PURE WATER. Installation, Operation and Maintenance Manual Series PWBWGAC, PWBWMZ, PWBWCAL Filter Systems. Warning. Table of Contents.
|
|
- Meryl Bond
- 1 years ago
- Views:
Transcription
1 Installation, Operation and Maintenance Manual Series PWBWGAC, PWBWMZ, PWBWCAL Filter Systems PURE WATER IOM-WQ-PWBWGAC-PWBWMZ-PWBWCAL! Warning You are required to thoroughly read all installation instructions and product safety information before beginning the installation of this product. FAILURE TO COMPLY WITH PROPER INSTALLATION AND MAINTENTENANCE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH. Watts is not responsible for damages resulting from improper installation and/or maintenance. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Local building or plumbing codes may require modifications to the information provided. You are required to consult the local building and plumbing codes prior to installation. If this information is not consistent with local building or plumbing codes, the local codes should be followed. PWBWGAC PWBWMZ PWBWCAL Save manual for future reference. Refer to enclosed for operating parameters to ensure proper use with your water supply. Table of Contents Pages Important Safety Information Read All... 2 Instructions Before Using....2 Filter Anatomy...3 Specifications...4 Feedwater Parameters...4 Power...4 Installation Considerations...4 Drain Flow Rates...4 Setup...5 Installation...6 Controller....7 Filter Operation...7 Replenishing the Calcite Filter Media...7 Troubleshooting....7 Limited Warranty...8
2 Important Safety Information Read All! Caution: Read and follow the information in this manual to minimize the risk of electric shock or personal injury. Important: If you are unsure about installing your Watts water filter, contact a Watts representative or consult a professional plumber. Important: This system must be installed in compliance with applicable state province and local codes, law, and regulations. READ Instructions Before Using After reading these instructions completely, obtain all the materials and tools needed for installation. NOTE: Failure to install the system correctly voids the warranty. Perform installation according to state, province and local plumbing codes. Use only lead-free solder and flux for sweat-solder connections, as required by state, province and federal codes. Handle all components of the system with care. Do not drop, drag or turn components upside down. Be sure the floor under the water filter system is clean, level and strong enough to support the unit. The system uses 24 volt-60hz electrical power. Always use the transformer supplied. Plug transformer into an indoor 120 VAC, grounded outlet. Properly ground the system to conform with all codes and ordinances. Install the system in a protected area. Be sure electric outlet and transformer do not come in contact with water. For more information on where to install the filter see the Installation Considerations section of this manual. Do not attempt to treat water over 110 F (43 C) with the system. Always connect the system to the main water supply pipe before the water heater. Do not expose the system to freezing temperatures. Water freezing in the system causes equipment damage. Do not install in direct sunlight. Ultraviolet rays from the sun may cause damage. Minimum inlet water pressure is 30psi. Maximum inlet water pressure is 125psi. Use a pressure reducing valve if necessary.! Caution: Do not use with water that is microbiologically unsafe or of unknown quality. Test the water periodically to verify that the system is performing satisfactorily. Discard small parts remaining after the installation. 2
3 Filter Anatomy Item # Description 1 Valve 2 Bypass 3 Tank 4 Distributor 5 Filter Media (Calcite, Carbon, or Micro Z ) 6 Faceplate/Controls 7 Gravel Underbed 3
4 Specifications Feed Water Parameters! Do not use this system on water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system! Minimum inlet pressure: 30 psig Maximum operating pressure: 125 psig Minimum water temperature: 34 F (1 C) Maximum water temperature: 110 F (43 C) Power Voltage: 120VAC Frequency: 60Hz Power consumption: 7 Watts Maximum Installation Location: Indoors (Protect from direct sunlight) Minimum ambient temperature: 34 F (1 C) Maximum ambient temperature: 122 F (50 C) Drain Flow Rates - The drain system these filters are plumbed to must be able to accept the listed drain volumes for a period of 27 minutes. Micro Z Filters 9" X 48", 1 cubic ft. 7 gpm 10" X 54", 1.5 cubic ft. 7 gpm 12" X 52", 2 cubic ft. 10 gpm 13" X 65", 3 cubic ft. 15 gpm Carbon Filters: 9" X 48", 1 cubic ft. 4 gpm 10" X 54", 1.5 cubic ft. 5 gpm 12" X 52", 2 cubic ft. 7 gpm 13" X 65", 3 cubic ft. 9 gpm 16" X 65", 4 cubic ft. 15 gpm Calcite Filters: 9" X 48", 1 cubic ft. 7 gpm 10" X 54", 1.5 cubic ft. 7 gpm 12" X 52", 2 cubic ft. 10 gpm 13" X 65", 3 cubic ft. 15 gpm MODEL NO. Valve Mineral Tank Size Media Cubic Foot Gravel (Lbs) Service Flow* Pressure Drop (PSI) Back Wash Floor Space LXWXH PWBWMZ1 Time Clock 9" X 48" " X 10" X 55" PWBWMZ15 Time Clock 10" X 54" " X 11" X 62" PWBWMZ2 Time Clock 12" X 52" " X 13" X 60" PWBWMZ3 Time Clock 13" X 65" " X 14" X 74" model No. Valve Mineral Tank Size Media Cubic Foot Gravel (Lbs) Service Flow* Pressure Drop (PSI) Back Wash Floor Space LXWXH PWBWGAC1 Time Clock 9" X 48" < " X 10" X 55" PWBWGAC15 Time Clock 10" X 54" < " X 11" X 62" PWBWGAC2 Time Clock 12" X 52" < " X 13" X 60" PWBWGAC3 Time Clock 13" X 65" < " X 14" X 74" PWBWGAC4 Time Clock 16" X 65" < " X 17" X 74" MODEL NO. Valve Mineral Tank Size Media Cubic Foot Gravel (Lbs) PEAK Service Flow * Pressure Drop Back Wash Floor Space L X W X H PWBWCAL1 Time Clock 9" X 48" < " X 10" X 55" PWBWCAL15 Time Clock 10" X 54" < " X 11" X 62" PWBWCAL2 Time Clock 12" X 52" < " X 13" X 60" PWBWCAL3 Time Clock 13" X 65" < " X 14" X 74" *Note: Peak service flow rate is for intermittent use only and is not to be interpreted as continuous service flow rate capability. These systems are designed to treat the domestic water used in a single family dwelling. For irrigation water treatment or higher volume applications please contact your Watts representative. 4
