How To Use An Oven With A Gas Cooker

Transcription

1 005_03 Validity from serial number /2007 Instructions for installation, use and maintenance ELECTRIC FRYER SKF4E SKF6E SKF1E SKF2E SKF2E4 CF4E CF6E CF1E4 CF2E6 CF2E4 CFE15 CFE15D TF4E TF6E TF1E TF2E TF2E4 COPYRIGHT 2004 GIGA GRANDI CUCINE SRL

2 Models and dimensions page 3 INDEX Technical data 4 Installation instructions 5 Installation 5 Legal and technical requisites 5 Installation 5 Wiring 5 Unipotential 5 Start-up 5 Using the appliance 6 Ignition 6 Emptying the bath 6 Cleaning and taking care of the appliance 6 What to do if not using the appliance for a long time 6 What to do if something goes wrong 6 Maintenance 6 WEEE Directive 7 Wiring diagrams 8-12 Warning 13 2

3 Dimensions C B E D A E B C D A SKF2E4 TF2E4 400 x 615 x x 700 x 510 Weight approx. 21 kg Weight approx. 21 kg SKF1E SKF4E 400 x 615 x 270 Weight approx. 21 kg C B E D A TF1E TF4E 400 x 700 x 510 Weight approx. 21 kg SKF2E SKF6E 600 x 615 x 270 Weight approx. 33 kg C B E D A B E C D TF2E TF6E 600 x 700 x 510 Weight approx. 33 kg A CF2E4 400 x 700 x 875 Weight approx. 51 kg CF1E4 CF4E 400 x 700 x 875 Weight approx. 51 kg CF2E6 CF6E 600 x 700 x 875 Weight approx. 85 kg A B C D E Main switch Oil outlet drive Pilot lamp (voltage) Pilot lamp (resistences) Oil outlet CFE x 700 x 875 Weight approx. 53 kg CFE15D 800 x 700 x 875 Weight approx. 96 kg 3

4 Technical data The data plate is located on the front of the appliance and contains all the data needed for connecting it up to the mains electricity supply. TIPO/TYPE MOD. ART. N. N. CAT/KAT GAS/GAZ G30 G31 G20 G25 II2H3B/P P mbar II2H3+ P mbar II2H3+ P mbar II2L3B/P P mbar II2ELL3B/P P mbar II2E+3+ P mbar II2H3B/P P mbar I2E P mbar II2H3B/P P mbar II2H3+ P mbar SE FI DK CZ SK SI IT CH PT ES IE GB GR NL DE FR BE AT CH LU EE LV LT EE LV LT Qn kw MOD. m 3 /h I3B/P P mbar I3+ P mbar NO MT CY IS HU CY Predisposto a gas: - Gas preset: - Prevu pour gaz: Eingestelt für Gas: - Preparado para gas: - Geschuckt voor: V AC kw Hz MADE IN ITALY THE APPLIANCE MUST BE CONNECTED IN COMPLIANCE WITH THE LAWS IN FORCE AND INSTALLED IN A WELL-VENTILATED ROOM. READ THE INSTRUCTION MANUALS BEFORE INSTALLING AND USING THE APPLIANCE. THE APPLIANCE MUST BE INSTALLED BY QUALIFIED PERSONNEL. FRYER Model Dim.: LxWxH Voltage rating Power Lead wire / Section SKF1E - SKF4E 400 x 615 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 CF1E4 - CF4E 400 x 700 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 TF1E - TF4E 400 x 700 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 SKF2E - SKF6E 600 x 615 x kw 5 x 2.5 mm 2 or 4 x 6 mm 2 CF2E6 - CF6E 600 x 700 x kw 5 x 2.5 mm 2 or 4 x 6 mm 2 TF2E - TF6E 600 x 700 x kw 5 x 2.5 mm 2 or 4 x 6 mm 2 SKF2E4 400 x 615 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 CF2E4 400 x 700 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 TF2E4 400 x 700 x kw 5 x 1.5 mm 2 or 4 x 2.5 mm 2 CFE x 700 x kw 5 x 2.5 mm 2 or 4 x 6 mm 2 CFE15D 800 x 700 x kw 5 x 6 mm 2 or 4 x 10 mm 2 4

