mbe2 Accordion/bandoneon MIDI encoder with Air-pressure control * user s guide *
|
|
- Vernon Hill
- 7 years ago
- Views:
Transcription
1 mbe2 JDP 2007 Gadgets Boutique Inc. 1 mbe2 Accordion/bandoneon encoder with Air-pressure control * user s guide * 1. Purpose mbe2 is a small electronic unit, designed to be incorporated in accordion-like instruments (accordion, concertina, bandoneon etc.) in order to make them capable to control synthesizers. mbe2 has two 8x8 scanmatrices, each scanning up to 64 key contacts, analog input for connecting potentiometer and on-board air-pressure transducer. The parameter controlled by Air-pressure as well as parameters controlled by potentiometer are user-programmable by means of free software utility. The event per key contact is user-programmable for each of pressure/bellows directions. The factory pre-programmed events are shown in Table 1. The programming utility SxBlast is free downloadable from our site. The unit can be powered from battery as well as from power supply adapter. 2. Wiring diagram The wiring diagrams of typical mbe2 based applications are shown in Appendices A,B and C. The mbe2 scanmatrix headers are compatible with sm8x8 and keymux64 units. For battery powered application we recommend either using of sm8x8 or direct key contacts wiring. When using keymux64 for interfacing keys, the wiring is minimal compared to other cases, but the application should be powered from external adapter as the current is three times higher in such case. Direct wiring is recommended for applications with limited space where no room for two sm8x8 is available, but requires much more wiring and diode per key. 3. Settings The events for each of mbe2 controls are user-programmable by means of free-downloadable software utility called SxBlast: - For air-pressure control: response curve, message; - For potentiometer control: message; - For each key contact on both sides: On/Off message for positive air pressure (bellows closing), On/Off message for negative air pressure (bellows opening). Once changed, the parameters are memorized in non-volatile memory and used until next change. Table 1. Programmable parameters (factory pre-programmed values) mbe2 control side channe Note message l Key 1 Right Note 36 1 Key 2 Right Note 37 1 Key 3 Right Note 38 1 Key 4 Right Note 39 1 Key 5 Right Note 40 1 Key 6 Right Note 41 1 Key 7 Right Note 42 1 Key 8 Right Note 43 1 Key 9 Right Note 44 1 Key 10 Right Note 45 1 Key 11 Right Note 46 1 On/Off messages may be different for both bellows directions
2 mbe2 JDP 2007 Gadgets Boutique Inc. 2 Key 12 Right Note 47 1 Key 13 Right Note 48 1 Key 14 Right Note 49 1 Key 15 Right Note 50 1 Key 16 Right Note 51 1 Key 17 Right Note 52 1 Key 18 Right Note 53 1 Key 19 Right Note 54 1 Key 20 Right Note 55 1 Key 21 Right Note 56 1 Key 22 Right Note 57 1 Key 23 Right Note 58 1 Key 24 Right Note 59 1 Key 25 Right Note 60 1 Key 26 Right Note 61 1 Key 27 Right Note 62 1 Key 28 Right Note 63 1 Key 29 Right Note 64 1 Key 30 Right Note 65 1 Key 31 Right Note 66 1 Key 32 Right Note 67 1 Key 33 Right Note 68 1 Key 34 Right Note 69 1 Key 35 Right Note 70 1 Key 36 Right Note 71 1 Key 37 Right Note 72 1 Key 38 Right Note 73 1 Key 39 Right Note 74 1 Key 40 Right Note 75 1 Key 41 Right Note 76 1 Key 42 Right Note 77 1 Key 43 Right Note 78 1 Key 44 Right Note 79 1 Key 45 Right Note 80 1 Key 46 Right Note 81 1 Key 47 Right Note 82 1 Key 48 Right Note 83 1 Key 49 Right Note 84 1 Key 50 Right Note 85 1 Key 51 Right Note 86 1 Key 52 Right Note 87 1 Key 53 Right Note 88 1 Key 54 Right Note 89 1 Key 55 Right Note 90 1 Key 56 Right Note 91 1 Key 57 Right Note 92 1 Key 58 Right Note 93 1 Key 59 Right Note 94 1 Key 60 Right Note 95 1 Key 61 Right Note 96 1 Key 62 Right Note 97 1 Key 63 Right Note 98 1 Key 64 Right Note 99 1 Key 1 Left Note 36 2 Key 2 Left Note 37 2 Key 3 Left Note 38 2 Key 4 Left Note 39 2 Key 5 Left Note 40 2 Key 6 Left Note 41 2 Key 7 Left Note 42 2 On/Off messages may be different for both bellows directions
