATURES - Low profile package - Ideal for automated placement - Glass passivated junction - Built-in strain relief - Compliant to RoHS Directive 2011/65/EU and in accordance

More information

1SMA5.0AT3G Series, SZ1SMA5.0AT3G Series. 400 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional

1SMA5.0AT3G Series, SZ1SMA5.0AT3G Series. 400 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional .AT3G Series, SZ.AT3G Series 4 Watt Peak Power Zener Transient Voltage Suppressors Unidirectional The series is designed to protect voltage sensitive components from high voltage, high energy transients.

More information

Surface Mount TRANSZORB Transient Voltage Suppressors

Surface Mount TRANSZORB Transient Voltage Suppressors Surface Mount TRANSZORB Transient Voltage Suppressors DO-214AA (SMB J-Bend) PRIMARY CHARACTERISTICS V BR (bi-directional) 6.4 V to 231 V V BR (uni-directional) 6.4 V to 231 V V WM 5.0 V to 188 V P PPM

More information

STIEC45-xxAS, STIEC45-xxACS

STIEC45-xxAS, STIEC45-xxACS Transil TVS for IEC 61000-4-5 compliance Datasheet - production data differential mode MIL STD 883G, method 3015-7 Class 3B 25 kv HBM (human body model) Resin meets UL 94, V0 MIL-STD-750, method 2026 solderability

More information

3EZ6.2D5 Series. 3 Watt DO-41 Surmetic 30 Zener Voltage Regulators

3EZ6.2D5 Series. 3 Watt DO-41 Surmetic 30 Zener Voltage Regulators EZ6.D Series Watt DO- Surmetic Zener Voltage Regulators This is a complete series of Watt Zener diodes with limits and excellent operating characteristics that reflect the superior capabilities of silicon-oxide

More information

PDS5100H. Product Summary. Features and Benefits. Mechanical Data. Description and Applications. Ordering Information (Note 5) Marking Information

PDS5100H. Product Summary. Features and Benefits. Mechanical Data. Description and Applications. Ordering Information (Note 5) Marking Information Green 5A HIGH VOLTAGE SCHOTTKY BARRIER RECTIFIER POWERDI 5 Product Summary I F V R V F MAX (V) I R MAX (ma) (V) (A) @ +25 C @ +25 C 1 5..71.35 Description and Applications This Schottky Barrier Rectifier

More information

LC05-6. Dual Low Capacitance TVS Array for Telecom Line-Card Applications. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics

LC05-6. Dual Low Capacitance TVS Array for Telecom Line-Card Applications. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics Description The LC5-6 has been specifically designed to protect sensitive components which are connected to highspeed telecommunications lines from over voltages caused by lightning, electrostatic discharge

More information

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description

Metal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four

More information

Gas Discharge Tube (GDT) Products CG5 and SL0902A Series. CG5 and SL0902A Series

Gas Discharge Tube (GDT) Products CG5 and SL0902A Series. CG5 and SL0902A Series Description Agency Approvals AGENCY AGENCY FILE NUMBER E128662 2 Electrode GDT Graphical Symbol Littelfuse Broadband Optimized SL0902A Series offers high surge ratings in a miniature package. Special design

More information

ESDAxxL DUAL TRANSIL ARRAY FOR ESD PROTECTION

ESDAxxL DUAL TRANSIL ARRAY FOR ESD PROTECTION Application Specific Discretes A.S.D. ESDAxxL DUAL TRANSIL ARRAY FOR ESD PROTECTION APPLICATIONS Where transient overvoltage protection in ESD sensitive equipment is required, such as : - COMPUTERS - PRINTERS

More information

1N59xxBRNG Series. 3 W DO-41 Surmetic 30 Zener Voltage Regulators

1N59xxBRNG Series. 3 W DO-41 Surmetic 30 Zener Voltage Regulators W DO-4 Surmetic 0 Zener Voltage Regulators This is a N9xxBRNG series with limits and excellent operating characteristics that reflect the superior capabilities of silicon oxide passivated junctions. All

More information

SM4953K. Features. Ordering and Marking Information. Dual P-Channel Enhancement Mode MOSFET -30V/-4.9A, R DS(ON) =53mW(typ.

