2 Contents How to use the pen... 3 Use with Windows... 4 Use with Mac OS Troubleshooting
3 How to use the pen Before using the pen, install the batteries. Pointer Before using the pointer Screw the long rod into the body of the pointer until it is secure. How to use the pointer While pressing the button, when the LED lamp lights, the infrared ray LED at the end of the rod also lights. This is sensed by the infrared ray sensor on the front of the projector, and the location of the tip of the pointer is detected. LED lamp Button Procedures for use: 1) Place the tip of the pointer anywhere on the screen. 2) Pressing the button once has the same function as left-clicking a mouse. Press and hold the button to drag. In pen mode, you can draw lines. Power button Pen Tip with touch sensor How to use the pen While pressing the tip against a hard screen, the tip of the pen and the LED for the internal infrared ray will both light. This is sensed by the infrared ray sensor on the front of the projector, and the location of the tip of the pen is detected. Procedures for use: 1) Place the tip of the pen anywhere on the screen. 2) By pressing the tip against a hard screen, you can drag. In pen mode, you can draw lines. Power button NOTE Since there is a touch sensor inside the tip of the pen, pushing or bending the tip will consume battery power. In order to prevent unnecessary battery consumption when not in use, press the power button to turn the power off. (Press the tip of the pen to confirm that the LED does not light.) 3
4 Use with Windows Interactive functions use the LightPenII software. 1. System requirements In order for the interactive functions to work properly, the computer system must meet the following requirements. System requirements Supported OS Microsoft Windows XP (SP2), Vista, Windows 7 (32bit/64bit) CPU 2.0 GHz or faster Intel Pentium 4 (dedicated GPU is recommended) Memory 512 MB or more Free disk space 80 MB 2. Install the LightPenII software (Windows XP procedures) Step 1: Insert the CD-ROM into the CD-ROM drive. Step 2: Launch the setup file. Step 3: Follow the instructions shown on screen to complete installation of the software. 4
5 3. Setup the interactive functions 3.1 Connect the projector and PC using a USB cable. 3.2 Launch the SPIIdriver software from the start menu or the desktop. Select Next >. Select Next >. 5
6 Select Install. During installation 6
7 Select Finish to complete installation of LightPenII. 3.3 Calibration Step 1: Left-click the SPIIdriver System icon in the taskbar. Step 2: Select Calibration. Step 3: Place the tip of the pointer or pen (select according to screen size) on the + mark and press the button. That + mark changes from green to black, and the next green mark appears in the middle of the top of the screen. Follow the same procedures to turn all 13 + marks black. In order to complete calibration smoothly, make sure that the pointer or pen tip always has a clear line of sight to the sensor beneath the projector lens. The sensor can detect the tip s position well when light from the projector shines on it. 7
8 Hint If the screen and projector positions are fixed, this calibration will not be necessary the next time that you use the same computer and screen resolution with them. 3.4 Set to launch at start up Step 1: Left-click the SPIIdriver System icon in the taskbar. Step 2: Select StartUp so that a check mark appears next to it as shown below. Hint When StartUp is selected, the SPIIdriver System software will automatically be launched the next time that Windows is started up, and the icon will appear in the taskbar at the bottom of the screen and the tool bar will appear at the right side of the screen. To disable the StartUp setting, click StartUp again to remove the checkmark. 3.5 Launch LightPenII Launch the LightPenII software from the start menu or the desktop. 8
9 4. Using the interactive functions 4.1 Functions of the icons in the tool bar Mouse Functions like a PC mouse Red pen Draws red lines Green pen Draws green lines Blue pen Draws blue lines Marker Draws marker lines Shape tool Draws circles, squares, triangles and straight lines Line thickness and color Use to change the pen color and line thickness Eraser Erases parts of drawn lines and shapes Delete Deletes an entire line or shape at once Save file Saves the currently shown screen to the computer Whiteboard mode Changes to the whiteboard mode Last page Returns to the previous page Next page Advances to the next page Editing tool Use to edit a drawn line or picture Quit Quits LightPenII application 9
