Lindab s recommendations
|
|
|
- Cecil King
- 7 years ago
- Views:
Transcription
1 Mounting instruction Suspension of ventilation systems Lindab s recommendations
2 Content General General Examples of suspension Lower requirements of bearing capacity Suspension without requirements of fire class Suspension with requirements of fire class Suspension of circular duct No fire class Fire class R 5 R 30 Suspension of rectangular duct Suspension band 25,25 Threaded rod M8 Suspension band 25 0,90 Suspension band 20 0,70 page Suspension band 25,25 Wire net mat 8 Threaded rod M8 Suspension band 30,00 Wire net mat 0 Threaded rod M8 R60 Threaded rod M0 Wire net mat 2 Suspension band 25, The suspension solutions shown in this pamphlet are based on Swedish practice. This practice is well-tried and developed during many years. The complete suspension is called the "suspension device". This consists of "brackets" and "fasteners". Suspension device Usually divided into: Brackets Fasteners Devices f joining, linking between, bridging linking to. Example: Ceiling bracket, profile, rail, bracket, threaded rod, mounting tape, wire, chain, suspension ring, cradle, bracket including all accessies. Devices f joining, locking fixing in place with. Example: Screw, plug, bolt, nut, washer, rivet, nail. N.B. The suspension device should also include devices that hold the ventilation system from the side suppt it from below, e.g. Lindab's FA, "Bigfoot" and gantry systems such as the "channel framing system" and "Tecstrut". Examples of suspension double-suspended with anch bolts, Suspension bands and self-tapping screws. The function of the suspension apparatus is to keep the ventilation system in place. This function can be divided into various requirements. It may be dimensioned f the of the duct system. It can also be dimensioned to cope with a possible fire and the requirements stipulated accding to the building's classification. Buildings are classified in accdance with the Swedish National Board of Housing, Building and Planning building regulations (BBR 5:2) in three classes (Br, Br2 and Br3). With regard to fire resistance rating of the bearing capacity, this is shown using the letter R followed by a time requirement (5, 30, etc.). A suitable dimensioning of the bearing capacity R is equivalent to the fire resistance of a construction with a through hole e.g. if the construction is rated EI 60, the suspension apparatus should be chosen with a bearing capacity of R 60. No fire class Fire class R 5 Mounting bracket f ventilation duct Threaded rod M8 Suspension band 25 0,90 Suspension band 20 0,70 5 Suspension band 25,25 Wire net mat 8 Threaded rod M8 Suspension band 25,25 Board 2 Threaded rod M8 Suspension band 30,00 Wire net mat 2 Circular ducts single suspended using anch bolt, Z bracket, threaded rod, blade sleeve and suspension ring. Lower requirements of bearing capacity In some cases, the bearing capacity of the suspension device can be reduced. This applies to places where a potentially fallen duct does not to interfere with the openwk construction's overall fire resistance and/ does not reduce protection the spread of combustion gases via the ventilation system. The bearing capacity can then be reduced f example, accding to: R 5 within isolated fire resistant evacuation routes, fan rooms, shafts, linings. This is due to the low fire load there. R 5 in sprinkler areas. R60 R 30 Threaded rod M8 Suspension band 30,00 Board 27 R60 R60 R60 R60 R60 R60 R60 R60 Threaded rod M8 Threaded rod M0 Wire net mat 30 Threaded rod M0 Board 33 EI60 EI60 EI60 2 3
3 Circular duct Uninsulated No fire class Suspension without requirements of fire class The fire requirement f a suspension with regard to emergency services' safety is f all suspensions to cope with at least 300 C f 0 minutes without falling down. The fce in the suspension is caused by the total of the duct and a point load (02 kg) plus any insulation and components (e.g. silencers). The is selected so that the fce does not exceed what the weakest link in the suspension can handle. Suspension with requirements of fire class The fire requirement f a suspension is that all the links in the suspension must meet the required fire class. The fce in the suspension is caused by the total of the duct plus any insulation and components (e.g. silencers). The is selected so that the fce does not exceed what is permitted f the weakest link in the suspension. Approved fastener Rectangular washer Suspension band 25,25 SIS 3 Ø 0,5 / 8,5 /, duct Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 The maximum f hizontal circular ducts is 3 m and 2, m f hizontal rectangular ducts. The reason is that it is inappropriate to have me than one duct joint between the suspension points. F vertical ducts, the maximum distance is 3 m f both circular and rectangular ducts. Suspension distance The maximum f hizontal circular ducts is 3 m and 2, m f hizontal rectangular ducts. The reason is that it is inappropriate to have me than one duct joint between the suspension points. F vertical ducts, the maximum distance is 3 m f both circular and rectangular ducts. Suspension rings and similar should be placed inside the insulation. Suspension distance Suspension band in circumferential loop, folded Rectangular washer Suspension band (2) 25,25 SIS 3 Ø 0,5 / 8,5 /, 2 duct kg Approved fastener Hexagonal nut with flange M8 Z bracket 25 3 Hexagonal nut with flange M8 Suspension distance: Example calculation with single suspension. Suspension distance: Example calculation with single suspension. Threaded rod M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange M8 Blade sleeve M8 Permitted fce in the suspension 700 N Weight Fce Duct 2 kg/m 8 N/m Point load 02 kg 000 N Total 8 N/m Distance, theetical: 700 / 8 =,5 m Permitted fce in the suspension 500 N Weight Fce Duct 2 kg/m 8 N/m 6,5 kg 6 N/m Total 82 N/m Distance 500 / 82 = 2,8 m Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Complete suspension ring, UV SIS 32/FFZV Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M8 Half suspension ring, UVH 2 SIS 32/FFZV Hexagonal nut with flange 2 M8 5
