How to Order 3MA Series Cylinders for 1 1 / 2 " to 5" Bore 3MA cylinders can be specified by model number by using the table below.
|
|
- Jerome Woods
- 7 years ago
- Views:
Transcription
1 Tie Style Pneumatic s MA Series /" to 5".00 How to Order MA Series s for / " to 5" MA cylinders can be specified by model number by using the table below. C J MA U 4 A C Cushion Head End C Standard (cushioned head end) Blank Noncushioned head end ouble Specify K only if double rod cylinder is required. Mounting Style Specify mounting style code (see table on following page). Series MA Ports Standard (NPTF) Piston Type Blank Standard (lipseals and magnetic ring) Lipseals, no magnetic ring Lipseals, no magnetic ring (aluminum piston) Lipseals and magnetic ring (aluminum piston) 4 Bumper seals, no magnetic ring 6 Bumper seals and magnetic ring B Lipseals, /4" thick bumpers both ends H Lipseals, /4" thick bumper head end C Lipseals, /4" thick bumper cap end Lipseals and magnetic ring, /4" thick bumpers both ends F Lipseals and magnetic ring, /4" thick bumper head end R Lipseals and magnetic ring, /4" thick bumper cap end Seals Blank Standard (nitrile seals) E Fluorocarbon rod wiper and rod seal only Piston Number Standard (rod code number ) Special Modification Specify S only for special modification other than rod end, and then describe modification in item notes. Piston Thread Style 4 Small male 8 Intermediate male 9 Short female 55 For use with Split Coupler 4 Special (and specify all dimensions required) Stroke Length Specify stroke length required in inches. Cushion Cap End C Standard (cushioned cap end) Blank Non-cushioned cap end Piston Thread Type A Standard (UNF Unified Thread) W BSF British Fine M Metric (see page 04) Material Code Blank Standard Y 7-4 PH stainless steel J 0 stainless steel S 6 stainless steel Addition of ¼" bumper results in a ¼" stroke loss per bumper, per end. For example, a 6" stroke cylinder with ¼" bumpers at both ends (option B) has an effective stroke of 5½". Used for external chemical compatibility applications, not high temperature. Review Piston Selection Chart on page 4 to determine proper piston rod diameter. (Note: MA has only one rod diameter per bore size, so proper piston rod diameter from chart result may lead to bore size change). For oversize rod within the same bore size, please see 4MA section. 4 For additional information regarding this style, refer to page 0. If non-standard Material Code is required with this option, please place an S for special in Special Modification field and specify rod material in the item notes. How to order MA Series cylinders with sensors: Sensors must be ordered separately and are not mounted to the cylinder prior to shipment.. model number must have a Piston Type with a magnetic ring ((blank),, 6,, F or R).. Please refer to pages -8 for sensor part numbers and specifications. Global, Mini-Global, NAMUR and Weld Immune Sensors will fit the MA Series.. Style mounts and tie rod versions with Global Sensors will require tie rod bracket P8S-TMA0X. Please refer to page 5 for more information. 4 Parker Hannifin Corporation Pneumatic ivision
2 Tie Style Pneumatic s MA Series Supersedes Price List 099 Rev. dated 5/7/007 Base Pricing MA Series. Prices apply to standard, single or double rod models, with a choice of piston rod thread style 4, 8, 9 or 55. If piston rod thread style is not specified, style 4 will be furnished.. Base prices include cushions on both ends. For no-cushion on either end subtract the cushion deducter per end. (see column 5). Prices apply to any practical stroke length up to a maximum of 0" gross stroke with standard LA or LAF dimension, including fractional inches. 4. Heads and caps which will not utilize the F mount s tapped holes can be rotated to relocate the port 90 or 80 from position # at no additional charge. Please specify S in the Special Modification field and then describe new port location in the item notes. Cushion adjustment position rotates with port. 5. Standard mountings in different combinations are available. Consult Actuator ivision for pricing. Table A - Single End s im. "KK" Single s im. "CC" Base Price - Zero Stroke (Subtract) Thread Mounting Styles for Non- Thread Style 4 TEF BB, BC, Inch of ia. No. Cushion, Style 8 Male or (basic) BE* TB, TC, T NB J, H C CB Per End Male Style 9 Fraction T, TE, F G* Female /" 5/8" /-0 7/ (9.00) " 5/8" /-0 7/ (9.00) /" 5/8" /-0 7/ (6.50) /4" " 7/8-4 / (6.50) 4" " 7/8-4 / (0.00) 5" " 7/8-4 / NA (0.00) *Not available for 5" bore MA Table B - ouble End s im. "KK" ouble s im. "CC" Base Price - Zero Stroke (Subtract) Thread Mounting Styles for Non- Thread Style 4 KTEF Inch of ia. No. Cushion, Style 8 Male or (basic) KTB, KT KNB KJ KG KC KCB K Per End Male Style 9 KT, KTE, Fraction Female KF /" 5/8" /-0 7/ (9.00) " 5/8" /-0 7/ (9.00) /" 5/8" /-0 7/ (6.50) /4" " 7/8-4 / (6.50) 4" " 7/8-4 / (0.00) 5" " 7/8-4 / NA NA (0.00) 4 Parker Hannifin Corporation Pneumatic ivision
3 Tie Style Pneumatic s MA Series, Options Supersedes Price List 099 Rev. dated 5/7/007 Extra Charges for Model Code Options - MA Series Pricing option sequence generally follows the cataloged model code sequence The following charges should be added to the complete cylinder price as required. Table A - Model Code Options - Series (adder) and Piston Type MAJ Series adder Piston Type (blank = standard = no charge) MA with Lock (blank) 4 6 B H, C F, R Aluminum Aluminum Bumper Bumper /4" /4" /4" /4" Must order with Composite Composite Seals Seals Bumpers Bumpers Bumpers Bumpers No. ia. Cushions at Both Ends With No No With No Magnetic Both Ends, One End, Both Ends, One End, Single and ouble Magnetic Magnetic Magnetic Magnetic Magnetic Ring No Magnet No Magnet Magnet Magnet ( rod lock) Ring Ring Ring Ring Ring Add Add Add Add Add Add Add Add Add Add Add /" 5/8" " 5/8" /" 5/8" No Charge No Charge /4" " " " " " Table B - Model Code Options - Seals Ports Seals E = Fluorocarbon Seals Only No. ia. U = NPTF (no charge) Single ouble Standard NPTF Add Add /" 5/8" /8" " 5/8" /8" /" 5/8" /8" /4" " /" " " /" " " /" Table C - Model Code Options - Piston Ends Piston End Max. (Standard) Inch or Inch or Two Extra imension Fraction Fraction Wrench No. ia. Included in Base Over Over Flats Price* standard A standard A im. LAF im. im. LAF im. Add /" 5/8" /4" /4" " 5/8" /4" /4" /" 5/8" /4" /4" /4" " /8" /" " " /8" /" " " /8" /" *Special piston rod end threads and male rod ends, within the limits of the standard A and LA or LAF dimensions for the required rod diameter, will be furnished at no extra charge if the thread size is equal to a cataloged thread size. If the A dimension is increased, it must be accompanied by at least an equal increase in the LA or LAF dimension. When a female rod end is required, the W or WF dimension may be increased up to the equivalent standard male rod end LA or LAF dimension for the required rod diameter without any extra charge. Table - Model Code Options - Material Code Material Code* (blank) = Standard Material Y = 7-4PH Stainless Steel J = 0 Stainless Steel S = 6 Stainless Steel No. ia. Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Add Fraction Add Fraction Add Fraction Add Fraction /" 5/8" " 5/8" /" 5/8" No Charge /4" " " " " " *These adders apply to cylinders having stroke lengths up to 0" with standard LA or LAF dimension, and include hard chrome plating. On double rod cylinders, double the basic extra and per inch adders shown. 44 Parker Hannifin Corporation Pneumatic ivision
