TORNADO T8/SM and T8/ML
|
|
- Agatha Davidson
- 7 years ago
- Views:
Transcription
1 A TORNADO T8/SM and T8/ML Respiratory Protective Systems Operating and Maintenance Instructions...1 Betriebs- und Wartungsanleitung...4 Gebruiks- en onderhoudsaanwijzingen...8 Instructions d'utilisation et d'entretien...11 Instrucciones de Funcionamiento y Mantenimiento...15 Instruções Operacionais e de Manutenção...19 I Istruzioni d'uso e manutenzione...22 Operations og vedligeholdelses instruktioner...26 Bruksanvisning och skötselinstruktioner...29 Bruks- og vedlikeholdsveiledning...32 Käyttö- ja huolto-ohjeet...35 Part No. T/8/LFT Issue A Jan 01 Art No
2 1 4b a 8b 3 5 4a 4a 5 3 T8 2
3 Protector Respiratory Protector Technologies Ltd Pimbo Road, West Pimbo, Skelmersdale, Lancashire WN8 9RA United Kingdom Tel: +44 (0) Fax: +44 (0) Protector Technologies Pty Ltd. 137 McCredie Road, Guildford, Australia 2161 Tel: +61 (0) Fax: +61 (0)
4 Fig 1 Fig 2 Fig 3
5 TORNADO T8/SM and T8/ML Respiratory Protective Systems WARNING TORNADO powered respirators are designed for use by personnel who are familiar with workplace hazards. This leaflet must be read together with the user leaflets for T/POWER and T/FILTER. DO NOT use in oxygen deficient atmospheres (<19.5%), confined spaces, stills, tanks, or areas immediately dangerous to life or health. DO NOT use equipment that is damaged. Check that the type of filter(s) used with T/POWER are suitable for the workplace hazard. DO NOT use if there is no airflow from the T/POWER or if the airflow output is low (see the Flow test detailed in T/POWER). DO NOT confuse the markings on a filter relating to any European Standard other than EN12942 with the classification of this device when used with this filter. DO NOT use T8 with T/POWER switched off. In the unlikely event that T/POWER fails to supply air while in a hazardous area, continue to breath from the half mask and go immediately to a safe area. The halfmask will continue to provide a degree of respiratory protection. T8 is not suitable for use with T/A/LINE. T8 must not be used where contaminant concentration exceeds 20 times its Occupational Exposure Limit, or 1000 ppm by volume. T8 must only be used with the T8 breathing hose. DO NOT use other TORNADO breathing hoses. It is unlikely that the requirements for leakage will be achieved if hair, spectacle side arms or clothing intrude into the faceseal. T8/SM and T8/ML SPECIFICATION Facepiece T8/SM and T8/ML Description Halfmask Classification: EN TM2 Minimum design flow rate 110 L/min Nominal protection factor 200 Assigned* protection factor 20 Operating temperature range -10 o C to 40 C Maximum operating humidity 95% Material Silicone elastomer *According to BS4275 :
6 INTRODUCTION To aid component identification in the following procedures, bracketed numbers after a component show component's location in the T8 diagram inside the front cover. DONNING Note: Initial donning procedures should be supervised by a competent person. Select the appropriate size of mask: S/M or M/L. 1. Check that all parts of T8 are clean and in good condition. 2. Check that the breathing hose seal (8b) is in place and in good condition and screw the breathing hose (8a) firmly, hand-tight, onto the halfmask (Fig 1). Do not over-tighten. 3. Adjust the harness (1) so that the buckle is away from the mask and the head pad rests on top of the mask. Place the strap around the neck (Fig 2). Note: Once a comfortable fit has been achieved for a given wearer, there should be no need to alter the head-strap length when donning in the future. 4. Place the halfmask on the face and adjust until the faceseal (2) fits smoothly against the face. 5. Pull the head pad onto the crown of the head (Fig 3) and adjust the harness, feeding the harness through the anchors to equalise the pull on the anchors. 6. The mask should feel firm against the face with no undue movement. If it does not fit, or is uncomfortable, adjust the harness (1) length using the nape buckle (It may be easier to do this prior to donning the mask). Excessive tightening causes discomfort and may distort the face seal. 7. Test the faceseal by blocking the breathing hose inlet with the palm of the hand and inhaling. Check that the mask pulls onto the face until the wearer exhales. If there is a leak, check the faceseal, breathing hose seal (8b) and the exhalation valves (4a). It may be necessary to try the alternative size of mask. Do not use the mask if a good fit cannot be achieved. 8. Arrange the breathing hose so that it trails freely down the back and is not kinked, likely to snag, or be crushed. 