TELEHANDLER ATTACHMENTS & ACCESSORIES GUIDE

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "TELEHANDLER ATTACHMENTS & ACCESSORIES GUIDE"

Transcription

1 TELEHANDLER ATTACHMENTS & ACCESSORIES GUIDE

2 Productivity. Efficiency. The bottom line. That s what your business is all about. And that s where Aftermarket Parts can help. This guide makes it easy for you to select the proper tool to achieve optimum performance for your SkyTrak, Lull, Gradall and telehandlers. With quality attachments and accessories, Aftermarket Parts is committed to putting your work above everything. So you can get the job done right and on time.

3 TABLE OF CONTENTS ATTACHMENTS 4 CARRIAGES Standard Carriage, Side-Tilt Carriage, Swing Carriage, Dual Fork Positioning Carriage, Side-Shift Carriage 12 BUCKETS Material Bucket, Grapple Bucket, 4-in-1 Bucket 16 TRUSS BOOM 18 TOWER 20 PLATFORMS Fork Mounted Work Platform, Personnel Work Platform 22 OTHER Fork Mounted Lifting Hook, Sheet Material Adapter, Bale Clamp, Round Fork Tines, Universal Skid Steer Adapter, Auger, Concrete Bucket FORKS 30 FORKS Pallet Forks, Cubing Forks, Lumber Forks ACCESSORIES 40 COVERS Cab Covers 41 KITS Vinyl Cab Enclosure Kits, Hard Cab Enclosure Kits, Wear Pad Kits, Chain Kits, Fender Kits, Hydraulic Pressure Testing Kits 48 CALIPER Fork Wear Caliper 49 TIRES Firestone Duraforce MH Tires

4

5 ATTACHMENTS

6 ATTACHMENTS STANDARD CARRIAGE The standard carriage is manufactured with high quality steel and is available in various sizes. This attachment is essential on most job sites, allowing operators to pick and place materials from pallets of concrete block to loads of lumber. CURRENT PRODUCTION STANDARD CARRIAGES Ordered through Aftermarket Parts or with new machine orders CARRIAGE SIZE 48 in. 50 in. 50 in. 50 in. 60 in. 72 in. APPROX. WEIGHT 417 lb. 460 lb. 526 lb. 471 lb. 497 lb. 549 lb. PART NO NOTES: Standard up-and-down tilt on horizontal plane Multiple fork options Previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) Previous generation Lull E-Series attachments may be used on current production Lull E-Series models (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) FORK PIN NO. (2) G5-18A * 619A 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER * Used with the Universal Quick Coupler. 4 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

7 NON-CURRENT PRODUCTION STANDARD CARRIAGES Ordered exclusively through Aftermarket Parts CARRIAGE SIZE 48 in. 48 in. 48 in. 50 in. 50 in. 50 in. 50 in. 50 in. 60 in. 60 in. 60 in. 60 in. 72 in. 72 in. 72 in. 72 in. 74 in. APPROX. WEIGHT 509 lb. 417 lb. 377 lb. 479 lb. 490 lb. 471 lb. 532 lb. 500 lb. 510 lb. 523 lb. 534 lb. 497 lb. 509 lb. 575 lb. 586 lb. 549 lb. 598 lb. PART NO S S S S S S S S S FORK PIN NO (2) G5-19A G6-23A G6-42A SERIAL NO. PRIOR TO GRADALL G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 5

8 ATTACHMENTS SIDE-TILT CARRIAGE Adding to the versatility of the telehandler, the side-tilt carriage keeps the load level even when the terrain isn t. The carriage tilts loads from side-to-side to allow for uneven landing areas like a roof or sloped bank. NOTES: Side-to-side tilt on vertical plane Standard up-and-down tilt on horizontal plane Previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) Previous generation Lull E-Series attachments may be used on current production Lull E-Series models (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) CURRENT PRODUCTION SIDE-TILT CARRIAGES Ordered through Aftermarket Parts or with new machine orders CARRIAGE SIZE 48 in. 48 in. 48 in. 50 in. 60 in. 72 in. APPROX. WEIGHT 606 lb. 817 lb. 660 lb. 343 lb. 472 lb. 677 lb. PART NO FORK PIN NO. (2) G5-18A * 619A 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER * Used with the Universal Quick Coupler. 6 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

9 NON-CURRENT PRODUCTION SIDE-TILT CARRIAGES Ordered exclusively through Aftermarket Parts CARRIAGE SIZE 48 in. 48 in. 48 in. 48 in. 50 in. 50 in. 50 in. 60 in. 60 in. 66 in. 72 in. 72 in. 72 in. 74 in. 74 in. APPROX. WEIGHT 640 lb. 763 lb. 700 lb. 607 lb. 678 lb. 844 lb. 343 lb. 1,047 lb. 472 lb. 820 lb. 800 lb. 948 lb. 677 lb. 920 lb. 1,028 lb. PART NO FORK PIN NO (2) GRADALL G5-19A G6-23A G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 7

10 ATTACHMENTS SWING CARRIAGE The swing carriage permits the operator to maneuver loads through openings and tight spaces like windows or scaffolding by swinging the carriage to the right or left. NOTES: Right and left 90 swing option Right and left 180 swing option Standard up-and-down tilt on horizontal plane Previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) Previous generation Lull E-Series attachments may be used on current production Lull E-Series models (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) CURRENT PRODUCTION SWING CARRIAGES Ordered through Aftermarket Parts or with new machine orders CARRIAGE SIZE 72 in. 72 in. APPROX. WEIGHT 1,154 lb. 1,868 lb. CARRIAGE SWING PART NO FORK PIN NO G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER 8 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

11 NON-CURRENT PRODUCTION SWING CARRIAGES Ordered exclusively through Aftermarket Parts GRADALL CARRIAGE SIZE 52 in. 72 in. 72 in. 72 in. 72 in. 72 in. 72 in. 72 in. 72 in. APPROX. WEIGHT 959 lb. 914 lb. 1,154 lb. 1,440 lb. 1,230 lb. 1,252 lb. 1,810 lb. 2,112 lb. 1,868 lb. CARRIAGE SWING PART NO FORK PIN NO G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 544C C 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 9

12 ATTACHMENTS DUAL FORK POSITIONING CARRIAGE The dual fork positioning carriage allows the operator to adjust the width between the forks without leaving the cab. CURRENT PRODUCTION DUAL FORK POSITIONING CARRIAGES Ordered through Aftermarket Parts or with new machine orders NOTES: Dual fork positioning carriages require auxiliary hydraulics Standard up-and-down tilt on horizontal plane Previous generation Lull E-Series attachments may be used on current production Lull E-Series models (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) CARRIAGE SIZE APPROX. WEIGHT INCLUDED FORK LENGTH PART NO. 50 in. 1,090 lb. 48 in S FORK PIN NO G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER 10 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

13 NON-CURRENT PRODUCTION DUAL FORK POSITIONING CARRIAGES Ordered exclusively through Aftermarket Parts CARRIAGE SIZE 50 in. 50 in. 50 in. APPROX. WEIGHT 1,000 lb. 1,000 lb. 1,090 lb. INCLUDED FORK LENGTH 42 in. 42 in. 48 in. PART NO S FORK PIN NO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C C-54 SIDE-SHIFT CARRIAGE The side-shift carriage moves the load left or right for precise placement. NOTES: Standard up-and-down tilt on horizontal plane Left and right side-shift CURRENT PRODUCTION SIDE-SHIFT CARRIAGES Ordered through Aftermarket Parts or with new machine orders CARRIAGE SIZE 48 in. 50 in. APPROX. WEIGHT 768 lb. 905 lb. PART NO FORK PIN NO A 723A NON-CURRENT PRODUCTION SIDE-SHIFT CARRIAGES Ordered exclusively through Aftermarket Parts CARRIAGE SIZE 50 in. PART NO FORK PIN NO G5-19A G6-23A G5-18A * * Used with the Universal Quick Coupler. NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 11

14 ATTACHMENTS MATERIAL BUCKET Use the material bucket to scoop and carry loose material and debris like gravel or dirt. The material bucket can also be used for clean up around the job site. Material buckets are not designed for digging. NOTES: Bucket teeth kits available for , and material buckets (purchase part number ) Bucket teeth, Part No , available in kits* (available for , , and ) Previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) Previous generation Lull E-Series attachments may be used on current production Lull E-Series models (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) CURRENT PRODUCTION MATERIAL BUCKET Ordered through Aftermarket Parts or with new machine orders BUCKET WIDTH 72 in. 72 in. 73 in. 83 in. 83 in. 96 in. 96 in. 96 in. 102 in. CAPACITY 1.0 cu. yd. 1.7 cu. yd. 1.0 cu. yd cu. yd cu. yd cu. yd 1.5 cu. yd 2.35 cu. yd. 2.0 cu. yd. APPROX. WEIGHT 733 lb. 838 lb. 710 lb. 639 lb. 940 lb. 712 lb. 899 lb. 1,014 lb. 1,089 lb. PART NO * * G5-18A 619A 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER 12 * Replacement cutting edge not available separately. NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

