ATyS Automatic and remotely operated transfer switches from 125 to 3200 A
|
|
|
- Tiffany Walker
- 7 years ago
- Views:
Transcription
1 atys-p_001_b atys_d_001_a_1_cat ATyS p I-0-II 4P ATyS d I-0-II 4P Function The ATyS are three-phase motorised transfer switches with positive break indication. They enable the on load transfer of two three-phase supplies via remote volt-free contacts, from either an external automatic controller, using pulse logic, or a switch for a very basic version. The most pronounced version in automatic mode enable the monitoring of, and the on load transfer switching between, two power supply sources, in accordance with the parameters configured via pushbuttons and an LCD screen. They are intended for use in low voltage power systems where interruption of the load supply is acceptable during transfer. Description This quick-acting source transfer switch incorporates: 1. Power Section: transfer switch assembly with inherent mechanical interlock 2. Front: switch number 1 terminals (3 or 4 pole) 3. Back-plate mounting fixing lugs 4. Back: switch number 2 terminals (3 or 4 pole) 5. Switch position indication window: I (On) O (Off) II (On) 6. ATS control module with integrated dual power supply 7. Motorized Control Unit 8. Motor housing 9. Green LED Indication: power 10. Auto / Manual mode selector switch 11. Emergency manual operation Direct Handle 12. Red LED Indication: Product Unavailable / Manual Mode / Fault Condition 13. Padlocking facility (up to 3 padlocks of dia. 4 8mm) Facility for locking all controls in the zero position using a RONIS EL11AP Lock 14. Output contacts x 4 (position indication I-O-II and product availability outputs) 15. Input contacts 16. Sliders for terminal shields 17. Emergency manual operation shaft location (accessible only in manual mode) References Description No. of poles Part number Aux. supply Switch type Application r 3 P *** 4 P *** Remote Transfer Remote Transfer Switch Equipment d 3 P *** Switch (RTS) 4 P *** Dual power supply t 3 P *** Automatic controller to manage mains/ 230 VAC 4 P *** mains applications g 3 P *** Automatic Transfer Automatic controller to manage mains/ 4 P *** Switch (ATS) genset applications p 3 P *** Functions for energy management 4 P *** communication options ** - stands for a two caracters of a partnumber depending on the rating of the switch 2 Implementation of standard IEC / EN SOCOMEC
2 Characteristics according to IEC and IEC to 630 A / B3 to B5 Thermal current I th at 40 C 125 A 160 A 200 A 2 A 315 A 400 A 0 A 630 A Frame size B3 B3 B3 B4 B4 B4 B5 B5 (V) (power circuit) Rated impulse withstand voltage Uimp (kv) (power circuit) (V) (operation circuit) Rated impulse withstand voltage Uimp (kv) (operation circuit) (A) according to IEC Rated voltage Utilisation category A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) 415 VAC AC-31 B VAC AC-32 B VAC AC-33 B (A) according to IEC Rated voltage Utilisation category A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) 415 VAC AC-20 A / AC-20 B 125/ / /200 2/2 315/ /400 0/0 630/ VAC AC-21 A / AC-21 B 125/ / /200 2/2 315/ /400 0/0 630/ VAC AC-22 A / AC-22 B 125/ / /200 2/2 315/ /400 0/0 630/ VAC AC-23 A / AC-23 B 125/ / / / / /400 0/0 630/630 0 VAC AC-20 A / AC-20 B 125/ / /200 2/2 315/ /400 0/0 630/630 0 VAC AC-21 A / AC-21 B 125/ / /200 2/2 315/ /400 0/0 630/630 0 VAC AC-22 A / AC-22 B 125/ / / /2 200/ /400 0/0 0/0 0 VAC AC-23 A / AC-23 B 80/80 80/80 80/80 200/ / / / /400 Fuse protected short-circuit withstand as per IEC at 690 VAC Prospective short-circuit current ( rms) 100 (2) 100 (2) (2) Associated fuse rating (A) Circuit breaker protected short-circuit withstand with any circuit breaker that ensures tripping in less than 0.3s (4) Rated short-time withstand current 0.3s I cw ( rms) 12 (2) 12 (2) 12 (2) Rated short-circuit withstand without protection Rated short-time withstand current 60ms I cw ( rms) as per IEC at 415 VAC 10 (3) 10 (3) 10 (3) Rated short-time withstand current 1s I cw ( rms) as per IEC at 690 VAC 7 (2) 7 (2) 7 (2) Rated peak withstand current ( peak) as per IEC at 690 VAC Connection Maximum Cu cable cross-section (mm²) x 1 Minimum Cu busbar cross-section (mm²) 2 x 30 x 5 Maximum Cu cable cross-section (mm²) x x 300 Maximum Cu busbar width (mm) Tightening torque mini / maxi (Nm) 