RAD-HARD 3.3 V Dual LVDS Dual Transceiver ARQ-LVT002

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "RAD-HARD 3.3 V Dual LVDS Dual Transceiver ARQ-LVT002"

Transcription

1 RAD-HARD 3.3 V Dual LVDS Dual Transceiver ARQ-LVT002 FEATURES Maximum operating frequency: up to 250 MHz (500 Mbps) 3.3V single power supply Logic signal inputs 5V TTL tolerant Driver and Receiver channel-to-channel skew 150ps Maximum high to low and low to high propagation delay 2ns TRI-STATE output control Internal fail-safe circuit Conforms to ANSI TIA/EIA 644a LVDS standard ESD protection ratio: 8kV HBM Cold sparing capability ITAR free Fully space qualified APPLICATIONS Space wire. High speed data transmission in aerospace and avionics onboard systems. Reconfigurable fast communication interfaces at low voltage. DESCRIPTION ARQ-LVT002 is a TIA/EIA-644-A dual BiCMOS flowthrough differential line driver-receiver pair designed for aerospace applications requiring high data rates and low-power dissipation. The device is designed to support data rates in excess of 500 Mbps (250 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The drivers accept LVTTL/LVCMOS input levels and translate them to LVDS output signals. The receivers accept LVDS input signals and translate them to 3.3V CMOS signal levels. In addition the dual LVDS transceiver pair supports a TRI-STATE function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra-low idle power state. The enable signal is common to all four gates. The input buffers of LVDS receiver include an active internal fail-safe circuit that sets the output of the receiver to a known high state when the following conditions occur: one or the two inputs floating or inputs shorted. RADIATION HARDENING PARAMETER MIN TYP MAX UNIT COMMENTS TID Krad SEL MeVcm 2 /mg SET MeVcm 2 /mg More information about radiation hardening features and radiation test conditions is available under request. AVAILABLE OPTIONS OPERATING ORDERING PRODUCT Quality Level PACKAGE TEMPERATURE RANGE NUMBER ARQ-LVT002 S - Space 16-lead CQFP -55 o C to 125 o C ARQ-LVT002S-01 (*) other packaging options, including raw die format, are also available under request. Arquimea Ingeniería, S.L.U. 1

2 ELECTRICAL CHARACTERISTICS Output Drivers PARAMETER SYMBOL MIN TYP MAX UNIT Differential Output Voltage V OD mv Change in magnitude of V OD for complementary output states Δ V OD mv Offset voltage V OS V Change in magnitude of V OS for complementary output states ΔV OS mv Output short circuit current I OS ma Differential output short circuit current I OSD ma Power-off Leakage (1) I OFF -30 ±5 30 μa Output TRI-STATE current I OZ -10 ±3 10 μa Input Receiver Differential input high threshold V HT mv Differential input low threshold V LT mv Common-mode voltage range V CMR -4-5 V Input current I IN -10 ±6 10 μa Digital Input/Output Input high voltage V IH 2-5 V Input low voltage V IL V Output high voltage V OH V Output low voltage (1) V OL V Driver switching characteristics Differential propagation delay high to low t PDHL ns Differential propagation delay low to high t PDLH ns Differential channel-to-channel skew (1) t SKD ps Maximum operating frequency f MAX MHz Receiver switching characteristics Differential propagation delay high to low (2) t PDHL ns Differential propagation delay low to high (2) t PDLH ns Differential channel-to-channel skew (1) t SKD ps Maximum operating frequency f MAX MHz (1) Estimated value (2) Values obtained with the current CMOS logic output pads. These values will be reduced to 2ns max when the new bipolar-based CMOS pads are completed. Arquimea Ingeniería, S.L.U. 2

3 PINOUT DESCRIPTION pin PIN Name Type Direction Description 1 R IN1- Input A Input negative port of receiver R1, LVDS level 2 R IN1+ Input A Input positive port of receiver R1, LVDS level 3 R IN2+ Input A Input positive port of receiver R2, LVDS level 4 R IN2- Input A Input negative port of receiver R2, LVDS level 5 D OUT2- Output A Output negative port of driver D2, LVDS level 6 D OUT2+ Output A Output positive port of driver D2, LVDS level 7 D OUT1+ Output A Output positive port of driver D1, LVDS level 8 D OUT1- Output A Output negative port of driver D1, LVDS level 9 NC No Connection 10 D IN1 Input D Input data for driver D1 11 D IN2 Input D Input data for driver D2 12 VDD PWR Supply voltage 13 GND GND Ground 14 R OUT2 Output D Output data of receiver R2 15 R OUT1 Output D Output data of receiver R1 16 EN Input D Enable Arquimea Ingeniería, S.L.U. 3