9. Follow the instructions in the T/POWER leaflet to: Attach the breathing hose to T/POWER, Perform the airflow test, and Check the filters. AFTER USE WARNING: DO NOT remove the halfmask until well clear of the hazard area. 1. Take off the halfmask and undo the breathing hose. 2. Clean the mask and the outside of the breathing hose with a synthetic sponge moistened in a mild solution of soap and warm water, or TriGene solution. Note: Water MUST NOT enter the breathing hose. 3. Rinse the mask thoroughly under clean running water and hang it by the harness until thoroughly dry. DO NOT use radiant heat or sunlight to speed drying. 4. Use TriGene wipes to sanitise the faceseal. 5. After cleaning, check that all components are in good condition. Worn or damaged items must renewed prior to further use. MAINTENANCE Important: Check the valve flaps (4a) and (4b) visually every 3 months to ensure that they are clean and undamaged. Check that the faceseal (2) and valve flaps are flexible. Valve flaps must be replaced annually. Important: The breathing hose elbow is glued to the halfmask shell (3) and must not be removed. If an elbow is removed or damaged, the shell assembly must be renewed. 2
7 Important: Exhalation valve flaps should be as new with no damage. They are marked with a code indicating the year of manufacture. The letter Y' corresponds to 1994 and a dot is added each year thereafter, so Y...' is Discard valve flaps that are more than 6-years old. Storage Note: Plastic and rubber components must be stored in clean dry conditions, away from direct sunlight and heat, within a temperature range 10 o C to 30 o C and in humidity not exceeding 65%. Replacing the Harness - Push the harness anchors from the shell (3) to free the harness. Push the replacement harness anchors into the slots in the shell assembly. Check that they click into place and are securely attached. Replacing the Exhalation Valve Flap and Valve Cover - There are two exhalation valves. To replace an exhale valve flap, or valve cover: grasp the lower edge of the green valve cover (5) and pull off the covers. Grasp the valve flap (4a) and pull from the faceseal (2). Check that the replacement flaps are in good condition, and carefully pull the stem of each flap through the centre of the valve frame, until the flap lies flat against the frame. Replacing an Inhale Valve Flap - Pull the valve flap (4b) from the locking ring (6). Check that the replacement flap is in good condition and carefully attach the flap over the tab on the locking ring. Check that the flap is flat against the frame. Replacing the Shell Assembly, Locking Ring and Thrust Washer - Unclip and remove both exhale valve covers (5). Turn the inhale valve locking ring (6) anti-clockwise and remove it. Align the notches on the thrust washer with the tabs on the elbow, and remove the thrust washer (7). Remove the shell. Fit the replacement shell (3) over the faceseal and ensure that the exhale valve apertures engage in the groove in the rim of the valve frames. Fit the replacement thrust washer (7) and locking ring (6), taking care to align the notches on both with the tabs on the elbow. Clip both exhale valve covers (5) into place. Push the harness anchors into the notches on the shell. Breathing Hose and Seal - Unscrew the breathing hose and discard the seal if it is 6-years old, if it is damaged or cannot form a good seal. MAINTENANCE RECORD Record details of all items replaced during maintenance in the table at the end of this book. SPARE PARTS Item, See T8 DESCRIPTION Part No. 1 Harness kit KIT94/2 3 Elbow / Shell Assembly KIT/T8SHELL 4 Valve kit (2 exhale (4a), 4 inhale valves (4b)) KIT94/1 5 Valve cover (green) RXHM7034/Y 6 Locking ring (Pack of 2) Thrust washer for locking ring (Pack of 2) T8 Breathing hose (8a) with seal (8b) (Pack of 3) T8/HOSE 8b T8 Breathing hose seal (Pack of 3) T8/H/SEALS Notified Body INSPEC CERTIFICATION LTD (NUMBER 0194), Upper Wingbury Courtyard, Wingrave, Aylesbury, Buckinghamshire, HP22 SLO, UK 3
Operating and Maintenance Instructions
Operating and Maintenance Instructions WARNINGS Before using this equipment, read the contents of EN 529 : 2005 and familiarise yourself with the requirements for respiratory protective devices and their
More informationFLITE CONFINED SPACE RESCUE COMPRESSED AIR BREATHING APPARATUS
FLITE CONFINED SPACE RESCUE COMPRESSED AIR BREATHING APPARATUS 1034990 D 05.2012 CE0086 Contents WARNINGS... ii 1. INTRODUCTION... 1 1.1 BREATHABLE AIR... 1 1.2 AIRLINE PRESSURE AND FLOW... 1 1.3 TRAINING...