10 4.2 Other functions (1) Shape tool Click the shape tool icon you want to draw. to open the shape menu as shown below, and select the shape (2) Whiteboard mode Select the whiteboard mode icon to make the background of the PC screen white. The (last page) and (next page) icons are replaced by the (background selection) and (white background) icons. i. Select the background selection icon to open the following window where you can choose the background that you want to use. ii. Select the white background icon to change the background to white. To exit whiteboard mode, select the whiteboard icon again. 10
11 (3) Editing tool Select the editing tool icon to open the editing tool bar as shown below, and select the function that you need to use for editing. Icon Description Select object Rotate object Print Undo Redo 4.3 Mouse mode (immediately after startup) Use the pointer or pen to move the mouse pointer. When using the pen, press the tip of the pen to the screen. When using the pointer, press and hold down the button during use. When in mouse mode, press and hold the pointer button or tip of the pen for about 2 3 seconds to right-click. 4.4 Switching quickly between mouse and pen modes Click the pointer or pen tip above or below the screen to switch between mouse and pen modes. In mouse mode, the icon appears in the taskbar. After switching to the red pen mode, the icon appears. 11
12 4.5 Pen mode Select the pen from the tool bar to use the pen or pointer to draw lines. You can set the line thickness and color. When using as a pen, use it like an ordinary pen, pressing its tip against the screen as you draw. When using as a pointer, press and hold the button as you draw. By selecting the pen icon from the tool bar, you can use the pen or pointer to draw. You can change the line thickness and color from the tool bar. 4.6 Changing the position of the tool bar You can change the tool bar position, as well as set whether or not to show it. Select just outside the left or right screen edge with the light pen or pointer to show or hide the tool bar on that side. 12
13 5. PowerPoint Tool The PowerPoint Tool does not support PowerPoint Set PowerPoint Tool Setting to On. When a PowerPoint file is in Slide Show mode, the PowerPoint Tool bar appears on the right side of the screen. When you quit PowerPoint mode, the PowerPoint Tool automatically disappears. 13
14 5.1 Explanation of PowerPoint Tool bar functions Icon Description Shrink Tool bar Change Tool bar side Mouse Mouse Right Key Red pen Erase Clear all Previous page Next page Select PowerPoint page Exit 14
15 Use with Mac OS Interactive functions use the LightPenII software. 1. System requirements In order for the interactive functions to work properly, the computer system must meet the following requirements. System requirements Supported OS Mac OS X or later (except ) CPU Intel processor Memory 512 MB or more Free disk space 10 MB 2. Install LightPenII software Step 1: Insert the CD-ROM into the CD-ROM drive. Step 2: Copy the LightPenII 2.0 MS folder to the hard disk. Step 3: Eject the CD-ROM from the CD-ROM drive. Step 4: Launch the LightPen2.0 M. CAUTION Do not launch the software directly from the CD-ROM. 3. Setup the interactive functions 3.1 Connect the projector and Mac using the included USB cable 3.2 Double-click the LightPen2.0 M or LightPen2.0 M shortcut icon to launch the program. The icon appears in the menu bar at the top of the screen and the tool bar appears at the right side of the screen. 15
16 3.3 Calibration Step 1: Left-click the LightPenII icon in the menu bar. Step 2: Select Calibration. Step 3: Place the tip of the pointer or pen (select according to screen size) on the + mark and press the button. That + mark changes from green to black, and the next green mark appears in the middle of the top of the screen. Follow the same procedures to turn all 13 + marks black. In order to complete calibration smoothly, make sure that the pointer or pen tip always has a clear line of sight to the sensor beneath the projector lens. When light from the projector shines on the tip, the sensor can detect its position well. Hint If the screen and projector positions are fixed, this calibration will not be necessary the next time that you use the same computer and screen resolution with them. 16
17 3.4 Set to launch at start up Step 1: Left-click the LightPenII icon in the menu bar. Step 2: Select StartUp so that a check mark appears next to it as shown below. Hint When StartUp is selected, the LightPenII software will automatically be launched the next time that Mac OS is started up, and the icon will appear in the menu bar at the top of the screen and the tool bar will appear at the right side of the screen. To disable the StartUp setting, click StartUp again to remove the checkmark. 17