15 NON-CURRENT PRODUCTION MATERIAL BUCKET Ordered exclusively through Aftermarket Parts GRADALL BUCKET WIDTH 60 in. 60 in. 72 in. 74 in. 74 in. 83 in. 83 in. 96 in. 96 in. 96 in. 96 in. 96 in. 102 in. 102 in. CAPACITY.75 cu. yd..75 cu. yd. 1.0 cu. yd cu. yd cu. yd cu. yd cu. yd cu. yd 1.25 cu. yd cu. yd. 1.5 cu. yd cu. yd cu. yd. 2.0 cu. yd. APPROX. WEIGHT 465 lb. 500 lb. 733 lb. 643 lb. 675 lb. 639 lb. 940 lb. 712 lb. 795 lb. 540 lb. 899 lb. 1,041 lb. 720 lb. 1,089 lb. PART NO G5-19A G6-23A G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 13

16 ATTACHMENTS GRAPPLE BUCKET The grapple bucket uses hydraulic arms to secure bulky loads and materials. This feature is useful when cleaning up natural disaster sites and day-to-day job site scraps. Grapple buckets are not designed for digging. NOTES: CURRENT PRODUCTION GRAPPLE BUCKET Ordered through Aftermarket Parts or with new machine orders BUCKET SIZE 72 in. 83 in. 96 in. 96 in. CAPACITY 1.0 cu. yd cu. yd cu. yd cu. yd. APPROX. WEIGHT 1,096 lb. 1,403 lb. 1,554 lb. 1,514 lb. G5-18A PART NO A 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER Independent grapple arms require auxiliary hydraulics (except 619A, 723A, G5-19A or G6-23A) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) NON-CURRENT PRODUCTION GRAPPLE BUCKET Ordered exclusively through Aftermarket Parts GRADALL Includes load charts. BUCKET SIZE 83 in. 96 in. 96 in. 96 in. CAPACITY 1.96 cu. yd cu. yd cu. yd cu. yd. APPROX. WEIGHT 1,403 lb. 1,740 lb. 1,554 lb. 1,514 lb. PART NO S G5-19A G6-23A G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A G6-42P 534D-9 534D D 14 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

17 4-IN-1 BUCKET This bucket saves you time and money. The 4-in-1 bucket can be used for loading, leveling, bottom dumping or as a grapple bucket. 4-in-1 buckets are not designed for digging. CURRENT PRODUCTION 4-IN-1 BUCKET Ordered through Aftermarket Parts or with new machine orders BUCKET SIZE 81 in. 96 in. CAPACITY.78 cu. yd. 1.3 cu. yd. APPROX. WEIGHT 1,503 lb. 1,806 lb. PART NO A 723A NON-CURRENT PRODUCTION 4-IN-1 BUCKET Ordered exclusively through Aftermarket Parts BUCKET SIZE 81 in. 96 in. CAPACITY.78 cu. yd. 1.3 cu. yd. APPROX. WEIGHT 1,503 lb. 1,806 lb. PART NO G5-19A G6-23A NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 15

18 ATTACHMENTS TRUSS BOOM When lifting and lowering roof trusses, framing walls or steel beams into place, use the truss boom; available with or without a winch. NOTES: Truss boom with winch feature requires auxiliary hydraulics Previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) Previous generation Lull E-Series attachments may be used on current production Lull E-Series model (proper load charts required) New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) CURRENT PRODUCTION TRUSS BOOM Ordered through Aftermarket Parts or with new machine orders G5-18A 619A LENGTH ft. 12 ft. 12 ft. w/ Winch 15 ft. CAPACITY 1,433 lb. 2,000 lb. 2,000 lb. 2,000 lb. PART NO S S 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER 16 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

19 NON-CURRENT PRODUCTION TRUSS BOOM Ordered exclusively through Aftermarket Parts GRADALL G5-19A G6-23A LENGTH 3 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft. 10 ft ft. 12 ft. 12 ft. 12 ft. 15 ft. 15 ft. 15 ft. 15 ft. WINCH Yes No No No No Yes Yes Yes Yes No No No Yes No No No Yes CAPACITY 4,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 1,600 lb. 2,000 lb. 1,433 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. PART NO S S S G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 17

20 ATTACHMENTS TOWER The tower attachment increases mobility and efficiency on the job site. It allows the operator to move materials to a higher row of scaffolding by extending the vertical reach without any additional boom extension. CURRENT PRODUCTION TOWER Ordered through Aftermarket Parts or with new machine orders NOTES: Tower requires auxiliary hydraulics Available with side-tilt carriage + and Gradall Models equipped with tower with side-tilt carriage requires auxiliary electrics + Lull Model 1044C-54SII equipped with tower with side-tilt carriage requires second auxiliary circuit Available with side-shift 100 swing carriage New standardized attachments are compatible with previous generation SkyTrak and Lull E-Series models (proper load charts required) TOWER HEIGHT 8 ft. 8 ft. 8 ft. CARRIAGE TYPE Standard Side-Tilt Side-Tilt CARRIAGE WIDTH 50 in. 50 in. 50 in. INCLUDED FORK LENGTH None None None LIFTING CAPACITY 4,500 lb. 4,500 lb. 4,500 lb. PART NO FORK PIN NO G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER 18 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

21 NON-CURRENT PRODUCTION TOWER Ordered exclusively through Aftermarket Parts GRADALL TOWER HEIGHT 6 ft. 6 ft. 6 ft. 6 ft. 6 ft. 6 ft. 6 ft. 6 ft. 8 ft. 8 ft. 8 ft. 8 ft. CARRIAGE TYPE Standard Standard Standard Swing w/ S.S. Swing w/ S.S. Standard Swing w/ S.S. Swing w/ S.S. Standard Standard Side-Tilt Side-Tilt CARRIAGE WIDTH 48 in. 48 in. 66 in. 66 in. 66 in. 72 in. 72 in. 72 in. 50 in. 50 in. 50 in. 50 in. INCLUDED FORK LENGTH None None None 48 in. 60 in. None 48 in. 60 in. None None None None LIFTING CAPACITY 4,000 lb. 4,500 lb. 4,000 lb. 2,620 lb. 2,880 lb. 4,500 lb. 2,600 lb. 2,878 lb. 2,629 lb. 4,500 lb. 2,629 lb. 4,500 lb. PART NO FORK PIN NO N/A N/A N/A N/A G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 1044C C-54 SII SERIAL NO. PRIOR TO NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 19

22 ATTACHMENTS FORK MOUNTED WORK PLATFORM Simply slide the forks into the work platform pockets, secure the locking pins and begin lifting materials and people to working heights. NOTES: Only for use with 48 in. pallet forks Removable front rail 4 ft. x 8 ft. platform The only approved fork mounted platform for telehandlers 1,000 lb. capacity Side entry platform 3 lanyard attach points ANSI approved Fork pocket dimensions 2.5 in. x 5.5 in. x 48 in. CURRENT AND NON-CURRENT PRODUCTION FORK MOUNTED WORK PLATFORM Ordered exclusively through Aftermarket Parts or with new machine orders GRADALL VERSION English French ISO* PART NO S S S 619A 723A G6-42A G9-43A G10-55A G12-55A G5-19A G6-23A TF6-42 G6-42P 534D D D / 524D 534C9 534C10 544C 534D6 VERSION English French ISO* PART NO S S S E C-54 SII 644B B C C C D-34 * Spanish and Portuguese manuals include pictoral decals. * Spanish and Portuguese manuals include pictoral decals. 20 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

23 PERSONNEL WORK PLATFORM The quick attach personnel work platform provides the operator with more options. Lifting materials and people saves time and money. NOTES: 4 ft. x 8 ft. platform Controlled from operator cab Quick attach mounted ANSI approved 6 lanyard attach points Side entry 2,000 lb. capacity NON-CURRENT PRODUCTION PERSONNEL WORK PLATFORM Ordered exclusively through Aftermarket Parts GRADALL PART NO S S G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P 534D-9 534D D NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 21

24 ATTACHMENTS FORK MOUNTED LIFTING HOOK The lifting hook provides the operator with the ability to lift and lower suspended loads without removing the carriage. NOTES: Fork mounted lifting hook Not for use with cubing or block forks Maximum fork size 2.36 in. x 7.09 in. CURRENT AND NON-CURRENT PRODUCTION FORK MOUNTED LIFTING HOOK Ordered exclusively through Aftermarket Parts GRADALL LIFTING CAPACITY 8,000 lb. 12,000 lb. PART NO A 723A G5-18A G5-19A G6-23A G6-42A G9-43A G10-55A G12-55A G6-42P 522D / 524D 534D-6 534D-9 534D D 534C-9 534C C LIFTING CAPACITY 12,000 lb. PART NO E C-54 SII 644B B C C C-54 SII 644D NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

