Hardware Installation Guide
|
|
- Fay Greene
- 7 years ago
- Views:
Transcription
1 Hardware Installation Guide Toll-free: Tel. International: Allure EC-Sensor Series: Space temperature sensors. Product Description. General Installation Requirements The Allure EC-Sensor series of analog wall sensors is designed to interface with controllers of fan coil, heat pump, roof top and terminal heating / cooling units. These sensors provide precision local temperature measurement with the capability of local setpoint adjustment, fan speed setting, and occupancy override. Each sensor in this series has internal communications terminals to connect it to a LON or BACnet network. In addition, a built-in communications jack exists, allowing a user to connect a computer to the communication network without having to open the sensor s cover. In addition, through this communication jack, an EC-Smart- Sensor-VAV can be used as a hand-held balancing tool to perform VAV airflow calibration. The EC-Sensor s modern, alluring profile enclosure is suitable for classrooms, hotels, executive areas, office spaces and other commercial areas. Mounting hardware with a separate sub-base is provided with the device for installation on a dry wall or on an electrical junction box. This document describes the hardware installation procedures for the following device models: EC-Sensor, EC-Sensor-O, EC-Sensor- S, EC-Sensor-SO, and EC-Sensor-SOF. Unless otherwise indicated, the term EC-Sensor will be used in this document to represent all the models of the Allure EC-Sensor Series. For proper installation and subsequent operation of the EC-Sensor, pay special attention to the following recommendations: - Upon unpacking the product, inspect the contents of the carton for shipping damages. Do not install damaged sensors. - Allow for proper clearance of device enclosure and wiring terminals for easy access, hardware configuration and maintenance. - The device is designed to operate under the following environmental conditions: Ambient temperature from F to F (0 C to 0 C) Relative humidity from 0% to 90%, non-condensing. - Ensure proper ventilation of device and avoid areas where corroding, deteriorating or explosive vapors, fumes or gases may be present. The device must be oriented with the ventilation slots towards the top to permit proper heat dissipation. Any type of modification to any Distech Controls product will void the product s warranty. Take reasonable precautions to prevent electrostatic discharges to the device when installing, servicing or operating it. Discharge accumulated static electricity by touching one s hand to a securely grounded object before working with the device.. General Wiring Recommendations Turn off power before any kind of servicing. - All wiring must comply with electrical wiring diagrams as well as national and local electrical codes. - To connect the wiring to the device, use the terminal connectors which are located inside the device s enclosure. Use a small flat screwdriver to tighten the terminal connector screws once the wires have been inserted. - The board connectors accept wires or flat cables ranging from to AWG ( mm diameter) per pole. - It is recommended that all terminals be wired by 8AWG wire except for network communications. Figure -: EC-Sensor-SOF Distech Controls quality management system is ISO 900:000 certified
2 . Mounting Instructions. Device Components The EC-Sensor has been specially designed for easy installation. However, certain conditions apply when choosing a suitable location for the device: - Install the device in a location of average temperature approximately ft (. m) above the floor - The device should not be installed on an exterior wall. - The device should not be installed near a heat source. - The device should not be installed near an air discharge grill. - The device should not be installed in a place where it can be affected by the sun. - Install the device in an area that provides proper device ventilation. Nothing must restrain air circulation to the device. The EC-Sensor has not been designed for outdoor use. Wall Mounting Installation Procedure The EC-Sensor can be mounted on a dry wall using supplied screws. Remove the security screw from the device (Figure -).. Open the device by pressing in the two () tabs on the bottom of the device and pulling the bottom side of the front plate out.. Pull all cables 6 out of the wall, and insert them through the central hole of the back plate.. Align the back plate with the wall and mark the location of the mounting holes on the wall. Make sure to orient the proper side of the back plate facing upwards.. Remove the back plate and drill holes in the wall if necessary. 6. Install anchors in the wall if necessary. 7. Make sure that the mounting surface is flat and clean. 8. Screw the back plate onto the wall. Do not over tighten. 9. Strip each wire ¼ and insert each one according to the wiring diagrams shown in this document. 0. Gently push excess wiring back into the wall.. Reattach the front plate and make sure it clips tightly into place.. Install security screw. Electrical Junction box Installation Procedure The EC-Sensor can be mounted most American, European and Asian style electrical junction box using screws.. Remove the security screw from the device (Figure -).. Open the device by pressing in the two () tabs on the bottom of the device and pulling the bottom side of the front plate out.. Pull all cables 6 out of the wall, and insert them through the central hole of the back plate.. Screw the back plate onto the electrical junction box.. Strip each wire ¼ and insert each one according to the wiring diagrams shown in this document. 6. Gently push excess wiring back into the electrical junction box. 7. Reattach the front plate and make sure it clips tightly into place. 8. Install security screw. Figure -: Mounting a Smart-Sensor 6. Device Dimensions Unit Legend: mm (inches) Figure 6-: From top left to bottom: Front view, back plate, side view Toll-free: Tel. International:
