Elastomeric Masonry, Stucco & Brick Paint
|
|
- Arron Kelly Green
- 1 years ago
- Views:
Transcription
1 Elastomeric Masonry, Stucco & Brick Paint For Exterior Use 100% Acrylic Latex Stretches up to 600% to Resist Cracking Formulated with a Mildewcide Low Sheen No. 68 White Properly prepared exterior vertical surfaces such as: Stucco, Masonry, Concrete, Concrete Block or Brick as well as adjacent Wood and Metal surfaces. Not for use on horizontal surfaces subject to foot traffic. Allow new stucco and masonry to cure for 30 days before painting. Remove all loose, peeling paint. Powerwash to remove chalk. Remove dirt and grease with BEHR NO. 990 CONCRETE & MASONRY CLEANER/ DEGREASER; remove mildew stains with BEHR NO. 62 PREMIUM MILDEW STAIN REMOVER. On galvanized metal, use a diluted solution of BEHR NO. 991 CONCRETE & MASONRY CLEANER/ETCHER to prepare surface. Follow all label instructions. Rinse thoroughly and allow a minimum of 24 hours to dry. Cracks and gaps wider than 1/16 (1.5 mm) should be routed open, dusted and patched with an elastomeric patching compound. Use an acrylic caulk around windows, doors and trim. Scuff sand glossy surfaces. Prime all uncoated, patched, chalky, wood and/or metal surfaces with BEHR NO. 436 EXTERIOR 100% ACRYLIC LATEX PRIMER & SEALER. ApplicationS DO NOT THIN. Intermix all cans of same product to ensure color uniformity. Stir paint before and occasionally during application. Use product when air and surface temperatures are between F (10-32 C). Do not use if rain or heavy dew is expected within 24 hours. Apply using a high quality 1 1/4 nap roller, nylon/polyester brush or airless sprayer ( spray tip). Spread rate is approximately sq. ft. (7-12 m 2 ) per gallon depending on type and porosity of surface. After 24 hours, a second coat must be applied at the same spread rate. A third coat may be required to achieve a final dry mil thickness of about mils. If airless spraying, use equipment with a minimum of 2500 PSI at the tip. Maintain a wet edge to avoid lap marks. Do not re-spread or re-work paint. Dries to the touch in 4-6 hours. Longer dry time required in cooler temperatures and higher humidity. Allow 24 hours between coats. After two weeks, cured paint film may be cleaned with a mild, non-abrasive liquid detergent. unused product from freezing. To recycle or properly dispose of paint in PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection. *LIMITED LIFETIME GUARANTEE BEHR PROCESS CORPORATION GUARANTEES THAT THIS PRODUCT WILL PROVIDE A WATERPROOF FINISH AND HIDE HAIRLINE CRACKS EXISTING AT TIME OF APPLICATION WHEN APPLIED AND CARED FOR ACCORDING TO LABEL DIRECTIONS. THIS GUARANTEE SHALL BE EFFECTIVE FOR SO LONG AS YOU RESIDE IN YOUR HOME AND IS MADE TO THE ORIGINAL RESIDENTIAL CONSUMER PAINT PURCHASER. THIS GUARANTEE IS NOT TRANSFERABLE. THIS GUARANTEE DOES NOT COVER WATER INTRUSION DUE TO STRUCTURAL DEFECTS OR CAULK FAILURE. Color fading and chalking will occur naturally over time. If this product fails to perform as specified, Behr Process Corporation will, at its option and upon proof-of-purchase, either furnish an equivalent amount of new paint to you, or refund the purchase price of this product. This guarantee excludes both (1) labor and costs of labor for the application or removal of any paint and (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This guarantee gives you specific legal rights and you may also have other rights, which vary from state to state.
