ENTWURF ÖVE/ÖNORM EN

Transcription

1 EN Ausgabe: Optical fibre cables Part 5-10: Family specification for outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing (IEC 86A/1496/CDV) Medieninhaber und Hersteller: OVE Österreichischer Verband für Elektrotechnik Austrian Standards Institute Copyright OVE/Austrian Standards Institute Alle Rechte vorbehalten! Nachdruck oder Vervielfältigung, Aufnahme auf oder in sonstige Medien oder Datenträger nur mit Zustimmung gestattet! Verkauf von in- und ausländischen Normen und technischen Regelwerken durch Austrian Standards Institute Heinestraße 38, 1020 Wien Internet: Webshop: Tel.: Fax: Alle Regelwerke für die Elektrotechnik auch erhältlich bei OVE Österreichischer Verband für Elektrotechnik Eschenbachgasse 9, 1010 Wien verkauf@ove.at Internet: Webshop: Tel.: Fax: Hinweis: Aufgrund von Stellungnahmen kann die endgültige Fassung dieser ÖVE/ÖNORM vom vorliegenden Entwurf abweichen. Stellungnahmen (schriftlich) bis an den OVE. ICS Ident (IDT) mit IEC 86A/1496/CDV Ident (IDT) mit FprEN :2013 zuständig OVE/Komitee TK K Kabel und Leitungen

2 EN :2013 Erläuterungen zum Entwurf Die von IEC SC 86A ausgearbeitete Internationale Norm wurde als Entwurf zu einer Europäischen Norm EN :2013 den CENELEC-Mitgliedern zur Abstimmung vorgelegt. Im Falle eines positiven Abstimmungsergebnisses im Sinne der CEN/CENELEC-Regeln wird dieser Entwurf zu einer EN führen. Wie alle Mitgliedsorganisationen von CENELEC ist der OVE grundsätzlich verpflichtet, Europäische Normen in das nationale Normenwerk zu übernehmen und entgegenstehende Normen zurückzuziehen. Der OVE legt hiermit diesen Entwurf eines europäischen Normungsdokumentes der Öffentlichkeit zur Information und Stellungnahme als ÖVE/ÖNORM-Entwurf vor. Da eine Übersetzung in die deutsche Sprache zu diesem Zeitpunkt noch nicht vorhanden ist, wird um die von CENELEC vorgegebene Einspruchsfrist einzuhalten die englischsprachige Fassung des IEC 86A/1496/CDV zur Information und Stellungnahme vorgelegt. Interessenten können das gegenständliche Dokument beim Österreichischen Verband für Elektrotechnik beziehen bzw. in den Text Einsicht nehmen. 2

3 Submitted for parallel voting in CENELEC Soumis au vote parallèle au CENELEC Also of interest to the following committees Intéresse également les comités suivants Project number Numéro de projet IEC/TC or SC: SC86A CEI/CE ou SC: Date of circulation Date de diffusion A/1496/CDV COMMITTEE DRAFT FOR VOTE (CDV) PROJET DE COMITÉ POUR VOTE (CDV) IEC /Ed1 Secretariat / Secrétariat France Closing date for voting (Voting mandatory for P-members) Date de clôture du vote (Vote obligatoire pour les membres (P)) Supersedes document Remplace le document 86A/1456/CD & 86A/1473A/CC Proposed horizontal standard Norme horizontale suggérée Other TC/SCs are requested to indicate their interest, if any, in this CDV to the TC/SC secretary Les autres CE/SC sont requis d indiquer leur intérêt, si nécessaire, dans ce CDV à l intention du secrétaire du CE/SC Functions concerned Fonctions concernées Safety Sécurité EMC CEM CE DOCUMENT EST TOUJOURS À L'ÉTUDE ET SUSCEPTIBLE DE MODIFICATION. IL NE PEUT SERVIR DE RÉFÉRENCE. Environment Environnement Quality assurance Assurance qualité THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED FOR REFERENCE PURPOSES. LES RÉCIPIENDAIRES DU PRÉSENT DOCUMENT SONT INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS, LA NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À FOURNIR UNE DOCUMENTATION EXPLICATIVE. RECIPIENTS OF THIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. Title : IEC /Ed1: Optical fibre cables - Part 5-10: Family specification for outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing Introductory note ATTENTION IEC CENELEC PARALLEL VOTING The attention of IEC National Committees, members of CENELEC, is drawn to the fact that this Committee Draft for Vote (CDV) for an International Standard is submitted for parallel voting. The CENELEC members are invited to vote through the CENELEC online voting system. Copyright 2012 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without permission in writing from IEC. Registered trademark of the International Electrotechnical Commission FORM CDV (IEC)

4 2 CONTENTS FOREWORD Scope Normative references Symbols Family specification for outdoor microduct optical fibre cables, microducts and protected microducts Construction General Optical fibres Installation Performance Tests Installation conditions Tests applicable Mechanical and environmental tests Microduct optical fibre cable Tests applicable Tensile performance Crush Impact Repeated Bending Torsion Kink Bend Temperature cycling Water penetration Ageing Ribbon Strippability Fibre Ribbons Separability Microduct Tests applicable Tensile performance Crush Impact Repeated bending Torsion Kink Bend Microduct route verification test Microduct Pressure Withstand Ageing Protected microduct(s) Tests applicable Tensile performance Crush Impact... 22