3 WIRELESS HIGH 6 7. Device Wiring The EC-Sensor has physical connections for up to four () different features depending on the model. These features include the following: Thermistor Setpoint potentiometer Status indicator Fan speed rotary switch Wiring the 0kΩ Thermistor Terminals and MON are used for the 0kΩ type NTC thermistor, as well as for the override button (not available on EC-Sensor and EC-Sensor-S models). These two terminals are present on every EC-Sensor model. Input MON Figure 7-: 0kΩ NTC Thermistor input NTC Thermistor 0kΩ Override Button The override button creates a short circuit on the controller input, which is interpreted as an override signal. Wiring the 0kΩ Thermistor and the Setpoint Potentiometer Terminals and MON are used for the 0kΩ setpoint potentiometer. These terminals are present on the EC-Sensor-S, EC-Sensor-SO, and EC-Sensor-SOF models. Inputs MON NTC Thermistor 0kΩ Potentiometer 0kΩ Override Button Figure 7-: 0kΩ NTC Thermistor and setpoint potentiometer inputs Wiring a Status indicator Terminals and MON are used to connect a controller output to the status indicator. These terminals are present on the EC-Sensor-O, EC-Sensor-SO, and EC- Sensor-SOF. Vdc Output UO MON Figure 7-: Status indicator output Wiring a Five-Position Fan Speed Rotary Switch Terminals and MON are used to connect the five internal preset resistance values of the fan speed rotary switch to a controller input. These terminals are present on the EC-Sensor-SOF model. The following table shows the five fan speed settings and their corresponding resistance values. MON -position rotary switch Figure 7-: Five-position fan speed input resistors.kω.0kω 7.kΩ 0.0kΩ Wiring a EC-Smart-Sensor to a VAV for Air Flow Balancing (LON controllers only) The communications terminals ( and ) within the EC-Sensor can be connected to the and SMRTinputs of a VAV and facilitate VAV balancing with an EC- Smart-Sensor-VAV. In such a case, the EC-Sensor s communications jack would have to be used. To wire an EC-Smart-Sensor-VAV to a VAV via an EC- Sensor do the following:. Remove the front plate of the EC-. Connect the communications terminals ( and ) to the and SMRT- terminals of the VAV controller.. Remove the back plate of the EC-Smart-Sensor-VAV.. Connect the two () wires that terminate with the ⅛" audio cable to the and SMRT terminals of the EC-Smart-Sensor- VAV.. Insert the ⅛" audio cable into the communications jack of the EC- ECC-VAV LONWORKS LON LON SMRT- UO DO C- DO DO C- DO VAC V MON /8" SMRT Figure 7-: Wiring EC-Smart-Sensor to a VAV for airflow balancing The communications jack for both the EC-Smart-Sensor and EC-Sensor support mono and stereo audio cables. LON LON /8" Fan Speed Setting Auto Off Fan speed Fan speed Fan speed Corresponding Resistance Value 0Ω.kΩ.0kΩ 7.kΩ 0.0kΩ Toll-free: Tel. International:
4 WIRELESS HIGH 6 WIRELESS HIGH 6 Wiring an EC-Sensor to a LON network for Technician Use The communications terminals (, ) within the EC- Sensor can be optionally wired to a controller in a LON network To access the LON, a laptop can be connected to the EC-Sensor s communications jack by means of a ⅛" audio cable. If the distance between the EC-Sensor and the controller (Ttap length) is greater than 0ft (m), a bus topology must be used. The following figure shows how the EC-Sensor in bus topology LON network: AWG (0.6mm) unshielded twisted pair network cable The recommended cable type for LON communications is AWG (0.6mm), twisted pair, unshielded. The following figure shows how the EC-Sensor is connected in LON network with less than 0ft (m) T-tap length: Bus-topology network EC-Sensor AWG (0.6mm) unshielded twisted pair network cable <0ft (m) Bus-topology network Figure 7-6: LONWORKS Network Bus Topology with T-tap To wire a laptop to the LONWORKS network with T-tap via an EC-Sensor, do the following:. Remove the front plate of the EC-. Connect all three () LON cables coming from the previous device, going to the next device and going to the EC-Sensor to the LON and LON input terminals on the controller. If inserting multiple wires in the terminals, ensure to properly twist wires together prior to inserting them in the terminal connectors.. Connect the LON network cable coming from the controller to the and terminals on the EC-. Connect the two () wires that terminate with the ⅛" audio cable to the output terminals of the LonTalk adapter of the laptop.. Insert the ⅛" audio cable into the communications jack of the EC- ECC-VAV LONWORKS LON LON SMRT- UO DO C- DO DO C- DO VAC V From Previous To Next MON EC-Sensor Figure 7-8: LONWORKS Network Bus Topology To wire a laptop to a bus topology LONWORKS network via an EC-Sensor, do the following:. Remove the front plate of the EC-. Connect the LON cables