1.2 Xenon Headlamps Models 202, 208, 210

Transcription

1 Eletrial Test Program Test Test sope Test onnetion Test ondition Nominal value Possible ause/remedy 1.0 eft lo beam Xenon headlamp (E1e8) Voltage at illumination ontrol module () Models 208, 210 Remove fuse ( ) and hek voltage using rest urrent maintenane unit. o beam: ON (), O Voltage and amperage at illumination ontrol module () Remove fuse ( ). Revie Figure 1 and attah ables as shon. A brief amp flo is noted only hen first sithing on: Indutive pikup reading hen sithing on o beam: ON After approx. 30 seonds amps (I), then alulate attage (P). Xenon headlamp ontrol module (E1n1) ith Xenon module (E1n2) 2). 1) To prevent damge to ne installed Xenon lamps (D2R, 35W), be ertain to hek system output (atts) output prior to lamp installation. 2) Replae omplete headlamp unit as neessary. b Diagnosti Manual Body and Aessories 06/ E 23/1

2 Eletrial Test Program Test Test sope Test onnetion Test ondition Nominal value Possible ause/remedy 2.0 Right lo beam Xenon headlamp (E2e8) Voltage at illumination ontrol module () Models 208, 210 Remove fuse ( ) and hek voltage using rest urrent maintenane unit. o beam: ON (), O Voltage and amperage at illumination ontrol module () Remove fuse ( ). Revie Figure 1 and attah ables as shon. A brief amp flo is noted only hen first sithing on: Indutive pikup reading hen sithing on o beam: ON After approx. 30 seonds amps (I), then alulate attage (P). Xenon headlamp ontrol module (E2n1) ith Xenon module (E2n2) 2). 1) To prevent damge to ne installed Xenon lamps (D2R, 35W), be ertain to hek system output (atts) output prior to lamp installation. 2) Replae omplete headlamp unit as neessary. b Diagnosti Manual Body and Aessories 06/ E 23/2

3 Eletrial Test Program Test Test sope Test onnetion Test ondition Nominal value Possible ause/remedy 3.0 eft lo beam Xenon headlamp (E1e8) Voltage at fuse and relay box (). Remove fuse () and hek voltage using rest urrent maintenane unit. o beam: ON O 1.1 Model Voltage and amperage at fuse and relay box (). Remove fuse (). Revie Figure 1 and attah ables as shon. A brief amp flo is noted only hen first sithing on: Indutive pikup reading hen sithing on o beam: ON After approx. 30 seonds amps (I), then alulate attage (P). Xenon headlamp ontrol module (E1n1) ith Xenon module (E1n2) 2). 1) To prevent damge to ne installed Xenon lamps (D2R, 35W), be ertain to hek system output (atts) output prior to lamp installation. 2) Replae omplete headlamp unit as neessary. b Diagnosti Manual Body and Aessories 06/ E 23/3

4 Eletrial Test Program Test Test sope Test onnetion Test ondition Nominal value Possible ause/remedy 4.0 Right lo beam Xenon headlamp (E2e8) Voltage at Fuse and relay box (). Remove fuse () and hek voltage using rest urrent maintenane unit. o beam: ON (), O 2.1 Model Voltage and amperage at fuse and relay box (). Remove fuse ( ). Revie Figure 1 and attah ables as shon. A brief amp flo is noted only hen first sithing on: Indutive pikup reading hen sithing on o beam: ON After approx. 30 seonds amps (I), then alulate attage (P). Xenon headlamp ontrol module (E2n1) ith Xenon module (E2n2) 2). 1) To prevent damge to ne installed Xenon lamps (D2R, 35W), be ertain to hek system output (atts) output prior to lamp installation. 2) Replae omplete headlamp unit as neessary. b Diagnosti Manual Body and Aessories 06/ E 23/4

5 Eletrial Test Program Test Connetion diagram Amperage and Voltage Measurement An indutive pikup must be used during amperage measurement, sine high amps ill be present hen the Xenon headlamps are first sithed on. Figure 1 1 Multimeter (voltage measurement) 2 Multimeter (amperage measurement) 3 Indutive pikup 4 Fused test able 5 Measurement test able 6 Adapter test able 7 Rest urrent maintenane unit P b Diagnosti Manual Body and Aessories 06/ E 23/5