AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE. Sprayer: PV VMA S.r.l. Via F. Crispi, 184 S. Maria della Versa (PV)
|
|
- Jeffry Reed
- 7 years ago
- Views:
Transcription
1 AGRICULTURAL MACHINERY FUNCTIONAL AND SAFETY TESTING SERVICE Test centre: Sprayer: PV Manufacturer: VMA S.r.l. Via F. Crispi, 184 S. Maria della Versa (PV) February 2007 Test Report No
2 Description of machine The implement is a trailed sprayer for use with ground crops. The machine frame is made out of painted steel, the main and auxiliary tanks are made out of polyethylene. A gauge is located on the front right of the main tank. The liquid level is indicated by a transparent external tube. A tank having a nominal capacity of 400 litres is available. The lower part of the tank and the machine frame are designed to allow the mounting of fixed wheels, to sustain the machine during work and guarantee a constant distance from the ground regardless of movements made by the prime mover. The implement is powered via the tractor PTO having a rated power of 540 rpm. The machine has a self-priming centrifugal bronze pump operated using v-belts with automatic tightener. The pump is located beneath the tank on the left. The pump serves to handle phytoiatric mixing (agitation and distribution) and to fill the main tank. Centrifugal brass pump Liquid is sprayed and conveyed pneumatically. Air flow is generated by a centrifugal fan with closed blades made from steel plate. The steel casing is endowed with 2 independent outlets at a distance of 180 from each other (above and below). The shaft transmitting drive to the fan includes a centrifugal clutch with automatic declutching, enabling the fan to turn independently in relation to the power source. Drive is transmitted from the PTO to the fan via an overgear with oil-bath lubrication and multiple chain. Transmission parts are located inside a pig-iron cast. Drive to the fan can 2/8
3 be interrupted using lever-controlled release gear. A fan having a runner diameter of 550 mm is available. The hydraulic circuit is of the constant pressure type. The lever to adjust pressure is located on the tank, while distribution on the two sides is controlled via electrical controls on a panel in the driver s cab. The pressure gauge is located close to the tank; it has a diameter of 100 mm, end scale of 6 bar and is in intervals of 0.2 bar. Liquid is supplied using a fan-based feed unit with 4+4 independent flow regulators situated in the lower section of the fan, and a second unit with blow guns located on the upper outlet of the fan. Liquid flow is adjusted by varying operating pressure and via adjustable dispensers endowed with an antidrip device placed on every liquid outlet. Control unit with pressure gauge. Lower fan-based distribution system 3/8
4 Size and weight length width 1450 mm 1000 mm Vertical pattern max height tank height empty weight total weight 2000 mm 1210 mm 250 kg 670 kg 3 point linkage cat. II Filling opening diameter 280 mm strainer height 230 mm horizontal distance 110 mm vertical distance 1210 mm height (m) left right 2.50 m Main tank l % % -5% 0% 5% 10% Hand wash tank 19.0 l Spraying unit 1+1 cannoncini 1+1 ventagli with anti drip device left right Pump TELLARINI - i 40 max flow rate 140 l/min height (m) Centrifugal fan m -15% -10% -5% 0% 5% 10% 15% 4/8 5/8
5 Main results of functional tests in the tank horizontal Residual (l) with back flow - with agitation 4,60 with back flow - without agitation -- without back flow - without agitation 0,45 inclined to right 0,25 inclined to left 0,50 inclined to rear 0,30 inclined to front 0,25 in the hoses: dilutable 1,08 dilutable residual 1 1,58 in the hoses: non dilutable 2 2,35 total residual 3,93 1 Liquid that can flow back into the main tank and can be diluted by the washing tank contents 2 Liquid that not can flow back into the main tank concentration 3 115% 110% 105% 100% 95% 90% 85% Agitator performance liquid sprayed (l) 3 Copper oxychloride concentration measured during the tank empying, after 16 hours standing and 10 minutes of agitation. Pressure gauge Fan diameter 100 mm flow rate power consumption distance between mark 0,20 bar 550 mm m3/h 25,5 kw accuracy 0,05 bar Air speed measured 0.50m from outlet 2,6 2,3 2,0 height (m) 1,7 1,4 1,1 0,8 0, air velocity (m/s) 6/8