coming from the previous device and going to the EC-Sensor to the LON and LON input terminals on the controller. If inserting multiple wires in the terminals, ensure to properly twist wires together prior to inserting them in the terminal connectors.. Connect the LON cables going to the next device and coming from the controller to the and input terminals on the EC- If inserting multiple wires in the terminals, ensure to properly twist wires together prior to inserting them in the terminal connectors.. Connect the two () wires that terminate with the ⅛" audio cable to the output terminals of the LonTalk adapter of the laptop.. Insert the ⅛" audio cable into the communications jack of the EC- ECC-VAV LONWORKS LON LON SMRT- UO DO C- DO DO C- DO VAC V From Previous To Next MON /8" /8" Figure 7-9: Wiring EC-Sensor to a LONWORKS Network Bus Topology Figure 7-7: Wiring EC-Sensor to a LONWORKS Network Bus Topology with T-tap For information and detailed explanations on network topology and wire length restrictions, please refer to the Junction Box and Wiring Guideline for Twisted Pair LONWORKS Networks, published by Echelon. Toll-free: Tel. International:
5 HIGH Wiring an EC-Sensor to a BACnet network for Technician Use The communications terminals (,, and ) within the EC-Sensor can be optionally wired to a controller in BACnet network. To access the BACnet networks, a laptop can be connected to the EC-Sensor s communications jack by means of a ⅛" audio cable. The recommended cable type for BACnet communication is AWG (0.mm), twisted pair, shielded. The following figure shows how the EC-Sensor is connected in BACnet network: ECB-VAV SUBNET VDC UO DO C- DO DO C- DO VAC V From Previous To Next MON /8" AWG (0.mm) shielded twisted pair network cable Bus-topology network EC-Sensor Figure 7-0: Wiring EC-Sensor to a BACnet network To wire a laptop to the BACnet network via an EC-Sensor, do the following: Figure 7-: Wiring EC-Sensor to a BACnet Network Bus Topology For information on best practices, specifications, and wiring rules, please refer to the BACnet Network Guide.. Remove the front plate of the EC-. Connect the BACnet cables coming from the previous device and going to the EC-Sensor to the and input terminals on the controller. Maintain consistent wire polarity. If inserting multiple wires in the terminals, ensure to properly twist wires together prior to inserting them in the terminal connectors. Also, connect the shield of the two () cables together while keeping it as short as possible.. Connect the BACnet cables going to the next device and coming from the controller to the and input terminals on the EC- If inserting multiple wires in the terminals, ensure to properly twist wires together prior to inserting them in the terminal connectors. Also, connect the shield of the two () cables to the input terminal on the EC-. Connect the three () wires that terminate with the ⅛" audio cable to the output terminals of the BACnet/IP to MS/TP Adapter.. Insert the ⅛" audio cable into the communications jack of the EC- Toll-free: Tel. International:
6 Hardware Installation Guide - 0DI-HIECSEN-0 EC-Sensor, EC-Sensor-O, EC-Sensor-S, EC-Sensor-SO, EC-Sensor-SOF Copyright Distech Controls Inc. First printed July 00 While all efforts have been made to verify the accuracy of information in this manual, Distech Controls is not responsible for damages or claims arising from the use of this manual. Persons using this manual are assumed to be trained HVAC specialist / installers and are responsible for using the correct wiring procedures and maintaining safe working conditions with fail-safe environments. Distech Controls reserves the right to change, delete or add to the information in this manual at any time without notice. Distech Controls and the Distech Controls logo are trademarks of Distech Controls Inc. Echelon, LON, LonTalk, LONMARK and LONWORKS are registered trademarks of Echelon Corporation registered in the United States and other countries. BACnet is a registered trademark of ASHRAE. *0DI-HIECSEN-0* 0DI-HIECSEN-0 Toll-free: Tel. International:
T7560A,B,C Digital Wall Module
T7560A,B,C Digital Wall Module HONEYWELL EXCEL 5000 OPEN SYSTEM BEFORE INSTALLATION All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams. Digital
More informationTR21, TR22, TR23, and TR24 Wall Modules
TR21, TR22, TR23, and TR24 Wall Modules FEATURES INSTALLATI INSTRUCTIS The TR21, TR22, TR23, and TR24 family of wall modules include: Models with setpoint adjustment. Models with humidity output. Models
More informationElectronic Control Devices The European Product Catalogue 2007
FX14 Field Controller (1/4) FX14 Field Controller The FX14 is an equipment field controller in the Facility Explorer range of products. The controller is designed specifically for commercial Heating, Ventilating,
More informationETC TWO STAGE ELECTRONIC TEMPERATURE CONTROL
RANCO INSTALLATION INSTRUCTIONS ETC TWO STAGE ELECTRONIC TEMPERATURE CONTROL Relay Electrical Ratings PRODUCT DESCRIPTION The Ranco ETC is a microprocessor-based family of electronic temperature controls,
More informationDUAL SENSING DIGITAL THERMOSTAT PRODUCT INSTRUCTIONS. Construction Automotive Industry
DUAL SENSING DIGITAL THERMOSTAT PRODUCT INSTRUCTIONS www.rehau.com Construction Automotive Industry SCOPE This guide gives instruction regarding REHAU Programmable Digital Thermostat installation and operation.