2 Basement & Masonry Waterproofing Paint Mildew Resistant Film Smooth, Decorative Flat Finish Withstands 98 mph Wind-Driven Rain 100% Styrene Acrylic Sprayable! Saves Application Time No. 875 White Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks. New or Unpainted Surfaces: Test for loose, flaking concrete by pressing a piece of masking or If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. All holes or cracks must be properly patched with a fast setting hydraulic cement. Remove mildew stains with BEHR NO. 62 PREMIUM MILDEW STAIN All surfaces must be clean and free of dirt, dust, efflorescence and oil. Clean surface with BEHR NO. 991 CONCRETE & MASONRY CLEANER/ ETCHER. Follow all label instructions. Previously Painted Surfaces: BEHR NO. 875 BASEMENT & MASONRY WATERPROOFING PAINT provides best results when applied to bare or untreated surfaces. PREVIOUSLY PAINTED SURFACES IN GOOD, REPAINTABLE CONDITION MAY BE PAINTED WITH BEHR NO. 875, HOWEVER, BEHR WILL NOT GUARANTEE THE RESULTS. Test for loose, flaking paint by pressing a piece of masking or If the tape does not pull the paint from the surface, it can be painted. If the existing paint is removed, the loose paint should be removed down to a sound substrate by wire brushing or sanding. For Interior or Exterior application; remove deteriorated coating prior to application. Follow all label instructions. Follow all preparation instructions under New or Unpainted Surfaces above. *LIMITED WARRANTY BEHR Process Corporation warrants customer satisfaction with this product for 10 years on vertical surfaces from date of purchase, when applied to a properly prepared uncoated surface in accordance with the label directions. Previously painted or treated surfaces are excluded from this warranty. Color fading and chalking will occur naturally over time. If you are not satisfied with this product, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential product purchaser and is not transferable. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. V.O.C. (C.O.V.) <250 g/l REV. 2/08 Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50-90ºF (10-32ºC). Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. Apply using a high quality 1/2-3/4 nap roller, 4 nylon/polyester brush or an airliess 2,200-3,200 PSI using a spray tip. Apply at a spread rate of sq. ft. (7-9 m 2 ) per gallon on rough surfaces and sq. ft. (9-12 m 2 ) per gallon on smooth surfaces. Two coats minimum are required: First Coat: Using a brush or roller, work the waterproofer onto the masonry wall surface making certain to cover any pores or voids. Second Coat: Using a brush or roller, cover the entire surface. Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Re-apply product to these areas. DO NOT thin product or apply at a greater spread rate. Dries to touch in about one hour and can be recoated in four hours. Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 7 14 days.
3 Basement & Masonry Waterproofing Paint Mildew Resistant Film Smooth, Decorative Flat Finish Withstands 98 mph Wind-Driven Rain 100% Styrene Acrylic Sprayable! Saves Application Time No. 876 Basement Gray Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks. New or Unpainted Surfaces: Test for loose, flaking concrete by pressing a piece of masking or If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. All holes or cracks must be properly patched with a fast setting hydraulic cement. Remove mildew stains with BEHR NO. 62 PREMIUM MILDEW STAIN All surfaces must be clean and free of dirt, dust, efflorescence and oil. Clean surface with BEHR NO. 991 CONCRETE & MASONRY CLEANER/ ETCHER. Follow all label instructions. Previously Painted Surfaces: BEHR NO. 876 BASEMENT & MASONRY WATERPROOFING PAINT provides best results when applied to bare or untreated surfaces. PREVIOUSLY PAINTED SURFACES IN GOOD, REPAINTABLE CONDITION MAY BE PAINTED WITH BEHR NO. 876, HOWEVER, BEHR WILL NOT GUARANTEE THE RESULTS. Test for loose, flaking paint by pressing a piece of masking or If the tape does not pull the paint from the surface, it can be painted. If the existing paint is removed, the loose paint should be removed down to a sound substrate by wire brushing or sanding. For Interior or Exterior application; remove deteriorated coating prior to application. Follow all label instructions. Follow all preparation instructions under New or Unpainted Surfaces above. *LIMITED WARRANTY BEHR Process Corporation warrants customer satisfaction with this product for 10 years on vertical surfaces from date of purchase, when applied to a properly prepared uncoated surface in accordance with the label directions. Previously painted or treated surfaces are excluded from this warranty. Color fading and chalking will occur naturally over time. If you are not satisfied with this product, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential product purchaser and is not transferable. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. V.O.C. (C.O.V.) <250 g/l REV. 2/08 Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50-90ºF (10-32ºC). Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. Apply using a high quality 1/2-3/4 nap roller, 4 nylon/polyester brush or an airliess 2,200-3,200 PSI using a spray tip. Apply at a spread rate of sq. ft. (7-9 m 2 ) per gallon on rough surfaces and sq. ft. (9-12 m 2 ) per gallon on smooth surfaces. Two coats minimum are required: First Coat: Using a brush or roller, work the waterproofer onto the masonry wall surface making certain to cover any pores or voids. Second Coat: Using a brush or roller, cover the entire surface. Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Re-apply product to these areas. DO NOT thin product or apply at a greater spread rate. Dries to touch in about one hour and can be recoated in four hours. Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 7 14 days.