6 Appraisal of performance Contents Assesment key 400 l X XX XXX Spray tank surface roughness XX µm > <30 Spray tank overvolume X % 5-8 >8-12 >12 Residual (related to the max value) XXX >2/3-3/3 1/3-2/3 <1/3 Spray tank content gauge up to 20% filling X % <2.5 Spray tank content gauge from 20% filling XX % < <2.0 Agitation system test (max concentration error) XX % > <5 Accuracy of pressure gauge (max deviation) XXX bar > > Accuracy of regulator (max deviation) XXX % <2.5 Adjustment of volume application rate n.a. % > <3 Pressure drop XXX % > <3 Application rate during spraying XX % > <3 Nozzle flow rate (provided/measured) X % > <3 Nozzle flow rate (measured/mean) XX % > <3 Nozzle flow rate (left/right) XXX % < <2.0 Fan flow rate (provided/measured) XX % > <3 Clean water tank n.a. % tank nominal volume >12-15 >15 Testing of Safety The machine is endowed with CE marking, an identification plate, safety pictograms, an instruction handbook and an EC manufacturer s declaration of conformity. The EC manufacturer s declaration of conformity certifies that the machine conforms to the following harmonised standards and technical specifications: UNI EN 907:1998, UNI EN 1553:2001, ISO 11684:1995. Checks carried out with reference to documentation sent by the Manufacturer did not show up inconsistencies with the contents of the aforementioned standards. The relative documentation has been filed. 7/8
7 The present test report is valid for five years or until reference standards for the sprayer, Model PV are altered. The machine has been submitted for certification at the request of the manufacturer. Functional testing was carried out in compliance with the provisions of the Protocol for the testing of functional characteristics of crop protection machinery (ENAMA rev.1 July 2002) at the Mechanics Section of the Department of Agricultural, Forestry and Environmental Economics and Engineering, University of Turin. Supervisor: Prof. Paolo Balsari Data collectors: Dr. Mario Tamagnone, Dr. Daniele Ghigo MANUFACTURER: VMA Srl Tel Fax website: E.NA.M.A. - ENTE NAZIONALE PER LA MECCANIZZAZIONE AGRICOLA VIA VENAFRO, ROMA TEL. 06/ FAX 06/ info@enama.it 8/8
CX (T3), great performance for unlimited versatility
CX90-100-110 (T3) The CX range is equipped with the new TIER-3 compliant Perkins 1104D series turbo engines. With powers of up to 102 hp, the new engines provide exceptional power and torque levels. The
More informationWANJET. Sprayers. Wanjet sprayers has been produced since 1978.
Sprayers Wanjet sprayers has been produced since 1978. Already from beginning was our assortment mainly based on high pressure sprayers with a pressure up to 150 bar. The idea about the high pressure is
More information367 000 Suction assembly for 1.000 l IBC and 205 l drums 1.060 mm suction tube. 367 003 Suction assembly for tanks 1.600 mm suction tube.
PUMPMASTER 2 accessories, other MOBILE oil dispensers PumpMaster 2 Accessories 01 OIL PUMPS 360 1 360 120 367 000 367 011 369 910 360 1 Wall bracket 360 120 Floor bracket 360 001 Bung adaptors 2" (M) connection
More informationTitan Makina Ltd. Şti. 1160. Sok. No: 9 Ostim 06370 Ankara Tel: + 90 312 354 9977 Fax: + 90 312 385 5611 Web: www.titanltd.com.
IS26 Concrete Spraying Machine IS26 Concrete Spraying Machine TECHNICAL SPECIFICATIONS Manipulator Max. vertical spraying reach : Max. horizontal spraying reach : Working lights : Spraying Head Rotation
More information1013 E. The engine for agricultural equipment.
1013 E. The engine for agricultural equipment.... -186 kw at 2300 rpm These are the characteristics of the 1013 E: Modern water-cooled 4- and 6-cylinder in-line engine Turbocharging with charge air cooling
More informationPHOTOVOLTAIC (PV) solar panels. Specification. Electricity - CE & ISO 9000 certified. 83W panel. 180W panel Maximum power:
PHOTOVOLTAIC (PV) solar panels Electricity - CE & ISO 9000 certified Photovoltaic solar panels convert sunlight into useful electricity. ZEDfabric supplies high quality mono-crystalline silicon cell PV
More informationVOYAGER 570G. 744A Sprayer Control
VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER
More informationProduct catalogue, pipe and sewer cleaning systems
Product catalogue, pipe and sewer cleaning systems Nozzles Rotorjet trolley Hose reels Cleaning devices www.hammelmann.com Contents (Navigation via Bookmarks) Rotorjet trolley Rotary joints, spray pipes
More informationArt.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS
Art.S001-S002 SOLAR MODULE WITH DELIVERY AND RETURN CONNECTIONS Technical Information sheet 0001/07/Rev01 ENG FUNCTION Series S001 and S002 circulation units are applied to the primary circuit of solar
More informationHydrostatic closed loop Bosch Rexroth. Fuel tank 180 l 180 l
R6480 RTH5.26S MACHINE MODEL ENGINE TRANSMISSION AXLES AND BRAKES PERFORMANCE WEIGHTS TANKS CAPACITIES HYDRAULIC CIRCUIT DIMENSIONS CONFORMTY TO STANDARDS Rotating telescopic forklift Maximum lifting capacity
More informationWith an excellent weight-to-power ratio of 37 kg/hp, the C-L model is ideal for general field work, as well as for PTO and transport applications.