5 Setup Unpack and check the system components for damage or missing parts. Make sure that the bypass valve and plumbing yoke are properly connected to each other and to the control valve with the mounting clips. Make certain that the drain line flow control fitting is installed properly on the drain port of the control valve. Systems that are 13 in diameter and larger are not loaded with media. These systems must be loaded with media before placing into service. To load a system follow the below steps. 1. Cap the top open end of the distributor tube with tape and plastic sheeting to keep foreign debris from entering the distributor tube. This cap must be secure and not come off during media loading. 2. Place the distributor tube, screen end down, into the mineral tank and center it in the bottom. The top of the distributor tube should be flush with the top of the tank. 3. Make sure the plastic and tape cap is secure to the top of the distributor tube, place a funnel on the top of the tank and load first the gravel then the filter media into the tank. The cap must not come off of the distributor tube during the loading of the media. 4. Remove the plastic cap from the distributor tube. DO NOT PULL UP ON THE DISTRIBUTOR TUBE when removing the cap. The distributor tube top must remain flush with the top of the tank. 5. Clean any media from the threads and top of the mineral tank. 6. Lubricate the O-rings on the bottom of the control valve (distributor pilot O-ring and top of tank O-ring). Use non-petroleum based silicone lubricant only. 7. Place the control valve on top of the tank. When doing this step, seat the top of the distributor tube inside the centered O-ring sealed port on the bottom of the valve first then press the valve down until the tank threads come in contact with the valve threads. This ensures that the distributor tube is properly seated into the bottom of the control valve. Thread the valve on to the tank clockwise. Be careful not to cross thread the valve or over tighten it. A hand tight snug fit is appropriate for the control valve torque. A wrench is not necessary. Do not use thread sealant or PTFE tape on the valve base threads. 8. The system is now ready for installation. Installation Considerations Consider the following points when determining where to install the filter: Place the system as close as possible to a sewer drain. Do not install the filter where it would block access to the water heater, or access to the main water shutoff, water meter, or electrical panels. Install the filter in a place where water damage is least likely to occur if a leak develops. A 120VAC electrical outlet is needed to plug in the transformer. Always connect the system to the main water supply pipe before the water heater. Install the system where it will not be subject to temperatures outside of the limits stated in the Specification section or to direct sunlight. Make sure the installation surface is smooth, level, and sturdy enough to support the weight of the wetted system. 5
6 Installation 1. Turn off gas or electric supply to the water heater. 2. Turn off the main water supply to pipes to be cut and drain the house water pipes. 3. Open both hot and cold faucets. 4. Move the filter assembly into installation position. Be sure the floor under the water filter system is clean, level and strong enough to support the unit. 5. Plumb IN and OUT connections to and from filter. Be sure the incoming water supply is connected to the INLET port of the valve. The valve body of the control is marked with arrows indicating the proper flow direction. Connections are illustrated below. 8. Fully open two (2) cold water faucets near the water filter. 9. Fully open the house main water shutoff valve. Observe a steady flow from both faucets. 10. Close the cold water faucets. 11. Check plumbing work for leaks and fix immediately if any are found. 12. Connect electrical power by plugging the transformer into a (120 VAC) outlet. Drain 13. Remove the cover from the valve. Press and hold the Extra Cycle button until the flashing BW symbol appears in the Parameter Display. 6. Connect and route the valve drain line using rigid piping or hose. Use the same size plumbing for the drain line as the fitting for the drain connection. The smallest units have a 1 2" connection, the larger sized units have a 3 4" connection. It is important to use the same size plumbing as the connection to ensure proper backwash flow. Properly secure the end of the drain line. Note: Leave an air gap of at least 1 1 2" between the end of the drain plumbing and the drain point. CAUTION: If making a soldered copper installation, do all sweat soldering before connecting pipes to the bypass valve. Torch heat will damage plastic parts. CAUTION: When turning threaded pipe fittings onto plastic fittings, use care not to cross-thread. CAUTION: Use PTFE tape on all external pipe threads. Do not use pipe joint compound. CAUTION: Support inlet and outlet plumbing in some manner (use pipe hangers) to keep the weight off of the valve fittings. 7. Place bypass valve in "bypass" position as shown below. 14. Unplug the valve when the BW symbol stops flashing and the countdown timer appears. This keeps the valve in an extended backwash for the initial startup. 15. Open the outlet bypass valve fully. 16. Open the inlet bypass valve slightly. Open the valve just until you hear water flowing. 17. Observe the drain flow. It may take several minutes for the filter vessel to fill up with water and begin to flow to drain. 18. After all the air is purged from the vessel and a steady drain flow is observed, allow the unit to backwash for 2 hours with the inlet valve open slightly. 19. Fully open the inlet bypass valve and allow the unit to backwash for 30 minutes. 20. After 30 minutes, observe the drain flow. If the drain flow is clear proceed to the next step. If the drain flow is still cloudy, allow it to continue to backwash until it is clear. 6