5 Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. Under no circumstances should abrasive substances be used. Fit the legs to the appliance; the appliance must be levelled using a spirit level. Slight irregularities can be levelled by adjusting the feet themselves. With table models, make sure that the base chosen is capable of supporting the weight of the appliance. The main switch or plug should be located in the vicinity of the appliance and easy of access. We recommend installing the machine under a range hood so that all the fumes are removed as quickly as possible. If the appliance is to be installed near walls, dividing walls, kitchen equipment or decorative pannelling, these should be in non-inflammable material or covered with non-inflammable material. Make sure that all fire prevention standards and safety precautions are strictly adhered to. Warning! MODEL CF1E4 - CF4E - CF2E4 - CFE15 If this model is going to be mounted on its own, it must be fixed to the floor. Fixing accessories are included. The appliance should be fitted following the indications given in the drawing below. 1 INSTALLATION INSTRUCTIONS RETRO ARRIERE BACK ATRÁS RÜCKSEITE ACHTERAAN Installation Installation, start-up and maintenance should only be carried out by expert personnel. All work required to install the appliance should be carried out in compliance with all local standards and regulations. The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions. Warning! In compliance with international regulations, when connecting the appliance to the mains power supply, a device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from the mains. Wiring When choosing the lead wire, make sure it has the following characteristics: it should be at least of the H07 RN-F type and its section should be large enough for the appliance (see "Technical specifications and dimensions", page 4). Wire entry on top models is on the back wall, and underneath all other models. In both cases the terminal board is at the front, behind the control panel. Pass the wire through the core hitch and wire clamp, plug the leads into their terminals on the board and secure them. The earth lead must be a little longerthan the others so that it is the last lead to disconnect if the wire clamp breaks. Unipotential The appliance must be connected up to a unipotential system. The connection screw is located on all top models at the back on the right hand side, while in other models it is located underneath the appliance on the right hand side. It is labelled. Warning! With Top models, carefully measure the distance between the appliance and the edge of the base (Fig. 2). Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: - Local accident prevention standards - Current CEI standards. Warning! The manufacturers cannot be held responsible for any damage due to inadequate or incorrect installation. Under such circumstances the guarantee will be considered null and void. Start-up Before using the appliance for the first time, thoroughly clean out the oil bath (see paragraph entitled Cleaning and Taking Care of the Appliance ). Check that the appliance is connected up properly and start according to instructions overleaf. 5

6 Warning! - Beware of inexpert handling! - Old and dirty oil or frying fat can represent a real fire hazard; make sure only new oil or frying fat are used each time you start frying. - The food you intend to fry should always be dry; wet food causes the oil to foam and overflow. - Frying excessively large quantities of food at a time also causes the oil to foam; never exceed 1.0 kg. - If the level of oil in the bath falls below the low level mark stamped on it, the risk of fire will increase. - Never leave the appliance on without any oil in it. The lid delivered with the appliance should always be kept within easy reach. In case of fire, it should be used to douse the flames. Ignition Check that the oil drain release is closed. Fill the bath with oil up to the level marked. Turn on the main switch upstream of the appliance. Turn the knob from 0 to any temperature between 100 C and 195 C; the pilot lights will come on. The green light means that the appliance is on, while the orange one indicates that the resistances are on. As soon as the required temperature is reached, the orange light will go off. To turn the appliance off, simply turn the knob back to '0'. Emptying the bath First of all a suitable bowl for emptying the oil into should be found. The bowl should be heat-resistant and designed not to allow the oil to spill when the bath is being emptied, since this could be very dangerous. A bowl with these requisites is available separately as an optinal extra from our sales department. Fit the drainage pipe as shown in the picture (2). Open the oil drain tap. Important With Top models, make sure you respect the distance between the appliance and the edge of the base. USING THE APPLIANCE CLEANING AND TAKING CARE OF THE MACHINE Warning! Never clean the appliance with jets of water, whether direct or pressurised. Allow the machine to cool down before cleaning Before starting to clean the appliance, disconnect from the mains. Using the hook provided (see drawing 3), you can lift out the elements to make cleaning the appliance easier and far more thorough. Lift the elements as far as they will go. To lower them after cleaning, press the button on the left hand side. All steel parts should be washed in warm water, using a neutral detergent, then rinsed thoroughly to eliminate any residual detergent. Dry using a dry cloth. Avoid using abrasive or corrosive detergents which could damage the steel. What to do if not using the appliance for a long time Thoroughly clean and dry the machine as described. Disconnect the power supply. What to do if something goes wrong If anything goes wrong, immediately turn the appliance off, then turn off the power supply at the switch located upstream of the appliance, and call the aftersales department. MAINTENANCE All maintenance should be carried out by qualified personnel only. Before carrying out any maintenance work, unplug the appliance or turn off the switch upstream of the appliance. 2 3 MAX 120 mm 6

