Instruction Bulletin. Hospital Isolated Power Systems Digital Clock Timer and Surgical Chronometer Class 4890 INTRODUCTION RECEIVING AND INSPECTION
|
|
- Doris Harrell
- 7 years ago
- Views:
Transcription
1 Instruction Bulletin Bulletin No. 0--0A January 00 Raleigh, NC, USA Replaces 0--0, 0-0-0, 0-0-0, and 0--0 Hospital Isolated Power Systems Digital Clock Timer and Surgical Chronometer Class Digital Clock Timer MCT-B Surgical Chronometer MCT-B Figure : Clock Timer MCT-B and Surgical Chronometer MCT-B INTRODUCTION Clock Timer Accessories Chronometer Accessories RECEIVING AND INSPECTION This bulletin provides installation and operation information for Square D digital clock timers (MCT-B), surgical chronometers (MCT-), and related accessories. Accessories for the clock include the following items: Remote control panel (MCT-CT) for controlling the clock timer and setting the time display.the panel requires a cable harness assembly to connect to the panel and clock timer. Battery pack (MCT-BP) can be purchased separately or is supplied with the remote control panel for clock timer operation during a power interruption. Trim plate (MCTS-) and back box (00BB) are options that allow the clock timer to be remotely controlled when the clock is mounted high on a wall. The surgical chronometer must be purchased with the remote control panel (MCT-RC). This control panel includes the battery pack and cable harness assembly. A backbox (00BB) for the chronometer and a backbox (00BB) remote control panel may be purchased for mounting to the wall. Before using or storing the clock timer or chronometer, inspect it for any possible shipping damage. Upon receipt, remove the unit from its package and inspect it for damage or signs of rough handling. If damage is apparent, notify the shipping agent and your Square D sales representative. If the damages necessitate returning the unit to the factory for service, obtain a return material authorization (RMA) from the nearest Square D sales office or factory first.
2 Digital Clock Timer and Surgical Chronometer Bulletin No. 0--0A Mounting January 00 MOUNTING Clock Timer Mount the clock timer from the rear of a 0.0 inch (. ) panel with four #- x / inch screws (not supplied) Clock Display Timer Display Fuse Press / A Hr 0:0 0:0 Count Reset Hold 0 Hours 0 Min...0. Trim Plate and Backbox Accessories for Clock Timer Figure : Clock Timer (MCT-B) Dimensions.00 0 Backbox (00BB).00.0 Trim Stainless Steel (MCTS-).0 Digital Clock.0. 0:0 0:0 Count Reset Hold Hours.00 0 Fuse Minutes Digital Elapsed Timer (MCT-B) Remote Control Panel Accessory for Clock Timer Figure : Trim Plate (MCTS-) and Backbox (00BB) Dimensions. NOTE: Backbox (-Gang) not supplied. Recoended conduit size between control and clock is /" Stainless Steel Trim COUNT HOLD.0 RESET HRS MIN BATTERY TEST. Figure : Remote Control Panel (MCT-CT) Dimensions
3 Bulletin No. 0--0A January 00 Digital Clock Timer and Surgical Chronometer Mounting Surgical Chronometer Mount the surgical chronometer from the front of the panel with four #- screws (not supplied). Backbox (00BB).00 0 Clock Black Anodized Aluminum Cover.00 Timers : 0: : : Surgical Time Heparin Time Pump Time Card Holder To Describe Timer Function (Typical) Figure : Surgical Chronometer (MCT-B) and Backbox (00BB) Dimensions Remote Control Panel for Surgical Chronometer.0..0 HOURS MIN BATTERY TEST HOLD COUNT..0 0 HOLD COUNT HOLD COUNT 00-0 Figure : Remote Control Panel (MCT-RC) and Backbox (00BB) Dimensions
4 Digital Clock Timer and Surgical Chronometer Bulletin No. 0--0A Wiring January 00 WIRING WARNING ELECTRIC SHOCK, BURN, OR EXPLOSION Hazardous potentials are present on the power leads (black and white). For this reason it is recoended that this device be installed by a qualified electrician. Failure to follow this instruction can result in death or serious injury. Clock Timer The clock timer is equipped with a 0-terminal, printed circuit card connector that mates with a cable harness assembly, part number 0--0 (supplied). The cable harness assembly includes a mating connector (Molex #). All connections to the clock timer for power, remote control switches, indicators, and battery packs are made through the supplied cable harness assembly. The input voltage is specified on the rear label. Connect the input voltage to the black and white leads. The clock s normal operation is in the -hour mode from a 0 Hz source. For 0 Hz operation, cut and tape the ends of the white with red tracer jumper wire on the connector. For -hour mode operation, cut and tape the ends of the white with green tracer jumper wire on the connector. One fuse, which is accessible from the front, provides overcurrent protection. The fuse is a Littlefuse Type AG, / A, 0 V. NOTES:.Jumper wire P- to P- remains connected for 0 Hz operation; disconnect for 0 Hz operation..jumper wire from P- to P- remains connected for -hour operation; disconnect for -hour operation..for external remote start of timer, connect P- and P- to the normally open (N.O.) and coon (COM) contacts of the remote switch. Clock Timer P White/Red White/Green Orange Violet White/Gray White White/ or Tan White/Black 0 Black Count 0 Volts Incoming Power To Remotely Start Timer Figure : Wiring for Clock Timer (MCTB) with No Remote Control Accessory