25 NOTES: SHEET MATERIAL May be used with standard, side-tilt, or swing carriage May be used with pallet or lumber forks S previous generation SkyTrak attachments may be used on current production SkyTrak models (proper load charts required) S previous generation Lull E-Series attachments may be used on current production Lull E-Series model (proper load charts required) ADAPTER The sheet material adapter is ideal for carrying large, flat materials such as drywall, steel plates, or plywood, limiting damage during transport. CURRENT PRODUCTION SHEET MATERIAL ADAPTER Ordered through Aftermarket Parts or with new machine orders PART NO. G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER S NON-CURRENT PRODUCTION SHEET MATERIAL ADAPTER Ordered exclusively through Aftermarket Parts GRADALL CARRIAGE SIZE 72 in. 72 in. 72 in. 72 in. N/A TYPE Swing Swing Swing Standard N/A PART NO S S G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 534D-9 534D D D 544D 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 23

26 ATTACHMENTS BALE CLAMP The bale clamp attachment is used in the agriculture industry, making it easy to maneuver hay or straw bales. The bale clamps can grab hay bales that are approximately 79 inches in diameter. NOTES: Spike-style bale clamp available (picture shown) Tube-style bale clamp available Conversion kits available CURRENT PRODUCTION BALE CLAMP Ordered through Aftermarket Parts or with new machine orders STYLE Tube Spike PART NO A 723A CURRENT PRODUCTION BALE CLAMP CONVERSION KIT Ordered through Aftermarket Parts or with new machine orders STYLE Spike to Tube Tube to Spike PART NO A 723A 24 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

27 ROUND FORK TINES The round fork tines allow for stability of the hay bale while maneuvering around objects. CURRENT PRODUCTION ROUND FORK TINES Ordered through Aftermarket Parts or with new machine orders PART NO A 723A NOTES: A work range of 4 ft. UNIVERSAL SKID STEER ADAPTER Increase your compact telehandler machine s versatility with the universal skid steer adapter. This adapter is compatible with many existing skid steer attachments. CURRENT PRODUCTION AND NON-CURRENT PRODUCTION UNIVERSAL SKID STEER ADAPTER Ordered through Aftermarket Parts or with new machine orders PART NO A 723A G5-18A G5-19A G6-23A NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 25

28 ATTACHMENTS AUGER An auger expands the functionality of a telehandler. Not only can it go up in the air but also down into the ground. With various auger bit sizes available, the operator can be precise in choosing one to best fit the task at hand. NON-CURRENT PRODUCTION AUGER BITS Ordered exclusively through Aftermarket Parts DIAMETER 6 in. 9 in. 12 in. 15 in. 18 in. 20 in. 24 in. 8 in. 12 in. 16 in. 18 in. DEPTH 50 in. 50 in. 50 in. 50 in. 50 in. 50 in. 50 in. 60 in. 60 in. 60 in. 60 in. PART NO * * * * * * * ** ** ** ** 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO NON-CURRENT PRODUCTION AUGER EXTENSION Ordered exclusively through Aftermarket Parts LENGTH 14 in. 24 in. NOTES: PART NO * REQUIRED: Auger Drive Motor, Part No & Adapter, Part No ** REQUIRED: Auger Drive Motor, Part No SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. 26 Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

29 CONCRETE BUCKET The concrete bucket can increase your job site efficiency by reducing the amount of time and personnel that are required to get concrete materials to elevated sites. / NOTES: Manual and auxiliary hydraulic options available Discharge hose options 36 in. x 36 in. NON-CURRENT PRODUCTION CONCRETE BUCKET Ordered exclusively through Aftermarket Parts CAPACITY.5 cu. yd. 1 cu. yd..5 cu. yd. 1 cu. yd. CONTROLS Manual Manual Hydraulic Hydraulic TYPE Quick Switch Mount Quick Switch Mount Quick Switch Mount Quick Switch Mount PART NO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO NON-CURRENT PRODUCTION CONCRETE BUCKET DISCHARGE HOSE Ordered exclusively through Aftermarket Parts HOSE LENGTH 4 in. 4 in. w/ Gate 6 in. 8 in. Rubber Side Discharge PART NO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 27

30

31 FORKS

32 FORKS FORKS There are three main fork types available: the pallet fork, the cubing fork and the lumber fork. A pallet fork is designed to handle palletized material and other loads that require transportation and placement. The cubing fork has a smaller width and is used to load, unload and place cubes of brick or block. The lumber fork has a wider width and is ideal for separating stacks of lumber. PALLET FORK LUMBER FORK CUBING FORK 30 Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

33 CURRENT PRODUCTION FORKS Ordered through Aftermarket Parts or with new machine orders TYPE Pallet Lumber Pallet (Sold as Set) Pallet (Side-Shift Carriage Only) Pallet (Side-Shift Carriage Only) Cubing (Sold as Set) Pallet (Sold as Set) Pallet Pallet Pallet Lumber Lumber Cubing EYE DIAMETER 2.25 in in in in in in in in in in in in in. 2 in. Pallet (Fork Positioning Carriage Only) FORK DIMENSIONS (IN.) 2 x 4 x x 6 x 60 2 x 5 x x 5 x 48 2 x 4 x 48 2 x 2 x 48 2 x 4 x x 4 x x 5 x x 6 x x 7 x x 6 x 60 2 x 2 x x 4 x 48 CAPACITY PER FORK AT 24 IN. LOAD CENTER 3,800 lb. 3,650 lb. 4,409 lb. (rated at 20 in. load center) 4,409 lb. (rated at 20 in. load center) 4,409 lb. (rated at 20 in. load center) 1,940 lb. 4,409 lb. (rated at 20 in. load center) 5,475 lb. 6,850 lb. 5,650 lb. 5,400 lb. 8,150 lb. 1,940 lb. 5,000 lb. PART NO S G5-18A 619A 723A G6-42A SERIAL NO AFTER G9-43A SERIAL NO AFTER G10-43A G10-55A G12-55A 6036 SERIAL NO AFTER 6042 SERIAL NO AFTER 8042 SERIAL NO AFTER SERIAL NO AFTER SERIAL NO AFTER 644E-42 SERIAL NO AFTER SERIAL NO AFTER 1044C-54 SII SERIAL NO AFTER Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 31

34 NON-CURRENT PRODUCTION FORKS Ordered exclusively through Aftermarket Parts TYPE Cubing Pallet (Swing Mast Carriage Only) Drywall Pallet Pallet Pallet Pallet Pallet Lumber Pallet (Swing Mast Carriage Only) Pallet Lumber Pallet Cubing Cubing Lumber Drywall EYE DIAMETER 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in in in in in. FORK DIMENSIONS (IN.) 2 x 2 x x 4 x x 4 x 48 2 x 4 x x 4 x x 6 x 48 2 x 6 x 48 2 x 6 x 60 2 x 6 x 60 2 x 6 x 60 2 x 6 x 72 2 x 6 x 72 2 x 6 x 96 2 x 2 x 48 2 x 2 x x 4 x x 4 x 48 CAPACITY PER FORK AT 24 IN. LOAD CENTER 1,500 lb. 2,500 lb. 2,500 lb. 4,000 lb. 5,475 lb. 4,500 lb. 5,000 lb. 5,000 lb. 5,650 lb. 5,650 lb. 5,000 lb. 5,000 lb. 3,750 lb. (rated at 48 in. load center) 1,940 lb. 1,940 lb. 3,050 lb. 2,500 lb. GRADALL G5-19A G6-23A PART NO H G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C 32 Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

35 NON-CURRENT PRODUCTION FORKS (CONT.) Ordered exclusively through Aftermarket Parts TYPE Pallet Pallet Pallet Pallet Pallet Pallet Lumber Lumber Lumber Pallet Cubing (Sold as Set) Pallet (Sold as Set) Pallet Pallet (Sold as Set) Pallet Pallet (Sold as Set) EYE DIAMETER 2.25 in in in in in in in in in in in in in in in in. FORK DIMENSIONS (IN.) 2.25 x 4 x x 4 x x 5 x x 5 x 48 2 x 6 x x 6 x x 6 x x 7 x x 6 x x 6 x 72 2 x 2 x 48 2 x 4 x 48 2 x 4 x x 4 x x 5 x 48 2 x 5 x 48 CAPACITY PER FORK AT 24 IN. LOAD CENTER 5,475 lb. 5,475 lb. 6,850 lb. 6,850 lb. 5,650 lb. 8,150 lb. 8,150 lb. 5,400 lb. 8,150 lb. 5,650 lb. 1,940 lb. 4,409 lb. (rated at 20 in. load center) 4,409 lb. (rated at 20 in. load center) 4,409 lb. 4,409 lb. (rated at 20 in. load center) 4,409 lb. (rated at 20 in. load center) GRADALL G5-19A G6-23A PART NO S G6-42A SERIAL NO. PRIOR TO G9-43A SERIAL NO. PRIOR TO G10-55A G12-55A TF6-42 G6-42P G6-42P 522D / 524D 534D-6 534D-9 534D-9 534D D D 544D 534C-9 534C C Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 33

