How To Set Up An Ip Office Server And Call Manager On An Ip406 Server On A Network With A Network Vpn (Ipo) On A Pnet (Ip) On An Iphone Or Ipo (Ipa) On The

Transcription

1 Avaya Solution & Interoperability Test Lab Configuring Avaya IP Office Server and Cisco Call Manager IP Trunks with H.323 Signaling Issue 1.1 Abstract These Application Notes describe a simple configuration of H.323 IP Trunks between an Avaya IP406 Office Server and Cisco Call Manager. 1 of 26

2 * 8 # * 8 # 1. Introduction The sample configuration, depicted in Figure 1 illustrates an Avaya IP406 Office Server and Cisco Call Manager operating in different subnets and Virtual LANs (VLANs) connected by an 802.1Q trunk. IP406 Server is configured with extensions within the range to 19999, while Cisco Call Manager is configured with extensions within the to range. All IP endpoints are provisioned statically. Avaya IP Office Manager /PC Endpoint1 Avaya 4600 Series IP Telephone x Avaya P333- Management PWR Switch PC 802.1Q trunk Avaya TM IP406 Server IP Telephone - Cisco 7960 x Cisco Catalyst 4224 Avaya Digital Telephone x Cisco Call Manger VLAN /24 VLAN /24 Figure 1: IP Office to Cisco Call Manager Sample Configuration 2. Equipment and Software Validated The following equipment and software were used for the sample configuration provided: Equipment Software Avaya IP Office 406 Server 1.4(15) Avaya Cajun P333-PWR Switch Avaya 4612 IP Telephone 1.73 Avaya 6406D+ Digital Telephone N/A Cisco Call Manager 3.3 Cisco 7960 IP Telephone 3.1(12.1) Cisco Catalyst 4224 IOS 12.2(13T) 2 of 26

3 3. Configure the Avaya IP Office Server The steps that follow assume that the IP Office Management program is installed and running on a PC that is networked to the IP406 Server. The IP406 Server has been opened from the Manager program and the system password has been entered. Before any changes made in the Manager Program take effect, they must be communicated to the IP406 Office Server by selecting Save from the File menu item. Step 1 From the Manager Configuration Tree, select System and then the LAN1 tab to view the IP Office IP address. This is the address that will be used in the Call Manager Gateway Configuration of Section 4.4. As shown in Figure 2, disable the IP Office DHCP server. Figure 2: IP Office System-LAN1 tab Select the Gatekeeper tab. Check to ensure that Auto-create Extn Enable is checked. Autocreate Extn allows the IP406 Server to automatically provision an IP Phone when it registers to the IP406 Server. This capability will be used in Step 8. 3 of 26

4 Step 2 From the IP406 Server Configuration tree, select Line and then, from the right hand pane, right-click the mouse to select New to create the VPN line (H.323 trunk) that will be used for calls to and from the Cisco Call Manger as shown in Figure 3. Assign a unique Line number and Incoming Group ID and Outgoing Group ID. The number of channels should be adjusted to meet intersystem communication needs within the capacity of the network. Figure 3: IP Office VPN line-line tab 4 of 26

5 Step 3 Select the VoIP tab to enter the Gateway IP Address of the Cisco Call Manager as shown in Figure 4. Select Enable Faststart, Local Hold Music, Local tones, Out of Band DTMF and Allow Direct Media Path. Note: If calls may tandem through this system to another H.323 system, it may be necessary to disable the Allow Direct Media Path setting. Set H.450 Support to None. Press OK to complete the step. Figure 4: VPN Line VoIP tab 5 of 26

6 Step 4 Select Shortcode from the configuration tree and, in the right hand pane click New with the right hand mouse button to create a short code. Enter 2xxxx as Short Code to represent the Call Manager extension range of to Enter. as Telephone Number to forward all dialed digits on the outgoing call and enter the Line Group ID of 2, corresponding to the Outgoing Group ID of 2 for the H.323 VPN line to the Cisco Call Manager. Figure 5: Short Code 6 of 26

7 Step 5 From the Manager Configuration Tree, select Extension and then the extension ID corresponding to the station that will become x Select that extension and update its Extension value as shown in Figure 6. Select OK to enter the form. Figure 6: Extension of 26

8 Step 6 From the Manager Configuration Tree, select User and then modify an available user for extension as shown in Figure 7. Select OK to enter the form. Figure 7: User Form Step 7 At the Avaya 4600 Series IP Phone, press the buttons Mute A,D,D,R and enter the values from Table 1. Prompt Value Phone CallSv CallSvPort 1719 Router Mask FileSv Q Off VLAN ID 0 Save New Values? Yes Table 1: 4600 Series Phone Values After the phone goes through its restart procedure, at the Extn= prompt, enter with a blank password. 8 of 26