3 mbe2 JDP 2007 Gadgets Boutique Inc. 3 Key 8 Left Note 43 2 Key 9 Left Note 44 2 Key 10 Left Note 45 2 Key 11 Left Note 46 2 Key 12 Left Note 47 2 Key 13 Left Note 48 2 Key 14 Left Note 49 2 Key 15 Left Note 50 2 Key 16 Left Note 51 2 Key 17 Left Note 52 2 Key 18 Left Note 53 2 Key 19 Left Note 54 2 Key 20 Left Note 55 2 Key 21 Left Note 56 2 Key 22 Left Note 57 2 Key 23 Left Note 58 2 Key 24 Left Note 59 2 Key 25 Left Note 60 2 Key 26 Left Note 61 2 Key 27 Left Note 62 2 Key 28 Left Note 63 2 Key 29 Left Note 64 2 Key 30 Left Note 65 2 Key 31 Left Note 66 2 Key 32 Left Note 67 2 Key 33 Left Note 68 2 Key 34 Left Note 69 2 Key 35 Left Note 70 2 Key 36 Left Note 71 2 Key 37 Left Note 72 2 Key 38 Left Note 73 2 Key 39 Left Note 74 2 Key 40 Left Note 75 2 Key 41 Left Note 76 2 Key 42 Left Note 77 2 Key 43 Left Note 78 2 Key 44 Left Note 79 2 Key 45 Left Note 80 2 Key 46 Left Note 81 2 Key 47 Left Note 82 2 Key 48 Left Note 83 2 Key 49 Left Note 84 2 Key 50 Left Note 85 2 Key 51 Left Note 86 2 Key 52 Left Note 87 2 Key 53 Left Note 88 2 Key 54 Left Note 89 2 Key 55 Left Note 90 2 Key 56 Left Note 91 2 Key 57 Left Note 92 2 Key 58 Left Note 93 2 Key 59 Left Note 94 2 Key 60 Left Note 95 2 Key 61 Left Note 96 2 Key 62 Left Note 97 2 Key 63 Left Note 98 2 Key 64 Left Note 99 2 Potentiometer - CC b 1 Expression Air-pressure sensor - CC 7 1 Volume
4 mbe2 JDP 2007 Gadgets Boutique Inc. 4 Air-pressure response curve - Linear - Can be Linear, Log, Exp, S-type Besides the programmed parameter, air-pressure sensor controls notes (re-)triggering. When certain key is held down and the bellows direction changes, the note of this key is being re-triggered. If the same note is programmed for this key per direction, the same note will be re-triggered as this happens in accordion. If different notes are programmed for this key per direction, then the proper note will be triggered upon bellows change. This behaviour is specific for bandoneon as well as some types of concertinas. The channel is programmable for each message so that user can set both sides of instrument to transmit on separate channels or set them to transmit the left side to transmit same note ranges on different MIID channels as well as different note ranges on the same channel. The key contacts on both sides are expected to be normally open. The potentiometer is expected to be 10 kohm, linear. Non-linear potentiometers of 2-20 kohm could be used either. Programming using SxBlast requires using PC-compatible computer, running SxBlast software. Following steps should be performed for this: - run SxBlast software (free downloadable from our site) and select the output port of your sound card; - connect mbe2 input to PC s sound card output using either cable or -PC adapter where necessary; - power up the mbe2 unit; - select desired event per key, potentiometer and airpressure sensor and send it clicking on SendSysEx button. Note that only one control/key can be programmed at a time. Separate programming per control makes programming process slower but allows maximal flexibility; - repeat previous step as many times as many controls you need to program; - disconnect mbe2 unit from PC and use it. Whatever is programmed in it, will be kept in mbe2 internal non-volatile memory till next change. Programming using sequencer or another third-party sequencing software using SysEx messages is also possible. The format of SysEx messages is shown in Appendix D.
5 mbe2 JDP 2007 Gadgets Boutique Inc Technical parameters. The most important technical parameters of mbe2 are listed in Table 2. Table 2. Technical parameters Parameter Value Unit Comment Power supply voltage Power supply current Max. number of scanned contacts 9-12 AC/DC 20 ma 2x64+1 Battery or AC/DC Adaptor - Normally open type Scanrate 250 S -1 being scanned 250 times Each key contact is per second messages for key contacts messages for potentiometer messages for potentiometer note range NoteOn/ NoteOff CC/Pitc h Wheel CC/Pitc h Wheel full - Velocity full - User-programmable Note and Channel User-programmable Channel User-programmable Channel and Response curve Constant velocity per key as programmed by user channels As programmed by user Size 9 x 6.5 cm Approx. 3.5 x 2.6 Weight 48 g Approx. 1.7 oz
6 mbe2 JDP 2007 Gadgets Boutique Inc. 6 Appendix A. mbe2 wiring diagram (when bundled with two keymux64 key multiplexor boards)
7 mbe2 JDP 2007 Gadgets Boutique Inc. 7 Appendix B. mbe2 wiring diagram (when bundled with two sm8x8 spread boards)
8 mbe2 JDP 2007 Gadgets Boutique Inc. 8 Appendix C. mbe2 wiring diagram (direct key contact wiring, requires diode per key contact)
