Earthing systems. System overview from page 226. Principles from page 228. Products from page 230 TBS
|
|
- Harold Crawford
- 7 years ago
- Views:
Transcription
1 good earthing system in accordance with DIN VDE (IEC ) is the basis of a good lightning protection system. The lightning current safely deflected by the interception and arrester system is routed to the ground. The equipotential bonding performs an additional task between the arresters and as an equipotential bonding controller in passable areas. 224 TS
2 System overview from page 226 Principles from page 228 Products from page 230 TS 225
3 System overview Potential equalisation systems from P.166 Earth fixing point from P.240 Conducter material from P. 228 Connection termin 226 TS
4 Corrosionproofing band from P.243 al from P. 239 TS 227
5 Planning an earthing system The earthing system is part of the external lightning protection system, which routes the lightning current into the ground where it is to be distributed. The key criteria for an even lightning current distribution without dangerous surges occurring are form and dimensions. In accordance with DIN VDE 0185 Part 3 (IEC 305-3) Section 4.4.1, a lower earthing resistance < 10 is generally recoended. n earthing system can be constructed from one of the three arrangements described below. It is possible to connect different earthing arrangements, although the risk of corrosion must be taken into account. Important notice: earthing systems must be connected to the equipotential bonding. Deep earther deep earther is an earther, which is generally integrated vertically and deep into the ground. The simplest solution for retrofitting a lightning protection system. Ring earther ring earther is a surface earther, which if possible is installed as a closed ring at a distance of 1.0 m and 0.5 m deep into the ground around the external foundation of the building. The better, although more expensive, solution for retrofitting a lightning protection system. Foundation earther foundation earther (acc. to T 1974 specified for new buildings) is embedded into the concrete foundation of a building. It then also acts as a lightning protection earther, if the lugs required for connecting the arresters protrude from the foundation. Deep earther deep earther (arrangement ) is an earther that is generally integrated vertically and deep into the ground. s single earthers, a deep earther of 9.0 m in length is recoended. This should be installed at a distance of 1.0 m from the foundation of the building. s a minimum dimension (acc. to DIN VDE 0185 Part 3 Fig. 2) a length of 2.5 m for vertical installation and 5 m for horizontal installation apply for earthers for lightning protection classes III and IV. The required earther lengths may be split into several lengths connected in parallel. Depending on the soil conditions, deep earthers can be driven into the ground by hand or by using suitable electric, petrol or pneumatic haers. The following materials can be used: Rods from galvanised steel Ø 20 Rods from stainless steel Ø 20 Pipes from galvanised steel Ø 25 (2 wall thickness) Flat conductors from galvanised steel 30 x 3.5 Flat conductors from stainless steel 30 x 3.5 In potentially corrosive areas, stainless steel must always be used. Detachable s in the ground must be protected against corrosion (plastic corrosion protection strip). Note: For deep earthers, a length of 9.0 m is recoended. Cross-connectors from page 237 Corrosion protection strips from page 243 Round conductors from page 186 ttaching clips from page 242 Earthing rods from page 232 ll deep earthers must be connected with a ring earther inside or outside of the building and with a lead to the PS. 1 m Striking points from page TS
6 Ring earthers (surface earthers) Outside the building, at least 80% of the ring earther s overall length must be in contact with the ground. It must be installed as a closed ring at a distance of 1.0 m and a depth of 0.5 m around the external foundation of the building. ring earther is an earther according to arrangement type. 1 m The following materials can be used: Flat conductor galvanised steel 30 x 3.5 Flat conductor stainless steel 30 x 3.5 Round conductor copper, Ø 8 Round conductor Ø 10, galvanised steel Round conductor Ø 10, stainless steel In potentially corrosive areas, stainless steel (V4) must always be used. Detachable s in the ground must be protected against corrosion (plastic corrosion protection strip). Flat conductor from page 186 Cross-connectors from page 237 Round conductors from page 186 Corrosion protection strips from page 243 Foundation earthers foundation earther is an earther that is embedded into the concrete foundation of a building. It acts as a lightning protection earther if the lugs required for connecting the arresters protrude from the foundation. The steel strip is to be attached / connected to reinforcements at a distance of approx. 3 m. DIN forms the basis for constructing external lightning protection systems. Wedge connectors must not be inserted into the ground. In order to achieve a clean insertion, the use of strip holders is recoended for the installation of foundation earthers. The holders must be inserted at a distance of approx. 2 m. The following materials, among others, can be used for foundation earthers: Flat conductor galvanised steel 30 x 3.5 Flat conductor stainless steel 30 x 3.5 Round conductor copper, Ø 8 Round conductor Ø 10, galvanised steel Round conductor Ø 10, stainless steel In potentially corrosive areas, stainless steel should always be used at the entry and exit points on the concrete. Flat conductors from page 186 Diagonal terminals from page x 20 m Spacers from page 240 Flat conductors from page 186 TS 229