7 Installation continued 22. Plug the unit back in to the electrical outlet and allow it to finish the flush cycle. This will take approximately 20 minutes. 23. Set the time of day. Press and hold either the Up or Down buttons until the programming icon replaces the service icon and the parameter display reads TD. Adjust the displayed time with the Up and Down buttons. When the desired time is set, press the Extra Cycle button to resume normal operation. The unit will also return to normal operation after 5 seconds if no buttons are pressed. 24. Turn on the gas or electric supply to the water heater after all air has been purged from the house's plumbing system and water heaters. Controller The factory default program settings should be adequate for most installations. See the ProFlo SXT Service Manual included with the unit for advanced programming options. Filter Operation As water enters the filter, it passes through the filter media. Over time, suspended solids accumulate in the filter media and need to be rinsed out. This is accomplished by performing a backwash. During backwash the filter is in automatic bypass allowing unfiltered water to pass downstream. The automatic backwash is initiated based on time and is normally set to occur in the middle of the night. This System Has Three Positions: 1. Backwash Position Backwash is a rapid upward flow of water that loosens the filter bed and flushes dirt and sediment captured in the bed out to the drain. 2. Fast Rinse Position Fast Rinse is a fast flow of water down through the filter bed that follows a Backwash. This packs the filter bed for the next service cycle. 3. Service Position When the filter is In Service, water is flowing through the system and sediment is being removed from your water if it s a Micro Z filter. If it s a carbon filter, it removes chlorine, tastes, odors, and organics from your water. If your system contains calcite media your water's acidic ph will be raised closer to a value of 7. Replenishing Calcite Filter Bed Media As low ph water is neutralized by the calcite filter media a small amount of calcite dissolves into the water. Over a period of time calcite media will need to be added to the system so that it can continue to perform properly. The need to add calcite media to the system can be verified by performing a ph test on the treated water. If the results of the ph test show a value below 6.5 ph units contact your system installer or local water treatment professional to have the media bed replenished. Troubleshooting Problem Cause Solution 1. Loss of Water Pressure Sediment buildup in filter bed A. Perform a manual backwash B. Make sure unit is plugged in C. Replace media 2. Drain Flows Continuously Foreign material in control Remove piston assembly and inspect bore, remove foreign material & check control in various ports 3. Wrong time of day Power Outage Reset time of day. Be sure power supply in uninterrupted 4. Controller Cycles Continuously Faulty timer board or microswitch Replace defective components 5. Unfiltered water in house A. Bypass in Bypass position A. Move Bypass to service position B. Valve stalled in backwash B. Have valve serviced C. Media needs to be replaced C. Have system serviced Note: Error codes appear in the service display. Error code Cause Solution (Err 0) Drive motor is stalled See above troubleshooting table, #5-B (Err 1) Drive water runs continuously See above troubleshooting table, #4 (Err 2) There has been more than 99 days since the last regeneration Initiate a manual regeneration (Err 3) Control Board memory failure Replace control board 7
8 LIMITED WARRANTY: Certain Watts Pure Water products come with a limited warranty from Watts Regulator Co. Other products may have no warranty or are covered by the original manufacturer s warranty only. For specific product warranty information, please visit or the published literature that comes with your product. Any remedies stated in such warranties are exclusive and are the only remedies for breach of warranty. EXCEPT FOR THE APPLICABLE PRODUCT WARRANTY, IF ANY, WATTS MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, WATTS HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND IN NO EVENT SHALL WATTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR PROPERTY DAMAGE, REGARDLESS OF WHETHER IT WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES. A Watts Water Technologies Company USA: Tel. (800) Canada: Tel. (888) IOM-WQ-PWBWGAC-PWBWMZ-PWBWCAL 1225 EDP# Watts
WATER SOFTENER SYSTEMS
INSTALLATION MANUAL WATER SOFTENER SYSTEMS HousePure Models HP-Soft-2 HP-Soft-4 736-0137 Water, Inc. 1044 East Del Amo Blvd., Carson, CA 90746 www.waterinc.com 310-885-4400 P/N 41482 Rev A 06/04 Table
TABLE OF CONTENTS. General Warnings Installation Programming System Start-Up Frequently Asked Questions...