More informationHVAC and Lighting Control Products for Open Building Automation Systems
HVAC and Lighting Control Products for Open Building Automation Systems Distech Controls offers an extensive line of feature-rich and cost effective controllers for building automation, covering HVAC
More informationInstalling the Tracer ZN517 Unitary Controller Ordering number: 4950 0496, 4950 0596
Installing the Tracer ZN517 Unitary Controller Ordering number: 4950 0496, 4950 0596 Product overview The Tracer ZN517 controller is a field-installed, application-specific controller that provides directdigital
More informationHMI display Installation Guide
HMI display Installation Guide Product Description Specifications Important Information o Package Contents o Related Documents o Accessories Cautions and Warnings Mounting and Dimensions o BAC-DIS-ENC
More informationMCR1900 Media Converter 19-Slot Chassis
MCR1900 Media Converter 19-Slot Chassis Installation Guide Part #5500304-11 Copyright Statement This document must not be reproduced in any way whatsoever, either printed or electronically, without the
More informationUniStream CPU-for-Panel
UniStream CPU-for-Panel Installation Guide USC-P-B10 Unitronics UniStream platform comprises control devices that provide robust, flexible solutions for industrial automation. This guide provides basic
More informationDuct Humidity Transmitter
SDC-H Duct Humidity Transmitter Features Replaceable sensor element Humidity measurement for air ducts Minimum and maximum value memory 0 0V, 0 0mA or 0V, 4 0mA measuring signals selectable with jumpers
More informationRack Installation. Unpacking the System. Choosing a Setup Location. General Server Precautions. Barracuda Appliances
This set of instructions applies to racking and rail kit installation for 6XX and above. The Rack Mounting Instructions section below provides information on installing the SC825 chassis into a rack unit
More informationRadiant Temperature Sensor TY7321
AB-5361-U Specifications/Instructions Radiant Temperature TY7321 General TY7321 Radiant Temperature s are designed to measure infrared radiation from perimeter windows and walls and provide a proportional
More informationSerial ATA to Serial ATA
Serial ATA to Serial ATA Model: MRK-300ST-BK Aluminum Mobile Rack 3-1 3-1 Introduction... 3-3 Mobile Rack Features... 3-3 Unpacking Your Mobile Rack... 3-4 IDE Basics... 3-4 3-2 Hardware Installation...
More informationUSER MANUAL WARNING! CONTENTS MODEL 1 SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING. Non-Programmable Single Stage Heat/Cool Thermostat
Builder MODEL 1010 Series Non-Programmable Single Stage Heat/Cool Thermostat USER MANUAL Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single stage
More informationElectronic Control Devices The European Product Catalogue 2007
FX07 Field Controller (1/4) FX07 Field Controller Display Model Dimensions in mm (inches) The FX07 is a terminal unit controller in the Facility Explorer range of products. The controller is designed specifically
More informationMNL-10Rxx Series MNL-15Rxx Series MNL-20Rxx Series
MNL-10Rxx Series MNL-15Rxx Series MNL-20Rxx Series TAC I/A Series MicroNet MN 100, MN 150, and MN 200 Controllers Installation Instructions Application The TAC I/A Series MicroNet MNL-10Rxx, MNL- 15Rxx,
More informationENCL-MZ800-WAL ENCL-MX800-PAN MNL-800-101. TAC I/A Series MicroNet MN 800 Series Controller Installation Instructions. Application.
ENCL-MZ800-WAL ENCL-MX800-PAN MNL-800-101 TAC I/A Series MicroNet MN 800 Series Controller Installation Instructions Application The TAC I/A Series MicroNet 800 Series Controllers are programmable, interoperable,
More informationAutomatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811
Instruction Sheet 1-2003 Automatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811 PURPOSE OF KIT A CCM-T is used to monitor and control an automatic transfer switch. The
More informationTable of Contents. 1 - Specifications...3. 2 - Installation...3. 3 - Wiring...5. 4 - User controls...7
THERMOSTATS Table of Contents Page 1 - Specifications...3 1.1 - Product range...3 ARTTH001 (DSL-610)...3 ARTTH002 (DSL-700)...3 ARTTH003 (DSL-600)...3 1.2 - Technical data...3 1.3 - Power failures...3
More informationWireless Alarm System. Panic Button. User s Manual. Choice ALERT. Control all sensors, accessories and remote transmitters from one location
Wireless Alarm System Panic Button User s Manual Choice ALERT Control all sensors, accessories and remote transmitters from one location Table of Contents Important Safeguards 4 Introduction 5 Activating
More informationTAC I/NETTM MR-VAV-AX. Application Specific MicroRegulator TM
TAC I/NETTM TM TAC s TM has an extensive range ofpre-engineered VAV control sequences, which combined with a fully integrated actuator and airflow transducer, makes it a low Total Installed Cost solution
More informationT0118 T2118 T3118. Instruction Manual
Programmable indoor transmitter of temperature T0118 Programmable indoor transmitter of atmospheric pressure T2118 Programmable indoor transmitter of temperature, relative humidity and other derived humidity
More informationLIEBERT VNSA Installation Sheet
LIEBERT VNSA Installation Sheet Description The Liebert vnsa network switch is designed for connecting multiple Ethernet-ready devices and comes in various models. The unit may have: A Liebert icom display
More informationFX07 Field Controller
Product Bulletin FX07 Field Controller Issue Date March 25, 2008 FX07 Field Controller The FX07 is a high performance field controller designed specifically for commercial Heating, Ventilating, Air Conditioning,
More informationShort Range Wireless Switch System Handheld 8 Installation and Operations Guide
Phone: (866) 701-1146 Fax: (425) 216-7558 www.remotecontroltech.com Short Range Wireless Switch System Handheld 8 Installation and Operations Guide Introduction... 2 Before Installation... 2 Receiver Installation...