9 mbe2 JDP 2007 Gadgets Boutique Inc. 9 Appendix D. mbe2 programming by SysEx messages SysEx for programming Key events: 20 bytes F0 - start SysEx 00 - first ID 21 - sec. ID (MGB) 7F - thd. ID (MGB) 07 - Device ID (MBE2 = 07) 00 - Device sub-id (Message ID = 00: Key events programming) ee - Key number (0..63-right part, left part) d0 - PushOn event, Status byte (bit#7 must be forced to 0!) d1 - PushOn event, Data1 byte d2 - PushOn event, Data2 byte d3 - PushOff event Status byte (bit#7 must be forced to 0!) d4 - PushOff event Data1 byte d5 - PushOff event Data2 byte d6 - PullOn event, Status byte (bit#7 must be forced to 0!) d7 - PullOn event, Data1 byte d8 - PullOn event Data2 byte d9 - PullOff event Status byte (bit#7 must be forced to 0!) d10 - PullOff event Data1 byte d11 - PullOff event Data2 byte F7 - SysEx end SysEx for programming Settings: 20 bytes F0 - start SysEx 00 - first ID 21 - sec. ID (MGB) 7F - thd. ID (MGB) 07 - Device ID (MBE2 = 07) 01 - Device sub-id (Message ID = 01: Air/Pot events programming) ee - unused (always 127) d0 - Air event, Status byte (bit#7 must be forced to 0!) d1 - Air event, Data1 byte d2 - unused (always 127) d3 - Pot event Status byte (bit#7 must be forced to 0!) d4 - Pot event Data1 byte d5 - unused (always 127) d6 - Pressure response curve No (0-3) d7 - unused (always 127) d8 - unused (always 127) d9 - unused (always 127) d10 - unused (always 127) d11 - unused (always 127) F7 - SysEx end
Keystation Pro 88 Advanced Guide. Contents: 1 Getting Started. 2 Terminology. 3 Performance Operations of the Keystation Pro 88
Keystation Pro 88 Advanced Guide Contents: 1 Getting Started 2 Terminology 3 Performance Operations of the Keystation Pro 88 Sending Program Changes During Performance Sending Bank Changes During Performance
More informationMIDECO 64-outputs MIDI note decoder USER MANUAL. Roman Sowa 2012
MIDECO 64-outputs MIDI note decoder USER MANUAL Roman Sowa 2012 www.midi-hardware.com 1.Overview Thank you for choosing MIDECO as your new MIDI-to-digital converter. This short manual will guide you through
More informationTransmitter Interface Program
Transmitter Interface Program Operational Manual Version 3.0.4 1 Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters. The following
More informationUser's Guide. Integrating Sound Level Datalogger. Model 407780. Introduction
User's Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech 407780 Product Page Integrating Sound Level Datalogger
More informationMIDImplant micro MIDI-2-CV device version 3.8
MIDImplant micro MIDI-2-CV device version 3.8 USER MANUAL Roman Sowa 2015 www.midimplant.com 1. Overview Thank you for choosing MIDImplant as your new MIDI2CV converter. This short manual will guide you
More informationMini Effect Gizmo. User s Manual. RJM Music Technology, Inc.
Mini Effect Gizmo User s Manual RJM Music Technology, Inc. Mini Effect Gizmo User s Manual Version 1.3 September 26, 2013 RJM Music Technology, Inc. 2525 Pioneer Ave #1 Vista, CA 92081 E-mail: support@rjmmusic.com
More informationSMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]
SMS Alarm Messenger SMSPro_Setup Revision 090210 [Version 2.2] ~ 1 ~ Contents 1. How to setup SMS Alarm Messenger?... 3 2. Install the SMSPro_Setup software... 5 3. Connection Type... 6 4. Connection Port
More informationEvolution USB Keyboards. 249/361 USB MIDI Controller Keyboard
Evolution USB Keyboards 249/361 USB MIDI Controller Keyboard 225C/249C/361C USB MIDI Controller Keyboard with additional programmable rotary controllers WWW.EVOLUTION.CO.UK EVOLUTION 249/361/225C/249C/361C
More informationTechnical data. General specifications. Indicators/operating means. Electrical specifications Operating voltage U B Power consumption P 0 Interface
Release date: 06-0- 09: Date of issue: 06-0- 009_eng.xml Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service
More informationUSER GUIDE. Publication AP7080. Allen & Heath 1 XONE:1D User Guide
USER GUIDE Publication AP7080 Allen & Heath 1 XONE:1D User Guide Limited One Year Warranty This product is warranted to be free from defects in materials or workmanship for period of one year from the
More informationTemperature & Humidity SMS Alert Controller
Temperature & Humidity Alert Controller METERS 3 simple steps starting the unit: Insert the SIM card Plug in the sensors connectors Connect the AC power cord. Specifications: AC 90~260V Auto Select Internal
More informationAutomation System TROVIS 6400 TROVIS 6493 Compact Controller
Automation System TROVIS 6400 TROVIS 6493 Compact Controller For panel mounting (front frame 48 x 96 mm/1.89 x 3.78 inch) Application Digital controller to automate industrial and process plants for general
More informationTechnical data. General specifications. Indicators/operating means. 30 Hz Multiplex operation 30 Hz / n, n = number of sensors, n 5
Model Number Single head system Features Parameterization interface for the application-specific adjustment of the sensor setting via the service program ULTRA 000 programmable switch outputs Hysteresis
