SRS AIRBAG SECTION SR CONTENTS RESTRAINTS SR-1 PRECAUTION... 2 PREPARATION... 3 ON-VEHICLE REPAIR... 4

Transcription

1 RSTRTS ST S R TTS RUT... 2 RUTS... 2 recaution for Supplemental Restraint System (S) "R " and "ST T R-T- SR"...2 Service...2 RRT... 3 RRT... 3 Special Service Tool...3 -VH RR... 4 RVR R U... 4 xploded View...4 Removal and nstallation...4 SR... 6 xploded View...6 Removal and nstallation...6 RT SSR R U... 8 xploded View...8 Removal and nstallation...8 S URT R U...10 xploded View...10 Removal and nstallation...10 RT S R U...12 xploded View...12 Removal and nstallation...12 RSH Z SSR...14 xploded View...14 Removal and nstallation...14 S R (STT) SSR...15 xploded View...15 Removal and nstallation...15 SS SSR UT...16 xploded View...16 Removal and nstallation...16 RT ST T R-TSR...18 Removal and nstallation...18 SS R U ST T R-TSR...19 aution for ir ag odule and Seat elt re-tensioner

2 < RUT > RUT RUTS RUTS recaution for Supplemental Restraint System (S) "R " and "ST T R-TSR" : The Supplemental Restraint System such as R and ST T R-TSR, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The S system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. nformation necessary to service the system safely is included in the S and S section of this Service anual. WR: To avoid rendering the S inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized SS/T dealer. mproper maintenance, including incorrect removal and installation of the S, can lead to personal injury caused by unintentional activation of the system. or removal of Spiral able and ir ag odule, see the S section. o not use electrical test equipment on any circuit related to the S unless instructed to in this Service anual. S wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors. Service : o not use electrical test equipment to check S circuits unless instructed to in this Service anual. efore servicing the S, turn ignition switch, disconnect both battery cables and wait at least 3 minutes. or approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pretensioner to deploy. Therefore, do not work on any S connectors or wires until at least 3 minutes have elapsed. iagnosis sensor unit must always be installed with their arrow marks pointing towards the front of the vehicle for proper operation. lso check diagnosis sensor unit for cracks, deformities or rust before installation and replace as required. The spiral cable must be aligned in the neutral position since its rotations are limited. o not turn steering wheel and column after removal of steering gear. Handle air bag module carefully. lways place driver and front passenger air bag modules with the pad side facing upward and seat mounted front side air bag module standing with the stud bolt side facing down. onduct self-diagnosis to check entire S for proper function after replacing any components. fter air bag inflates, the front instrument panel assembly should be replaced if damaged. lways replace instrument panel pad following front passenger air bag deployment. -2

3 < RRT > RRT RRT Special Service Tool RRT The actual shapes of ent-oore tools may differ from those of special service tools illustrated here. : Tool number Tool name escription V ir bag module bracket nchoring air bag module S-T354 V eployment tool isposing of air bag module and front seat belt pre-tensioner S-T357 V eployment tool adapter for driver air bag module (Yellow and orange connectors) eployment tool adapter for seat belt pre-tensioner (Yellow connector) eployment tool adapter for seat belt pre-tensioner2 (range connector) eployment tool adapter for front passenger air bag module (Yellow and orange connector) H0184 onnecting between the deployment tool and driver air bag module onnecting between the deployment tool and front seat belt pre-tensioner onnecting between the deployment tool and seat belt pre-tensioner2 onnecting between the deployment tool and front passenger air bag module V eployment tool adapter for front side air bag module, side curtain air bag module onnecting between the deployment tool and front side air bag module, side curtain air bag module H0112-3

4 -VH RR RVR R U xploded View RVR R U : H0189ZZ 1. Steering wheel 2. river air bag module 3. Steering switch Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. lways work from the side of air bag module. o not work in front of it. o not use air tools or electric tools for servicing. 1. ocate retaining clip access hole (left/right) and insert a 5.0 mm diameter, blunt-ended tool (). H0190ZZ 2. ress upward on retaining clip (1) until driver air bag module is released from steering wheel. H0224ZZ -4