4 Tie Style Pneumatic s MA Series, Service Kits Supersedes Price List 099 Rev. dated 5/7/007 MA Service Kits (½" to 5" ) See MA/4MA Catalog AU0-099/NA for symbol identification, temperature range and fluid compatibility. PK - Piston Seal Kit, Standard Lipseals BK - Piston Seal Kit, Bumper Seals Magnetic Ring CH - Cushion Kit for either end Includes each of symbol & 8 Includes each of symbol & 8 Symbol Includes each of symbol 7, 7, 8, 0,, Includes wear band (#7) for aluminum pistons and 4" and 5" composite pistons (not replaceable for -/" to -/4" & Nitrile Seals Nitrile Seals bore composite pistons) Nitrile Seals Kit Number Price Kit Number Price Part Number Price Kit Number Price -/ PK50MA BK050MA CH500MA.00 PK00MA BK000MA CH000MA.50 -/ PK50MA BK050MA CH500MA.50 -/4 PK5MA0.00 BK05MA CH00MA PK400MA BK0400MA CH4000MA PK500MA BK0500MA CH5000MA 4.00 SK - Complete Kit Includes () each of symbol 5, 6, (or 4); () Standard Piston Seal Kit and () Cushion Kits Fluorocarbon Seals Only Nitrile Seals (all other Nitrile) Kit Number Price Kit Number Price -/ SK500MA 5.70 SK500MA SK000MA 54.0 SK000MA / SK500MA SK500MA /4 SK00MA 6.80 SK00MA SK4000MA SK4000MA SK5000MA 86.0 SK5000MA Parker Hannifin Corporation Pneumatic ivision
5 Tie Style Pneumatic s 4MA Series /" to 5".00 How to Order 4MA Series s for / " to 5" 4MA cylinders can be specified by model number by using the table below. J 4MA U 4 A ouble Specify K only if double rod cylinder is required. Cushion Head End Blank Non-cushioned head end C Cushioned head end (not available for 4ML) Series 4MA Air service 4ML Hydraulic service Mounting Style Specify mounting style code (see table on following page). Piston Type Blank Standard (lipseals and magnetic ring) Lipseals, no magnetic ring Lipseals, no magnetic ring (aluminum piston) Lipseals and magnetic ring (aluminum piston) (standard for 4ML) 4 Bumper seals, no magnetic ring 6 Bumper seals and magnetic ring B Lipseals, /4" thick bumpers both ends H Lipseals, /4" thick bumper head end C Lipseals, /4" thick bumper cap end Lipseals and magnetic ring, /4" thick bumpers both ends F Lipseals and magnetic ring, /4" thick bumper head end R Lipseals and magnetic ring, /4" thick bumper cap end Ports U NPTF R BSPP B BSPT T SAE Seals Blank Standard (nitrile seals) V Fluorocarbon seals 4 E Fluorocarbon rod wiper and rod seal only 5 4 Low temperature seals 4 M Metallic rod wiper, nitrile seals 6 Piston Number Specify rod code number for required diameter. 8, Special Modification Specify S only for special modification other than rod end, and then describe modification in item notes. (Includes 4MA with Linear Position Sensor Option) 7 Piston Thread Style 4 Small male 8 Intermediate male 9 Short female 55 For use with Split Coupler 9 Special (and specify all dimensions required) Stroke Length Specify stroke length required in inches. Cushion Cap End Blank Non-cushioned cap end C Cushioned cap end (not available for 4ML) Piston Thread Type A Standard (UNF Unified Thread) W BSF British Fine M Metric (see page 04) Material and Gland Code Blank Standard rod and gland H Standard rod and HI LOA gland Y 7-4 PH stainless steel rod and standard gland Z 7-4 PH stainless steel rod and HI LOA gland J 0 stainless steel rod and standard gland 0 K 0 stainless steel rod and HI LOA gland 0 S 6 stainless steel rod and standard gland 0 T 6 stainless steel rod and HI LOA gland 0 Not available with Linear Position Sensor Option (LPSO). Piston Types (blank),, 4 and 6 not available for 4ML. Piston Types (blank) and not available for oversize rod numbers and. Seals option V only available with Piston Types and 4. Seals option 4 only available with Piston Types and. Addition of ¼" bumper results in a ¼" stroke loss per bumper, per end. For example, a 6" stroke cylinder with ¼" bumpers at both ends (option B) has an effective stroke of 5½". 4 Reed and solid-state sensors only available with standard seals or options E and M. See footnote. 5 Used for external chemical compatibility applications, not high temperature. 6 If fluorocarbon seals are required with this option, please place an S for special in the Special Modification field and specify the fluorocarbon seals and metallic rod wiper in the item notes. 7 For Linear Position Sensor Option (LPSO), please include the following information for the Special Modification item notes: a. Sensor part number (see pages 98-0) b. Sensor position c. Port position (if other than position ) d. Length of stop tubing, gross stroke and net stroke (if required) Also, Piston Type option (blank),, 6,, F or R is required. 8 Review Piston Selection Chart on page 4 to determine proper piston rod diameter. 9 For additional information regarding this style, refer to page 0. If non-standard Material and Gland Code is required with this option, please place an S for special in Special Modification field and specify Material and Gland Code in the item notes. 0 Not available for 4ML. If a stop tube is required, specify gross stroke (net stroke + stop tube) in the model number, then place an S for special in the Special Modification field and specify the stop tube length in the item notes. Not available with Piston Types (blank) and. How to order 4MA/4ML Series cylinders with sensors: Sensors must be ordered separately and are not mounted to the cylinder prior to shipment.. model number must have a Piston Type with a magnetic ring ((blank),, 6,, F or R).. Please refer to pages -8 for sensor part numbers and specifications. Global, Mini-Global, NAMUR and Weld Immune Sensors will fit the 4MA/4ML Series.. Style mounts and tie rod versions with Global Sensors will require tie rod bracket P8S-TMA0X. Please refer to page 5 for more information. 46 Parker Hannifin Corporation Pneumatic ivision
6 Tie Style Pneumatic s 4MA Series 6" to 8" 6.00 How to Order 4MA Series s for 6" and 8" 4MA cylinders can be specified by model number by using the table below. J 4MA U 4 A ouble Specify K only if double rod cylinder is required. Cushion Head End Blank Non-cushioned head end C Cushioned head end (not available for 4ML) Mounting Style Specify mounting style code (see table on following page). Series 4MA Air service 4ML Hydraulic service Piston Type Blank Standard (lipseals, no magnetic ring) Lipseals and magnetic ring Ports U NPTF R BSPP B BSPT T SAE Reed and solid-state sensors only available with standard seals or options E and M. Used for external chemical compatibility applications, not high temperature. If fluorocarbon seals are required with this option, please place an S for special in the Special Modification field and specify the fluorocarbon seals and metallic rod wiper in the item notes. 4 For Linear Position Sensor Option (LPSO), please include the following information for the Special Modification item notes: a. Sensor part number (see pages 98-0) b. Sensor position c. Port position (if other than position ) d. Length of stop tubing, gross stroke and net stroke (if required) Also, Piston Type is required. 5 Review Piston Selection Chart on page 4 to determine proper piston rod diameter. 6 For additional information regarding this style, refer to page 0. If non-standard Material and Gland Code is required with this option, please place an S for special in Special Modification field and specify Material and Gland Code in the item notes. 7 Not available for 4ML. 8 If a stop tube is required, specify gross stroke (net stroke + stop tube) in the model number, then place an S for special in the Special Modification field and specify the stop tube length in the item notes. Seals Blank Standard (nitrile seals) V Fluorocarbon seals E Fluorocarbon rod wiper and rod seal only 4 Low temperature seals M Metallic rod wiper, nitrile seals Piston Number Specify rod code number for required diameter. 5 Special Modification Specify S only for special modification other than rod end, and then describe modification in item notes. (Includes 4MA with Linear Position Sensor Option) 4 Piston Thread Style 4 Small male 8 Intermediate male 9 Short female 55 For use with Split Coupler 6 Special (and specify all dimensions required) Stroke Length Specify stroke length required in inches. 8 Cushion Cap End Blank Non-cushioned cap end C Cushioned cap end (not available for 4ML) Piston Thread Type A Standard (UNF Unified Thread) W BSF British Fine M Metric (see page 04) Material and Gland Code Blank Standard rod and gland H Standard rod and HI LOA gland Y 7-4 PH stainless steel rod and standard gland Z 7-4 PH stainless steel rod and HI LOA gland J 0 stainless steel rod and standard gland 7 K 0 stainless steel rod and HI LOA gland 7 S 6 stainless steel rod and standard gland 7 T 6 stainless steel rod and HI LOA gland 7 How to order 6"-8" 4MA/4ML Series cylinders with sensors: Sensors must be ordered separately and are not mounted to the cylinder prior to shipment.. model number must have Piston Type.. Please refer to pages -8 for sensor part numbers and specifications. Global, NAMUR and Weld Immune Sensors will fit the 6"-8" 4MA/4ML Series.. Tie rod bracket P8S-TMA0X will be required for Global Sensors. Please refer to page 5 for more information. 47 Parker Hannifin Corporation Pneumatic ivision