More informationSMS GSM Alarm Messenger
SMS GSM Alarm Messenger Data Logging Alarm Input Relay Output Voice Temperature Humidity Analog Input Capture and Send Data via SMS Report triggered alarm via SMS Output triggered via SMS Auto pick up
More informationCommunications Protocol for Akai APC40 Controller
Communications Protocol for Akai APC40 Controller Table of Contents Introduction... 3 Scope... 3 Glossary... 3 General Format of MIDI System Exclusive message... 3 Communications from PC Host to device
More informationUMI3 Parametric USB MIDI Foot Controller. User s Manual
UMI3 Parametric USB MIDI Foot Controller User s Manual Table of Contents Table of Contents...2 Document revisions...3 Introduction...3 1. Hardware...4 1.1. USB Connection...4 1.2. Connecting an expression
More informationKTA-223 Arduino Compatible Relay Controller
8 Relay Outputs 5A 250VAC 4 Opto-Isolated Inputs 5-30VDC 3 Analog Inputs (10 bit) Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs, Jumper Selectable 5A Relay Switching Power Indicator
More informationAppendix C: Keyboard Scan Codes
Thi d t t d ith F M k 4 0 2 Appendix C: Keyboard Scan Codes Table 90: PC Keyboard Scan Codes (in hex) Key Down Up Key Down Up Key Down Up Key Down Up Esc 1 81 [ { 1A 9A, < 33 B3 center 4C CC 1! 2 82 ]
More informationUser Manual Software for DSL Digital Speed Switch
User Manual Software for DSL Digital Speed Switch Software version from 1.0.1 Baumer Hübner GmbH Max-Dohrn-Str. 2+4 D-10589 Berlin Phone +49 (0)30 690 03-0 Fax +49 (0)30 690 03-104 info@baumerhuebner.com
More information2.0 Command and Data Handling Subsystem
2.0 Command and Data Handling Subsystem The Command and Data Handling Subsystem is the brain of the whole autonomous CubeSat. The C&DH system consists of an Onboard Computer, OBC, which controls the operation
More informationÂØÒňΠMusic Workstation July 9, 1997
XP-50 ÂØÒňΠMusic Workstation July 9, 1997 Supplemental Notes XP-50 Frequently Asked Questions This document is a compilation of questions and answers commonly asked of the Roland Technical Support department.
More informationMiniBrute Connection software editor 1.0.3
USER'S MANUAL MiniBrute Connection software editor 1.0.3 1 st edition: June 2012 Information contained in this manual is subject to change without notice and does not represent a commitment on behalf of
More informationNortechCommander Software Operating Manual MAN-00004 R6
NortechCommander Software Operating Manual MAN-00004 R6 If the equipment described herein bears the symbol, the said equipment complies with the applicable European Union Directive and Standards mentioned
More informationROCK BAND 3 WIRELESS KEYBOARD:
Music Systems, Inc. ROCK BAND 3 WIRELESS KEYBOARD: MIDI User Guide HMXHW1023 REVISION: 01 Date: 07/16/10 Introduction... 3 What is MIDI?... 3 Features... 3 Getting Started... 4 Control Surface Functions
More informationDeviceNet Bus Software Help for Programming an Allen Bradley Control System
FBP FieldBusPlug V7 DeviceNet Bus Software Help for Programming an Allen Bradley Control System DeviceNet Software Help for Programming an Allen Bradley Control System Contents Page General Purpose...
More informationwww.burntec.com User's Guide Integrating Sound Level Datalogger Model 407780
User's Guide Integrating Sound Level Datalogger Model 407780 Introduction Congratulations on your purchase of the Extech 407780 Integrating Sound Level Meter. The 407780 with programmable integrating time
More informationRackmount Intelligent Pressure Scanners
Rackmount Intelligent Pressure Scanners NetScanner System 9816/98RK-1 FEATURES ±0.05% Accuracy 100 Hz EU Throughput Autonegotiating 10/100/1G Base T Ethernet - TCP and UDP Protocol Pressure Ranges up to
More informationOWNERS MANUAL. Status Monitor. for Windows 95, 98, ME, NT 4, 2000 & XP. SIGNALCRAFTERS TECH, INC. www.signalcrafters.com
OWNERS MANUAL Status Monitor for Windows 95, 98, ME, NT 4, 2000 & XP SIGNALCRAFTERS TECH, INC. www.signalcrafters.com 57 Eagle Rock Avenue, East Hanover, NJ 07936 Tel: 973-781-0880 or 800-523-5815 Fax:
More informationMonitores Equipos Móviles Especificaciones de Producto
EquipManager -4 F/-20 C to +140 F/+60 C (optional heater available for cold room applications) 0 100% noncondensing User-adjustable threshold 0.3G to 7G 10G (nondestructive)/100g (destructive) Piezoelectric
More informationLIGHTCOMMANDER II 24/6
LIGHTCOMMANDER II 24/6 LIGHTCOMMANDER II 48/6 User s Manual Version 2.X July 1996 Table of Contents 0. Introduction... 4 0.1 How to use your Operator s Manual... 4 0.2 Specifications and Installation...