Specially designed for farming applications with state-of-the-art technical solutions, the new Perkins engines meet the Tier 3 emission standards, while providing high power and torque levels with low
More informationSPACIOUS CABIN TEMPERATURE TELESCOPIC
THE ISEKI DIFFERENCE When you choose Iseki, you re not simply buying a tractor, you re investing in 80 years of industry-leading engineering and manufacturing experience. Experience that continues to produce
More informationTransformer oil cooler ALFA A02
A02 Transformer oil cooler ALFA Transformer oil cooler ALFA The transformer oil cooler ALFA is used to cool power transformers by means of forced air and oil flow. The oil in the cooler is circulated using
More informationSUPER 600. Tracked Paver SUPER 600. Pave Widths 0.5m 2.7m. Maximum Laydown Rate 200 tonnes/h. Clearance Width 1.2m
SUPER 600 Tracked Paver SUPER 600 Pave Widths 0.5m 2.7m Maximum Laydown Rate 200 tonnes/h Clearance Width 1.2m Mini Paver for Maximum Efficiency on Minor Job Sites T hanks to its compact size, variable
More informationx60.20 (T3) x60.30 (T3) x60.40 (T3) x60.50 (T3)
x60.20 (T3) x60.30 (T3) x60.40 (T3) x60.50 (T3) ENGINE perkins TIER 3 1104D-44TA 1104D-44TA 1104D-44TA 1104D-44TA ELECTRONIC INJECTION MAX. ENGINE POWER (ISO RATING) HP/KW 92,5 / 68 102 / 75 110 / 81 112
More informationSCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.
SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of
More information301.7D. Mini Hydraulic Excavator
301.7D Mini Hydraulic Excavator Engine Weights Gross Power (ISO 14396) 17.9 kw 24.3 hp Operating Weight with Canopy 1610 kg 3,550 lb Net Power 13.2 kw 17.7 hp Operating Weight with Cab 1720 kg 3,792 lb
More informationHR46 HARVESTER. Thinning Specialist
HR46 HARVESTER Thinning Specialist The history of Sampo Rosenlew forest machines Sampo Rosenlew today The founder of Sampo Rosenlew, mr Timo Prihti was born and raised on a farm. In Finland this means
More informationS KID S TEER L OADER SK818-5 SK818-5 SK 818-5. NET POWER SAE J1349 34,7 kw. OPERATING WEIGHT 2.910 kg. OPERATING CAPACITY 870 kg
SK 818-5 SK818-5 SK818-5 S KID S TEER L OADER NET POWER SAE J1349 34,7 kw OPERATING WEIGHT 2.910 kg OPERATING CAPACITY 870 kg S KID STEER L OADER PRESTAZIONI IN SICUREZZA Power, ease-of-use, and simplicity-of-operation
More information2. Crane standing on firm, horizontal ground.
The operating weight includes the basic machine with HD undercarriage, 2 main winches 300 kn with speed change gear and 11 m boom, consisting of A frame, boom foot (4 m), boom head section (6.4 m), boom
More informationQPM3 Low pressure pump for circulation of oil in hydraulic and lubricating systems
The Professional Choice in Fluid Management QPM3 Low pressure pump for circulation of oil in hydraulic and lubricating systems The Olaer Group is a global player specialising in innovative, efficient system
More informationHYDRAULICS. H91.8D/C - Computerized Open Surface Tilting Flow Channel - 10, 12.5, 15 and 20 m long
HYDRAULICS H91.8D/C - Computerized Open Surface Tilting Flow Channel - 10, 12.5, 15 and 20 m long 1. General The series of channels H91.8D has been designed by Didacta Italia to study the hydrodynamic
More information3304B. Marine Auxiliary Engine SPECIFICATIONS STANDARD EQUIPMENT ACCESSORY EQUIPMENT PERFORMANCE DATA. 56 bkw (75 bhp) 100 mhp @ 1200 rpm
Marine Auxiliary Engine SPECIFICATIONS 3304B 56 bkw (75 bhp) 100 mhp @ 1200 rpm Shown with Accessory Equipment I-4, 4-Stroke-Cycle-Diesel Emissions...IMO compliant Displacement... 7.0 L (425 cu. in.) Bore...
More informationSPEEDROC D30. Surface Drill Rig for marble, granite, sandstone and limestone in the dimension stone industry.