7 Tie Style Pneumatic s 4MA Series, Base Supersedes Price List 099 Rev. dated 5/7/007 Base Pricing 4MA Series. Prices apply to standard, single or double rod models, with a choice of piston rod thread style 4, 8, 9 or 55. If piston rod thread style is not specified, style 4 will be furnished.. Prices apply to any practical stroke length up to a maximum of 0" gross stroke with standard LA or LAF dimension, including fractional inches.. Heads and caps which do not include mountings (or utilize the F mount s tapped holes) can be rotated to relocate the port 90º or 80º from position # at no additional charge. Please specify S in the Special Modification field and then describe new port location in the item notes. Cushion adjustment position rotates with port. 4. Standard mountings in different combinations are available. Consult Actuator ivision for pricing. Table A - Single End s im. "KK" Single s im. "CC" Base Price - Zero Stroke Thread Mounting Styles Add for Thread Style 4 BB, BC, Inch of Cushion ia. No. TEF* Style 8 Male or TB, TC, BE Per End NB J, H C CB *, B Male Style 9 T /" - 4" Fraction T, TE, F* Female G* /" " /" /4" 4" 5" 5/8" 5/8" 5/8" " " " /-0 /-0 /-0 7/8-4 7/8-4 7/8-4 7/6-0 7/6-0 7/6-0 /4-6 /4-6 / NA " " " /8" /8" /8" 7/8-4 7/8-4 7/8-4 /4- /4- /4- /4-6 /4-6 / NA NA ** C CB T TB, TC, J, H (6") BB, BC TE, TEF T, F JB, HB (8") BE (6"), B 6" 8" /8" /8" /4- / /4" /4" /- /- /4- / *Not available for /" bore with " rod diameter (rod no. ). **If required, add for cushion cap end only. Head end (rod end) cushion not available for /" bore with " rod diameter (rod no. ). Table B - ouble End s ouble s Base Price - Zero Stroke Mounting Styles /" " /" /4" 4" 5" KF* 5/8" /-0 7/ " 7/8-4 / NA 0.9 NA NA NA 5/8" /-0 7/ " 7/8-4 / /8" /-0 7/ " 7/8-4 / " 7/8-4 / /8" / " 7/8-4 / /8" / " 7/8-4 / NA NA /8" / NA NA " 8" ia. No. im. "CC" Thread Style 8 Male im. "KK" Thread Style 4 Male or Style 9 Female KTEF* KT, KTE, KTB, KT KNB KJ KT KTB, KT, KTE, KJ (6") KF KTEF KJB (8") KG KC KCB K K /8" / NA /4" /- / NA /8" / NA /4" /- / NA KG KC KCB K K Inch of Fraction Add for Cushion Per End 48 Parker Hannifin Corporation Pneumatic ivision
8 Tie Style Pneumatic s 4MA Series, Options Supersedes Price List 099 Rev. dated 5/7/007 Extra Charges for Model Code Options - 4MA Series Pricing option sequence generally follows the cataloged model code sequence The following charges should be added to the complete cylinder price as required. Table A - Model Code Options - Series (adder) and Piston Type ML Series adder* 4MAJ Series adder Piston Type (blank = standard = no charge) 400 PSIG Hydraulic 4MA with Lock (blank)** 4 6 B H, C F, R Service Option (only non-cushioned) /4" /4" Must order with Aluminum Aluminum Bumper Bumper /4" /4" Composite Composite Includes Standard Seals Seals Bumpers Bumpers Bumpers Bumpers No. ia. Cushions at Both Ends Seals (Nitrile & PUR) With No No With No Both Magnetic Both Ends, One End, One End, ouble Single and ouble Magnetic Magnetic Magnetic Magnetic Magnetic Ends, Single Ring No Magnet No Magnet Magnet ( rod lock) Ring Ring Ring Ring Ring Magnet Add Add Add Add Add Add Add Add Add Add Add Add Add 5/8" /" " NA No Charge No Charge /8" " " No Charge No Charge No Charge; No Charge; 5/8" /" Only Only " No Charge No Charge Available Available " /4" for No. for No. /8" No Charge No Charge " " /8" No Charge No Charge " " /8" No Charge No Charge /8" ** " /4" ** 6.05 No Charge /8" ** " /4" ** 4.90 *4ML available only with Piston Types,, B, H, C,, F or R. Composite pistons and bumper seals not available for 4ML. 4MAJ option not available with 4ML. **(blank) piston for 6" and 8" bore is aluminum, no magnetic ring, and is available at no additional charge. Composite pistons not available. Table B - Model Code Options - Ports and Seals Ports Seals V = Fluorocarbon Seals E = Fluorocarbon 4 = Low Temperature M = Metallic Wiper U = NPTF R = BSPP (all cylinder seals) Seals Only Seals No. ia. (no charge) B = BSPT T = SAE Relocation or Undersize or Extra Port* Single ouble Cushion** (Per End) Single ouble Single ouble Single ouble Standard Below Port Add Add Add Add Add Add Add Add Add /" " /" /4" 4" 5" 6" 8" 5/8" /8" " /8" /8" " /8" /8" " " /" /8" " /" /8" " /" /8" /8" /4" /4" /8" /4" /4" *NPTF port or cushions can be located on any side not occupied by mountings. Port relocation charge applies to heads and caps which cannot be rotated due to mountings. **Head end (rod end) cushion not available for /" bore with " rod diameter (rod no. ). Add for cushioned cap end only on single rod cylinders. Table C - Model Code Options - Piston Ends and Stop Tube Piston End Stop Tube** /" " /" /4" 4" 5" 6" 8" Non- Cushioned Max. (Standard) Inch or Inch or Two Extra Cushioned Head End Inch or imension Fraction Fraction Wrench or or Fraction of No. ia. Included in Base Over Over Flats Cushioned Cushioned Stop Tube Price* standard A standard Cap End Both Ends Length A im. LAF im. im. LAF im. Add Basic Extra - Add Add 5/8" /4" /4" " /8" /" /8" /4" /4" " /8" /" /8" /4" /4" " /8" /" " /8" /" /8" 5/8" /4" " /8" /" /8" 5/8" /4" " /8" /" /8" 5/8" /4" /8" 5/8" /4" /4" ' 7/8" /8" 5/8" /4" /4" " 7/8" * Special piston rod end threads and male rod ends, within the limits of the standard A and LA or LAF dimensions for the required rod diameter, will be furnished at no extra charge if the thread size is equal to a cataloged thread size. If the A dimension is increased, it must be accompanied by at least an equal increase in the LA or LAF dimension. When a female rod end is required, the W or WF dimension may be increased up to the equivalent standard male rod end LA or LAF dimension for the required rod diameter without any extra charge. ** Apply stop tube base adder & per inch charge to the complete cylinder price using the cylinder s net stroke. Only available for 4MA, 4ML and 4MAJ cylinders with aluminum pistons. 49 Parker Hannifin Corporation Pneumatic ivision
9 Tie Style Pneumatic s 4MA Series, Options Supersedes Price List 099 Rev. dated 5/7/007 Extra Charges for Model Code Options - 4MA Series Pricing option sequence generally follows the cataloged model code sequence The following charges should be added to the complete cylinder price as required. Table - Model Code Options - Material and Gland Code Material and Gland Code* Y = 7-4PH Stainless Z = 7-4PH Stainless (blank) = Standard H = Standard and Steel and Standard Steel and HI and Gland HI LOA Gland Gland LOA Gland No. ia. Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Add Fraction Add Fraction Add Fraction Add Fraction /" " /" 5/8" 5/8" 5/8" " " " " No /4" /8" Additional No Charge " Charge " /8" Per Inch " 6" 8" " /8" /8" /8" /4" /4" *These adders apply to cylinders having stroke lengths up to 0" with standard "LAF" dimension, and include hard chrome plating. On double rod cylinders, double the basic extra and per inch adders shown Material and Gland Code* J = 0 Stainless Steel K = 0 Stainless Steel S = 6 Stainless Steel T = 6 Stainless Steel and Standard and HI LOA and Standard and HI LOA Gland** Gland** Gland** Gland** No. ia. Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Basic Extra Inch of Add Fraction Add Fraction Add Fraction Add Fraction /" " /" /4" 4" 5" 6" 8" 5/8" 5/8" 5/8" " " " /8" /8" " " " /8" /8" /8" /4" /4" *These adders apply to cylinders having stroke lengths up to 0" with standard "LAF" dimension, and include hard chrome plating. On double rod cylinders, double the basic extra and per inch adders shown. **Option combination not available for 4ML 50 Parker Hannifin Corporation Pneumatic ivision