More informationQuick installation guide for the Vista Quantum QNVR Network Video Recorder
QNVR range Quick Instalation guide Quick installation guide for the Vista Quantum QNVR Network Video Recorder Full manual found on the CD supplied with the NVR Contents SCOPE OF USE... 3 1. FRONT PANEL
More informationHCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply
1. INTRODUCTION HCS-3300/3302/3304 USB Remote Programmable Laboratory Grade Switching Mode Power Supply User Manual This family of efficient, upgraded SMPS with small form factor, auto cross over CV CC,
More informationMidiStream. UHF Wireless MIDI System Operating Manual
MidiStream UHF Wireless MIDI System Operating Manual Introduction Congratulations on your purchase of the MidiStream UHF wireless MIDI system. The MidiStream system is very easy to use, but please take
More informationUser Manual. AS-Interface Programmer
AS-Interface Programmer Notice: RESTRICTIONS THE ZMD AS-INTERFACE PROGRAMMER HARDWARE AND ZMD AS-INTERFACE PROGRAMMER SOFTWARE IS DESIGNED FOR IC EVALUATION, LABORATORY SETUP AND MODULE DEVELOPMENT ONLY.
More information4-Channel Thermometer / Datalogger
USER GUIDE 4-Channel Thermometer / Datalogger RTD and Thermocouple Inputs Model SDL200 Introduction Congratulations on your purchase of the Extech SDL200 Thermometer, an SD Logger Series meter. This meter
More informationMini Amp Gizmo. User s Manual. RJM Music Technology, Inc.
Mini Amp Gizmo User s Manual RJM Music Technology, Inc. Mini Amp Gizmo User s Manual Version 1.1 March 15, 2012 RJM Music Technology, Inc. 2525 Pioneer Ave #1 Vista, CA 92081 E-mail: support@rjmmusic.com
More informationAUTODIALLER / QUICKDIALLER - SA132
AUTODIALLER / QUICKDIALLER - SA132 INSTRUCTION LEAFLET ENGLISH www.thermomax-group.com CONTENTS 1 SETUP AT A GLANCE... 2 2 FOREWORD....... 3 3 INSTALLATION...... 4 4 KEYPAD AND INDICATORS...... 5 SETTING
More informationGSM/3G UMTS/GPS/SMS Data Logger. The King Pigeon S262W S263W Data Logger inbuilt industrial GSM and 3G WCDMA
S262W S263W GSM/3G UMTS/GPS/SMS Data Logger The King Pigeon S262W S263W Data Logger inbuilt industrial GSM and 3G WCDMA module, GPS optional. channel Analog inputs (0-20mA,-20mA,0-5V) support Ultra-Low/Low/High/Ultra-High
More informationGSM-DL2 GSM auto dialer
Introduction GSM-DL2 GSM auto dialer GSM-DL2 is a GSM auto dialer; designed for car alarm, boat alarm, home alarm and other applications. When it is triggered, it dials pre-programmed telephone numbers
More informationVarioControl LinearDrive 720D1 and 720D2
VarioControl LinearDrive 720D1 and 720D2 4624 A FullColour Dimmable LED Driver LINEAdrive DC is a constant voltage LED driver with multiple LED outputs that are controlled over four channels. It is targeted
More informationLIGHTCOMMANDER II 24/6 LIGHTCOMMANDER II 48/6. User s Manual
LIGHTCOMMANDER II 24/6 LIGHTCOMMANDER II 48/6 User s Manual Version 2.59 August 2007 Table of Contents 0. Introduction... 4 0.1 How to use your Operator s Manual... 4 0.2 Specifications and Installation...
More informationSection 16935 TELEPHONE AUTOMATIC DIALER SYSTEM
Section TELEPHONE AUTOMATIC DIALER SYSTEM PART 1 GENERAL 1.01 SYSTEM DESCRIPTION A. Design Requirements: 1. Electronic monitoring system shall interface plant alarms to public telephone system or cellular
More informationDALI DIM/CONVERTER CONTROL (DC NV) 1 10V (0-10 V) analog DALI Converter with (Multi-) Sensor-control and 1 and 2-Switch dim functions
DAI DIM/COVERTER COTRO (DC V) 1 10V (0-10 V) analog DAI Converter with (Multi-) Sensor-control and 1 and 2-Switch dim functions Dim-and Switch Functions: The DAI Dim/Converter Control DC V is suitable
More informationEXPERIMENT 2 TRAFFIC LIGHT CONTROL SYSTEM FOR AN INTERSECTION USING S7-300 PLC
YEDITEPE UNIVERSITY ENGINEERING & ARCHITECTURE FACULTY INDUSTRIAL ELECTRONICS LABORATORY EE 432 INDUSTRIAL ELECTRONICS EXPERIMENT 2 TRAFFIC LIGHT CONTROL SYSTEM FOR AN INTERSECTION USING S7-300 PLC Introduction:
More informationMSITel provides real time telemetry up to 4.8 kbps (2xIridium modem) for balloons/experiments
The MSITel module family allows your ground console to be everywhere while balloon experiments run everywhere MSITel provides real time telemetry up to 4.8 kbps (2xIridium modem) for balloons/experiments
More informationIP Box Camera ACM-5711. Ver. 081016. Hardware User s Manual
IP Box Camera ACM-5711 Ver. 081016 Hardware User s Manual 0 0 PRECAUTIONS 1. Read these instructions All the safety and operating instructions should be read before the product is operated. 2. Heed all
More informationSpeedlink software will run on Windows NT, Windows 7, and Windows 8; it will run on both 32 byte and 64 byte versions of Windows.