5 Bulletin No. 0--0A January 00 Digital Clock Timer and Surgical Chronometer Wiring Remote Control Panel for Clock Timer The remote control panel MCT-CT is for use with the clock timer and enables the clock timer to be controlled from a remote location.the panel contains the COUNT RESET, HOLD, HRS, and MIN switches, which are also located on the clock itself. The remote control panel also contains two rechargeable batteries ( V Nickel Metal Hydride) to permit the clock to count internally (no display) during a power failure, and a battery test switch. A charged battery causes the battery test light to glow when the battery test switch is pressed. The batteries are recharged by the clock timer. The accuracy of the clock timer when powered by the batteries is within one second per minute on fullycharged batteries. All switches are disabled during battery operation to prevent accidental resetting. NOTE: Fully-charged batteries will be completely discharged if power is lost for more than one hour. Two days are required for the batteries to become fully recharged after they are completely discharged. NOTES:. Jumper wire P- to P- remains connected for 0 Hz operation; disconnect for 0 Hz operation.. Jumper wire from P- to P- remains connected for -hour operation; disconnect for -hour operation.. For external remote start of timer, connect P- and P- to the normally open (N.O.) and coon (COM) contacts of the remote switch. Clock Timer P 0 White/Red White/Green Red Green Brown Blue Orange Violet White/Gray Hold LED Minutes Hours Hold Count Battery ( ) Volts 0 Volts White White/ or Tan Battery Charge White/Black Black Incoming Power MCT-CT Remote Control To Remotely Start Timer Figure : Clock Wiring with Remote Control (MCT-CT)
6 Digital Clock Timer and Surgical Chronometer Bulletin No. 0--0A Wiring January 00 Battery Pack The battery pack MCT-BP is for use with clock timer and is used in conjunction with the memory feature of the control panel MCT-CT. The battery pack prevents time information from being lost during short power interruptions. The battery pack contains the two rechargeable batteries, which allows the clock to count internally (no display) when power is lost. CAUTION LOSS OF TIME INFORMATION Batteries will discharge if power is removed. Test batteries prior to use. Replace batteries if discharged. Failure to follow this instruction can result in loss of information. NOTES:.Jumper wire P- to P- remains connected for 0 Hz operation; disconnect for 0 Hz operation..jumper wire from P- to P- remains connected for -hour operation; disconnect for -hour operation..for external remote start of timer, connect P- and P- to the normally open (N.O.) and coon (COM) contacts of the remote switch..to connect external rechargeable batteries, wire nut P- and P- to the positive lead of the battery (as shown in Figure). P- is connected to the negative lead of the battery. Clock Timer P 0 White/Red White/Green Orange Violet White/Gray White White/ or Tan White/Black Black Rechargeable Batteries ( V Nickel Metal Hydride) Qty. = Incoming Power Count Battery ( ) Volts 0 Volts Battery Charge Pigtail Blue Pigtail To Remotely Start Timer Figure : Clock Wiring with Battery Pack Accessory (MCT-BP) Surgical Chronometer The surgical chronometer is equipped with a -terminal printed-circuit card connector that mates with a cable harness assembly and remote control panel MCT-RC. The cable harness assembly includes the Molex # mating connector. All connections for power are made to the three-point terminal block located on the bottom of the chronometer. The input voltage is specified on the rear label Connect the input voltage to the terminal labeled BLK & WHT. Connect the ground to GND. The connections for the remote control switches, indicators, and batteries are made through the supplied cable harness assembly. The chronometer s normal operation is in the -hour mode from a 0 Hz source. For 0 Hz operation, cut and tape the ends of the gray jumper wire and violet jumper wire on the connector. For -hour mode operation, cut and tape the ends of the white with gray tracer jumper wire on the connector. One fuse, which is accessible from the front, provides overcurrent protection. The fuse is a Littlefuse Type AG, / A, 0 V. The cable harness assembly is used to connect the surgical chronometer with its remote control and is supplied with the remote control. The recoended conduit size for wiring between the surgical chronometer and the remote control is 0. in ( ). Figure illustrates these connections.