More informationElgin Fire Department
Breathing Operations Elgin Fire Department Safety - Respiratory Protection Program - Self Contained Apparatus (SCBA) Policy # 2024.01 Issued: 09/08/06 Subject: Purpose: Scope: Self Contained Breathing
More information7500 Series. Important: Keep these user instructions for reference.
7500 Series Respirator Half Facepiece User Instructions for 3M Silicone, Small 7501, Silicone, Small 37081, Silicone, Medium 7502, Silicone, Medium 37082, Silicone, Large 7503, Silicone, Large, 37083 Half
More informationBACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12
BACKPACK SPRAYERS MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 INTRODUCTION Thank you for purchasing this CLARKE Sprayer, designed for use only with
More informationSpiromatic Face Mask and breathing valve User manual
Spiromatic Face Mask and breathing valve User manual Contents Safety notice... 4 Mask and breathing valve... 5 Checking before use Leakage test Putting on the mask... 7 Testing of the positive pressure
More informationCaboose Too Rear Seat Instruction Manual 0090X & 0091X Series
Caboose Too Rear Seat Instruction Manual 0090X & 0091X Series Joovy 2919 Canton Street Dallas, TX 75226 (877) 456-5049 Fax: (214) 761-1774 Email: customerservice@joovy.com Web Site: www.joovy.com ! WARNING
More informationCAR SEAT/ STROLLER INSTRUCTION MANUAL
CAR SEAT/ STROLLER INSTRUCTION MANUAL English PM-0624AB 3/98 Do not use this 4-in-1 System until you read and understand these instructions! IMPORTANT INFORMATION Thank you for selecting this 4-in-1 System
More informationLunette 2 Series. Curved Fixed Frame Projection Screen. User s Guide
Lunette 2 Series Curved Fixed Frame Projection Screen User s Guide Important Safety and Warning Precautions Please follow these instructions carefully to ensure proper maintenance and safety with your
More informationCHILD BOOSTER SEAT. Instructions for Installation & Use Series No. 4050/A/2013 IMPORTANT: KEEP THIS BOOK IN THE PLACE PROVIDED ON THE CHILD RESTRAINT
CHILD BOOSTER SEAT Instructions for Installation & Use Series No. 4050/A/2013 IMPORTANT: KEEP THIS BOOK IN THE PLACE PROVIDED ON THE CHILD RESTRAINT INDEX PAGE 3 4 6 7 9 10 14 19 21 22 INTRODUCTION WARNINGS
More informationPOP Pushchair. Instructions
POP Pushchair Instructions Important: Keep for future reference Please read these instructions carefully before using your new pushchair Keep them in a safe place so that you may use them in the future
More informationHow To: Retrofit the Morimoto Mini D2S bi-xenon Projectors
How To: Retrofit the Morimoto Mini D2S bi-xenon Projectors Warning: By reading this document I agree that it is only intended to be used as an educational guide. The Retrofit Source Inc. makes no guarantee
More informationStainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
More informationBack Pack Sprayer. Operator's Manual MODELS MS - 40 MS - 50
Back Pack Sprayer Operator's Manual MODELS MS - 40 MS - 50 WARNING DANGER Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood
More information1 TON FOLDING CRANE CFC1000
1 TON FOLDING CRANE CFC1000 OPERATION &MAINTENANCE INSTRUCTIONS 0401 SPECIFICATIONS MAXIMUM SAFE WORKING LOADS (kg) 1 2 3 4 1000 750 500 250 MAXIMUM LIFT HEIGHT - 1920mm HYDRAULIC RAM OIL CAPACITY - 450CC
More informationArtisan Thermostatic basin mixer. Fitting Instructions & Contents List
Artisan Thermostatic basin mixer Fitting Instructions & Contents List Please keep these instructions for future reference and request of replacement parts 1. Introduction Thank you for choosing Bristan,
More informationHow To Use 3M Tm Tmr.Com