10 Tie Style Pneumatic s MA & 4MA Series Supersedes Price List 099 Rev. dated 5/7/007 Extra Charges for Other Common Modifications - MA and 4MA Series For these options, please specify S in the Special Modification field and then describe modification in the item notes. The following charges should be added to the complete cylinder price as required. Table A - Other Common Modifications TB, TC, T Mount SB*** Aluminum Round Tube, Aluminum Round Carbon Steel Round 8-8 (04) Stainless B Mount Non-standard BB Mount Carbon Steel Tie s Tube, 0 SS Tie Tube, Tie s & Steel Endcap lengths & Nuts Version s & Nuts Version Nuts Version Fasteners No. ia. Max. BB Length Included in Base Price Inch or Fraction of Extension* Extra Hex Nuts No Charge for mounts Inch of Fraction 5/8" /" " " 5/8" " /8" " 5/8" /" /8" " " /4" /8" /8" " 4" /8" /8" " 5" /8" /8" /8" 6" /6" No Charge /4" /8" 8" 5/6" No Charge /4" *The per inch adder shown includes all 4 studs extended an equal amount. **This option can be ordered with any mount except TE or TEF mount (no internal threads in fastener head). For mount, please use "0 SS Tie s & Nuts Version" pricing. ***SB mount uses the entire steel cap (painted) from Parker A Series Steel Air. s must include an aluminum piston option. For SB mount, see pages C06-07 in Pneumatic Actuator Products Catalog AU0-0900P-/NA for more information. Then add another F dimension measurement to OAL. Basic Extra Basic Extra Inch of Fraction Includes (8) Standard SHCS Fasteners** Cap Eye Mount (MP) Thin Cap Eye with Spherical Bearing Table B - Other Common Modifications Stroke Adjuster* Polypak Piston Boots*** Piston Stud Polypak Lipseal Infrequent Adjustment Pinned Lipseals PTFE Coated Style with Non- Gortite (50ºF max.) Piston to Standard Material Class Class 5 Class Class 5 Fiberglass (500ºF max.) Cushioned Cap End ** No. ia. (Fluorocarboncarbon) (Fluoro- Style 4 Style 8 (Nitrile) (Nitrile) Inch of Basic Inch of Inch of Basic Extra Basic Extra Extra Add Fraction Fraction Fraction End End End End /" 5/8" " " 5/8" " /8" /" $50.00 for " Style 8 rod " Available /4" stud, /8" per request applies to " at no " all bores /8" charge and rod " " /8" sizes " /8" /4" " /8" /4" *Only available for 4MA or 4MAJ with aluminum piston. Apply Basic Extra and Per Inch charges to the complete cylinder price using cylinder's GROSS stroke. **Only available with aluminum piston options and includes roll pin. If set screw is required, additional charges apply - contact the Actuator ivision *** boots require additional piston rod extension of the cylinder. Please see page C40 in the MA/4MA catalog to calculate this extension. To order this rod extension, please specify Thread Style "" with the newly calculated LA, LAF or WF dimension in the item notes. 5 Parker Hannifin Corporation Pneumatic ivision
11 Tie Style Pneumatic s MA & 4MA Series, Common Modifications Supersedes Price List 099 Rev. dated 5/7/007 Extra Charges for Other Common Modifications - MA and 4MA Series For these options, please specify S in the Special Modification field and then describe modification in the item notes. The following charges should be added to the complete cylinder price as required. Table C - Other Common Modifications Prepared for Shock Polymyte **Nu- Absorber* rod wiper Cushion Cap end only Piston Non-cushioned cap end All other seals Bumpers No. ia. shock absorber per model code per application and Both Ends describe in item notes End /" " /" /4" 4" 5" 6" 8" 5/8" 5/8" 5/8" " " " /8" /8" " " " /8" /8" /8" /4" /4" ***Par- Check Unit parallelmounted to cylinder Consult Actuator ivision for model and pricing * Only available for single rod end 4MA or 4MAJ with aluminum piston and non-cushioned cap end. Cap end mounts BB, BC and BE not available. Other cap end mount availability depends on shock absorber model. Some models may not fit the cylinder; please contact the Actuator ivision for assistance. Price includes all necessary machining and parts to prepare for () shock absorber. Multiply this adder by the number of shocks per cylinder. Please size shock absorber per the application and describe shock absorber model number in item notes. Shock absorber price added to complete cylinder price (as prepared for shock absorber). Shock absorber is installed to cylinder at factory. Please see Industrial Shock Absorbers Catalog AU08-0-/NA and Price List PL0 for more information. ** Only available for 4MA or 4MAJ with aluminum piston and non-cushioned both ends. Operating temperature -0 F to +50 F (-4 C to +66 C). Possible use with 4ML. Contact Actuator ivision for approval of media. *** Available for cylinder pressures up to 50 PSIG. Only available for T, C, F, TC, and B mounts. Please see pages 7-85 in Industrial Products Catalog for more information. Mounting kits can be sold separately from cylinder and Par-Check unit. Table - Internal Non-Rotational evice for 4MA, 4ML & 4MAJ Series Spline esign Base Price - Zero Stroke Add per inch of No. ia. Quantity / Add per Fraction 5 0 5/8" /" " /8" " " /8" /".70 " " /4" /8" " 4" /8" " 5" /8" Notes: Only available with aluminum piston and non-cushioned cap end. Maximum stroke length = 4. Piston rod torque not to exceed 0 ft-lb without Engineering ept. approval. For external non-rotating versions or higher torque values, please see the HB Series in Parker Pneumatic Actuator Products Catalog AU0-0900P-/NA and Price List PL0900P-. See Electronic Sensors Section for Linear Position Sensing Option (LPSO) Adder. Table F - Nodular Iron Gland Assembly ia. Basic Extra Add Note: only available with standard or fluorocarbon seals. HI LOA and Metallic Wiper options not available. 5/8" " /8" /4" Parker Hannifin Corporation Pneumatic ivision
12 (Revised 9//008) Tie Style Pneumatic s 4MA Series /" to 8", Service Kits Supersedes Price List 099 Rev. dated 5/7/007 4MA Service Kits (½" to 8" ) See MA/4MA Catalog AU0-099/NA for symbol identification, temperature range and fluid compatibility -/ -/ -/ ia. No. Standard Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 Nitrile Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 RG04MA006.0 RG04MA RGL4MA RG04MA RG04MA RGL4MA /8 RG04MA006.0 RG04MA RGL4MA RG04MA RG04MA RGL4MA /8 RG04MA006.0 RG04MA RGL4MA RG04MA RG04MA RGL4MA RG04MA RG04MA RGL4MA /8 RG04MA RG04MA RGL4MA RG04MA RG04MA RGL4MA /8 RG04MA RG04MA RGL4MA RG04MA RG04MA RGL4MA /8 RG04MA RG04MA RGL4MA /8 RG04MA RG04MA RGL4MA /4 RG04MA RG04MA RGL4MA /8 RG04MA RG04MA RGL4MA /4 RG04MA RG04MA RGL4MA / -/ -/ / -/ -/ ia. Kit Number Price Kit Number Price Kit Number Price 5/8 RG04MAH RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH /8 RG04MAH RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH /8 RG04MAH RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH /8 RG04MAH 6.00 RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH /8 RG04MAH 6.00 RG04MAH RGL4MAH RG04MAH RG04MAH RGL4MAH /8 RG04MAH 6.00 RG04MAH RGL4MAH /8 RG04MAH 6.00 RG04MAH RGL4MAH /4 RG04MAH7 0.0 RG04MAH75.40 RGL4MAH /8 RG04MAH 6.00 RG04MAH RGL4MAH /4 RG04MAH7 0.0 RG04MAH75.40 RGL4MAH ia. No. No. HI LOA Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 Nitrile Seals Fluorocarbon Seals Low Temp Seals Metallic Wiper Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 Nitrile Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 RG04MAM RG04MAM RGL4MAM RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM RGL4MAM RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM RGL4MAM RG04MAM RG04MAM RGL4MAM RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM5 8.0 RGL4MAM4 6.0 RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM5 8.0 RGL4MAM4 6.0 RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM5 8.0 RGL4MAM /8 RG04MAM RG04MAM5 8.0 RGL4MAM /4 RG04MAM RG04MAM RGL4MAM /8 RG04MAM RG04MAM5 8.0 RGL4MAM /4 RG04MAM RG04MAM RGL4MAM Standard & HI LOA Gland Metallic Wiper Gland (both tools required) Gland Wrench Gland Wrench Spanner Wrench ia. Part Number Price Part Number Price Part Number Price 5/ / / Parker Hannifin Corporation Pneumatic ivision