36 NON-CURRENT PRODUCTION FORKS Ordered exclusively through Aftermarket Parts TYPE Pallet Pallet Lumber Pallet Lumber Pallet Pallet Cubing Cubing Cubing Pallet EYE DIAMETER in in in in in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. FORK DIMENSIONS (IN.) 2 x 4 x 42 2 x 4 x x 6 x 48 2 x 4 x x 6 x x 4 x 42 2 x 5 x 42 2 x 2 x 48 2 x 2 x 48 2 x 2 x x 4 x 48 CAPACITY PER FORK AT 24 IN. LOAD CENTER 4,000 lb. 4,000 lb. 4,000 lb. 4,000 lb. 4,000 lb. 5,000 lb. 5,000 lb. 2,000 lb. 2,000 lb. 2,000 lb. 3,000 lb. PART NO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

37 NON-CURRENT PRODUCTION FORKS (CONT.) Ordered exclusively through Aftermarket Parts TYPE Pallet Pallet Pallet Pallet Lumber Drywall Lumber Pallet Lumber Pallet EYE DIAMETER 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. 2 in. FORK DIMENSIONS (IN.) 2 x 4 x x 4 x x 4 x 48 2 x 5 x 48 2 x 6 x x 7 x x 7 x x 4 x x 5 x 60 2 x 5 x 60 CAPACITY PER FORK AT 24 IN. LOAD CENTER 4,000 lb. 5,000 lb. 5,000 lb. 5,000 lb. 5,000 lb. 5,000 lb. 5,000 lb. 5,000 lb. 3,000 lb. 5,000 lb. PART NO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 35

38 NON-CURRENT PRODUCTION FORKS (CONT.) Ordered exclusively through Aftermarket Parts TYPE Lumber Lumber Lumber Lumber Pallet Cubing Pallet Pallet (Swing Carriage Only) Pallet Lumber (Swing Carriage Only) Pallet (Swing Carriage Only) EYE DIAMETER 2 in. 2 in. 2 in. 2 in. 2 in in in in in in in. FORK DIMENSIONS (IN.) 2 x 6 x 60 2 x 6 x x 7 x x 7 x 60 2 x 5 x 72 2.x 2 x x 4 x 48 2 x 5 x x 5 x x 6 x 48 2 x 5 x 60 CAPACITY PER FORK AT 24 IN. LOAD CENTER 5,650 lb. 5,000 lb. 6,000 lb. 5,000 lb. 5,060 lb. 1,940 lb. 5,475 lb. 5,060 lb. 6,850 lb. 4,000 lb. 5,000 lb. PART NO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

39 NON-CURRENT PRODUCTION FORKS (CONT.) Ordered exclusively through Aftermarket Parts TYPE Lumber Lumber (Swing Carriage Only) Lumber Pallet Pallet (Fork Positioning Carriage Only) Pallet (Fork Positioning Carriage Only) Pallet (Fork Positioning Carriage Only) Pallet (Fork Positioning Carriage Only) Pallet (Fork Positioning Carriage Only) Pallet (Fork Positioning Carriage Only) EYE DIAMETER 2.25 in in in in in in in in in in. FORK DIMENSIONS (IN.) 2.25 x 6 x x 7 x x 7 x x 6 x 72 2 x 4 x 42 2 x 4 x 42 2 x 5 x 42 2 x 5 x 42 2 x 4 x 48 2 x 4 x 48 CAPACITY PER FORK AT 24 IN. LOAD CENTER 8,150 lb. 5,000 lb. 5,400 lb. 5,650 lb. 4,000 lb. 4,000 lb. 5,000 lb. 5,000 lb. 4,000 lb. 4,000 lb. PART NO (LH) (RH) (LH) (RH) (LH) (RH) 6036 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO E-42 SERIAL NO. PRIOR TO SERIAL NO. PRIOR TO C-54 SII SERIAL NO. PRIOR TO B B C C-42 / 1044C-54 6K-37 6K-42 8K-42 10K-42 / 10K D-34 Forks rated less than the attachment and/or machine capacity decrease the capacity of the attachment and machine to that of the forks. Forks rated more than the attachment and/or machine capacity do not increase the attachment or machine capacity. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 37

40

41 ACCESSORIES

42 ACCESSORIES CAB COVERS Protect your equipment and cab interior from water damage with a high-durability, waterproof cab cover. Cab covers are easy to install without any additional tools and include a 1-year limited warranty. The covers are exclusively offered by Aftermarket Parts for, SkyTrak and Lull model telehandlers. CAB COVERS Ordered through Aftermarket Parts GRADALL PART NO TF6-42 G6-42A G9-43A G10-43A G10-55A G12-55A G6-42P 534D-9 534D D E C-54 SII 40 NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit

43 VINYL CAB ENCLOSURE KITS The vinyl cab enclosure kits offer an extra layer of protection from the cold and rainy weather. The kits are easily installed with no additional tools required. NOTES: 1-year limited warranty Glass windshield and skylight Heater kits available separately VINYL CAB ENCLOSURE Ordered through Aftermarket Parts GRADALL DESCRIPTION Vinyl Cab Enclosure Kit Heater Kit Vinyl Cab Enclosure Kit Heater Kit Vinyl Cab Enclosure Kit Heater Kit Heater Kit Vinyl Cab Enclosure Kit Heater Kit Vinyl Cab Enclosure Kit PART NO S G6-42A G9-43A G10-43A G10-55A G12-55A TF6-42 G6-42P 534D-6 534D-9 534D D E C-54* * Due to serial number breaks, refer to parts manual for proper heater components. NOTE: Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator s cab. Can t find the attachment you are looking for? Contact your Aftermarket Parts representative at LIFT or visit 41

REACHING OUT DELIVERING POWER AND RELIABILITY

REACHING OUT DELIVERING POWER AND RELIABILITY JLG TELEHANDLERS JLG TELEHANDLERS REACHING OUT Your productivity is on the line the minute you climb into the telehandler cab. The lineup of JLG all-wheel steer telehandlers gives you all the power, reliability

More information

301.7D. Mini Hydraulic Excavator

301.7D. Mini Hydraulic Excavator 301.7D Mini Hydraulic Excavator Engine Weights Gross Power (ISO 14396) 17.9 kw 24.3 hp Operating Weight with Canopy 1610 kg 3,550 lb Net Power 13.2 kw 17.7 hp Operating Weight with Cab 1720 kg 3,792 lb

More information

1-800-698-5510 www.martatch.com

1-800-698-5510 www.martatch.com LOADER ATTACHMENTS SKIDSTEER ATTACHMENTS SNOW BLADES CUSTOM made attachments to fit any loader or skid steer 1-800-698-5510 www.martatch.com PRODUCT INDEX ATTACHMENTS Page Buckets 2-3 Bale Spears 4 Manure

More information

Cat Fusion Coupler System Wheel Loaders 938, 950, 962, 966, 972 H and K-series

Cat Fusion Coupler System Wheel Loaders 938, 950, 962, 966, 972 H and K-series Cat Fusion Coupler System Wheel Loaders 938, 950, 962, 966, 972 H and K-series Features Improved Machine Performance Unsurpassed Durability Increased Visibility Wide Range of Job Site Solutions Benefits

More information

Operators Manual 3 pt. hitch forklift

Operators Manual 3 pt. hitch forklift Wifo Farm Equipment Ltd. 4181 Boomer line St Clements Ont Phone 519-699-5658 Fax 519-699-5655 E-mail: sales@wifo.ca www.wifo.ca Operators Manual 3 pt. hitch forklift H150/1600, H200/1600, H240/1600 H280/1600,

More information

Buckets. Forks. Bale Handling. Pallet Forks. Grain Pushers. Safety Access Platforms. Pick Up Hitches. Headstocks/Adaptor Plates. Headstock Conversions

Buckets. Forks. Bale Handling. Pallet Forks. Grain Pushers. Safety Access Platforms. Pick Up Hitches. Headstocks/Adaptor Plates. Headstock Conversions Buckets Forks Bale Handling Pallet Forks Grain Pushers Safety Access Platforms Pick Up Hitches Headstocks/Adaptor Plates Headstock Conversions Snow Ploughs Weight Boxes Bag Lifters Brackets Trailers www.middevonmachinery.co.uk

More information

Hyster Tire Handling Solutions. Complete Line of Fork Truck Mounted Tire Handlers

Hyster Tire Handling Solutions. Complete Line of Fork Truck Mounted Tire Handlers Hyster Tire Handling Solutions Complete Line of Fork Truck Mounted Tire Handlers A Model to Fit Any Application: Why Hyster/Greenfield Tire Handlers Designed specifically for lift trucks and OPTIMIZED