5 RVR R U 3. ift the driver air bag module from the steering wheel. 4. isconnect the driver air bag module and horn connectors, then remove the driver air bag module. T: or installing/removing driver air bag module connector, insert thin screwdriver wrapped in tape into notch, lift lock and remove connector. nstall connector with lock raised, and push lock into connector. fter installing the connector, check that the lock is pushed securely into it. lways place air bag module with pad side facing upward. : Upward o not insert any foreign objects (screwdriver, etc.) into air bag module. o not disassemble air bag module. o not expose the air bag module to temperatures exceeding 90 (194 ). o not allow oil, grease or water to come in contact with the air bag module. H0953 H0191ZZ Replace the air bag module if it has been dropped or sustained an impact. H0009ZZ STT nstall in the reverse order of removal. o not damage the harness while installing. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -5

6 SR xploded View SR : H0193ZZ 1. Spiral cable 2. Steering wheel 3. river air bag module harness connectors 4. Steering column assembly 5. Steering column cover (lower) 6. Steering lock escation 7. Steering column cover (upper) Removal and nstallation RV : WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. o not use air tools or electric tools for servicing. 1. Remove the driver air bag module. Refer to -4, "Removal and nstallation". 2. Remove the steering wheel. Refer to ST-9, "Removal and nstallation". 3. Remove the column cover (upper/lower). Refer to -11, "xploded View". 4. isconnect spiral cable body side connectors (). T: isconnect spiral cable body side connectors after remove the spiral cable. H0194ZZ 5. Remove spiral cable fixing screws, and pawls (left/right). 6. ull out forward the spiral cable. o not disassemble the spiral cable. o not apply lubricant to the spiral cable. o not allow oil, grease, detergent or water to come in contact with the spiral cable. -6

7 SR o not make an impact the spiral cable by dropping etc. Replace the spiral cable if it has been dropped or sustained an impact. STT nstall in the reverse order of removal. The spiral cable may snap by steering operation if the cable is installed in an improper position. The neutral position is set as follows. Turn carefully the spiral cable clockwise to the end position. Then turn it counterclockwise (about 2 and half turns) and stop turning at the point () on which the stopper insertion holes are in the same position. The service part is installed in the neutral position by the stopper and can be set without adjusting after the stopper is removed. o not over turn spiral cable or beyond number of turns required. (These will cause cable snap.) djust the spiral cable locating pin () to the steering wheel locating pin hole (). Secure the air bag harness with the harness fixing hook. H0009ZZ H0013ZZ n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -7

8 RT SSR R U < -VH RR > RT SSR R U xploded View : H assenger air bag modulel 2. nstrument panel SSY Refer to -4, "omponents" for symbols in the figure. Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. lways work from the side of air bag module. o not work in front of it. o not use air tools or electric tools for servicing. 1. Remove the glove box assemblies. Refer to -12, "Removal and nstallation". 2. Remove the nstrument lower assist panel. Refer to -12, "Removal and nstallation". 3. isconnect passenger air bag module harness connector (). (1): assenger air bag module H0196ZZ 4. Remove the passenger air bag module fixing bolts. -8

9 RT SSR R U 5. isconnect rearward pawl () first by rotating passenger air bag car forwards, rear of air bag can then be pulled downwards to disconnect toward pawl (). : Vehicle rear lways place air bag module with pad side facing upward. : Upward o not insert any foreign objects (screwdriver, etc.) into air bag module. o not disassemble air bag module. o not use old fixing bolts after removal; replace with new bolts. o not expose the air bag module to temperatures exceeding 90 (194 ). o not allow oil, grease or water to come in contact with the air bag module. Replace the air bag module if it has been dropped or sustained an impact. H0197ZZ H0198ZZ H0009ZZ STT nstall in the reverse order of removal. o not damage the harness while installing. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -9

10 S URT R U xploded View S URT R U : H Side curtain air bag module 2. Side curtain air bag inflator : lip : etal clip Refer to -4, "omponents" for symbols in the figure. Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. o not use air tools or electric tools for servicing. 1. Remove the headlining. Refer to T-21, "Removal and nstallation". 2. Remove the side curtain air bag module connector. H Remove the side air bag module fixing bolts and clips. 4. Remove the side curtain air bag module. o not insert any foreign objects (screwdriver, etc.) into air bag module. o not disassemble air bag module. o not use old fixing nut after removal; replace with new bolts. o not expose the air bag module to temperatures exceeding 90 (194 ). o not allow oil, grease or water to come in contact with the air bag module. -10

11 S URT R U Replace the air bag module if it has been dropped or sustained an impact. H0009ZZ STT nstall in the reverse order of removal. o not damage the air bag harness. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -11