9/13 9/13 9/13 20/26 20/26 20/26 20/26 20/26 Switching time (Standard setting) I - II or II - I (s) I-0 or 0-II (s) Duration of "electrical blackout" I - II (s) Power supply min / max (VAC) 166/ / / / / / / /332 Control supply power demand Power supply 230 VAC inrush / nominal (VA) - 184/92 184/92 184/92 276/ / / /1 276/1 Power supply 230 VAC inrush / nominal (VA) - d, t, g, p 206/ / / / / / / /172 Mechanical characteristics Durability (number of operating cycles) Weight 3/4 P (kg) 5.7/ / / / / / / /14.0 Weight d 3/4 P (kg) 6.3/ / / / / / / /14.6 Weight r, t, g, p 3/4 P (kg) 6.8/ / / / / / / /15.1 (1) Category with index A = frequent operation - Category with index B = infrequent operation. (2) At 415 VAC. (3) At 30ms. (4) Value for coordination with any circuit-breaker that ensures tripping in less than 0.3s. For coordination with specific circuit-breaker references, higher short-circuit current values are available. Please consult us. SOCOMEC - Implementation of standard IEC / EN
3 800 to 3200 A / B6 to B8 Thermal current I th at 40 C 800 A 1000 A 12 A 1600 A 2000 A 20 A 3200 A Frame size B6 B6 B6 B7 B8 B8 B8 (V) (power circuit) Rated impulse withstand voltage Uimp (kv) (power circuit) (V) (operation circuit) Rated impulse withstand voltage Uimp (kv) (operation circuit) (A) according to IEC Rated voltage Utilisation category A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) 415 VAC AC-31 B VAC AC-32 B VAC AC-33 B (A) according to IEC Rated voltage Utilisation category A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) A/B (1) 415 VAC AC-20 A / AC-20 B 800/ / / / / / / VAC AC-21 A / AC-21 B 800/ / / /1600 -/2000 -/20 -/ VAC AC-22 A / AC-22 B 800/ / / /1600 -/2000 -/20 -/ VAC AC-23 A / AC-23 B 800/ / /12 12/12 -/1600 -/1600 -/ VAC AC-20 A / AC-20 B 800/ / / / / / / VAC AC-21 A / AC-21 B 800/ / / /1600 -/2000 -/20 -/ VAC AC-22 A / AC-22 B 630/ / / / VAC AC-23 A / AC-23 B 400/ / / /1000 Fuse protected short-circuit withstand as per IEC at 415 VAC Prospective short-circuit current ( rms) Associated fuse rating (A) x 800 Circuit breaker protected short-circuit withstand with any circuit breaker that ensures tripping in less than 0.3s (2) Rated short-time withstand current 0.3s I cw ( rms) Rated short-circuit withstand without protection Rated short-time withstand current 60ms I cw ( rms) as per IEC at 415 VAC Rated short-time withstand current 1s I cw ( rms) as per IEC at 415 VAC Rated peak withstand current ( peak) as per IEC at 415 VAC Connection Maximum Cu cable cross-section (mm²) 2 x x 240 Minimum Cu busbar cross-section (mm²) 2 x x 5 2 x x 5 2 x 60 x 5 2 x 80 x 5 Maximum Cu cable cross-section (mm²) 2 x x x x 185 Maximum Cu busbar width (mm) Tightening torque mini / maxi (Nm) 20/26 20/26 20/26 40/45 40/45 40/45 40/45 Switching time (Standard setting) I - II or II - I (s) I-0 or II-0 (s) Duration of "electrical blackout" I - II (s) Power supply min / max (VAC) 166/ / / / / / /332 Control supply power demand Power supply 230 VAC inrush / nominal (VA) - 460/ / / / / / /322 Power supply 230 VAC inrush / nominal (VA) - d, t, g, p 482/ / / / / / /344 Mechanical characteristics Durability (number of operating cycles) Weight 3/4 P (kg) 27.9/ / / /39.4.7/61.6.7/ /75.3 Weight d 3/4 P (kg) 28.5/ / / / / / /75.9 Weight r, t, g, p 3/4 P (kg) 29.0/ / / / / / /76.4 (1) Category with index A = frequent operation - Category with index B = infrequent operation. (2) Value for coordination with any circuit-breaker that ensures tripping in less than 0.3s. For coordination with specific circuit-breaker references, higher short-circuit current values are available. Please consult us. 2 x 100 x 10 2 x 100 x 10 2 x 100 x 10 4 Implementation of standard IEC / EN SOCOMEC