7 Flat conductor, steel galvanised Conduction material x H Normal ring /% m ca. m m borders ST / FT 5052 St FT 25 x , St FT 25 x , St FT 30 x , St FT 40 x , St FT 40 x , St FT 30 x , St FT 30 x 3, , St FT 30 x 3,5 FIX , H 5052: Flat conductor/strip steel in rings Zinc layer: 225 g/m² (approx. 30 µm) pplication: foundation earthing, not laid in ground. Flat conductor, steel galvanised for ground Conduction material x H Normal ring /% m ca. m m borders ST / FT 5052/ DIN St FT 20 x 2, , / DIN St FT 30 x 3, , / DIN St FT 30 x 3,5 FIX , / DIN St FT 30 x 3,5 FIX , / DIN St FT 30 x 4 FIX , / DIN St FT 40 x 5 FIX , H 5052: Flat conductor/strip steel in rings (conforms to DIN EN ) DIN Zinc layer: 500 g/m² (approx. 70 µm) rea of application: Lightning protection and earthing Flat conductors, stainless steel Conduction material x H Normal ring /% m ca. m m borders V V V2 30 x 3, , V V V4 30 x 3, , H 5052V: Flat conductor/strip steel in rings Conforms to the requirements according to DIN V VDE V , Table 8 From stainless steel, for use in potentially corrosive areas From stainless steel V4, for use in ground rea of application: Lightning protection and earthing Flat conductor, copper Conduction material x H Normal ring /% m FL20/Cu Cu 20 x 2,5 ca. m m borders Cu , s according to DEL notation; see material references. FL20/Cu: Flat conductor/strip steel in coils (to DIN EN ) H Version: E-Cu S7 F24 soft rea of application: Lightning protection and earthing Round conductor, aluminium Nominal size Ø Normal ring Crosssection ca. m ² m borders l RD 8/LU l (± 7,5 m) , RD 8/LU-T l (± 7,5 m) , RD 10/LU l (± 4,5 m) , T Tordier quality RD...-LU: Round conductor Conforms to the requirements according to VDE V , (IEC 62305) luminium RD 8/LU: halbhart (E-lMgSi0.5 to DIN 48801) RD 8/LU-T: tordierbar (E-lMgSi0.5 to DIN 48801) RD 10/LU: Rein-luminium(E-l to DIN 48801) /% m Conduction material D 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 230 TS
8 Conduction material D Conduction material D Conduction material D Conduction material RD...: Round cable (to DIN EN ) Nominal size Ø Normal ring ca. m ² m borders ST / FT RD 8 St (± 2 m) , RD 10 St (± 2m) , Fulfils the requirements to VDE (IEC 62305) RD 10 can also be used in earth Galvanised steel Zinc coating: 50 µm average value (approx. 350 g/m²) Nominal size Ø Normal ring Round conductor, steel galvanised ca. m ² m borders Cu RD 8/Cu Cu (± 2 m) , RD 10/Cu Cu (± 2 m) , RD...Cu: Round conductor Conforms to the requirements according to VDE V , (IEC 62305) Nominal size Ø Normal ring Crosssection Crosssection Crosssection /% m Round conductor, copper ca. m ² m borders V2 RD 8/V2 V (± 2,5 m) , RD 10/V2 V (± 2,5 m) , V4 RD 8/V4 V (± 2,5 m) , RD 10/V4 V (± 2,5 m) , RD...-V: Round conductor Conforms to the requirements according to VDE V , (IEC 62305) From stainless steel V4, for use in ground RD 8/PVC RD...: Round conductor Nominal size Ø 8/11 /% m Round conductor, stainless steel /% m Round conductor with PVC sheathing m borders l l , /% m Conforms to the requirements according to VDE V , (IEC 62305) With PVC sheathing Normal ring Crosssection /% m RD 10/PVC St FT ca. m 75 (+/- 2 m) ² m borders ST / FT , RD...: Round conductor Conforms to the requirements according to VDE V , (IEC 62305) With PVC sheathing Conduction material Rope d /% m 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) D m borders Cu S9/Cu 9 Cu , s according to DEL notation; see material references. S9/Cu: Rope Standard ring approx. 100 m 7 Ø 3 individual wires (overall cross-section 50 ²) Conforms to the requirements according to DIN VDE (IEC 62305) TS 231
9 Earthing rod system ST Length Outer-Ø pcs kg ST / F 219/20 ST , /25 ST , /.. ST: Earthing rod for standard applications: High corrosion resistance Zinc support 70 µm With peg and bore for linking together Round pegs with two knurls Conforms to the requirements according to DIN VDE (IEC 62305) LightEarth earthing rod Length Outer-Ø pcs kg ST / FT LE-Erder , LE-Erder , LightEarth" earthing rod Expandable earthing rod system for erecting earthing s type ) High corrosion protection with reinforced zinc layer lso suitable for difficult soil conditions The LightEarth earthing system is connected using the pre-mounted sleeve Satisfies requirements according to DIN VDE (IEC 62305) For use with antenna earthing systems, lightning earthing systems, etc. Stainless steel LightEarth earthing rod Length Outer-Ø pcs kg V2 LE-Erder , LightEarth" earthing rod Expandable earthing rod system for erecting earthing s type ) High corrosion protection with reinforced zinc layer lso suitable for difficult soil conditions The LightEarth earthing system is connected using the pre-mounted sleeve Satisfies requirements according to DIN VDE (IEC 62305) For use with antenna earthing systems, lightning earthing systems, etc. Earthing rod system P Length Outer-Ø pcs kg V4 219/20 P-V , /20 P-V , /..P: Earthing rod with high contact force DIN 48852, Form Z, P system (undes Post) Very good contacting properties with lead ball in the bore hole With peg and bore for linking together V4 version, high-grade stainless steel ( no ) Conforms to the requirements according to DIN VDE (IEC 62305) Length Outer-Ø pcs kg ST / Cu 219/20 P-Cu , /..P: Earthing rod with high contact force DIN 48852, Form Z, P system (undes Post) Very good contacting properties with lead insert in the bore hole With peg and bore for linking together Cu version with a 0.5 copper sheath Conforms to the requirements according to DIN VDE (IEC 62305) 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 232 TS
10 D Ø /..: Earthing rod in robust design Length Outer-Ø pcs kg ST / FT 219/ , / , ST / F 219/ , DIN 48852, Form Z, OMEX system With peg and bore for linking together With hardened steel pins Version FT with zinc support, min. µm Conforms to the requirements according to DIN VDE (IEC 62305) pcs kg ST / FT LE- Spitze St FT 10 10, LE point Ø 25 : Striking point for mounting on earthing rods Earthing rod system OMEX Impact point for earthing rod system Ø 25 D Suitable for LightEarth system For deep earth Ø pcs kg TG / FT 1819/20P , /25P , /..P: Striking point for mounting on earthing rod Suitable for ST and P system D For deep earth Ø pcs kg TG / FT 1819/ , / , /...: Striking point for mounting on earthing rod Ø Suitable for OMEX system DIN 48852, Form Sp pcs LE- Kopf 1 LE head: Striking head for driving earthing rods using hand-held haer Suitable for LightEarth system Hardened Impact head for earthing rod system kg ST / FT 70, TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) ø For deep earth Ø pcs kg ST 1820/ , / , /..: Hardened for driving earthing rod s with hand-held haer Suitable for ST, P and OMEX systems Hardened DIN 48852, Form SP TS 233