4 BLOCK DIAGRAM TYPICAL APPLICATION Arquimea Ingeniería, S.L.U. 4

5 RADIATION TEST PERFORMANCE Radiation test vehicles are sub-circuits of the full device that are used to facilitate testing of their radiation compliance. They include the critical parts of the chip, in order to get insight on the circuit performance after irradiation. Proper radiation test vehicles have been carried out for validating radiation requirements of the key parameters of the ARQ-LVT002, in any radiation environment by any potential user. In a first step, a full test chip will has been designed and fabricated to allow a comprehensive characterization of the radiation degradation of the circuit blocks. Critical circuit parameters have been monitored after radiation up to several irradiation steps in order to observe the progressive degradation. The aim of the test chip with regard to radiation is to gain a better understanding of the circuit performance degradation due to the degradation of its constituents. It also gives designers a more accurate knowledge of the ranges of variation of the critical circuit parameters, for the target radiation levels, so that they can make their designs more robust against those variations at less expense in the general circuit complexity and performance. In a second step, some of the most representative test vehicles for the radiation degradation of the full circuit performance have been implemented in the ARQ-LVT002 device. This way the radiation performance of the full blocks can be evaluated with simple tests with the use of these test vehicles. Furthermore, the test vehicles included in the device give better understanding on the general block degradation for different radiation environments. More information about radiation tests and mitigation techniques for Total Ionizing Dose effects, Single Event Latch-up and Single Event Upsets, is available under request. QUALITY STANDARDS ARQUIMEA INGENIERÍA S.L.U. develops its activities under the premises of quality and sustainability, offering efficient, liable and innovative technologies and solutions to its customers. product line according to military and space standards. ARQUIMEA s Quality Management System meets the requirements of ISO 9100:2010 Aerospace Series, and has been audited and certified by the Spanish Association for Standardization and Certification, AENOR. In order to meet the highest quality and reliability, ARQUIMEA designs and develops its aerospace Arquimea Ingeniería, S.L.U. 5

6 IMPORTANT NOTICE ARQUIMEA INGENIERÍA S.L.U. and its subsidiaries (ARQUIMEA) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers must obtain the latest relevant information before placing orders and must verify that such information is current and complete. All products are sold subject to ARQUIMEA s terms and conditions of sale supplied at the time of order acknowledgment. ARQUIMEA warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with ARQUIMEA s standard warranty. Testing and other quality control techniques are used to the extent ARQUIMEA deems necessary to support this warranty. Except where mandated by legal requirements, testing of all parameters of each product is not necessarily performed. ARQUIMEA assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using ARQUIMEA components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. ARQUIMEA does not warrant or represent that any license, either express or implied, is granted under any ARQUIMEA patent right, copyright, mask work right, or other ARQUIMEA intellectual property right relating to any combination, machine, or process in which ARQUIMEA products or services are used. Information published by ARQUIMEA regarding third-party products or services does not constitute a license from ARQUIMEA to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from ARQUIMEA under the patents or other intellectual property of ARQUIMEA. Reproduction of ARQUIMEA information in ARQUIMEA data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. ARQUIMEA is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of ARQUIMEA products or services with statements different from or beyond the parameters stated by ARQUIMEA for that product or service voids all express and any implied warranties for the associated ARQUIMEA product or service and is an unfair and deceptive business practice. ARQUIMEA is not responsible or liable for any such statements. ARQUIMEA products are not authorized for use in safety-critical applications (such as life support) where a failure of the ARQUIMEA product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of ARQUIMEA products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by ARQUIMEA. Further, Buyers must fully indemnify ARQUIMEA and its representatives against any damages arising out of the use of ARQUIMEA products in such safety-critical applications. Only products designated by ARQUIMEA as military-grade or space-grade meet military or space specifications. Buyers acknowledge and agree that any such use of ARQUIMEA products which ARQUIMEA has not designated as military-grade or space-grade is solely at the Buyer's risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. Arquimea Ingeniería, S.L.U. 6

SDLS068A DECEMBER 1972 REVISED OCTOBER 2001. Copyright 2001, Texas Instruments Incorporated

SDLS068A DECEMBER 1972 REVISED OCTOBER 2001. Copyright 2001, Texas Instruments Incorporated SN54174, SN54175, SN54LS174, SN54LS175, SN54S174, SN54S175, SN74174, SN74175, SN74LS174, SN74LS175, SN74S174, SN74S175 PRODUCTION DATA information is current as of publication date. Products conform to

More information

V OUT. I o+ & I o- (typical) 2.3A & 3.3A. Package Type

V OUT. I o+ & I o- (typical) 2.3A & 3.3A. Package Type July 25 th, 2012 Automotive Grade AUIRS4427S DUAL LOW SIDE DRIVER Features Gate drive supply range from 6 V to 20 V CMOS Schmitt-triggered inputs 3.3V and 5V logic compatible Two independent gate drivers

More information

IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the

More information

LM5030 LM5030 Application: DC - DC Converter Utilizing the Push-Pull Topology

LM5030 LM5030 Application: DC - DC Converter Utilizing the Push-Pull Topology LM5030 LM5030 Application: DC - DC Converter Utilizing the Push-Pull Topology Literature Number: SNVA553 LM5030 Application DC DC Converter Utilizing the Push-Pull Topology 1 Push-Pull Topology D1 L +

More information

SN54LS06, SN74LS06, SN74LS16 HEX INVERTER BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS

SN54LS06, SN74LS06, SN74LS16 HEX INVERTER BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS Convert TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping Diodes Simplify System Design Open-Collector Driver for Indicator Lamps and Relays s Fully Compatible With Most TTL Circuits

More information

Description. Table 1. Device summary. Order codes Temperature range Package Packaging

Description. Table 1. Device summary. Order codes Temperature range Package Packaging Features DIP-8 ESD protection ±15 kv human body model ±8 kv IEC 1000-4-2 contact discharge Operates from a single 3.3 V supply - no charge pump required Interoperable with 5 V logic 1 µa low current shutdown