13 Tie Style Pneumatic s 4MA Series, Service Kits Supersedes Price List 099 Rev. dated 5/7/007 4MA Service Kits (½" to 8" ) See MA/4MA Catalog AU0-099/NA for symbol identification, temperature range and fluid compatibility Nitrile Seals PK - Piston Seal Kit, Standard Lipseals Includes each of symbol & 8 BK - Piston Seal Kit, Bumper Seals Includes each of symbol & 8 Includes wear band (#7) for aluminum pistons and 4" and 5" composite pistons Fluorocarbon Seals Low Temp Seals Nitrile Seals Fluorocarbon Seals Kit Number Price Kit Number Price Kit Number Price Kit Number Price Kit Number Price -/ PK504MA PK504MA05.90 PK504MA BK0504MA.0 BK0504MA PK004MA PK004MA PK004MA BK0004MA.0 BK0004MA / PK504MA PK504MA PK504MA BK0504MA.80 BK0504MA /4 PK54MA0.00 PK54MA PK54MA BK054MA 8.0 BK054MA PK4004MA PK4004MA PK4004MA BK04004MA 7.0 BK04004MA PK5004MA PK5004MA PK5004MA BK05004MA BK05004MA PK6004MA PK6004MA PK6004MA PK8004MA PK8004MA PK8004MA Magnetic Ring Symbol (not replaceable for -/" to -/4" bore composite pistons) Only with Nitrile Seals Part Number Price ia. No. SK - Complete Kit Includes each of Standard Gland Kit, Piston Seal Kit, Head Cushion Kit and Cap Cushion Kit Nitrile Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price -/ -/ -/ /8 5/8 5/8 -/8 -/8 SK504MA SK004MA SK504MA SK04MA SK4004MA SK5004MA SK6004MA SK8004MA SK504MA5 SK004MA5 SK504MA5 SK04MA5 SK4004MA5 SK5004MA5 SK6004MA5 SK8004MA SK54MAL4 SK04MAL4 SK54MAL4 SK4MAL4 SK404MAL4 SK504MAL4 SK604MAL4 SK804MAL /8 -/8 -/8 -/4 -/4 SK504MA* SK004MA SK504MA SK04MA SK4004MA SK5004MA SK6004MA SK8004MA SK504MA5* SK004MA5 SK504MA5 SK04MA5 SK4004MA5 SK5004MA5 SK6004MA5 SK8004MA SK54MAL4* SK04MAL4 SK54MAL4 SK4MAL4 SK404MAL4 SK504MAL4 SK604MAL4 SK804MAL *oes not include Head Cushion Kit (not available) 54 Parker Hannifin Corporation Pneumatic ivision
14 (Revised 9//008) Tie Style Pneumatic s 4ML Series, Service Kits Supersedes Price List 099 Rev. dated 5/7/007 4ML Service Kits (½" to 8" ) See MA/4MA Catalog AU0-099/NA for symbol identification, temperature range and fluid compatibility -/ -/ -/ Standard Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 No. ia. Nitrile & PUR Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA /4 RG04ML RG04ML RGL4MA /8 RG04ML RG04ML RGL4MA /4 RG04ML RG04ML RGL4MA / -/ -/ / -/ -/ ia. Nitrile & PUR Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 RG04MLH RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH /8 RG04MLH RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH /8 RG04MLH RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH /8 RG04MLH 5.0 RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH /8 RG04MLH 5.0 RG04MLH RGL4MAH RG04MLH0 0.0 RG04MLH RGL4MAH /8 RG04MLH 5.0 RG04MLH RGL4MAH /8 RG04MLH 5.0 RG04MLH RGL4MAH /4 RG04MLH RG04MLH RGL4MAH /8 RG04MLH 5.0 RG04MLH RGL4MAH /4 RG04MLH RG04MLH RGL4MAH ia. No. No. HI LOA Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 Metallic Wiper Gland Cartridge Kit Includes each of symbol 4, 40, 4 & 45 Nitrile & PUR Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 RG04MLM RG04MLM RGL4MAM RG04MLM RG04MLM RGL4MAM /8 RG04MLM RG04MLM RGL4MAM RG04MLM RG04MLM RGL4MAM /8 RG04MLM RG04MLM RGL4MAM RG04MLM RG04MLM RGL4MAM RG04MLM RG04MLM RGL4MAM /8 RG04MLM.0 RG04MLM5 6.0 RGL4MAM4 6.0 RG04MLM RG04MLM RGL4MAM /8 RG04MLM.0 RG04MLM5 6.0 RGL4MAM4 6.0 RG04MLM RG04MLM RGL4MAM /8 RG04MLM.0 RG04MLM5 6.0 RGL4MAM /8 RG04MLM.0 RG04MLM5 6.0 RGL4MAM /4 RG04MLM7 4.0 RG04MLM RGL4MAM /8 RG04MLM.0 RG04MLM5 6.0 RGL4MAM /4 RG04MLM7 4.0 RG04MLM RGL4MAM Standard & HI LOA Gland Metallic Wiper Gland (both tools required) Gland Wrench Gland Wrench Spanner Wrench ia. Part Number Price Part Number Price Part Number Price 5/ / / Parker Hannifin Corporation Pneumatic ivision
15 Tie Style Pneumatic s 4ML Service Kits Supersedes Price List 099 Rev. dated 5/7/007 4ML Service Kits (½" to 8" ) See MA/4MA Catalog AU0-099/NA for symbol identification, temperature range and fluid compatibility PK - Piston Seal Kit, Standard Lipseals Includes each of symbol, 9 & 8 Wear band (#7) for aluminum piston included Magnetic Ring Symbol Nitrile Seals Fluorocarbon Seals Low Temp Seals Only with Nitrile Seals Kit Number Price Kit Number Price Kit Number Price Part Number Price -/ PK504ML PK504ML PK504MA PK004ML0 9.0 PK004ML PK004MA / PK504ML PK504ML PK504MA /4 PK54ML0 4.0 PK54ML PK54MA PK4004ML0.0 PK4004ML PK4004MA PK5004ML0 5.0 PK5004ML PK5004MA PK6004ML PK6004ML PK6004MA PK8004ML0 9.0 PK8004ML PK8004MA SK - Complete Kit -/ -/ -/ Includes each of Standard Gland Kit and Piston Seal Kit No. ia. Nitrile & PUR Seals Fluorocarbon Seals Low Temp Seals Kit Number Price Kit Number Price Kit Number Price 5/8 SK504ML SK504ML SK54MAL SK504ML SK504ML SK54MAL /8 SK004ML SK004ML SK04MAL SK004ML 59.0 SK004ML5 9.0 SK04MAL /8 SK504ML SK504ML SK54MAL SK504ML SK504ML SK54MAL SK04ML 64.0 SK04ML SK4MAL /8 SK04ML 7.40 SK04ML5 9.0 SK4MAL4 9.0 SK4004ML 7.0 SK4004ML SK404MAL /8 SK4004ML SK4004ML SK404MAL SK5004ML 9.00 SK5004ML SK504MAL /8 SK5004ML SK5004ML SK504MAL /8 SK6004ML SK6004ML5.0 SK604MAL4.0 -/4 SK6004ML SK6004ML SK604MAL /8 SK8004ML 4.50 SK8004ML SK804MAL /4 SK8004ML.40 SK8004ML SK804MAL Parker Hannifin Corporation Pneumatic ivision
16 (Revised 9//008) Tie Style Pneumatic s MA & 4MA Mounting Kits & Accessories Mounting Kits Table A - Mounting Kits for /" thru 5" MA and 4MA Series s Supersedes Price List 099 Rev. dated 5/7/007 ia. J & H Part No. Price Part No. Price Part No. Price Part No. Price /" All L L L L " All L L L L /" All L L L L /4" All L L L L " All L L L L " All L L ia. CB Part No. Price Part No. Price Part No. Price /" All L L L " All L L L /" All L L L /4" All L L L " All L L L " All L L BB C (only for MA) BC G BE Accessories for ½" - 5" MA/MAJ Series; ½" - 8" 4MA/4ML/4MAJ Series s (The mating parts shown in the table below CANNOT to be used with any other cylinder series!). The following mounting accessories have been approved for use on MA / MAJ / 4MA / 4ML / 4MAJ Series cylinders and, when required, must be ordered in conjunction with these cylinders.. Order by part number below. Select Clevis or Eye Knuckle by thread size to fit the cylinder s piston rod end thread size as shown in table below.. Mating Clevis Brackets, Eye Brackets or Pivot Pins are listed in the same row of the Clevis or Eye Knuckle which they fit. 4. Pivot Pins must be ordered as separate items if used with Clevises or Eye Knuckles. Table A - Mounting Accessories Thread Part No. Price Part No. Price Part No. Price Part No. Price Part No. Price / / / / / / /" " /" /4", 4", 5" Clevis Eye Bracket Eye Knuckle Clevis Bracket Pivot Pin Mounting Plates for: BE Mount Part No. Price Part No. Price BB & BC Mount ", 8" Table B - Additional End Accessories Thread Linear Alignment Coupler Hex Jam Nut Part No. Price Part No. Price 7/ L / L / L / L L / L / L Parker Hannifin Corporation Pneumatic ivision
SMA Aluminum Cylinders
SMA Aluminum Cylinders PNEUMATIC TO 200 PSI HYDRAULIC 250 TO 400 PSI Non shock /8,, 2, 3 BORE SPACE SAVING AND CONVENTIONAL DESIGNS REPAIRABLE Very high quality Pancake type cylinders with all of the engineering
More informationCompact cylinder Double acting single rod type. SSD SSD-L (with switch) Double acting Compressed air 1.0. 1.6-10 to 60 (no freezing) Rc1/8 Rc1/4 Rc3/8
* U S 4 Specifications escriptions Bore size mm Actuation Working fluid ax. working pressure Pa in. working pressure Pa Withstanding pressure Pa Ambient temperature Port size Stroke length Rubber cushioned
More informationFDH Series Compact Finger Slides
FDH Series Compact Finger Slides Catalog #FDH- Prices effective September 1, 11 Cylinder block- Clear anodized aluminum Top Toolplate and Front Toolbar Clear anodized aluminum Tapped mounting holes ( for
More informationCylinders DIN ISO 6431 and VDMA 24 562
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO.