4 Concrete & Masonry Waterproofing Paint Mildew Resistant Film Smooth, Decorative Flat Finish Withstands 98 mph Wind-Driven Rain 100% Styrene Acrylic Sprayable! Saves Application Time No. 870 White Walls subject to hydrostatic pressure. Ideal for above or below grade Basement Walls, Retaining Walls, Garage Walls, Masonry Walls, Cinder Blocks, Stucco, Brick, Foundations and Landscape Walls. Apply to dry or slightly damp surfaces. Not for use on floors or walls with active water leaks. New or Unpainted Surfaces: Test for loose, flaking concrete by pressing a piece of masking or If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. All holes or cracks must be properly patched with a fast setting hydraulic cement. Remove mildew stains with BEHR NO. 62 PREMIUM MILDEW STAIN All surfaces must be clean and free of dirt, dust, efflorescence and oil. Clean surface with BEHR NO. 991 CONCRETE & MASONRY CLEANER/ ETCHER. Follow all label instructions. Previously Painted Surfaces: BEHR NO. 870 CONCRETE & MASONRY WATERPROOFING PAINT provides best results when applied to bare or untreated surfaces. PREVIOUSLY PAINTED SURFACES IN GOOD, REPAINTABLE CONDITION MAY BE PAINTED WITH BEHR NO. 870, HOWEVER, BEHR WILL NOT GUARANTEE THE RESULTS. Test for loose, flaking paint by pressing a piece of masking or If the tape does not pull the paint from the surface, it can be painted. If the existing paint is removed, the loose paint should be removed down to a sound substrate by wire brushing or sanding. For Interior or Exterior application; remove deteriorated coating prior to application. Follow all label instructions. Follow all preparation instructions under New or Unpainted Surfaces above. *LIMITED WARRANTY BEHR PROCESS CORPORATION warrants customer satisfaction with this product for 10 years on vertical surfaces from date of purchase, when applied to a properly prepared uncoated surface in accordance with the label directions. Previously painted or treated surfaces are excluded from this warranty. Color fading and chalking will occur naturally over time. If you are not satisfied with this product, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential product purchaser and is not transferable. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. V.O.C. (C.O.V.) <250 g/l REV. 2/08 Stir well before use. Do not thin product. Use with adequate ventilation. Use product when the surface and air temperature are between 50-90ºF (10-32ºC). Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. Apply using a high quality 1/2-3/4 nap roller, 4 nylon/polyester brush or an airliess 2,200-3,200 PSI using a spray tip. Apply at a spread rate of sq. ft. (7-9 m 2 ) per gallon on rough surfaces and sq. ft. (9-12 m 2 ) per gallon on smooth surfaces. Two coats minimum are required: First Coat: Using a brush or roller, work the waterproofer onto the masonry wall surface making certain to cover any pores or voids. Second Coat: Using a brush or roller, cover the entire surface. Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. Important: If leaking is still present after two coats, it indicates that voids or pinholes are still open. Re-apply product to these areas. DO NOT thin product or apply at a greater spread rate. Dries to touch in about one hour and can be recoated in four hours. Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 7 14 days.