More information

Application Note AN107

Application Note AN107 Murata Balun for CC253x and CC254x LFB182G45BG2D280 By Fredrik Kervel Keywords Balun LFB182G45BG2D280 CC253x CC254x CC257x CC85xx 1 Introduction Murata s LFB182G45BG2D280 integrated balun is specially

More information

74HC4002; 74HCT General description. 2. Features and benefits. 3. Ordering information. Dual 4-input NOR gate

74HC4002; 74HCT General description. 2. Features and benefits. 3. Ordering information. Dual 4-input NOR gate Rev. 5 26 May 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a dual 4-input NOR gate. Inputs also include clamp diodes that enable the use of current

More information

54LS174,54LS175,DM54LS174,DM54LS175, DM74LS174,DM74LS175

54LS174,54LS175,DM54LS174,DM54LS175, DM74LS174,DM74LS175 54LS174,54LS175,DM54LS174,DM54LS175, DM74LS174,DM74LS175 54LS174 DM54LS174 DM74LS174 54LS175 DM54LS175 DM74LS175 Hex/Quad D Flip-Flops with Clear Literature Number: SNOS290A 54LS174 DM54LS174 DM74LS174

More information

ULN2803A DARLINGTON TRANSISTOR ARRAY

ULN2803A DARLINGTON TRANSISTOR ARRAY 00 ma Rated Collector Current (Single ) High-Voltage s... 0 V Clamp Diodes Inputs Compatible With Various Types of Logic Relay Driver Applications Compatible with ULN2800A Series description The ULN280A

More information

The 74LVC1G11 provides a single 3-input AND gate.

The 74LVC1G11 provides a single 3-input AND gate. Rev. 8 17 September 2015 Product data sheet 1. General description The provides a single 3-input AND gate. The input can be driven from either 3.3 V or 5 V devices. This feature allows the use of this

More information

Order code Temperature range Package Packaging

Order code Temperature range Package Packaging ST485B ST485C Low power RS-485/RS-422 transceiver Features Low quiescent current: 300 µa Designed for RS-485 interface application - 7 V to 12 V common mode input voltage range Driver maintains high impedance

More information

74HC151; 74HCT General description. 2. Features and benefits. 3. Ordering information. 8-input multiplexer

74HC151; 74HCT General description. 2. Features and benefits. 3. Ordering information. 8-input multiplexer Rev. 6 28 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The are 8-bit multiplexer with eight binary inputs (I0 to I7), three select inputs (S0

More information

FIN1108 FIN1108T (Preliminary) LVDS 8 Port High Speed Repeater

FIN1108 FIN1108T (Preliminary) LVDS 8 Port High Speed Repeater 查询 FIN1108 供应商 捷多邦, 专业 PCB 打样工厂,24 小时加急出货 FIN1108 FIN1108T (Preliminary) LVDS 8 Port High Speed Repeater General Description This 8 port repeater is designed for high speed interconnects utilizing Low

More information

Designing Switching Voltage Regulators With TL497A

Designing Switching Voltage Regulators With TL497A Application Report SLVA143 - September 2003 Designing Switching Voltage Regulators With TL497A John Spencer and Eugene J. Tobaben Linear Products Department ABSTRACT Switching voltage regulators, represented

More information

Wireless Subwoofer TI Design Tests

Wireless Subwoofer TI Design Tests Wireless Subwoofer TI Design Tests This system design was tested for THD+N vs. frequency at 5 watts and 30 watts and THD+N vs. power at 00. Both the direct analog input and the wireless systems were tested.

More information

Texas Instruments. FB PS LLC Test Report HVPS SYSTEM AND APPLICATION TEAM REVA

Texas Instruments. FB PS LLC Test Report HVPS SYSTEM AND APPLICATION TEAM REVA Texas Instruments FB PS LLC Test Report HVPS SYSTEM AND APPLICATION TEAM REVA 12/05/2014 1 General 1.1 PURPOSE Provide the detailed data for evaluating and verifying the FB-PS-LLC. The FB-PS-LLC is a Full

More information

ZXCT1081 HIGH VOLTAGE HIGH-SIDE CURRENT MONITOR. Description. Pin Assignments. Applications. Features. Typical Application Circuit ZXCT1081

ZXCT1081 HIGH VOLTAGE HIGH-SIDE CURRENT MONITOR. Description. Pin Assignments. Applications. Features. Typical Application Circuit ZXCT1081 HIGH VOLTAGE HIGH-SIDE CURRENT MONITOR Description Pin Assignments The is a high side current sense monitor with a gain of 10 and a voltage output. Using this device eliminates the need to disrupt the

More information

SN54165, SN54LS165A, SN74165, SN74LS165A PARALLEL-LOAD 8-BIT SHIFT REGISTERS

SN54165, SN54LS165A, SN74165, SN74LS165A PARALLEL-LOAD 8-BIT SHIFT REGISTERS The SN54165 and SN74165 devices SN54165, SN54LS165A, SN74165, SN74LS165A PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments

More information

Multi-Transformer LED TV Power User Guide. Anderson Hsiao

Multi-Transformer LED TV Power User Guide. Anderson Hsiao Multi-Transformer LED TV Power User Guide Anderson Hsiao Operation Range Input Range: 90Vac~264Vac 47Hz~63Hz Dimming Range: Reverse Signal 0V ~ 5V 100Hz ~200Hz 1%~100% Output Range :STBY-5V 20mA~1A 5V