Guide to the Speedlink software and drivers. Status Instruments has a range of process control equipment that can be configured using the Speedlink software. Some equipment will connect directly to a Windows
More informationOVERVIEW Playbacks: Shortcuts: Memories: Data Entry Wheels: Touchpad: Master and Blackout:
OVERVIEW The MIDIcon is a USB MIDI control panel designed to work alongside the Elation lighting software packages. The Midicon is USB powered and uses the USB class drivers so that no driver needs to
More informationEVAL-UFDC-1/UFDC-1M-16
Evaluation Board for Universal Frequency-to- Digital Converters UFDC-1 and UFDC-1M-16 EVAL-UFDC-1/UFDC-1M-16 FEATURES Full-Featured Evaluation Board for the Universal Frequency-to-Digital Converters UFDC-1
More informationSupplemental Notes May 20, 1995 SN09 V1.0
Supplemental Notes May 20, 1995 SN09 V1.0 Sequencing with the JV-90 and the VE-Series Voice Expanders The JV- 90 is an 8 part multitimbral synthesizer with 320 Patches, 80 Performances, and 5 Rhythm Sets
More informationSYSTEM 4C. C R H Electronics Design
SYSTEM 4C C R H Electronics Design SYSTEM 4C All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, A outputs. Independent 25
More informationNTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter
NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter Description: The NTE2053 is a CMOS 8 bit successive approximation Analog to Digital converter in a 20 Lead DIP type package which uses a differential
More informationDMX-K-DRV. Integrated Step Motor Driver + (Basic Controller) Manual
DMX-K-DRV Integrated Step Motor Driver + (Basic Controller) Manual DMX-K-DRV Manual page 1 rev 1.33 COPYRIGHT 2007 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.
More informationUPS Monitoring and Management Software
UPS Monitoring and Management Software LEN.MAN.SOF.141 Rev.1.00/2008 User s Guide: Easy-Mon X 1. Configuration Before Easy-Mon X software can display the electrical data of LEONICS UPS, user has to configure
More informationSYSTEM 45. C R H Electronics Design
SYSTEM 45 C R H Electronics Design SYSTEM 45 All in one modular 4 axis CNC drive board By C R Harding Specifications Main PCB & Input PCB Available with up to 4 Axis X, Y, Z, & A outputs. Independent 25
More informationProgrammer s Reference
Programmer s Reference 1 Introduction This manual describes Launchpad s MIDI communication format. This is all the proprietary information you need to be able to write patches and applications that are
More informationHyperAccess Access Control System
Control System We manufacture, an advanced PC based access control solution that will give you control over who has access to your building. With you can control access on hundreds of doors for up to 10,000
More informationDRTS 33. The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationUser Manual. Humidity-Temperature Chart Recorder. Model RH520
User Manual Humidity-Temperature Chart Recorder Model RH520 Introduction Congratulations on your purchase of the Extech RH520 Temperature + Humidity Chart Recorder. The RH520 measures and displays Temperature,
More informationElectric Landing Gear controllers and sequencer LGC12 / LGC 13C
Electric Landing Gear controllers and sequencer LGC12 / LGC 13C Users Guide. Torrent d en Puig, 31. 08358, Arenys de Munt, Barcelona,Catalonia,Spain E-mail: info@xicoy.com. Fax: +34 933 969 743 web: www.xicoy.com
More informationUSER MANUAL V5.0 ST100
GPS Vehicle Tracker USER MANUAL V5.0 ST100 Updated on 15 September 2009-1 - Contents 1 Product Overview 3 2 For Your Safety 3 3 ST100 Parameters 3 4 Getting Started 4 4.1 Hardware and Accessories 4 4.2
More informationCart Interface Installation & Control Board Manual for M38 XP and RX Carts and Legacy M39 Carts
Rubbermaid Medical Solutions Cart Interface Installation & Control Board Manual for M38 XP and RX Carts and Legacy M39 Carts REVISED FEBRUARY 25, 2010 Filename: Cart Interface Installation & Control Board
More informationTutorial for Programming the LEGO MINDSTORMS NXT
Tutorial for Programming the LEGO MINDSTORMS NXT Table of contents 1 LEGO MINDSTORMS Overview 2 Hardware 2.1 The NXT Brick 2.2 The Servo Motors 2.3 The Sensors 3 Software 3.1 Starting a Program 3.2 The
More information500r+ Installation and User Guide
500r+ Installation and User Guide Compatible Equipment 502rUK-50 Watch/Pendant PA. 509rUK-50 Smoke Detector 515rUK-00 10 metre passive infra red movement detector. 525rUK-00 Remote Set/Unset (Full and
More informationICP-CC488. Installation Guide ICP-CC488 Control Panel
ICP-CC488 EN Installation Guide ICP-CC488 Control Panel ICP-CC488 Installation Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems,
More informationLong Distance Industrial Wireless Transmitters and Receivers
Long Distance Industrial Wireless s and Receivers Up to 450 m (1500') Line of Sight Range UWXL Series U Thermocouple, RTD, Temperature, RH, ph, Process Voltage/ Current and Input Models U J, K, T, E, R,
More informationHWg-STE HWg-STE PoE MANUAL
HWg-STE HWg-STE PoE MANUAL www.hw-group.com Page 2 HWg-STE connectors LED indicators Green: Power & Mode Yellow: Link & Activity SENSORS S1 and S2 ports for connecting temperature or humidity sensors.