11 Haer insert for earthing rod For deep earth Ø pcs kg ST 2500/ , / , /...: Haer insert for vibration haers Manufactured by Cobra M 47 SP-Super, Tex11 and COR 248 s earthing rod system ST, P and OMEX Hardened For deep earth Ø pcs kg ST 2510/ , /20: Haer insert for vibration haers Manufactured by tlas Copco, type F S-Super s earthing rod system ST, P and OMEX Hardened ø 47 ø For deep earth Ø pcs kg ST 2520/ , / , /...: Haer insert for vibration haers Manufactured by Wacker HF 25, HF 30S, EHU 25/220 s earthing rod system ST, P and OMEX Hardened ø 27 For deep earth Ø pcs kg ST 2530/ , / , /...: Haer insert for vibration haers Manufactured by osch USH 10, HSH 10 s earthing rod system ST, P and OMEX Hardened 19 For deep earth Ø pcs kg ST 2535/ , / , Haer inserts for vibration haers of other types and manufacturer on request. 5 ø /...: Haer insert for vibration haers Manufactured by Hilti TE 52/42, TE 72/, TE 92 s earthing rod system ST, P and OMEX Hardened 17.9 For deep earth Ø pcs kg ST 2536/ , / , /...: Haer insert for vibration haers with SDS- Max/TEY- mounting s earthing rod system ST, P and OMEX Hardened 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 234 TS
12 L LE haer: Haer insert for vibration haers Version pcs kg ST LE- Haer St Wacker 1 132, LE- Haer St Hilti 1 76, LE- Haer St osch 1 87, LE- Haer St SDS-Max 1 76, LE- Haer St tas Copco 1 76, ST Haer insert for earthing rod LE- Haer ST 1 200, L Suitable for LightEarth system for Wacker (HF 25, HF 30S) for Hilti (TE 52/42, TE72/, TE92) for osch (USH 10, HSH 10) for SDS-Max for tlas Copco (Sechskantaufnahme) for osch GSH27/UH27 (11304) / HS28 (12314) Hitachi H65SD Makita HM 1500 / HM1800 Hardened 101/ St Length Nominal size Ø pcs kg ST / FT , Cu 101/-Cu Cu , s according to DEL notation; see material references. 101/...: Interception rods, rounded ends Earth entry rods Ø 16 Ø 16 solid material oth ends rounded pcs kg ST / FT 101/F-1500 St FT , /F-2000 St FT , /F...: Interception rod with tabs With 2 attaching holes Ø 12 One end rounded Length Nominal size Ø L 200: oth ends rounded 200V1500 L Nominal size Ø pcs kg V , ST / FT , ø TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 16 ø pcs kg ST / F 204/KS St F / , /KS St F / , /KS: Multi-purpose ground insertion rod With flange-welded lug Rd 10 (final metre) With mounted heat-shrunk hose (corrosion proofing) Length Nominal size Ø TS 235
13 L L L 4 L Earth entry rods 204/KL pcs kg ST Rd , s according to DEL notation; see material references. 204/KL: Ground insertion rod, steel, hot-dip galvanised with separating piece 223/DIN and connector 5002/DIN L 204/KL-CU: Ground insertion rod, copper with separating piece 223/MS-DIN and connector 5002/MS DIN 25 ø 16 Profile rod earth Length pcs kg ST / FT 213/1000/DIN , /1500/DIN , /2000/DIN , /2500/DIN , /3000/DIN , /DIN: Profile earthing rod Cross-profile 50 x 50 x 3 With connecting strap 1 through hole Ø 13 2 through holes Ø 11 Length pcs kg ST / FT 213/1000/M , /1500/M , /2000/M , /2500/M , /3000/M , /.../M: Profile earthing rod 22 With 2 m strip steel section FL30 x 3.5 With 2 through holes Ø 11 Does not conform to DIN 48852, Part 1 30 ø Length pcs kg ST / FT 213/1500/F , /2000/F , /.../F: Profile earthing rod With 2 m round conductor lugs Rd 10 Does not conform to DIN 48852, Part 1 ø 10 Earthing plate x L x S pcs kg ST / FT 1816/F 500 x 500 x , /F 500 x 1000 x , /F 1000 x 1000 x , /F: Earthing plate as individual earth electrode With 3 m strip steel section FL30 x 3.5 With 2 attaching holes Ø FL 30 x3,5 ø 11 S=3 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 236 TS
14 max. FL30 255: Cross-connector for flat conductor : Max. FL30 x FL30 With separator plate Installed with 4 hex-head screws M6 x 20 (F) St pcs kg ST / FT FT 20 16, Cross-connectors max. FL : Cross-connector for flat conductor St pcs kg ST / FT FT 20 11, : Max. FL30 x FL30 Without separator plate Installed with 4 hex-head screws M6 x 20 (F) pcs kg ST / FT 256/-DIN 30 max. FL30 St FT 10 27, /-DIN 40 max. FL St FT 10 38, /-DIN..: Cross-connector for flat conductor : max. FL30 x FL30, max. FL40 x max. FL40 (F) Without separator plate Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 DIN 48845, Form H 256/-DIN 30 max. FL30 V2 pcs kg V , /-DIN..: Cross-connector for flat conductor : max. FL30 x FL30, max. FL40 x max. FL40 (F) Without separator plate Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 DIN 48845, Form H pcs kg ST / FT 256/DIN 30 max. FL30 St FT 10 35, /DIN 40 max. FL St FT 10 54, /DIN..: Cross-connector for flat conductor 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) : max. FL30 x FL30 (256/DIN 30), max. FL40 x FL40 (256/DIN 40) With separator plate Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 pcs kg ST / F 252/FL DIN 8-10 x FL30 St F 25 28, /FL DIN: Cross-connector for round conductor and flat conductor : Rd 8-10 x FL30 Installed with 4 hex-head screws M8-25, 4 hexagonal nuts M8 (F) DIN 48845, Form F TS 237
15 Cross-connectors 252/DIN Rd 8-10 St s according to DEL notation; see material references. 252/...: Cross-connector for round conductor pcs kg ST / FT FT 25 33, Cu 252/Cu-DIN Rd 8-10 Cu 25 38, : Rd 8-10 x Rd 8-10 With separator plate Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 252/DIN Rd 8-10 x 16 St pcs kg ST / FT FT 25 38, Cu 252/Cu-DIN Rd 8-10 x 16 Cu 25 43, s according to DEL notation; see material references. 252/...: Cross-connector for round conductor and interceptor/ground insertion rods : Rd 8-10 x Rd 16 With separator plate Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 DIN 48845, Form E pcs kg ST / F 253 Rd 8-10 St F 25 30, : Cross-connector for round conductor : Rd 8-10 x Rd 8-10 Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 (F) pcs kg ST / F 253 Rd 8-10 x 16 St F 25 29, : Cross-connector for round conductor : Rd 8-10 x Rd 16 Installed with 4 hex-head screws M8 x 25 and 4 hexagonal nuts M8 (F) 250 Rd 8-10/FL30 St pcs kg ST / FT FT 25 10, V2 250/V Rd 8-10/FL30 V , /...: Cross-connector for round conductor and flat conductor : Rd 8-10 x Rd 8-10 : Rd 8-10 x FL30 : FL30 x FL30 Installed with 2 hex-head screws M8 x 20 (F) TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 238 TS