More information

SN28838 PAL-COLOR SUBCARRIER GENERATOR

SN28838 PAL-COLOR SUBCARRIER GENERATOR Solid-State Reliability Surface-Mount Package NS PACKAE (TOP VIEW) description The SN28838 is a monolithic integrated circuit designed to interface with the SN28837 PALtiming generator in order to generate

More information

74HC02; 74HCT02. 1. General description. 2. Features and benefits. Ordering information. Quad 2-input NOR gate

74HC02; 74HCT02. 1. General description. 2. Features and benefits. Ordering information. Quad 2-input NOR gate Rev. 5 26 November 2015 Product data sheet 1. General description 2. Features and benefits The is a quad 2-input NOR gate. Inputs include clamp diodes. This enables the use of current limiting resistors

More information

LM556 LM556 Dual Timer

LM556 LM556 Dual Timer LM556 LM556 Dual Timer Literature Number: SNAS549 LM556 Dual Timer General Description The LM556 Dual timing circuit is a highly stable controller capable of producing accurate time delays or oscillation.

More information

3-to-8 line decoder, demultiplexer with address latches

3-to-8 line decoder, demultiplexer with address latches Rev. 7 29 January 2016 Product data sheet 1. General description The is a high-speed Si-gate CMOS device and is pin compatible with low-power Schottky TTL (LSTTL). The is specified in compliance with JEDEC

More information

Low-power configurable multiple function gate

Low-power configurable multiple function gate Rev. 7 10 September 2014 Product data sheet 1. General description The provides configurable multiple functions. The output state is determined by eight patterns of 3-bit input. The user can choose the

More information

SN54LS381A, SN54S381, SN74LS381A, SN54LS382A, SN74LS382A, SN74S381 ARITHMETIC LOGIC UNITS/FUNCTION GENERATORS

SN54LS381A, SN54S381, SN74LS381A, SN54LS382A, SN74LS382A, SN74S381 ARITHMETIC LOGIC UNITS/FUNCTION GENERATORS PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include

More information

74HC154; 74HCT154. 4-to-16 line decoder/demultiplexer

74HC154; 74HCT154. 4-to-16 line decoder/demultiplexer Rev. 7 29 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a. It decodes four binary weighted address inputs (A0 to A3) to sixteen mutually

More information

8-stage shift-and-store register LED driver

8-stage shift-and-store register LED driver Rev. 8 4 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an 8-stage serial shift register. It has a storage latch associated with each stage

More information

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate

HEF4011B. 1. General description. 2. Features and benefits. 3. Ordering information. 4. Functional diagram. Quad 2-input NAND gate Rev. 6 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad 2-input NAND gate. The outputs are fully buffered for the highest noise

More information

Differential Op Amp Single-Supply Design Techniques

Differential Op Amp Single-Supply Design Techniques Application Note SLOA07 September 00 Differential Op Amp Single-Supply Design Techniques Bruce Carter High Performance Linear ABSTRACT There is a lot of confusion about how to operate a fully differential

More information

Designing Gain and Offset in Thirty Seconds

Designing Gain and Offset in Thirty Seconds Application Report SLOA097 February 2002 Designing Gain and Offset in Thirty Seconds Bruce Carter High Performance Linear ABSTRACT This document discusses how to design an operational amplifier (op amp)

More information

PRODUCT PREVIEW. Windows Media VC-1 Advanced Profile Decoder (v1.02) on C64x+ SPRS437 - JUNE 2007

PRODUCT PREVIEW. Windows Media VC-1 Advanced Profile Decoder (v1.02) on C64x+ SPRS437 - JUNE 2007 Compliant with the expressdsp TM Algorithm Interface Standard (XDAIS) Compliant with the expressdsp Digital Media (XDM) interface Validated on the DM6437 EVM Simple, main, and advanced profile features

More information

74HC238; 74HCT238. 3-to-8 line decoder/demultiplexer

74HC238; 74HCT238. 3-to-8 line decoder/demultiplexer Rev. 4 27 January 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The decodes three binary weighted address inputs (A0, A1 and A2) to eight mutually exclusive

More information

APPLICATION NOTE BUILDING A QAM MODULATOR USING A GC2011 DIGITAL FILTER CHIP

APPLICATION NOTE BUILDING A QAM MODULATOR USING A GC2011 DIGITAL FILTER CHIP SLWA022 APPLICATION NOTE BUILDING A QAM MODULATOR USING A GC2011 DIGITAL CHIP October 6, 1994 1.0 INTRODUCTION This report describes how one can use the GC2011 Digital Filter chip to build digital modulators

More information

74HC157; 74HCT General description. 2. Features and benefits. Quad 2-input multiplexer

74HC157; 74HCT General description. 2. Features and benefits. Quad 2-input multiplexer Rev. 8 28 December 2015 Product data sheet 1. General description The is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL. It is specified in compliance with JEDEC standard

More information

TS391. Low-power single voltage comparator. Description. Features

TS391. Low-power single voltage comparator. Description. Features TS391 Low-power single voltage comparator Datasheet - production data Features Wide single supply voltage range or dual supplies 2 V to 36 V or ±1 V to ±18 V Very low supply current (0.2 ma) independent

More information

1-of-4 decoder/demultiplexer

1-of-4 decoder/demultiplexer Rev. 6 1 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications The contains two 1-of-4 decoders/demultiplexers. Each has two address inputs (na0 and na1, an active

More information

8-bit binary counter with output register; 3-state

8-bit binary counter with output register; 3-state Rev. 3 24 February 2016 Product data sheet 1. General description The is an 8-bit binary counter with a storage register and 3-state outputs. The storage register has parallel (Q0 to Q7) outputs. The binary