5 3 7.5 Repeated bending Kink Bend Microduct route verification test Microduct Pressure Withstand Ageing Annex A Examples of microduct optical fibre cables and microducts (Informative) Annex B (Informative): Family specifications for microduct optical fibre cable, microduct and protected microduct (Blank Detail Specifications and minimum requirements) B.1 Microduct optical fibre cable description B.2 Microduct description B.3 Protected microduct description Annex C (Normative): Product constructions C.1 Outdoor microduct optical fibre cable construction C.2 Microduct construction C.3 Protected microduct construction Annex D (Normative) Transmission requirements D.1 Attenuation of cabled fibre D.2 Fibre bandwidth requirements Annex E : IEC Method Exx - Microduct inner clearance test Figure A1: Microduct optical fibre cables (not to scale) Figure A2: Protected microduct in pre-installed ducts (not to scale) Figure A3: Protected microduct with tight integral outer duct (not to scale) Table 1 Tests applicable for installation performance Table 2 Tests applicable for mechanical and environmental performance of microduct cable Table 3 Tests applicable for mechanical and environmental performance of microduct Table 4 Tests applicable for mechanical and environmental performance of protected microduct Table D.1 Multimode maximum cable attenuation coefficient (db/km) Table D.2 Single-mode maximum cable attenuation coefficient (db/km) premises cabling applications Table D.3 Single-mode maximum cable attenuation coefficient (db/km) all other applications Table D.4 Minimum multimode fibre bandwidth (MHz km)... 32

6 4 INTERNATIONAL ELECTROTECHNICAL COMMISSION OPTICAL FIBRE CABLES Part 5.10: Family specification for outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as IEC Publication(s) ). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC XXX has been prepared by subcommittee XX: TITLE, of IEC technical committee XX: The text of this standard is based on the following documents: FDIS XX/XX/FDIS Report on voting XX/XX/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

7 5 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under " in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. The National Committees are requested to note that for this publication the stability date is THIS TEXT IS INCLUDED FOR THE INFORMATION OF THE NATIONAL COMMITTEES AND WILL BE DELETED AT THE PUBLICATION STAGE.

8 OPTICAL FIBRE CABLES Part 5.10: Family specification for outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing 1 Scope This part of IEC is a family specification that covers outdoor microduct optical fibre cables for installation by blowing and the associated microducts, which together make up a microduct optical fibre cable system. Although primarily designed for use with outdoor microduct applications, the cable products specified herein may be used individually for short lengths in other applications as agreed upon between supplier and customer. These may include short runs inside a building or in other outdoor applications, such as a transition between separate (unconnected) microduct systems, or from a microduct system to some other protective structure such as a cable conduit or tray. Systems built with components covered by this standard are subject to the requirements of sectional specification IEC where applicable. Annex A of this document shows examples of microuct optical fibre cables and microducts. Annex B describes a blank detail specification for outdoor microduct optical fibre cables and the associated microducts, and incorporates some minimum requirements. Detail product specifications may be prepared on the basis of this family specification using Annex B as a guide. Annex C provides normative requirements for microduct optical fibre cables. The parameters specified in this standard may be affected by measurement uncertainty arising either from measurement errors or calibration errors due to lack of suitable standards. Acceptance criteria should be interpreted with respect to this consideration. The number of fibres and microducts tested shall be representative of the microduct optical fibre cable design and should be agreed between customer and supplier. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60304, Standard colours for insulation for low-frequency cables and wires IEC , Optical fibres Part 1-40, Measurement methods and test procedures Attenuation IEC , Optical Fibres - Part 2-10, Product specifications Sectional specification for category A1 multimode fibres IEC , Optical fibres - Part 2-50, Products specification-sectional specification for class B single-mode fibres IEC , Optical fibre cables - Part 1-1: Generic specification - General IEC , Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures IEC : Basic optical cable test procedures Mechanical test methods IEC : Basic optical cable test procedures Environmental test methods IEC : Basic optical cable test procedures Cable elements test methods

9 IEC : Basic optical cable test procedures Electrical test methods IEC : Optical Fibre Cables - Part 2: Indoor optical fibre cables - Sectional specification IEC , Optical fibre cables Part 3: Sectional specification Outdoor cables IEC : Optical Fibre Cables - Part 4: Sectional specification Aerial optical cables along electrical power lines IEC , Optical fibre cables - Part 5: Optical fibre cables- Sectional specification for microduct cabling for installation by blowing IEC , Optical fibre cables Part 5-20: Optical fibre cables Family specification for outdoor microduct fibre units, microducts and protected microducts for installation by blowing IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 202: General tests Measurement of thickness of non-metallic sheath IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 203: General tests Measurement of overall dimensions IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 501: Mechanical tests - Tests for determining the mechanical properties of insulating and sheathing compounds IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 601: Physical Tests - Measurement of the drop-point of filling compounds IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 602: Physical Tests - Separation of oil in filling compounds IEC : Electric and optical fibre cables Test methods for non-metallic materials - Part 604: Physical Tests Measurement of absence of corrosive components in filling compounds 3 Symbols For the purposes of this part of IEC 60794, the following symbols apply. D Minimum wall thickness D Minimum thickness of the outer sheath of the protected microduct D Nominal outer diameter of the microduct cable DS Detail specification ID Nominal inner diameter of the microduct OD Nominal outer diameter of the microduct OD Nominal outer diameter of the protected microduct T A1 Temperature cycling test low-temperature limit (usage and storage) according to IEC , Method F1 T A2 Temperature cycling test secondary low-temperature limit for extended storage temperature range according to IEC , Method F1 T B1 Temperature cycling test high-temperature limit (usage and storage) according to IEC , Method F1 T B2 Temperature cycling test secondary high-temperature limit for extended storage temperature range according to IEC , Method F1 t 1 Temperature cycling dwell time