9 4. Configure the Cisco Call Manager 4.1. Access the Call Manager Administration Step 1 In the Internet Explorer address box, enter the IP address of the Call Manager and /CCMAdmin (e.g., /CCMAdmin) Step 2 Enter the correct login and password and click OK. The Call Manager will present the main screen shown in Figure 8. Figure 8: Call Manager Administration 9 of 26

10 4.2. System Settings Step 1 From the Main Menu, select System -->Server and select the Server of interest as shown in Figure 9. To add a new Call Manager Server, select Add a New Server and set the IP Address of the Server that IP Office is to connect to and a description, then press Update. The IP Address of this form is used in the IP Office line configuration of Figure 4 as the Gateway IP Address. Figure 9: Call Manager Server Configuration 10 of 26

11 Step 2 Select System-->Call Manager and the select the Call Manager to configure as shown in Figure 10. Ensure that Auto Registration is enabled for IP Phones and set the range of directory numbers to be assigned for these phones (for this configuration, Cisco IP phones will be allowed to auto register). Figure 10: Call Manager Form 11 of 26

12 Step 3 Select System-->Region and ensure that there is a region available that will be appropriate for communication with the IP Office as shown in Figure 11. If not, Select Add a New Region, enter a region name and the codec to be used within this region, as well as a codec to use for calls between this region and the existing regions. Press Update and then Restart Devices to effect this change. Figure 11: Region Configuration Step 4 Select System-->Location to define a location for the IP406 Server. Select Add a New Location and add a unique Location Name. Bandwidth for this configuration is 100,000 kbps as the systems are LAN connected. Figure 12: Location Configuration 12 of 26

13 4.3. Calling Search Space and Partitions Step 1 From the Call Manager main menu, select Route-->Partition Press Find to list all the system Partitions. If there is not an available partition, select Add a New Partition to add a partition for the IP406 server as shown in Figure 13. Figure 13: Partition Configuration Step 2 Select Update and Restart Devices as prompted to create the new Partition. Step 3 Select Route-->Calling Search Space to create or update a calling search space to include the partition associated with the IP406 server. 13 of 26

14 Figure 14: Call Search Space Configuration Step 4 Space. Press Update and then Restart Devices to affect the updated Calling Search 14 of 26

15 4.4. Adding in an IP Office H.323 Gateway Step 1 From the Call Manager main menu, select Device-->Gateway Select Add a New Gateway Set the Gateway type to H.323 Gateway and the Device Protocol to H.225 as shown in Figure 15 and press Next. Figure 15: Add a New Gateway 15 of 26

16 Step 2 Set the Gateway items as shown in Figure 16. The Device Name is the IP address of the IP406 server, the Location and Calling Search Space should correspond to those created for the IP406 Server earlier. Figure 16: Gateway Configuration Step 3 Press Insert and Reset the gateway to have the changes take effect. 16 of 26

17 4.5. Adding a Route Pattern Step 1 From the Call Manager Main menu, select Route-->Route Pattern and then select Add a New Route Pattern to create a route pattern for calls to IP Office. Step 2 Set the Route Pattern to 1XXXX so this pattern applies to all calls in the to range. Set the Partition to be part of the IP Office-175 partition created earlier, and the Gateway to the Gateway created in Section 4.4. Figure 17: Route Pattern 17 of 26

18 4.6. Configuring a Cisco IP Phone Step 1 Connect the Cisco IP phone to the Catalyst 4224 port with in-line powering enabled, as shown in Section 5, or with a local power supply. Press **# to unlock the configuration. Press Settings and then Network Configuration. Press Select. Set the values as shown in Table 2. Setting Value DHCP Enabled No IP Address Subnet Mask TFTP Server Default Router CallManager Admin. Vlan ID 50 Table 2: Cisco IP Phone Settings Save the settings and exit to the default screen. Step 2 At the Call Manager Main Menu, select Device-Phone and press Find to list the system phones. Select the phone whose device name or IP address matches the phone that was added. Configure the phone as shown in Figure 18. Set the Calling Search Space to the General Calling Search Space that was created in Section 4.3 which includes the IP Office Partition. 18 of 26

19 Figure 18: Phone Configuration 19 of 26

20 Figure 18: Phone Configuration, continued 20 of 26

21 Step 3 Select Add a New Directory Number to assign a Line and Number to the phone and ensure that the Calling Search Space is set to General. Figure 19: IP Phone Directory Number 21 of 26