More information

74HCU04. 1. General description. 2. Features and benefits. 3. Ordering information. Hex unbuffered inverter

74HCU04. 1. General description. 2. Features and benefits. 3. Ordering information. Hex unbuffered inverter Rev. 7 8 December 2015 Product data sheet 1. General description The is a hex unbuffered inverter. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to

More information

AP1509. 150KHz, 2A PWM BUCK DC/DC CONVERTER. Description. Pin Assignments V IN. Applications. Features. (Top View) GND GND. Output AP1509 GND GND

AP1509. 150KHz, 2A PWM BUCK DC/DC CONVERTER. Description. Pin Assignments V IN. Applications. Features. (Top View) GND GND. Output AP1509 GND GND Description Pin Assignments The series are monolithic IC designed for a stepdown DC/DC converter, and own the ability of driving a 2A load without additional transistor. It saves board space. The external

More information

SN54HC157, SN74HC157 QUADRUPLE 2-LINE TO 1-LINE DATA SELECTORS/MULTIPLEXERS

SN54HC157, SN74HC157 QUADRUPLE 2-LINE TO 1-LINE DATA SELECTORS/MULTIPLEXERS SNHC, SNHC QUADRUPLE 2-LINE TO -LINE DATA SELECTORS/MULTIPLEXERS SCLSB DECEMBER 982 REVISED MAY 99 Package Options Include Plastic Small-Outline (D) and Ceramic Flat (W) Packages, Ceramic Chip Carriers

More information

74HC139; 74HCT139. Dual 2-to-4 line decoder/demultiplexer

74HC139; 74HCT139. Dual 2-to-4 line decoder/demultiplexer Rev. 4 11 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The decodes two binary weighted address inputs (na0, na1) to four mutually exclusive outputs

More information

12-stage shift-and-store register LED driver

12-stage shift-and-store register LED driver Rev. 9 18 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a 12-stage serial shift register. It has a storage latch associated with each stage

More information

Extending Battery Life With the TPS61040 White Light LED Driver

Extending Battery Life With the TPS61040 White Light LED Driver Application Report SLEA004 May 2002 Extending Battery Life With the TPS61040 White Light LED Driver Michael Day Power Management Products / Portable Power DC-DC Applications ABSTRACT This application note

More information

HEF4021B. 1. General description. 2. Features and benefits. 3. Ordering information. 8-bit static shift register

HEF4021B. 1. General description. 2. Features and benefits. 3. Ordering information. 8-bit static shift register Rev. 10 21 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an (parallel-to-serial converter) with a synchronous serial data input (DS), a clock

More information

3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function.

3-input EXCLUSIVE-OR gate. The 74LVC1G386 provides a 3-input EXCLUSIVE-OR function. Rev. 02 3 September 2007 Product data sheet 1. General description The provides a 3-input EXCLUSIVE-OR function. The input can be driven from either 3.3 or 5 V devices. This feature allows the use of these

More information

HEF4520B. 1. General description. 2. Features and benefits. 3. Ordering information. Dual binary counter

HEF4520B. 1. General description. 2. Features and benefits. 3. Ordering information. Dual binary counter Rev. 7 30 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a dual 4-bit internally synchronous binary counter. The counter has an active HIGH

More information

Single Schmitt-trigger inverter

Single Schmitt-trigger inverter Rev. 13 15 March 2016 Product data sheet 1. General description The provides the inverting buffer function with Schmitt-trigger input. It is capable of transforming slowly changing input signals into sharply

More information

74HC138; 74HCT138. 3-to-8 line decoder/demultiplexer; inverting

74HC138; 74HCT138. 3-to-8 line decoder/demultiplexer; inverting Rev. 6 28 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The decodes three binary weighted address inputs (A0, A1 and A2) to eight mutually exclusive

More information

2000 Mixed-Signal Products SLLA014A

2000 Mixed-Signal Products SLLA014A Design Notes 2000 Mixed-Signal Products SLLA014A IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service

More information

74HC377; 74HCT377. 1. General description. 2. Features and benefits. 3. Ordering information

74HC377; 74HCT377. 1. General description. 2. Features and benefits. 3. Ordering information Rev. 4 24 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an octal positive-edge triggered D-type flip-flop. The device features clock (CP)

More information

HEF4518B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual BCD counter

HEF4518B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual BCD counter Rev. 8 19 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications 4. Ordering information The is a dual 4-bit internally synchronous BCD counter. The counter has an

More information

Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking

Description. Table 1. Device summary. Order code Temperature range Package Packaging Marking 14-stage ripple carry binary counter/divider and oscillator Applications Automotive Industrial Computer Consumer Description Datasheet - production data Features Medium speed operation Common reset Fully

More information

BCD to 7-segment latch/decoder/driver

BCD to 7-segment latch/decoder/driver Rev. 7 1 April 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a for liquid crystal and LED displays. It has four address inputs (D0 to D3), an active

More information

Quad 2-input NAND Schmitt trigger

Quad 2-input NAND Schmitt trigger Rev. 9 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a quad two-input NAND gate. Each input has a Schmitt trigger circuit. The gate switches

More information

LM709 LM709 Operational Amplifier

LM709 LM709 Operational Amplifier LM709 LM709 Operational Amplifier Literature Number: SNOS659A LM709 Operational Amplifier General Description The LM709 series is a monolithic operational amplifier intended for general-purpose applications