18 4. Using the interactive functions 4.1 Functions of the icons in the tool bar Tool bar position Moves tool bar to right or left side of screen Mouse Enables mouse function Mouse Right Key Enables right-click function Mouse Double Click Enables double-click function Pen thickness Selects pen thickness Pen color Selects pen color Red Pen Draws red lines Green Pen Draws green lines Blue Pen Draws blue lines Black Pen Draws black lines Marker Pen Draws marker lines Eraser Erases parts of drawn lines and shapes Delete Deletes an entire line or shape at once Redraw Use to undo last drawing (or erasing) Save file Saves the currently shown screen to the computer Last page Returns to the previous page Next page Advances to the next page 18
19 4.2 Mouse mode (immediately after startup) Use the pointer or pen to move the mouse pointer. When using the pen, press the tip of the pen to the screen. When using the pointer, press and hold down the button during use. When in mouse mode, press and hold the pointer button or tip of the pen for about 2 3 seconds to right-click. Right-clicking and double-clicking Select the right-click or double-click icon from the tool bar, and move the cursor to a file you want to open and click. This is convenient for opening files. 19
20 4.3 Switching quickly between mouse and pen modes Click the pointer or pen tip above or below the screen to switch between mouse and pen modes. In mouse mode, the icon appears in the menu bar. After switching to the red pen mode, the icon appears. 4.4 Pen mode Select the pen from the tool bar to use the pen or pointer to draw lines. You can set the line thickness and color. When using as a pen, use it like an ordinary pen, pressing its tip against the screen as you draw. When using as a pointer, press and hold the button as you draw. 20
21 Hint You can change the tool bar position, as well as set whether or not to show it. Put the tip of the pen just outside the left or right edge of the screen and press. When using the pointer, press the button when just outside the left or right edge. 5. Disabling interactive functions 5.1 Left-click the LightPenII in the menu bar. 5.2 Select Exit. 5.3 Left-click to quit the software. (You can do this from either the screen or the computer.) 21
22 Troubleshooting Q1: There is a LightPenII cannot be found message. A: Check the following things. (1) Confirm that the USB cable is connected securely and that the USB port is functioning properly. (1-1) If the following warning appears, connect the projector and the computer using the included USB cable, and then restart the program. (1-2) When using Windows, if the LightPenII icon appears like (A) below, the USB connection is not functioning. In this case, confirm that the USB cable is connected securely and that the USB port is functioning properly. The LightPenII is functioning when the LightPenII icon appears like (B). (1-3) When using Mac OS X, if the LightPenII icon appears like (C) below, the USB connection is not functioning. In this case, confirm that the USB cable is connected securely and that the USB port is functioning properly. The LightPenII is functioning when the LightPenII icon appears like (D). NOTE: Some antivirus software disables USB ports. Set such software so that it does not disable USB ports. (2) The USB cable might not be suitable. Use the cable included with the projector. If you need to use a longer cable, please contact the retailer where you purchased this product. (3) The USB port is not working properly. Confirm that the USB port is functioning correctly. If it is not functioning, please consult with an expert. 22
23 NOTE: When using a notebook computer, reduced battery capacity can result in USB ports not working. If this should occur, use AC power. Moreover, some notebook computers are unable to supply the standard current level of 500 ma from USB ports. In addition, some USB converters will not work properly. In such cases, use the included USB cable. Q2: When calibrating the LightPenII, the green + mark will not turn black so I cannot proceed. A: This could be caused by one of the following. (1) Check the following. (1-1) Does the pen or pointer have enough battery charge? (1-2) Is the tip of the pointer or pen in shadow on the screen? If the sensor cannot detect the LED in the tip of the pointer or pen, it will not function. Do not put the pen tip in shadow. The recommended angle is 25º. (2) The surrounding light might be too bright. Move light sources further away from the CMOS sensor and screen. This problem occurs frequently in the following situations. (2-1) Sunlight is entering through a window near the screen (2-2) There is a light source near the sensor or screen (3) When using Windows Vista or Windows 7, the + mark at the bottom left of the screen might be hidden by the start icon. In this case, place the tip where you expect it to be and press the button. Q3: The tip of the pointer and the mouse pointer position are not the same. A: This could be caused by one of the following. (1) Calibration was not conducted accurately. (2) After calibration, the projector or screen was moved. (3) The computer resolution was changed. Recalibrate in any of these cases. 23