4 Circular duct Uninsulated No fire class Circular duct Uninsulated No fire class Approved fastener Rectangular washer Suspension band 25 0,90 Ø 8,5 / 6,5 /, FFZV, Z275 duct Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Suspension band in circumferential loop, folded duct duct Rectangular washer Suspension band (2) 25 0,90 Ø 8,5 / 6,5 /, FFZV, Z275 Rectangular washer Suspension band (2) 20 0,70 Ø 6,5 / 5,0 / 3, FFZV, Z product None material None density 0 [kg/m³] thickness 0 [mm] Longest 3,0 [m] [type] Suspension band Suspension band Duct Ø Max. permitted load f each pendulum Point load [mm] [kg/m] [m] [m] [m] [m] [m] [m] [m] 63 0,89 3,0 3,0 3,0 3,0 3,0 3,0 3,0 80 0,9 3,0 3,0 3,0 3,0 3,0 3,0 3,0 00, 3,0 3,0 3,0 3,0 3,0 3,0 3,0 2,2 3,0 3,0 3,0 3,0 3,0 3,0 3,0 25, 3,0 3,0 3,0 3,0 3,0 3,0 3,0 0,76 3,0 3,0 3,0 3,0 3,0 3,0 3,0 50,89 3,0 3,0 3,0 3,0 3,0 3,0 3,0 60 2,02 3,0 3,0 3,0 3,0 3,0 3,0 3,0 80 2,26 3,0 3,0 3,0 3,0 3,0 3,0 3, ,56 3,0 3,0 3,0 3,0 3,0 3,0 3,0 22 3,2 3,0 3,0 3,0 3,0 3,0 3,0 3, ,8 3,0 3,0 3,0 3,0 3,0 3,0 3, ,92 3,0 3,0 3,0 3,0 3,0 3,0 3,0 300,20 3,0 3,0 3,0 3,0 3,0 3,0 3,0 35, 3,0 3,0 3,0 3,0 3,0 3,0 3,0 355,96 3,0 3,0 3,0 3,0 3,0 3,0 3,0 00 6,0 3,0 3,0 3,0 3,0 3,0 3,0 3,0 50 8,60 3,0 3,0 3,0 3,0 2, 3,0 3, ,5 3,0 3,0 3,0 3,0 2, 3,0 3, ,2 3,0 3,0 3,0 3,0,7 3,0 3, , 3,0 3,0 3,0 3,0,6 3,0 3, ,0 3,0 3,0 3,0 3,0,7 3,0 3,0 70 5,5 3,0 3,0 3,0 3,0,3 3,0 3, , 3,0 3,0 3,0 3,0,2 3,0 3, ,7 3,0 3,0 3,0 3,0 0,9 3,0 2, , 3,0 3,0 3,0 3,0 0,8 3,0 2, ,0 2,6 3,0 3,0 3,0 0,8 3,0 2, ,2 2, 3,0 3,0 3,0 0,7 3,0 2,0 00 8,0,5 3,0 3,0 3,0 0, 3,0, ,, 3,0 3,0 3,0 0, 2,8, ,8,3 3,0 3,0 3,0 0, 2,6, 6 7
5 Circular duct Insulated EI 5 Fire class R 5 Circular duct Insulated EI 5 Fire class R 5 Approved fastener Rectangular washer Suspension band 25,25 SIS 3 Ø 0,5 / 8,5 /, duct Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Suspension band in circumferential loop, folded Fire insulation Wire net mat 30 mm 00 kg/m³ duct Rectangular washer Suspension band (2) 25,25 SIS 3 Ø 0,5 / 8,5 /, Fire insulation Wire net mat 30 mm 00 kg/m³ Approved fastener Hexagonal nut with flange M8 Z bracket 25 Hexagonal nut with flange M8 Threaded rod M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange M8 Blade sleeve M8 Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Complete suspension ring, UV * SIS 32 / FFZV Fire insulation Wire net mat 30 mm 00 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/electrozinc-plated qual.,6 duct Hexagonal screw with flange 2 M8 Half suspension ring, UVH 2 * SIS 32 / FFZV Hexagonal nut with flange 2 M8 Fire insulation Wire net mat 30 mm 00 kg/m³ * 25, , , ,0 30 * 25, , , ,0 30 product Wire net mat material Rock wool density 00 [kg/m³] thickness 30 [mm] Longest 3,0 [m] [type] Duct 2 2 Ø Max. permitted load f each pendulum [mm] [kg/m] [m] [m] [m] [m] 50 3,87 3,0 3,0 3,0 3,0 60,09 3,0 3,0 3,0 3,0 80,52 3,0 3,0 3,0 3, ,0 3,0 3,0 3,0 3,0 22 6,0 3,0 3,0 3,0 3, ,0 3,0 3,0 3,0 3, ,2 3,0 3,0 3,0 3, ,59 3,0 3,0 3,0 3,0 35 7,9 3,0 3,0 3,0 3, ,87 3,0 3,0 3,0 3,0 00 0,3 3,0 3,0 3,0 3,0 50 3, 3,0 3,0 3,0 3,0 500,8 3,0 3,0 3,0 3, ,0 2,8 3,0 3,0 3, ,3 2,6 3,0 3,0 3, ,5 2,8 3,0 3,0 3, ,8 2,2 3,0 3,0 3, ,5 2,0 3,0 3,0 3, ,7,7 3,0 3,0 3, ,,5 3,0 3,0 3, ,,3 2,7 2,7 3, ,5,2 2, 2, 3,0 00 6,8 0,8,7,7 3, , 0,8,5,5 3, , 0,7,, 2,9 8 9
6 Circular duct Insulated EI 30 Fire class R 30 Circular duct Insulated EI 30 Fire class R 30 Approved fastener Rectangular washer Suspension band 30,0 SIS 2333 Ø 0,5 / 8,5 duct Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Suspension band in circumferential loop, folded Fire insulation Wire net mat 50 mm 00 kg/m³ duct Rectangular washer Suspension band (2) 30,0 SIS 2333 Ø 0,5 / 8,5 Fire insulation Wire net mat 50 mm 00 kg/m³ Approved fastener Hexagonal nut with flange M8 Z bracket 25 Hexagonal nut with flange M8 Threaded rod M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange M8 Blade sleeve M8 Hexagonal screw with flange M8 30 Hexagonal nut with flange M8 Complete suspension ring, UV * SIS 32 / FFZV Fire insulation Wire net mat 50 mm 00 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M8 Half suspension ring, UVH 2 * SIS 32 / FFZV Hexagonal nut with flange 2 M8 Fire insulation Wire net mat 50 mm 00 kg/m³ 2 3 * 25, , , , * 25, , , ,0 30 product Wire net mat material Rock wool density 00 [kg/m³] thickness 50 [mm] Longest 3,0 [m] [type] Duct 2 2 Ø Max. permitted load f each pendulum [mm] [kg/m] [m] [m] [m] [m] 63 0,89 3,0 3,0 3,0 3,0 80 0,9 3,0 3,0 3,0 3,0 00, 3,0 3,0 3,0 3,0 2,2 3,0 3,0 3,0 3,0 25, 3,0 3,0 3,0 3,0 0,76 3,0 3,0 3,0 3,0 50,89 3,0 3,0 3,0 3,0 60 2,02 3,0 3,0 3,0 3,0 80 2,26 3,0 3,0 3,0 3, ,27 3,0 3,0 3,0 3,0 22 8,5 3,0 3,0 3,0 3, ,68 3,0 3,0 3,0 3, ,89 3,0 3,0 3,0 3, ,5 3,0 3,0 3,0 3,0 35 0,9 3,0 3,0 3,0 3, , 3,0 3,0 3,0 3,0 00 3,9 3,0 3,0 3,0 3,0 50 7,2 3,0 3,0 3,0 3, ,0 3,0 3,0 3,0 3, ,6 3,0 3,0 3,0 3, , 3,0 3,0 3,0 3, ,5 3,0 3,0 3,0 3, ,2 3,0 3,0 3,0 3, ,5 3,0 3,0 3,0 3, , 2,7 3,0 2,7 3,0 000, 2,5 3,0 2,5 3,0 20 6,2 2,2 3,0 2,2 3, , 2,0 3,0 2,0 3,0 00 7,6, 2,8, 2, ,5,3 2,7,3 2, ,5,3 2,5,3 2,5 0