More information

+5 V Powered RS-232/RS-422 Transceiver AD7306

+5 V Powered RS-232/RS-422 Transceiver AD7306 a FEATURES RS- and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations APPLICATIONS

More information

Filter Design in Thirty Seconds

Filter Design in Thirty Seconds Application Report SLOA093 December 2001 Filter Design in Thirty Seconds Bruce Carter High Performance Analog ABSTRACT Need a filter fast? No theory, very little math just working filter designs, and in

More information

74HC574; 74HCT574. Octal D-type flip-flop; positive edge-trigger; 3-state

74HC574; 74HCT574. Octal D-type flip-flop; positive edge-trigger; 3-state Rev. 7 4 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is an 8-bit positive-edge triggered D-type flip-flop with 3-state outputs. The device

More information

Volume 15 September 2002 Issue 1 SGZN001 QML Class V Space Products from Texas Instruments

Volume 15 September 2002 Issue 1 SGZN001 QML Class V Space Products from Texas Instruments Volume 15 September 2002 Issue 1 SGZN001 QML Class V Space Products from Texas Instruments Integrated circuits are designed for use in a wide range of applications and environments. Some applications are

More information

Fully Differential Op Amps Made Easy

Fully Differential Op Amps Made Easy Application Report SLOA099 - May 2002 Fully Differential Op Amps Made Easy Bruce Carter High Performance Linear ABSTRACT Fully differential op amps may be unfamiliar to some designers. This application

More information

74HC107; 74HCT107. Dual JK flip-flop with reset; negative-edge trigger

74HC107; 74HCT107. Dual JK flip-flop with reset; negative-edge trigger Rev. 5 30 November 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a dual negative edge triggered JK flip-flop featuring individual J and K inputs,

More information

Analog Watchdog Resistor, Capacitor and Discharge Interval Selection Constraints

Analog Watchdog Resistor, Capacitor and Discharge Interval Selection Constraints Application Report SPNA089 - February2003 Analog Watchdog Resistor, Capacitor and Discharge Interval Selection Constraints Kevin Lavery TMS470 Microcontroller ABSTRACT Tolerances on V CCIO, resistor and

More information

Understanding Ratiometric Conversions

Understanding Ratiometric Conversions Application Report SBAA110 March 2004 Understanding Ratiometric Conversions Russell Anderson Data Acquisition Group ABSTRACT The primary factor that establishes the accuracy in most measurement systems

More information

Advanced Regulating Pulse Width Modulators

Advanced Regulating Pulse Width Modulators Advanced Regulating Pulse Width Modulators FEATURES Dual Uncommitted 40V, 200mA Output Transistors 1% Accurate 5V Reference Dual Error Amplifiers Wide Range, Variable Deadtime Single-ended or Push-pull

More information

HEF4027B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual JK flip-flop

HEF4027B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual JK flip-flop Rev. 10 21 March 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a edge-triggered dual JK flip-flop which features independent set-direct (SD), clear-direct

More information

74HC4040; 74HCT4040. 12-stage binary ripple counter

74HC4040; 74HCT4040. 12-stage binary ripple counter Rev. 5 3 February 2016 Product data sheet 1. General description 2. Features and benefits 3. Applications 4. Ordering information The is a with a clock input (CP), an overriding asynchronous master reset

More information

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30

INTEGRATED CIRCUITS. 74LVC08A Quad 2-input AND gate. Product specification IC24 Data Handbook. 1997 Jun 30 INTEGRATED CIRCUITS IC24 Data Handbook 1997 Jun 30 FEATURES Wide supply voltage range of 1.2 V to 3.6 V In accordance with JEDEC standard no. 8-1A Inputs accept voltages up to 5.5 V CMOS low power consumption

More information

TIDA-00667 Test Report Freescale i.mx6 Power Reference Design for Electronic Point of Sale (EPOS)

TIDA-00667 Test Report Freescale i.mx6 Power Reference Design for Electronic Point of Sale (EPOS) TIDA-00667 Test Report Freescale i.mx6 Power Reference Design for Electronic Point of Sale (EPOS) TI Designs TI Designs provide the foundation that you need including methodology, testing and design files

More information

bq2114 NiCd or NiMH Gas Gauge Module with Charge-Control Output Features General Description Pin Descriptions

bq2114 NiCd or NiMH Gas Gauge Module with Charge-Control Output Features General Description Pin Descriptions Features Complete bq2014 Gas Gauge solution for NiCd or NiMH battery packs Charge-control output allows communication to external charge controller (bq2004) Battery information available over a single-wire

More information

4-bit binary full adder with fast carry CIN + (A1 + B1) + 2(A2 + B2) + 4(A3 + B3) + 8(A4 + B4) = = S1 + 2S2 + 4S3 + 8S4 + 16COUT

4-bit binary full adder with fast carry CIN + (A1 + B1) + 2(A2 + B2) + 4(A3 + B3) + 8(A4 + B4) = = S1 + 2S2 + 4S3 + 8S4 + 16COUT Rev. 03 11 November 2004 Product data sheet 1. General description 2. Features The is a high-speed Si-gate CMOS device and is pin compatible with low power Schottky TTL (LSTTL). The is specified in compliance