More informationInstaller Guide smart connect
Installer Guide smart connect TM 7330 Wireless Remote Humidity Sensor Please read all instructions before proceeding. The wireless remote humidity sensor monitors the humidity passing through the return
More informationINSTALLATION INSTRUCTIONS
LIGHTING CONTROL PANELS 4 AND 8 RELAYS INSTALLATION INSTRUCTIONS INSTALLATION OVERVIEW The installation instructions contained in this document are provided as a guide for proper and reliable installation.
More informationT7079A,B Solid State Remote Temperature Controllers
T7079A,B Solid State Remote Temperature Controllers FEATURES PRODUCT DATA Switch selection of heat or cool mode. Temperature sensing up to 400 feet. Does not require field calibration. 0K NTC temperature
More informationVentostat Wall Mount. Telaire Wall Mount CO 2. , Humidity and Temperature Transmitters. GE Measurement & Control. Features:
GE Measurement & Control Ventostat Wall Mount Telaire Wall Mount, Humidity and Temperature Transmitters Features: Patented, Absorption Infrared Gas sensing engine provides high accuracy in a compact low
More informationInstallation Guide. Wyse D Class 4-GB RAM Upgrade Option Kit. Products: D90D7, D90DW. Issue: 121312 PN: 883884-35L Rev. A
Installation Guide Wyse D Class 4-GB RAM Upgrade Option Kit Products: D90D7, D90DW Issue: 121312 PN: 883884-35L Rev. A Copyright Notices 2012, Wyse Technology Inc. All rights reserved. This manual and
More informationI nstallation. M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications. Tools Needed.
FANs 268.1, 1628.3 Installation Bulletin M100Q Issue Date 1099 M100Q Series Proportional Actuator with R81Q Controller Board for Thermistor Sensor Applications I nstallation Parts Included M110QGA-1 and
More informationAdvantium 2 Plus Alarm
ADI 9510-B Advantium 2 Plus Alarm INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Carefully Read These Controls Corporation of America 1501 Harpers Road Virginia
More informationSMART Board interactive flat panel with appliance Model 8055ie-SMP
Specifications SMART Board interactive flat panel with appliance Model 8055ie-SMP Physical specifications Size 52 3/8" W 32 5/16" H 3 11/16" D (133 cm 82 cm 9.3 cm) (See Physical dimensions on page 7 for
More informationSTAT-RT Series. www.distech-controls.com
Allure Communicating Thermostat RT Series PIR Motion Detector-Ready Rooftop Thermostats Overview Applications Controls rooftop and self-contained units, providing: Single stage and multi stage temperature
More informationREAD THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS MAY VOID YOUR WARRANTY!
READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS MAY VOID YOUR WARRANTY! The main power to any existing system must be disconnected prior to the
More informationDrayton Digistat +2RF/+3RF
/+3RF Programmable Room Thermostat Wireless Model: RF700/22090 Model: RF701/22092 Power Supply: Battery - Thermostat Mains - Digistat SCR Invensys Controls Europe Customer Service Tel: 0845 130 5522 Customer
More informationWIND ALARM. Wind Speed Alarm. Wind Speed. Set Point 2. Set Point 1 NEW BEDFORD, MA 02745 USA
Thank you for purchasing the Maximum wind speed alarm. The Maximum wind speed alarm is a dual set point wind speed indicator with a two digit LED display. It contains a yellow light to display one set
More informationPeriodic Verification System Model 775PVS
Periodic Verification System Model 775PVS Instruction Manual Contents 1 Description... 1 775PVS System... 1 Model 775 Fieldmeter... 2 Model 775C Charger... 2 Model 775P Plate Assembly... 3 2 Operation...
More informationAU-110 racking guide NBXPN: 023
AU-110 racking guide NBXPN: 023 1. Overview NIMBOXX AU-110 Rack Installation This guide provides setup instructions for installing your NIMBOXX AU-110 in a rack. Following these steps in the order given
More informationMIC-BP4 Bi-Phase Converter Card For the MIC400 series camera
MIC-BP4 Bi-Phase Converter Card for the MIC400 PTZ Camera Series Bosch Security Systems EN Installation and Operation Manual BP4 Bi-phase card Installation and Operation Manual AAAEN 2 MIC-BP4 Bi-Phase
More informationAbout the BitStorm 6051 POTS Splitter
BitStorm 6051 Installation Instructions Document Number 6051-A2-GZ40-10 July 2002 About the BitStorm 6051 The BitStorm system enables simultaneous high-speed digital data access and analog voice service
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS VOLT LED Edge-Lit Flat Panel VFP-22 and VFP-24 Series Help Hotline: 1-813-978-3700 Mon-Fri 8am-8pm Sat-Sun 10am - 6pm (EST) Specifications and product details subject to change
More informationY7230A CO 2 Alarm System
Y7230A CO 2 Alarm System FOR CO 2 GAS DETECTION PRODUCT DATA FEATURES APPLICATION Y7230A CO 2 alarm system is used to detect gas leaking from CO 2 beverage dispensing systems and posts an alarm to occupants
More informationWireless Alarm System. Wireless Keypad. User s Manual. Choice ALERT. Control all sensors, accessories and remote transmitters from one location
Wireless Alarm System Wireless Keypad User s Manual 1 2 3 4 Choice ALERT Control all sensors, accessories and remote transmitters from one location Table of Contents Important Safeguards 4 Introduction
More informationMAKING MODERN LIVING POSSIBLE. AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS
MAKING MODERN LIVING POSSIBLE AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS How to Use This Guide Read this Guide completely as you install and start up your new AK-SC 255 controller.