22 Figure 19: IP Phone Directory Number, continued 22 of 26

23 5. Configuring the Cisco Catalyst 4224 Table 3 shows the Cisco Catalyst 4224 configuration, abbreviated to focus on the most relevant items for these Application Notes. Configuration interface FastEthernet5/1 description trunktoipoffice no ip address duplex auto speed auto switchport trunk native vlan 200 switchport mode trunk! i interface FastEthernet5/9 description callmanager no ip address duplex auto speed auto switchport access vlan 50! interface FastEthernet5/10 description ciscophone20000 no ip address duplex auto speed auto switchport mode trunk switchport voice vlan 50! Comments FastEthernet port 5/1 is the trunk to the P333T-PWR (VLAN 200). As a trunk, the packets passed are tagged with the VLAN identifier and a priority marking. FastEthernet 5/9 is the Call Manager port. The port is assigned to the call manager VLAN (VLAN 50). FastEthernet 5/10 is for the Cisco IP phone. In-line power is supplied by default. The port and phone are configured for tagged packets and for the voice VLAN as 50.! interface Vlan 50 ip address ip mroute-cache! interface Vlan 200 ip address ip mroute-cache h323-gateway voip bind srcaddr ! ip classless no ip route static inter-vrf no ip http server! VLAN 50 is established as the Call Manager VLAN with an interface to the router at VLAN 200 is the IP Office VLAN with an interface to the router at Table 3: Cisco Catalyst Configuration 23 of 26

24 6. Configuring the Avaya P333T-PWR Table 4 shows the Avaya Cajun P333T-PWR configuration, abbreviated to focus on the most relevant items for these notes. The key steps are in bold. Configuration Steps set port negotiation 1/1 enable set port flowcontrol all 1/1 off set port level 1/1 7 set trunk 1/1 off set port vlan 200 1/1 set port name 1/1 "ipphone" set port trap 1/1 enable set port classification 1/1 regular set port enable 1/1 set port powerinline 1/1 1 set port powerinline priority 1/1 2 set port negotiation 1/5 enable set port flowcontrol all 1/5 off set port level 1/5 5 set trunk 1/5 off set port vlan 200 1/5 set port name 1/5 "ManagementPC" set port trap 1/5 enable set port classification 1/5 regular set port enable 1/5 set port powerinline 1/5 1 set port powerinline priority 1/5 3 Comments Port 1 is the Avaya 4612 IP Phone. Set the layer 2 priority level to 7, the highest level. Set the port to be a member of the IP Office VLAN (VLAN 200). Set the port to be enabled. Set the Management PC port to be a member of VLAN 200. set port negotiation 1/12 enable set port flowcontrol all 1/12 off set port level 1/12 0 set trunk 1/12 dot1q set port vlan 200 1/12 set port name 1/12 "cisco4224" set port trap 1/12 enable set port classification 1/12 regular set port enable 1/12 set port powerinline 1/12 1 set port powerinline priority 1/12 3 set port disable 1/24 set port negotiation 1/24 enable set port flowcontrol all 1/24 off set port level 1/24 7 set trunk 1/24 off set port vlan 200 1/24 set port name 1/24 "ipoffice" set port trap 1/24 enable Set the Cisco Q trunk port to use VLAN tagging via the 802.1Q protocol. Set the port to be a member of VLAN 200. Set the IP Office 406 Server port to the highest priority level (7). Assign the port to VLAN of 26

25 set port classification 1/24 regular set port enable 1/24 set port powerinline 1/24 1 set port powerinline priority 1/ Verification Steps Table 4: P33T-PWR Configuration As always, perform basic network level verification (e.g., pings). Run the IP Office System Monitor with Settings-->H.323 set as shown in Figure 20 to monitor the H.323 exchanges with Cisco. Figure 20: H323 Monitor Options Use Cisco Call Manager Trace (Application-->Call Manager Serviceability) capabilities to create files similar to IP Office System Monitor files to follow call progress. 8. Conclusion By following the steps of these Application Notes, the reader will have successfully integrated an Avaya IP406 Office Server and Cisco Call Manager. These Application Notes can also be used as a basis to create more complex configurations, including those with WAN networks and dynamic IP address plans. 9. Additional References Similar Application Notes can be found at 25 of 26

26 Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by and are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. The information provided in these Application Notes is subject to change without notice. The configurations, technical data, and recommendations provided in these Application Notes are believed to be accurate and dependable, but are presented without express or implied warranty. Users are responsible for their application of any products specified in these Application Notes. Please any questions or comments pertaining to these Application Notes along with the full title name and filename, located in the lower right corner, directly to the Avaya Solution & Interoperability Test Lab at 26 of 26