More information

MATERIAL HANDLING ATTACHMENTS

MATERIAL HANDLING ATTACHMENTS 2013 MATERIAL HANDLING ATTACHMENTS 17499 S. Dolan St. Kincheloe, MI 49788 Phone: 1-800-236-0064 Attachments@Supfab.com V1.0 To our customers: Superior Fabrication Company, LLC (SFC) would like to thank

More information

PC18MR-3 PC20MR-3 PC27MR-3 PC30MR-3 PC35MR-3 PC45MR-3 PC55MR-3

PC18MR-3 PC20MR-3 PC27MR-3 PC30MR-3 PC35MR-3 PC45MR-3 PC55MR-3 PCMR-3 PC45MR-3 PC55MR-3 MR-3 SERIES COMPACT H YDRAULIC E XCAVATOR WALK-AROUND Photo may include optional equipment Performance and Versatility Komatsu HydrauMind hydraulic system Automatic load sensing

More information

JCB TELESCOPIC WHEELED LOADERS TM180 AND TM220

JCB TELESCOPIC WHEELED LOADERS TM180 AND TM220 JCB TELESCOPIC WHEELED LOADERS TM180 AND TM220 Incredible versatility is achieved through compact dimensions and the additional lift height provided by a telescopic boom The manoeuvrability of articulated

More information

4500 SERIES. 97% Customer Satisfaction Rating 98% Customer Loyalty Rating. #1 Selling Tractor in the World 5-year Powertrain Warranty

4500 SERIES. 97% Customer Satisfaction Rating 98% Customer Loyalty Rating. #1 Selling Tractor in the World 5-year Powertrain Warranty 4500 SERIES #1 Selling Tractor in the World 5-year Powertrain Warranty 97% Customer Satisfaction Rating 98% Customer Loyalty Rating DEMING PRIZE 2003 JAPAN QUALITY MEDAL 2007 ECONOMY - 4500 Series The

More information

Ground bearing pressure. Main boom (No xx) max. length High reach (1311.xx and 1008.xx) 272 ft Luffing jib (No xx) max.

Ground bearing pressure. Main boom (No xx) max. length High reach (1311.xx and 1008.xx) 272 ft Luffing jib (No xx) max. The operating weight includes the basic machine with crawlers, 2 main winches 26,500 lbs and 46 ft main boom, consisting of A frame, boom foot (18 ft), boom head (28 ft), 71,200 lbs basic counterweight,

More information

VOLVO WHEEL LOADERS BLOCK HANDLING

VOLVO WHEEL LOADERS BLOCK HANDLING VOLVO WHEEL LOADERS BLOCK HANDLING VOLVO S BEEN AROUND THE BLOCK With Volvo on the job, moving large, heavy blocks quickly and effi ciently is easily done. That s because Volvo block handlers are specially

More information

Agriculture Telescopic Handlers

Agriculture Telescopic Handlers Agriculture Telescopic Handlers 2 At home on the farm Whatever job you re doing on the farm, you can do it quicker and more easily with a Bobcat telescopic handler and the right attachment. Power, versatility,

More information

T53 SLAB BUNDLE EXTRACTOR ATTACHMENT

T53 SLAB BUNDLE EXTRACTOR ATTACHMENT T53 SLAB BUNDLE EXTRACTOR ATTACHMENT APPLICATION AND OPERATING GUIDE Distributed By: UNIT LOAD HANDLING SYSTEMS, INC. 2301 SO. MISSION CIRCLE, FRIENDSWOOD, TX 77546 PH: 281-992-2006 FX: 281-992-2040 EM:

More information

Sideloader Truck Models 9300 and 9400: Specification Sheet

Sideloader Truck Models 9300 and 9400: Specification Sheet Sideloader Truck Models 9300 and 9400: Specification Sheet Model 9300 and 9400 Trucks: Short Work Of Long Loads Reliable Maneuverable Durable. The Raymond Sideloader lets you store more in less space by

More information

Wire Security Partitions & Cages Specification Guide

Wire Security Partitions & Cages Specification Guide Wire Security Partitions & Cages Specification Guide www.cisco-eagle.com/barriers Wire Partitions It doesn t have to be complicated... Cisco-Eagle publishes fully-illustrated, priced fast to order units

More information

ES Series ELECTRIC SCISSOR LIFTS. 1930ES 2030ES 2630ES 2646ES 3246ES Compact Size and Narrow Width For Ease of Access

ES Series ELECTRIC SCISSOR LIFTS. 1930ES 2030ES 2630ES 2646ES 3246ES  Compact Size and Narrow Width For Ease of Access ES Series ELECTRIC SCISSOR LIFTS Compact Size and Narrow Width For Ease of Access CE Rated for Indoor/Outdoor Usage Larger Platforms and Higher Capacities 1930ES 2030ES 2630ES 2646ES 3246ES www.jlg.com

More information

JCB LOADALLS 506C, 506C HL, 508C SPEC LIFT AND PLACE TELESCOPIC HANDLERS. Construction Equipment

JCB LOADALLS 506C, 506C HL, 508C SPEC LIFT AND PLACE TELESCOPIC HANDLERS. Construction Equipment JCB LOADALLS 06C, 06C HL, 08C SPEC LIFT AND PLACE TELESCOPIC HANDLERS Construction Equipment JCB TELESCOPIC HANDLER 06C MAX. PAYLOAD: MAX. LIFT HEIGHT: 6000lbs (2722kg) 36ft 0in (11.0 meters) A D B C H

More information

ISEC Presentation November 5, 2014

ISEC Presentation November 5, 2014 ISEC Presentation November 5, 2014 Safety is not an Option Safe practices for construction equipment in scrap. Pat Reilly Volvo CE 2 Presentation Overview Safety is not an Option Equipment Safety in Scrap

More information

SKID STEER LOADERS VERTICAL-LIFT 2700V NXT2 3300V NXT2 4000V

SKID STEER LOADERS VERTICAL-LIFT 2700V NXT2 3300V NXT2 4000V SKID STEER LOADERS VERTICAL-LIFT 2700V NXT2 3300V NXT2 4000V IN THE BEGINNING What began in the 19th century as an agricultural implement manufacturer has grown into a 21st century compact equipment powerhouse

More information

Post Pounders & Post Hole Augers

Post Pounders & Post Hole Augers Post Pounders & Post Hole Augers High & Heavy Hitters Side Mast Our most popular model for all heavy and light duty post placement Ability to move sideways a total of 16 Four hammer head mounting positions

More information

» 30,000 to 60,000 lb. capacity» Single and tandem axle

» 30,000 to 60,000 lb. capacity» Single and tandem axle ROLL-OFF CABLE HOISTS Tel: 800.285.0666 sales@wastequip.com www.wastequip.com Extendable Tail (EX) cable hoists are ideal for areas with clearance issues that require a low loading height.» 30,000 to 60,000

More information

RT100 ROUGH TERRAIN CRANE DATASHEET - IMPERIAL. Features:

RT100 ROUGH TERRAIN CRANE DATASHEET - IMPERIAL. Features: ROUGH TERRAIN CRANE DATASHEET - IMPERIAL Features: Rated capacity: 100 ton @ 10 ft working radius Maximum boom length: 174 ft Maximum tip height: 183 ft Maximum hook height: 174.5 ft CONTENTS Key............................................................................................

More information

JOHN DEERE TURF & UTILITY PRODUCTS EQUIPMENT FOR COMPACT UTILITY TRACTORS 260 Backhoe Equipment for Base Machine

JOHN DEERE TURF & UTILITY PRODUCTS EQUIPMENT FOR COMPACT UTILITY TRACTORS 260 Backhoe Equipment for Base Machine 260 Backhoe Equipment for Base Machine 6 ft. 2 In. (1.89 m) Digging Depth One Double Acting Swing Cylinder 150 Degree Swing Narrow Control Console Two Lever Control Six Spool Control Valve Hydraulics 8

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS 2012/04/19 TECHNICAL SPECIFICATIONS Elite LOADER BOOMS Main boom: rectangular structure 6" x 8" (152 mm x 203 mm) made of high tensile steel Stick boom: rectangular structure 6" x 6" (152 mm x 152 mm)

More information

Boom and fly capacities for this machine are listed by the following sections:

Boom and fly capacities for this machine are listed by the following sections: Lifting Capacities Telescopic Hydraulic Truck Crane HTC 8650 50 ton (45.36 metric ton) and fly capacities for this machine are listed by the following sections: Fully Extended Outriggers Working Range

More information

STORAGE SYSTEMS PUSH BACK RACK SYSTEMS. Innovative Solutions for Storage and Material Handling Systems

STORAGE SYSTEMS PUSH BACK RACK SYSTEMS. Innovative Solutions for Storage and Material Handling Systems STORAGE SYSTEMS PUSH BACK RACK SYSTEMS Innovative Solutions for Storage and Material Handling Systems Konstant.com PUSH BACK OVERVIEW Konstant patented Push Pack rack system provides selectivity in the

More information

EXCAVATOR SAFETY TRAINING

EXCAVATOR SAFETY TRAINING EXCAVATOR SAFETY TRAINING INSPECTION CHECKLIST INSPECTION AREA INSPECTION RESULTS Sat. Unsat. N/A Comments Carrier & Car Body Rotation system Tracks Rollers Frame, welds, bolts Drive system Upper Structure

More information

THE NEXT GENERATION OF DRAINAGE PLOWS. BRON keeps you on grade and on the money.