7 Bulletin No. 0--0A January 00 Digital Clock Timer and Surgical Chronometer Wiring NOTES:.Jumper wire P- to P- and from P- to P- remains connected for 0 Hz operation; disconnect for 0 Hz operation..jumper wire from P- to P- remains connected for -hour clock operation; disconnect for -hour operation. Surgical Chronometer MCT-B 0 Black White Red White/Gray Green Orange Violet White/Blue/White Blue White/Black Gray Red/Black Green/Black Orange/Black Blue/Black Black/White Red/White Green/White Blue/White V Battery Charge Hold LED # Hold LED # Hold LED # Battery 0 V Hold Display # Count Display # Hold Display # Count Display # Hold Display # Count Display # Hours Min MCT-RC Figure : Wiring Connections Between Chronometer and Remote Control Panel Remote Control Panel for the Surgical Chronometer Figure : Panel with harness POWER UP 00-0 The MCT-RC control unit is for use only with surgical chronometer. It contains the COUNT RESET, HOLD, HRS, and MIN switches for operating the chronometer. The unit also contains four rechargeable batteries ( V Nickel Metal Hydride) to permit the clock to count internally (no display) during a power failure or a battery test switch. A charged battery causes the battery test light to glow when the battery test switch is pressed. The batteries are recharged by the chronometer. The accuracy of the chronometer when powered by the batteries is within one second per minute on fully-charged batteries. All switches are disabled during battery operation to prevent accidental resetting. NOTE: Fully-charged batteries will be completely discharged if power is lost for more than one half-hour. Two days are required for the batteries to become fully recharged after they are completely discharged. If fully-charged batteries are connected to an unenergized chronometer, the controls may not operate the chronometer when power is applied. Should this occur, discharge the batteries completely before applying power to the chronometer. The clock timer has two displays, one for elapsed time and one for real time. The controls are built into the clock timer. The COUNT RESET, HOLD switches are on the front panel. The HRS and MIN set switches are accessible through holes in the front panel. When power is first applied, the top display reads 00:00 for a -hour mode clock and :00 for a -hour mode. The -hour mode has a leading zero for 0- hours. The -hour mode does not. The lower display shows the elapsed time in all zeroes (00:00). The HOLD LED is illuminated. NOTE: In the event of a power interruption (when the battery pack is not used), the clock timer displays the 00:00 for -hour mode or :00 for -hour mode. Clock Display Timer Display Reset the Count Button Hold the Count Button Hours Set Switch Minute Set Switch Figure : Clock Timer Displays
8 Surgical Clock Timer and Chronometer Bulletin No. 0--0A Instruction Bulletin January 00 OPERATION Setting the Clock Measuring Elapsed Time To set the minutes of the clock, press the MIN switch with an appropriate tool such as a pencil or paper clip. Press the MIN switch to advance the clock one minute; holding it closed advances the clock rapidly. Release the switch when the proper time is displayed. To set hours, use the same method, but press the HRS switch. When the clock is set, the colon between hours and minutes pulses every second and the time is displayed. Each time you press the MIN switch, the seconds count resets to zero to provide accurate start times. Simultaneously pressing the MIN and HRS switches resets the clock to midnight (that is, 00:00). Press the COUNT RESET switch to activate the elapsed time mode in the timer display. To hold the display at zero, press both the COUNT RESET and HOLD switches simultaneously. To reset to zero and restart the timing, press the COUNT RESET switch. At anytime during the count, press the HOLD switch to stop the count. The HOLD button LED lights when on hold. To resume counting, press the HOLD switch again. The elapsed time display format is initially in minutes and seconds. When the elapsed time exceeds one hour, the display format changes to hours and minutes up to hours, minutes. An asterisk behind the HR on the display window indicates the change in format to the hour and minutes display. Also, the colon is illuminated continuously in the elapsed time mode. Square D Company P.O. Box Raleigh, NC -, USA --Square D (---) Square D and are registered trademarks of Square D Company. Electrical equipment should be serviced only by qualified electrical maintenance personnel. No responsibility is assumed by Square D for any consequences arising out of the use of this material.
HONDA ACCORD 1985-2005
HONDA ACCORD 1985-2005 VEHICLE WIRING Copyright 2002-2004 Triple S Customs WIRING INFORMATION: 1985 Honda Accord WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WHITE or WHITE/BLACK Ignition Harness STARTER
More informationISUZU RODEO 1992-2003
ISUZU RODEO 1992-2003 VEHICLE WIRING Copyright 2002-2004 Triple S Customs WIRING INFORMATION: 1992 Isuzu Rodeo 12V CONSTANT WIRE BLACK Ignition Harness STARTER WIRE WHITE/BLUE OR BLACK/WHITE Ignition Harness
More informationPart Number: 250-1859
General Applicability 2010 Honda Insight 07- Kia Optima / Forte / Rondo/ 10- Sedona / 12 Soul 10- Hyundai Tucson / Elantra Touring ETC 2012 Accent / Elantra/ Genesis Recommended Tools Safety Tools Gloves,
More informationMazda CX7 2007-09 99-7508
INSTALLATION INSTRUCTIONS FOR PART 99-7508 APPLICATIONS Mazda CX7 2007-09 99-7508 KIT FEATURES DIN Radio Provision with Pocket ISO Mount Radio Provision with Pocket Double DIN Mount Radio Provision Stacked
More informationINSTALLATION & SERVICE MANUAL. Display Panel
INSTALLATION & SERVICE MANUAL Display Panel The PowerLine EMS TM is a specialized power distribution and energy management system intended to be used in recreational vehicles. The Control Module is housed
More informationIntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide
IntelliBrite Controller (For IntelliBrite Pool, Spa and Landscape Lighting Fixtures) Installation and User s Guide *619751* P/N 619751 - Rev C IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS
More informationHP UPS R1500 Generation 3
HP UPS R1500 Generation 3 Installation Instructions Part Number 650952-001 NOTE: The rating label on the device provides the class (A or B) of the equipment. Class B devices have a Federal Communications
More informationBattery Charger For Nickel Cadmium and Nickel-Metal Hydride Rechargeable Batteries Model PSN Series
Battery Charger For Nickel Cadmium and Nickel-Metal Hydride Rechargeable Batteries Model PSN Series Operating Instructions WARNING CONCERNING THE REMOVAL OF COVER: CAUTION: TO PREVENT THE RISK OF ELECTRIC
More informationPart Name/Description Part Number Quantity. Power Cable 4000950-5 1
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Power Cable 4000950-5 1 Raven Harness Adapter Kit 4100525 1 Installation Instructions
More informationCHAPTER 5 PARTS. This chapter describes assemblies / subassemblies / parts considered replaceable at on-site field installation.