Service Manual Table of Contents TABLE OF CONTENTS Page General Warnings... 3 Installation... 5 Programming... 7 System Start-Up... 8 Frequently Asked Questions... 10 Drawings and Part Numbers... 11 Front
Filter Owners Manual Models
Filter Owners Manual Models PF 0840cb PF 0840n PF 0840m PF 1040cb PF 1040n PF 1040m PF 1240cb PF 1240n PF 1240m PF 1354e Rev. 04/2010 Page 2 Product No. 13130A Table of Contents Product Line Overview Page
MASTER. Water Conditioning Corp. MBA-10/13 FILTERS with the 253/742 Logix Control Valve. Installation and Operation Manual. www.masterwater.
MASTER Water Conditioning Corp. www.masterwater.com Installation and Operation Manual MBA-10/13 FILTERS with the 253/742 Logix Control Valve June 2010 Table of Contents Page No. Topic Description 1 Model
Water Softening Systems Operation & Maintenance Manual
Water Softening Systems Operation & Maintenance Manual Specifications Feedwater! Do not use this system on water that is microbiologically unsafe or of unknown quality without adequate disinfection before
MBA-MM-1040/10/13/1665 MULTI MEDIA FILTERS
MASTER Water Conditioning Corp. www.masterwater.com Installation and Operation Manual MBA-MM-1040/10/13/1665 MULTI MEDIA FILTERS with the 263/742 Logix Control Valve June 2010 Table of Contents Page No.
Softener Owners Manual
Softener Owners Manual Models PS 0840 Timer PS 1040 Timer PS 1054 Timer PS 0840 Metered PS 1040 Metered PS 1054 Metered PS 0840x Timer PS 1040x Timer PS 1054x Timer PS 1353x Timer PS 0840x Metered PS 1040x
MASTER. Installation and Operation Manual. Water Conditioning Corp. MCA Time Clock Series Residential Softeners. February 2011 Version
MASTER Water Conditioning Corp. Installation and Operation Manual MCA Time Clock Series Residential Softeners February 2011 Version Table of Contents Page No. Topic Description 1 Model # and Packaging
Water Tec of Tucson Water Systems
Water Tec of Tucson Water Systems Water Filter Owner s Manual Water Tec of Tucson www.water-tec.com 4601 S. 3 RD Avenue Tucson, AZ 85714 (520) 790-1512 Fax (520) 745-0549 1 MAIN COMPONENTS Your water treatment
MASTER. Water Conditioning Corp. MP-MBA-15T-30T using the 255/762 Logix Control Valve. Installation and Operation Manual. www.masterwater.
MASTER Water Conditioning Corp. www.masterwater.com Installation and Operation Manual MP-MBA-15T-30T using the 255/762 Logix Control Valve July 2006 Table of Contents Page No. Topic Description 1 Model
Model 7000 Service Manual
Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specifications Sheet..................................................................... 3
Installation, Operation and Maintenance Manual
Installation, Operation and Maintenance Manual Fusion Upflow Calcite Filter ph Neutralizer Filter 111-UFF-Cal-1 111-UFF-Cal-2 111-UFF-Cal-3 111-UFF-Cal-4 US Water Systems, Inc. 1209 Country Club Road Indianapolis,
MASTER. Installation and Operation Manual. Water Conditioning Corp. MP-MCA Residential Metered Softeners. January 2012 Version
MASTER Water Conditioning Corp. Installation and Operation Manual MP-MCA Residential Metered Softeners January 2012 Version Table of Contents Page No. Topic Description 1 Performance Data Sheet MP-MCA-30T
3M Water Filtration Products. CFS01 Series, CFS02 Series, CFS11 Series, and CFS12 Series Housings. Installation and Instruction Manual For:
3M Water Filtration Products Installation and Instruction Manual For: CFS01 Series, CFS02 Series, CFS11 Series, and CFS12 Series Housings Installer: Please leave this manual with owner/operator. Owner/Operator:
Series 9000 Water Treatment System
Series 9000 Water Treatment System Owners Manual Installation Service & Parts Operation Guide The Clear Choice for Soft, Conditioned Water TABLE OF CONTENTS Page Pre-Installation Review --------------------------------------------------------------------------------
Pro-OX 7800 Iron Filter Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com Pro-OX 7800 Iron Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
PURE WATER. Installation, Operation and Maintenance Manual. Ultra Filtration Membrane Water Filtration System Model PWDWUFKC3.