SM4953K. Features. Ordering and Marking Information. Dual P-Channel Enhancement Mode MOSFET -30V/-4.9A, R DS(ON) =53mW(typ. Dual P-Channel Enhancement Mode MOSFET Features Pin Description -30V/-4.9, R DS(ON) =53mW(typ.) @ V GS =-10V R DS(ON) =80mW(typ.) @ V GS =-4.5V Reliable and Rugged Lead Free and Green Device vailable (RoHS

More information

RClamp0582BQ. Low Capacitance TVS for Automotive Applications. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp0582BQ. Low Capacitance TVS for Automotive Applications. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics - RailClamp Description The RClamp 582BQ transient voltage suppressor is specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage

More information

SR2.8 RailClamp Low Capacitance TVS Diode Array

SR2.8 RailClamp Low Capacitance TVS Diode Array Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. The SR series has been specifically designed to protect sensitive components which are connected to data

More information

SESD Series Ultra Low Capacitance Discrete TVS

SESD Series Ultra Low Capacitance Discrete TVS SESD Series Ultra Low apacitance Discrete TVS RoHS Pb GREEN ELV Description The SESD Series Ultra Low apacitance Discrete TVS provides unidirectional and bidirectional ESD protection for the world s most

More information

RClamp2402B. Ultra-Low Capacitance TVS for ESD and CDE Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp2402B. Ultra-Low Capacitance TVS for ESD and CDE Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics - RailClamp Description RailClamps are ultra low capacitance TS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are

More information

1.5SMC6.8AT3G Series, SZ1.5SMC6.8AT3G Series. 1500 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional*

1.5SMC6.8AT3G Series, SZ1.5SMC6.8AT3G Series. 1500 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional* .6.8AT3G Series, SZ.6.8AT3G Series 00 Watt Peak Power Zener Transient Voltage Suppressors Unidirectional* The series is designed to protect voltage sensitive components from high voltage, high energy transients.

More information

VOIDLESS HERMETICALLY SEALED SWITCHING DIODES Qualified per MIL-PRF-19500/578

VOIDLESS HERMETICALLY SEALED SWITCHING DIODES Qualified per MIL-PRF-19500/578 Available on commercial versions VOIDLESS HERMETICALLY SEALED SWITCHING DIODES Qualified per MIL-PRF-19500/578 DESCRIPTION These popular JEDEC registered switching/signal diodes are military qualified

More information

RClamp0502A RailClamp Low Capacitance TVS Array

RClamp0502A RailClamp Low Capacitance TVS Array - RailClamp Description The RailClamp series consists of ultra low capacitance TS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive

More information

1SMB59xxBT3G Series, SZ1SMB59xxT3G Series. 3 Watt Plastic Surface Mount Zener Voltage Regulators

1SMB59xxBT3G Series, SZ1SMB59xxT3G Series. 3 Watt Plastic Surface Mount Zener Voltage Regulators 9xxBTG Series, SZ9xxTG Series Watt Plastic Surface Mount Zener Voltage Regulators This complete new line of W Zener diodes offers the following advantages. Features Zener Voltage Range. V to V ESD Rating

More information

1N5333B Series. 5 Watt Surmetic 40 Zener Voltage Regulators

1N5333B Series. 5 Watt Surmetic 40 Zener Voltage Regulators Preferred Device Watt Surmetic 40 Zener Voltage Regulators This is a complete series of Watt Zener diodes with tight limits and better operating characteristics that reflect the superior capabilities of

More information

RClamp0504P RailClamp Low Capacitance TVS Array

RClamp0504P RailClamp Low Capacitance TVS Array - RailClamp Description RailClamps are low capacitance TVS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected

More information

Surface Mount ESD Capability Rectifiers

Surface Mount ESD Capability Rectifiers Surface Mount ESD Capability Rectifiers Top View SlimSMA DO-22AC PRIMARY CHARACTERISTICS I F(AV) 3.0 A V RRM V, 200 V, 400 V, 600 V I FSM 40 A V F at I F = 3.0 A (T A = 25 C) 0.86 V I R μa T J max. 75

More information

TESDC24V Taiwan Semiconductor

TESDC24V Taiwan Semiconductor Bi-directional TS Diode Array FEATURES - Meet IEC61-4-2 (ESD) ±15k (air), ±8k (contact) 6 - Meet IEC61-4-4 (EFT) rating. A (5/5ns) 3 - Protects one Bi-directional I/O line 5 - Working oltage : 24 4 - Pb

More information

Surface Mount TRANSZORB Transient Voltage Suppressors

Surface Mount TRANSZORB Transient Voltage Suppressors Surface Mount TRANSZORB Transient Voltage Suppressors DO-214AB (SMC) PRIMARY CHARACTERISTICS V BR uni-directional 6.40 V to 209 V V BR bi-directional 6.40 V to 209 V V WM 5.0 V to 170 V P PPM 1500 W I

More information

RClamp3304NA RailClamp 3.3V TVS Arrays

RClamp3304NA RailClamp 3.3V TVS Arrays - RailClamp Description RailClamp low capacitance TVS array is designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected

More information

Features. Applications. Truth Table. Close

Features. Applications. Truth Table. Close ASSR-8, ASSR-9 and ASSR-8 Form A, Solid State Relay (Photo MOSFET) (0V/0.A/0Ω) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically

More information

RClamp0582B. Low Capacitance TVS for ESD and Surge Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp0582B. Low Capacitance TVS for ESD and Surge Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics - RailClamp Description RailClamp TS diodes are specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage caused by ESD (electrostatic

More information

SP724. TVS Diode Arrays

SP724. TVS Diode Arrays The is a quad array of transient voltage clamping circuits designed to suppress ESD and other transient over-voltage events. The is used to help protect sensitive digital or analog input circuits on data,

More information

Surface Mount TRANSZORB Transient Voltage Suppressors

Surface Mount TRANSZORB Transient Voltage Suppressors Surface Mount TRANSZORB Transient Voltage Suppressors DO-214AB (SMC) PRIMARY CHARACTERISTICS V BR uni-directional 6.40 V to 231 V V BR bi-directional 6.40 V to 231 V V WM 5.0 V to 188 V P PPM 1500 W P

More information

RClamp0502BA. Ultra-Low Capacitance TVS for ESD and CDE Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp0502BA. Ultra-Low Capacitance TVS for ESD and CDE Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics - RailClamp Description RailClamp TS diodes are specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage caused by ESD (electrostatic

More information

EVERLIGHT ELECTRONICS CO., LTD. Technical Data Sheet 0805 Package Chip LED Preliminary

EVERLIGHT ELECTRONICS CO., LTD. Technical Data Sheet 0805 Package Chip LED Preliminary Feature RoHS compliant. This is a preliminary specification Chip LED package. intended for design purposes and Colorless clear resin. Wide viewing angle 130 o. subject to change without prior Brightness:

More information

SMF05C. TVS Diode Array For ESD and Latch-Up Protection PRELIMINARY. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics

SMF05C. TVS Diode Array For ESD and Latch-Up Protection PRELIMINARY. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics Description The SMF series TVS arrays are designed to protect sensitive electronics from damage or latchup due to ESD and other voltageinduced transient events. They are designed for use in applications

More information

P6KE. Transil, transient voltage surge suppressor (TVS) Features. Description. Complies with the following standards

P6KE. Transil, transient voltage surge suppressor (TVS) Features. Description. Complies with the following standards Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 600 W (10/0 µs ) Stand-off voltage range 6.8 to 440 V Unidirectional and bidirectional types Low clamping