CHAPTER 5 PARTS PARTS BY PICTORIAL This chapter describes assemblies / subassemblies / parts considered replaceable at on-site field installation. NOTE: The following is a breakdown description of the
More informationwww.sebury.com.cn Digital Keypad Use s Manual
K3 K4 www.sebury.com.cn Digital Keypad Use s Manual Contents Introduction Introduction Specifications Intramural Interface Circuit 3 Mounting 3 Wiring 5 Power UP 7 Engineer Programming Mode 7 The K3/K4
More informationWIRING HARNESS FOR AS635P4. BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness
WIRING HARNESS FOR AS635P4 ANTENNA NOT USED 5 PIN WHITE PLUG 2 PIN WHITE PLUG GREEN - PARKING BRAKE INPUT (-) BLUE - NOT USED 3 PIN BLUE PLUG RED, BLUE, BLACK, WHITE - Plug in dual stage sensor harness
More informationInstallation and Operation Guide for PD4000 Series Power Control Center
Extended warranties are available for purchase at www.progressivedyn.com Installation and Operation Guide for PD4000 Series Power Control Center Member Thank you for selecting Progressive Dynamics as your
More informationLESTRONIC DV AUTOMATIC 12 OR 24 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/24EL40-10ET
LESTRONIC DV AUTOMATIC 12 OR 2 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/2EL0-10ET PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment,
More informationINSTALLATION GUIDE OWNER S GUIDE
INSTALLATION GUIDE OWNER S GUIDE SECURITY SYSTEM PRO-SERIES 5002 CONTENTS System Features... 1-2 System Components... 2 Technical Assistance... 2 Before You Begin... 2 Precautions... 2-3 Making Connections...
More informationINSTALLATION GUIDE. Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930
INSTALLATION GUIDE Card Reader & Controller with KIM Swipe Reader for Solitaire 850 / 950 / 850L Learnlok PK2930 Card Reader and Controller Model 3.5 with KIM Swipe Reader Table of Contents 1. Features..................................
More informationISL-540 TBTS SERIES D EMERGENCY LIGHTING EQUIPMENT
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationGenerator Transfer Switch Model # HTS15-AUTO
Generator Transfer Switch Model # HTS15-AUTO Congratulations on your purchase of our Single Circuit Generator Transfer Switch, We hope this meets and exceeds your expectations. If at anytime you have any
More information12 Volt 30 Amp Digital Solar Charge Controller
12 Volt 30 Amp Digital Solar Charge Controller User s Manual WARNING Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationAdvantium 2 Plus Alarm
ADI 9510-B Advantium 2 Plus Alarm INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Carefully Read These Controls Corporation of America 1501 Harpers Road Virginia
More informationINSTALLATION INSTRUCTIONS
LIGHTING CONTROL PANELS 4 AND 8 RELAYS INSTALLATION INSTRUCTIONS INSTALLATION OVERVIEW The installation instructions contained in this document are provided as a guide for proper and reliable installation.
More information1R / 4-BUTTON SERIES
Button 1 1R / 4-BUTTON SERIES VEHICLE SECURITY SYSTEM Standard Features: Two 4-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren Dual stage impact detector Remote
More information1978-83 Malibu 1978-87 Monte Carlo 1978-87 El Camino
Important facts about this kit. 1. The dash panel used in this picture is used by permission of Covan's Classic. 2. This kit requires some modification to your original under dash wiring harness. It is
More informationFused Spur Time Switch
Fused Spur Time Switch Model No. FST24 24 Hour Timer Model No. FST77 7 Day Timer Installation & Operating Instructions 1. General Information Illuminated screen Sets programmes Sets time and date Reset
More informationSingle Station Remote Alarm
ADI 5106G Certified ISO 9001:2000 Single Station Remote Alarm 529 5106-01-120 529 5106-01-220 INSTALLATION AND OPERATING INSTRUCTIONS Carefully Read These Instructions Before Operating Controls Corporation
More informationKEY TELEPHONE SYSTEMS RESERVE POWER 47C POWER UNIT
BELL SYSTEM PRACTICES AT&TCo Standard SECTION 518-010-107 Issue 1, June 1972 KEY TELEPHONE SYSTEMS RESERVE POWER 47C POWER UNIT 1. GENERAL 1.01 The 47C power unit (Fig. 1) provides emergency power to maintain
More informationRain+Birdt. Simple To Set Timer (SST) Setup & Operation Instructions. English. 1-800- RAIN BIRD (800-724-6247) or visit www.rainbird.