12 RT S R U xploded View RT S R U : H ront side air bag module 2. ront seatback flame. ront side air bag module connector Refer to -4, "omponents" for symbols in the figure. Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. lways work from the rear of the front side air bag module. o not use air tools or electric tools for servicing. 1. Remove the front seat. Refer to S-15, "Removal and nstallation". 2. Remove the seatback trim and pad. Refer to S-13, "xploded View". 3. Remove the side air bag module fixing nut, and/or harness connector. 4. Remove the side air bag module. lways place air bag module with pad side facing upward. : Upward H0227ZZ o not insert any foreign objects (screwdriver, etc.) into air bag module. o not disassemble air bag module. o not use old fixing nut after removal; replace with new nut. o not expose the air bag module to temperatures exceeding 90 (194 ). o not allow oil, grease or water to come in contact with the air bag module. -12

13 RT S R U Replace the air bag module if it has been dropped or sustained an impact. H0009ZZ STT nstall in the reverse order of removal. o not damage the air bag harness. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -13

14 RSH Z SSR xploded View RSH Z SSR : H rash zone sensor. Harness connector Refer to-4, "omponents" for symbols in the figure. Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. o not use air tools or electric tools for servicing. 1. Remove the crash zone sensor fixing nuts. 2. isconnect harness connector, and then remove crash zone sensor. Replace the crash zone sensor if it has been dropped or sustained an impact. o not use old fixing nuts after removal; replace with new nuts. Replace the crash zone sensor of deployed S driver air bag and deployed S front passenger air bag. H0009ZZ STT nstall in the reverse order of removal. o not damage the crash zone sensor harness. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -14

15 S R (STT) SSR S R (STT) SSR xploded View : Satellite sensor Refer to -4, "omponents" for symbols in the figure. Removal and nstallation H0201 : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. o not use air tools or electric tools for servicing. 1. Remove the front seat belt. Refer to S-6, "ST T RTRTR : xploded View". 2. Remove the side air bag (satellite) sensor fixing nuts. 3. isconnect harness connector and then remove side air bag (satellite) sensor. Replace the side air bag (satellite) sensor if it has been dropped or sustained an impact. o not use old fixing nuts after removal; replace with new nuts. Replace the satellite sensor of deployed S front side air bag and deployed S side curtain air bag. H0009ZZ STT nstall in the reverse order of removal. o not damage the satellite sensor harness. n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". -15

16 SS SSR UT xploded View SS SSR UT : H iagnosis sensor unit. Harness connectors Refer to -4, "omponents" for symboles in the figure. Removal and nstallation : RV WR: efore servicing, turn ignition switch, disconnect both battery terminals and wait at least 3 minutes. efore disconnecting the air bag sensor unit harness connector, be sure to disconnect the each harness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by static electricity and pre-tensioner seat belt operation. o not use air tools or electric tools for servicing. 1. isconnect each connector of all air bag modules and pre-tensioner seat belts. 2. Remove the center console assembly. Refer to -18, "xploded View". 3. isconnect diagnosis sensor unit harness connectors. 4. Remove fixed bolts and ground bolt, and then remove diagnosis sensor unit. Replace the diagnosis sensor unit if it has been dropped or sustained an impact. o not use old fixing bolts after removal; replace with new bolts. Replace the diagnosis sensor unit of deployed S air bag and deployed S front seat belt pre-tensioner. STT nstall in the reverse order of removal. o not damage the diagnosis sensor harness. H0009ZZ -16

17 SS SSR UT n case that malfunction is detected by the air bag warning lamp, reset by the self-diagnosis function and delete the memory by SUT-. n case that malfunction is still detected after the above operations, perform self-diagnosis to repair malfunctions. fter the work is completed, check that no malfunctioning system is detected by air bag warning lamp. Refer to -10, "iagnosis escription". U SRT. fter replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the vehicle as equipped. Specification U SRT o. H RH odels with driver and passenger air bags, seat belt pre-tensioners, seat belt pre-tensioner2, side air bags and curtain air bags odels with driver and passenger air bags, seat belt pre-tensioners, seat belt pre-tensioner2, side air bags and curtain air bags

18 RT ST T R-TSR RT ST T R-TSR Removal and nstallation : or removal and installation procedures, refer to S-6, "ST T RTRTR : xploded View". -18