16 10 L /...: Diagonal clamps 250/-FT FT L pcs kg ST / FT 40 Rd 6-22/max. FL , V2 250/-V 40 Rd 6-22/max. FL , ST / FT 250/S-FT FT 20 Rd 6-22/max. FL , Diagonal clamp For reinforced steels Ø 6-22 and flat conductor 50 x 4 Installed with screws M10 x 40 S version with screws M10 x 20 Simple installation with open slot /-O 250/-O: Diagonal clamps St For reinforced steels Ø 6-22 and flat conductor 50 x 4 Installed with screws M10 x 25 Simple installation with open slot With flange-welded bolts M10 x 40, inc. 2 washers and 2 nuts 259/ St FT pcs kg ST Rd 6-22/max. FL , pcs kg ST / FT Ø , V2 259/-V V2 Ø , ST 259/ St St Ø , /...: Parallel clamp Parallel clamp For connecting reinforced steels Ø Installed with screws M10 x 40 pcs kg ST / FT 1813/KL FL30- FL30 x Rd , /DIN: Variable earth connector Suitable for connecting Rd 10 x FL30, FL30 x FL30 Quick installation using hex-head screw M10 x 20 (F) Variable earthing terminal : Connection terminal pcs kg ST / FT 8-10, , Connection terminal 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) For connecting round conductor Rd 8-10 With 1 hex-head screw M12 x 40, 1 hexagonal nut M12 and 1 lock washer, stainless steel pcs kg ST 1814/FT 25 20, /ST 25 20, /...: Connection terminal For reinforced steels with diameters 8 14 and FL 30x5 Simple installation with open slot Side suspension option TS 239
17 4 Earthing fixed point Thread pcs kg V4 205/-M10-V M , /-M12-V M , /: Earth fixing point M10/M ø 18 ø10 For connecting to earthing systems, arresters and reinforcements With cover from plastic Contact plate: Ø 79 from high-grade stainless steel (V4) Ø 10 clamping bolt Including plastic cover for simple installation End piece D 5011 St FT Ø pcs kg ST / FT , V4 5011/V- 10 V , /V -12 V , : End piece Wedge connector For attaching to steel structures or bolting to earthing fixed points For attachments: Round conductor Rd 8-10 and flat conductor FL30 x 3.5 2x attaching hole Ø 11 1x attaching hole Ø D pcs kg ST / FT 1813/DIN 10/FL30 x FL , /DIN: Wedge connector Spacer DIN 48834, Form Suitable for connecting Rd 10 x FL30, FL30 x FL30 Quick installation with high contact force Length pcs kg ST / FT /FL30 x 3, , /L 10/FL30 x 3, , : Spacer for professional laying of round conductors and specialist conductors according to DIN VDE (IEC 62305) L 12.5 DIN Suitable for mounting round conductors Rd 10 or specialist conductors FL30 x 3.5 Expansion piece 1807 pcs kg l 25 27, : For expansion joints, for laying foundation earthing s Earthing block With 2 hex-head screws M10 x 30 2 hexagonal nuts M10, 2 plain washers, hot-dip galvanised steel and 2 serrated washers, stainless steel Length pcs kg ST / FT 1805/ , / , / , /...: For connecting different earthing systems With 2 mounting holes Ø /2: With 4 attaching holes 1805/4: With 8 attaching holes 1805/6: With 12 attaching holes (5x51) TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 240 TS
18 (5x51) 359 ø /...: For connecting different earthing systems With 2 mounting holes Ø /2: With 4 attaching holes 1805/4: With 8 attaching holes 1805/6: With 12 attaching holes Length pcs kg V4 1805/2 V , /4 V , /6 V , pcs kg Zn / FT 113/Z-FL Zn FT 100 6, /Z-HD-FL Zn FT 100 7, /Z...: Conductor holder with over-piece With female thread M8 or through hole for wood screws For flat conductor FL30 Sliding over-piece for quick installation Earthing block Cable bracket : Conductor holder 835 For round conductor Rd 8-10 and flat conductor FL30 x 3.5 Supplied with hex-head wood screw 6 x 70 and straddling dowel 910/N pcs kg ST / FT Rd 8/10/ FL30x3,5 1 12, Spacer clip pcs kg ST / FT 831/30 max. FL , /40 max. FL , /..: For flat conductors : FL30 and FL40 With mounting hole Ø 6.5 and 2 hex-head screws M6 x 16 (F) 831/..M6: For flat conductors pcs kg ST / FT 831/30 M6 max. FL , /40 M6 max. FL , TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) : FL30 and FL40 With attaching thread M6 and 2 2 hex-head screws M6 x 16 (F) 832/..: For flat conductors pcs kg ST / FT 832/30 max. FL , /40 max. FL , : FL30 and FL40 With mounting hole Ø 7 and 2 hex-head screws M6 x 16 TS 241
19 Spacer clip 833 max. FL30 833: For flat conductors pcs kg ST / FT 25 4, : FL30 With mounting hole 6.2 x 22 With 2 cylinder screws M6 x 16 and over-piece from hot-dip galvanised steel ottom section from polyamide, black /H max. FL30 pcs kg ST / FT , /..: For flat conductors : FL30 With spacer and cylinder screws M6 x 16 (G) With wood screw ø pcs kg ST / G 710/30 max. FL , /40 max. FL , /..: For flat conductors ø 10 : FL30 and FL40 With steel straddling dowel Ø 10, spacer and 2 cylinder screws M5 x 14 (G) 14 ø 30 pcs kg ST / G 708/30 SP max. FL , /..: For flat conductors : FL30 and FL40 With 2 cylinder screws M5 x 12 (G) and over-piece With square pin ø 4.75 pcs kg ST / G 708/30 HG max. FL , /40 HG max. FL , /..: For flat conductors : FL30 and FL40 With 2 cylinder screws M5 x 12 (G) and over-piece With wood screw ø Connection clip For deep Dimen- earth sion Ø pcs kg ST / FT 2710/20 St FT , /25 St FT , /..: ttaching clip for earthing rod connnector ST, P, OMEX and LightEarth systems On round conductor Rd 8-10 Including connector 5001/DIN TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 242 TS
20 40 For deep Dimen- sion earth Ø pcs kg ST / FT 2730/20 St FT , /25 St FT , V2 2730/20-V V , /..: ttaching clip for earthing rod connnector ST, P, OMEX and LightEarth systems On flat conductors Including hex-head screw for attaching flat conductors Connection clip ø 11 For deep sion Dimen- earth Ø pcs kg Cu 2735/20 Cu Cu , s according to DEL notation; see material references. 2735/20 Cu: ttaching clip for earthing rod connnector ST, P, OMEX and LightEarth systems On flat and/or round conductors Rd 8-10 For deep earth Ø pcs kg ST / FT 27/20 FT Rd 8-10/FL , /25 FT Rd 8-10/FL , : Multi-purpose attaching clip for earthing rod connnector Suitable for attaching round conductors Rd 8-10 or flat conductors to FL40 With separator plate Installed with 2 hex-head screws M10 x 30 and 2 hexagonal nuts M10 27/20-V V2 For deep earth Ø pcs kg V Rd 8-10/FL , : Multi-purpose attaching clip for earthing rod connnector Suitable for attaching round conductors Rd 8-10 or flat conductors to FL40 With separator plate Installed with 2 hex-head screws M10 x 30 and 2 hexagonal nuts M /20 Ms CuZn Cu For deep earth Ø pcs kg CuZn / Cu ,5/S95 ² 5 16, H s according to DEL notation; see material references. 2745/.. Ms: Terminal 40 For earthing rod connector Ø 20 or conductors 95 ² For round conductor attachments Rd with hex-head screws M10 x 25, copper (Cu) 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) Holders and accessories 356: Plastic corrosion-proofing band pprox. 1.2 thick Width: 50 and/or 100, petroleum jelly with cotton fabric insert Width Length m pcs kg , , Plastic corrosion-proofing band TS 243