SPEEDROC D0 Surface Drill Rig for marble, granite, sandstone and limestone in the dimension stone industry. SPEED UP YOUR PROFITS SPEEDROC D0 IS A VERSATILE AND FLEXIBLE DRILL RIG, TAILORMADE FOR THE DIMENSION
More informationFig 1 Power Transmission system of Tractor
POWER TRANSMISSION SYSTEM Transmission is a speed reducing mechanism, equipped with several gears (Fig. 1). It may be called a sequence of gears and shafts, through which the engine power is transmitted
More informationTable of contents CAT DISC 25. Mower
Mower CAT DISC 25 ( Type PTM 370 : +.. 01001 ) Excerpt from operating manual Nr. 0370B00C.pdf Table of contents Swath Discs... 13 Swath Boards... 13 Safety points... 14 General maintenance hints... 14
More informationWWW.SMETS-TECHNOLOGY.COM COMBI. 7 SW COMBINED. SEWER. CLEANING. TRUCK ENGLISH 01. 2013 INNOVATIONS FOR POWERFUL PERFORMANCES
WWW.SMETS-TECHNOLOGY.COM COMBI. 7 SW COMBINED. SEWER. CLEANING. TRUCK ENGLISH 01. 2013 INNOVATIONS FOR POWERFUL PERFORMANCES COMBI. 7 SW COMBINED. SEWER. CLEANING. TRUCK PAGE 02 ENGLISH STATUS 01. 2013
More informationBLASTING SYSTEMS. Turbine blasting systems. Air blasting systems. Automatic Painting plants
BLASTING SYSTEMS Turbine blasting systems Air blasting systems Automatic Painting plants 1, Dust Collector 2, Cyclone Separator 3, Sand (shot) Storage Hopper 4, Bucket elevator 5, Primary separator 6,
More informationTechnical data. Danfoss DHP-A
Technical data Danfoss DHP-A An air heat pump which produces both heat and hot water Can operate efficiently down to -0 C Danfoss TWS tank gives plenty of hot water quickly and with low operating costs
More informationRH 12.5 RH 16.5. Crawler Excavator Specifications
Crawler Excavator Specifications RH 12.5 RH 16.5 RH 12.5 RH 16.5 Service weight t 34.1-38.1 39.9-43.6 Engine output kw 195 195 Trenching buckets (SAE) up to m 3 2.2 2.6 PMS three-pump hydraulics Electronic
More informationOWNER S/OPERATOR S - PARTS MANUAL CEMENT MIXER MODEL MX-80
OWNER S/OPERATOR S - PARTS MANUAL CEMENT MIXER MODEL MX-80 Read the Operator s Manual entirely. When you see this symbol, be aware that the subsequent instructions and warnings are serious - follow without
More informationValtra A Series Compact and Orchard models A53 / A63 / A73
Valtra A Series Compact and Orchard models A53 / A63 / A73 Full range of tractors in all size classes Individually Yours 2 Valtra is the one and only tractor manufacturer in the Nordic region. Our roots
More informationexactly what is needed
JUNIOR For many years of low-maintenance drainpipe cleaning Of course you are familiar with the benefits of drainage in the field or in the greenhouse. Crops grow better and working conditions for preparing
More informationMX R10 MX R16 MX R20 MX R28
FRONT LINKAGE MX R10 MX R16 MX R20 MX R28 User manual Please read carefully before using MX front linkage UK 361905 AC -1011 Original instructions Dear users, Thanks you for confidence in our product.
More informationSJT / SJM / SJP Large Vertical Pumps
SJT / SJM / SJP Large Vertical Pumps The Heart of Your Process SJT, SJM, SJP Large Vertical Pumps Product Overview SJT Turbine Ns 1800 < 5000 nq 35 < 110 SJM Mixed Flow Ns 5800 < 8300 nq 113 < 161 SJP
More informationProduct catalogue, abrasive cutting
Product catalogue, abrasive cutting Cutting nozzle assemblies Abrasive jet cutting system Abrasive hopper Abrasive material www.hammelmann.com Contents (Navigation via Bookmarks) Cutting nozzle assemblies
More informationNumber Wheeler P/N Description Set Rex P/N Notes 1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
More informationCOMPACT. Drilling COMPACT
COMPACT Our latest machine development still produced here in our own factory. This machine combines all our previous experience and knowledge in building drilling machines but at a reduced cost base.