More informationSCREENLOGIC INTERFACE WIRELESS CONNECTION KIT
SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT FOR INTELLITOUCH AND EASYTOUCH CONTROL SYSTEMS INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Technical
More informationOutdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points
Outdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points Features SELV Compliant No Detection Passive Injector Gigabit Compatible Full Protection
More informationHP 16/18-Port Cable Management Kit Installation Guide
HP 16/18-Port Cable Management Kit Installation Guide Abstract This document describes how to attach the HP 16 Port or 18 Port Cable Management Kit to an HP rack. The cable management bracket is designed
More informationPortable Air Conditioner
Portable Air Conditioner Owner's Manual Model:3 in 1 12,000 Btu/h Series 3 Please read this owner s manual carefully before operation and retain it for future reference. CONTENTS 1. SUMMARY...1 2. PORTABLE
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODEL CHCRV-5 For Use with Bard CH Series 3, 4 & 5 Ton 2-Stage Wall Mount Heat Pumps AND W38H, W43H, W49H and W61H Single Stage Wall Mount
More informationRoof Top Air Conditioner INSTALLATION AND OPERATING INSTRUCTIONS
Roof Top Air Conditioner INSTALLATION AND OPERATING INSTRUCTIONS Ducted System RECORD THIS UNIT INFORMATION FOR FUTURE REFERENCE: Model Number: Serial Number: Date Purchased: This manual must be read and
More informationKNX L. Brightness Sensor. Technical specifications and installation instructions Item number 70119
EN KNX L Brightness Sensor Technical specifications and installation instructions Item number 70119 Elsner Elektronik GmbH Control and Automation Engineering Herdweg 7 D 75391 Gechingen Phone +49 (0) 70
More information2013 Wireless Video Intercom INSTALLATION GUIDE
2013 Wireless Video Intercom INSTALLATION GUIDE INDEX System configuration and wiring VL-SWD501 System Component.. 4 VL-SWD501EX wiring schematic diagram VL-SWD501EX wiring type and length... 5.... 6 Door
More informationRoom Controllers. SER8300 Line Voltage Fan Coil Room Controller with SC3000 Relay Pack
Compatible with SmartStruxure solution SmartStruxure Lite solution Room Controllers Line Voltage Fan Coil Room Controller with SC3000 Relay Pack Application specific controller with customizable covers
More informationGEU-0822 8-Port Gigabit Switch
GEU-0822 8-Port Gigabit Switch 1 V1. 1_20150622 1. INTRODUCTION... 3 1.1 Product Briefs... 3 1.2 Product Features... 3 1.3 Hardware Introduction... 4 2. CONNECTING THE SWITCH... 5 2.1 Package Contents...
More informationA99B Series Temperature Sensors
FANs 125, 121, 930, 930.5 Product/Technical Bulletin A99 Issue Date 0615 A99B Series Temperature s The A99B Series Temperature s are passive PTC (Positive Temperature Coefficient) sensors. The A99B sensors
More informationSolid Core and Split Core Adjustable Current Status Switches CSS-O, CSS-C; CSP-O, CSP-C
Solid Core and Split Core Adjustable Current Status Switches CSS-O, CSS-C; CSP-O, CSP-C DESCRIPTION FEATURES PRODUCT DATA Very low operating trip points LED status indication Integral DIN rail mounting
More informationInstallation. Smart-UPS VT and MGE Galaxy 3500. Maintenance Bypass Panel with Power Distribution (wall-mount) 10-30 kva 208 V
Installation Smart-UPS VT and MGE Galaxy 3500 Maintenance Bypass Panel with Power Distribution (wall-mount) 10-30 kva 208 V Contents Safety... 1 SAVE THESE INSTRUCTIONS...............................
More informationWall-Mounting your HP computer. User Guide
Wall-Mounting your HP computer User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should
More informationMoxa EtherDevice Switch
Moxa EtherDevice Switch EDS-205 Hardware Installation Guide Third Edition, June 2008 2008 Moxa Inc., all rights reserved. Reproduction without permission is prohibited. P/N: 1802002050000 Overview The
More informationPS6500 Storage Arrays Rack Mount Instructions
PS6500 Storage Arrays Rack Mount Instructions Part Number: R724M Rev. A01 Copyright 2010 Dell, Inc. All rights reserved. Dell is a trademark of Dell, Inc. EqualLogic is a registered trademark. All trademarks
More informationRI-215A Operator s Manual. Part Number: 71-0045RK Revision 0 Released: 10/3/05
RI-215A Operator s Manual Part Number: 71-0045RK Revision 0 Released: 10/3/05 Warranty RKI Instruments, Inc., warrants gas alarm equipment sold by us to be free from defects in materials and workmanship,
More informationScreenLogic Wireless Connection Kit. Installation Guide. pool/spa control system
pool/spa control system ScreenLogic Wireless Connection Kit Installation Guide P/N 520663 - Rev B 8 Technical Support Contact Technical Support at: Sanford, North Carolina (8 A.M. to 5 P.M.) Phone: (800)
More informationAbout this Manual. Support for Your Product
About this Manual We ve added this manual to the Agilent website in an effort to help you support your product. This manual is the best copy we could find; it may be incomplete or contain dated information.