4 Product integration data in compliance with IEC / EN Below listed data is applicable to : Kn = 1 Kn = 0,87 Kn = 0,94 Kn = 0,81 M 319 A GB H catec_1_d catec_1_d W Fig. 1 Fig. 2 D Enclosure Kn = 1 Cabinet compartment Kn = 0,87 Kn = 0,94 Kn = 0,81 Dimensions of the Functional Unit Mounting Max Kn operational = 0,88 current, l e (A) Kn = 0,75 Kn = 0,68 H (mm) W (mm) D (mm) Enclosure Orientation 125 A 160 A 200 A 2 A 315 A 400 A 0 A 630 A Fig. 1/2 V (2) Fig. 1/2 H (2) Fig. 1/2 V (2) Fig. 1/2 H (2) Fig. 1 V (2) Min cross-section, mm 2 Insulated flat copper braids (mm 2 ) P/N 4516 xxxx Cable (mm 2 ) x 1 2 x 185 Cu busbar (mm 2 ) 2 x 30 x 5 2 x 40 x 5 Kn = 0,88 Kn = 0,75 Kn = 0,68 Dimensions of the Functional Unit Mounting Max operational current, l e (A) H (mm) W (mm) D (mm) Enclosure Orientation Fig. 1 V (2) (1) 23 (1) 27 (1) Fig. 1 H (2) (1) 2300 (1) 25 (1) Min cross-section, mm 2 Fig. 1/2 V (2) (1) 22 (1) 20 (1) Fig. 1/2 H (2) (1) 2200 (1) 20 (1) Cable (mm 2 ) 2 x x 1 4 x x x 1 8 x x 240 Cu busbar (mm 2 ) 2 x x 5 2 x 60 x 5 2 x 80 x 5 2 x 100 x 5 2 x 100 x 10 2 x 100 x 10 3 x 100 x 10 (1) Mounted with connection part (2) V : vertical mounting; H: horisontal mounting Heat dissipation Rating (A) Switch heat dissipation W/pole Maximum ambient temperature External 35 C Internal 60 C Heat dissipation Rating (A) Switch heat dissipation W/pole Recommanded tightening torque Maximum tightening torque M6: 4.5 N.m M6: 5.4 N.m M8: 8.3 N.m M8: 13 N.m M10: 20 N.m M10: 26 N.m M12: 40 N.m M12: 45 N.m C C - Min power connections length C - Min distance to first cable fixing support 400 mm 400 mm SOCOMEC - Implementation of standard IEC / EN
5 Circuit breaker protected short-circuit withstand* VL 160X VL 160 VL 2 VL 400 VL 630 VL 800 VL 1200 VL 1600 VF 12 VL 20 3VL1 3VL2 3VL3 3VL4 3VL5 3VL6 3VL7 3VL8 3VF7 3VF A A A A A T T T A T T T A T T T A T T T A T T T A T T T T T T A T T T T T T A T T T T T T T 75 T A T T T T T T T T T A T T T T T T T T T T 20 A T T T T T T T T T T 3200 A T T T T T T T T T T NS & NSX 160/2 NS & NSX 400 NS & NSX 630 (+800L) NS 1000 NS Masterpact 800/1000/12/1600 NT Masterpact NW Masterpact NW E NE N SX H L N H L N H L L N H L1 L1 H A T T T T A T T T T A T T T T A T T T T T T T A T T T T T T T A T T T T T T T A T T T T T T T T T T T A T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T T A T T T T T T T T T T T T T A T T T T T T T T T T T T T T 53 T A T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T 57 * - Subjected to MCCB s short circuit current liming curves reading precision and data. T- coordination possible up to the Max Icu value of the breaker Values are based on characteristics published by breaker manufacturers at the time of the publication. Socomec cannot be held responsible for any modifications of those characteristics or for nonperformance of circuit breakers 6 Implementation of standard IEC / EN SOCOMEC
6 Circuit breaker protected short-circuit withstand* (continued) TMAX T1 TMAX T2 TMAX T3 TMAX T4 TMAX T5 TMAX T6 TMAX T7 EMAX E2 EMAX E3 B C N N S H L N S N S H L V N S H L V N S H L S H L V E2L E3L DPX 125/ DPX DPX 2 ER ER 125 A T T T T T T T A T T T T T T T A T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T T T T T T T T T DPX 630 DPX 12/1600 DMX3 630/ / A T T T T A T T T T A T T T T A T T T T T T T A T T T T T T T A T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T A T T T T T T T T T T T T T T T T T 1800 A T T T T T T T T T T T T T T T T T 2000 A T T T T T T T T T T T T T T T T T T 20 A T T T T T T T T T T T T T T T T T T 3200 A T T T T T T T T T T T T T T T T T T x160 x2 h2 L SI h630 L SI (2-400 A) h630 L SI (630A) h1000 L SI h1600 HDA HHA HNA HNB HNC HND HED HND HED HNE HEE HNF HEF A T T A T T A T T A T T T T A T T T T A T T T T A T T T T T T A T T T T T T A T T T T T T T A T T T T T T T T T T T A T T T T T T T T T T T A T T T T T T T T T T T T T 1800 A T T T T T T T T T T T T T 2000 A T T T T T T T T T T T T T 20 A T T T T T T T T T T T T T 3200 A T T T T T T T T T T T T T * - Subjected to MCCB s short circuit current liming curves reading precision and data. T- coordination possible up to the Max Icu value of the breaker Values are based on characteristics published by breaker manufacturers at the time of the publication. Socomec cannot be held responsible for any modifications of those characteristics or for nonperformance of circuit breakers Non contractual document - Réalisation : Socomec DOC / 15 SOCOMEC - Implementation of standard IEC / EN
SIRCOVER. Manual changeover switches from 125 to 3200 A. Changeover switches. Function. Advantages. The solution for.
The solution for Changeover switches svr_099_b_1_cat > Manufacturing industry. > Power distribution. 3200 Strong points svr_059_a_1_cat > complete range. > Easy connections. > Stable positions. > mproved
Low voltage Direct Current Network. Compact NSX DC PV. Circuit breakers and switch disconnectors for solar application.