Installation, Operation and Maintenance Manual Ultra Filtration Membrane Water Filtration System Model PWDWUFKC3 IOM-WQ-PWDWUFKC3 PURE WATER Important Please read the entire manual before proceeding with
10/20 COMBINATION UNIT
MASTER Water Conditioning Corp. www.masterwater.com Installation and Operation Manual 10/20 COMBINATION UNIT with the 255/742 Logix Control Valve With Vortech October 2006 Table of Contents Page No. Topic
Part No.: Rev: C 10/08
RainSoft Division of Aquion Water Treatment Products 2080 East Lunt Avenue Elk Grove Village, Illinois 60007 1.847.437.9400 or 1.800.860.7638 www.rainsoft.com QRS SERIES WATER TREATMENT SYSTEM The QRS
Fleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET
Fleck 4650 Service Manual TABLE OF CONTENTS JOB SPECIFICATION SHEET...1 INSTALLATION AND START-UP PROCEDURE...1 CONTROL VALVE DRIVE ASSEMBLY...2 CONTROL DRIVE ASSEMBLY FOR CLOCK...3 BYPASS VALVE ASSEMBLY...4
Fleck 7000 Carbon Filter Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 7000 Carbon Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
Model 6600 Downflow. Service Manual. IMPORTANT: Fill in pertinent information on page 3 for future reference.
Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specification Sheet...................................................................................
7500 Pro-Ox Filter Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com 7500 Pro-Ox Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your
Owner s Manual. Safety Instructions Installation Maintenance Warranty. Models: 2-5 Gallon Capacity
WATER HEATER THERMAL EXPANSION TANKS Owner s Manual Safety Instructions Installation Maintenance Warranty Models: 2-5 Gallon Capacity Thank You for purchasing this Thermal Expansion Tank. Properly installed
Model 5600SE Downflow
Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specification Sheet...................................................................................
GE LOGIX WATER SOFTENER INSTALLATION
GE LOGIX WATER SOFTENER INSTALLATION Discount Water Softeners recommends using a licensed plumber to install your water softener. The following installation instructions are for use with the water softener
SUPERPLUS WATER FILTRATION SYSTEM
SUPERPLUS WATER FILTRATION SYSTEM For Model #: SP20-2, SP40-2 INSTRUCTIONS/ASSEMBLY USE AND CARE MANUAL (Important: Read this manual thoroughly before install) TABLE OF CONTENTS 2 3 4 6 8 9 10 11 12 General
WS1 Neutralizer Installation & Start Up Guide
WS1 Neutralizer Installation & Start Up Guide For Neutralizers with Vortech Distributor Screen Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your
Owner s Manual. Calcite ph Neutralizer
Owner s Manual Page 2 Copyright 2012 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes no warranty
DUROsoft EM. Electronic Meter Initiated Softeners OPERATION MANUAL
DUROsoft EM Electronic Meter Initiated Softeners OPERATION MANUAL PLEASE NOTE: On page seven of this manual you will find important maintenance procedures for the continued proper operation of your unit.
Upflow Neutralizer Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com Upflow Neutralizer Installation & Start-Up Guide For Up-Flow Neutralizers with Vortech Distributor Screen Thank you for purchasing a Clean Water System! With
Fleck 5600 Softener Installation & Start Up Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 5600 Softener Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
Watts Pure Water Systems
Watts Pure Water Systems WM-120-PT Installation and Operation Manual Premier Water Systems Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before
Safety Guides Installation Operation
OWNERS MANUAL MODEL WHFS DELUXE WHOLE HOUSE FILTER HOUSG Safety Guides Installation Operation Cartridge Replacement Repair Parts If you have questions when installing, operating or maintaining your deluxe
Clean Water Made Easy
Clean Water Made Easy http://www.cleanwaterstore.com Pro-OX 5700-E Iron Filter Installation & Start- Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine
Iron Air Charge 2510-SXT Installation & Start-Up Guide
Iron Air Charge 2510-SXT Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your system will be providing iron free water
Calcite PH Nutralizer System
Calcite PH Nutralizer System Installation, Operation & Maintenance Manual Facts About Calcite Ph Neutralizers Calcite is a crushed and screened white marble media which can inexpensively be used to neutralize
Metermatic SE Automatic Water Softener. Operation Manual
Metermatic SE Automatic Water Softener Operation Manual Page 7 of this manual contains important maintenance procedures for the continued proper operation of your unit. These MUST be performed regularly
INSTANT HOT WATER RECIRCULATING SYSTEM
INSTANT HOT WATER RECIRCULATING SYSTEM INSTALLATION AND OPERATING INSTRUCTIONS Save manual for future reference Pump and Comfort Valve CS VW MH26400 65GM U P C 12" Supply Line and Adapters ANSI/NSF STD.
THERMOSTATIC MIXING VALVE TRIM K-T9493, K-T9494
THERMOSTATIC MIXING VALVE TRIM K-T9493, K-T9494 1. BEFORE YOU BEGIN IMPORTANT INSTRUCTIONS READ AND SAVE FOR THE CONSUMER WARNING: Risk of scalding or other severe injury. Before completing installation,
Clean Water Made Easy
Clean Water Made Easy www.cleanwaterstore.com 5700-E Neutralizer Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your
Model 5600 & 5600 Econominder
Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specification Sheet...................................................................................