THE NEXT GENERATION OF DRAINAGE PLOWS. BRON keeps you on grade and on the money. DRAINAGE PLOWS THE NEXT GENERATION OF DRAINAGE PLOWS It s here and it s ready for you with the latest features and technology built into the completely new BRON Drainage Plow. Drainage contractors are

More information

BUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof.

BUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof. BUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof. 1155 & 4155 LCL: Applies to all freight in less than container load quantities.

More information

FORK POSITIONERS. Side-Shifting Fork Positioners Heavy Duty. Premium Quality and Design T410Z T411Z T411BZ/BZI T411ZR

FORK POSITIONERS. Side-Shifting Fork Positioners Heavy Duty. Premium Quality and Design T410Z T411Z T411BZ/BZI T411ZR Side-Shiftg Fork Positioners Heavy Duty T410 T411 T411/I T411R FORK POSITIONERS Premium Quality and Design Heavy Duty Side-Shiftg Fork Positioners Fork positioners, along with sideshifters, are among the

More information

Xerox Nuvera Production System and Xerox igen Digital Production Press

Xerox Nuvera Production System and Xerox igen Digital Production Press January 2015 702P01084 Xerox Nuvera Production System and Xerox igen Digital Production Press Xerox Nuvera 100/120/144/157 EA Production System Xerox Nuvera 100/120/144 MX Production System Xerox Nuvera

More information

Chapter 10 - Scaffolding Systems

Chapter 10 - Scaffolding Systems Chapter 10 - Scaffolding Systems Contents Chapter 10 - Scaffolding Systems... 10-1 Check and Oil the Pump Jacks... 10-4 Set Pump Jack Brackets... Error! Bookmark not defined. Set Pump Jack Poles... 10-5

More information

303.5E CR, 304E CR, 305E CR, 305.5E CR

303.5E CR, 304E CR, 305E CR, 305.5E CR 303.5E CR, 304E CR, 305E CR, 305.5E CR Mini Hydraulic Excavators 303.5E CR 304E CR 305E CR 305.5E CR Engine Engine Model Cat C1.8 Cat C2.4 Cat C2.4 Cat C2.4 Net Power (ISO 9249) 23.6 kw (31.6 hp) 30 kw

More information

Chain Link Cantilever Gate Installation Manual

Chain Link Cantilever Gate Installation Manual Chain Link Cantilever Gate Installation Manual Introduction to Cantilever Gates: A cantilever gate is unique in that it 'cantilevers' itself to close an opening while being supported from only one end.

More information

LIFT TRUCK SPECIFICATIONS

LIFT TRUCK SPECIFICATIONS LIFT TRUCK SPECIFICATIONS RT50 2-Wheel Drive 4-Wheel Drive RT60 2-Wheel Drive 4-Wheel Drive RT80 2-Wheel Drive 4-Wheel Drive TABLE OF CONTENTS RT50 / RT60 / RT80 2-WD / 4WD Specifications / Dimensions.

More information

volvo excavators buckets

volvo excavators buckets volvo excavators buckets The perfect match. Shaped to perform The profile and optimized bucket entry makes it easier to penetrate the ground, release material and it gives increased wear-life. With a short

More information

Paul Van Buren, superintendent Kanawha Club Manakin Sabot, Virginia

Paul Van Buren, superintendent Kanawha Club Manakin Sabot, Virginia I haven t found another machine of its kind that can do what my Toro Dingo can do. We use our loader every day to move plants, rock and mulch around the course, as well as other tools and materials around

More information

Contents. TS180 Features

Contents. TS180 Features TS180 Towed Scraper Scraper Bowl Capacity Heaped 14.3 m 3 18.8 yd 3 Width of Cut, to Router Bits 3200 mm 10 ft 6 in Rated Load 20 800 kg 45,900 lb Capacity Struck 9.9 m 3 13 yd 3 Depth of Cut max 203 mm

More information

Directive 2006/42/EC. Classification of equipment used for lifting loads with lifting machinery

Directive 2006/42/EC. Classification of equipment used for lifting loads with lifting machinery 1(9) Updated June 2012 Classification of equipment used for lifting loads with lifting machinery This classification was approved by the Machinery ing Group as a basis for a consistent application of the

More information

Roll Handling By Jeff Damour CONVERTER ACCESSORY CORPORATION Wind Gap, PA USA

Roll Handling By Jeff Damour CONVERTER ACCESSORY CORPORATION Wind Gap, PA USA Roll Handling By Jeff Damour CONVERTER ACCESSORY CORPORATION Wind Gap, PA USA Introduction This presentation is a basic tutorial in the mechanics of roll handling. We will discuss: 1) What is roll handling?

More information

304.5. Mini Hydraulic Excavator

304.5. Mini Hydraulic Excavator 304.5 Mini Hydraulic Excavator Cat 3024 Naturally Aspirated Diesel Engine Flywheel Power 28 kw 38 hp Operating Weight: With cab 4595 kg 10130 lb With canopy 4475 kg 9866 lb 304.5 Mini Hydraulic Excavator

More information

CMEIG Engineering Position Paper. Guidance document Lifting with hydraulic excavators, and how Australian Standard AS :2008 Section 5 applies.

CMEIG Engineering Position Paper. Guidance document Lifting with hydraulic excavators, and how Australian Standard AS :2008 Section 5 applies. CMEIG Engineering Position Paper Disclaimer: CMEIG is a non-profit organisation sponsored by companies involved in the supply of products and services in the construction and mining equipment supply industry

More information

attachments attachments hydraulic excavator

attachments attachments hydraulic excavator This brochure is intended to present many of the that can help you maximize the profit potential of owning or renting a Gradall excavator. Consult your authorized Gradall dealer to find out exactly which

More information

Cat. Hydraulic Excavators. Skid Steer Loaders. Piercing Tip C series shears incorporate a bolt-on piercing tip a key feature for enhancing

Cat. Hydraulic Excavators. Skid Steer Loaders. Piercing Tip C series shears incorporate a bolt-on piercing tip a key feature for enhancing Cat Mobile Scrap & Demolition Shears Hydraulic Excavators Skid Steer Loaders Features: C series Shears with Bolt-on Piercing Tip! Bolt-on Piercing Tip C series shears incorporate a bolt-on piercing tip

More information

Dock Hardware & Accessory Products Catalog

Dock Hardware & Accessory Products Catalog Dock Hardware & Accessory Products Catalog Product Page # Product Page # Angle Brackets/Clips 8 Back Up Plate 5 Backing Plate/Hurricane Stop 10 Carriage Bolt Sets 4 Chain Retainer 10 Connector Pin Set

More information

IBC Tote Containment Sumps

IBC Tote Containment Sumps IBC Tote Containment Sumps DENIOS Provides More Models- and More Variety of IBC Totes Sumps than any other Manufacturer Painted, Galvanized, Stainless Steel, and Poly models available Models provide storage

More information

R a n - F lo. When Quality Counts

R a n - F lo. When Quality Counts R a n - F lo irrigati o n When Quality Counts Model 2600 Series II Plastic Mulch Layer Automatic Rotrak 2600 Features New style drip tape dispenser!! 64 Row centers and 70 hp FWD minimum. Category II,

More information

TRACTOR QUICK HITCH CATEGORY I

TRACTOR QUICK HITCH CATEGORY I TRACTOR QUICK HITCH CATEGORY I Assembly, Operation & Parts Manual January 2005 Form: Quickhitch.PM7 SAFETY INFORMATION To avoid accident or injury, do not allow anyone to operate this equipment without

More information

Work Tool Attachments PRODUCT LINE

Work Tool Attachments PRODUCT LINE Work Tool Attachments PRODUCT LINE Backhoe Loaders 416E 420E 430E 450E augers asphalt cutters blades brooms forks hammers material handling arms plows rakes vibratory plate compactors Augers Drive Shaft

More information

Wheatheart Post Pounder Features & Options Wheatheart Post Pounders are ideal for fencing, vineyard and orchard applications.

Wheatheart Post Pounder Features & Options Wheatheart Post Pounders are ideal for fencing, vineyard and orchard applications. Fencing Equipment Wheatheart Post Pounder Features & Options Wheatheart Post Pounders are ideal for fencing, vineyard and orchard applications. Heavyduty and hard hitting Low maintenance (no springs in

More information

Don t forget to ask about our Vehicle Specific Quick Install Brackets...they ll reduce installation time by up to 50%. Save time and money!