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type... 5/132...
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type...
More informationPneumatic Grippers Parallel and Angular Grippers. Catalog 1900-2/US
Pneumatic Grippers Parallel and Angular Grippers Catalog 19-2/US Catalog 19-2/US OContents GPR Series Rotary vane driven design GPR GPCR Series P5G-HPM(C) Series P5G-HP Series GPT Series P5G-AP Series
More informationPVM Piston Pumps Service Manual
PVM Piston Pumps Service Manual PVM018/020 PVM045/050 PVM057/063 PVM074/081 PVM098/106 PVM131/141 Table of Contents Service Parts Pump Description... 3 Basic pump Pump Operation Controls Types Part Identification...
More informationDESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4
DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD
More informationHH SERIES: HEAVY DUTY INDUSTRIAL HYDRAULIC TRD BIMBA. company
HH SERIES: HEAVY DUTY INDUSTRIAL HYDRAULIC TRD a BIMBA company The TRD difference... Precision machined throughout. We started in business as precision machinists. Every component is machined in a manner
More informationIMPORTANT DOCUMENTATION DO NOT DISCARD!
PART NO.: 6441-263C SERIES GRT 3 JAW PARALLEL GRIPPERS INFORMATION SHEET IMPORTANT DOCUMENTATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance
More informationPiston Accumulators. SK Series. Accumulator Catalog. Piston Types. Description. Sealing Systems. End Cap. O-ring. Sealing System. Piston.
SK Series Piston Types TYPE 2 pplication: Low-friction design for higher piston speeds, slow movements without stick-slip effect and high number of actuations (millions). ctual cycles achieved will vary
More informationIndex 11.1. Page. Pumping Systems...11.2-11.4 Intensifiers...11.5 Gas Boosters...11.6-11.7 High Pressure Generators...11.8-11.9
Pumping Systems, Intensifiers, Gas Boosters and High Pressure Generators High Pressure Equipment Company produces a number of components and systems for general industrial, elevated pressure applications.
More informationTN2000 Series Pneumatic Piston Actuators for DN125 to DN300 SPIRA-TROL Series Control Valves
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationActuators & Positioners LP - Linear Pneumatic Piston Actuator. Cylinder Actuators. High resolution, sensitivity, and fast response
Data Sheet DS/LP-EN Rev. F Actuators & Positioners LP - Linear Pneumatic Piston Actuator Cylinder Actuators High resolution, sensitivity, and fast response Available with 4 to 20mA position feedback Cylinders
More informationRUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
More information880 HYDRAULIC BENDER
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 880 HYDRAULIC BENDER Read and understand this material before operating or servicing this tool. Failure to understand how to safely operate this tool could
More informationChief S21M PARTS MANUAL. 2005 Chief Automotive Technologies
Chief SM 00 Chief Automotive Technologies Chief s Limited One-Year Warranty & Liability CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies, Inc. warrants for one year from date
More informationFlow Control Valves. Note: Also see R04C3 on page DC1. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Catalog HY15-352/US Contents Control SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI NEED VALVES J2A2... C8-2... Needle Valve, Cartridge Type...45/12... 42/6... 5-6 NVH81... C8-2... Needle
More informationOriginal Line Cylinders
Original Line Original Line How to Order Introduction to Bimba Standard Air Three-Position Air with Adjustable Cushions MRS Non-Rotating Air PC Steel Non- Original Line Steel (Bell Ring Style) Original
More information2H Hydraulic Cylinders. Heavy Duty NFPA Tie Rod Cylinders for Working Pressures up to 210 bar
H Hydraulic Cylinders Heavy Duty NPA for Working Pressures up to 0 bar Catalogue H07-0/U Mounting Styles H Series H Cylinder Mounting Styles The standard range of Parker H cylinders comprises 7 mounting
More informationJames M. Pleasants Company
James M. Pleasants Company SUBMITTAL DATA GAINESVILLE MECHANICAL DECEMBER 20, 2013 PROJECT: GSU: J-183 HUMANITIES LAW BLDG. QUOTE NO:12116 ENGINEER: STEVENS & WILKINSON GASKETED PLATE HEAT EXCHANGER Tag:
More information550658 D. PARAMETER SPECIFICATION Measured Variable: Displacement
T E M P O S O N I C S L S E R I E S LH 550658 D P r o d u c t S p e c i f i c a t i o n s Temposonics L Series position sensors are available with analog outputs (voltage or current) or digital outputs
More informationWorking Drawing and Assemblies. Chapter 10
Working Drawing and Assemblies Chapter 10 Objectives 1.Define working drawings. 2. Describe how working drawings are used in industry. 3. List the major components of a complete set of working drawings.
More informationISORIA. Centered disc butterfly valves with AMRING elastomer liner. 240 PSI: 1½ to8. 150 PSI : 10 to 24
Type series booklet 8448.1/2-EN--US ISORIA Centered disc butterfly valves with AMRING elastomer liner 240 PSI: 1½ to8 150 PSI : 10 to 24 Design in accordance with ISO 10631 Manual, electrical, pneumatical
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationHOW TO ORDER SAFETY PRODUCTS/SAFETY CONTROL SYSTEMS ELECTRICAL SAFETY CONTROLS
HOW TO ORDER SAFETY PRODUCTS/SAFETY CONTROL SYSTEMS PNEUMATIC SAFETY CONTROLS BASIC CONTROLS SC3000 - SELF CONTAINED 2 HAND CONTROL - STAND ALONE MODEL SC3300 - SELF CONTAINED 2 HAND CONTROL - PRESS READY
More informationSCION tc 2005-2008 COIL OVER SUSPENSION Preparation
SCION tc 2005-2008 COIL OVER SUSPENSION Preparation Part Number: PTR11-21070 NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item # Quantity Reqd. Description
More informationFisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation
Instruction Manual 1052 Size 20 Actuator (F & G) Fisher 1052 Size 20 Diaphragm Rotary Actuator with F and G Mounting Adaptation Contents Introduction... 1 Scope of manual... 1 Description... 1 Specifications...