Rain+Birdt Simple To Set r (SST) Setup & Operation Instructions English Installation...2 Tools and Supplies Needed...2 Step 1. Mount r...2 Step 2. Connect Power...2 Indoor r...2 Outdoor r...2 Step 3. Connect
More informationMaster Time Clock MTC-200 MTC-400 MTC-600. Users Manual
Master Time Clock MTC-200 MTC-400 MTC-600 Users Manual Toll Free (888)713-0373 Phone (972)987-4408 FAX (877)720-9291 www.midwest-time.com sales@midwest-time.com TABLE OF CONTENTS TOPIC PAGE GENERAL DESCRIPTION
More informationXSVI-9004-NAV Audi CAN Interface 2002-2013
INSTALLATION INSTRUCTIONS FOR PART XSVI-9004-NAV REV. 9/17/2014 INSTXSVI-9004-NAV AUDI Applications below use LD-AX-XSVI-AU1: A3* 2006-2013 A4/RS 4/S4 with NAV 2005-2008 A4/RS 4/S4 2007-2008 A4/RS 4/S4*
More informationBATTERY BOX INSTALLATION WARNING WARNING CAUTION ATTENTION AVERTISSEMENT ADVERTENCIA PRECAUCIÓN SOLBBOX12V CARTON INVENTORY COMPLETED OVERVIEW
WARNING CARTON INVENTORY CAUTION with: Charger, Cable 15', Fuses (2), Battery Strap and Strain Relief (2) Model SOLBBOX 12V Battery Not Included AVERTISSEMENT ATTENTION DC Power Adapter 12Vdc to 32Vdc
More informationMobile Data Power Model: MDP-25
Mobile Data Power Model: MDP-25 Topic Section Features... 2 Operational Features Summary... 2 Back-up Battery Power Internal Charger Voltage Spike Protection RF Noise Filtering Warning of Imminent Loss
More informationCooktop Low-Profile Ventilation Hoods
INSTALLATION GUIDE Cooktop Low-Profile Ventilation Hoods Contents Wolf Cooktop Low-Profile Ventilation Hoods........ 3 Cooktop Low-Profile Hood Specifications.......... 4 Cooktop Low-Profile Hood Installation............
More informationPRO PLM Installation Instructions
PRO PLM Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationCMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM
INTRODUCTION CMD-8000 rev. A COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM Thank you for purchasing the CMD-8000 Commander from Dakota Digital. This, along with many other products that Dakota Digital has
More informationFG MOISTURE MONITOR Installation & Operation Manual
FG MOISTURE MONITOR Installation & Operation Manual Issue 3.0 7/20/10 1 Contents SERVICE AND TECHNICAL SUPPORT... 2 INSTALLATION:... 3 MOISTURE SENSOR INSTALLATION:... 3 SENSOR CONNECTOR:... 5 MONITOR
More informationTable of Contents. General Operation 2. Air Blast Cleaning System 3. Setup 4. Changing Ticket Bags 5. Loading Printer Paper 6. Tower Light Status 7
Table of Contents General Operation Air Blast Cleaning System Setup Changing Ticket Bags Loading Printer Paper Tower Light Status Ticket Taker General - Ticket Taker Overview - Ticket Taker Operation Clearing
More informationDRM75A 230V 20/100A DIN rail single phase two wire energy meter
DRM75A 230V 20/100A DIN rail single phase two wire energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Description 1.7 Dimensions 1.8 Installation
More informationWATER LEAK DETECTION SYSTEM WLDS-10 INSTALLATION & COMMISSIONING
WATER LEAK DETECTION SYSTEM WLDS-10 INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (water meter with pulse output proportional to flow rate)
More informationInstallation and Operation Guide for PD4100 Series Power Control Centers
Installation and Operation Guide for PD4100 Series Power Control Centers Extended warranties are available for purchase at www.progressivedyn.com Member Thank you for selecting Progressive Dynamics as
More informationwith MERCURY FREE 1 HP Relays ! WARNING Before using this product read and understand instructions.