Don t forget to ask about our Vehicle Specific Quick Install Brackets...they ll reduce installation time by up to 50%. Save time and money! In Fifth Wheels Reese, the brand that started the RV towing industry, continues to lead it today. Over half the fifth wheels on the road are towed by Reese fifth wheel hitches, providing unmatched safety,

More information

Appendix 6145-T1 Forklift Use Practices

Appendix 6145-T1 Forklift Use Practices Appendix 6145-T1 Operators must perform a preoperational inspection of the forklifts and attachments in accordance with the equipment operating manual. They will immediately report any equipment deficiencies

More information

Asking Price: N/A Final Price: N/A OROPS BUCKET AUXILIARY HYDRAULICS GENERAL APPEARANCE. Good. Good

Asking Price: N/A Final Price: N/A OROPS BUCKET AUXILIARY HYDRAULICS GENERAL APPEARANCE. Good. Good Page 1 of 6 SPECIFICATIONS 2005 CATERPILLAR 247B Customer Owned Certified MULTI TERRAIN LOADERS Inspection Number: 1117842 Serial #: MTL01706 Date Created: 09/23/2013 02:53:31 PM CDT Engine Serial #: N/A

More information

12Q-48P 14Q-48P 10Q-48P 22Q-60P 08Q-48P 06Q-48P 20Q-60P 18Q-60P 4DH15- 4DH12- 4DH12- 4DH12- 4DH12- 4DH12- 4DH15- 4DH15-

12Q-48P 14Q-48P 10Q-48P 22Q-60P 08Q-48P 06Q-48P 20Q-60P 18Q-60P 4DH15- 4DH12- 4DH12- 4DH12- 4DH12- 4DH12- 4DH15- 4DH15- 4DML Series Omega Lift has been designing and manufacturing all-terrain lift trucks for a wide range of material handling applications for over 25 years enabling us to be at the forefront of lift truck

More information

Auxiliary Hydraulic Oil Cooler for Skid-steers 105,000 BTU s/hr.

Auxiliary Hydraulic Oil Cooler for Skid-steers 105,000 BTU s/hr. Auxiliary Hydraulic Oil Cooler for Skid-steers 105,000 BTU s/hr. Features = Rugged Roof-mounted Design = 12 Volt Heavy-duty Fan Speed Controller = 10-40 GPM Flow Capacity = Automatic Thermostatically Controlled

More information

VP SERIES VERTICAL PERSONNEL LIFTS

VP SERIES VERTICAL PERSONNEL LIFTS VP SERIES VERTICAL PERSONNEL LIFTS Drive Your Productivity to New Heights The JLG VP Series represents the future of personnel lifts. Driveable at full platform height, they ve created a whole new dimension

More information

JCB MINI EXCAVATOR 8025/8030/8035 ZTS

JCB MINI EXCAVATOR 8025/8030/8035 ZTS JB MINI EXAVATOR 05/030/035 ZTS OPERATING WEIGT: 5 kg (599 lb), 37kg (709 lb) & 35 kg (03 lb) NET ENGINE POWER: 0 kw (. hp) &.7 kw (30. hp) D F K G L I A B E J STATI DIMENSIONS Machine model 05 ZTS 030

More information

Worldwide network in over 40 countries.

Worldwide network in over 40 countries. Worldwide network in over 40 countries. April 2012 56 rue de Neuilly 93136 Noisy le Sec Cedex - France Tel : +33 (0)1 49 42 72 95 Fax : +33 (0)1 48 44 00 02 E-mail : contact@ptc.fayat.com PTC s vibrodrivers

More information

Technical data Hydraulic lift crane LR 1250

Technical data Hydraulic lift crane LR 1250 Technical data Hydraulic lift crane Complies with ANSI/ASME B 30.5 LR 1250 Serial number 135xxx Dimensions Basic machine with undercarriage R 28 7 11 6 31 10 19 10 9 10 27 1 63 53 15 1 59 24 8 28 7 12

More information

M26 T/30 T M40 T/50 T

M26 T/30 T M40 T/50 T M26 T/30 T M40 T/50 T Rough terrain specialist Capacity from 2600 kg to kg Lifting height from 3 m to 6 m 2- or 4-wheel drive models Motorization Turbo Euro III M: true rough terrain trucks The M trucks,

More information

I BEAM TRACK INSTALLATION

I BEAM TRACK INSTALLATION PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must

More information

TRIPLE-L. Trailers with the Power Deck Advantage

TRIPLE-L. Trailers with the Power Deck Advantage TRIPLE-L Trailers with the Power Deck Advantage What Makes TRIPLE-L Trailers Your Best Choice? Backed by the engineering expertise and innovation of a world-leading equipment manufacturer, the TRIPLE-L

More information

Telescopic Handler Attachments. Product Range

Telescopic Handler Attachments. Product Range Telescopic Handler Attachments Product Range 2 Far-reaching versatility No matter what sector you work in construction, agriculture, industrial, snow removal or landscaping a Bobcat telescopic handler

More information

LiftAlloy Chain Slings

LiftAlloy Chain Slings CHAIN SLING BASICS Slings Lift-All chain slings meet or exceed all OSHA, ASME B30.9 and NACM standards and regulations. chain slings, available in 80 for 7/32" and 7/8"- /4" and 00 for 9/32"-3/4", are

More information

THE LOG SPLITTER YOU WILL ENJOY USING.

THE LOG SPLITTER YOU WILL ENJOY USING. BY CENTRAL BOILER THE LOG SPLITTER YOU WILL ENJOY USING. STRYKER log splitters offer quality workmanship second to none. Because of their unique design and manufactured finish, they require much less power

More information

2. Crane standing on firm, horizontal ground.

2. Crane standing on firm, horizontal ground. The operating weight includes the basic machine with HD undercarriage, 2 main winches 300 kn with speed change gear and 11 m boom, consisting of A frame, boom foot (4 m), boom head section (6.4 m), boom

More information

Skid Steer Loader Buyer's Guide By the purchasing experts at BuyerZone

Skid Steer Loader Buyer's Guide By the purchasing experts at BuyerZone Skid Steer Loader Buyer's Guide By the purchasing experts at BuyerZone Skid steer loaders are one of the most versatile pieces of construction equipment you can buy. Their compact size, maneuverability,

More information

ENGINE POWERED 5-10t. ~ r"." - )5 F-ii'ii""i;~ CPCD50 CPCD60 CPCD70 CPCD80 CPCD100

ENGINE POWERED 5-10t. ~ r. - )5 F-ii'iii;~ CPCD50 CPCD60 CPCD70 CPCD80 CPCD100 HELl ENGINE POWERED 5-10t I; ~ r"." d- - )5 F-ii'ii""i;~ CPCD50 CPCD60 CPCD70 CPCD80 CPCD100 STANDARD SPECIFICATION Manufacturer HUI HELl ca., LTD. Model CPCD50 CPCD60 CPCD70 CPCD80 CPCD100 Load Capacity

More information

Container design and types

Container design and types Container technology can transport mainly piece goods over great distances. The strong container protects good during the transport, the standardized dimensions let them store in well defined stacks and

More information

Swing System. Sound Levels. Electrical System. Blade

Swing System. Sound Levels. Electrical System. Blade Engine Model Mitsubishi L3E NA Diesel Rated net power (ISO 9249) 13.5 kw 18.1 hp Gross power 14 kw 19 hp Meets U.S. EPA Interim Tier 4 emissions requirements. Swing System Machine swing speed 10.5 rpm

More information

PaLLe t trucks Lifting carts t r g in t if L 2435 6815 6836 6856 6842

PaLLe t trucks Lifting carts t r g in t if L 2435 6815 6836 6856 6842 l i f t i n g c a r t s Lifting carts The prograe for lifting, transporting and storage From the classical forklift trolley to the machine lifter, from furniture dollies to a chassis with 24 tons load

More information

Premium Conventional. General Tire Information. High quality; low operating cost. Pneumatic ride in extreme conditions.