More information33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application
33.6W Power over Ethernet Waterproof Adapter PoE Plus Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3at Standard -40 to +60 C Temperature Range Diagnostic LEDs Full Protection
More informationSenses SV series industrial monitor user manual
Industrial Monitors Senses SV series Senses SV19 / SV17 User manual (Issue A) Part No: 85090084 Page 1 of 25 Copyright Copyright 2008 Amplicon Liveline Ltd. All rights reserved. This publication, including
More informationSERVICE MANUAL FOR 12 VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOF TOP UNITS ONLY
RV Products Division SERVICE MANUAL FOR 12 VDC WALL THERMOSTAT AIR CONDITIONING SYSTEMS ROOF TOP UNITS ONLY Airxcel, Inc. RV Products Division P.O. Box 4020 Wichita, KS 67204 1976A376 (1-11) TABLE OF CONTENTS
More information5-port / 8-port 10/100BaseTX Industrial Ethernet Switch User Manual
5-port / 8-port 10/100BaseTX Industrial Ethernet Switch User Manual Content Overview... 1 Introduction... 1 Features... 3 Packing List... 4 Safety Precaution... 4 Hardware Description... 5 Front Panel...
More informationE-PDD Duct Smoke Detector Installation Sheet
E-PDD Duct Smoke Installation Sheet Operation The duct smoke detector's primary purpose is to provide early warning of an impending fire and shut down the HVAC unit in order to prevent smoke from circulating
More informationIntel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide
Intel RAID Maintenance Free Backup Unit 4 Quick Installation User's Guide Thank you for buying an Intel RAID Maintenance Free Backup Unit 4. The Intel RAID Maintenance Free Backup Unit 4 supports the Intel
More informationReplacement Instructions. Warning: During this procedure, keep small parts away from children.
apple Power Mac G4 / Macintosh Server G4 ATA Hard Drive Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void
More informationMounting Plate / Screwdriver. Alignment Stickers Screws / Desiccant Bag / Double-sided Tape / Rubber Seal Plug / Rubber Washer
5000020G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny
More informationHP UPS R1500 Generation 3
HP UPS R1500 Generation 3 Installation Instructions Part Number 650952-001 NOTE: The rating label on the device provides the class (A or B) of the equipment. Class B devices have a Federal Communications
More informationFront Panel Board Cable Replacement Instructions
apple Mac Pro Front Panel Board Cable Replacement Instructions First Steps 1 Shut down computer. Note: Follow these instructions carefully. Failure to do so could damage your equipment and void its warranty.
More informationDS 10.210A 07/99 MN MI I/A SERIES MICRONET INTERFACE APPLICATION SPECIFICATION
DS 10.210A 07/99 MN MI WIRING AND COMMISSIONING INFORMATION FOR I/A SERIES MICRONET INTERFACE APPLICATION Order Type: MNN-Ml-100 MicroNet NCP Interface The I/A Series MicroNet Interface (MI) provides network-level
More informationDucoterra Radiant Heating Panel Installation Manual
Ducoterra Radiant Heating Panel Installation Manual 1. Introduction Your new radiant heating panels are designed to heat living and working spaces rapidly and efficiently by radiant heating. Like the sun,
More informationMicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module (MS/TP)
Installation and Maintenance Manual IM 852 Group: Controls Part Number: IM 852 Date: June 2007 Supercedes: New MicroTech II McQuay Maverick II Rooftop Unit Controller BACnet Communication Module (MS/TP)
More informationRMM2 Heat-Tracing Remote Monitoring Module for the Raychem NGC Control System Installation Instructions
Heat-Tracing Remote Monitoring Module for the NGC Control System Installation Instructions Tools Required 3 mm slotted screwdriver 3/8 hex key (for -4X only) Approvals Nonhazardous locations Type NM LISTED
More informationI NTERFACE CABLE ADAPTER MODULE
I NTERFACE CABLE ADAPTER MODULE The Interface Cable Adapter Module (ICAM) has two basic uses. First, it enables you to run shielded cable between the industrial sensor interface module (SIM) and the weather
More informationINSTALLATION INSTRUCTIONS MC95HAE-1 MASTER CONTROLLER
INSTALLATION INSTRUCTIONS MC95HAE-1 MASTER CONTROLLER Bard Manufacturing Company, Inc. Bryan, Ohio 43506 Since 1914...Moving ahead just as planned. Manual : 2100-360B Supersedes: 2100-360A File: Volume
More informationProcessor Cage Fans, Front and Rear Replacement Instructions
apple Mac Pro Processor Cage Fans, Front and Rear Replacement Instructions First Steps 1 Shut down computer. Note: Follow these instructions carefully. Failure to do so could damage your equipment and
More informationDS 1.102 DRTE. AIR ROOM TEMPERATURE SENSOR with fan speed control switches
DS 1.102 02/99 AIR ROOM TEMPERATURE SENSOR with fan speed control switches Specification No. 528-X-XXX* The Active Room Temperature sensor incorporating fan speed control switches is designed to give a
More informationWireless Indoor/ Outdoor Thermometer
Wireless Indoor/ Outdoor Thermometer Owner s Manual Please read before using this equipment. ˆ Contents FCC Information... 3 FCC Declaration of Conformity... 5 Preparation... 5 Installing Batteries...