7 Circular duct Insulated EI 60 Fire class R 60 Circular duct Insulated EI 60 Fire class R 60 Approved fastener Hexagonal nut with flange M0 Z bracket 25 Hexagonal nut with flange M0 Threaded rod M0 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange M0 Blade sleeve M0 Hexagonal screw with M0 30 flange Hexagonal nut with flange M0 Complete suspension ring, * SIS 32 / FFZV UV Fire insulation Wire net mat 00 mm 00 kg/m³ Hexagonal nut with flange 2 M0 Z bracket 2 25 Hexagonal nut with flange 2 M Threaded rod 2 M0 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M0 Half suspension ring, UVH 2 * SIS 32 / FFZV Hexagonal nut with flange 2 M0 Fire insulation Wire net mat 00 mm 00 kg/m³ 6 * 25, , , , * 25, , , ,0 30 product Wire net mat material Rock wool density 00 [kg/m³] thickness 00 [mm] Longest 3,0 [m] Ø [type] Threaded rod Duct Max. permitted load f each pendulum [mm] [kg/m] [m] [m] 63 0,89 3,0 3,0 80 0,9 3,0 3,0 00, 3,0 3,0 2,2 3,0 3,0 25, 3,0 3,0 0,76 3,0 3,0 50,89 3,0 3,0 60 2,02 3,0 3,0 80 2,26 3,0 3, , 3,0 3,0 22 6,7 3,0 3, ,3 3,0 3, ,0 3,0 3, ,9 3,0 3, ,6 3,0 3, , 3,0 3,0 00 2,9 3,0 3, ,0 3,0 3, ,5 3,0 3, , 2,8 3, ,2 2,7 3, , 2,7 3,0 70, 2,3 3, ,8 2, 3, ,3,8 3, ,8,6 3, ,5,5 3, ,8,3 2, ,3,0 2, ,0, ,9,8 2 3
8 Uninsulated Uninsulated No fire class No fire class duct Rectangular washer Suspension band (2) 25,25 SIS 3 Ø 0,5 / 8,5 /, 8 duct Rectangular washer Suspension band (2) 25 0,90 Ø 8,5 / 6,5 /, FFZV, Z duct Rectangular washer Suspension band 2 25,25 SIS 3 Ø 0,5 / 8,5 /, Self-tapping screws blind rivet Suspension band screwed/riveted,2 3,0 9 9 duct Rectangular washer Suspension band ,90 Ø 8,5 / 6,5 /, Self-tapping screws blind rivet,2 3,0 9 FFZV, Z Suspension band screwed/riveted duct Mounting bracket f ventilation duct 2 Mounting bracket f 2 ventilation duct Self-tapping screws blind rivet Mounting bracket screwed/riveted,2 3, duct Rectangular washer Suspension band (2) 20 0,70 Ø 6,5 / 5,0 / 3, FFZV, Z Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/ electro-zincplated qual.,6 duct Hexagonal nut with flange 2 M8 Channel ( bracket) Rail / Channel on load min. 3 on load duct Rectangular washer Suspension band ,70 Ø 6,5 / 5,0 / 3, Self-tapping screws blind rivet Suspension band screwed/riveted,2 3,0 9 FFZV, Z Hexagonal nut with flange 2 M8 5
9 product material density thickness Longest None None 0 [kg/m³] 0 [mm] 2, [m] Suspension band mounting bracket Uninsulated No fire class [type] Threaded rod Suspension band Duct Max. permitted load f each pendulum Point load [mm] [mm] [m] [kg/m] [m] [m] [m] [m] ,6,29 2, 2, 2, 2, ,7,98 2, 2, 2, 2, ,8 5,68 2, 2, 2, 2, ,7,98 2, 2, 2, 2, ,8 5,68 2, 2, 2, 2, ,9 6,37 2, 2, 2, 2, ,0 7,06 2, 2, 2, 2, ,8 5,68 2, 2, 2, 2, ,9 6,37 2, 2, 2, 2, ,0 7,06 2, 2, 2, 2, , 7,75 2, 2, 2, 2, ,2 8,5 2, 2, 2, 2, 00 00,0 7,06 2, 2, 2, 2, 00 50, 7,75 2, 2, 2, 2, ,2 8,5 2, 2, 2, 2, ,3 9, 2, 2, 2, 2, , 9,83 2, 2, 2, 2, 00 00,6,2 2, 2, 2, 2, ,3 9, 2, 2, 2, 2, , 9,83 2, 2, 2, 2, ,5 0,5 2, 2, 2, 2, ,6,2 2, 2, 2, 2, ,8 2,6 2, 2, 2, 2, ,0,0 2, 2, 2, 2, ,5 0,5 2, 2, 2, 2, ,6,2 2, 2, 2, 2, ,7,9 2, 2, 2, 2, ,8 2,6 2, 2, 2, 2, ,0,0 2, 2, 2, 2, ,2 5, 2, 2, 2, 2, , 6,8 2, 2, 2, 2, ,0,9 2, 2, 2, 2, , 5,6 2, 2, 2, 2, ,2 6,3 2, 2, 2, 2, , 7,7 2, 2, 2, 2, ,6 9, 2, 2, 2, 2, ,8 20,6 2, 2, 2, 2, ,2 25,0 2, 2, 2, 2, Suspension band mounting bracket [type] Threaded rod Suspension band Duct Max. permitted load f each pendulum Point load [mm] [mm] [m] [kg/m] [m] [m] [m] [m] ,5 8,6 2, 2, 2, 2, ,6 9,3 2, 2, 2, 2, ,8 20,7 2, 2, 2, 2, ,0 22, 2, 2, 2, 2, ,2 23,6 2, 2, 2, 2, ,6 28,0 2, 2, 2, 2, ,0 3,0 2, 2, 2, 2, ,0 22,3 2, 2, 2, 2, ,2 23,7 2, 2, 2, 2, , 25, 2, 2, 2, 2, ,6 26,6 2, 2, 2, 2, ,0 3,0 2, 2, 2, 2, , 3,0 2, 2, 2,, ,8 37, 2, 2, 2,, ,6 26,7 2, 2, 2, 2, ,8 28, 2, 2, 2, 2, ,0 29,6 2, 2, 2, 2, , 3,0 2, 2, 2,, ,8 37,0 2, 2, 2,, ,2 0, 2, 2, 2,, ,6 3, 2, 2, 2,, ,0 33, 2, 2, 2,, ,2 3,8 2, 2, 2,, , 36,2 2, 2, 2,, ,8 0,8 2, 2, 2,, ,2 3,8 2, 2, 2,, ,6 6,8 2,3 2, 2,, ,0 9,8 2,3 2, 2,, , 58,0 2,2 2, 2,, ,6 38,3 2, 2, 2,, ,8 39,6 2, 2, 2,, ,2,3 2, 2, 2,, ,6 7,3 2, 2, 2,, ,0 50,3 2, 2, 2,, , 53,3 2, 2, 2,, ,8 6,5 2, 2, 2,3, ,2 65,0 2, 2, 2,2 0, ,0 0,6 2, 2, 2,, ,2 2,3 2, 2, 2,, ,6 5,5 2, 2, 2,, ,0 8,7 2, 2, 2,, , 52,0 2, 2, 2,, ,8 55,3 2, 2, 2,, ,2 62, 2, 2, 2,3, ,6 65,3 2, 2, 2,2 0, ,0 68,5 2, 2, 2, 0,9 6 7
10 Insulated EI 5 with wire net mat Fire class R 5 Insulated EI 5 with wire net mat Fire class R 5 duct Rectangular washer Suspension band (2) 25,25 SIS 3 Ø 0,5 / 8,5 /, Fire insulation Wire net mat 0 mm 00 kg/m³ duct Rectangular washer Suspension band 2 25,25 SIS 3 Ø 0,5 / 8,5 /, Self-tapping screws blind rivet Suspension band screwed/riveted,2 3,0 9 Fire insulation Wire net mat 0 mm 00 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 duct Hexagonal nut with flange 2 M8 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M8 Fire insulation Wire net mat 0 mm 00 kg/m³ product Wire net mat material Rock wool density 00 [kg/m³] thickness 0 [mm] Longest 2, [m] [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,6 7,33 2, 2, ,7 8,2 2, 2, ,8 9,52 2, 2, ,7 8,2 2, 2, ,8 9,52 2, 2, ,9 0,6 2, 2, ,0,7 2, 2, ,8 9,52 2, 2, ,9 0,6 2, 2, ,0,7 2, 2, , 2,8 2, 2, ,2 3,9 2, 2, 00 00,0,7 2, 2, 00 50, 2,8 2, 2, ,2 3,9 2, 2, ,3 5,0 2, 2, , 6, 2, 2, 00 00,6 8,3 2, 2, ,3 5,0 2, 2, , 6, 2, 2, ,5 7,2 2, 2, ,6 8,3 2, 2, ,8 20, 2, 2, ,0 22,6 2, 2, ,5 7,2 2, 2, ,6 8,3 2, 2, ,7 9,3 2, 2, ,8 20, 2, 2, ,0 22,6 2, 2, ,2 2,8 2, 2, , 27,0 2, 2, ,0 23,6 2, 2, , 2,6 2, 2, ,2 25,7 2, 2, , 27,9 2, 2, ,6 30, 2, 2, ,8 32, 2, 2, ,2 38, 2, 2, 8 9
11 [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,5 29,2 2, 2, ,6 30,3 2, 2, ,8 32,5 2, 2, ,0 3,7 2, 2, ,2 37,0 2, 2, ,6 3,0 2, 2, ,0 7,6 2, 2, ,0 3,9 2, 2, ,2 37, 2, 2, , 39,3 2, 2, ,6,6 2, 2, ,0 7,6 2, 2, , 52,2 2,0 2, ,8 57,0,8 2, ,6,7 2, 2, ,8 3,9 2,3 2, ,0 6,2 2,2 2, , 52,2 2,0 2, ,8 56,8,8 2, ,2 6,6,7 2, ,6 66,2,5 2, ,0 50,0 2,0 2, ,2 52,2 2,0 2, , 5,,9 2, ,8 60,7,7 2, ,2 65,3,6 2, ,6 69,9,5 2, ,0 7,5, 2, , 8,3,2 2, ,6 57,3,8 2, ,8 59,5,7 2, ,2 65,7,6 2, ,6 70,3, 2, ,0 7,9, 2, , 79,5,3 2, ,8 89,3, 2, ,2 9,, 2, ,0 6,3,7 2, ,2 63,7,6 2, ,6 68,5,5 2, ,0 73,, 2, , 78,2,3 2, ,8 83,2,2 2, ,2 9,5, 2, ,6 96,3, 2, ,0 0,0 2,0 duct Insulated EI 5 with board Fire class R 5 Rectangular washer Suspension band (2) 25,25 SIS 3 Ø 0,5 / 8,5 /, Fire insulation Board 30 mm 50 kg/m³ duct Rectangular washer Suspension band 2 25,25 SIS 3 Ø 0,5 / 8,5 /, Self-tapping screws blind rivet Suspension band screwed/riveted,2 3,0 9 Fire insulation Board 30 mm 50 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 duct Hexagonal nut with flange 2 M8 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M8 Fire insulation Board 30 mm 50 kg/m³