More informationOption field bus: without bus with profibus DP. Design-Index (Subject to change)
Amplifier / controller cards ED1 Digital amplifier / controller card ED1 for 1 or 2 proportional solenoids 4 analogue inputs, of which 2 for differential inputs 8 digital inputs Card setting via PC, multi-function
More informationMANUAL FOR RX700 LR and NR
MANUAL FOR RX700 LR and NR 2013, November 11 Revision/ updates Date, updates, and person Revision 1.2 03-12-2013, By Patrick M Affected pages, ETC ALL Content Revision/ updates... 1 Preface... 2 Technical
More informationCurrent Loop Application Note 1495
Current Loop Application Note Document No. CLAN1495 International Headquarter B&B Electronics Mfg. Co. Inc. 707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350 USA Phone (815) 433-5100 -- General Fax
More informationDTAP3000 DTSX3000 Control Visualization Software LAS2.0 Data Conversion Guide
User s Manual DTAP3000 DTSX3000 Control Visualization Software LAS2.0 Data Conversion Guide 1st Edition Blank Page < Introduction > i Introduction About this Manual Thank you for purchasing the DTSX3000
More informationManual. EN Appendix. Blue Solar PWM Pro setup and monitoring software
Manual EN Appendix Blue Solar PWM Pro setup and monitoring software EN Appendix Contents 1. Region and language settings 2 2. Download the software 2 3. UnRAR the software 2 4. Install the software 3
More informationIf an occupancy of room is zero, i.e. room is empty then light source will be switched off automatically
EE389 Electronic Design Lab Project Report, EE Dept, IIT Bombay, Nov 2009 Fully-automated control of lighting and security system of a Room Group No: D2 Bharat Bhushan (06d04026) Sravan
More informationHydras 3 LT Quick Start
Catalog Number 6234218 Hydras 3 LT Quick Start SOFTWARE MANUAL December 2005, Edition 2 Hach Company, 2005. All rights reserved. Printed in the U.S.A. Catalog Number 6234218 Hydras 3 LT SOFTWARE MANUAL
More informationCHAPTER 11: Flip Flops
CHAPTER 11: Flip Flops In this chapter, you will be building the part of the circuit that controls the command sequencing. The required circuit must operate the counter and the memory chip. When the teach
More informationx10* CP290 HOME CONTROL INTERFACE PROGRAMMING GUIDE FOR ADVANCED PROGRAMMERS
x10* CP290 HOME CONTROL INTERFACE PROGRAMMING GUIDE FOR ADVANCED PROGRAMMERS 1 TABLE OF CONTENTS 3. Introduction. 6. Programming. 7. RS-232 connections. a. Byte format. 9. Download Base Housecode. IO.
More informationJKW-IP. IP Video Entry System. QuikStart Guide
1210 JKW-IP IP Video Entry System QuikStart Guide This is an abbreviated instruction manual for installation purposes. Please see the JKW-IP Installation Manual and JKW-IP Operation Manual for complete
More informationINSTALLATION/PROGRAMMING INSTRUCTIONS E4KP ENTRYCHECK
Security Door Controls 3580 Willow Lane, Westlake Village, CA 91361-4921 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION/PROGRAMMING INSTRUCTIONS E4KP
More informationTAC I/NETTM MR-VAV-AX. Application Specific MicroRegulator TM
TAC I/NETTM TM TAC s TM has an extensive range ofpre-engineered VAV control sequences, which combined with a fully integrated actuator and airflow transducer, makes it a low Total Installed Cost solution
More informationTebis application software
Tebis application software Input products / ON / OFF output / RF dimmer Electrical / Mechanical characteristics: see product user manual Product reference Product designation TP device RF devices WYC81xQ
More informationEA-200. http://world.casio.com/edu/ Technical Reference. Contents. Sampling... 2 Analog Sampling... 3 Memory... 3 Pulse Sampling...
E Contents EA-200 Technical Reference Sampling... 2 Analog Sampling... 3 Memory... 3 Pulse Sampling... 4 Command Tables... 5 Command 1: Channel Settings... 9 Command 3: Sampling and Trigger Settings...
More informationLegal Notices. Guide Part Number 9329-65008-00 REV A 2/10
Legal Notices This guide is copyrighted 2010 by Avid Technology, Inc., with all rights reserved. Under copyright laws, this guide may not be duplicated in whole or in part without the written consent of
More informationThe modular concept of the MPA-3 system is designed to enable easy accommodation to a huge variety of experimental requirements.