Low voltage Direct Current Network Compact NSX DC PV Circuit breakers and switch disconnectors for solar application Catalogue 2012 Compact NSX DC PV A complete DC offer for solar application from 80
FUSERBLOC. 20 to 1250 A Manual operation. 142 General Catalogue 2011-2012 SOCOMEC. Fuse combination switches
FUSERBLOC Fuse combination switches appli_8_a fuser_548_a cat fuser_59_a cat fuser_52_a cat 2 to 25 A Manual operation Function FUSERBLOC are manually operated multipolar fuse combination switches. They
Low Voltage Products. Switches Automatic Transfer Switches
Low Voltage Products Switches Automatic Transfer Switches Growing importance of a secure power supply Standby power is an integral part of many industrial and domestic electrical systems. High energy prices,
LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 - <= 440 V 65 A - 220 V AC coil
Product data sheet Characteristics LC1D65AM7 TeSys D contactor - 3P(3 NO) - AC-3 -
R.C.C.B. s two-pole LEXIC
87045 LIMOGES Cedex Telephone : (+33) 05 55 06 87 87 Fax : (+ 33) 05 55 06 88 88 R.C.C.B. s two-pole LEXIC 089 06/09/10/11/12/15/16/17/18/ 27/28/29/30/35, CONTENTS PAGES 1. Electrical and mechanical characteristics...
Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
NF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101433D0201 28/03/11 NF71E-.. / NFZ71E-.. Contactor Relays AC / DC Operated - with Screw Terminals NF(Z) contactor relays are used for switching auxiliary and control circuits.
Safety automation solutions
Operating principle, characteristics Preventa safety s types XPS AV,, For and switch monitoring Operating principle Safety s XPS AV, and are used for monitoring circuits conforming to standards EN/ISO
Breaking and protection devices
Breaking and protection devices 05 POWER GUIDE 2009 / BOOK 05 INTRO The purpose of selecting a protection device is to perform two essential functions: to protect people and to protect trunking, while
AF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101403D0201 24/03/11 AF09-30-22-.. / AF09Z-30-22-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals AF09(Z) contactors are used for controlling power circuits
AUTOMATIC TRANSFER SWITCH. Changeover Type from 250A to 2500A
AUTOMATIC TRANSFER SWITCH Changeover Type from 250A to 2500A Table of Contents Preamble 1.1 Theoretical base 1.2 Selection the size of automatic transfer switch 1.3 Automatic transfer switch components
E-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
LV MCC LOW VOLTAGE SWITCHGEAR MOTOR CONTROL CENTRE PRODUCT GUIDE
LV MCC LOW VOLTAGE SWITCHGEAR MOTOR CONTROL CENTRE PRODUCT GUIDE 380/415/690 Volt AC 50/65/80/100 ka 1. Product Guide Low Voltage Motor Control Centre CONTSTRUCTION Continuous "poured in place" gasket
Application Switchgear for industrial and commercial applications. U e V AC 230/400. 48 (per pole)
Overcurrentswitch,6A,2p,D-Char,AC Partno. FAZ-D6/2 Articleno. 278777 CatalogNo. FAZ-D6/2 Similar to illustration Deliveryprogramme Basic function Miniature circuit breakers Pole 2 pole Tripping characteristic
SENTRON Switching and Protection Devices Air Circuit Breakers
Siemens AG 9 SENTRON Switching and rotection Devices Air Circuit reakers 5 5/ Introduction 3WL Air Circuit reakers 3WL Air Circuit reakers/ Non-Automatic Air Circuit reakers up to 63 A (AC) 5/6 General
MEDIUM VOLTAGE CE-BF SWITCHBOARDS. UP TO 40.5 kv. CE - BF - C - en - REV.00 2012.4
CE - BF - C - en - REV.00 2012.4 APPLICATION CE-BF Switchbords up to 40.5 kv are designed for use in public and industrial distribution system up to 40,5KV for the operation and protection of lines, transformers,
METAL-CLAD AND METAL-ENCLOSED SWITCHGEAR 3.6KV~40.5KV. tgood.com. Energy. Fast.
METAL-CLAD AND METAL-ENCLOSED SWITCHGEAR 3.6KV~40.5KV tgood.com Energy. Fast. TGOOD produces over 5000 switchgear units annually for projects around the globe PRODUCT OVERVIEW Integral substation component
Emergency stop As an emergency switching off/emergency stop device. Standards According to IEC/EN 60204-1, VDE 0113 Part 1
MainswitchSurfacemounting Partno. P3-63/I4/SVB Articleno. 207343 CatalogNo. SP3-063-I4CRQ IP65 Deliveryprogramme Product range Switch-disconnectors Basic function Main switches Maintenance switches Manual
Single-phase (220...240 V) voltage monitoring: Undervoltage Overvoltage Window mode (overvoltage + undervoltage) Voltage fault memory selectable
Features 70.11 70.31 70.41 Electronic voltage monitoring relays for single and three-phase applications Multifunctional types, providing the flexibility of monitoring Undervoltage, Overvoltage, Window
Single and three phase modular Automatic Transfer Switch from 40 to 160 A
NEW SINGLE PHASE Single and three phase modular Automatic Transfer Switch from 40 to 160 A SWITCH TO INNOVATION SOCOMEC: intelligent changeover systems As a worldwide leading company in changeover power
Securing your electrical installations Prisma,
Securing your electrical installations Prisma, an optimised solution for type tested low voltage switchboards up to 3200 A Table of contents Developing installation safety 4 Prisma P * Electrical switchboards
The complete range of consumer switchboards and switchgear
Power Distribution The complete range of consumer switchboards and switchgear www.nhp.com.au/mod6 The MOD6 range of consumer switchboards and switchgear is specifically designed for domestic and commercial
SURGE PROTECTIVE DEVICES
SURGE PROTECTIVE DEVICES 1. INTRODUCTION In order to ensure safety of people, protection of equipment and, to a certain extent, continuity of supply, insulation co-ordination aims at reducing the likelihood
Tmax MCCBs. Molded case circuit breakers. Tmax
Molded case circuit breakers Introduction ABB is once again demonstrating its commitment to new product development and its superiority in product performance. Never before has the industry seen such high
Breakers and Switches. Switches Switch-disconnectors OT, OETL, OTDC and OTM
Breakers and Switches Switches Switch-disconnectors OT, OETL, OTDC and OTM Switch-disconnectors OT 16...2500, OETL 3150, OTDC16...32 and OTM160...2500 Contents 4 Product overview, features 8 Technical
Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592. * see variants. Applications.