12 product material Rock wool density 50 [kg/m³] thickness 30 [mm] Longest 2, [m] Board [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,6 7,53 2, 2, ,7 8,67 2, 2, ,8 9,82 2, 2, ,7 8,67 2, 2, ,8 9,82 2, 2, ,9,0 2, 2, ,0 2, 2, 2, ,8 9,82 2, 2, ,9,0 2, 2, ,0 2, 2, 2, , 3,2 2, 2, ,2, 2, 2, 00 00,0 2, 2, 2, 00 50, 3,2 2, 2, ,2, 2, 2, ,3 5,5 2, 2, , 6,7 2, 2, 00 00,6 9,0 2, 2, ,3 5,5 2, 2, , 6,7 2, 2, ,5 7,8 2, 2, ,6 9,0 2, 2, ,8 2,2 2, 2, ,0 23,5 2, 2, ,5 7,8 2, 2, ,6 9,0 2, 2, ,7 20, 2, 2, ,8 2,2 2, 2, ,0 23,5 2, 2, ,2 25,8 2, 2, , 28, 2, 2, ,0 2,5 2, 2, , 25,6 2, 2, ,2 26,7 2, 2, , 29,0 2, 2, ,6 3,3 2, 2, ,8 33,7 2, 2, ,2 39,9 2, 2, Insulated EI 5 with board Fire class R [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,5 30, 2, 2, ,6 3,5 2, 2, ,8 33,8 2, 2, ,0 36, 2, 2, ,2 38,5 2, 2, ,6,7 2,3 2, ,0 9,5 2, 2, ,0 36,3 2, 2, ,2 38,6 2, 2, , 0,9 2, 2, ,6 3,3 2, 2, ,0 9,5 2, 2, , 5,3,9 2, ,8 59,3,7 2, ,6 3, 2,3 2, ,8 5,7 2,2 2, ,0 8, 2, 2, , 5,3,9 2, ,8 59,,7 2, ,2 6,,6 2, ,6 68,9,5 2, ,0 5,9 2,0 2, ,2 5,2,9 2, , 56,5,8 2, ,8 63,0,6 2, ,2 67,8,5 2, ,6 72,6, 2, ,0 77,,3 2, , 87,,2 2, ,6 59,5,7 2, ,8 6,8,6 2, ,2 68,2,5 2, ,6 73,0, 2, ,0 77,8,3 2, , 82,6,2 2, ,8 92,6, 2, ,2 97,9,0 2, ,0 63,7,6 2, ,2 66,2,5 2, ,6 7,2, 2, ,0 76,3,3 2, , 8,0,3 2, ,8 86,5,2 2, ,2 95,0, 2, ,6 00,0 2, ,0 05,0,
13 Insulated EI 30 with wire net mat Fire class R Insulated EI 30 with wire net mat Fire class R 30 duct Rectangular washer Suspension band (2) 30,0 SIS 2333 Ø 0,5 / 8,5 Fire insulation Wire net mat 70 mm 00 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M8 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M8 Fire insulation Wire net mat 70 mm 00 kg/m³ product Wire net mat material Rock wool density 00 [kg/m³] thickness 70 [mm] Longest 2, [m] [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,6 0,5 2, 2, ,7,8 2, 2, ,8 3,2 2, 2, ,7,8 2, 2, ,8 3,2 2, 2, ,9,6 2, 2, ,0 6,0 2, 2, ,8 3,2 2, 2, ,9,6 2, 2, ,0 6,0 2, 2, , 7, 2, 2, ,2 8,8 2, 2, 00 00,0 6,0 2, 2, 00 50, 7, 2, 2, ,2 8,8 2, 2, ,3 20,2 2, 2, , 2,6 2, 2, 00 00,6 2, 2, 2, ,3 20,2 2, 2, , 2,6 2, 2, ,5 23,0 2, 2, ,6 2, 2, 2, ,8 27,2 2, 2, ,0 29,9 2, 2, ,5 23,0 2, 2, ,6 2, 2, 2, ,7 25,8 2, 2, ,8 27,2 2, 2, ,0 29,9 2, 2, ,2 32,7 2, 2, , 35,5 2, 2, ,0 30,9 2, 2, , 32,3 2, 2, ,2 33,7 2, 2, , 36, 2, 2, ,6 39,2 2, 2, ,8 2,2 2, 2, ,2 9,3 2, 2, 2 25
14 32 33 [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,5 38, 2, 2, ,6 39,5 2, 2, ,8 2,2 2, 2, ,0 5,0 2, 2, ,2 8,0 2, 2, ,6 55, 2, 2, ,0 60,9 2, 2, ,0 5,3 2, 2, ,2 8,0 2, 2, , 50,8 2, 2, ,6 53,8 2, 2, ,0 60,9 2, 2, , 66,7 2, 2, ,8 72,7 2, 2, ,6 53,8 2, 2, ,8 56,6 2, 2, ,0 59,6 2, 2, , 66,7 2, 2, ,8 72,5 2, 2, ,2 78,5 2, 2, ,6 8,3 2, 2, ,0 63, 2, 2, ,2 66,2 2, 2, , 68,9 2, 2, ,8 76, 2, 2, ,2 82,2 2, 2, ,6 88,0 2,3 2, ,0 93,8 2,2 2, , 05,9, ,6 72, 2, 2, ,8 75,2 2, 2, ,2 82,7 2, 2, ,6 88,5 2,3 2, ,0 9,3 2,2 2, , 00 2,0 2, ,8,8, ,2 7,7, ,0 77,6 2, 2, ,2 80,6 2, 2, ,6 86,7 2, 2, ,0 92,7 2,2 2, , 98,7 2, 2, ,8 05,9, ,2,8, ,6 20,7, ,0 26,6,6 duct Insulated EI 30 with board Fire class R 30 Rectangular washer Suspension band (2) 30,0 SIS 2333 Ø 0,5 / 8,5 Fire insulation Board 60 mm 50 kg/m³ Hexagonal nut with flange 2 M8 Z bracket 2 25 Hexagonal nut with flange 2 M8 Threaded rod 2 M8 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M8 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M8 Fire insulation Board 60 mm 50 kg/m³
15 product material Rock wool density 50 [kg/m³] thickness 60 [mm] Longest 2, [m] Board [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,6,9 2, 2, ,7 3, 2, 2, ,8 5,0 2, 2, ,7 3, 2, 2, ,8 5,0 2, 2, ,9 6,6 2, 2, ,0 8,2 2, 2, ,8 5,0 2, 2, ,9 6,6 2, 2, ,0 8,2 2, 2, , 9,8 2, 2, ,2 2, 2, 2, 00 00,0 8,2 2, 2, 00 50, 9,8 2, 2, ,2 2, 2, 2, ,3 23,0 2, 2, , 2,6 2, 2, 00 00,6 27,8 2, 2, ,3 23,0 2, 2, , 2,6 2, 2, ,5 26,2 2, 2, ,6 27,8 2, 2, ,8 3,0 2, 2, ,0 3, 2, 2, ,5 26,2 2, 2, ,6 27,8 2, 2, ,7 29, 2, 2, ,8 3,0 2, 2, ,0 3, 2, 2, ,2 37,3 2, 2, , 0,5 2, 2, ,0 35, 2, 2, , 36,7 2, 2, ,2 38,3 2, 2, ,, 2, 2, ,6,6 2, 2, ,8 8,0 2, 2, ,2 55,9 2, 2, Insulated EI 30 with board Fire class R [type] Duct 2 2 Max. permitted load f each pendulum [mm] [mm] [m] [kg/m] [m] [m] ,5 3,3 2, 2, ,6,9 2, 2, ,8 8,0 2, 2, ,0 5,2 2, 2, ,2 5,6 2, 2, ,6 62,5 2, 2, ,0 69, 2, 2, ,0 5,5 2, 2, ,2 5,6 2, 2, , 57,8 2, 2, ,6 6,2 2, 2, ,0 69, 2, 2, , 75,7 2, 2, ,8 82,5 2, 2, ,6 6,2 2, 2, ,8 6, 2, 2, ,0 67,8 2, 2, , 75,7 2, 2, ,8 82,3 2, 2, ,2 89, 2,3 2, ,6 95,7 2, 2, ,0 7,6 2, 2, ,2 7,8 2, 2, , 77,9 2, 2, ,8 86,2 2, 2, ,2 92,8 2,2 2, ,6 99, 2, 2, ,0 06,9, , 8,7, ,6 8,8 2, 2, ,8 85,0 2, 2, ,2 93,3 2,2 2, ,6 00 2,0 2, ,0 06,9, , 3,8, ,8 25,6, ,2 32,5, ,0 87,8 2,3 2, ,2 9,2 2,2 2, ,6 98, 2, 2, ,0 05,9, , 2,8, ,8 9,7, ,2 29,6, ,6 36,5, ,0 3,, 28 29
16 Insulated EI 60 with wire net mat Fire class R 60 Insulated EI 60 with wire net mat Fire class R 60 Hexagonal nut with flange 2 M0 Z bracket 2 25 Hexagonal nut with flange 2 M0 Threaded rod 2 M0 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M0 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M0 Fire insulation Wire net mat 0 mm 00 kg/m³ 36 product Wire net mat material Rock wool density 00 [kg/m³] thickness 0 [mm] Longest 2, [m] [type] Threaded rod Duct 2 36 Max. permitted load f each pendulum 000 [mm] [mm] [m] [kg/m] [m] ,6 20,5 2, ,7 22,6 2, ,8 2,7 2, ,7 22,6 2, ,8 2,7 2, ,9 26,8 2, ,0 28,9 2, ,8 2,7 2, ,9 26,8 2, ,0 28,9 2, , 3,0 2, ,2 33, 2, 00 00,0 28,9 2, 00 50, 3,0 2, ,2 33, 2, ,3 35,2 2, , 37,3 2, 00 00,6,5 2, ,3 35,2 2, , 37,3 2, ,5 39, 2, ,6,5 2, ,8 5,6 2, ,0 9,8 2, ,5 39, 2, ,6,5 2, ,7 3,5 2, ,8 5,6 2, ,0 9,8 2, ,2 5,0 2, , 58,2 2, ,0 50,8 2, , 52,8 2, ,2 5,9 2, , 59, 2, ,6 63,3 2, ,8 67,6 2, ,2 77,6 2, 30 3