HARDWARE DESCRIPTION The modular concept of the MPA-3 system is designed to enable easy accommodation to a huge variety of experimental requirements. BASE MODULE GO LINE Digital I/O 8 Analog Out AUX 1
More informationM68EVB908QL4 Development Board for Motorola MC68HC908QL4
M68EVB908QL4 Development Board for Motorola MC68HC908QL4! Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com! CONTENTS CAUTIONARY NOTES...3 TERMINOLOGY...3
More informationAC-115 Compact Networked Single Door Controller. Installation and User Manual
AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction...5 1.1 Key Features... 6 1.2 Technical Specifications... 7 2.
More informationProgrammable Logic Controllers
Programmable Logic Controllers PLC Basics Dr. D. J. Jackson Lecture 2-1 Operating systems and application programs A PLC contains a basic operating system that allows for: Downloading and executing user
More informationInstruction Manual RCI-800-XXX. Remote Control Signal Interface
Manufacturers of Process Controls and Instrumentation Instruction Manual Model: Function: Communication: Input: Output: Power: RCI-800-XXX Remote Control Signal Interface XXX=SER: RS-232/485 XXX=MDM Modem
More informationRemote monitoring of Crouzet Millenium 3 Using Netbiter EasyConnect EC220 & Netbiter Argos
Remote monitoring of Crouzet Millenium 3 Using Netbiter EasyConnect EC220 & Netbiter Argos HMS Industrial Networks AB Page 1 (37) History Revision Date Description Responsible 1.11 2012-09-26 Typos SDA
More informationPotentiometer e.t.c. 1/240 with attach to our switching device 2002
Potentiometer e.t.c. 1/240 with attach to our switching device Pos. Type for mounted on: V 6 / D 64 / V 5 / V / S 2 / S 6 / N 6 / P 7 / P 8 1 T 129 Wire-wound potentiometer linear life 10 7 switching cycles
More informationWA Manager Alarming System Management Software Windows 98, NT, XP, 2000 User Guide
WA Manager Alarming System Management Software Windows 98, NT, XP, 2000 User Guide Version 2.1, 4/2010 Disclaimer While every effort has been made to ensure that the information in this guide is accurate
More informationSDN INSTRUCTIONS 07/10, Ver 1.2. Somfy Digital Network (SDN) Installation and Programming
Somfy Digital Network (SDN) Installation and Programming SSoomffyy SSyysst teemss IInncc.. 1 Table of Contents 1 General Information and Features... 3 1.1 ILT2 Motor... 3 1.2 SDN Switches... 4 1.3 ILT2
More informationPRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL
Rev. D PRODUCTIVITY THROUGH INNOVATION 600 CONTROL DIRECT DRIVE TECHNICAL/OPERATION MANUAL 10 BORIGHT AVENUE, KENILWORTH NEW JERSEY 07033 TELEPHONE: 800-524-0273 FAX: 908-686-9317 TABLE OF CONTENTS Page
More informationO C M III. Open Channel Flow Monitor
O C M III Open Channel Flow Monitor Part 1. General 1.1 Scope A. This section describes the requirements for an ultrasonic flow transmitter with sensor and temperature compensation probe. B. Under this
More informationDigital and Analog I/O
70072-0127-07 TECHNICAL NOTE 02/2007 Digital and Analog I/O This document discusses the application and configuration of digital and analog inputs/outputs (I/O). Details are for both onboard I/O and external
More informationDisturbance Recoder SPCR 8C27. Product Guide
Issued: April 1999 Status: Updated Version: C/26.04.2006 Data subject to change without notice Features Versatile digital disturbance recorder module for recording various phenomena in the electric power
More informationAnalog Servo Drive 25A8
Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit
More informationContents Installing the ucal Software on your PC/Laptop ucal Programmer Version Connecting the ucal Programmer to your PC/Laptop
Contents Installing the ucal Software on your PC/Laptop 1 ucal Programmer Version 1 Connecting the ucal Programmer to your PC/Laptop 1 Optional USB Adapter Kit (for ucal) 1 Installing the USB Driver for
More informationOverview. 1. GPS data tracking via GSM SMS / GPRS. 2. GPS data logging in internal memory. 3. Alarm alert via GSM SMS / Dialing / GPRS
Vehicle or Personal Position Tracking Vehicle Status and Speed Tracking Auto Accident Report Global Position System (GPS) Navigation System Anti theft Alarm System Overview 1. GPS data tracking via GSM
More informationAN00140-003: Using Wago CANOpen IO
AN00140-003: Using Wago CANOpen IO Overview Baldor now offers WAGO Modular IO Systems for use with Mint Motion Controllers using the CANOpen field bus interface. The WAGO units provide a very flexible
More informationDataView DVTH Data Logger for Temperature and Humidity
DataView DVTH Data Logger for Temperature and Humidity Logs temperature, humidity, and dew point Built-in real time text and graphical display Stand-alone or PCconnected operation Deep sample memory Battery-powered
More information