B Installation & Maintenance Instructions MM-414 Series 150E and 157E Low Water Cut-Off/Pump Controllers For Steam Boilers and Other Level Control Applications A Typical Applications: Primary or secondary
More informationHG600/HG800. Hydro-Power Unit. Installation and Operation Guide
HG600/HG800 Hydro-Power Unit Installation and Operation Guide Copyright 04 HydroSpin, All rights reserved. The data contained in this document is proprietary to HydroSpin. It is disclosed to the receiving
More informatione-ask electronic Access Security Keyless-entry
e-ask electronic Access Security Keyless-entry e-fob Keyless-entry entry System Full-Function Function Installation Manual FCC ID: TV2EFOB1 (UM20 ~ 22793-02) Table of Contents Introduction... 1 e-fob Operation
More informationDIGITAL ALARM II FOR HOSPITALS AND LABORATORIES INSTALLATION AND OPERATING INSTRUCTIONS 52 635.0
Form No. 74-00-4001 S168-195-001 Revision E DIGITAL ALARM II FOR HOSPITALS AND LABORATORIES INSTALLATION AND OPERATING INSTRUCTIONS 52 635.0 INTRODUCTION Allied Healthcare Products, Inc. s Digital Alarm
More informationREMOTE TRANSMITTER LAYOUT
Full Featured Keyless Entry System with Optional Starter Defeat and Passive Immobilize Feature SYSTEM MANUA STANDARD FEATURES Some of the system s standard features include: Two 4-button remote transmitters
More informationInstallation and Operation Guide PD4600 Series Converter Replacement
Installation and Operation Guide PD4600 Series Converter Replacement Extended warranties are available for purchase at www.progressivedyn.com Member Thank you for selecting Progressive Dynamics as your
More informationTSn SERIES Surge Protective Device
Page: 1 of 8 TSn SERIES Surge Protective Installation & Operation Manual 3621 Saunders Avenue www.systems.us Ph 804.355.1100 Richmond, VA 23227 4354 Sales@Systems.us Fax 804.355.8900 Page: 2 of 8 Quick
More informationINSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200
INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200 FUSION CULTURE TABLE OF CONTENTS There s no point doing something if no one notices. We ve always believed the way to make things happen is by getting
More informationPATENTED: www.voxxintl.com/company/patents
Model PRO9776C Installation Manual Vehicle Security System Table Of Contents: with Remote Start Before You Begin Page 2 Wire Harnesses Quick View Page 3-4 Installation of the Major Components Page 5 Wiring
More information2010-13 Field Commander Wiring Manual
2010-13 Field Commander Wiring Manual Section 1 Pages 2-4 BASIC / ENHANCED SERVICE: Pivot wiring NOT using start, theft monitoring, or direction control Section 2 Pages 5-9 PRO SERVICE: Pivot wiring using
More informationDisabled Toilet Alarm. Contractor Pack. Installation & Operating Instructions
Disabled Toilet Alarm Installation & Operating Contractor Pack Installation & Operating Instructions 1 Overview The Channel Safety Systems Disabled Toilet alarm contractor Packs are an efficient way of
More informationCoolWave r 2 Phase Control Board and Cable Replacement Kits
Instruction Sheet P/N 1102452A CoolWave r 2 Phase Control Board and Cable Replacement Kits Two kits are available to replace the CoolWave 2 phase control board: S S Phase Control Board and Cable Kit (required
More informationPART 8: FIELD WIRING. n WARNING NOTICE. Boiler Manual
PART 8: FIELD WIRING A. INSTALLATION MUST COMPLY WITH: 1. National Electrical Code and any other national, state, provincial or local codes or regulations. 2. In Canada, CSA C22.1 Canadian Electrical Code
More informationPOWER LOCK KIT GENERAL INSTALLATION -J04427 REV. 2007-12-04. Kit Number. Models. Additional Parts Required. Kit Contents
-J0 REV. 00--0 POWER LOCK KIT GENERAL Kit Number -0, 0-0 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English
More informationSecurity and Remote Start Installation Guide for models: CA 6150 CA 6550
PROFESSIONAL SERIES Security and Remote Start Installation Guide for models: CA 6150 CA 6550 2009 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 4 Wire Connection
More informationFZ400 1997-1998 WIRING DIAGRAM (JAPANESE MARKET FAZER 400) 5
FZ400 1997-1998 WIRING DIAGRAM (JAPANESE MARKET FAZER 400) 5 1 2 4 7 6 11 12 13 13 12 13 3 13 8 9 56 14 59 52 54 15 48 55 34 22 16 51 50 60 47 46 36 35 23 17 49 24 25 18 44 37 38 39 40 58 33 26 27 28 29
More informationWIRELESS STATUS MONITOR
INSTALLATION INSTRUCTIONS WIRELESS STATUS MONITOR (WSM or AUWSM) The most current version of this document is available for download at: http://www.ir-swa.com P/N: M053-032-D Schlage 245 W. Roosevelt Road,
More informationIMPACT ALARM SYSTEM FOR HOSPITALS AND LABORATORIES INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION
Form No. 74-00-4001 S168-527-001 Rev. B IMPACT ALARM SYSTEM FOR HOSPITALS AND LABORATORIES INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION Allied Healthcare Products, Inc. s IMPACT alarms are designed
More informationK9 Heat Alarm Owners Manual HA-1520
K9 Heat Alarm Owners Manual HA-1520 Your K9 Heat Alarm is a state of the art product designed and developed by ACEK9.COM a division of Radiotronics, Inc. It is a unique blend of positive features taken
More informationInstruction Manual. 2in1 LAN Tester & Multimeter. Model: LA-1011
Instruction Manual 2in1 LAN Tester & Multimeter Model: LA-1011 1 Contents Introduction... Features... Safety Precautions.. Meter Description... Electrical Specification... Operation.. AutoRanging Multimeter.