17 [type] Threaded rod Duct 2 Max. permitted load f each pendulum 000 [mm] [mm] [m] [kg/m] [m] ,5 6, 2, ,6 63,5 2, ,8 67,7 2, ,0 7,9 2, ,2 76,2 2, ,6 86,2 2, ,0 9,8 2, ,0 72, 2, ,2 76,3 2, , 80,5 2, ,6 8,8 2, ,0 9,8 2, , 03 2, ,8 2, ,6 8,9 2, ,8 89, 2, ,0 93, 2, , 03 2, ,8 2, ,2 2, ,6 29, ,0 97,2 2, ,2 0 2, , 06, ,8 6, ,2 2, ,6 33, ,0 2, , 55, ,6 0, ,8 5, ,2 25, ,6 3, ,0 2, , 5, ,8 65, ,2 7, ,0 8, ,2 23, ,6 32, ,0, , 9, ,8 58, ,2 7, ,6 80, ,0 88, 36 Insulated EI 60 with board Fire class R 60 Hexagonal nut with flange 2 M0 Z bracket 2 25 Hexagonal nut with flange 2 M0 Threaded rod 2 M0 Bright/electrozinc-plated qual.,6 duct Hexagonal nut with flange 2 M0 Channel ( bracket) Rail / Channel on load min. 3 on load 2 3 Hexagonal nut with flange 2 M0 Fire insulation Board 20 mm 50 kg/m³
18 product material Rock wool density 50 [kg/m³] thickness 20 [mm] Longest 2, [m] Board [type] Threaded rod Duct 2 Max. permitted load f each pendulum 000 [mm] [mm] [m] [kg/m] [m] ,6 23,7 2, ,7 26,2 2, ,8 28,7 2, ,7 26,2 2, ,8 28,7 2, ,9 3,2 2, ,0 33,7 2, ,8 28,7 2, ,9 3,2 2, ,0 33,7 2, , 36,2 2, ,2 38,7 2, 00 00,0 33,7 2, 00 50, 36,2 2, ,2 38,7 2, ,3,2 2, , 3,7 2, 00 00,6 8,7 2, ,3,2 2, , 3,7 2, ,5 6,2 2, ,6 8,7 2, ,8 53,6 2, ,0 58,6 2, ,5 6,2 2, ,6 8,7 2, ,7 5, 2, ,8 53,6 2, ,0 58,6 2, ,2 63,6 2, , 68,6 2, ,0 59,6 2, , 62,0 2, ,2 6,5 2, , 69,5 2, ,6 7,5 2, ,8 79,6 2, ,2 9,2 2,2 37 Insulated EI 60 with board Fire class R 60 [type] Threaded rod Duct 2 37 Max. permitted load f each pendulum 000 [mm] [mm] [m] [kg/m] [m] ,5 72,2 2, ,6 7,7 2, ,8 79,7 2, ,0 8,7 2, ,2 89,8 2, ,6 0 2, ,0 2, ,0 8,9 2, ,2 89,9 2, , 9,9 2, ,6 00 2, ,0 2, , 22, ,8 32, ,6 00 2, ,8 05, ,0 0, , 22, ,8 32, ,2 2, ,6 53, ,0, ,2 9, , 2, ,8 36, ,2 6, ,6 56, ,0 66, , 82, ,6 30, ,8 35, ,2 7, ,6 57, ,0 67, , 77, ,8 93, ,2 203, ,0 39, ,2 5, ,6 55, ,0 65, , 76, ,8 86, ,2 200, ,6 2, ,0 22 0,9 3 35
lindab duct suspension & support system Duct suspensions & Support systems
lindab duct suspension & support Duct suspensions & Support s lindab duct suspension & support Content Duct suspensions & Support s Duct suspension Duct suspension FB... DRSN... 0 DRSNR... 0 Channels and
Isover HVAC Application Handbook Installing fire protection insulation to metal ductwork
Isover HVAC Application Handbook Installing fire protection insulation to metal ductwork HVAC - Fire protection of metal ductwork Fire protection Thermal insulation Isover ULTIMATE TM Protect - Fire protection
Installation information. METTLER TOLEDO MultiRange DW150 / DW150T wall scale
Installation information METTLER TOLEDO MultiRange DW150 / DW150T wall scale DW150 / DW150T wall scale Contents Contents Page 1. Installation... 2 1.1 Preparatory work... 2 1.2 Installing the wall plates
lindab duct suspension & support system Duct suspensions & Support systems
lindab duct suspension & support system Duct suspensions & Support systems lindab duct suspension & support system Content Duct suspensions & Support systems Duct suspension Threaded rod OSB 0... Channels
PITCHED ROOF STRUCTURES
PITCHED ROOF STRUCTURES for framed and frameless photovoltaic modules Needed tools and materials: cordless screwdriver 10mm and 13mm spanners 5mm Allen key bolts, screws and tools for fixing the system
TFSR & TFSK Roof Fans
Fans Air Handling Units Air Distribution Products Fire Safety Air Conditioning Air Curtains and Heating Products Tunnel Fans TFSR & TFSK Roof Fans With swing-out function 2 I TFSR/TFSK TFSR & TFSK Roof
INSTALLATION INSTRUCTIONS AIRCOMMAND IBIS ROOFTOP AIRCONDITIONER
\ INSTALLATION INSTRUCTIONS AIRCOMMAND IBIS ROOFTOP AIRCONDITIONER Suitability: The IBIS caravan rooftop aircondioner is suitable for installation on caravans and motorhomes provided the roof structure
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5 www.thomsonlinear.com Version History Edition Number Edition Date Reason for Revision 1 2004 First edition
Chapter 73 Articles of iron or steel
Notes. Chapter 73 Articles of iron or steel 1.- In this Chapter the expression cast iron applies to products obtained by casting in which iron predominates by weight over each of the other elements and
Pipe Clamps and Accessories
Products 4.0 Products 4.1 Connection options to pipe clamps with Triple-Thread Connector NT 3G (M16, M10, M8) 4.2 Connection options to pipe clamps with Triple-Thread Connector NT 3G (3/8", M12, M10) 4.3
Nuffield and Middleweight Leyland Tractor - 11 inch - Double Clutch Overhaul Part 1 - Clutch Removal and Dismantling
Nuffield and Middleweight Leyland Tractor - 11 inch - Double Clutch Overhaul Part 1 - Clutch Removal and Dismantling Due to the many different configurations of cabed and non-cabed tractors this article
Installation information. METTLER TOLEDO MultiRange Floor scales / Pit scales
Installation information METTLER TOLEDO MultiRange Floor scales / Pit scales KC300/KCS300 KC600/KCS600 KD600/KD1500 KE1500/KE3000 KES1500/KES3000 KG3000/KG6000 KN1500 Floor scales / Pit scales Contents
WTW SWANTM. Linear slot air diffusers of wall-to-wall design for ceilings
SWANTM WTW Linear slot air diffusers of wall-to-wall design for ceilings Quick facts Wall-to-wall installation Diffuser face of light aluminium design 2, 3 or slots Horizontal/vertical air distribution
Services Enclosures and Protected Shafts - Maintaining Compartmentation
Introduction When a fire resisting element is used to provide fire compartmentation, every opening that allows services to pass through the element must be adequately protected by sealing, or fire stopping
PRS X-axis E-chain installation: For tools with a 12 Z-Axis
PRS X-axis Energy Chain (Echain) Installation Page -1- PRS X-axis E-chain installation: For tools with a 12 Z-Axis This kit is compatible with PRS Shopbots that have an X-axis cutting area of 96 to 144.