Safety Technique SAFEMASTER Emergency Stop Module BG 5924, IP 5924 Your Advantages For safety application up to PL e / Cat. 4 e.g. SIL 3 Manual or automatic start 0225592 BG 5924 IP 5924 Product Description
Electronic overload relay EF65, EF96 and EF146
Data sheet Electronic overload relay EF65, EF96 and EF146 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays.
Thermistor motor protection
Thermistor motor protection CM-E Range Thermistor motor protection Thermistor motor protection relays Benefits and advantages Selection table Operating principle and fields of application for thermistor
RM17TE 183...528 V AC. Main. Product or component type. Product specific application. Relay monitored parameters 250 V DC 5 A DC
Characteristics multifunction control relay RM17-TE - range 183..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
White paper. ABB solutions for switching and protection of low speed wind turbines
White paper ABB solutions for switching and protection of low speed wind turbines ABB solutions for switching and protection of low speed wind turbines Index 1 Introduction...2 2 Full converter configuration...4
E-STOP relays, safety gate monitors
Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Unit features Gertemerkmale Positive-guided relay outputs: 2 safety contacts (N/O), instantaneous Connection
ABB i-bus KNX Fan Coil Actuator, MDRC FCA/S 1.1M, 2CDG 110 084 R0011
, 2CDG 110 084 R0011 2CDC 071 112 F0008 The Fan Coil Actuator is a modular installation device (MDRC) in pro M design. It is intended for installation in the distribution board on 35 mm mounting rails.
VEO. V4PF480Y/277VSYTK02 Art.Nr.: 2104200. V4PF480Y/277VSYTK02P Art.Nr.: 2104210 TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Temperature monitoring (PTC) Supply voltage 208-480 V AC Supply circuit = measuring circuit 2 change-over contacts Width 45 mm Control
Redundancy Module QUINT-DIODE/40
Redundancy Module QUT DIODE provides: 00% decoupling of power supplies connected in parallel Can be installed in potentially explosive areas Load currents up to 60 A supported Easy assembly by snapping
Technical catalogue. Modular DIN rail components Installation contactors
Technical catalogue Modular DIN rail components Installation contactors Installation Contactors Overview... ESB Installation Contactors 0 A / AC-/AC-7a ESB0...4 4 A / AC-/AC-7a ESB4...5 40 A / AC-/AC-7a
PNOZsigma - Base units
PNOZsigma - Base units Register Login Sensors Control and Communication Electronic monitoring relays Safety Relays PNOZ X PNOZsigma PNOZelog PNOZmulti PNOZpower Configurable control systems Programmable
Manual motor starter MS116
Data sheet Manual motor starter MS116 Manual motor starters are electromechanical devices for motor and circuit protection. These devices offer local motor disconnect means, manual ON/ OFF control, and
Technical catalog - Edition 2015. SACE Tmax PV Adaptability, versatility and complete freedom continue
Technical catalog - Edition 205 SCE Tmax PV daptability, versatility and complete freedom continue SCE Tmax PV automatic molded case circuit-breakers and molded case switch-disconnectors The Tmax PV line
Mini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection
Technical Data Mini Circuit Breakers, Fuse Blocks, and Electronic Circuit Protection Topic Page 1489-M Miniature Circuit Breakers 2 1492-SP Supplementary Protectors 15 1492-D Circuit Breakers 27 188 Regional
Catalog. Modular DIN rail components Installation contactors
Catalog Modular DIN rail components Installation contactors 0 CDC00C00 Installation contactors Benefits and features Overview Ordering details ESB installation contactors ESB0 ESB ESB0 ESB 7 EN installation
Electronic overload relay EF19 and EF45
Data sheet Electronic overload relay EF19 and EF45 Electronic overload relays offer reliable protection in case of overload and phase-failure. They are the alternative to thermal overload relays. Motor
Fixed - Over/Under voltage limits, (0.75...1.2) U N respectivity Link selectable - 5 min or 10 min delay. Fixed limits
Features 71.11.8.230.0010 71.11.8.230.1010 1 - Phase 230 V Over & Under voltage monitoring relays 71.11.8.230.0010 - Fixed Over & Under voltage detection - Link selectable 5 or 10 minute lock-out delay
BETA Switching. Switching Devices. 5TT5 8 Insta contactors, AC technology. Overview