6000 Series Respirator Full Facepiece User Instructions for 3M TM 6700 (Small) 07138 (Small), 6800 (Medium) 07139 ( Medium), 6900 (Large) 07140 (Large) Full Facepieces (Keep these instructions for reference)
More informationAssembly overview - fuel tank
Assembly overview - fuel tank vw-wi://rl/n.en-gb.k02589829.wi::33090894.xml?xsl=3 Page 1 of 2 Assembly overview - fuel tank 1 - Fuel tank 2 - Sleeve When removing, support using engine and gearbox jack
More informationDMSG_0152_0112_V4 Mamas & Papas (Holdings) Ltd. 2012 Dream Swing - 1 -
DMSG_0152_0112_V4 Mamas & Papas (Holdings) Ltd. 2012 Dream Swing - 1 - DREAM SWING THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE. Read the entire instruction before
More informationCYLINDER REFILL AND INSPECTION
Refill/Inspection Procedure 1 CYLINDER REFILL AND INSPECTION REVISION 2.01 DATE 11.1.2013 1.0 General Information This procedure outlines the process in which Authorized BCA refill centers should complete
More informationSHOT BLAST CABINET MODEL NO: CSB20B
SHOT BLAST CABINET MODEL NO: CSB20B PART NO: 7640110 USER INSTRUCTIONS GC0216 INTRODUCTION Thank you for purchasing this CLARKE Shot Blast Cabinet which is designed for professional workshop use. Before
More informationQuickAir - 5, - 10 Minute Emergency Escape Breathing Apparatus. Operating Manual
QuickAir - 5, - 10 Minute Emergency Escape Breathing Apparatus Operating Manual Table of Contents 1 General... 2 1.1 Purpose... 2 1.2 Description... 2 2 Operation... 3 2.1 Pre-donning Inspection... 3 2.1.1
More informationUSER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102
USER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102 THANK YOU FOR CHOOSING YOUR NEW DEHUMIDIFIER. BEFORE USING THE UNIT READ THESE INSTRUCTIONS FULLY AND RETAIN THEM FOR FUTURE REFERENCE
More informationModel MS-41BP 4G/ 15L. WARNING Carefully Read These Instructions Before Use 013529 R0514
Backpack Sprayer Use and Care Manual Model MS-41BP 4G/ 15L WARNING Carefully Read These Instructions Before Use 013529 R0514 WARNING WARNING: Improper use or failure to follow instructions can result in
More informationP6946 WARNING. www.fisher-price.co.uk. Rocker. Swing. IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Infant Seat
P6946 Rocker Swing WARNING IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Infant Seat www.fisher-price.co.uk Consumer Information WARNING To prevent injury or death from falls or being strangled in
More informationMirage FX NASAL MASK. User Guide
Mirage FX NASAL MASK User Guide Mirage FX NASAL MASK Fitting// 1 2 3 4 5 6 Mirage FX i Removal// 1 2 Disassembly// 1 2 3 ii Reassembly// 1 2 3 4 iii Mirage FX A 2 3 1 4 7 6 5 B iv Mask components// Item/
More information758 Heavy-duty Ratchet Guy Wire Cutter
INSTRUCTION MANUAL 758 Heavy-duty Ratchet Guy Wire Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
More informationModular Locomotive System Instruction Manual for HBK8 George Body Kit
Modular Locomotive System Instruction Manual for HBK8 George Body Kit Roundhouse Engineering Co. Ltd. Units 6-10 Churchill Business Park. Churchill Road, Wheatley. Doncaster. DN1 2TF. England. Tel. 01302
More information15GAL STEEL OIL DRAIN WITH 110V PUMP
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
More informationPART 17 SAFETY/RESCUE HARNESS JACKET TYPE M 500/1 BRIGADE ORDER TECHNICAL NO. 13 C O N T E N T S. Page No PURPOSE STRATEGIC AIMS AND OBJECTIVES
PURPOSE C O N T E N T S STRATEGIC AIMS AND OBJECTIVES ROLES, RESPONSIBILITIES AND REVIEW INTRODUCTION Page No 1 1 1 2 BRIGADE ORDER TECHNICAL NO. 13 DESCRIPTION 2 ISSUE/LOCATION 2 USE 3 SAFETY MAINTENANCE
More informationCoolflo Safe Touch Shower Mixing Valve ST20015CP
Coolflo Safe Touch Shower Mixing Valve ST20015CP Installation and Maintenance Instructions In this procedure document we have endeavoured to make the information as accurate as possible. We cannot accept