7 THE 2002/96/EC DIRECTIVE (WEEE): information to users This informational note is meant only for owners of equipment marked with the symbol shown in Fig. A on the adhesive label featuring the technical specifications applied on the actual product (the label also giving the serial number). This symbol indicates that the product is classified, according to the regulations in force, as an item of electrical and electronic equipment and conforms to EU Directive 2002/96/EC (WEEE) meaning that, at the end of its service life, it must be treated separately from domestic waste, i.e. it must be handed in free of charge to a separate waste electrical and electronic equipment collection centre or returned to the reseller when buying a new equivalent item of equipment. The user is responsible for delivering the unit at the end of its life to the appropriate collection facilities. Failure to do so shall result in the user being subject to the penalties prescribed by the legislation in force on waste. Suitable separated collection so that the unit no longer used can be sent off for environmentally compatible recycling, treatment and disposal helps avoid possible negative effects on the environment and on health and facilitates the recycling of the product's component materials. For more detailed information on available collection systems, contact the local waste disposal service or the shop you purchased the unit from. Producers and importers fulfil their responsibility for environmentally compatible recycling, treatment and disposal both directly and by joining a collective scheme. 7

8 Wiring diagrams SKF1E SKF4E CF4E CF1E4 TF1E TF4E ma C2 F1 F2 R Line input terminal board Switch Microswitch Contactor Safety contactor Working thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance SKF2E SKF6E CF6E CF2E6 TF2E TF6E 8

9 Wiring diagrams SKF1E SKF4E CF4E CF1E4 TF1E TF4E ma C2 F1 F2 R Line input terminal board Switch Microswitch Contactor Safety contactor Working thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance SKF2E SKF6E CF6E CF2E6 TF2E TF6E 9

10 Wiring diagrams SKF2E4 CF2E4 TF2E4 R1 R A1 A A1 A2 T2 T3 T1 T1 1 2 P1 P2 1 2 P1 P2 ma T3 L1 L2 L3 N 400V 3N PE ma L1 L2 L3 PE 230 V 3 ma T1 T2 T3 /C2 R1 Line input terminal board Switch Microswitch Thermostat Safety thermostat Safety thermostat Contactor Resistance Green pilot lamp Orange pilot lamp 10

11 Wiring diagrams CFE R mc m C2 F2 F1 ma L1 L2 L3 N PE 400V 3N ma mc L1 L2 L3 PE 230V 3 ma mc C2 F1 F2 R Line input terminal board Commutating terminal board Switch Microswitch Safety contactor Adjusting contactor Adjusting thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance 11

12 Wiring diagrams CFE15D R R mc m mc m C2 C2 F2 F2 F1 F1 ma L1 L2 L3 400V 3N N PE ma L1 L2 L3 5 6 PE mc V 3 ma mc C2 F1 F2 R Line input terminal board Commutating terminal board Switch Microswitch Safety contactor Adjusting contactor Adjusting thermostat Safety thermostat Green pilot lamp Orange pilot lamp Resistance 12

13 NOTES 13

14 NOTES 14

15 NOTES 15

16 WARNING THE MANUFACTURER CANNOT BE HELD RESPONSI- BLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPRO- VEMENT, THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSI- BLE IF THE INSTRUCTIONS CONTAINED IN THIS MA- NUAL ARE NOT OBSERVED. GIGA GRANDI CUCINE S.r.l. - Via Pisana, Loc. Olmo SCANDICCI (FI) - ITALY - Tel (11 linee r.a.) - Fax info@gigagrandidicucine.it 16