24 Q4: The mouse pointer jumps around regardless of the movement of the pointer tip. A: This could be caused by one of the following. (1) There might be interference from a strong light nearby. Block nearby light from reaching the screen. (See Q2 above.) (2) Since remote control use can cause malfunction, do not use one when using the interactive functions. Q5: When the computer is restarted from standby mode, LightPenII does not work. A: When a computer is put into standby mode, its USB ports might be shut down. Quit the LightPenII program once and then restart it. (See Q1 above.) Q6: Why does this message appear? Strong lighting in the environment may cause light pen to stop functioning normally. A: The surrounding light is too bright. Interfering light can appear white as shown below. Move those light sources or the screen, turn the lights off, use curtains or try other means to prevent such interference. 24
25 Notes about the LightPenII software for interactive functions LightPenII software might not function properly with some computer systems. Using RescueLightPen software (use with Windows) On some computers that have free ffdshow software installed, problems might occur with the LightPenII software due to compatibility issues. In this case, run RescueLightPen, and then start LightPenII. Download the latest versions of software from the following URL. Precautions related to the use of batteries with pens and pointers Use 2 AAA alkaline batteries. Change both batteries at the same time. Do not mix and use old and new batteries together. Keep batteries away from water and other liquids. Keep the pen and pointer away from heat and humidity. Do not drop the pen or pointer. If a battery should leak, wipe the leakage away completely and put in new batteries. Installing the wrong type of batteries could cause them to rupture. When discarding batteries, follow the instructions issued by local government authorities and the battery manufacturer. 25
Interactive Functions Manual Optical touch control projector packing list... i Accessories...ii Install in Windows OS... 1 Install in Mac OS... 20 Install in Linux OS... 28 Troubleshooting... 30 Optical
Presentation Draw E User s Guide Be sure to keep all user documentation handy for future reference. The term pointer in this manual refers the YA-P10 interactive pointer. Microsoft, Windows and Windows
SMART BOARD USER GUIDE FOR PC What is it? SMART Board is an interactive whiteboard available in an increasing number of classrooms at the University of Tennessee. While your laptop image is projected on
Smart Board Low Cost Interactive Whiteboard The Bluetooth Digital Pen Pre-paired Bluetooth USB Dongle Quick Installation Guide QUICK SOFTWARE SETUP & DRIVER INSTALLATION ILS Communications Inc. www.penlab.co.kr
Installing and Using the Epson Easy Interactive Tools with a BrightLink Projector These instructions are for both Mac & Windows clients Table of Contents Installing Epson Tools on a Mac Computer... 2 Install
SAS COMPUTER GAME UPDATE GUIDE FOR WINDOWS 8 or 10 & MAC 0S X YOSEMITE or MAC OS X EL CAPITAN Thank you for purchasing one of the Secret Agent Society (SAS) resources. This resource includes the animated
SB101 SMART Board 101 Pieces and Parts SMART Board with cable connected to a laptop or desktop computer LCD projector with cable connected to the computer Computer SMART Board cable (use the appropriate
SMART Board User Guide for PC What is it? The SMART Board is an interactive whiteboard available in an increasing number of classrooms at the University of Tennessee. While your laptop image is projected
LCD MONITOR TOUCH PEN UTILITY OPERATION MANUAL Version 1.0 Applicable models (as of March 2014) PN-L703A/PN-L603A/PN-70TA3/PN-60TA3/PN-ZL01/PN-ZL02 (Available models differ according to region.) Contents
User Guide Copyright 2008 Sanford, L.P. All rights reserved. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into another language without
Smart Sympodium User Guide - PC What is it? The SMART Sympodium is an interactive electronic lectern available in a number of classrooms at the University of Tennessee. The Sympodium console surface contains
EasyMP Network Projection Operation Guide Contents 2 Before Use Functions of EasyMP Network Projection....................... 5 Sharing the Projector....................................................