More informationDOUBLE GATE KNIFE GATE VALVE
DOUBLE GATE KNIFE GATE VALVE The model knife gate is a bi-directional valve widely used in the Pulp and Paper industry (recycling or secondary fibre processing) designed to handle high concentrated or
More informationExtruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 62
1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 62 Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80,
More informationCOMMON WEAR PARTS & QUICK REFERENCE PARTS BREAKDOWN
COMMON WEAR PARTS & QUICK REFERENCE PARTS BREAKDOWN SERIES MECHANICAL SWEEPERS pn GS328985 REV B MAY 2012 COPYRIGHT 2012 GLOBAL ENVIRONMENTAL PRODUCTS, INC. ALL RIGHTS RESERVED REV B MAY 2012 Page 2 Common
More informationT-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5. www.thomsonlinear.com
T-Series Precision Linear Actuators Installation and Service Manual DW110353GB-1018 - EDITION 5 www.thomsonlinear.com Version History Edition Number Edition Date Reason for Revision 1 2004 First edition
More informationWorking Pressure - Hose Ends
Working Pressure - Hose Ends The maximum dynamic working pressure of a hose assembly is the lesser of the rated working pressure of the hose and the end connection used. HIGH SPECIALTY HOSE ACCESSORRIES
More informationMetric Hydraulic Cylinders. Series HMI
Metric Hydraulic Cylinders aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Catalog HY085/NA Parker As the world leader
More informationCylinders Series 40. Double acting, cushioned, magnetic ø160-200 - 250 (DIN/ISO 6431)
Cylinders Series 40 Double acting, cushioned, magnetic ø60-200 - 250 (DIN/ISO 643)»»» DIN/ISO 643 VDMA 24562 Rolled stainless steel rod Adjustable cushioning The cylinders Series 40 with diameters 60,
More informationHigh Pressure Equipment Pressure Vessels and Reactors Index
Pressure Vessels and Reacrs High Pressure Equipment Company designs and manufactures a broad range of pressure vessels and reacrs for both bench-scale and pilot plant applications. We have over 0 standard
More informationISO/VDMA Actuators. Engineering GREAT Solutions
ISO/VDMA Actuators Engineering GREAT Solutions 02 ISO/VDMA Actuators Contents 03 Introduction 04 ISO/VDMA Actuators 06 The ISO/VDMA Range 08 Industrial Options 10 Cleanline Options 12 IVAC innovation to
More informationDYNA RIDER FOOTBOARD KIT
-J0 REV. 0-0-0 DYNA RIDER FOOTBOARD KIT GENERAL Kit Number 000 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationCHROME FRONT BRAKE MASTER CYLINDER KIT
-J075 REV. 009-0-0 CHROME FRONT BRAKE MASTER CYLINDER KIT GENERAL Kit Number 5-99D, 5-99D Models These Chrome Master Cylinder Kits are designed to replace the original equipment front brake master cylinder
More informationPipe Thread Types and Designations
Pipe Thread Types and Designations Overview: Different types of screw threads have evolved for fastening, and hydraulic systems. Of special concern are plastic-to-metal, taper/parallel threaded joints
More informationSpira-trol TM Two-port Control Valves EN Standard KE, KF and KL DN15 to DN300 and ASME Standard KEA, KFA and KLA ½" to 12"
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
More informationNorbro Series 40R Pneumatic Actuator Double Acting or Spring Return
Pneumatic Actuator Double Acting or Spring Return Since the mid-sixties the Norbro name has been recognised as the leading quarter turn actuator for industry. As proof of this, Norbro pneumatic actuators
More informationThese features have made Lo Torc valves the choice of high pressure plug value users, worldwide:
LO TORC Plug Valve The high value, dependable performance, and low maintenance requirements of Halliburton Lo Torc valves can help reduce overall operating costs and help cut downtime. These features have
More informationTY-FLO Needle Valves
Design/Features Hard (Vee) or Delrin Soft Seat/Tip Orifice sizes from.17 to.438 in. Flow Coefficients (C V ) from.37 to.7 Straight or angle flow patterns Optional panel mount Handle options available Non-wetted
More informationASSEMBLY INSTRUCTIONS ACCORDING TO SAE J1453 FOR FLARED TUBES. 5. Clean properly with appropriate products the part of the tube to be flared.
ASSEMBLY INSTRUCTIONS ACCORDING TO SAE J1453 FOR FLARED TUBES 1. Before to start to flare the tube check for the correct parameters of all the tools to be used and substitute 2. Cut the tube at a 90 angle
More informationRebuild Instructions for 70001 and 70010 Transmission
Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before
More informationSTIHL Precision Series Hand Tools
STIHL Precision Series Hand Tools Spare Parts List A PH 80 Hedge Shear M PP 900/700 Pole Pruner Head Assembly B PL 0 Lopper N PP 900 Pole Pruner Head Parts C PL 0 Lopper O PS 0 Pruning Saw D PL 0 Lopper
More informationMACHINE SCREW ACTUATORS 2 to 100 Tons
2 to 100 Tons Top Plate 316 S.S. Must be bolted to lifting member to prevent rotation except when screw is keyed. Lifting Screw 316 S.S. Also available as threaded end or clevis end. Shell Cap 316 S.S.
More informationV47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
More informationShut-off & Lockout Valves 1/4" to 1-1/2" port size
Section 16 Shut-off & Lockout Valves 1/4" to 1-1/2" port size Contents T72 Excelon Shut-off & Lockout Valves 1/4", 3/8" Port Sizes....................................ALE-16-2 T73 Excelon Shut-Off & Lockout
More informationMP8000 Series Pneumatic Valve Actuators
14-1161- 9, Rev. A Technical Bulletin MP8000 Issue Date March 2016 MP8000 Series Pneumatic Valve Actuators Pre-Assembly Details Page 3 MP8000 Actuator Components 3 Tools Required to Assemble an MP8000
More informationCatalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI KSWA3... SW-3... Ball sert Type...9./2.... 42/6... 3 K2A... 3Z... Poppet sert Type...38/1... 3/... 4 CS41B... C4-3...
More informationSPECIFICATIONS FOR BOON EDAM TOMSED MODEL TUT-65TMB
SPECIFICATIONS FOR BOON EDAM TOMSED MODEL TUT-65TMB PRODUCT DESCRIPTION: BOON EDAM TOMSED MODEL TUT-65TMB STAINLESS STEEL BARCODE SCANNING ELECTRONIC REGISTERING TURNSTILE SCOPE OF OPERATION: A. The TUT-65TMB
More informationMÁQUINAS AGRÍCOLAS JACTO S.A. EDITION
AJ English version EDITION - 06/007 CODE - 9790 Parts catalog MÁQUINAS AGRÍCOLAS JACTO S.A. Rua Dr. Luiz Miranda, 650 7580-000 - Pompéia - SP - Brasil Tel.: +55 4 3405-00 - Fax: +55 4 345 306 E-mail: export@jacto.com.br
More informationRear Disc Kit. Front Caliper
Caliper and Wheel Kit 52-0600 1973-85 FX-FLH Chrome Rear Wheel/Brake Assembly includes chrome 16 x 3.0 Wheel Assembly, chrome caliper, chrome 51T sprocket with bolts, 10 or 11 1 /2 rear drill brake disc,
More informationSeries PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2662-CD/US Revised June, 212 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference
More informationScrew Thread Design. Rev. 3-4-09
Screw Thread Design Screw Thread Fundamentals A screw thread is defined as a ridge of uniform section in the form of a helix on either the external or internal surface of a cylinder. Internal threads refer
More informationChar-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors
Char-Lynn Spool Valve Hydraulic Motors Repair Information W Series Geroler Motors with Parking Brake 004 Nut Key Ring, Retaining Bearing Ring, Retaining Ring, Retaining Washer (Thick), Pressure Washer,
More informationTC 170 & TC 170 PD TRANSFER CASE
Automotive Corporation TC 170 & TC 170 PD TRANSFER CASE PARTS MANUAL Fabco Automotive Corporation, Livermore, CA Ph:(925) 454-9500 Fax:(925) 454-9501 1-(800) 967-8838 www.fabcoautomotive.com VII. PARTS
More informationFisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations
Instruction Manual 1061 F & G Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style F & G Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...
More informationThread and End Connection
www.swagelok.com and End Connection Identification Guide 2 Contents Introduction and End Connection Terminology.. 4 General Terminology... 5 Step-by-Step Identification Procedure for s and End Connections...