Model 5600 & 5600 Econominder
Model 5600 & 5600 Econominder Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specification Sheet.........................................................................
Indirect-Fired Storage Water Heater Models WH-30 through WH-80 INSTALLATION AND OPERATING INSTRUCTIONS
Indirect-Fired Storage Water Heater Models WH-30 through WH-80 INSTALLATION AND OPERATING INSTRUCTIONS Contents Page Ratings and Specifications..................... 2 Installation Requirements......................
USE &CARE GUIDE. Remote Faucet Pump System. See Important Safeguards on page 2
Remote Faucet Pump System USE &CARE GUIDE See Important Safeguards on page 2 An exclamation point within an equilateral triangle is intended to alert user to the presence of important operating and maintenance
Electronic Instant Hot Water Appliance Installation, Operation and Care Instructions
Electronic Instant Hot Water Appliance Installation, Operation and Care Instructions Please read these instructions fully before commencing the installation and operation of the Electronic Instant Hot
Fleck 7000 Softener Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 7000 Softener Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
OWNERS MANUAL ECOJET
OWNERS MANUAL ECOJET ECO-JET Self-priming pumps ideal for supplying water for domestic and irrigation applications. 1) 1 Suction 2) 1 Discharge 3) Fill Plug 4) Drain Plug Fig. A 115V/60Hz Dear Customer,
Comfort Series Instant Hot Water System
GRUNDFOS INSTRUCTIONS Installation and Operation Comfort Series Instant Hot Water System ANSI/NSF61 and AIPMO approved Shipment Inspection page 1. Pre-Installation Checklist page 1. Pump Mounting page
Metermatic Water Softener. Operation Manual
Metermatic Water Softener Operation Manual Page 6 of this manual contains important maintenance procedures for the continued proper operation of your unit. These MUST be performed regularly for your guarantee
WS1 Greensand Installation & Start Up Guide
WS1 Greensand Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your system will be providing filtered water for many
Water Tec of Tucson Water Systems
Water Tec of Tucson Water Systems Water Softener Owner s Manual Water Tec of Tucson www.water-tec.com 4601 S. 3 RD Avenue Tucson, AZ 85714 (520) 790-1512 Fax (520) 745-0549 MAIN COMPONENTS Your water treatment
Fleck 7000 Neutralizer Installation & Startup Guide
Clean Water Made Easy www.cleanwaterstore.com Fleck 7000 Neutralizer Installation & Startup Guide For Neutralizers with Vortech Distributor Screen Thank you for purchasing a Clean Water System! With proper
INSTANT HOT WATER RECIRCULATING SYSTEM
INSTANT HOT WATER RECIRCULATING SYSTEM INSTALLATION AND OPERATING INSTRUCTIONS Save manual for future reference MODEL 500800 Warning Please read carefully before proceeding with installation. Your failure
GE SmartWater Water Filtration System Icemaker Connection Kit (RVKIT)
GE SmartWater Water Filtration System Icemaker Connection Kit (RVKIT) INSTALLATION INSTRUCTIONS For use with models GXRV10, GXRM10, PNRQ15, PNRQ20, PNRV12 (beginning on page 1) and PNRV18 (beginning on
INSTALLATION & START-UP INSTRUCTIONS FLECK 5600 METER WATER SOFTENER SYSTEMS. 1999-2007 QualityWaterForLess.com - 1 -
INSTALLATION & START-UP INSTRUCTIONS FLECK 5600 METER WATER SOFTENER SYSTEMS 1999-2007 QualityWaterForLess.com - 1 - info@qualitywaterforless.com Preface: Thank you for your purchase of a new Water Softener
Installation and Operation Manual
Model WHED20 How to install, operate and maintain your Undersink Drinking Water Filter System Do not return unit to store If you have any questions or concerns when installing, operating or maintaining
Owner s Manual. 5600 / 5600 Econominder
5600 / 5600 Econominder Owner s Manual For questions or in case of emergency, please call your local service technician (preferably the one who installed the system). Product Features, Benefits, & Job
GE SmartWater INSTALLATION INSTRUCTIONS. Heavy Duty Water Filtration System GNWH38F SAFETY PRECAUTIONS PROPER INSTALLATION
GE SmartWater INSTALLATION INSTRUCTIONS Heavy Duty Water Filtration System GNWH8F Check with your state and local public works department for plumbing and sanitation codes. You must follow these guidelines
This product was manufactured in an ISO 9001:2000 certified facility.
This product was manufactured in an ISO 9001:2000 certified facility. RainSoft Division of Aquion Water Treatment Products, LLC 2080 East Lunt Avenue Elk Grove Village, Illinois 60007 Main Switchboard:
Ceiling Mount Air Handler Manual
www.surna.com 303.993.5271 Ceiling Mount Air Handler Manual Models: CMAH12, CMAH18, CMAH24, CMAH30, CMAH36, CMAH48, CMAH60 Revised: September 2014 Table of Contents Warranty Information 4 Limited Warranty
Installation and Troubleshooting Instructions for Electric Tankless Residential Water Heaters.