5 Concrete & Masonary Waterproofer Interior/Exterior Silicone Enhanced To Keep Water Out For Brick, Concrete, Stucco & Tile Lasts Up to 10 Years No. 980 Natural Finish Horizontal and Vertical uncoated Concrete and Masonry surfaces such as: Concrete Block, Pavers, Stucco, Brick, Unglazed Tiles, Exposed Aggregate Concrete, Sandstone and Slate. Not recommended for use on areas subject to hydrostatic pressure such as basement walls or floors. CAUTION: Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. Remove old coating or sealer, if present, using BEHR N CONCRETE & MASONRY PAINT STRIPPER. Follow all label instructions. For proper penetration and adhesion, use BEHR NO. 991 CONCRETE & MASONRY CLEANER/ETCHER to clean and etch the surface. Follow all label instructions. TEST: Sprinkle a few drops of water onto the surface. If water is quickly absorbed, the surface is ready. If not absorbed, re-etch. Remove mildew stains with BEHR N0. 62 PREMIUM MILDEW STAIN DO NOT THIN. Stir or shake before applying. Use product when temperature is between F (10-32 C). Apply until saturated by brush, roller or garden sprayer to a dry surface at the spread rate of about 250 sq. ft. per gallon. Remove any puddles by spreading product to drier areas or by wiping up excess with a clean cloth. On vertical surfaces, apply from the bottom up and saturate well. Allow surface to dry hours, depending on temperature and humidity. Once dried, rough, vertical surfaces may be coated with an oil or latex-based paint or primer. Follow all label instructions. Do not paint horizontal surfaces after applying this product. Clean all equipment immediately with warm, soapy water. Properly dispose of all soiled rags and protect unused product from freezing. To recycle or properly dispose of paint in your community call CLEANUP (U.S.A. only) or visit lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at LEAD or log on to *LIMITED WARRANTY: BEHR PROCESS CORPORATION warrants customer satisfaction with this product for 10 years on vertical and horizontal surfaces from date of purchase, when applied to a properly prepared surface in accordance with the label directions. If you are not satisfied with this product, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential purchaser and is not transferable. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. WARNING! IRRITANT! HARMFUL IF SWALLOWED. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air and use a properly fitted respirator (NIOSH approved for organic vapor with P Series particulate prefilter). Obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap CAUTION: KEEP OUT OF REACH OF CHILDREN DO NOT TAKE INTERNALLY.
6 Wet-Look Sealer High-Gloss Clear Finish Excellent Topcoat Over Paints & Stains 100% Acrylic for Maximum Durability Interior/Exterior & Vertical/Horizontal No. 985 Hi-Gloss PRODUCT WILL APPEAR MILKY IN CONTAINER BUT WILL DRY TO A CLEAR FINISH. Use on Previously Coated or Uncoated, Vertical or Horizontal, Interior or Exterior surfaces such as: Pavers, Concrete, Mexican and Unglazed Tiles, Brick, Aggregate, Natural and Artificial Stone, Masonry and Stucco. Not recommended for use on wood, metal, granite, marble, terrazzo, travertine, areas immediately adjacent to pools or areas subject to hydrostatic pressure. Do not use over Oil-Based products. CAUTION: Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. Apply in sections so wet material does not have to be walked on during application. For proper penetration and adhesion of sealer on new or smooth concrete floors, use BEHR NO.991 CONCRETE & MASONRY CLEANER/ETCHER to clean and etch the surface. Follow all label instructions. Use BEHR NO. 990 CONCRETE & MASONRY CLEANER/DEGREASER to clean previously coated surface in sound condition. Scrape and remove any loose or peeling coating. To completely strip the surface use BEHR N CONCRETE & MASONRY PAINT STRIPPER. Follow all label instructions. Scrape and remove any loose or peeling coating. DO NOT THIN. Stir or shake before applying. Use product when temperature is between F (10-27 C). Do not apply in direct sunlight. Do not apply to wet surfaces or if rain or heavy dew is expected within 24 hours. Apply a thin coat using a nylon/polyester brush, 3/8-1/2 nap roller or a high quality pump sprayer with an adjustable tip at a spread rate of sq. ft. (14-28 m 2 ) per gallon. Spread rate is highly dependent on surface roughness and porosity. If sprayed, backroll for uniform thickness. Allow first coat to dry 4 hours, then apply a second coat at a spread rate of sq. ft. (28-37 m 2 ) per gallon. Additional coats (no more than 4) may be added for a higher gloss and added protection. Note: Horizontal surfaces may be subject to excessive wear. Therefore, periodic touch-ups may be necessary. LIMITED WARRANTY BEHR PROCESS CORPORATION warrants that this product meets BEHR S manufacturing specifications. If this product does not meet these specifications, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product to you or refund the purchase price of this product. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product; or (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Dries to touch in 1 hour. Longer dry time required in cooler temperatures and in higher humidity. Floors may be subjected to light foot traffic after 24 hours. Allow 72 hours before repositioning furniture or subjecting surface to heavy foot or automotive traffic. Park tires on corrugated cardboard for 14 days after applying product. Wait at least 30 days before cleaning with a mild, non-abrasive liquid detergent.