19 SS R U ST T R-TSR < -VH RR > SS R U ST T R-TSR aution for ir ag odule and Seat elt re-tensioner : efore disposing of air bag module and seat belt pre-tensioner, or vehicles equipped with such systems, deploy the systems. f such systems have already been deployed due to an accident, dispose of them as indicated in isposing of ir ag odule and Seat elt re-tensioner. When deploying the air bag module and seat belt pre-tensioner, always use the Special Service Tool; eployment tool (SST: V ). When deploying the air bag module and seat belt pre-tensioner,stand at least 5 m (16 ft) away from the deployment component. When deploying air bag module and seat belt pre-tensioner, a fairly loud noise is made, followed by smoke being released. The smoke is not poisonous,however, be careful not to inhale smoke since it irritates the throat and can cause choking. lways activate one air bag module at a time. ue to heat, leave air bag module unattended for more than 30 minutes after deployment. lso leave seat belt pre-tensioner unattended for more than 10 minutes after deployment. Wear gloves when handling a deployed air bag module and seat belt pre-tensioner. ever apply water to the deployed air bag module and seat belt pre-tensioner. Wash your hands after finishing work. lace the vehicle outdoors with an open space of at least 6 m (20 ft) on all sides when deploying air bag module and seat belt pre-tensioner while mounted in vehicle. Use a volt meter to make sure the vehicle battery is fully charged. o not dispose of the air bag module and seat belt pre-tensioner undeployed. H YT T onnecting to attery The battery must show voltage of 9.6 V or more. Remove the battery from the vehicle and place it on dry wood blocks approximately 5 m (16 ft) away from the vehicle. Wait 3 minutes after the vehicle battery is disconnected before proceeding. onnect red clip of deployment tool () to battery positive terminal and black clip to negative terminal. heck that the polarity is correct. The right side lamp in the tool, marked deployment tool power, should glow with a green light. f the right side lamp glows red, reverse the connections to the battery. eployment Tool heck ress the deployment tool switch () to the position. The left side lamp in the tool, marked air bag connector voltage should illuminate (). f it does not illuminate, replace the deployment tool (). H0204ZZ ir ag eployment Tool amp llumination hart (attery onnected) H0205ZZ Switch operation eft side lamp, green* R TR VT Right side lamp, green* YT T WR -19

20 SS R U ST T R-TSR < -VH RR > *: f this lamp glows red, the tool is connected to the battery incorrectly.reverse the connections and check the lamp glows green. YT R U (UTS VH) eployment of river ir ag odule (utside of Vehicle) 1. Unless the vehicle is being scrapped, deploying the air bag in the vehicle is not recommended. This may cause damage to the vehicle interior. nchor air bag module bracket (SST: V ) () in a vice secured to a firm foundation deployment. H0208ZZ 2. Using wire (), secure air bag module (1) to air bag module bracket (SST: V ) () at four places. Use wire of at least 1 mm (0.04 in) diameter. f a gap exists between air bag module and air bag module bracket, use a piece of wood () inserted in the gap to stabilize the air bag module. 3. irmly secure air bag module bracket (SST: V ) () with air bag module attached, in a vise (). H0206ZZ 4. onnect deployment tool adapter (SST: V ) () to air bag module (1) and deployment tool connector (SST: V ) (). H0207ZZ 5. onnect red clip of deployment tool () to battery positive terminal and black clip to negative terminal (). 6. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 7. ress the button on the deployment tool (). The left side lamp on the tool, marked air bag connector voltage, will illuminate and the air bag module (1) will deploy. When deploying the driver air bag module, stand at least 5 m (16 ft)away from the air bag module. H0209ZZ YT R U (UTS VH) eployment of ront assenger ir ag odule (utside of Vehicle) -20

21 SS R U ST T R-TSR < -VH RR > 1. irmly secure air bag module bracket (SST: V ) () in a vise. 2. Using wire, secure air bag module to air bag module bracket (SST: V ) () at two places. Use wire of at least 1 mm (0.04 in) diameter. H0208ZZ H0210ZZ 3. onnect deployment tool (SST: V ) () and deployment tool adapter (SST: V ) () to front passenger air bag module connector (1). 4. onnect red clip of deployment tool () to battery positive terminal and black clip to negative terminal (). 5. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 6. ress the button on the deployment tool (). The left side lamp on the tool, marked air bag connector voltage, will illuminate and the air bag module (1) will deploy. When deploying the front passenger air bag module, do not stand on the deploying side. Stand at least 5 m (16 ft) away from the air bag module. YT R U (UTS VH) eployment of Side urtain ir ag odule (utside of Vehicle) H0211ZZ H0209ZZ -21