Model Number: Serial Number: Information Manual Installation and Troubleshooting Instructions for Electric Tankless Residential Water Heaters. ATTENTION: IF YOU ARE NOT A LICENSED PLUMBER OR A LICENSED
CARING FOR YOUR WATER HEATER
http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html Water Heater Inspections CARING FOR YOUR WATER HEATER Venting System (Direct Vent Only) The venting system should be inspected
Installation and Operating Instructions Installation Instructions for SS EPE-316L Series
INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This
GUARDIAN CP DIGITAL PUMP CONTROL
GUARDIAN CP DIGITAL PUMP CONTROL INSTALLATION & OPERATION INSTRUCTIONS Your Guardian CP DIGITAL CONTROL has been carefully assembled and factory tested. To enjoy the full service this unit can provide,
USER MANUAL. Bottom Loading Bottled Water Dispenser SAVE THIS MANUAL FOR FUTURE USE. Model # 900142
Model # 900142: Page 1 Bottom Loading Bottled Water Dispenser Model # 900142 USER MANUAL TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING
What you can expect from your Solar Hot Water System
Owner s Manual Your Solar Hot Water System Thank you for your investment in the FAFCO Solar Hot Water System. Since 1969 our goal has been to design, test, and produce solar heating systems that save you
36G22, 36G23, 36G24 & 36G52 36J22, 36J23, 36J24 & 36J52 DSI and HSI Single Stage Combination Gas Valve
Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Digital Pressure Control Model WWDPC Your WWDPC has been carefully assembled and factory tested. To enjoy the full service this unit can provide, you
MODEL 5600 & 5600 ECONOMINDER
Service Manual IMPORTANT: Fill in pertinent information on page 2 for future reference. Job Specification Sheet JOB NO. *MODEL NO. WATER TEST CAPACITY PER UNIT MAX. PER REGENERATION MINERAL TANK SIZE DIA.
AMX300 DirectConnect Mixing Valve Kits
AMX300 DirectConnect Mixing Valve Kits INSTALLATION INSTRUCTIONS Tools needed (not supplied) 1. Wrench 2. Pliers Safety Definitions These safety terms identify information you must read. CAUTION Indicates
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
MODEL 9000. Service Manual. IMPORTANT: Fill in pertinent information on page 2 for future reference.
MODEL 9000 Service Manual IMPORTANT: Fill in pertinent information on page for future reference. Job Specification Sheet * JOB NO. * MODEL NO. * WATER TEST * CAPACITY PER UNIT MAX. PER REGENERATION * MINERAL
Water Softening. system. GE Appliances. Safety Instructions Proper installation...3. Owner s Manual & Installation Instructions
GE Appliances Water Softening system Safety Instructions Proper installation............3 Installation Instructions Drain connections..........7, 8 Important recommedations....4 Installation instructions......4-6
Dehumidifier Users manual. For Models: DH45S DH65S
Dehumidifier Users manual For Models: DH45S DH65S 950-0062-revD Jan. 9 2007 FORWARD The appearance of the units that you purchase might be slightly different from the ones described in the Manual, but
Owners Manual. 565 Valve Filter
565 Valve Filter Owners Manual FOLLOWTHE INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO INSTALL THE UNIT PROPERLY VOIDS THE WARRANTY. BEFORE YOU BEGIN INSTALLATION, READ THIS ENTIRE MANUAL. THEN, OBTAIN
USER MANUAL. Bottom Loading Bottled Water Dispenser SAVE THIS MANUAL FOR FUTURE USE. Model # 900172
Model # 900172: Page 1 USER MANUAL Bottom Loading Bottled Water Dispenser Model # 900172 TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING
Installation Instructions 4662.003
Installation Instructions.00 SINGLE CONTROL KITCHEN FAUCET Thank you for selecting American-Standard...the benchmark of fine quality for over 00 years. To ensure that your installation proceeds smoothly--please
Owner s Manual. Pelican Custom Premium WHWF 1865/2162
Owner s Manual Pelican Custom Premium WHWF 1865/2162 Page 2 Copyright 2013 Enviro Water Solutions Inc. All rights reserved. All information contained herein is the property of Pelican Water Systems. Pelican
Water Tec of Tucson. WS1TA Twin Alterna ng Water so ener
Water Tec of Tucson WS1TA Twin Alterna ng Water so ener Water Tec of Tucson www.water-tec.com 4601 S. 3 RD Avenue Tucson, AZ 85714 (520) 790-1512 Fax (520) 745-0549 MAIN COMPONENTS Your water treatment
OWNER S MANUAL. Certified to NSF/ANSI 61. This product is covered by one or more of the following US patent US D692, 524 S
OWNER S MANUAL Certified to NSF/ANSI 61 This product is covered by one or more of the following US patent US D692, 524 S CONTENTS INTRODUCTION CUSTOMER SUPPORT IMPORTANT NOTES SPECIFICATIONS INSTALLATION
Installation, Maintenance, & Repair Series 4000B/LF4000B
Installation, Maintenance, & Repair Series 4000B/LF4000B Reduced Pressure Zone Assemblies Sizes: 1 2" 2" (15 50mm) RP/IS-A-4000B 4000B/LF4000B Size: 3 /4"! WARNING Testing Read this Manual BEFORE using
Air Release Valve Series 38, 45, 50 (Compound Lever Type)
Manual No. ARCL-OM1-1 Air Release Valve Series 38, 45, 50 (Compound Lever Type) Operation, Maintenance and Installation Manual INTRODUCTION... 1 RECEIVING AND STORAGE... 1 DESCRIPTION OF OPERATION... 1
Do not extend the hot water outlet tube. Minimum working pressure: 220kPa (system might not work properly if the pressure is below the requirement).