More informationECOCIAT. Domestic hot water heat recovery unit
Heat recovery unit Domestic hot water High energy efficiency with R410A Compact and quiet Scroll compressors Brazed-plate heat exchangers Heating Heat recovery ENVIRONMENTALLY HFC R410A PROTECTION DE FRIENDLY
More informationitaltec PRINTED CIRCUITS EQUIPMENT PRINTED CIRCUITS EQUIPMENT Insulator machines Echting machines Special equipment and machines
PRINTED CIRCUITS EQUIPMENT PRINTED CIRCUITS EQUIPMENT Insulator machines Echting machines Special equipment and machines On customer request it is possible to supply: Benches for PCB Oven for PCB Chemicals
More informationO-I DUBI PLANT FANS Quotation Spec Data & Specifications
TECHNICAL DATA O-I DUBI PLANT FANS Quotation Spec Data & Specifications 1 page for the global informations + 12 pages for the fans data Revision 2 end april Global informations: These fans are a replacement
More informationNPTC LEVEL 2 AWARD IN THE SAFE USE OF PESTICIDES MODULE PA3
City & Guilds, BUILDING 500, ABBEY PARK, STARETON, WARWICKSHIRE, CV8 2LY Tel: 024 7685 7300 Fax: 024 7669 6128 Email: information@nptc.org.uk NPTC LEVEL 2 AWARD IN THE SAFE USE OF PESTICIDES MODULE PA3
More informationNumber Wheeler P/N Description Set Rex P/N Notes
1 604041 Base 1 4041 2 604042 Base Cover 1 4042 3 608849 Washer (M5) 2 4 600124 Spring Washer (M5) 2 5 600329 Rd Hd Machine Screw (M5x8) 2 6 604047 Strainer 1 4047 7 600204 Rd Hd Machine Screw (M6x10)
More information[ means: Save time, money and space! MAXXMILL 500. Vertical milling center for 5-side machining
[ E[M]CONOMY] means: Save time, money and space! MAXXMILL 500 Vertical milling center for 5-side machining MAXXMILL 500 MAXXMILL 500 is the ideal vertical milling center for the for the 5-axis operation
More informationControl blocks for two-hand start ZSB
Key features Function This pneumatic control block for twohand start ZSB is used where a manually started operation, such as the triggering of compressed air cylinders, would otherwise involve danger for
More informationCDS TROUBLESHOOTING SECTION I. VACUUM. 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg)
CDS TROUBLESHOOTING SECTION I. VACUUM 1.0. Weak vacuum at wand. Gauge reads normal (10hg to 14hg) 1.1. Clogged hoses or wand tube. Disconnect hoses and carefully check for an obstruction. 1.2. Excessive
More informationBelt Drives and Chain Drives. Power Train. Power Train
Belt Drives and Chain Drives Material comes for Mott, 2002 and Kurtz, 1999 Power Train A power train transmits power from an engine or motor to the load. Some of the most common power trains include: Flexible
More informationMÁQUINAS AGRÍCOLAS JACTO S.A. EDITION
AJ English version EDITION - 06/007 CODE - 9790 Parts catalog MÁQUINAS AGRÍCOLAS JACTO S.A. Rua Dr. Luiz Miranda, 650 7580-000 - Pompéia - SP - Brasil Tel.: +55 4 3405-00 - Fax: +55 4 345 306 E-mail: export@jacto.com.br
More information1300 MAXTRAK SPECIFICATION
CONE CRUSHER Crusher type: Liners: Standard concave: Lubrication: Adjustment: Control: Concave options: 1300 Automax Crusher. Manganese steel alloy mantle and concave. Medium Coarse. Pumped system having
More informationJCB TELESCOPIC WHEELED LOADERS TM180 AND TM220
JCB TELESCOPIC WHEELED LOADERS TM180 AND TM220 Incredible versatility is achieved through compact dimensions and the additional lift height provided by a telescopic boom The manoeuvrability of articulated
More informationOperating Instructions Drill rig DRU160
Operating Instructions Drill rig DRU160 Index 000 / 001 Original operating instructions 10988825 en / 20.10.2009 Congratulations! With a Hydrostress unit from TYROLIT you have chosen a tried and tested
More informationVibration and Noise Information
Author TOOJH Rev(1) Product Ergonomics & Industrial Design 9 Jan -14 Page 1(25) Vibration and Noise Information VIBRATION AND NOISE INFORMATION... 1 INTRODUCTION... 2 GENERAL INFORMATION VALID FOR MOST
More informationStandard offering (pumps)
MDM PUMPS LTD Spring Lane Malvern, Worcs. England. WR14 1BP This outlines what we typically supply. Tel: +44 (0)1684 892678 Fax: +44 (0)1684 892841 E-mail: Website: Standard offering (pumps) info@mdmpumps.co.uk
More informationWaste Oil Handling, Spill Containment & Lighting
58 Waste Oil Handling, Spill Containment & Lighting 372000 SAMOA Mobile Waste Oil Drainer & Extractor Drains and/or extracts waste oil from cars and light commercial vehicles Drain bowl capacity of 20
More informationINSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001
INSTRUCTION Industrial Sewing Machines First published : June 1997 Second edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's DLR Series. Read and study this instruction
More informationLANDPOWER, TIER 3 ENGINES AND ELECTRONIC TRANSMISSION FOR IMPRESSIVE PERFORMANCE.