Premium Conventional. General Tire Information. High quality; low operating cost. Pneumatic ride in extreme conditions. Tire and Overview Premium Conventional 185-9932 254 mm (10 419 mm (16.5 185-9933 304 mm (12 419 mm (16.5 High quality; low operating cost. Skid Steer Loader Tires 5436 XD 222-3962 254 mm (10 419 mm (16.5

More information

ENVIRONMENTAL HEALTH AND SAFETY. Aerial Lift Guidelines

ENVIRONMENTAL HEALTH AND SAFETY. Aerial Lift Guidelines ENVIRONMENTAL HEALTH AND SAFETY Aerial Lift Guidelines December 2010 Aerial Lift Guidelines TABLE of CONTENTS I. General II. III. IV. Roles and Responsibilities Personal Protective Equipment Operating

More information

308E2 CR SB. Mini Hydraulic Excavator with Swing Boom

308E2 CR SB. Mini Hydraulic Excavator with Swing Boom 308E2 CR SB Mini Hydraulic Excavator with Swing Boom Engine Weights Engine Model* Cat C3.3B Operating Weight with Cab 8400 kg 18,519 lb Net Power (ISO 9249) 48.5 kw 65 hp Operating Specifications *Engine

More information

MH 20/25-4 T. Buggie. Compact trucks with 4 wheel drive. Capacity 2000 kg and 2500 kg Overall height: less than 2 metres Semi-Rough-Terrain

MH 20/25-4 T. Buggie. Compact trucks with 4 wheel drive. Capacity 2000 kg and 2500 kg Overall height: less than 2 metres Semi-Rough-Terrain Compact trucks with 4 wheel drive Capacity 2000 kg and 2500 kg Overall height: less than 2 metres Semi-Rough-Terrain MH 20/25-4 T Buggie MH 20/MH 25-4 T Buggie, With the experience of its exclusive innovative

More information

7. PRINCIPAL STEPS 8. POTENTIAL HAZARDS 9. RECOMMENDED CONTROLS

7. PRINCIPAL STEPS 8. POTENTIAL HAZARDS 9. RECOMMENDED CONTROLS ACTIVITY HAZARD ANALYSIS (AHA) 1. Contract Number: 2. Contractor Name: 3. Date prepared: 4. Title/Activity Performed: FIXED SCAFFOLDING 5. Location: 6. Estimated Date of Completion: 7. PRINCIPAL STEPS

More information

Grain Vacs / Suction Blowers

Grain Vacs / Suction Blowers Grain Vacs / Suction Blowers Kongskilde Grain Vacs a Flexible and Dependable Conveying System Kongskilde has been developing and manufacturing grain blowers since 1949 and is today one of the leading producers

More information

Trailmowers Type Beskrivelse Pris excl. moms Pris inkl. moms

Trailmowers Type Beskrivelse Pris excl. moms Pris inkl. moms Trailmowers Type Beskrivelse Pris excl. moms Pris inkl. moms T11544* 44" TRAILMOWER - 11.5 HP Briggs & Stratton I/C, recoil start, center hitch with offset capability, rear discharge, optional remote operator

More information

RIGHT. www.wright-attachments.com

RIGHT. www.wright-attachments.com RIGHT www.wright-attachments.com RIGHT Wright Attachments is a family run Engineering Company that specialises in Material Handling Solutions, along side our popular range of attachments we have the knowledge

More information

Elvoron Home Elevator

Elvoron Home Elevator Creating An Accessible World Elvoron Home Elevator Design And Planning Guide www.garaventalift.com Please note: Dimensions provided in this Guide are for REFERENCE ONLY and should not be used for site

More information

Sample Written Program. For. Scaffolds

Sample Written Program. For. Scaffolds Sample Written Program For Scaffolds 1 Scaffold Safety Program (COMPANY NAME) Purpose The purpose of this safety policy and procedure is to establish guidelines for the protection of {COMPANY} employees

More information

MOBILE GANTRY CRANE SB Series 15 30 50 70 100 US Tons

MOBILE GANTRY CRANE SB Series 15 30 50 70 100 US Tons MOBILE GANTRY CRANE SB Series 15 30 50 70 100 US Tons Why being single is so good. Engineered for your unique lifting needs. You need to match the right machine to your operation not the other way around.

More information

303.5E2 CR, 304E2 CR, 305E2 CR, 305.5E2 CR

303.5E2 CR, 304E2 CR, 305E2 CR, 305.5E2 CR 303.5E2 CR, 304E2 CR, 305E2 CR, 305.5E2 CR Mini Hydraulic Excavators 303.5E2 CR 304E2 CR 305E2 CR 305.5E2 CR Engine Engine Model Cat C1.7 Cat C2.4 Cat C2.4 Cat C2.4 Net Power (ISO 9249) 17.5 kw (23.5 hp)

More information

IMPLEMENTS - "LARGE LOADERS" INDEX

IMPLEMENTS - LARGE LOADERS INDEX IMPLEMENTS - "LARGE LOADERS" INDEX EQUIPMENT DESCRIPTION LATEST REVISION PAGE NUMBER Index 09/01/14 1 Tractor & Loader: Farm Loader Compatibility Chart 09/01/14 2 Lift Cylinder & Frame Width Specifications

More information

OPERATOR S INSTRUCTION MANUAL

OPERATOR S INSTRUCTION MANUAL POWER JACK MATERIAL MOVER OPERATOR S INSTRUCTION MANUAL WARNING: Serious injury may result if this product is misused. The manufacturer provides the following instructions for use and care of this equipment

More information

Laser Positioning for Machines

Laser Positioning for Machines Laser Positioning for Machines Automatic Control and Visual Display Systems ROUGH GRADING FINE GRADING EXCAVATING BOX SCRAPER LAND LEVELING SKID STEER SURVEYING ROUGH GRADING FINE GRADING EXCAVATING BOX

More information

A Tractor Mounted Manure Loader

A Tractor Mounted Manure Loader South Dakota State University Open PRAIRIE: Open Public Research Access Institutional Repository and Information Exchange Bulletins South Dakota State University Agricultural Experiment Station 12-1-1944

More information

Cat. Buckets. 311 390 Hydraulic Excavators. Features: Designed as an Integral Part of the Cat System. Made to Last. Next Generation.

Cat. Buckets. 311 390 Hydraulic Excavators. Features: Designed as an Integral Part of the Cat System. Made to Last. Next Generation. Cat Buckets 311 390 Hydraulic Excavators Features: Designed as an Integral Part of the Cat System As Cat Excavators continue to set industry standards in general, quarry and heavy construction applications,

More information

Caterpillar Work Tool Product Line

Caterpillar Work Tool Product Line Caterpillar Work Tool Product Line Backhoe Loaders : 416E, 420E, 430E, 450E Torque @ 3625 psi Drive Method Augers A26B Pin-On 416E-430E 4212 [5711] Double Planetary A26B Pin-Lock 416E-430E 4212 [5711]

More information

Hydraulic. Scissor Lifts (989) Hydraulic Scissor Lifts

Hydraulic. Scissor Lifts (989) Hydraulic Scissor Lifts Hydraulic Scissor Lifts - Shop-Aid Series... 242 Scissor lifts Built to Your Specifications... 244 Typical Features & Options... 245-241 - Shop-Aid Series The Shop-Aid Series are expertly designed and

More information

Precision Vise Combinations

Precision Vise Combinations Precision Vise Combinations PanaVise vises and work holding tools have hundreds of uses limited only by your imagination! Each vise allows the head to Tilt, Turn & Rotate and position your work anywhere

More information

FORKLIFT STABILITY. MATERIAL HANDING AND ROBOTICS I. Practical course. Dávid HURI office door number: 324/6 huri.david@eng.unideb.

FORKLIFT STABILITY. MATERIAL HANDING AND ROBOTICS I. Practical course. Dávid HURI office door number: 324/6 huri.david@eng.unideb. FORKLIFT STABILITY MATERIAL HANDING AND ROBOTICS I. Practical course Dávid HURI office door number: 324/6 huri.david@eng.unideb.hu What is a powered industrial truck (P.I.T.)? Definition: A powered vehicle

More information

308E CR SB. Mini Hydraulic Excavator with Swing Boom

308E CR SB. Mini Hydraulic Excavator with Swing Boom 308E CR SB Mini Hydraulic Excavator with Swing Boom Engine Weights Engine Model Cat C3.3B Operating Weight with Cab 8333 kg 18,371 lb Net Power (ISO 9249) 48.5 kw 65 hp Operating Specifications Maximum

More information

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT

More information

Introduction. Rectangular Volume. Module #5: Geometry-Volume Bus 130 1:15

Introduction. Rectangular Volume. Module #5: Geometry-Volume Bus 130 1:15 Module #5: Geometry-olume Bus 0 :5 Introduction In this module, we are going to review the formulas for calculating volumes, rectangular, cylindrical, and irregular shaped. To set the stage, let s suppose

More information

JCB MIDI EXCAVATOR 8040 ZTS / 8045 ZTS

JCB MIDI EXCAVATOR 8040 ZTS / 8045 ZTS OPERATING WEIGHT: 9,480 lb (4,300 kg) 10,472 lb (4,750 kg) NET ENGINE POWER: 45 hp (33.1 kw) Interim Tier IV STATIC DIMENSIONS A Sprocket Idler Centers 6-1 (1845) 6-6 (1990) B Undercarriage Overall Length

More information

Contents. TS185 Features

Contents. TS185 Features TS185 Towed Scraper Scraper Bowl Capacity Heaped 14.5 m 3 19 yd 3 Width of Cut, to Router Bits 3785 mm 12 ft 5 in Rated Load 21 050 kg 46,400 lb Capacity Struck 11 m 3 14.4 yd 3 Depth of Cut max 305 mm

More information

Bath Planning Guidelines With Access Standards

Bath Planning Guidelines With Access Standards Bath Planning Guidelines With s 1: Door/Entry The clear opening of a doorway should be at least 32. This would require a minimum 2-10 door. If the existing structure precludes changing the opening then

More information