BETA Switching Siemens AG 200 5TT5 Insta contactors, AC technology Overview The 5TT5 Insta contactors are equipped with an AC magnetic system and are ideal for use under harsh conditions. The auxiliary
Type: DILM32 10(24V50HZ) Article No.: 277247
Type: DILM32 10(24V50HZ) Article No.: 277247 Ordering information Rated operational current AC 3 400 V I e A 32 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase motors,
ELEKTROTEHNI KO PODJETJE Leskoπkova cesta 12, 1000 Ljubljana, SLOVENIA
MRO Modularne Razdelilne Omare d.o.o. ELEKTROTEHNI KO PODJETJE Leskoπkova cesta 2, 000 Ljubljana, LOVENIA MC GENERAL When to use? MC - modular switchgear cabinets are type-tested, factory built switchgears,
RCA Remote Control ic60 Circuit Breakers Reference Manual
9M01EN 01/2011 RC Remote Control ic60 Circuit reakers Reference Manual 01/2011 9M01EN www.schneider-electric.com The information provided in this documentation contains general descriptions and/or technical
Submit shop drawings for equipment provided under this section Shop drawings shall indicate:
Section 16435 - SWITCHBOARDS Introduction Part 1 - General Reference The work under this section is subject to requirements of the Contract Documents including the General Conditions, Supplementary Conditions,
RM4TG20 three-phase network control relay RM4-T - range 200..500 V
Characteristics three-phase network control relay RM4-T - range 200..500 V Complementary [Us] rated supply voltage Output contacts Setting accuracy of time delay Delay at power up Measuring cycle Marking
Medium Voltage Products. ZN1 12 kv arc-proof air-insulated switchgear for primary distribution
Medium Voltage Products ZN1 12 kv arc-proof air-insulated switchgear for primary distribution ZN1 an innovative switchgear for power distribution requirements ABB ZN1 primary distribution switchgear is
Type: DILM50(230V50HZ,240V60HZ) Article No.: 277830
Type: DILM50(230V50HZ,240V60HZ) Article No.: 277830 Ordering information Rated operational current AC 3 400 V I e A 50 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase
Type-Tested Power Distribution Board 8PT with Rear Busbars. sivacon
Type-Tested Power Distribution Board 8PT with Rear Busbars sivacon The Obvious Solution for Global Challenges SIVACON Type-testing is one of today s important issues for low-voltage technology and will
ADM1TE 5/30A DIN rail single phase two wire energy meter
ADMTE 5/30A DIN rail single phase two wire energy meter. Safety instruction.2 Foreword.3 Performance criteria.4 Specifications.5 Basic errors.6 Description.7 Dimensions.8 Installation.9 Operating.0 Troubleshooting.
Voltage Regulator SPAU 341 C. Product Guide
Issued: July 1998 Status: Updated Version: D/25.04.2006 Data subject to change without notice Features Comprehensive voltage regulation for power transformers with on-load tapchangers in distribution substations
34 Series - Slim electromechanical PCB relays 6 A. Features SERIES 34.51
34 Series - Slim electromechanical PCB relays 6 34 SERIES Features 34.51 Ultra-slim 1 Pole - 6 relay Printed circuit mount - direct or via PCB socket 35 mm rail mount - via screw, screwless or push-in
DRM75A 230V 20/100A DIN rail single phase two wire energy meter
DRM75A 230V 20/100A DIN rail single phase two wire energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Description 1.7 Dimensions 1.8 Installation
Type: DILM9 10(24VDC) Article No.: 276705
Type: DILM9 10(24VDC) Article No.: 276705 Ordering information Rated operational current AC 3 400 V I e A 9 Max. rating for three phase motors, 50 60 Hz AC 3 230 V Max. rating for three phase motors, 50
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 - 16 A 38 SERIES Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical
Molded Case Circuit Breaker Specifications Bulletin Number 140U-D
Technical Data Molded Case Circuit Breaker Specifications Bulletin Number 140U-D Topic Page Product Line Overview 2 Specifications 3 Trip Curves 4 Approximate Dimensions 6 Additional Resources These documents
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A
38 Series - Relay interface modules 0.1-2 - 3-5 - 6-8 A Common features Instant ejection of relay by plastic retaining clip Integral coil indication and protection circuit EMR Electromechanical Relays
Micro Contactors. Micro Contactor Relays. Micro Contactors With Solder Pins. Coil voltages. Micro Reversing Contactor. Technical Data.