More information

Features DNC DNC GND GND GND GND GATE GATE. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel ZXGD3108N8TC ZXGD ,500

Features DNC DNC GND GND GND GND GATE GATE. Product Marking Reel Size (inches) Tape Width (mm) Quantity per Reel ZXGD3108N8TC ZXGD ,500 V ACTIVE OR'ING MOSFET CONTROLLER IN SO8 Description is a V Active OR ing MOSFET Controller designed for driving a very low R DS(ON) Power MOSFET as an ideal diode. This replaces the standard rectifier

More information

30BQ040 SCHOTTKY RECTIFIER. I F(AV) = 3.0Amp V R = 40V. Bulletin PD rev. G 07/04. Description/ Features. Major Ratings and Characteristics

30BQ040 SCHOTTKY RECTIFIER. I F(AV) = 3.0Amp V R = 40V. Bulletin PD rev. G 07/04. Description/ Features. Major Ratings and Characteristics 30BQ040 SCHOTTKY RECTIFIER 3 Amp I F(AV) = 3.0Amp V R = 40V Major Ratings and Characteristics Characteristics 30BQ040 Units I F(AV) Rectangular 3.0 A waveform V RRM 40 V I FSM @ t p = 5 µs sine 2000 A

More information

SMS3.3. 3.3 Volt TVS Array For ESD and Latch-Up Protection. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics.

SMS3.3. 3.3 Volt TVS Array For ESD and Latch-Up Protection. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics. Description The SMS series of TS arrays are designed to protect sensitive electronics from damage or latch-up due to ESD, lightning, and other voltage-induced transient events. Each device will protect

More information

DISCONTINUED. Product Marking Reel size (inches) Tape width (mm) Quantity per reel DMN4015LK3-13 N4015L ,500

DISCONTINUED. Product Marking Reel size (inches) Tape width (mm) Quantity per reel DMN4015LK3-13 N4015L ,500 40V N-CHANNEL ENHANCEMENT MODE MOSFET Product Summary V (BR)DSS 40V T A = 25 C 5mΩ @ = V 20.8A 20mΩ @ = 4.5V 8.0A Description and Applications This new generation MOSFET has been designed to minimize the

More information

BZW50. Transil, transient voltage surge suppressor (TVS) Features. Description

BZW50. Transil, transient voltage surge suppressor (TVS) Features. Description Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 5000 W (10/0 µs) Stand-off voltage range from 10 V to 180 V Unidirectional and bidirectional types

More information

DISCONTINUED. Product Marking Reel size (inches) Tape width (mm) Quantity per reel DMN4009LK3-13 N4009L ,500

DISCONTINUED. Product Marking Reel size (inches) Tape width (mm) Quantity per reel DMN4009LK3-13 N4009L ,500 40V N-CHANNEL ENHANCEMENT MODE MOSFET Product Summary V (BR)DSS 40V R DS(on) T A = 25 C 8.5mΩ @ = V 27.6A 4mΩ @ = 4.5V 2.5A Description and Applications This new generation MOSFET has been designed to

More information

LC04-6. Dual Low Capacitance TVS Array for Telecom Linecard Applications. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics

LC04-6. Dual Low Capacitance TVS Array for Telecom Linecard Applications. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics Description The LC4-6 has been specifically designed to protect sensitive components which are connected to highspeed telecommunications lines from over voltages caused by lightning, electrostatic discharge

More information

General Purpose ESD Protection - SP1003 Series. Description. Features. Applications. Mobile phones Smart phones PDAs Portable navigation devices

General Purpose ESD Protection - SP1003 Series. Description. Features. Applications. Mobile phones Smart phones PDAs Portable navigation devices General Purpose ESD Protetion - SP003 Series SP003 Series - 30pF 30kV Unidiretional Disrete TVS RoHS Pb GREEN Desription Zener diodes fabriated in a proprietary silion avalanhe tehnology protet eah I/O