BrightLink Pro BrightLink Interaction Three interactive modes are available: Whiteboard mode Quick Reference This card will help you get started using your BrightLink Pro interactive projector. Use one
PN-L702B LCD MONITOR TOUCH PANEL DRIVER OPERATION MANUAL Version 2.1 Contents Setting up the PC...3 Installing the touch panel driver...3 Touch Panel Settings...4 How to configure settings...4 Calibration...5
LCD MONITOR TOUCH DISPLAY DRIVER OPERATION MANUAL for Mac Version 1.0 Applicable models PN-K322B/PN-K322BH/LL-S201A Contents Introduction...3 System Requirements...3 Setting up the Computer...4 Installing
LCD MONITOR TOUCH PANEL DRIVER 2 OPERATION MANUAL for Mac Version 1.0 Applicable models PN-L703A/PN-70TA3/PN-L703B/PN-70TB3/PN-L603A/PN-60TA3/PN-L603B/PN-60TB3 Contents Introduction...3 System Requirements...3
Kid-Tough Digital Studio Download PC software to import, organize, view and add special effects to your photos! Go to www.fi sher-price.com/kidtough and follow the on-screen instructions to download and
If a button is stuck down for longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes. Using the remote control under
Introduction Thank you for purchasing this Olympus product. Before you start to use your new Olympus product, please read these instructions carefully to enjoy optimum performance. Note The contents of
Nikon Firmware Update for Coolpix 2500 Version 1.1 Notes: 1. It is most important that you follow the supplied directions; failure to follow all of the steps may result in your camera being disabled. 2.
EasyMP Network Projection Operation Guide Contents 2 Before Use Functions of EasyMP Network Projection....................... 5 Sharing the Projector....................................................
BrightLink Interaction The BrightLink interactive pens turn any wall or table into an interactive area, either with or without a computer. With a computer, you can use Easy Interactive Tools (dual pens).
This Quick User Guide helps you get started with the IRIScan Book Executive 3 scanner. This scanner is supplied with the software applications Readiris Pro 14 and IRIScan Direct (Windows only). Corresponding
User Manual for Mac & Windows Mac to Mac / Mac to Windows / Windows to Windows / Windows/Mac to ipad Windows/Mac to Android TABLE OF CONTENTS INTRODUCTION... 2 FEATUR ES... 2 SYSTEM REQUIREMENTS... 2 REGULATORY
Software User Guide For the safe use of your camera, be sure to read the Safety Precautions thoroughly before use. Types of software installed on your computer varies depending on the method of installation
Yamaha 01V96 Version2 Upgrade Guide This document explains how to upgrade the 01V96 system software to V2.00 or later. Precautions (please be sure to read these precautions) The user assumes full responsibility
Magic Wand Portable Scanner PDS-ST470-VP User Manual Table of Contents 1. Key Features... 3 2. Functional Parts... 3 3. Explanation of the Status Icons... 5 4. Using the Scanner... 5 4.1. Charging up the
USB 2.0 VGA Adapter USER MANUAL CONTENTS INTRODUCTION... 3 FEATURES... 3 SYSTEM REQUIREMENT... 3 PACKAGE CONTENTS... 3 SUPPORTED COMMON DISPLAY RESOLUTION:... 4 DEVICE INSTALLATION ON WINDOWS 2000/XP SYSTEM...