Micro Contactors Micro Contactor Relays 0 Micro Contactors Micro Contactors With Solder Pins Coil voltages Micro Reversing Contactor 3 Technical Data 4 Dimensions 8 9 Micro Contactor Relays 4pole C Operated
Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-AHD.12 OFF-delayed with 1 c/o (SPDT) contact The CT-AHD.12 is an electronic time relay with OFF-delay. It is from the CT-D range. With their MDRC profile and a width of only
Outdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points
Outdoor 33.6W Dual Port Passive Power-over-Ethernet Midspan For External Security Cameras and Wireless Access Points Features SELV Compliant No Detection Passive Injector Gigabit Compatible Full Protection
Type: EASY719 DC RC Article No.: 274119. Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC. Description
Type: EASY719 DC RC Article.: 274119 Ordering information Relay outputs Quantity 6 Power supply V DC 24 V DC Description 12 digital inputs (4 inputs available as analog inputs) 6 relay outputs LCD display
MasterINTERFACE 39 Series - Relay interface modules
MasterINTERFACE 39 Series - Relay interface modules Common features Space saving 6.2 mm wide Connections for 16-way jumper link Integral coil indication and protection circuit Secure retention and easy
Type: DILM115(RAC240) Article No.: 239548 Sales text Contactor,55kW/400V,AC operated. Ordering information
Type: DILM115(RAC240) Article No.: 239548 Sales text Contactor,55kW/400V,AC operated Ordering information Connection technique Description Description Rated operational current Screw terminals 3 pole AC
DEK-REL- 24/1/SEN. Extract from the online catalog. Order No.: 2964050
Extract from the online catalog DEK-REL- 24/1/SEN Order No.: 2964050 Relay terminal block for sensor, with soldered-in miniature relays, contact (AgNi+Au): small to medium loads, 1 N/O contact, input voltage
ELECTROMAGNETIC DISC BRAKES
ELECTROMAGNETIC DISC BRAKES TYPE 66E 15/30 52.121 Hand release Lining wear adjustment Torque adjustment 4 holes ø13 DISC SIZE Ø A Braking torque Nm Regulated from (40-100%) Reaction on the shaft N Control
Three-phase monitoring relay CM-PFE
Data sheet Three-phase monitoring relay CM-PFE The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251 005 S0012 Characteristics
49 Series - Relay interface modules 8-10 - 16 A. Features
Features 1 & 2 Pole relay interface modules 5 µm Gold plate contacts for low level switching capability 49.31-50x0-1 Pole 10 A (screw terminal) 49.52-50x0-2 Pole 8 A (screw terminal) 49.72-50x0-2 Pole
48.12. 2 pole, 8 A Safety relay. Screw terminal. 35 mm rail (EN 60715) mounting. 2 CO (DPDT) 8/15 250/400 2,000 500 0.37 8/0.65/0.
48 Series - Relay interface modules 8 A Features 48.12 2 Pole Safety relay interface modules, 15.8 mm wide 48.12-2 Pole 8 A (screw terminal) DC sensitive coils Relay with forcibly guided contacts according
48 SERIES Relay interface modules 10 A
48 Relay interface modules 10 A 1 CO relay interface modules, mm wide Ideal interface for PLC and electronic systems Type 48.P3 1 CO 10 A s Type 48.31 1 CO 10 A s AC coils or DC sensitive coils Supply
How To Operate A Gec Transfer Switch Open Transition 40 2000 Amp Power Supply
GTEC Transfer switch open transition 40 2000 amp Description GTEC transfer switches combine reliability and flexibility in a small, economical package for transferring loads between a utility and a generator
UniGear ZS1. Medium voltage, arc proof, air insulated switchgear for primary distribution
UniGear ZS1 Medium voltage, arc proof, air insulated switchgear for primary distribution UniGear ZS1: an innovative solution for all installation requirements ABB UniGear is medium voltage metal-clad,
NATUS NES / NES-H Draw-out Type Medium Voltage Switchgear Systems. Safe energy distribution that meets the highest industrial requirements
NATUS NES / NES-H Draw-out Type Medium Voltage Switchgear Systems Safe energy distribution that meets the highest industrial requirements NATUS switchgear systems your advantages minimal use of insulant
Power Supply Unit, Primary Switched, Narrow Design MINI-PS-12-24DC/24DC/1
Power Supply Unit, Primary Switched, Narrow Design MINI POWER provides: Extra narrow design with widths of 22.5 mm, 45 mm, and 67.5 mm (0.886, 1.772, and 2.657 in.) Global use due to a wide-range input
Technical Manual Functional Description for S800-RSU-H / S800W-RSU 2CCC413022M0205. 8201 Schaffhausen 1 / 10
ABB ABB Schweiz AG Technical Manual Functional Description for S800-RSU-H / S800W-RSU 2CCC413022M0205 09.04.2014 Page: 8201 Schaffhausen 1 / 10 Please use also the assembly instruction S800-RSU-H Remote
0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.8 U N /0.5 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N 0.2 U N /0.1 U N
55 Series - General purpose relays 7-10 A Features 55.12 55.13 55.14 Printed circuit mount, general purpose 2, 3 & 4 Pole relays 55.12-2 Pole 10 A 55.13-3 Pole 10 A 55.14-4 Pole 7 A AC coils & DC coils
Safety technique. Emergency stop module BO 5988 safemaster
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
IEC 60439 >>> IEC 61439 GUIDE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES
xl 3 configurable assemblies IEC 60439 >>> IEC 61439 GUIDE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES XL 3 configurable assemblies guide to migration from IEC 60439 to IEC 61439
Catalog January. Heavy industrial power applications Motor contactors and starters