More informationService Manual Rol-Lift
R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing
More informationBETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS
BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS PART NUMBER: 132581 REVISION: A RELEASE DATE: 24 March 2000 Page 1 of 10
More informationMeritor Trailer Products
Meritor Trailer Products Contents LM & LC...5 TA & TC...37 TE...63 TM...77 Steering Axles...105 Flexair & Flexlite...119 Indair...171 SMT...181 AXL...193 3 4 Meritor Trailer Products Axle & Brake Parts
More informationBall Valves (HB Series) Catalog 4121-HB Revised, April 2005
Ball Valves (HB Series) Revised, April 2005 Introduction Parker High Pressure HB4 Series Ball Valves provide reliable shut-off or switching functions. The upper and lower trunnion bearings enhance the
More informationPneumatic Cylinders. Composite, round line repairable and disposable, and NFPA square interchangeable
Composite, round line repairable and disposable, and NFPA square interchangeable Table of Contents Series 01 Micro-Air Cylinders 1/2, 3/4, & 1-1/8 Bore Sizes...9 Application Information, Features, Capabilities...9
More informationCheck Valves Valve locator
Check Valves Valve locator Functional Symbol Flow Typical Model Cavity Rating Pressure Page Check valve, direct L/min (USgpm) bar (psi) FPR/4 Inline () 5 (5) - FPR/8 Inline (8) 5 (5) - FPR/ Inline 45 ()
More informationHAND PALLET TRUCK Lift-Rite
HAND PALLET TRUCK Lift-Rite Before you Order: To ensure that you get the correct parts, be certain whether your L-50 pallet truck is a standard model or one of the loweredheight models (MINI or CHEP).
More informationCheck Valves & Actuated Valves
heck Valves & ctuated Valves & U Series Piston non-return valves rated 6,000 psi & 10,000 psi X Series Piston non-return valves rated 20,000 psi Pneumatic ctuators Pneumatically actuated valves Electric
More informationScraper Passage Indicator. Electrical Indicator. Features
IV Scraper Passage Indicator Bulletin No: 5110.001.03 Date: June 2008 Cross Indexing No: n/a Supersedes: 5110.001.02 (1/06) Flag Indicator Electrical Indicator Options Description TDW s IV Scraper Passage
More informationANTENNA PARTS CATALOG
ANTENNA PARTS CATALOG Maco Antennas 302 S. East St. Mt. Carroll, IL 61053 www.macoantennas.net 815-244-3500 www.antennapartsoutlet.com SCREWS / BOLTS PART SIZE LENGTH DESCRIPTION PRICE S21 10-24 1/2" Machine
More informationMueller B-101 and A-3 Drilling and Tapping Machines
TM TM Mueller and Drilling and Tapping Machines A guide to selecting Mueller Equipment Mueller TM TM and Drilling and Tapping Machines When it comes to line stopping and drilling and tapping technology
More informationC O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S
C O N V E Y O R C O M P O N E N T S C H A I N S B E L T S B E A R I N G S January 2009 Issue 6 Valu Guide Brackets The Ultimate in Adjustability and Cost Savings Valu Guide brackets are part of a family
More informationManapak Sandwich Valves Series CM, CPOM, FM, PRDM, PRM, RM
Introduction Manapak valves provide a variety of check, flow control, pressure relief and pressure reducing functions in a compact NFPA D03, D05 and D08 sandwich style valve. The NFPA D03 valve body conforms
More informationSET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY
SET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY 82-13-1 O-Ring (Rear) The Lead Screw Assembly is shipped separately. Note: Install Electrical and Pneumatic Circuitry. Be Sure electrical and pneumatic
More information3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223
3 WAY (3/2) POPPET VALVES FOR AIR AND VACUUM SERVICE SOLENOID OR AIR ACTUATED BROCHURE N-223 HERION S HIGH PERFORMANCE POPPET VALVES For those applications requiring high Cv, fast response times, large
More informationSPRING BRAKES. service diaphram service housing service pushrod complete piggyback. Long Stroke Brake Chambers
49 Long Stroke Brake Chambers Watch your brake chambers! Most new vehicles are now being equipped with long-stroke brake chambers.this allows more stroke than older models. You will find clamp type 20
More informationChar-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997
Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47
More informationInnovative Products For Unique Applications. A Tradition of Excellence. Creative Engineering for Fluid Systems. Earthquake Proof Valves
A Tradition of Excellence With the development of the first rubber seated butterfly valve more than 70 years ago, the Henry Pratt Company became a trusted name in the flow control industry, setting the
More informationF-Series Camera Mounting Accessories
F-Series Camera Mounting Accessories Document Number: 427-0462-00-12 Version: 100 Issue Date: September 2010 2010. All rights reserved worldwide. FLIR Commercial Systems, Inc. 70 Castilian Drive Goleta,
More informationTemposonics. Magnetostrictive, Absolute, Non-contact Linear-Position Sensor Accessories
Temposonics Magnetostrictive, Absolute, Non-contact Linear-Position Sensor Accessories Includes Installation, Mounting and Application References Current Production and Retrofit Options for R-Series, G-Series
More informationFULL COLOR TAB #3 FM 25
FULL COLOR TAB #3 FM 25 FM - How to Order SERIES FM : Benefits Same construction as TA series with the added benefit of sleeve nut construction. Four tapped holes in Head and Cap-Standard. Optional four
More informationStainless Steel Cylinders DIN ISO 6431 and VDMA 24 562
Bores from 32 to 200 mm Double acting Standard executions Version Symbol TYPE MAGNETIC STANDARD AMX STAINLESS STEEL For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed
More informationSensors. Sensors. All Cylinders. Specifications. Features: Features Type REED HALL EFFECT NPN or PNP. Ø8mm - 125mm
Specifications Features Type REED HALL EFFECT NPN or PNP Applicable Series Configurations Construction Materials Body Mounting Bracket Cable Characteristics Operating Temperature Accuracy All Cylinders
More informationStainless Steel Single and Dual Circulation Kits
Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating
More informationHOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
More informationVe-Lock manufactures Needle Valves from Solid bar stock Materials & all parts details are as below:
Needle Valves : - Needle valves have a slender, tapered point at the end of the valve stem that is lowered through the seat to restrict or block flow. Fluid flowing through the Needle valve turns 90 degrees
More informationTrunnion-Design Ball Valves
Trunnion-Design Ball Valves 12" 20" (DN 300 500) Series 7150 12" (DN 300) Series 730S 12" 20" (DN 300 500) Series 7300 14" 24" (DN 350 600) Series 9150 14" 24" (DN 350 600) Series 9300 Installation, Maintenance
More informationMachine needle shut-off nozzle type HP
Machine needle shut-off nozzle type HP pneumatically or hydraulically controlled Index of contents Chapter Page Safety instructions... 2 Installation instructions... 3 - Installation steps... 3 Initial
More informationKF Needle & Gauge Valves
KF Needle & Gauge Valves Superior Fluid Control Products KF O-Ring & Packed Stem Style Needle Valves KF Needle Valves combine rugged construction, dependability and leak-free performance at high and low
More informationHOSE, TUBE, AND PIPE CLAMPS
hose, tube & clamp B/W pages 24/6/08 9:28 AM Page 2 HOSE, TUBE, AND PIPE CLAMPS TABLE OF CONTENTS Introduction 3 Construction 3 Application 3 Mounting 3 Standard Duty Clamps (HRL) Arrangements 4 Dimensions
More informationKA/8000/M, KA/8000, ISO cylinder (Stainless steel) Magnetic & Non-magnetic piston, double acting
K/8000/M, K/8000, ISO cylinder (Stainless steel) > > Ø 3... 00 mm > > High corrosion and acid resistance > > Ideal for applications in the food industry > > Conforms to DIN ISO 555, DIN ISO 63, VDM 56
More informationRotary actuators Rotary wing drives Series RAK. Brochure
Brochure 2 Rotary wing drives, angle of rotation: 30-270 Rotary wing drive, double-acting axis geometry: single 4 Rotary wing drives, angle of rotation: 90-270 Rotary wing drive, double-acting axis geometry:
More informationGAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES
GAS DISTRIBUTION PRODUCTS STEEL SERVICE TEES CONTINENTAL INDUSTRIES ABOUT US THE ULTIMATE CONNECTION Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and is today
More informationPUSH-PULL CABLES CONTROL SYSTEMS
ISO 9001 CERTIFIED PUSH-PULL CABLES CONTROL SYSTEMS WESCON PRODUCTS COMPANY A subsidiary of LATSHAW ENTERPRISES, INC. WESCON'S PUSH-PULL CONTROL SYSTEMS Push-Pull Cable Ends Wescon Push-Pull Cable Assemblies
More informationHT3 series Peck Feed Drills, with Equal Drill Time
Parts Manual Ersatzteil Liste PL92-280 HT3 series Peck Feed Drills, with Equal Drill Time HT3 SERIES PECK DRILL HT 3 C 005 S E 40 RPM Family Spindle B = 1/2-20 Male Thread, Jacobs Chuck C = 3/8-24 Female
More informationPneumatic actuators The Original! Technics of the top class.
Automatic valves Actuators Accessories Pneumatic actuators The Original! Technics of the top class. Leaflet no. S1-01e-13 Table of contents Advantages and your benefits...page 3 Figure: actuator...page
More information