More information

ARQ-HFDAC001 RAD-HARD, 15b 100 MSPS DAC

ARQ-HFDAC001 RAD-HARD, 15b 100 MSPS DAC ARQ-HFDAC001 RAD-HARD, 15b 100 MSPS DAC FEATURES Up to 15 bit resolution Up to 100MSPS sampling Up to 50MHz analog input THD=74dB @ 5MHz APPLICATIONS Telecom (DVB-S) Aerospace instrumentation Space data

More information

PCIe XMC x8 Lane Adapter

PCIe XMC x8 Lane Adapter Adapts PCI Express XMC to Desktop with P16 High Speed Communications Ports and JN4 Digital IO FEATURES Adapt one XMC PCI Express VITA 42.3 module to a desktop PCI Express slot Supports up to 8 lanes Transparent

More information

SN54F245, SN74F245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS

SN54F245, SN74F245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SNF, SNF SDFS00A MARCH 9 REVISED OCTOBER 99 -State Outputs Drive Bus Lines Directly Package Optio Include Plastic Small-Outline (SOIC) and Shrink Small-Outline (SSOP) Packages, Ceramic Chip Carriers, and

More information

HEF4541B. 1. General description. 2. Features and benefits. 3. Ordering information. Programmable timer

HEF4541B. 1. General description. 2. Features and benefits. 3. Ordering information. Programmable timer Rev. 5 15 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a programmable timer which consists of a 16-stage binary counter, an integrated

More information

Design Note DN004. Folded Dipole Antenna for CC25xx By Audun Andersen. Keywords. 1 Introduction CC2500 CC2550 CC2510 CC2511

Design Note DN004. Folded Dipole Antenna for CC25xx By Audun Andersen. Keywords. 1 Introduction CC2500 CC2550 CC2510 CC2511 Folded Dipole Antenna for CC25xx By Audun Andersen Keywords CC2500 CC2550 CC2510 CC2511 Folded Dipole PCB Antenna 2.4 GHz 1 Introduction This document describes a folded dipole PCB antenna design that

More information

74HC175; 74HCT175. Quad D-type flip-flop with reset; positive-edge trigger

74HC175; 74HCT175. Quad D-type flip-flop with reset; positive-edge trigger Rev. 5 29 January 2016 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a quad positive-edge triggered D-type flip-flop with individual data inputs (Dn)

More information

74HC132; 74HCT132. Quad 2-input NAND Schmitt trigger

74HC132; 74HCT132. Quad 2-input NAND Schmitt trigger Rev. 4 1 December 2015 Product data sheet 1. General description The is a quad 2-input NAND gate with Schmitt-trigger inputs. Inputs include clamp diodes. This enables the use of current limiting resistors

More information

Interfacing Between LVPECL, VML, CML, and LVDS Levels

Interfacing Between LVPECL, VML, CML, and LVDS Levels Application Report SLLA120 - December 2002 Interfacing Between LVPECL, VML, CML, and LVDS Levels Nick Holland ABSTRACT Serial Gigabit Solutions This application report introduces the various interface

More information

74HC14; 74HCT14. Hex inverting Schmitt trigger

74HC14; 74HCT14. Hex inverting Schmitt trigger Rev. 7 19 November 2015 Product data sheet 1. General description The is a hex inverter with Schmitt-trigger inputs. This device features reduced input threshold levels to allow interfacing to TTL logic

More information

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter

NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter NTE2053 Integrated Circuit 8 Bit MPU Compatible A/D Converter Description: The NTE2053 is a CMOS 8 bit successive approximation Analog to Digital converter in a 20 Lead DIP type package which uses a differential

More information

MC10SX1189. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit FIBRE CHANNEL COAXIAL CABLE DRIVER AND LOOP RE- SILIENCY CIRCUIT

MC10SX1189. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit FIBRE CHANNEL COAXIAL CABLE DRIVER AND LOOP RE- SILIENCY CIRCUIT Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit Description The MC10SX1189 is a differential receiver, differential transmitter specifically designed to drive coaxial cables. It incorporates

More information

MC10SX1190. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit

MC10SX1190. Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit Fibre Channel Coaxial Cable Driver and Loop Resiliency Circuit Description The MC10SX1190 is a differential receiver, differential transmitter specifically designed to drive coaxial cables. It incorporates

More information

CDC9843 PC MOTHERBOARD CLOCK SYNTHESIZER/DRIVER WITH 3-STATE OUTPUTS

CDC9843 PC MOTHERBOARD CLOCK SYNTHESIZER/DRIVER WITH 3-STATE OUTPUTS Provides System Clock Solution for Pentium /82430HX/82430VX and PentiumPro 82440FX Chipsets Four Host-Clock Outputs With Programmable Frequency (50 MHz, 60 MHz, and 66 MHz) Six PCI Clock Outputs at Half-CPU

More information

SP490/491 Full Duplex RS-485 Transceivers

SP490/491 Full Duplex RS-485 Transceivers SP490/491 Full Duplex RS-485 Transceivers FEATURES +5V Only Low Power BiCMOS Driver/Receiver Enable (SP491) RS-485 and RS-422 Drivers/Receivers Pin Compatible with LTC490 and SN75179 (SP490) Pin Compatible

More information

August 2001 PMP Low Power SLVU051

August 2001 PMP Low Power SLVU051 User s Guide August 2001 PMP Low Power SLVU051 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service

More information

TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption:

TS555. Low-power single CMOS timer. Description. Features. The TS555 is a single CMOS timer with very low consumption: Low-power single CMOS timer Description Datasheet - production data The TS555 is a single CMOS timer with very low consumption: Features SO8 (plastic micropackage) Pin connections (top view) (I cc(typ)