Catalog January Heavy industrial power applications Motor contactors and starters 2006 General contents 0 Heavy Industrial Power Applications Motor Contactors and Starters 1 Contactors and Starters, Type
Uncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M
Uncompromising safety and comfort The next generation of miniature circuit breakers MCB S 200/S 200 M The details make the difference MCB S 200/S 200 M A range designed to ensure efficiency and protection
Technicaldata General
Currenttransformer-operatedoverloadrelay,60-90A,1N/O+1N/C Partno. ZW7-90 Articleno. 002618 CatalogNo. XTOT090C3S Deliveryprogramme Product range ZW7 current transformer-operated overload relays Description
RM35UA13MW. range 15..600 V. Main. Product or component type. Relay monitored parameters
Characteristics multifunction voltage control relay RM35-U - range 15..600 V Complementary Reset time Maximum switching voltage [Us] rated supply voltage Supply voltage limits Power consumption in W Main
Catalogue May 2015. EasyLine XLP Fuse Switch Disconnector 1-2-3-4 pole
Catalogue May 2015 EasyLine XLP Fuse Switch Disconnector 1-2-3-4 pole Contents Introduction 1 Overview 1-pole 2 Overview 2-pole 3 Overview 3-pole 4 Overview 4-pole 5 Electronic Fuse Monitoring 6 Busbar
Bulletin 150 Smart Motor Controllers SMC-3 Smart Motor Controller
Overview/Modes of Operation Bulletin 150 Smart Motor Controller The SMC-3 is a compact, simple to use, solid-state motor controller designed to operate 3-phase motors. It features a built-in overload relay
E-STOP relays, safety gate monitors
Unit features Safety features gang engertebild ][Bildunterschrift_NOT_Sch.tuer_Licht Safety relay for monitoring E-STOP pushbuttons, safety gates and light beam devices Approvals Gertemerkmale Positive-guided
Breakers and Switches. Switches Change-over, bypass and transfer switches
Breakers and Switches Switches Change-over, bypass and transfer switches Change-over, bypass and transfer switches Product overview, features Product overview 4 Features 6 Technical data Manual / motorized
225-230T-05-S2. Rotary drive without spring return. Technical data sheet. Description. Technical data. Actuators
Actuators Technical data sheet 225-230T-05-S2 Rotary drive without spring return Description Actuator for adjusting air dampers of 90 angle of rotation to be used in HVAC installations. Torque Motor 5
Circuit Breakers and Switchgear. Thomas Greer Director of Engineering TLG Services
Circuit Breakers and Switchgear Thomas Greer Director of Engineering TLG Services Presentation Outline Switchgear Definition Overcurrent Protection Devices Circuit Breaker Trip Curves and Coordination
MNS is Switchgear System Technical Overview
Switchgear System Technical Overview Innovative Design ABB s innovative MNS is concept combines the long term experience, energy efficiency, grid reliability and industrial productivity of the well-known
Switching Devices. 8/2 Introduction. 8/5 5TE8 control switches. 8/8 5TE4 pushbuttons. 8/11 5TE5 light indicators. 8/13 5TE On/Off switches
Siemens AG 2014 Switching Devices /2 Introduction /5 5TE control switches / 5TE4 pushbuttons /11 5TE5 light indicators /13 5TE On/Off switches /20 5TE DC isolators /22 5ST busbars for modular installation
CompactLogix Power Supplies Specifications
Technical Data CompactLogix Power Supplies Specifications 1768 CompactLogix Power Supplies Catalog Numbers 1768-PA3, 1768-PB3 1769 Compact I/O Power Supplies Catalog Numbers 1769-PA2, 1769-PB2, 1769-PA4,
E-STOP relays, safety gate monitors
Unit features Safety features Gertebild ][Bildunterschrift Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Gertemerkmale Positive-guided relay outputs: 3 safety contacts (N/O),
The Intelligent AX1 Switchgear for Medium Voltage
The Intelligent AX1 Switchgear for Medium Voltage Leif Lundin, Manager of Research and Development, Division Medium Voltage and Compact Substations, ABB Distribution, Sweden Abstract The newly launched
Relés e Contatores de Estado Sólido SIRIUS
Relés e Contatores de Estado Sólido SIRIUS Coletânea de dados técnicos ( product data sheet ) Agosto/212 SSR - 3RF21 22,5 mm Ponto Zero SSR - 3RF2 45 mm Ponto Zero SSR - 3RF22 45 mm Ponto Zero Trifásico
Mini Motor Contactor J7KNA Main contactor Accessories Approved Standards Standard Guide No (US,C) Ordering Information tage Model Number Legend gear
Mini Motor Contactor J7KNA ) Main contactor AC & DC operated Integrated auxiliary contacts Screw fixing and snap fitting (35 mm DIN-rail) Range from 4 to 5.5 (AC 3, 380/415V) 4 -main pole version (4 AC
ABB i-bus KNX Switch Actuator, x-fold, 16/20 A, MDRC SA/S x.16.6.1, 2CDG 110 1xx R0011
, 2CDG 110 1xx R0011 SA/S 8.16.6.1 2CDC 071 006 S0010 The 16/20 A Switch actuators are modular installation devices in Pro M Design for installation in the distribution board. The devices are especially
Power consuption Motor (Motion) Power consuption Standby (end position) 1,0 W. Position feedback - Switching point 0...95
Actuators Technical data sheet 227S-230-05-S1 Rotary drive without spring return Description Actuator for adjusting air dampers of 90 angle of rotation to be used in HVAC installations. Torque Motor 5
D-Line Contactors, Overload Relays and Accessories
D-Line Contactors, Overload Relays and Accessories Class 850 CONTENTS Description......................................................Page General Information...............................................