Accessory Manual Ventilation Section Model Comfort Circle
Accessory Manual Ventilation Section Model Comfort Circle Manual version:. R a Copyright and trademarks All the information and drawings in this manual are the property of Biddle and may not be used (other
SECTION 15140 - PIPE HANGERS AND SUPPORTS
Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the
FLEXIT S3 X/TT A3 X/TT K3 X/TT S3 R S3 RK
944E-05 006-0 FLEXIT S X/TT A X/TT K X/TT S R S RK Installation Instructions Air Handling Unit/ Kitchen Model S X/TT K X/TT A X/TT S R S RK Air handling unit with cross heat exchangeror TT exchanger Air
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08. Linear Motion and Assembly Technologies
STAR Linear Bushings and Shafts Supplement RE 83 117/2001-08 Linear Motion and Assembly Technologies STAR Linear Motion Technology Ball Rail Systems Standard Ball Rail Systems Ball Rail Systems with Aluminum
1.2.1 1.1.8 PRODUCTBLADEN GT ROCKPANEL STRUCTURE
1..1 1.1.8 PRODUCTBLADEN SHEETS GT page 1 to 6 Rockpanel Structure is a very durable panel with a lightly textured finish, specially developed for use in cladding, fascia, soffit applications. The basic
9300BC SERIES Light Commercial Door Closer
Light Commercial Door Closer general information The 9300BC is a durable, economically priced door closer designed for commercial exterior and interior doors such as storefront and industrial applications.
Flamco Stainless steel mountings
S TA I N L E S S S T E E L M O U N T I N G S 9 Flamco Stainless steel mountings BRS-A BSF - SS RAIL R - SS GP - SS Edition 2007 / UK Stainless steel mountings Flamco offers the best attachment options
Table of contents CAT DISC 25. Mower
Mower CAT DISC 25 ( Type PTM 370 : +.. 01001 ) Excerpt from operating manual Nr. 0370B00C.pdf Table of contents Swath Discs... 13 Swath Boards... 13 Safety points... 14 General maintenance hints... 14
BUILD A TABLETOP LOOM
BUILD A TABLETOP LOOM From 1" x 2" stock (actual 3/4" x 1"1/2) cut: 4 pieces 15" long 4 pieces 5"1/2 long Use the above to make 2 frames for the front and back of the loom. From 1" x 4" stock (actual 3/4"
1993 SUSPENSION Volkswagen Front. EuroVan
Article Text ARTICLE BEGINNING 1993 SUSPENSION Volkswagen Front EuroVan DESCRIPTION FWD independent suspension is an double-wishbone type with torsion bars mounted on upper control arm. Wheel is supported
Installation Manual. BYD Wall-mounted AC Charging Box
Installation Manual BYD Wall-mounted AC Charging Box BYD Wall-mounted AC Charging Box Installation Manual Version/Revision: A/0 Dedicated Service Commitment from BYD Auto Dear valuable customers: We are
TECHNICAL INFORMATION
TECHNICAL INFORMATION Models No. 2012NB Description 304mm (12") Automatic Thickness Planer CONCEPTION AND MAIN APPLICATIONS * Compact and light weight (27 Kg./59 lbs) automatic thickness planer for easier
Défumair XR. ventilation and cmv. fire grade - label CE. smoke-extraction fan extraction casing for kitchen at F400-120. advantages.
Défumair XR smoke-extraction fan extraction casing for kitchen at F400-120 Personalisation : - Phonic insulation version by insulated double-skin panels through 25 mm glass wool, class M1. advantages Originally
INSTALLATION INSTRUCTIONS: Viewline 85 mm
1-10 1 Safety information The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of-the-art technology. The unit is designed for use
Fire Test Laboratory
EFECTIS ERA AVRASYA Fire Test Laboratory Accredited Body No: AB-0556-T CLASSIFICATION OF FIRE RESISTANCE PERFORMANCE IN ACCORDANCE WITH EN 13501-2:2007+A1:2009 Sponsor : ÖZBOSAN OTOMATİK KAPI VE KEPENK
INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES. Interpretations of the FTP
INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES Interpretations of the FTP CONTENTS FTP1 Adhesives used in A or B class divisions (FTP Code 3.1, Res A.754 para. 3.2.3) June 2000 FTP2 Pipe and duct
MONDOATHENS BASKETBALL SET (Reference PK110)
MONDOATHENS BASKETBALL SET (Reference PK110) DESCRIPTION The MONDOATHENS backstop unit is mainly designed for multi-sports pavilions and installations where the highest-level basketball competitions are
Mounting instructions for SOT78 (TO-220AB); SOT186A (TO-220F)
Mounting instructions for SOT78 (TO-220AB); SOT186A (TO-220F) Rev. 1 29 May 2012 Application note Document information Info Keywords Abstract Content SOT78; SOT186A; TO-220AB; TO-220F This application
General Allowances for Insulation & Cladding
TRADE OF Industrial Insulation PHASE 2 Module 1 Sheet Metal and Insulation Fundamentals UNIT: 4 General Allowances for Insulation & Cladding Produced by In cooperation with subject matter expert: Michael
Incorporating V2.3. Product spec >>> > Series ECG - Egg Crate Grilles. > Series ECG45-45 Egg Crate Grilles
Incorporating V2.3 Product spec >>> > Series ECG - Egg Crate Grilles > Series ECG45-45 Egg Crate Grilles Grilles Egg crate Recommended for: Wall, ceiling & duct Extract Overview Industry standard extract
BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
Page 1 of 21 Product Information Baja Web > Product Information > Parts Lists > GOKART > BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM) BR150 Pmi Baja Reaction 150cc Go Kart (VIN PREFIX L4VM)
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast Anchor version HUS-A 6 Screw with hex head HUS-H 6 Screw with hex head HUS-I 6 Screw with hex head Benefits - Quick and easy setting - Low
TPM 006/99 Revision 1 VALID FROM: 8/2/2013 REPLACEMENT FOR TPM 006/99 FIRE SHUTTER
Revision 1 VALID FROM: 8/2/2013 REPLACEMENT FOR TPM 006/99 FIRE SHUTTER PSUM These technical specifications determinate a range of manufactured sizes and models of fire shutters (further only shutters)
Guide rail bracket (for adjustable heads)
(for adjustable heads) Part. 209 40 ø,5 ø10,5 2 2,5 115 15 42 5 11 37 72 4 70 Code 209 / 0754 MATERIALS: Bracket made out of reinforced polyamide black colour. FEATURES: To be used with heads Part.221,
SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 29 - HANGERS AND SUPPORTS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe hangers and supports. 2. Hanger rods. 3. Inserts. 4. Flashing. 5. Equipment
INSTALLATION INSTRUCTIONS. 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113)
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
StorMax Cable and Interconnect Installation Instructions
StorMax Cable and Interconnect Installation Instructions 1 StorMax Cable and Interconnect Installation Instructions StorMax Cable and Interconnect Installation Instructions... 2 Welcome to the StorMax
Formwork Direct International Ltd Phone No +44 (0151) 532 0179 Fax no +44 (0151) 523 8330 E-Mail: sales@formworkdirect.co.