More informationMirage FX. User Guide. English NASAL MASK
Mirage FX NASAL MASK User Guide English Did you know? Replacing your mask and supplies is one of the most important steps in maintaining effective therapy. Replace when... The cushion is no longer clear
More informationPRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129
PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,
More informationRespiratory Safety and PPE Module 7. Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies
Respiratory Safety and PPE Special Warehouse Worker Hazards in Structural Steel Fabricating and Supply Companies Drawing from OSHA 3384-09 2011 1 Respiratory Safety and PPE OSHA Grant Information This
More informationXL PREMIUM OIL COOLER KIT
-J05 REV. 0-0-0 XL PREMIUM OIL COOLER KIT GENERAL Kit Number 0008 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions
4057250/8 IM-P405-16 AB Issue 8 ABV20 Air Actuated Boiler Blowdown Valve Installation and Maintenance Instructions 1 General safety information 2 General product information 3 Installation 4 Operation
More informationDO NOT attempt to repair hub and wheel bearing assembly.
Page 1 of 6 HUB & WHEEL BEARINGS (WITH PULSE VACUUM HUBLOCK) DO NOT attempt to repair hub and wheel bearing assembly. Removal DO NOT remove hub lock assembly by prying on hub lock legs. This can crack
More informationImportant Information
Single Door Quadrant Instruction Manual ESQ Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to
More informationTriac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
More informationSelf-Contained Breathing Apparatus (SCBA) Program and Procedures for SCOTT AIR-PAK 75i
Self-Contained Breathing Apparatus (SCBA) Program and Procedures for SCOTT AIR-PAK 75i This operating procedure is based on the Manufacture Operating and Maintenance manual for the SCOTT AIR-PAK 75i. Nothing
More information#12 Professional Meat Grinders
#12 Professional Meat Grinders MG-203100 (52021040) Manual Instruction Thank you, and congratulations on purchasing the Non-corrosive electric meat grinder. Your grinder comes complete with everything
More informationBicycoo BMX Instruction Manual 0014X Series
Bicycoo BMX Instruction Manual 0014X Series Joovy 2919 Canton Street Dallas, TX 75226 (877) 456-5049 Fax: (214) 761-1774 Email: customerservice@joovy.com Web Site: www.joovy.com ! WARNINGS Please read
More informationFabric Replacement Top Installation Instructions
Replacement Top Installation Instructions For: Wrangler/YJ 88-95 Part Number: 51120 Special Note: If your Wrangler is a 1986 or 1987 model, this kit is not the correct product. Please order Part Number
More informationKASK HELMET OWNER S USE & CARE MANUAL
KASK HELMET OWNER S USE & CARE MANUAL WARNING Athletic activities involving the use of this equipment are inherently dangerous. You are responsible for your own decisions and actions. Before using this
More informationJust-Like-Mine! Doll or Stuffed Toy. Car Seat. Instruction Manual. These instructions are for the following Joovy Style # s: 002, 003
Just-Like-Mine! Doll or Stuffed Toy Car Seat Instruction Manual These instructions are for the following Joovy Style # s: 002, 003 Please read this instruction manual completely before using your doll
More information10 TON HYDRAULIC PRESS
10 TON HYDRAULIC PRESS Model Nos. CSA10F and CSA10B OPERATING & MAINTENANCE INSTRUCTIONS 0200 SPARE PARTS and SERVICING Please contact your nearest dealer, or CLARKE International, on one of the following
More information1 Important Safety Procedures. Qualified maintenance personnel should read and follow these straightforward instructions.