7 Low-Lustre Sealer Low-Gloss Clear Finish Excellent Topcoat Over Paints & Stains 100% Acrylic for Maximum Durability Interior/Exterior & Vertical/Horizontal No. 986 Low-Gloss PRODUCT WILL APPEAR MILKY IN CONTAINER BUT WILL DRY TO A CLEAR FINISH. Use on Previously Coated or Uncoated, Vertical or Horizontal, Interior or Exterior surfaces such as: Pavers, Concrete, Mexican and Unglazed Tiles, Brick, Aggregate, Natural and Artificial Stone, Masonry and Stucco. Not recommended for use on wood, metal, granite, marble, terrazzo, travertine, areas immediately adjacent to pools or areas subject to hydrostatic pressure. Do not use over Oil-Based products. CAUTION: Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. Apply in sections so wet material does not have to be walked on during application. For proper penetration and adhesion of sealer on new or smooth concrete floors, use BEHR NO.991 CONCRETE & MASONRY CLEANER/ETCHER to clean and etch the surface. Follow all label instructions. Use BEHR NO. 990 CONCRETE & MASONRY CLEANER/DEGREASER to clean previously coated surface in sound condition. Scrape and remove any loose or peeling coating. To completely strip the surface use BEHR N CONCRETE & MASONRY PAINT STRIPPER. Follow all label instructions. Scrape and remove any loose or peeling coating. DO NOT THIN. Stir or shake before applying. Use product when temperature is between F (10-27 C). Do not apply in direct sunlight. Do not apply to wet surfaces or if rain or heavy dew is expected within 24 hours. Apply a thin coat using a nylon/polyester brush, 3/8-1/2 nap roller or a high quality pump sprayer with an adjustable tip at a spread rate of sq. ft. (14-28 m 2 ) per gallon. Spread rate is highly dependent on surface roughness and porosity. If sprayed, backroll for uniform thickness. Allow first coat to dry 4 hours, then apply a second coat at a spread rate of sq. ft. (28-37 m 2 ) per gallon. Additional coats (no more than 4) may be added for a higher gloss and added protection. Note: Horizontal surfaces may be subject to excessive wear. Therefore, periodic touch-ups may be necessary. LIMITED WARRANTY BEHR PROCESS CORPORATION warrants that this product meets BEHR S manufacturing specifications. If this product does not meet these specifications, BEHR will, at its option and upon proof of purchase, either furnish an equivalent amount of new product to you or refund the purchase price of this product. BEHR will not be responsible for (1) labor or the cost of labor for removal or application of any product; or (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Dries to touch in 1 hour. Longer dry time required in cooler temperatures and in higher humidity. Floors may be subjected to light foot traffic after 24 hours. Allow 72 hours before repositioning furniture or subjecting surface to heavy foot or automotive traffic. Park tires on corrugated cardboard for 14 days after applying product. Wait at least 30 days before cleaning with a mild, non-abrasive liquid detergent. lead dust. LEAD IS TOXIC. Contact the National Lead Information Hotline at LEAD or log on to
Product Information/Specifications
BARN & FENCE PAINT NO. 25 BARN RED Smooth or rough sawn exterior vertical wood surfaces such as plywood, fences, shingles, shakes, siding. laminates, masonry and stucco surfaces. AVAILABLE IN: Gallon Only
T R A N S F E R A B L E F U L LY
HSTOPS A WALL OF WATER 22 FT. HIG! F U L LY T R A N S F E R A B L E RESISTS10 PSI ! 1 F U L LY T R A N S F E R A B L E HSTOPS A WALL OF WATER 22 FT. HIG RESISTS10 PSI Guaranteed To Stop Water Even Under
Product Information/Specifications
DECK WASH No. 61 Ideal for the Maintenance Cleaning of Exterior Wood, Vinyl or Composite Decks, Porches, Fences & Siding. AVAILABLE IN: Quart Only No. 61 Clear No. 61 32 oz. NOT TINTABLE 500-600 sq. ft.
