Alarm Clock Radio Thanks for buying a TEAC. Read this manual carefully to get the best performance from this unit.

Transcription

1 Alarm Clock Radio Thanks for buying a TEAC. Read this manual carefully to get the best performance from this unit.

2 IMPORTANT SAFETY Safety Considerations The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. To be completely disconnected the power input, the mains plug of apparatus shall be disconnected from the mains. The mains plug of apparatus should not be obstructed OR should be easily accessed during intended use. The marking information is located at the bottom of apparatus. Battery shall not be exposed to excessive heat such as sunshine, fire or the like. Minimum distances around the apparatus for sufficient ventilation. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc; No naked flame sources such as lighted candles should be placed on the apparatus. Attention should be drawn to environmental aspects of battery disposal; The use of apparatus in moderate climate. Electrical Information Make sure that the voltage of your electricity supply is the same as that indicated on the rating plate of the power supply unit supplied with your product. It requires a compatible mains supply. Do not use any other supply. 1

3 LOCATION OF CONTROLS AND INDICATORS 1. FM ANTENNA 10. SNOOZE BUTTON 2. AC POWER CORD 11. CLOCK SET BUTTON 3. DIMMER SWITCH 12. FUNCTION SELECTOR 4. POWER SELECTOR 13. SLEEP BUTTON 5. ALARM SET BUTTON 14. TUNING KNOB 6. VOLUME CONTROL 15. MINUTE BUTTON 7. AUX IN JACK 16. CLOCK PM TIME INDICATOR 8. HOUR BUTTON 17. ALARM INDICATOR 9. CLOCK DISPLAY 2

4 POWER SOURCE This unit is designed to operate on normal household AC power rated at 240V/50Hz. Operating this unit from any other power source may cause damage to the unit, and such damage is not covered by your warranty. It is also equipped with a battery back-up system for the clock that is powered by an optional 9V 006P battery (type 6F22 or equivalent not included). BATTERY BACK UP SYSTEM The Battery Back-up System ensures the clock and alarm settings will be retained during a power interruption or power outage (in order to preserve the battery life the Display will not light). All clock settings will be kept in memory, however, the clock time may require adjustment for exact accuracy once the power returns. If a battery is not installed, the Display will blink 12:00 when the power is restored. This will indicate that you have to reset the time and alarm settings. BATTERY INSTALLATION 1. Open the battery compartment door on the bottom of the cabinet and connect a 9V DC battery to the Battery Clip located inside. Note: The battery clip only fits one way to ensure the correct polarity. 2. Replace the Battery Compartment Door. Important: Be sure that the battery is installed correctly. Wrong polarity may damage the unit. 3. For optimum performance, an alkaline-type battery is recommended. If the unit is not to be used for an extended period of time, remove the battery. An old or leaking battery can cause damage to the unit and will void the warranty. 4. Do not try to recharge batteries that are not intended to be recharged; they can overheat, rupture and leak. (Follow the battery manufacturer s directions). 5. Do not dispose of batteries in fire, batteries may leak or explode. DIMMER CONTROL Slide the DIMMER switch on rear panel to High/Low position to control the display brightness. POWER FAILURE INDICATOR If there is no battery installed in the unit or the battery installed is weak or dead, the time and alarm settings will be lost if the power is interrupted. When the AC power is restored the display will flash 12:00. This indicates that the time displayed is incorrect and needed to be reset. 3

5 CLOCK SETTINGS When you plug the radio to an AC outlet for the first time the clock display will begin flashing "12:00". The flashing will stop when you set the time. 1. Slide the POWER selector to OFF position. 2. Press and hold the CLOCK SET button and repeatedly press the HOUR button and MINUTE button to set the correct time. NOTE 1. There is a PM indicator located in the top right-hand corner of the clock display. Be sure to observe the PM indicator when setting the time to make sure the time is set correctly for AM or PM. If the PM indicator is 'On', the time displayed is "PM". If the PM indicator is 'Off, the time displayed is "AM ". 2. After you reset the time, be sure to reset your alarm settings as well. RADIO OPERATIONS 1. Slide the POWER selector to ON position. 2. Slide the FUNCTION selector to the desired radio band, AM or FM. 3. Rotate the TUNING knob to select your desired station. 4. Adjust the VOLUME knob to the desired listening level. 5. Slide the POWER selector to OFF position to turn the radio off. TIPS FOR BEST RADIO RECEPTION AM - The AM antenna is built inside the radio. If AM reception is weak, slightly rotate or change the position of the unit until the internal antenna picks up the strongest signal. FM - If FM reception is weak, fully extend the wire antenna and vary the position and location of the antenna until you find the strongest signal. AUXILIARY INPUT OPERATIONS This unit provides an auxiliary audio signal input for connecting your external audio devices such as a MP3 player. 1. Slide the POWER selector to ON position. 2. Slide the FUNCTION selector to AUX position. 3. Turn on your external audio device. 4. To connect the unit and your external device by using your 3.5 mm plug audio cable (not included). 5. Adjust the VOLUME knob and/or your external audio device to the desired listening level. 6. Slide the POWER selector to OFF position and plug out your audio cable to stop listening your external audio device. 4