More information

uclamp3312t Low Voltage μclamp for Gigabit Ethernet

uclamp3312t Low Voltage μclamp for Gigabit Ethernet - MicroClamp Description The μclamp 2T TVS diode is specifically designed to meet the performance requirements of Gigabit Ethernet interfaces. They are designed to protect sensitive PHY chips from damage

More information

MOC211M, MOC212M, MOC213M Small Ouline Optocouplers Transistor Output

MOC211M, MOC212M, MOC213M Small Ouline Optocouplers Transistor Output MOC2M, MOC22M, MOC23M Small Ouline Optocouplers Transistor Output Features UL Recognized (File #E90700, Volume 2) VDE Recognized (File #3666) (add option V for VDE approval, e.g., MOC2VM) Convenient Plastic

More information

Features. P-Channel Enhancement Mode MOSFET

Features. P-Channel Enhancement Mode MOSFET P-Channel Enhancement Mode MOSFET Features Pin Description -4V/-25, R DS(ON) = 4mΩ (typ.) @ V GS = -V R DS(ON) = 55mΩ (typ.) @ V GS = -5V Super High Dense Cell Design G D S Reliable and Rugged Lead Free

More information

RClamp0821P. Ultra-Low Capacitance 1-Line ESD protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp0821P. Ultra-Low Capacitance 1-Line ESD protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics - RailClamp Description The RailClamp family is a series of ultra low capacitance Transient oltage Suppressors (TS) designed to protect high speed data interfaces. This series has been specifically designed

More information

RClamp7524T. Low Capacitance RClamp. 4-Line Protection PRELIMINARY. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics

RClamp7524T. Low Capacitance RClamp. 4-Line Protection PRELIMINARY. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics PROTECTION PRODUCTS - RailClamp Description RailClamp TS arrays are ultra low capacitance ESD protection devices designed to protect high speed data interfaces. This series has been specifically engineered

More information

High Performance Schottky Rectifier, 1 A

High Performance Schottky Rectifier, 1 A High Performance Schottky Rectifier, A VS-MQNPbF Cathode Anode DO-24AC (SMA) PRODUCT SUMMARY Package DO-24AC (SMA) I F(AV) A V R V V F at I F.78 V I RM ma at 25 C T J max. 5 C Diode variation Single die

More information

RClamp0514M RailClamp Low Capacitance TVS Diode Array PRELIMINARY Features

RClamp0514M RailClamp Low Capacitance TVS Diode Array PRELIMINARY Features RailClamp Description RailClamps are ultra low capacitance TVS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are

More information

Features -2.4A -1.8A. Part Number Case Packaging DMC6070LND-7 POWERDI ,000/Tape & Reel DMC6070LND-13 POWERDI ,000/Tape & Reel

Features -2.4A -1.8A. Part Number Case Packaging DMC6070LND-7 POWERDI ,000/Tape & Reel DMC6070LND-13 POWERDI ,000/Tape & Reel YYWW ADVANCED NEW PRODUCT INFORMATION COMPLEMENTARY PAIR ENHANCEMENT MODE MOSFET POWERDI Product Summary Device V (BR)DSS R DS(ON) max Q 6V Q -6V I D max T A = +5 C 85mΩ @ V = V 3.A mω @ V = 4.5V.7A 5mΩ

More information

FOD814 Series, FOD817 Series 4-Pin High Operating Temperature Phototransistor Optocouplers

FOD814 Series, FOD817 Series 4-Pin High Operating Temperature Phototransistor Optocouplers FOD84 Series, Series 4-Pin High Operating Temperature Phototransistor Optocouplers Features AC input response (FOD84 only) Applicable to Pb-free IR reflow soldering Compact 4-pin package Current transfer