Installation, Operating and Maintenance Instructions XL Series Actuators Contents Important Safety Procedures Mounting and Operating Instructions Piping Instructions Solenoid Valves on Spring Return Actuators
More informationVW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS
VW GOLF Mk4 TDI FRONT MOUNTING INTERCOOLER INSTALLATION INSTRUCTIONS Tools required: 10mm/13mm socket and 3/8 drive ratchet with extension Torx T20/25/30 screwdrivers or bits Phillips head screwdriver,
More informationCHROME FRONT BRAKE MASTER CYLINDER KIT
-J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder
More informationCORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS
CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS D E F Y I N G C O N V E N T I O N Congratulations on your new Corner Fridge Your new corner fridge may have different functions
More informationFront brakes (FN- 3), servicing
j a t Front brakes (FN- 3), servicing 46-1 Front brakes, servicing Note: Install complete repair kit. After replacing brake pads and before moving vehicle, depress brake pedal several times firmly to properly
More informationINSTALLATION MANUAL MODEL RP-100
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-100 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
More informationCleaning & Sanitisation
Cleaning & Sanitisation Notice: The information and/or procedures presented in the following demonstration(s) should be performed by a trained Water Cooler Service Technician only. Never attempt to service
More informationTWO-WAY DIVERTER WITH THREE-WAY HAND SHOWER
TWO-WAY DIVERTER WITH THREE-WAY HAND SHOWER 1. BEFORE YOU BEGIN A. HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and
More information5800 Temperature Sensor Cable Assembly
5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the
More informationFL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT
-J070 REV. 0-0-0 FL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT GENERAL Kit Number 9-09A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationChill 4 Hole Bath Shower Mixer
Chill 4 Hole Bath Shower Mixer Fitting Instructions & Contents List Please keep these instructions for future reference and request of replacement parts Contents Page 1. Introduction 02 2. Safety Note
More informationWolflite Safety Handlamp H-251E
Wolflite Safety Handlamp H-251E & H-251 Mk1 & Mk2 Wolflite Safety Handlamp H-251E H 18Y H 17 H 31Y H 21A H 30 H 24 H 26 H 19 H 25 H 03 H 15Y H 22 H 104 H 29 H 66 H 13 H 14 H 09 H 12 H 48 H 11 H 62 H 63
More informationModel 2128 AIR COMPRESSOR PUMP Operating Instructions
Model 8 AIR COMPRESSOR PUMP Operating Instructions Assembly of pump Connection to cylinder and charging ) Connect the air hose to the air cylinder and tighten with spanner. Do not over tighten. Note; the
More informationPlease read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Model # 1305TW. Infant car seats not included
Please read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Model # 1305TW Infant car seats not included Double Snap N Go Instruction Manual Convenience through
More informationferroli Boiler Replacement Optimax HE- Modena HE
ferroli Boiler Replacement Optimax HE- Modena HE Introduction The new Ferroli Modena 32C HE high efficiency condensing combination boiler is an ideal replacement for the Ferroli Optimax HE 31 C and the
More informationCarpet Washer. vax.co.uk VRS5W. Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308. Vax model number: Version 1.0
VRS5W Powermax User Guide V1.0.qxd:V1.0 23/7/10 15:35 Page 1 Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308 Carpet Washer Vax model number: VRS5W instruction manual Version 1.0 Please read carefully
More informationRotary IBC AdBlue Pump
Installation, Operating, Maintenance & Safety Instructions Rotary IBC AdBlue Pump RHP105 Important Information It is important to ensure that this pump is both handled and operated in accordance with the
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationUnique DV-ST UltraPure - Manuel: for valve sizes DN8 to DN80 (¼ to 3 )
Instruction Manual Unique DV-ST UltraPure - Manuel: for valve sizes DN8 to DN80 (¼ to 3 ) ESE01752-EN4 2014-02 Original manual Table of contents The information herein is correct at the time of issue
More informationIMPACT SPRINKLER TROUBLESHOOTING GUIDE
RAIN USE AND OPERATION BIRD IMPACT SPRINKLER TROUBLESHOOTING GUIDE The diagrams below depict typical Rain Bird sprinklers with all available controls. Your particular model may have only some of these
More informationInstallation guide Nordic mixer taps. Before installing read this guide first
Installation guide Nordic mixer taps Before installing read this guide first Introduction Installation, maintenance and warranty The Nordic Twintaps are our latest innovation for your kitchen a boiling-water
More informationIMPORTANT INFORMATION
Curved Quadrant Instruction Manual CQ IMPORTANT INFORMATION Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed according to our guidelines.