This Quick User Guide helps you get started with the IRIScan Book 3 scanner. This scanner is supplied with the software applications Readiris Pro 12, IRIScan Direct and IRISCompressor. Corresponding Quick
DATA PROJECTOR XJ-A135V/XJ-A145V/XJ-A155V/ XJ-A235V/XJ-A245V/XJ-A255V Data Projector USB Function Guide Be sure to read the precautions in the separate User s Guide (Basic Operations). For details about
E Screen Receiver for fx-cg Series ClassPad 330 PLUS ClassPad II (for Windows, for Macintosh) User s Guide CASIO Worldwide Education Website http://edu.casio.com Manuals are available in multi languages
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Follow these tips
Firmware Update Instruction Manual This manual explains the procedures for downloading the CX2 firmware from the Ricoh website and updating the camera s firmware. Perform the following operations to update
Lenovo Miix 2 8 User Guide Read the safety notices and important tips in the included manuals before using your computer. Notes Before using the product, be sure to read Lenovo Safety and General Information
Florence School District #1 Module 2: SMART Board Basics and Beyond 1 SMART Board Software and Beyond In SMART Notebook software, you can create or open SMART Notebook software (.notebook) files. After
Interactive Whiteboard User Manual Please keep this manual for future reference. This is the general manual for the Interactive Whiteboard and there might be slight differences Copyright 2012 QOMO HiteVision,
now!board User Manual Installation and Operation now!board Vernon Hills, IL US King s Lynn, Norfolk, PE30 4JX, UK www.mynowboard.com 1-800-561-0301 Contents Overview... now!board Equipment... The Camera...4
Interactive Unit User's Guide Important Safety Instructions Make sure you read the Quick Setup Guide and follow the instructions in this document to install the Interactive Unit. Keep the Quick Setup Guide
Table of Contents LEGAL NOTICE... 3 1. INTRODUCTION... 4 1.1 About NovoScreenote Software... 4 1.2 System Requirements... 4 2. INSTALLING NOVOSCREENOTE... 5 2.1 Installing NovoScreenote on your PC (Windows)...
Welcome! Welcome to the GMATPrep application. The GMATPrep test-preparation software was designed by the people who created the GMAT exam, to help you get ready to take the test. It includes practice questions
For safe and correct use, be sure to read the Safety Information in Read This First before using the machine. Operating Instructions TABLE OF CONTENTS Introduction...6 How to Read This Manual...7 Symbols...7
Captureboard C-20 Series PLUS C-20 Software Software Operation Manual We greatly appreciate your purchase of this PLUS Corporation product. In order to take full advantage of the features of the PLUS C-20
EasyMP Multi PC Projection Operation Guide Contents 2 About EasyMP Multi PC Projection Meeting Styles Proposed by EasyMP Multi PC Projection........ 5 Holding Meetings Using Multiple Images................................
This Quick User Guide helps you get started with the IRIScan Book Executive 3 scanner. This scanner is supplied with the software applications Readiris Pro 14 (Windows and Mac ), IRIScan Direct and IRISCompressor
The SMART Board Interactive Whiteboard 1. Press the power button, the indicator ring flashes green to indicate that the projector lamp is starting up. The What would you like to do? menu will be displayed.
IWB Setup Software/EyeRIS NEC edition OPERATION MANUAL This manual describes installation and operation procedures of the driver / the calibration software Supported model NP03Wi NP04Wi UM352W (for the
V2.0 Congratulations on your purchase of the AORUS Notebook! This Manual will help you to get started with setting up your notebook. For more detailed information, please visit our website at http://www.aorus.com.