More information

Dual Common-Cathode Ultrafast Plastic Rectifier

Dual Common-Cathode Ultrafast Plastic Rectifier (F,B)6AT thru (F,B)6JT Dual Common-Cathode Ultrafast Plastic Rectifier TO-0AB 6xT PIN PIN 3 PIN CASE 3 TO-63AB ITO-0AB F6xT PIN PIN 3 PIN 3 FEATURES Glass passivated chip junction Ultrafast recovery time

More information

VOIDLESS HERMETICALLY SEALED STANDARD RECOVERY GLASS RECTIFIERS. Qualified to MIL-PRF-19500/420

VOIDLESS HERMETICALLY SEALED STANDARD RECOVERY GLASS RECTIFIERS. Qualified to MIL-PRF-19500/420 Available on commercial versions VOIDLESS HERMETICALLY SEALED STANDARD RECOVERY GLASS RECTIFIERS Qualified to MIL-PRF-19500/420 DESCRIPTION This standard recovery rectifier diode series is military qualified

More information

Schottky Rectifier, 3.0 A

Schottky Rectifier, 3.0 A VS-30BQ060-M3 Schottky Rectifier, 3.0 A Cathode Anode SMC PRODUCT SUMMARY Package SMC I F(AV) 3.0 A V R 60 V V F at I F 0.52 V I RM 20 ma at 125 C T J max. 150 C Diode variation Single die E AS 5.0 mj

More information

Description/Features 5.59 (.220) 6.22 (.245) 6.60 (.260) 7.11 (.280).152 (.006).305 (.012) 2.00 (.079) 2.62 (.103).102 (.004) 0.76 (.030) 1.52 (.

Description/Features 5.59 (.220) 6.22 (.245) 6.60 (.260) 7.11 (.280).152 (.006).305 (.012) 2.00 (.079) 2.62 (.103).102 (.004) 0.76 (.030) 1.52 (. MBRS360TR SCHOTTKY RECTIFIER 3 Amp SMC Major Ratings and Characteristics Characteristics MBRS360TR Units I F(AV) Rectangular 3.0 A waveform V RRM 60 V I FSM @ t p = 5 µs sine 790 A V F @ 3.0 Apk, T = 25

More information

µclamp3601p TVS Diode for Proximity Switch Input Protection PROTECTION PRODUCTS - MicroClamp Description Features Mechanical Characteristics

µclamp3601p TVS Diode for Proximity Switch Input Protection PROTECTION PRODUCTS - MicroClamp Description Features Mechanical Characteristics PRTECTIN PRDUCTS - MicroClamp Description The µclamp P is a high-surge transient voltage suppressor (TVS) optimized for protection of sensitive digital sensors used in proximity switches and industrial

More information

SRDA3.3-6 and SRDA05-6 RailClamp Low Capacitance TVS Diode Array

SRDA3.3-6 and SRDA05-6 RailClamp Low Capacitance TVS Diode Array Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. The SR series has been specifically designed to protect sensitive components which are connected to data

More information

SZNUP2201MR6T1G SZNUP2201MR6. Transient Voltage Suppressors. ESD Protection Diodes with Low Clamping Voltage

SZNUP2201MR6T1G SZNUP2201MR6. Transient Voltage Suppressors. ESD Protection Diodes with Low Clamping Voltage NUP0MR, SZNUP0MR Transient Voltage Suppressors ESD Protection Diodes with Low Clamping Voltage The NUP0MR transient voltage suppressor is designed to protect high speed data lines from ESD, EFT, and lightning.

More information

Features. P d typ. (W) I max (A) 1206L005/60 f L010/60 n

Features. P d typ. (W) I max (A) 1206L005/60 f L010/60 n 1206L Series RoHS Description The 1206L Series PTC provides surface mount overcurrent protection for applications where space is at a premium and resettable protection is desired. Features RoHS compliant,

More information

High Performance Schottky Rectifier, 3.0 A

High Performance Schottky Rectifier, 3.0 A High Performance Schottky Rectifier, 3. A Cathode Anode SMC PRODUCT SUMMARY Package SMC I F(AV) 3. A V R 4 V V F at I F.46 V I RM 3 ma at 25 C T J max. 5 C Diode variation Single die E AS 6. mj FEATURES