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet NV24A--RE Communicative globe valve actuator for 2-way and 3-way globe valves Actuating force 1000 N Nominal voltage AC/DC 24 V Control Modulating DC (0)2...10 V Variable Nominal stroke
More informationProduct Catalog BAS-PRC010-E4. Tracker Version 12 Building Automation System. August 2010
Product Catalog Tracker Tracker Version 12 Building Automation System August 2010 BAS-PRC010-E4 Introduction The Tracker Version 12 building automation system (BAS) is a heating, ventilating, and air conditioning
More informationEMBEDDED ACCESS CONTROL Hardware Installation Guide
EMBEDDED ACCESS CONTROL Hardware Installation Guide Lenel goentry Hardware Installation Guide, product version 1.00. This guide is item number DOC- ENHW-ENU, revision 1.003, April 2009 Copyright 2009 Lenel
More informationGlobal Water Instrumentation, Inc.
Global Water Instrumentation, Inc. 11390 Amalgam Way Gold River, CA 95670 T: 800-876-1172 Int l: (916) 638-3429, F: (916) 638-3270 6 Tipping Bucket: RG200 02/05/10 01-343 - 1 - Congratulations on your
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Samba OPLC SM35-J-R20 Installation Guide The Unitronics SM35-J-R20 offers the following onboard I/Os: 12 Digital Inputs, configurable via wiring to include: 1 HSC/Shaft-encoder Input, 2 Analog inputs (only
More informationPower Supply Guide Version 1.0 for D-Show
Power Supply Guide Version 1.0 for D-Show Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support (USA) tel: 650 731 6100 fax: 650 731
More informationOEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE
OEM Manual MODEL 2350 ELECTRONIC DUAL CYLINDER SCALE Scaletron Industries, Ltd. Bedminster Industrial Park 53 Apple Tree Lane P.O. Box 365 Plumsteadville, PA 18949 USA Toll Free: 1-800-257-5911 (USA &
More informationIntesisBox KNX Mitsubishi Heavy Industries AC
IntesisBox KNX Mitsubishi Heavy Industries AC Gateway for integration of Mitsubishi Heavy Indsutries (MHI) Air Conditioners with KNX control systems. 1. Main Features Direct connection to KNX TP-1 (EIB)
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
More informationWIRELESS STATUS MONITOR
INSTALLATION INSTRUCTIONS WIRELESS STATUS MONITOR (WSM or AUWSM) The most current version of this document is available for download at: http://www.ir-swa.com P/N: M053-032-D Schlage 245 W. Roosevelt Road,
More informationOPTICAL HEADEND PLATFORM OTOHP-NMS NETWORK MONITORING MODULE INSTRUCTION MANUAL
OPTICAL HEADEND PLATFORM OTOHP-NMS NETWORK MONITORING MODULE INSTRUCTION MANUAL Phone: (209) 586-1022 (800) 545-1022 Fax: (209) 586-1026 OTOHP-NMS Rev. X1 E-Mail: salessupport@olsontech.com www.olsontech.com
More informationCELO5. User & Installation Manual. www.audac.eu
CELO5 User & Installation Manual www.audac.eu 2 Introduction 5 High-end Slim Ceiling Speaker The CELO5 is the 5 version of AUDAC s CELO High-end Slim ceiling speaker series with an RMS power of 50 Watt
More informationD7050/D7050TH. Installation Instructions. Multiplex Photoelectric Smoke Detectors
D7050/D7050TH EN Installation Instructions Multiplex Photoelectric Smoke Detectors D7050/D7050TH Installation Instructions.0 Description Notices These instructions cover the installation of the D7050/D7050TH
More information3 IN 1 BATHROOM HEATER
3 IN 1 BATHROOM HEATER MODEL NO.: A515 - SH MINI FUNCTION: HEATER, EXHAUST FAN AND LIGHT Dear customers, Thank you for selecting the AUPU 3 in 1 Bathroom Heater. Please read all instructions before commencing
More informationCooktop Low-Profile Ventilation Hoods
INSTALLATION GUIDE Cooktop Low-Profile Ventilation Hoods Contents Wolf Cooktop Low-Profile Ventilation Hoods........ 3 Cooktop Low-Profile Hood Specifications.......... 4 Cooktop Low-Profile Hood Installation............
More information5800 Temperature Sensor Cable Assembly
5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the
More information