Instruction Manual Document Camera Controller Software Image Mate Please read this manual carefully before using Image Mate. Contents Introduction... 4 Welcome!...4 Notes...4 Before Use... 5 System Requirements...5
DUKANE AV PRODUCTS INTERACTIVE WHITEBOARD Touch operation Model LB78T User Guide IWB Model LB78T Information in this Guide may change due to product improvements. To obtain the latest manuals, literature,
Important Please read this Installation Guide carefully to familiarize yourself with safe and effective usage. The latest software and Installation Guide are available for download from our site: http://www.eizo.com
California State University, Fullerton Campus Information Technology Division Documentation and Training Services Handout Epson Brightlink Interactive Board and Pen Training Downloading Brightlink Drivers
3M Occupational Health and Environmental Safety 3M E-A-Rfit Validation System Version 4.2 Software Installation Guide (Upgrade) 1 P age Contents Important Information Read First... 3 Software Download...
User Guide HUAWEI UML397 Welcome to HUAWEI 1 Huawei UML397 4G LTE Wireless Modem User Manual CHAPTER 1 BEFORE USING YOUR UML397 WIRELESS MODEM ABOUT THIS USER MANUAL...4 WHAT S INSIDE THE PRODUCT PACKAGE...4
Magic Control Technology Corporation Android Mirror KM-C6105 Table of Contents Features... 3 Specifications... 3 Getting Started... 4 Windows 7 / XP - First Time Installation... 4 Windows 7 Start the Andriod
P3PC-4162-03EN Getting Started Thank you for purchasing ScanSnap ix500 (hereinafter referred to as "the ScanSnap"). This manual describes the preparation required for use of the ScanSnap. Follow the preparation
Hi-Speed USB Flash Disk UFD Utility User s Manual For AP v18.104.22.168 Release For Windows 98/ME/2000/XP Version 1.1B (08/27/2004) Contents Contents...1 Introduction...1 Features & Specifications...2 System
KIDILOOK TM 2008 91-002348-000 INTRODUCTION Thank you for purchasing the VTech Kidilook! Kidilook is a digital photo frame that allows kids to view and share their favorite pictures. With Kidilook, you
Promethean Board To start: - Plug in the USB cable to the Promethean Board. - Turn on the projector. - Mac: Double-click Macintosh HD. Go to Applications > Promethean > Activsoftware Inspire > Inspire.
Remote Control Operation The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen, or the front or back of the projector.
OFFICE KEYBOARD (MT1210 & MT1405) OFFICE FEATURES Thank you for purchasing OFFICE KEYBOARD. This User s manual contains all information that helps you to operate your keyboard. Please keep the software
Parallels Software International, Inc. Parallels Desktop for Mac Quick Start Guide 3.0 (c) 2005-2007 Copyright 2006-2007 by Parallels Software International, Inc. All rights reserved. Parallels and Parallels
Using Easy Interactive Tools Starting Easy Interactive Tools To start Easy Interactive Tools on your computer, do one of the following: Windows: Double-click the Easy Interactive Tools icon on your desktop
Installation Manual for Multi-purpose Ecological Risk Assessment and Management Tool (AIST-MeRAM) For Windows 8 December 25, 2014 National Institute of Advanced Industrial Science and Technology (AIST)
USER GUIDE USB 2.0 TO DVI-I ADAPTER Model: 30535 1 TABLE OF CONTENTS Introduction...2 Features...3 System Requirements...4 Package Contents...5 Device Overview...6 Device Driver Installation on Windows
Stereo Turntable System Application Hi-Res Audio Recorder About Hi-Res Audio Recorder What Is Hi-Res Audio Recorder?  Supported Stereo Turntable System  Audio File Formats Supported for Recording
EasySuite User Guide V1.0 1 Launch EasySuite...3 Stop the EasySuite:...4 System Requirements...5 EasyCopy...6 Function Description...7 File Transfer...9 EasyMover...12 Function Descriptions of EasyMover...12
AirLiner Slate Page 1 About An AirLiner wireless slate allows you to interact wirelessly with our computer. It can be used with a Smart board, but one is not required. Multiple slate users can write at