Tie Rod & Formwork s well as containing our comprehensive range of Formwork Tie Sytems; this section also covers our market leading Rapidobat Column Former. Exclusive also to Formwork Direct are innovations
Code Compliance for Spring Steel Fasteners Based on the 2005 NEC
Code Compliance for Spring Steel Fasteners Based on the 2005 NEC B-Line has recognized the need for a reference source, detailing the National Electrical Code requirements for Spring Steel Fasteners. The
Puddle Flange. FRANK Puddle Flange
Puddle Flange FRANK Puddle Flange The problem Problems keep on occurring when connecting pipes during construction work. Pipes laid in the ground must be introduced into concrete walls or shafts. In many
INSTALLATION INSTRUCTIONS. 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD IMPORTANT NOTES
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS
SYSTEM COMPONENTS PREASSEMBLED ELEMENTS FOR FIFTING AND SLIDING DOORS s r ood gn i d i l s dna gn i t f i f r o f s t neme l e de l bme s s ae r P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS These
INSTALLATION INSTRUCTIONS: Viewline 52 mm
-5 Safety information The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of-the-art technology. The instrument is designed for use
AM/FM ANTENNA RELOCATION KIT
-J0 REV. 008-09-0 AM/FM ANTENNA RELOCATION KIT GENERAL Kit Number 766-09 Models This kit is used to relocate a fender-mounted AM/FM antenna to a Detachable Tour-Pak on specific model motorcycles. For model
INSTRUCTIONS: LocknCharge Laptop Carts
INSTRUCTIONS: LocknCharge Laptop Carts www.lockncharge.com Extra Tools required: Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied) (Panel colours for illustration purposes
FSD35, FSD36 AND FSD37 COMBINATION FIRE and SMOKE DAMPERS
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FAX (816) 765-8955 INSTALLATION INSTRUCTIONS FSD35, FSD36 AND FSD37 COMBINATION FIRE and SMOKE DAMPERS 11/2 HOUR UL555 RATED UL555S LEAKAGE RATED
08-07-2015 MOUNTING INSTRUCTIONS
08-07-2015 i3hawm E(BASIC) MOUNTING INSTRUCTIONS 1. INDEX 1. Index 3 2. Important safety instructions 4 3. Maximum loads 7 4. Different configuraties 8 5. Part list i3hawm-e (basic) 9 6. Preparing frame
UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS
UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table
HDA -----------------------------------------------------------
----------------------------------------------------------- Lightstrips ---------------------------------------------------------------------- Ceiling system for heating and cooling LIGHTSTRIPS LIGHTSTRIPS
Description. Outlets Page 62. Contact foil Page 65. Accessories Page 65. Outlets Page 68. Accessories Page 69. Brackets Page 73.
Pluvia Syphonic roof rainage system Description Outlets Page 62 Pluvia outlets 12 l Contact foil Page 65 Accessories Page 65 Pluvia outlets 25 l Outlets Page 68 Accessories Page 69 Pluvia outlets 45/60/100
Now Available in Black Zinc Nickel
847/848 Series Power Supply up to 63 Now vailable in lack Zinc Nickel The 847/848 bayonet Series has been especially designed for light and harsh environment. Its physical characteristics and performances
KIRÁLY TRADING KFT H-1151 Budapest Mogyoród útja 12-14 tel: 061307-3801 Email_pzoli@kiralytrading.hu. Clamps Clamping devices
04000 Clamps Clamping devices 23000 22000 21000 20000 09000 08000 07000 06000 05000 04000 03000 02000 01000 297 04010 Adjustable straps Tempered steel 1.1191 Black oxide finish nlm 04010-101 Suitable thrust
SMD Rework Station TABLE OF CONTENTS
SMD Rework Station Thank you for purchasing the Hakko 50B SMD Rework Station. The Hakko 50B is designed to solder and desolder surface mounted devices with hot air. Please read this manual before operating
Batibox TM flush-mounting boxes for dry partitions
flush-mounting boxes for dry partitions 800 51 800 42 800 53 800 54 800 42 + 800 71 800 77 Cat.Nos 1-gang boxes For 1 module 20 800 40 Drilling diameter 32 mm Depth 40 mm For 1 gang or 2 modules For wiring
Mounting Instructions. Torque Transducer. A0329 3.2 en
Mounting Instructions Torque Transducer T5 T5 Contents 3 Page Safety instructions.............................................. 4 1 Measuring characteristics..................................... 7 2 Mounting.....................................................
K&T Saw Shop 606-678-9623 or 606-561-4983
11-600097F MINI-MAC 35AS 07/76 to 04/77 IPL 92754A-R1 Page 1 of 12 Accessories www.ktoutdoor.com 11-600097F MINI-MAC 35AS 07/76 to 04/77 IPL 92754A-R1 Page 2 of 12 Accessories 91753 Case - Carrying 88756
FL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT
-J070 REV. 0-0-0 FL ADJUSTABLE RIDER BACKREST MOUNTING HARDWARE KIT GENERAL Kit Number 9-09A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
Lift-off hinge. Rising hinge. Standard hinge. Heavy duty hinge. Parliament hinge. Spring hinge. Double action spring hinge. Concealed mortise hinge...
Door Hinges Contents Butt hinges Lift-off hinge Rising hinge Standard hinge Heavy duty hinge Parliament hinge Spring hinge Double action spring hinge Concealed hinges Concealed mortise hinge... Pivot
POWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
Installation guide for the SafeLine type anchorage device. Tested in compliance with EN 795: 1996. No.: SE-...
Installation guide for the SafeLine type anchorage device Tested in compliance with EN 795: 1996 No.: SE-... Version: 09.10.2008 SE 67 Subject to technical alterations! Contents 1. General information
Geberit Pluvia. Syphonic roof drainage system. Overview Page 42. Geberit Pluvia outlets 6 l. Geberit Pluvia outlets 14 l
Geberit Pluvia Syphonic roof rainage system Description Overview Page 42 Geberit Pluvia outlets 6 l Outlets Page 43 Contact foil Page 43 Outlets Page 44 Geberit Pluvia outlets 14 l eating element Page
Structural fire design Eurocode 5-1.2 Timber structures
Background and Applications Brussels, 18-20 February 2008 Dissemination of information workshop 1 Structural fire design Eurocode 5-1.2 Timber structures Jochen Fornather Austrian Standards Institute jochen.fornather@on-norm.at
Söll GlideLoc Aluminium Ladders. Vertical fall protection system Certified according to EN 353-1:2002 and CNB/P/11.073
Söll GlideLoc Aluminium Ladders Vertical fall protection system Certified according to EN 353-1:2002 and CNB/P/11.073 7 Söll GlideLoc Aluminium ladders Y-spar Profile 52 x 51 mm With connector Mounting
Check for deteriorated, shifting or missing tie-down pads. Replace if needed.