More information

AMC1100: Replacement of Input Main Sensing Transformer in Inverters with Isolated Amplifier

AMC1100: Replacement of Input Main Sensing Transformer in Inverters with Isolated Amplifier Application Report SLAA552 August 2012 AMC1100: Replacement of Input Main Sensing Transformer in Inverters with Isolated Amplifier Ambreesh Tripathi and Harmeet Singh Analog/Digital Converters ABSTRACT

More information

Design Note DN304. Cebal CCxxxx Development Tools USB Driver Installation Guide By Åsmund B. Bø. Keywords. 1 Introduction

Design Note DN304. Cebal CCxxxx Development Tools USB Driver Installation Guide By Åsmund B. Bø. Keywords. 1 Introduction Cebal CCxxxx Development Tools USB Driver Installation Guide By Åsmund B. Bø Keywords Cebal Driver Windows x86 Windows x64 SmartRF Studio SmartRF Packet Sniffer SmartRF Flash Programmer SmartRF05EB SmartRF04EB

More information

The 74LVC1G04 provides one inverting buffer.

The 74LVC1G04 provides one inverting buffer. Rev. 12 6 ugust 2012 Product data sheet 1. General description The provides one inverting buffer. Input can be driven from either 3.3 V or 5 V devices. These features allow the use of these devices in

More information

Pressure Transducer to ADC Application

Pressure Transducer to ADC Application Application Report SLOA05 October 2000 Pressure Transducer to ADC Application John Bishop ABSTRACT Advanced Analog Products/OpAmp Applications A range of bridgetype transducers can measure numerous process

More information

74HC573; 74HCT573. 1. General description. 2. Features and benefits. Octal D-type transparent latch; 3-state

74HC573; 74HCT573. 1. General description. 2. Features and benefits. Octal D-type transparent latch; 3-state Rev. 7 4 March 2016 Product data sheet 1. General description The is an 8-bit D-type transparent latch with 3-state outputs. The device features latch enable (LE) and output enable (OE) inputs. When LE

More information

HEF4013B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual D-type flip-flop

HEF4013B. 1. General description. 2. Features and benefits. 3. Applications. 4. Ordering information. Dual D-type flip-flop Rev. 9 10 December 2015 Product data sheet 1. General description 2. Features and benefits 3. Applications The is a dual D-type flip-flop that features independent set-direct input (SD), clear-direct input

More information

TIDA Test Results March Portable Point Cloud Generation for 3D Scanning Using DLP Technology

TIDA Test Results March Portable Point Cloud Generation for 3D Scanning Using DLP Technology TIDA-00361 Test Results March 2016 Portable Point Cloud Generation for 3D Scanning Using DLP Technology About Test Results The DLP 3D Scanner Reference Design offers a complete software solution for 3D

More information

74HC2G02; 74HCT2G02. 1. General description. 2. Features and benefits. 3. Ordering information. Dual 2-input NOR gate

74HC2G02; 74HCT2G02. 1. General description. 2. Features and benefits. 3. Ordering information. Dual 2-input NOR gate Rev. 5 27 September 2013 Product data sheet 1. General description 2. Features and benefits 3. Ordering information The is a dual 2-input NOR gate. Inputs include clamp diodes. This enables the use of

More information

L2293Q. Push-pull four channel driver with diodes. Features. Description

L2293Q. Push-pull four channel driver with diodes. Features. Description Push-pull four channel driver with diodes Features 600 ma output current capability per channel 1.2 A peak output current (non repetitive) per channel Enable facility Overtemperature protection Logical

More information

NS5B1G384. Single (NC) Normally Closed SPST Analog Switch

NS5B1G384. Single (NC) Normally Closed SPST Analog Switch Single (NC) Normally Closed SPST Analog Switch The NSB1G384 is Single Pole Single Throw (SPST) high-speed TTL-compatible switch. The low resistance and capacitance characteristics of this switch make it

More information

NLAS7222A. High-Speed USB 2.0 (480 Mbps) DPDT Switch

NLAS7222A. High-Speed USB 2.0 (480 Mbps) DPDT Switch High-Speed USB 2.0 (480 Mbps) DPDT Switch ON Semiconductor s NLAS7222A series of analog switch circuits are produced using the company s advanced sub micron CMOS technology, achieving industry leading

More information

TSL250, TSL251, TLS252 LIGHT-TO-VOLTAGE OPTICAL SENSORS

TSL250, TSL251, TLS252 LIGHT-TO-VOLTAGE OPTICAL SENSORS TSL50, TSL5, TLS5 SOES004C AUGUST 99 REVISED NOVEMBER 995 Monolithic Silicon IC Containing Photodiode, Operational Amplifier, and Feedback Components Converts Light Intensity to Output Voltage High Irradiance

More information

SN54F157A, SN74F157A QUADRUPLE 2-LINE TO 1-LINE DATA SELECTORS/MULTIPLEXERS

SN54F157A, SN74F157A QUADRUPLE 2-LINE TO 1-LINE DATA SELECTORS/MULTIPLEXERS SNFA, SNFA QUADRUPLE -LINE TO -LINE DATA SELECTORS/MULTIPLEXERS SDFS0A MARCH 8 REVISED OCTOBER Buffered Inputs and Outputs Package Optio Include Plastic Small-Outline Packages, Ceramic Chip Carriers, and

More information