More information

1N5820, 1N5821, 1N5822. Axial Lead Rectifiers SCHOTTKY BARRIER RECTIFIERS 3.0 AMPERES 20, 30, 40 VOLTS

1N5820, 1N5821, 1N5822. Axial Lead Rectifiers SCHOTTKY BARRIER RECTIFIERS 3.0 AMPERES 20, 30, 40 VOLTS 1N58, 1N5821, 1N5822 1N58 and 1N5822 are Preferred Devices Rectifiers This series employs the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features

More information

Schottky Rectifier, 1.0 A

Schottky Rectifier, 1.0 A Schottky Rectifier, 1.0 A VS-BQ040-M3 Cathode Anode PRODUCT SUMMARY Package SMB I F(AV) 1.0 A V R 40 V V F at I F 0.38 V I RM 9 ma at 125 C T J max. 150 C Diode variation Single die E AS 3.0 mj FEATURES

More information

Green. Part Number Compliance Case Packaging B340BQ-13-F Automotive SMB 3000/Tape & Reel B360BQ-13-F Automotive SMB 3000/Tape & Reel

Green. Part Number Compliance Case Packaging B340BQ-13-F Automotive SMB 3000/Tape & Reel B360BQ-13-F Automotive SMB 3000/Tape & Reel Green 3.0A SURFAE MOUNT SHOTTKY BARRIER RETIFIER Product Summary (@+25 ) B340BQ V RRM (V) I O (A) V F Max (V) I R Max (ma) 40 3.0 0.5 0.5 B360BQ V RRM (V) I O (A) V F Max (V) I R Max (ma) 60 3.0 0.7 0.5

More information

SLVU EPD TVS Diode Array For ESD and Latch-Up Protection PRELIMINARY. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics

SLVU EPD TVS Diode Array For ESD and Latch-Up Protection PRELIMINARY. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics Description The SL series of transient voltage suppressors are designed to protect low voltage, state-of-the-art CMOS semiconductors from transients caused by electrostatic discharge (ESD), cable discharge

More information

uclamp3301h Low Voltage μclamp TM for ESD and CDE Protection PRELIMINARY Features

uclamp3301h Low Voltage μclamp TM for ESD and CDE Protection PRELIMINARY Features PROTECTION PRODUCTS -MicroClamp Description The μclamp series of Transient Suppressors (TVS) are designed to replace multilayer varistors (MLVs) in portable applications such as cell phones, notebook computers,

More information

AUIRF6218S AUIRF6218L

AUIRF6218S AUIRF6218L AUTOMOTIVE GRADE AUIRF6218S AUIRF6218L Features Advanced Planar Technology Low On-Resistance P-Channel MOSFET Dynamic dv/dt Rating 175 C Operating Temperature Fast Switching Fully Avalanche Rated Repetitive

More information

LC03-6R2G. Low Capacitance Surface Mount TVS for High-Speed Data Interfaces. SO-8 LOW CAPACITANCE VOLTAGE SUPPRESSOR 2 kw PEAK POWER 6 VOLTS

LC03-6R2G. Low Capacitance Surface Mount TVS for High-Speed Data Interfaces. SO-8 LOW CAPACITANCE VOLTAGE SUPPRESSOR 2 kw PEAK POWER 6 VOLTS Low Capacitance Surface Mount TVS for High-Speed Data terfaces The LC3- transient voltage suppressor is designed to protect equipment attached to high speed communication lines from ESD, EFT, and lighting.