More informationBILLET HEADLAMP WITH SHORT/TALL MOUNTS
-J099 REV. 00-0- BILLET HEADLAMP WITH SHORT/TALL MOUNTS GENERAL Kit Number 9-0, 9-0 Models Kit 9-0 is a -/ inch headlamp and kit 9-0 is a -/ inch headlamp. Both kits will fit the models listed in Table.
More informationInstructions For SF 6 Refill Kit
S&C Vista Underground Distribution Switchgear UnderCover, Vault-Mounted, and Pad-Mounted Styles Instructions For SF 6 Refill Kit TABLE OF CONTENTS Section Page Section Page INTRODUCTION..................................
More information1. SAFETY RULES. 8. Avoid placing objects in the path of the blades.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationel-720 Carbon Dioxide Gas Leak Detector User s Guide
el-720 Carbon Dioxide Gas Leak Detector User s Guide Congratulations on the purchase of the AccuTools el-720 Carbon Dioxide Gas Leak Detector, the most technologically advanced instrument of its kind.
More informationSALTER AIRE Plus COMPRESSOR Model 8350 / 8352 / 8353. Instruction Manual. Page 1 of 9
SALTER AIRE Plus COMPRESSOR Model 8350 / 8352 / 8353 Instruction Manual Page 1 of 9 TABLE OF CONTENTS Introduction...3 Important Safeguards..3 System Components...5 Setup and Operation...5 Setup...5 Operation....6
More informationLUCCI AIRFUSION QUEST II CEILING FAN
LUCCI AIRFUSION QUEST II CEILING FAN WITH IR REMOTE INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0 QUEST II IR
More informationCHECK WITH LOCAL CODE AUTHORITIES ABOUT INSTALLATION REQUIREMENTS FOR THIS PRODUCT INSTALLATION INSTRUCTIONS
R A-DEC INC. 2601 CRESTVIEW DRIVE POST OFFICE BOX 111 NEWBERG, OREGON 97132 USA TELEPHONE (503)-538-9471 DESIGNATED E.U. REPRESENTATIVE: A-DEC DENTAL U.K., LTD. AUSTIN HOUSE 11 LIBERTY WAY ATTLEBOROUGH
More informationINSTRUCTIONS. FLHR/C/S (Road King) FRONT END LOWERING KIT 1WARNING -J03242 REV. 10-19-04. General. Removal (Left and Right Forks) Kit Number 54614-05
INSTRUCTIONS -J04 REV. 0-9-04 General FLHR/C/S (Road King) FRONT END LOWERING KIT This kit is designed for installation on 00 and later FLHR/C/S Model Motorcycles. Road King models use the conventional
More informationUser Installation Guide
Careline Alarm User Installation Guide 1.1 IMPORTANT INFORMATION The user s telephone MUST BE connected to the Reach TEL socket - a double adapter on the incoming line must not be used. If the user has
More informationInstructions for Using the Watch Works Tool Kit to Change a Watch Battery
Instructions for Using the Watch Works Tool Kit to Change a Watch Battery Click on this link http://www.allamericanwatches.com/site/626101/product/e2306-a to purchase the Watch Battery Replacement Tool
More informationBOBBIN WINDER - TYPES & FUNCTION
BOBBIN WINDER - TYPES & FUNCTION 13.1.006 The bobbin winder is a separate unit screwed on to the machine, adjacent to the balance wheel. Its function is to wind a reserve of cotton evenly onto an empty
More informationM A N U A L 13-10-05
Documentation The following information sheets illustrate the description below: 12-WW01-4G-E Sectional view of the lance with main dimensions 12-W101-6G-E Sectional view of the head of the lance with
More informationINSTALLATION INSTRUCTIONS Fan Coil Replacement Coil Kit EBX & EBXX
Fan Coil Replacement Coil Kit EBX & EBXX These instructions must be read and understood completely before attempting installation. These instructions covers the installation of replacement coil kit into
More informationMP-4V Heavy Duty Riveter / 39048
MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The light weight 3.7 lbs. well balanced MP-4V includes a Vacuum