More informationCR9971 2 Band Auto Set Dual Alarm Clock Radio ROBERTS. Sound for Generations. Please read this manual before use
ROBERTS Sound for Generations CR9971 2 Band Auto Set Dual Alarm Clock Radio Please read this manual before use Contents Contents... 1 Controls...2-5 Switching on... 6 Setting the time manually... 6 Setting
More informationPATENTED: www.voxxintl.com/company/patents
Model APS-997C Installation Manual 2 Way LCD Vehicle Security and Table Of Contents: Remote Start System Before You Begin Page 2 Wire Harnesses Quick View Page 3 and 4 Installation Of The Major Components
More information535T Window Automation System
535T Window Automation System Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained
More informationBattery Chargers. Revised 8/00 Form Number 56041170 FORM NO. 56041170 / BATTERY CHARGER SERVICE MANUAL / PARTS LIST - 45
Battery Chargers SERVICE MANUAL / PARTS LIST AUTOMATIC Advance MODELS 0980, 098, 797, 8809, 90, 880, 880, 099, 08,, 09788, 098, 7, 097, 70, 790, 889 Lester MODELS 007,, 8, 8, 89, 80, 9, 00, 00, 008 MANUAL
More informationInstallation Instructions
H5HK Series Installation Instructions 3 Phase Electric Heater Kits 7.5 and 0 TON Package A/C Systems Description Installation of 08/40V and 480V H5HK 3 Phase Heater Kits in 7.5 and 0 TON Packaged Air Conditioners.
More informationP150SC15. Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System. 2015 Stillwater Designs P150SC15-A2-20150813
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
More informationIntroduction. Safety Guidelines. Part Numbers. Operation and Maintenance Manual. Operation and Maintenance Manual
Operation and Maintenance Manual Introduction Read all instructions thoroughly. Installation of the OilTector must comply with all Federal, State and Local Codes, Regulations and Practices. The OilTector
More informationFIREDEX 2200. Conventional Fire Panels
68 Flexible, high specification system Choice of 1, 2, 4 or 8 zones Simple one-shot auto-reset user test facility Approved to EN54 Maintenance free poly switch circuit protection, with auto reset Class
More informationCUSTOM AUXILIARY FORWARD LIGHTING KIT
-J0 REV. 0--0 CUSTOM AUXILIARY FORWARD LIGHTING KIT GENERAL Kit Number -0, 0000 Models This Custom Auxiliary Lighting Kit adds lamps and turn signals to 00 and later FLHX model motorcycles. Additional
More informationMulti Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter
MODEL PRO-9744 INSTALLATION MANUAL Multi Function, User Configurable Remote Vehicle Security System with 4 Button Replaceable Membrane Remote Transmitter This System Allows The Transmitter Buttons To Be
More informationManual for Fire Suppression & Methane Detection System
Manual for Fire Suppression & Methane Detection System Fogmaker North America Post address: 150 Gordon Dr Exton, PA 19341 Delivery address: 150 Gordon Dr Exton, PA 19341 Tel: 610-265-3610 Fax: 610-265-8327
More informationMazda CX7 2010-up 99-7520B
INSTALLATION INSTRUCTIONS FOR PART 99-7520B APPLICATIONS Mazda CX7 2010-up 99-7520B KIT FEATURES DIN radio provision with pocket ISO radio provision with pocket Double DIN radio provision Painted matte
More informationOperating Instructions
D-TEK Vehicle Loop Detector Operating Instructions This product is an accessory or part of a system. Always read and follow the manufacturer s instructions for the equipment you are connecting this product
More informationCMD-10k COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM
CMD-10k COMMANDER SERIES REMOTE CONTROL ENTRY SYSTEM INTRODUCTION Thank you for purchasing the CMD-10k Commander from Dakota Digital. This, along with many other products that Dakota Digital has to offer,
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationUser Manual for CH-PFC76810
AA Portable Power Corp www.batteryspace.com, Email: Sales@batteryspace.com User Manual for CH-PFC76810 1. Overview The CH-PFC76810 charger is suitable for charging lithium ion battery packs such as those
More informationCo-location Interconnect Power Panel (CIPP) Installation Guide
Co-location Interconnect Power Panel (CIPP) Installation Guide Document INS-97xxxxxxx This guide covers the following part numbers- Trimm 97xxxxxxx Series Table of Contents Section 1 - General Information...
More informationMS4000/MS4000U Mini-Siren
MAN MS4000 INSTALL REV: 1/26/01 255331B INSTALLATION AND OPERATING INSTRUCTIONS MS4000/MS4000U Mini-Siren i Section Title Page I General Description...... 1 II Specifications... 2 III Safety Message To
More informationTHERMONET UNDERFLOOR HEATING STANDARD THERMOSTAT KIT STOCK CODE 5260
THERMONET UNDERFLOOR HEATING STANDARD THERMOSTAT KIT STOCK CODE 5260 STANDARD THERMOSTAT KIT 1.0 KIT CONTENTS Parts included: 1 x Thermostat 1 x Wall plate 2 x Mounting box screws 1 x Floor temperature
More informationDTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual
DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8
More informationChevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G
INSTALLATION INSTRUCTIONS FOR PART 99-3307G Chevy Equinox 2010-2015 / GMC Terrain 2010-2014 (with monochrome display) 99-3307G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision
More informationMAKING MODERN LIVING POSSIBLE. AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS
MAKING MODERN LIVING POSSIBLE AK-SC255 On-Site Installation Guide DANFOSS ELECTRONIC CONTROLS & SENSORS How to Use This Guide Read this Guide completely as you install and start up your new AK-SC 255 controller.