Walls Low sheen: They are cleaned more often but are susceptible to critical lighting.
Stage 3: Fixing/Pre-Paint Stage Information on Painting The First Coat of Paint is the Most Important Most project homes are specified with a 2 coat finish. Master Painters of Australia recommends 3 coats,
RESTORE 2X Solid Stain with Cool Touch Technology FAQs Page 1 of 11
Page 1 of 11 FEATURES & BENEFITS Q. What makes Restore 2X Solid Stain with Cool Touch Technology different from other solid stains? A. Restore 2X Solid Stain with Cool Touch Technology is unique from other
Spraytek Acrylic FAQ s
Spraytek Acrylic FAQ s Question: What is the Concrete Coatings, Inc. SprayTek System? Answer: Concrete Coatings Incorporated Spray Tek Acrylic System is a combination of a modified acrylic resin and specially
Guide to Waterproofing Solutions. for interior and exterior use
Guide to Waterproofing Solutions for interior and exterior use Excessive moisture in basements and foundation walls can cause significant problems including structural decay, high humidity levels and mold
INFUSION REACTIVE. Helping you protect, restore and beautify your concrete
INFUSION REACTIVE STAIN systems guide Helping you protect, restore and beautify your concrete Create UNique DESIGNS NEVER TO BE DUPLICATED H&C *VOC INFORMATION H&C INFUSION Reactive Concrete Stain, Water
Prior to beginning work, Contractor shall furnish to Owner the following:
DIVISION 8 PAINTING SPECIFICATIONS 8.1 General 8.1.1 Scope Contractor shall provide all labor, material, and equipment and perform all operations necessary for all painting work specified including the
Aspect Metal Peel & Stick Tile Installation Guide
Aspect Metal Peel & Stick Tile Installation Guide Proper surface preparation is essential for a successful project Failure to follow recommended surface preparation instructions may void the warranty Read
Installation manual for Authentic Stone Veneer
Installation manual for Authentic Stone Veneer Please read carefully before installing: Install all Authentic Stone Veneer in accordance with ACI 530.1/ASCE 6/TMS 602 Specifications for Masonry Structures.
Premium quality tools are important; not only will high quality rollers, brushes, and products create a better result, they ll make your job easier.
How to Paint your Pool Introduction Painting is one of the best ways to protect and beautify your pool. In addition to adding a vibrant, fresh color, a new coat of paint can be a cost- efficient way to
ARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials
ARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials SECTION 03 92 50 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
Finishing SITE Finishing Instructions Painting Tips Aluminum Astragal Painting Doorlite Frame Finishing... 2.