21 Plastic corrosion-proofing band Width Length m pcs kg , , : Plastic corrosion-proofing band Holders and accessories Strip steel crimp Number plates pprox. 1.3 thick Width: 50 and/or 100, bitumen with polyester support fabric pcs kg ST / FT max. FL , max. FL , L = element length 366: For flat conductors : FL30 Length pcs kg Cu 311/N-CU RD 8 10 / FL30 Cu 50 6, V2 311/N-V RD 8 10 / FL30 V2 50 5, l 311/N-LU RD 8 10 / FL30 l 50 2, Cu 311/N-CU RD 16 / FL30 Cu 50 6, V2 311/N-V RD 16 / FL30 V2 50 6, l 311/N-LU RD 16 / FL30 l 50 2, /N-... Number plates To identify the point of separation to DIN Suitable for universal labelling (e.g. stamped numbers) Holders and accessories Holders and accessories 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) 244 TS
22 02 TS-Katalog 2008 / en / 28/05/2008 (LLExport_00596) TS 245
DEHN + SÖHNE. DEHNconductor System No Problems with Proximities
DEHN + SÖHNE DEHNconductor System No Problems with Proximities DEHNconductor System - New Possibilities for controling Proximities. For preventing dangerous flashovers among parts of external lightning
More informationGuide rail bracket (for adjustable heads)
(for adjustable heads) Part. 209 40 ø,5 ø10,5 2 2,5 115 15 42 5 11 37 72 4 70 Code 209 / 0754 MATERIALS: Bracket made out of reinforced polyamide black colour. FEATURES: To be used with heads Part.221,
More informationInstallation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
More informationMachine devices, jig devices
Machine devices, jig devices 853 K0697 Rolled thread studs DIN 6379 Material: Tempered steel. KIPP Rolled thread studs DIN 6379 Order No. D L B1 B2 Approx. weight g Surface finish: Thread rolled. Class
More informationC O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S
C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S January 2009 Issue 6 Valu Guide Brackets The Ultimate in Adjustability and Cost Savings Valu Guide brackets are part of a family
More informationKIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices
04000 Clamps Clamping devices 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 297 04010 Adjustable straps Tempered steel 1.1191 Black oxide finish nlm 04010-101 Suitable thrust
More informationDirectory chapter 02 - DIN Power (to 6 A) Types D, E, F, FM, 2F, F9, interface connectors I/U 02. 01. Technical characteristics types D and E... 02.
Directory chapter 02 - () Types D, E, F, FM, 2F, F9, interface connectors I/U Page Technical characteristics types D and E.............................. 02.10 Type D connectors.................... 02.11
More informationDryLin ZLW Belt Drive
Belt Drive +50º 0º DryLin toothed belt drives have been developed for the fast positioning of small loads. The linear units with toothed belt drive are corrosion resistant, light and compact, besides having
More informationANTENNA PARTS CATALOG
ANTENNA PARTS CATALOG Maco Antennas 302 S. East St. Mt. Carroll, IL 61053 www.macoantennas.net 815-244-3500 www.antennapartsoutlet.com SCREWS / BOLTS PART SIZE LENGTH DESCRIPTION PRICE S21 10-24 1/2" Machine
More informationEdition Perfect combination ratiopacpro Electronic P Edition kaging www clear order..biz information in the catalogue
ratiopacpro Overview... 0 Cabinets... 1 Y Desk-top cases Y Wall mounted cases... 2 Accessories for cabinets and wall mounted cases... 3 Climate control... 4 Desk-top cases... 5 06800002 Subracks/ 19" chassis...
More information14 PHOENIX CONTACT Courtesy of Power/mation. 1310 Energy Lane, Saint Paul, MN 55108. info@powermation.com - 800-843-9859 - www.powermation.
14 PHOENIX CONTACT PLUSCON circular is a circular connector for use in industrial automation. The range of design sizes available is varied, starting with the design sizes M5 to M8 and M1, for sensor/actuator
More informationDisplacement encoders
Displacement encoders Analogue and digital For measuring and positioning For use with pneumatic components 1 Displacement encoders Key features Analogue displacement encoders MLO-POT- -TLF Conductive plastic
More informationPermanent Stainless Steel Anchorage Point for Concrete, Solid Masonry and Steel Constructions
ABS-Lock X / X - SR Permanent Stainless Steel Anchorage Point for Concrete, Solid Masonry and Steel Constructions The ABS-Lock X system was developed to provide both a secure single anchorage point for
More informationSöll GlideLoc Aluminium Ladders. Vertical fall protection system Certified according to EN 353-1:2002 and CNB/P/11.073
Söll GlideLoc Aluminium Ladders Vertical fall protection system Certified according to EN 353-1:2002 and CNB/P/11.073 7 Söll GlideLoc Aluminium ladders Y-spar Profile 52 x 51 mm With connector Mounting
More informationLinkeo 19" freestanding cabinets
87045 LIMOGES Cedex France Telephone: (+33) 05 55 06 87 87 - Fax: (+33) 05 55 06 88 88 Linkeo 19" freestanding cabinets Page 1. General characteristics....1 2. Range....2 3. Technical characteristics...3
More informationK17.11 DOOR BOLTS K17 DOORS 01.09.2013
K17 DOORS K17.11 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Locking set series 86000...K17.11.03 2.
More informationTS 813 GROUNDING AND BONDING TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET GROUNDING
TORONTO TRANSPORTATION January 2012 TS 813 GROUNDING AND BONDING TABLE OF CONTENTS 1. DRAWINGS TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET
More informationVario-Series Accessories
Accessories and spare parts for GMW analogue panel meters and controllers Current Transformers pages 2-9 Shunt Resistors 10-11 Voltage Dividers 12 Power supply for indicator/controllers 13 Blanking Plates
More informationKnürr Smaract. Knürr Smaract. CompactRack
CompactRack Features Ample space for components and cabling provided in an efficient, compact design. The innovative frame concept with triangular extrusions ensures low weight while maintaining high stability.
More informationTubular connection elements
KIRÁY TRING KFT H-1151 udapest Mogyoród útja 12 14tel: 061307-3801 Tubular connection elements 429 KIRÁY TRING KFT H-1151 udapest Mogyoród útja 12 14tel: 061307-3801 Technical information on the tubular
More informationLinear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors
20000 Linear modules Lifting units Rotary modules Grip modules Inductive proximity switches Plug connectors 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 823 Notes 824 Technical
More informationDirectory chapter 04
M Directory chapter 04 D-Sub Mixed subminiature D connectors New Page D-Sub mixed connector system general information................... 04.02 Contact arrangements............................................