More informationAGS. Owner's Manual. Xantrex Automatic Generator Start Control System
AGS Owner's Manual Xantrex Automatic Generator Start Control System TABLE OF CONTENTS INTRODUCTION...3 Main Features...3 Safety Summary...3 THINGS YOU SHOULD KNOW...4 THEORY OF OPERATION...5 System...5
More informationPOWER TRIM 5 F AUTO TRIM AND AUTO TRIM
POWER TRIM 5 F 22217 AUTO TRIM AND AUTO TRIM Table of Contents Page Auto Trim System........................ 5F-1 Description........................... 5F-1 Auto Trim Operation...................... 5F-2
More informationHow To Power A Power Control On An Ip40 (Ipl) With A Power Supply (Iplug) With An Ip20 Controller (Iphones) With Power Control (Power Control) With No Antenna) With The Ip20 (Power)
MODEL NUMBER: ISC910-1-0-GB-XX ISC911-5-0-GB-XX IXP20 CONTROLLER SPECIFICATIONS Working Environment Plastic Housing... Power ImproX IXP20 Controller INSTALLATION MANUAL Designed to work in an indoor (dry)
More informationPeriodic Verification System Model 775PVS
Periodic Verification System Model 775PVS Instruction Manual Contents 1 Description... 1 775PVS System... 1 Model 775 Fieldmeter... 2 Model 775C Charger... 2 Model 775P Plate Assembly... 3 2 Operation...
More informationHM-W536 Install Guide
HM-W536 Install Guide 9/13/2013 IMPORTANT SAFETY INSTRUCTIONS Warning - When using electrical devices, basic safety precautions should be followed to reduce the risk of fire, electrical shock or injury.
More informationTOYOTA Tundra 2007 - BACK-UP CAMERA SYSTEM Preparation
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
More informationid led 4" square housing FL44
id led 4" square housing FL44 LUMINAIRE MUST BE INSTALLED PRIOR TO DRYWALL CEILING. ALL GRID LUMINAIRES MUST BE SECURED TO STRUCTURE ABOVE. non-emergency optional - bar hangers key sold separately power
More informationLIEBERT VNSA Installation Sheet
LIEBERT VNSA Installation Sheet Description The Liebert vnsa network switch is designed for connecting multiple Ethernet-ready devices and comes in various models. The unit may have: A Liebert icom display
More informationADM1TE 5/30A DIN rail single phase two wire energy meter
ADMTE 5/30A DIN rail single phase two wire energy meter. Safety instruction.2 Foreword.3 Performance criteria.4 Specifications.5 Basic errors.6 Description.7 Dimensions.8 Installation.9 Operating.0 Troubleshooting.
More informationColor Splash LED Light Fixture Installation and Operation Guide
Color Splash LED Light Fixture Installation and Operation Guide Technical Support Phone: 800.735.4553 ext. 242 For more information about this or other J&J Electronics lighting products, please visit www.jandjpoolspa.com
More informationINSTALLATION GUIDE. www.security.soundstream.com FCC ID NOTICE
AL.1 AUTO SECURITY SYSTEM INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device
More informationModel 1756 Test Lead Kit
Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY http://www.keithley.com Model 1756 Test Lead Kit Gerneral Purpose Test Lead Information Description These test leads allow you
More information2003/2004/2005 TOYOTA COROLLA
2003/2004/2005 TOYOTA COROLLA KEYLESS ENTRY UPGRADE SECURITY SYSTEM INSTALLATION INSTRUCTIONS KIT NO. 00016-30120 SPECIAL NOTE: Installation Sequences After TMS and Safety mandated preparatory steps have
More informationDC Series Digital Conversion Alarm Operator s Manual
DC Series Digital Conversion Alarm Operator s Manual Ver. 2012 - Rev. 1004 Class 1 Inc. design manufacture installation service world class innovation Call us for your next project. Area Alarm Conversion
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26327 2004 S2000 Issue Date OCT 2004 PARTS LIST Security System: P/N 08E51-S84-100 Attachment Kit: P/N 08E55-S2A-101 2 Remote controls
More informationAMERBRITE UNDERWATER WHITE LED POOL LAMP
AMERBRITE UNDERWATER WHITE LED POOL LAMP FOR USE ONLY WITH PENTAIR AMERLITE LUMINAIRE INSTALLATION AND USER S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
More informationCONTROL PANEL INSTALLATION INSTRUCTIONS. Single Phase Simplex Page 2-7. 3-Phase Simplex Page 8-13
CONTROL PANEL INSTALLATION INSTRUCTIONS Single Phase Simplex Page 2-7 3-Phase Simplex Page 8-13 Single Phase Simplex SXL21=3, SXL24=3, SXH21=3, and SXH24=3 Manufactured by SJE-Rhombus Installation Instructions
More informationApplied Electronics. Commercial Dimming System UPDATE NOTICE
REV. A Applied Electronics Commercial Dimming System UPDATE NOTICE This notice is to inform the end user of an additional feature added to this DP12/2400 dimming unit. This unit has been outfitted with
More informationModel: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features
Model: LCDM40 4.0 LCD Rear Vision Mirror Monitor Installation Manual Features Mirror with built in 4.0 LCD Monitor Low Profile, Slim Design High Resolution TFT LCD Built in Speaker Two video inputs Fully
More information