C C 0 5 C H A S S I S F R A M E Chassis Frame Overview The Blue Bird Vision s chassis frame consists of two main C-channel rails which run the entire length of the bus, and several different kinds of cross
2&3 SECTION LOFT LADDER
TWIST CATCH ASSEMBLY A4 A2 A1 A3 A7 A6 A5 2&3 SECTION LOFT LADDER Images feature the 3 section loft ladder, but the same instructions apply to both 2 & 3 section ladders Installation and Operating Instructions
Installation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES
PPS-PPQ-BT-PIAS RESIN INSULATORS FOR OIL INSULATED ELECTRICAL MACHINES BUSHING WITH PLUG CONNECTION WITH OUTER CONE PPS CHARACTERISTICS The PPS bushing can be used as a fixed section for the entry of medium
Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version
Installation instructions of the MIDI-Heki roof light with operating bar, with crank or electrical version with operating bar with crank electrical version 1. Prerequisite for a correct installation of
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS SOUCY TRACK SYSTEM 04-M113-1ENS (SPLIT IDLER) Litho d in Canada 1 04-M113-1ENS
M113 VEHICLE FAMILY RUBBER TRACK INSTALLATION INSTRUCTIONS (SPLIT IDLER) 1 # TABLE OF CONTENTS List of parts and tools................................................3 Installation of complete kit...................................................5
DEHN + SÖHNE. DEHNconductor System No Problems with Proximities
DEHN + SÖHNE DEHNconductor System No Problems with Proximities DEHNconductor System - New Possibilities for controling Proximities. For preventing dangerous flashovers among parts of external lightning
ASSEMBLY INSTRUCTIONS ACCORDING TO SAE J1453 FOR FLARED TUBES. 5. Clean properly with appropriate products the part of the tube to be flared.
ASSEMBLY INSTRUCTIONS ACCORDING TO SAE J1453 FOR FLARED TUBES 1. Before to start to flare the tube check for the correct parameters of all the tools to be used and substitute 2. Cut the tube at a 90 angle
Packaged Terminal Air Conditioner Wall Sleeve Installation
Installation & Maintenance Data IM 1196 Group: PTAC Part Number: 910141799 Date: October 2013 Packaged Terminal Air Conditioner Installation x 42" PGAN with Top-Mounted Hydronic Heat Note: Installation
INSTRUCTION MANUAL (WINDOW WIPER)
INSTRUCTION MANUAL (WINDOW WIPER) SUBJECT CONTENTS PAGE 1. GENERAL 2 2. CONTRUCTION 2 2-1. STRAIGHT LINE TYPE WINDOW WIPER 2 2-2. CONTROL BOX 2 2-3. SPARE PARTS 2 3. MECHANISM AND OPERATION 2 3-1. STRAIGHT
3. Geberit Pluvia Roof Drainage Systems
3. Geberit Pluvia Roof Drainage Systems Assortment overview: Pluvia Outlets...52 3.1 Roof outlets... 53 3.1.1 Roof outlets up to 25 l/s...53 3.1.2 Roof outlets up to 100 l/s...55 3.2 Roof outlets for gutters...
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR
TECHNICAL SPECIFICATION FOR HIGH TENSION LINE HARDWARE AND ACCESSORIES FOR ACSR PANTHER & WOLF CONDUCTOR 1.1.0 SCOPE : This specification covers design, manufacture, testing at manufacture s works before
Laserlyte-Flex Alignment System
Laserlyte-Flex Alignment System LaserLyte-Flex The LaserLyte-Flex Alignment System is a unique, interchangeable, low cost plug and play laser system. Designed specifically for aligning and positioning
Volkswagen B3 Passat General-Engine 4 CYL. 19 Engine - Cooling System (Page GR-19)
19 Engine - Cooling System (Page GR-19) Cooling system draining and filling general information Body components, layout Engine components, layout Radiator fan run-on checking Recommended mixture ratios
Trapezoidal-Connectors Series TMC
Trapezoidal-Connectors Series TMC Subminiature-D Connectors to DIN 41 652/IEC 807-3 General Series TMC connectors are available in 5 different housing sizes with 9, 15, 25, 37 and 50 pins. In applications
Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning
Manual piston sampler...m 11
SAMPLING Manual piston sampler...m 11 Screw sampler...prec 22...PREC 100 Slide sampler...pr 55 Rotative screw sampler...prv Piston sampler...p 11 Sampler on belt conveyor...pba Rotating cup sampler...pgr
GUIDELINES FOR INSTALLATION OF AIR CONDITIONING UNITS 174-180 PHILLIP STREET, SYDNEY
GUIDELINES FOR INSTALLATION OF AIR CONDITIONING UNITS 174-180 PHILLIP STREET, SYDNEY July 2008 1.0 SCOPE These guidelines describe the way in which air conditioning units shall be installed or replaced
Buy Karcher Parts Online: www.pressureparts.com. Need Technical Help? Call: 1-800-999-2245 email Requests to: sales@pressureparts.
Karcher Model:K 520M /CDN ( 59559150 ) - Parts Section:1.0 PIECE PARTS Page 1 of 16 1 50690940 1 COVER 2 50319770 1 COVER / 1.069-937.0 2 50312410 1 COVER 4 40503340 1 CHASSIS 5 51052230 1 AXLE 6 53215050
Saferand easierinstallation
EN 85-07 Saferand easierinstallation IföSigninstallationsystem andifösignbuilt-incistern www.ifosanitar.com/sign Aneffectivesolution withmanyadvantages. Ifö Sign installation system makes life a little
Feed-through terminal blocks for high-current applications
596 PHOENIX CONTACT With the feed-through terminal blocks, you can freely select the connection technology. Choose between traditional screw connection, robust bolt connection, and convenient push-in connection
AM/FM ANTENNA KIT (TOUR-PAK MOUNT)
-J077 REV. 008-0-0 AM/FM ANTENNA KIT (TOUR-PAK MOUNT) GENERAL Kit Number 7-98A Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SERIES 51
83 300/100 ED E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SUBPLATE MOUNTING CETOP P05 p max 250 bar Q max (see specification table) MOUNTING INTERFACE OPERATING PRINCIPLE
1. SAFETY RULES WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT".
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
Boiler Plan II Table of Contents
Cover Page Table Of Contents Introduction Parts List Additional Materials Assembly instructions Drawings 1-15 Boiler Plan II Table of Contents Introduction This will be a very rewarding project, if you
Knürr Smaract. Knürr Smaract. CompactRack
CompactRack Features Ample space for components and cabling provided in an efficient, compact design. The innovative frame concept with triangular extrusions ensures low weight while maintaining high stability.
Dear costumers, You have just received our new catalogue with KOPOS KOLIN a.s. offer of metal cable support system products. Those types of products
Dear costumers, You have just received our new catalogue with KOPOS KOLIN a.s. offer of metal cable support system products. Those types of products were firstly introduced on the market in year 2007.
CRN32-2-2 A-F-G-E-HQQE 3x400D 50 HZ
GRUNDFOS DATA BOOKLET CRN32-2-2 A-F-G-E-HQQE 3x4D 5 HZ Grundfos Pump 96122352 Thank you for your interest in our products Please contact us for more information, or visit our website http://www.lenntech.com/grundfos/crn32/96122352/crn-32-2-2-a-f-g-e-hqqe.html
4 Installation Requirements
4 Installation Requirements 9 4.1 Code Reference The authority having jurisdiction should be referenced to determine what law, ordinance or code shall apply in the use of flexible duct. Ducts conforming
INSTRUCTION MANUAL AND PARTS LIST MODEL 14-10
VERTICAL BAND SAWS INSTRUCTION MANUAL AND PARTS LIST MODEL 1-10 DAKE/PARMA WHEN ORDERING PARTS GIVE COMPLETE SERIAL NUMBER OF MACHINE GIVE PART NUMBER AND NAME GIVE AMOUNT REQUIRED Unless the above data
HORIZONTAL INSTALLATION
THERMO/SOLAR Žiar s.r.o. MANUAL FOR INSTALLATION PV SUPPORTING FRAMES HORIZONTAL INSTALLATION Technical alternation reserved A1410 1 12/2014 CONTENT ORD.NO. PAGE Mounting information 3 Mounting, flat roof
Power Window/Power Lock Installation. To begin with you will need all the parts listed below:
Power Window/Power Lock Installation To begin with you will need all the parts listed below: From Donor Fiero: Fiero power window regulators Power window motors (Generic GM type part) -motors are riveted