More informationSliding and Folding Door Fittings Sliding Door Accessories
Sliding door lock Toplock For 1- and 2-leaf sliding doors Suitable for toughened safty glass and laminated sheet glass Suitable for DIN left and DIN right Max. weight per door leaf 120 kg For glass thickness:
More informationSECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
More informationTemperature Sensors. Accessories. for Injection Molding. Types 6192B, 6193B,
Accessories Temperature Sensors for Injection Molding Types 6192B, 6193B, 6194B, 6195B Temperature sensors for measuring the contact temperature directly in the cavity at the surface of the solidified
More informationHUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast Anchor version HUS-A 6 Screw with hex head HUS-H 6 Screw with hex head HUS-I 6 Screw with hex head Benefits - Quick and easy setting - Low
More informationCatalog May 2015. Cable Accessories < 1 kv
Catalog May 2015 Cable Accessories < 1 kv Table of content Cable Accessories 1 Cable Accessories 1 kv Product range 2 Universal cleats 3 List of content 4 Notes 5 We reserve the right to make technical
More informationInstallation Instructions Hustler 6-BTV Trap Vertical
Installation Instructions Hustler 6-BTV Trap Vertical ASSEMBLY 1. Check the package contents against the parts list on page 2. 2. WARNING. Installation of this product near power lines is dangerous. For
More informationPPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
More informationCable Plug acc. to DIN EN 175301-803, Form A
Cable Plug acc. to DIN EN 175301-803, Form A Complete program Contact form 18 mm Also available with LED indicator Optional 4-pin version for pressure switch or impulse valves respectively Versions with
More informationPressure monitoring equipment for oil-sf 6. bushings, type GOEK
Pressure monitoring equipment for oil-sf 6 bushings, type GOEK Installation and maintenance guide 5693 827-6 en, Rev. 3, 2002-01-30 This document must not be copied without our written permission, and
More informationConsultants Handbook
Consultants Handbook CONSULTANTS HANDBOOK Welcome to our Wallis Designers Lightning Protection Handbook. This handbook offers a guide for any designers of the structural Lightning protection system to
More informationlindab duct suspension & support system Duct suspensions & Support systems
lindab duct suspension & support Duct suspensions & Support s lindab duct suspension & support Content Duct suspensions & Support s Duct suspension Duct suspension FB... DRSN... 0 DRSNR... 0 Channels and
More informationGivare NC-SRS 280 och 880
Givare NC-SRS 280 och 880 Aratron AB/Nordic Control, 02 03 SRS280SEALED ROTARY SENSOR PERFORMANCE ±2 Resistance ±20% Hysteresis (repeatability) Accuracy Applied voltage maximum Resolution Output smoothness
More informationDiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered
Electrical Temperature Measurement DiwiTherm, Resistance Thermometers Model TR75, with digital Display Battery or Solar Powered WIKA Data Sheet TE 60.75 Applications Machinery, plant and tank construction
More information1ZSE 2750-105 en, Rev. 8. Transformer bushings, type GOE and GOE(2) Technical guide
1ZSE 2750-105 en, Rev. 8 Transformer bushings, type GOE and GOE(2) Technical guide Original instruction The information provided in this document is intended to be general and does not cover all possible
More informationMounting Instructions for SP4 Power Modules
Mounting Instructions for SP4 Power Modules Pierre-Laurent Doumergue R&D Engineer Microsemi Power Module Products 26 rue de Campilleau 33 520 Bruges, France Introduction: This application note gives the
More informationPB accessories. PB accessories. Labelling option. Order Information B4-2728. Printed board handle A BZA42727 BZA42724.
Printed board handle A Assembly behind front panels Only use printed board handle in conjunction with printed board retainer A (6087-097) Insertion and extraction function Labelling option B4-2728 Item
More informationTrapezoidal-Connectors Series TMC
Trapezoidal-Connectors Series TMC Subminiature-D Connectors to DIN 41 652/IEC 807-3 General Series TMC connectors are available in 5 different housing sizes with 9, 15, 25, 37 and 50 pins. In applications
More informationMagnetic and Hydraulic-Magnetic Circuit Breaker 8340-G2...
Magnetic and Hydraulic-Magnetic Circuit Breaker 840-G2... Description Single, two and three pole magnetic circuit breakers with trip-free mechanism and push/pull on/off manual actuation. A choice of fast
More informationIndustrial circular connectors
Industrial circular connectors M 16 M 58 010 CONINVERS - M16 to M58 circular connectors for industrial applications CONINVERS GmbH, an independent company, is the specialist for M16 to M58 circular connectors
More informationOperating Instructions
Operating Instructions Cable Glands Ex d and Ex e with Compound > Contents 1 Contents 1 Contents...2 2 General Information...2 3 General Safety Information...3 4 Designated Use...4 5 Technical Data...4
More informationEMC Engineering Guidelines For Automation Systems PS 4 PS 416 04/97 AWB 27-1287-GB
EMC Engineering Guidelines For Automation Systems PS 4 PS 416 1st edition 04/97 Moeller GmbH, Bonn Author: Werner Albrecht Editors: Klaus Krüger, Thomas Kracht Translator: Chris Baker, Terence Osborn Contents
More informationSaferand easierinstallation
EN 85-07 Saferand easierinstallation IföSigninstallationsystem andifösignbuilt-incistern www.ifosanitar.com/sign Aneffectivesolution withmanyadvantages. Ifö Sign installation system makes life a little
More informationTECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. 2012NB Description 304mm (12") Automatic Thickness Planer CONCEPTION AND MAIN APPLICATIONS * Compact and light weight (27 Kg./59 lbs) automatic thickness planer for easier
More informationfor HACA fixed two-rail ladders with / without rear safety guard and fall arrest system
Instructions for assembly and use for HACA fixed two-rail ladders with / without rear safety guard and fall arrest system Englisch Please read before assembling! Caution: incorrect assembly can lead to
More informationmechanics PP-Profiles Panel Profiles PT-Profiles T-Groove Plates RE-Profiles Rectangular Profiles PU-Profiles Universal Profiles
Overview PP-Profiles Panel Profiles PP 50 PP 100 PP 150 PP 200 PP 0 B 4 PT-Profiles T-Groove Plates B 5 PT PT 50 RE-Profiles Rectangular Profiles B 6 RE 15 RE 30 RE40 RE65 PU-Profiles Universal Profiles
More information6720616592.00-1.SD. Flat roof. Rack Mounting. Installation instructions 6 720 647 036 (2010/11) AU
6720616592.00-1.SD Flat roof Rack Mounting AU Installation instructions 2 Contents AU Contents 1 Key to symbols and safety instructions....... 3 1.1 Explanation of symbols................ 3 1.2 Safety
More informationSOHOline and SOHO Slimline The SOHOline and SOHO Slimline offer a modular, sturdy and compact design
SOHOline and SOHO Slimline The SOHOline and SOHO Slimline offer a modular, sturdy and compact design Ideal installation for; Offices Branch Offices Schools Computer Aided Classes Government Offices Hotels
More informationSTAR Linear Bushings and Shafts Supplement RE 83 117/2001-08. Linear Motion and Assembly Technologies