22 SS R U ST T R-TSR < -VH RR > 1. ut the inflator (2) from side curtain air bag module (1). H0064ZZ 2. onnect deployment tool (SST: V ) () and deployment tool adapter (SST: V ) () to the inflator. H0065ZZ 3. ut the inflator connected with the deployment tool (SST: V ) and deployment tool adapter (SST: V ) into a tire without a wheel. H ut the tire with the inflator (1) onto another tire without wheel.dd an additional tire without a wheel and then a tire mounted on a wheel on top. Tie all tires together with a strap in order keep them standing. 5. onnect red clip of deployment tool () to battery positive terminal and black clip to negative terminal. 6. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 7. ress the button on the deployment tool (). The left side lamp on the tool, marked air bag connector voltage, will illuminate and the air bag module inflator (1) will deploy. H1173 When deploying the side curtain air bag module, stand at least 5 m (16ft) away from the side curtain air bag module. YT R U (UTS VH) eployment of ront Side ir ag odule (utside of Vehicle) -22

23 SS R U ST T R-TSR < -VH RR > 1. ake 6.5 mm (0.256 in) diameter hole () in air bag module bracket (SST: V ) () at the position shown in figure. 2. irmly secure air bag module bracket in a vise. 3. nsert one bolt through air bag module bracket and air bag module upper side holes, and fix them with one 6 bolt/nut. nsert wire through air bag module bracket and air bag module lower side holes, and fix them. Using wire, of at least 1 mm (0.04 in) diameter. 4. onnect deployment tool (SST: V ) () and deployment tool adapter (SST: V ) () to air bag module (1) connector. H0225ZZ H0226ZZ 5. onnect red clip of deployment tool (SST: V ) (),() to battery positive terminal and black clip to negative terminal (). 6. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 7. ress the button on the deployment tool. The left side lamp on the tool, marked air bag connector voltage, will illuminate and the air bag module (1) will deploy. When deploying the front side air bag module, stand at least 5 m (16ft) away from the air bag module. H0212ZZ YT ST T R-TSR (UTS VH) eployment of ront Seat elt re-tensioner (utside of Vehicle) 1. irmly grip pre-tensioner (1) in a vise () and cut off the webbing. H0068ZZ -23

24 SS R U ST T R-TSR < -VH RR > 2. onnect deployment tool (SST: V ) () and deployment tool adapter (SST: V ) () yellow connector to front seat belt pre-tensioner (1). 3. onnect red clip of deployment tool to battery positive terminal and black clip to negative terminal (). 4. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 5. ress the button on the deployment tool. The left side lamp on the tool, marked seat belt pre-tensioner connector voltage, will illuminate and the seat belt pre-tensioner (1) will deploy. When deploying the front seat belt pre-tensioner, stand at least 5 m(16 ft) away from the seat belt pre-tensioner. YT ST T R-TSR (UTS VH) eployment of ront Seat elt re-tensioner 2 (utside of Vehicle) 1. isconnect the webbing of seat belt pre-tensioner 2 (1). H0214ZZ H0070ZZ 2. onnect deployment tool (SST: V ) () and deployment tool adapter (SST: V ) () orange connector to seat belt pre-tensioner 2 (1). H0071ZZ 3. ut the seat belt pre-tensioner 2 (1) connected with the deployment tool into a tire without a wheel. H

25 SS R U ST T R-TSR < -VH RR > 4. onnect red clip of deployment tool () to battery positive terminal and black clip to negative terminal. 5. The lamp on the right side of the tool, marked deployment tool power, should glow green, not red. 6. ress the button on the deployment tool (). The left side lamp on the tool, marked seat belt pre-tensioner 2 connector voltage, will illuminate and the seat belt pre-tensioner 2 (1) will deploy. When deploying the front seat belt pre-tensioner 2, stand at least 5 m(16 ft) away from the seat belt pre-tensioner 2. SS R U ST T R-TSR eployed air bag module and seat belt pre-tensioner are very hot. efore disposing of air bag module and seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag before disposal. ever apply water to a deployed air bag module or seat belt pre-tensioner. Wear gloves when handling a deployed air bag moduleor seat belt pre-tensioner. o poisonous gas is produced upon air bag module deployment. However,be careful not to inhale gas since it irritates the throat and can cause choking. o not disassemble air bag module and seat belt pre-tensioner. ir bag module and seat belt pre-tensioner cannot be reused. Wash your hands clean after finishing work. H1173 S276H -25