, TIER 3 ENGINES AND ELECTRONIC TRANSMISSION FOR IMPRESSIVE PERFORMANCE. The new LandPower tractor has been redesigned with the adoption of the new F.P.T. Tier 3 engines and of an electronically-controlled
More informationMachining Center MODEL: VL-850
Machining Center MODEL: VL-850 MACHINE FEATURES 10HP Spindle Motor BT40/CAT40/DIN40 spindle dia. 150mm, 100% balanced with low vibration performs high precision machining. 8000 rpm spindle speed, ( Optional
More informationRI27-J CNG REDUCER INSTALLATION PROVISIONS & WARNINGS
RI27-J CNG REDUCER INSTALLATION PROVISIONS & WARNINGS Rev.01.02 BIGAS INTERNATIONAL AUTOGAS SYSTEMS S.r.l. Via di Le Prata, 62/66-50041 Calenzano Firenze ITALY Tel. 0554211275 - Fax 0554215977 http: www.bigas.it
More informationRouters and machining centres
Routers and machining centres Safe working practices HSE information sheet Introduction This information sheet gives practical guidance on safe working practices when using CNC routers and machining centres,
More informationHakomatic B 1050 and B 1100
Cleaning Technology Municipal Technology B 1050 and B 1100 P o w e r fu l, m an o eu vrable an d h ighly efficient: Batter y -p ower ed, r id e-on v e h i c l e s c ombin in g s w eepin g, scr ub b ing
More informationBACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12
BACKPACK SPRAYERS MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 INTRODUCTION Thank you for purchasing this CLARKE Sprayer, designed for use only with
More informationnet flywheel power 74 kw - 99 hp max operating weight 16 300 kg PAT DOZER BLADE CAPACITY 2.19 m 3
net flywheel power 74 kw - 99 hp max operating weight 16 300 kg PAT DOZER BLADE CAPACITY 2.19 m 3 150BBLADE Specifications ENGINE STAGE IIIA Net flywheel power (ISO 14396/ECE R120)...74 kw/99 hp Rated...2000
More information912. The engine for construction equipment.
912. The engine for construction equipment....... 24-82 kw at 1500-2500 min -1 These are the characteristics of the 912: Air-cooled 3-, 4-, 5-, 6-cylinder naturally aspirated in-line-engines. Direct injection.
More informationManual piston sampler...m 11
SAMPLING Manual piston sampler...m 11 Screw sampler...prec 22...PREC 100 Slide sampler...pr 55 Rotative screw sampler...prv Piston sampler...p 11 Sampler on belt conveyor...pba Rotating cup sampler...pgr
More informationHeavy Duty Industrial Air Compressors
HEAVY DUTY SERIES - VERTICAL TANK MOUNTED All units mounted on air receivers rated at 200 psi and CRN approved for Canada. All units may be ordered with magnetic starter (Starter supplied loose). All units
More informationAIRPORT. RUNWAY. CLEANER ENGLISH 01. 2013
WWW.SMETS-TECHNOLOGY.COM AIRPORT. RUNWAY. CLEANER ENGLISH 01. 2013 INNOVATIONS FOR POWERFUL PERFORMANCES ARC. 1000 AIRPORT. RUNWAY. CLEANER PAGE 02 ENGLISH STATUS 01. 2013 AVERAGE CLEANING RESULTS Rubber
More informationPENNELLI ROAD SWEEPER UNIT PVS 6000 SERIES. P.V.S. Srl DESCRIZIONE TECNICA COD. PVS 6000 ENG
ROAD SWEEPER UNIT PENNELLI PVS 6000 SERIES P.V.S. srl PENNELLI VEICOLI SPECIALI LE FOTO E GLI SCHEMI RIPORTATI SONO INDICATIVI NON VINCOLANTI PER L OFFERTA 1 INDEX... 2 GENERAL DESCRIPTION... 3 TECHNICAL
More informationTool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014. 0414/Rö
Tool Holder Catalog INDEX ABC VDI 25 LL3602.30051-10.04.2014 0414/Rö Disclaimer The illustrations in this documents may deviate from the delivered product. We reserve the right to make changes due to errors
More informationAdding Pneumatic Preset Counter. Type 497. Continuously visible preset Integrated pneumatic reset 3 or 5-digit display Convenient button setting
Adding Pneumatic Preset Counter Type 497 Continuously visible preset Integrated pneumatic reset 3 or 5-digit display Convenient button setting VARIABLE PILOT SIGNAL Using two pneumatic preset counters
More informationNEW HOLLAND T5OOO T5O5O T5O6O T5O7O
NEW HOLLAND T5OOO T5O5O T5O6O T5O7O T5OOO. A PERFECT MATCH BETWEEN PROVEN TECHNOLOGY AND MODERN ENGINEERING Powered by New Holland NEF Tier III compliant intercooled engines, New Holland T5000 tractors
More informationENGLISH FORK GUIDE 2013
FORK GUIDE 2013 ENGLISH 1 With a brand which is synonymous with specialists in forest products handling attachments, BOLZONI AURAMO offers its expertise and market leading attachments for all requirements,
More informationThe folding ROPS, available on the platform version, allows the operators to manoeuvre with ease when space is at a premium.