Finishing... 2.3 Painting Tips... 2.12 Aluminum Astragal Painting... 2.15 Doorlite Frame Finishing... 2.17 SITE 2 2014 2.1 2.2 2014 SITE 2 SITE 2 2014 2.3 2.4 2014 SITE 2 SITE 2 2014 2.5 Painting Tips
K2 STONE NATURAL VENEER
INTRODUCTION WHAT IS K2 NATURAL THINSTONE VENEER? Natural K2 Stone veneer is real stone, cut 1 inch thick, making it light enough to be installed as a veneer. Sometimes referred to as thin veneer, thin
Acrylic Enamel Topcoat
Acrylic Enamel Topcoat ACRYL-GLO TECHNICAL DATA SHEET The ACRYL-GLO single-stage acrylic enamel paint system provides a durable finish that is easy to apply and suitable for both commercial and passenger
SECTION EXTERIOR PAINTING
SECTION 09911 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
Application of Exterior Wood Finishes
Application of Exterior Wood Finishes The following information is excerpted from the publication, Exterior Wood in the South Selection, Applications, and Finishes by Daniel L. Cassens and William C. Feist;
LIFETM. "14" Series High Solids Epoxy Concrete Sealer. Product Specifications
LIFETM Product Specifications "14" Series High Solids Epoxy Concrete Sealer Description: A premium quality 2-part water base epoxy concrete sealer that provides epoxy toughness, chemical resistance and
High-pressure (3000 p.s.i.) power washer with turbo tip. Condensation test material: Several one-foot square transparent pieces of plastic Duct tape
Application Guide Type EP Epoxy Overview Supplies Needed Ramuc Type EP Epoxy offers a hard, tough, durable finish, providing stain, chemical, and abrasion resistance for protection of concrete, plaster,
Alumigrip 4200 Application Process Instruction
Application Procedure Characteristics Product Information is a 3-component high solid durable polyurethane topcoat that provides premium gloss and distinctness of image (DOI) designed to meet and exceed
SECTION EXTERIOR PAINTING
New Football Stadium 09.91.13-1 PART 1 GENERAL 1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints. SECTION 09.91.13 EXTERIOR PAINTING C. Scope: Finish exterior surfaces exposed
Epoxy/Urethane Concrete Coating System
Epoxy/Urethane Concrete Coating System Application Guide Endura offers a coating system for concrete floors consisting of an epoxy primer and a urethane topcoat. It can be used on garage, warehouse and
ONBOARD MAINTENANCE PAINT GUIDE
ONBOARD MAINTENANCE PAINT GUIDE CONTENT Page A practical Onboard Maintenance Paint Guide 1.0 2.0 3.0 INSPECTION AND PLANNING 4 HSE 6 SURFACE PREPARATION 8 The purpose of this guide is to provide easy and
VC 104+ Rigid Grade / Rigid Grade Imagine VC 104 Rigid Grade Commercial Customised
Page 1 of 6 instructions VC 104+ Rigid Grade / VC 104+ Rigid Grade Imagine / (for the rest of this document referred to as VC 104) can be applied to new and used trucks and trailers with painted rigid
09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS
09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS PDS SE-160 01-2006 1. PRODUCT NAME SE-160 Clear Surface Coating (water-based copolymer) Specialty Elastomeric Topcoat 2. MANUFACTURER
Columbia flooring will resist fading from exposure to sunlight or artificial light.
LIMITED LIFETIME WARRANTY AND MAINTENANCE FOR RESIDENTIAL USE Columbia is so confident in the design and durability of our Columbia flooring products and accessories, that we back them with a Limited Lifetime
Minor Cracks in Horizontal Surfaces
Cracks, chips and broken or flaking areas in concrete are not only unsightly, they can lead to further deterioration of the surface. The result is a costly replacement project as opposed to a simple repair.
How to Stain Wood-Grain Textured Fiberglass Doors
How to Stain Wood-Grain Textured Fiberglass Doors Factory finished door units do not require additional field finishing. See maintenance steps for proper care. Requirements Find a well-lit staining location