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08 Linear Motion and Assembly Technologies STAR Linear Motion Technology Ball Rail Systems Standard Ball Rail Systems Ball Rail Systems with Aluminum
More informationFlamco Stainless steel mountings
S TA I N L E S S S T E E L M O U N T I N G S 9 Flamco Stainless steel mountings BRS-A BSF - SS RAIL R - SS GP - SS Edition 2007 / UK Stainless steel mountings Flamco offers the best attachment options
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 62305-3 Edition 2.0 2010-12 colour inside Protection against lightning Part 3: Physical damage to structures and life hazard INTERNATIONAL ELECTROTECHNICAL COMMISSION PRICE CODE
More informationHARTING Ethernet Cabling 8-poles Overview
Ethernet Cabling 8-poles Overview RJ45 Connectors [on page 8] System cables [on page 12] Distribution modules and Outlets [on page 17] Connectors [on page 20] System cables [on page 26] Panel feed-throughs
More informationFluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS
Fluid Level Gauge Fluid Level Sensor Temperature Switch FSA / FSK / TS up to size 381; to PN 0.5; to T = 80 C 1. Description 1.1. General FSA fluid level gauges, FSK fluid level sensors and TS temperature
More informationHORIZONTAL INSTALLATION
THERMO/SOLAR Žiar s.r.o. MANUAL FOR INSTALLATION PV SUPPORTING FRAMES HORIZONTAL INSTALLATION Technical alternation reserved A1410 1 12/2014 CONTENT ORD.NO. PAGE Mounting information 3 Mounting, flat roof
More informationDE Frame with C Series Sidelight
TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Screw gun with clutch adjusted #2 phillips tip #3 phillips tip Screwdriver (used to adjust frame on will using oval slots) Pry Bar Powder
More informationTARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
More informationInstallation information. METTLER TOLEDO MultiRange DW150 / DW150T wall scale
Installation information METTLER TOLEDO MultiRange DW150 / DW150T wall scale DW150 / DW150T wall scale Contents Contents Page 1. Installation... 2 1.1 Preparatory work... 2 1.2 Installing the wall plates
More informationTECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
More informationEARTHING AND BONDING AT SECONDARY SUBSTATIONS
DISTRIBUTION CONSTRUCTION MANUAL SECTION 4 - SUBSTATIONS ISSUE B SEPT 1996 4.4.4 EARTHING AND BONDING AT SECONDARY SUBSTATIONS 1 SCOPE This section of the Distribution Construction Manual lays down the
More informationLSA-PLUS Series 2 Connection and Disconnection Modules and Accessories
LSA-PLUS Series 2 Connection and Disconnection Modules and Accessories 2015 PRODUCT CATALOG 2ND EDITION LSA-PLUS Series 2 Connection and Disconnection Modules and Accessories A technically and commercially
More informationPower Cube Open Source Ecology Page 1. Power Cube. Version 4
Power Cube Open Source Ecology Page 1 Power Cube Version 4 Power Cube Open Source Ecology Page 2 Contents Table of Contents Power Cube... 1 Contents...2 Introduction... 3 Bill Of Materials...4 Discrete
More informationS OUNTING INSTRUCTION M M o u n t i n g k i t 2 &
M O U N T I N G I N S T R U C T I O N S instructions This document is protected by copyright. The SICK AG company retains this right. Reproducing this document in whole or part is only permissible within
More informationHARAX circular connector
Show navigation HARAX circular connector Technical characteristics Specifications IEC 60 352-4 IEC 60 9475-2 Approvals HARAX M8-S/M12-S Rated voltage Rated current Diameter of individual strands Conductor
More informationLinear Luminaire for Fluorescent Lamps Series EXLUX 6001
> As wall, ceiling and pendant light fitting or side entry lamp > Version with 2 lamps: 18 W, 36 W and 58 W > Central locking > All-pole disconnection by means of an N/C switch when the lamp is opened
More informationHOSE, TUBE, AND PIPE CLAMPS
hose, tube & clamp B/W pages 24/6/08 9:28 AM Page 2 HOSE, TUBE, AND PIPE CLAMPS TABLE OF CONTENTS Introduction 3 Construction 3 Application 3 Mounting 3 Standard Duty Clamps (HRL) Arrangements 4 Dimensions
More informationPipe Clamps and Accessories
Products 4.0 Products 4.1 Connection options to pipe clamps with Triple-Thread Connector NT 3G (M16, M10, M8) 4.2 Connection options to pipe clamps with Triple-Thread Connector NT 3G (3/8", M12, M10) 4.3
More informationTRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
More informationGo-kart for little race-drivers
Go-kart for little race-drivers Drill and drive. Go-kart What it lacks in speed, it more than makes up for in fun: the go-kart will excite little race-drivers. 1 Introduction It s only a go-kart, but it
More informationPREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS
SYSTEM COMPONENTS PREASSEMBLED ELEMENTS FOR FIFTING AND SLIDING DOORS s r ood gn i d i l s dna gn i t f i f r o f s t neme l e de l bme s s ae r P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS These
More informationDIAMOND Retractable Rodding Robot Model SPRAYROD-R
2004-12-21 2 1 (23) DIAMOND Retractable Rodding Robot Model SPRAYROD-R 2004-12-21 2 2 (23) Table of contents 1 TECHNICAL DESCRIPTION...4 1.1 MAIN DETAILS...5 1.2 COMPONENTS DESCRIPTION...5 1.2.1 Pneumatic
More informationDock Hardware & Accessory Products Catalog
Dock Hardware & Accessory Products Catalog Product Page # Product Page # Angle Brackets/Clips 8 Back Up Plate 5 Backing Plate/Hurricane Stop 10 Carriage Bolt Sets 4 Chain Retainer 10 Connector Pin Set
More information39HQ Airovision Air Handling Units
39HQ Airovision Air Handling Units Mounting instructions CONTENTS 1 - TRANSPORT AND LIFTING INSTRUCTIONS... 3 1.1 - General... 3 1.2 - Transport and storage... 3 1.3 - Roof edge protection during transport
More informationTerminal Boxes in Glass Fiber Reinforced Polyester (GRP)
Features Variants options Glass fiber reinforced polyester (GRP) enclosures Suitable for installation in Zones 0, 1, 2, 21 and 22 Certified Ex e, Ex ia and Ex tb 16 enclosure size options Various terminal
More informationTerminal Boxes Series 8146
Series > Enclosures in shock-resistant glass fibre reinforced polyester resin > basic enclosure sizes various heights > Fitted according to the customer's requirements > For terminals up to max. 00 mm
More informationTECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR 1.1.0 SCOPE : This specification covers design, manufacture, testing at manufacture s works before
More informationSITEMA PowerStroke. Technical Information TI-P11. 1 Function. 2 Applications. Mould Closing Devices series FSK. Contents
English translation of German original Technical Information TI-P11 SITEMA PowerStroke Mould Closing Devices series FS drive system for powerful forces on a short stroke hydraulic actuation closing force
More informationEJOT Spiralform. The thread formers for metal. EJOT The Quality Connection
EJOT Spiralform The thread formers for metal EJOT The Quality Connection Imprint Editor: EJOT GmbH & Co. KG Industrial Fasteners Division D 57319 Bad Berleburg Layout and Realisation: EJOT GmbH & Co. KG
More informationFront axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
More informationElo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors
Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...