Available in the V (T3) series for vineyards and the F-N (T3) series for narrow orchards, this ultra-compact tractor range has been redesigned to offer improved gearbox controls, a new steering wheel with
More informationHYDRAULIC EXCAVATOR. ZAXIS-2 series
ZAXIS-2 series HYDRAULIC EXCAVATOR Model Code: ZX17U-2 Engine Rated Power: 11.0 kw (14.8 HP) Operating Weight: 1 750-2 020 kg Backhoe Bucket: ISO Heaped: 0.02-0.05 m 3 Versatile excavator with adjustable
More informationACCUMULATOR INSTALLATION
7001-7 ACCUMULATOR INSTALLATION BRAKE ACCUMULATORS I 308L93 Rae 7-59710 Issued 6-93 Printed in U.S.A 7001-8 Removal ACCUMULATOR VALVE 1. Park the machine on a level surface and lower the. loader bucket
More informationRPT SIGMA PUMPY HRANICE ROTARY LOBE DISPLACEMENT PUMPS 426 2.98 23.01
SIGMA PUMPY HRANICE ROTARY LOBE DISPLACEMENT PUMPS RPT SIGMA PUMPY HRANICE, s.r.o. Tovární 605, 753 01 Hranice, Czech Republic tel.: +4 581 661 111, fax: +4 581 602 587 Email: sigmahra@sigmahra.cz 426
More informationINDUSTRIAL DIRECT DRIVEN PISTON COMPRESSORS CL - CH - CK
INDUSTRIAL DIRECT DRIVEN PISTON COMPRESSORS CL - CH - CK CL - CH - CK Direct driven solution for industry Proven technology, solid construction The CL - CH - CK units are directly driven air-cooled, single
More informationH I G H S P I N W A S H E R E X T R A C T O R S H C 6 0 H C 6 5 H C 7 5 H C 1 0 0 H C 1 3 5 H C 1 6 5
H I G H S P I N W A S H E R E X T R A C T O R S H C 6 0 H C 6 5 H C 7 5 H C 1 0 0 H C 1 3 5 H C 1 6 5 HC 60 - HC 65 - HC 75 - HC 100 - HC 135 - HC 165 New look Matt door: uniform look of the front Ergonomic
More informationNumber Wheeler P/N Description Set Rex P/N Notes
1 607051 Base 1 A050 2 607052 Motor Cover 1 A052 3 600778 Socket Hd Cap Screw (M8x60) 2 4 607053 Scrap Receiver 1 A053 5 607054 Tank Upper Cover 1 A054 6 607055 Oil Pot 1 A055 7 607056 Strainer 1 A056
More informationElektra. Elektra. training. manual. manual. Coffee Grinder. Coffee Grinder SHARING THE PASSION
Elektra manual Coffee Grinder I T A L I A N E S P R E S S O C O F F E E M A C H I N E S AD: Holbein & Partners - Edition January 2006 Elektra training SHARING THE PASSION manual I T A L I A N E S P R E
More informationTECHNICAL INFORMATION Bulletin
Peerless Pump Company 2005 Dr. M.L. King Jr. Street, P.O. Box 7026, Indianapolis, IN 46207-7026, USA Telephone: (317) 925-9661 Fax: (317) 924-7338 www.peerlesspump.com www.epumpdoctor.com TECHNICAL INFORMATION
More informationLAMINAR FLOW CABINETS
LAMINAR FLOW CABINETS Vertical Laminar Flow Cabinets VLF 550 VLF650 VLF1000 VLF1200 VLF 1500 VLF1800 Monmouth Scientific's brand new range of Vertical laminar Flow (VLF) cabinets is available in six different
More informationJCB MIDI EXCAVATOR 8040 ZTS / 8045 ZTS
OPERATING WEIGHT: 9,480 lb (4,300 kg) 10,472 lb (4,750 kg) NET ENGINE POWER: 45 hp (33.1 kw) Interim Tier IV STATIC DIMENSIONS A Sprocket Idler Centers 6-1 (1845) 6-6 (1990) B Undercarriage Overall Length
More informationEXPORT w w w. k r a n m a n. c o m
EXPORT Kranman T1700 4WD series for ATV. Hydraulic unit KS-780 Facts: standard equipped T1700 Trailer T1700 4WD Total width 1.340 mm 4WD drive Hydraulic Total length 3000-3900 mm Pivoting stays 4 Load
More informationVolkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing
34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism
More informationPART 2 FORKLIFT HYDRAULIC SYSTEM
PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity
More informationExtremely compact in size to allow direct flange-mounting on vehicle engine or gearbox PTOs.