6 ALARM OPERATIONS 1. Slide the POWER selector to OFF position. 2. Press and hold the ALARM SET button and repeatedly press the HOUR and MINUTE button to set your desired wake up time. 3. When the wake up time is reached, the alarm will be functioning and will play for your desired wake up source about one hour and then shut off automatically. 4. If press the ALARM SET button to stop the alarm function, the alarm remains set and will turn the unit on again at the same time on the following day. 5. If slide the POWER selector to OFF position to stop the alarm function, the ALARM indicator will turn off. The alarm remains set but the alarm will not be functioning on the following day. NOTE: 1. There is a PM indicator located in the top right-hand corner of the clock display. Be sure to observe the PM indicator when setting the alarm to make sure the alarm time is set correctly for AM or PM. If the PM indicator is 'On', the alarm time will be "PM". If PM indicator is 'Off, then the alarm time will be "AM ". 2. Press and hold the ALARM SET button to check the wake up time. SETTING FOR WAKE TO AM RADIO 1. After setting your desired wake up time, slide the POWER selector to ON position. 2. Slide the FUNCTION selector to AM position then rotate the TUNING knob to select your desired station and adjust the VOLUME knob to the desired listening level. 3. Slide the POWER selector to ALARM position. 4. When the wake up time is reached, the radio will be turn on. SETTING FOR WAKE TO FM RADIO 1. After setting your desired wake up time, slide the POWER selector to ON position. 2. Slide the FUNCTION selector to FM position then rotate the TUNING knob to select your desired station and adjust the VOLUME knob to the desired listening level. 3. Slide the POWER selector to ALARM position. 4. When the wake up time is reached, the radio will be turn on. SETTING FOR WAKE TO BUZZER 1. After setting your desired wake up time, slide the POWER selector to ALARM position. 2. Slide the FUNCTION selector to BUZZER position. 3. When the wake up time is reached, the buzzer will be sounding. 5

7 SETTING FOR WAKE TO EXTERNAL AUDIO DEVICE 1. Using 3.5 mm plug audio cable (not included) to connect the unit and your external device. 2. Turn on your external audio device. 3. After setting your desired wake up time, slide the POWER selector to ON position. 4. Slide the FUNCTION selector to AUX position then rotate the TUNING knob to select your desired station and adjust the VOLUME knob and/or your external audio device to the desired listening level. 5. Slide the POWER selector to ALARM position. 6. When the wake up time reaches, the unit will play your connecting external audio device. NOTE: This unit is not able to turn on your external audio devices. The external audio devices should be switched on when the wake up time reaches. SNOOZE OPERATIONS When the wake up time reaches, press the SNOOZE button, the unit will not play your desired wake up source and will start to play after 10 minutes. This function can be used repeatedly during alarm sounding period. SLEEP TIMER OPERATIONS You can program the sleep timer to play the unit from 1 to 90 minutes and then shut off automatically. 1. Slide the FUNCTION selector your desired listening source. 2. Slide the POWER selector to OFF position. 3. Press the SLEEP button, the display will show the remain time and the unit will be played for 90 minutes and then shut off automatically. 4. Press again the SLEEP button or hold the SLEEP button to select your desired sleep remain time. 5. Press the SNOOZE button, to cancel the sleep timer function. TECHNICAL SPECIFICATION Power supply V ~ 50Hz Output rating X 0.8W RMS Net weight Kg Frequency range FM MHz AM KHz Power consumption W 6

8 7