More informationBETA Protecting SITOR Semiconductor Fuses
BETA Protecting SITOR Semiconductor Fuses /2 Product overview /3 /17 SITOR, cylindrical fuse design /22 SILIZED, NEOZED and DIAZED design Siemens ET B1 /2008 Product overview Overview Devices Page Field
More informationO SL. BPW Original spare parts Air suspensions series O / SL / AL BPW BERGISCHE ACHSEN BPW ORIGINAL SPARE PARTS. BPW Original spare parts
BPW riginal spare parts Air suspensions // BPW BERGISCHE ACHSEN BPW riginal spare parts Air suspensions series / / BPW RIGIN SPARE PARTS BPW riginal spare parts Air suspensions Contents Page Air suspension
More informationFLEXIBLE COPPER & ALUMINIUM CONNECTIONS. Product Range 1 VGL - ALLIED CONNECTORS
Product Range ROUND STRANDED COPPER CABLE Electrolytic Copper / Oxygen Free Copper Conforms to DIN 46438 Standards Finish: Bare Copper / Tinned / Silver-plated ROUND BRAID / ROUND STRANDED CABLE WITH OVERALL
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationpicomax The Pluggable Connection System
picomax The Pluggable Connection System TECHNOLOGY THIS SPECIALIZED CAN T MEET ALL REQUIREMENTS. YES IT CAN. CONTENTS picomax Pin spacing: 3. mm/0.138 in;.0 mm/0.197 in; 7. mm/0.29 in Versatile Pluggable
More informationKIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12 14tel: 061307-3801. E-mail:pzoli@kiralytrading.hu agi@kiralytrading.hu. Hinges
355 Technical information for hinges In the tables on the following pages are listed a large range of hinge variations. Many more variations are possible if hinges with guide tabs are required i.e. when
More informationTENSIONMETER ** code 183_LNRSTW **
Electronic tension meter for applications in textile and wire industry. 9 Tension ranges from 0.1-200 cn to 5-50 dan. Versatile instruments usable for applications in textile industry: e. g. 50 up to max.
More informationCABLE SUPPORT SYSTEMS
CABLE SUPPORT SYSTEMS eaturing the CADDY CAT HP J-Hook System Why CADDY CAT HP? Why Choose CADDY CAT HP over tray? ast and Easy to Install Much faster installation compared to conventional cable or ladder
More informationInstallation instruction CASAFLEX - Connecting piece DN 100
1 CASAFLEX - 11 10 114,3 x 4,5 3 5 2 4 1 7 6 8 12 9 Do not begin work until you have read the installation instruction carefully. 1 internal backing sleeve 2 graphite packing 3 connecting piece 4 thrust
More informationInductive sensor NI10-M18-Y1X-H1141
ATEX category II 1 G, Ex zone 0 ATEX category II 1 D, Ex zone 20 SIL2 as per IEC 61508 Threaded barrel, M18 x 1 Chrome-plated brass DC 2-wire, nom. 8.2 VDC Output acc. to DIN EN 60947-5-6 (NA- MUR) M12
More informationDESIGN BY: ARCH. GIUSEPPE INZITARI
DESIGN BY: ARCH. GIUSEPPE INZITARI 218 FOR HIGH THICKNESS FROM 12 TO 17.5 MM - GIUMAX GIUMAX 9500 Page 220 GIUMAX 8500 Page 227 ROLLERS Page 233 GIUMAX 4500 Page 236 GIUMAX 6500 Page 244 FROM 8 TO 12 MM
More informationHERZ-Thermal Actuators
HERZ-Thermal Actuators Data Sheet 7708-7990, Issue 1011 Dimensions in mm 1 7710 00 1 7710 01 1 7711 18 1 7710 80 1 7710 81 1 7711 80 1 7711 81 1 7990 00 1 7980 00 1 7708 11 1 7708 10 1 7708 23 1 7709 01
More informationIntroduction to Data Centre Design
Introduction to Data Centre Design Barry Elliott BSc RCDD MBA CEng Earthing, grounding and bonding November 09 Earthing what s the point Safety from electrical hazards Reliable signal reference within
More informationTopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
More informationPreface nivtec.com 3
nivtec.com Preface nivtec.com 3 nivtec 4 nivtec.com Planning with an Eye for Details nivtec.com 5 prolight+sound 2012 6 nivtec.com Meeting Point Fair Booth nivtec.com 7 Our Preparations 8 nivtec.com Enable
More informationHARTING Ethernet Cabling 4-poles Overview
Ethernet Cabling 4-poles Overview RJ45 Connectors [on page 8] System cables [on page 10] Distribution modules and Outlets [on page 20] Connectors [on page 22] System cables [on page 24] Panel feed-throughs
More informationproduces and delivers products worldwide can provide the optimal are dedicated to supplying you with superior advice and global support.
www.ppcinsulators.com The very Best. The very Best. That s what we deliver. ong od Insulators Only a company that develops, produces and delivers products worldwide can provide the optimal solution for
More informationLaserlyte-Flex Alignment System
Laserlyte-Flex Alignment System LaserLyte-Flex The LaserLyte-Flex Alignment System is a unique, interchangeable, low cost plug and play laser system. Designed specifically for aligning and positioning
More informationSyphonic Roof Drainage
Page 1 T E C H N O L O G Y 2:39 pm Syphonic Roof Drainage P L U M B I N G 23/5/03 A D V A N C E D Prod & Price Gd.for PDF Product Guide SYPHONICS Advanced Roof Drainage Technology Geberit Syphonics Geberit
More informationGuidelines for Earthquake Bracing of Residential Water Heaters
Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)
More information