TXV - Presentation pumps with Load Sensing control variable displacement piston pumps ADVANTAGES pumps are variable displacement with pressure-flow control called Load Sensing. They self-regulate to give
More informationELECTRIC PERISTALTIC MORTAR POINTING PUMP
ELECTRIC PERISTALTIC MORTAR POINTING PUMP pointing gun & control valve ACF405 PERISTALTIC PuMP hopper feed roller & tube pump for refurbishment & repair trades heritage & conservation bridge & underground
More informationMachining Center MODEL: VH-610 MACHINE FEATURES
Machining Center MODEL: VH-610 MACHINE FEATURES 10HP Spindle Motor, CAT40 Spindle Taper 8000 rpm spindle speed ( Optional 10,000 or 12,000 rpm ) Super grade Turcite-B On X/Y/Z Slideways Hardened & Ground
More informationVARIABLE DISPLACEMENT AXIAL PISTON PUMPS. For truck applications
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS For truck applications TVP FEATURES Variable displacement axial piston pumps swash plate design ideally suited for open circuit truck applications. The compact
More informationRadial piston pumps type R and RG
Radial piston pumps type R and RG Operating pressure p max = 700 bar Delivery flow Q max = 91.2 lpm (at 1450 rpm) Geometric displacement V g max = 64.2 cm 3 /rev. 1. General Motor pumps and hydraulic power
More informationCold milling machine W 1000 F. Technical specification
Cold milling machine W 1000 F Technical specification Technical specification 2 Cold milling machine W 1000 F on four wheels Cold milling machine W 1000 F on four crawler tracks Milling width max. mm 1,000
More informationSunMaxx Solar Filling Station Operating Instructions
SunMaxx Solar Filling Operating Instructions Content 1. Declaration of conformity... 2 2. Introduction... 2 3. Transportation and unpacking... 4 4. Mounting and commissioning... 5 5. End of operation...
More informationThe conditions below apply to the curves shown on the following pages.
GENERAL INFORMATION STAINLESS STEEL, SILVERLINE, EVERGREEN & GOLDLINE SERIES PERFORMANCE CURVE CONDITIONS The conditions below apply to the curves shown on the following pages. a. The Performance curves
More informationELECTRONIC CONTROLS. Filter Life
MARCH 2014 1000 MH, 1350 MH, 2100 MH, 2200 MH, 2350 MH, 2500 MH, 2550 MH 3000 MH 4000 MH Make your motorhome more at home on the road with an Allison fully automatic transmission. Whatever your travel
More informationNew Holland T7.270 Auto Command
Datasheet DLG PowerMix New Holland T7.27 Auto Command Applicant New Holland Agricultural Equipment SpA Via Plava 8 I-1135 Torino www.newholland.com Test performed by DLG e.v. Test Center Technology and
More informationSound pr. (db(a)) Phone: +90 216 394 12 82 Pressure hpa 960.075. Fax: +90 216 394 12 87 Capacity kw 1200.000
Hybrid-Re-Cooler V-2x8 - Offer no. 1328 Sound power (db(a)) Sound pr. (db(a)) Company Schenkel & Partner GmbH 1 Branch Ingenieurbüro Street Bahnhofstrasse 44 Country/ZIP/City 8 Zürich Installation Credit
More informationMH 3M & 4M. High pressure washers with hot benefits
MH 3M & 4M High pressure washers with hot benefits The EcoPower boiler provides high efficiency and lowest equivalent fuel consumption as certified by EUnited. All key functions placed for optimal ease-of-use.
More informationFLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES
01D351-GB FLOAT SWITCHES FLOW SWITCHES FOR LIQUIDS PRESSURE SWITCHES DOLOMIT FLOAT SWITCHES The DOLOMIT float switches find application in liquid level control in tanks and wells; they require connection
More informationMANTA Piston Distributor for Oil and Fluid Grease
MANTA Piston Distributor for Oil and Fluid Grease Function Piston distributors meter out and distribute the oil delivered by an intermittently actuated pump. The quantities of oil for the individual lube
More informationSPILL CONTAINMENT PALLETS
SPI CONTAINMENT PAETS According to the regulations the storage of lubricant or fuel drums in industrial or workshop environments requires suitable containers which can collect the fluids in case of eventual
More information