More informationSBC90. Abrasive Blast Cabinet Assembly & Operating Instructions
SBC90 Abrasive Blast Cabinet Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important
More informationFASCINATION 700 HVLP TANNING PRO SYSTEM USER MANUAL
FASCINATION 700 HVLP TANNING PRO SYSTEM USER MANUAL Congratulations on choosing the Fascination 700 HVLP Tanning Pro System! Your system includes the following items: 1 Fascination 700 HVLP Tanning Pro
More informationSan josé OWNER S MANUAL
San josé OWNER S MANUAL Assembling & operating manual San josé 30 mbar - PORTABLE GAS BARBECUE 1. 2. 3. Improper installation, adjustment, alteration, service or maintenance can injury or property damage.
More informationPOSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT
POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric
More informationEscape Device Range. For a Safe Escape
Escape Device Range For a Safe Escape You have the choice... Emergency escape from hazardous areas and confin ed spaces: the con sidera tion of the options for escape (self-rescue) must be an integral
More informationCaring for Your PleurX Pleural Catheter
Caring for Your PleurX Pleural Catheter A PleurX Pleural Catheter has been placed in your chest through a small incision in your skin into the pleural space (see picture below). This allows you to drain
More informationROTARY TUMBLER INSTRUCTIONS AND PARTS LIST
ROTARY TUMBLER INSTRUCTIONS AND PARTS LIST Model 3-1.5B Model 45C Model 33B LORTONE 12130 Cyrus Way Mukilteo, WA 98275 (425) 493-1600 SETTING UP YOUR MACHINE For 45C Unit Only (33B & 3-1.5B already assembled)
More informationPortable Air Conditioner
Portable Air Conditioner Owner's Manual Model:3 in 1 12,000 Btu/h Series 3 Please read this owner s manual carefully before operation and retain it for future reference. CONTENTS 1. SUMMARY...1 2. PORTABLE
More informationAuto-belay Cable Replacement Process
Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationArtisan Thermostatic bath shower mixer. Fitting Instructions & Contents List
Artisan Thermostatic bath shower mixer Fitting Instructions & Contents List Please keep these instructions for future reference and request of replacement parts Contents Page 1. Introduction 03 2. Specification
More informationContinuous-Flow Supplied Air Respirator
Continuous-Flow Supplied Air Respirator BREATHE-COOL OPERATOR S MANUAL Thank you for choosing the Breathe-Cool Supplied Air Respirator (SAR) system for your respiratory protection needs. At Turbine Products
More informationInstallation Instructions 4508 4508S
SYMPHONY Spread Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. Speed Connect
More information1. CPAP: delivers continuous flow of air at a constant pressure.
What does CPAP stand for? CPAP stands for Continuous Positive Airway Pressure. What does CPAP therapy do? CPAP therapy provides a constant airflow which holds the airway open so that uninterrupted breathing
More information13. REAR WHEEL/BRAKE/SUSPENSION
13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...
More information1.8 CRANKSHAFT OIL SEALS
SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the
More informationHAIR CLIPPER. Model No. HC5150 HC5150 2. 3.
All technical modifications reserved. 09/08. TSC 08.0634 HAIR CLIPPER 2. 3. 1. Model No. HC5150 4. 10/UK/HC5150 Version 03/10 Part No. T22-29458 REMINGTON is a Registered Trade Mark of Spectrum Brands,
More information123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER
123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER Part Number PCD E3 009B MM Rev 1 Nov. 2010 INTRODUCTION The purpose of this manual
More information