More information

High Performance Schottky Rectifier, 1.0 A

High Performance Schottky Rectifier, 1.0 A High Performance Schottky Rectifier, 1. A VS-BQ3-M3 Cathode Anode SMB PRODUCT SUMMARY Package SMB I F(AV) 1. A V R 3 V V F at I F.42 V I RM max. 15 ma at 125 C T J max. 15 C Diode variation Single die

More information

6.2 & 6.55 Volt Zener Reference Diodes

6.2 & 6.55 Volt Zener Reference Diodes 1N81-1 1N89A-1 Available on commercial versions 6. & 6.55 Volt Zener Reference Diodes Qualified per MIL-PRF-19500/9 DESCRIPTION *Qualified Levels: JAN, JANTX, JANTXV and JANS (available on some part numbers)

More information

ESD9X3.3ST5G Series, SZESD9X3.3ST5G Series. Transient Voltage Suppressors Micro Packaged Diodes for ESD Protection

ESD9X3.3ST5G Series, SZESD9X3.3ST5G Series. Transient Voltage Suppressors Micro Packaged Diodes for ESD Protection ESD9X3.3ST5G Series, SZESD9X3.3ST5G Series Transient Voltage Suppressors Micro Packaged Diodes for ESD Protection The ESD9X Series is designed to protect voltage sensitive components from ESD. Excellent

More information

RClamp0544M RailClamp ESD Protection for HDMI Interfaces PRELIMINARY Features

RClamp0544M RailClamp ESD Protection for HDMI Interfaces PRELIMINARY Features RailClamp Description RailClamps are ultra low capacitance TVS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are

More information

1SMB5.0AT3G Series, SZ1SMB5.0AT3G Series. 600 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional

1SMB5.0AT3G Series, SZ1SMB5.0AT3G Series. 600 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional 1SMBAT3G Series, SZ1SMBAT3G Series 600 Watt Peak Power Zener Transient Voltage Suppressors Unidirectional The SMB series is designed to protect voltage sensitive components from high voltage, high energy

More information

InGaN / Metal Alloy Warm White Water clear. Parameter Rating Unit

InGaN / Metal Alloy Warm White Water clear. Parameter Rating Unit Package Dimensions: * All dimensions are in mm * Tolerance: ±0.6mm unless otherwise noted. LED Chip Lens Colour Ant Part No. Material Colour Coordinates 703-0152 InGaN / Metal Alloy Warm White Water clear

More information

Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A

Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A Standard Recovery Diodes, Generation 2 DO-5 (Stud Version), 95 A 95PF(R)... DO-203AB (DO-5) PRODUCT SUMMARY I F(AV) Package Circuit configuration 95PF(R)...W DO-203AB (DO-5) 95 A DO-203AB (DO-5) Single

More information

Description. Product Structure. Nickle-plated copper lead and disk Epoxy resin body. Nickle-plated copper leadframe (Tin plate on exposed surfaces)

Description. Product Structure. Nickle-plated copper lead and disk Epoxy resin body. Nickle-plated copper leadframe (Tin plate on exposed surfaces) Series Features and Benefits DC blocking voltage, V DC, to 3 V Low V F (0.95 to.0 V max, at I F = 6 A) Low reverse leakage current, I R = 0 μa High temperature range Flammability: UL94V-0 (Equivalent)

More information

SEMICONDUCTOR GENERAL DATA

SEMICONDUCTOR GENERAL DATA MOTOROLA SEMICONDUCTOR TECHNICAL DATA 0 mw DO-35 Glass Zener Voltage Regulator Diodes GENERAL DATA APPLICABLE TO ALL SERIES IN THIS GROUP 0 Milliwatt Hermetically Sealed Glass Silicon Zener Diodes Specification

More information

Features. Case: TO-220-3 (2), TO-220F-3 (Option 1), TO-252-2 (1) and TO- 263-2 Power Management Instrumentation

Features. Case: TO-220-3 (2), TO-220F-3 (Option 1), TO-252-2 (1) and TO- 263-2 Power Management Instrumentation HIGH VOLTAGE POWER SCHOTTKY RECTIFIER Product Summary V F (MAX) (V) I R (MAX) (ma) V RRM (V) I O (A) @ +25 C @ +25 C 100 2x10 0.85 0.1 Description High voltage dual Schottky rectifier suited for switch

More information