XSENTIAL X-301 INSTANT HOT WATER DISPENSER INSTALLATION & OPERATING GUIDE 1.0 Components: When you purchase the Diana Instant Hot Water tank, contents include: 1. X-301 boiler 2. DLX-580 faucet 3. Feed
Whole House Water Treatment System. Installation, Operation and Maintenance Manual. Multi-Pure Model TO15000
Multi-Pure Whole House Water Treatment System Installation, Operation and Maintenance Manual Multi-Pure Model TO15000 Warning Please read manual carefully before proceeding with installation. It is recommended
USER MANUAL. Bottom Loading Bottled Water Dispenser SAVE FOR FUTURE USE. Model # 900157
Model # 900157: Page 1 USER MANUAL Bottom Loading Bottled Water Dispenser Model # 900157 TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE, USER MUST READ THIS MANUAL BEFORE ASSEMBLING, INSTALLING & OPERATING
Model 9000/9100/9500 Service Manual
Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference. Table of Contents Job Specifications Sheet..................................................................... 3
Installation Manual NEXUS - TB794DD Deck-Mounted Faucet
Installation Manual NEXUS - TB794DD Deck-Mounted Faucet Warranty Registration and Inquiry For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit our web
Installation and Op er a tion Man u al. Jandy NeverLube Backwash Valve Protected under U.S. Patents 6,240,941 and 6,568,428; other patents pending.
Installation and Operation Data Installation and Op er a tion Man u al Jandy NeverLube Backwash Valve Protected under U.S. Patents 6,240,941 and 6,568,428; other patents pending. FOR YOUR SAFETY - This
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS 1. WARNING To guard against injury, basic safety precautions should be observed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 2. DANGER To avoid possible
Freedom8 ShoeBox Compressor Manual
Freedom8 ShoeBox Compressor Manual Warning!! This product is not a toy! Use or misuse can cause severe injury or death! Use only with adult supervision. This unit is only to be used with tanks, hoses and
Electric Mini Tank Water Heaters
Electric Mini Tank Water Heaters EMT1 - EMT2.5 - EMT4 - EMT6 Installation and Operating Instruction Manual Table of Contents Important Safety Instructions 2 Technical Data 3-4 General Information 5 Technical
Model 800 Residential Steam Humidifier Owner s Manual. Includes Safety & Operating Instructions and Warranty Information
Steam Humidifier Model 800 Residential Steam Humidifier Owner s Manual Includes Safety & Operating Instructions and Warranty Information READ AND SAVE THESE INSTRUCTIONS TABLE OF CONTENTS Safety Cautions...
RXD Water Softener. Water Conditioning. Owner s Manual R4039. RXD Owner s Manual. Page 1
R Water Conditioning Owner s Manual R4039 RXD Water Softener This manual contains information on setting the controller and normal operating maintenance required by the owner. Page 1 UNPACKING INFORMATION
20 Solar Heating System Item #s 6860, 6947 & 6945
20 Solar Heating System Item #s 6860, 6947 & 6945 INSTALLATION & OPERATION MANUAL Please read all instructions carefully before installing your system. Your warranty and your enjoyment of the Solar Heating
SunMaxx Solar Filling Station Operating Instructions
SunMaxx Solar Filling Operating Instructions Content 1. Declaration of conformity... 2 2. Introduction... 2 3. Transportation and unpacking... 4 4. Mounting and commissioning... 5 5. End of operation...
WARNING. Before using this product, read and understand instructions.
Series WFE Uni-Match Electric Water Feeder Applications: For use on boilers with mechanical (float type) or electronic (probe type) LWCO's. McDonnell & Miller Installation & Maintenance Instructions MM-323
TECHNICAL INSTRUCTIONS REPAIR KITS Hydroguard Series 420 Thermostatic Valve All Models (1 9)
Form TI420-KIT A Watts Industries Co. TECHNICAL INSTRUCTIONS REPAIR KITS Hydroguard Series 420 Thermostatic Valve All Models (1 9) DESCRIPTION Thank you for purchasing a Powers kit. The Powers kit you
Sand Filter - Owner s Manual
Sand Filter - Owner s Manual INSTALLATION, OPERATION & PARTS! WARNING This equipment must be installed and serviced by a qualified technician in accordance with all applicable codes and ordinances. Improper
1 HP Swimming pool PUMP
1 HP Swimming pool PUMP 67333 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.