1. Concrete. 2. Steel. 3. Galvanized metal. 4. Aluminum (not anodized or otherwise coated). 5. Wood. 6. Gypsum board.
SECTION 099123 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
TECHNICAL DATA SHEET HAMMERITE METAL PAINT. Smooth Hammered Satin Aerosol
TECHNICAL DATA SHEET HAMMERITE METAL PAINT Smooth Hammered Satin Aerosol TENDER ITEM NO (Where applicable) Hammerite Products Ltd. ICI Paints, Wexham Road Slough, Berkshire, SL2 5DS. Telephone (01753)
General Surface Preparation
General Surface Preparation Proper surface preparation will contribute significantly to the longevity of Ace Paint products. Follow these general guidelines for best results. CLEAN: Paint will not adhere
PAINTING OF CLARIFIER
1 PAINTING OF CLARIFIER PART 1 GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required for the surface preparation and application of shop painting systems on ferrous
BUILT-UP ROOF COATING SMOOTH and GRANULE SURFACE SPECIFICATION
07560 BUR BUILT-UP ROOF COATING SMOOTH and GRANULE SURFACE SPECIFICATION PART 1: GENERAL 1.01 SCOPE: To extend the useful service life of the aged or new asphalt built-up roof system and to reduce cooling
Application Instructions for Keystone Kool Deck on Existing Concrete
Application Instructions for Keystone Kool Deck on Existing Concrete REQUIRED MATERIALS Keystone Kool Deck PTA Bonding Agent Water 20 Mesh Marble Sand White Portland Cement OPTIONAL TOOLS Mortex Ad-Tex
Tractor Painting Tips
Keeping your tractor or equipment well kept & free from rust & corrosion will extend the life of your investment & help retain its value for a longer period of time. It can be difficult, in many cases,
Contract drawings, Division 0, Conditions of the Contract, and Division1, General Requirements, apply to the Work of this Section
SECTION 09900 - PAINTING Contract drawings, Division 0, Conditions of the Contract, and Division1, General Requirements, apply to the Work of this Section PART 1 - GENERAL 1.1 SUMMARY A. Provide materials,
Technical Data. wedi Liquid Vapor Barrier AEA-VBC-500
Technical Data wedi Liquid Vapor Barrier AEA-VBC-500 Technical Data wedi Liquid Vapor Barrier AEA-VBC 500 Overview wedi Liquid Vapor Barrier AEA-VBC-500 is for wedi applications in residential and commercial
SECTION PAINTS and COATINGS MASTER ARCHITECTURAL PAINTING SPECIFICATION
SECTION 09 90 00 PAINTS and COATINGS MASTER ARCHITECTURAL PAINTING SPECIFICATION December 2, 2014 Behr Process Corporation 3400 W. Segerstrom Avenue, Santa Ana, California 92704 (714) 545-7101 SECTION
Successful Painting Jobs Start Here.
Successful Painting Jobs Start Here. The Right Primer Makes All the Difference. Selecting the right primer for the job is a critical part of improving paint coverage and achieving the highest quality finish
STUCCO PATCHING AND REPAIR. B. Stucco Crack Repair
STUCCO PATCHING AND REPAIR Existing system: 2-coat stucco system with a polymer-based system finish coat. The base system is a product similar to a LaHabra Fastwall 100 with an El Rey Stucco PermaFlex
BENTLEY ELEMENTS COLLECTION LVT
This document refers to the following products: Product Size Installation direction Seams treatment Elements Tiles See specifications 90 None Elements Planks See specifications Stair Step None Note: This
bout your HOUSE before you start Repairing And Replacing Materials Exterior Walls
A bout your HOUSE before you start Repairing And Replacing Materials Exterior Walls CE 28 h Exterior finish materials are expected to protect the house from the elements while providing an attractive appearance.
Dow Corning AllGuard Silicone Elastomeric Coating. Application and Maintenance Guide
Dow Corning AllGuard Silicone Elastomeric Coating Application and Maintenance Guide Contents This document is intended to provide installation and field testing instructions for Dow Corning AllGuard Silicone
RESTORE 10X Advanced Resurfacer FAQs Page 1 of 11
Page 1 of 11 FEATURES & BENEFITS Q. Is the new Restore 10X Advanced Resurfacer replacing the first generation of Restore 10X? A. Yes, the new Restore 10X Advanced Resurfacer will replace the first generation
CROWN PAINTING SCHEDULE
CROWN PAINTING SCHEDULE ALL PAINTS AVAILABLE THROUGH SHERWIN-WILLIAMS PAINT STORES. PLEASE GO TO sherwinwilliams.com store locator to find the store closest to you. These paints are mainly commercial/industrial
RockSolid Deck Restoration Application
RockSolid Deck Restoration Application Read all instructions carefully before starting installation. For further details, application techniques and possible installation updates see our website at www.rocksolidfloors.com/support.
DIY. made. easy! Don t just DO IT YOURSELF DO IT WITH BEAUMONTS!
DIY PREPARE & CLEAN AN OUTDOOR AREA FOR TILING Natural stone is generally thicker and heavier than porcelain or ceramic tiles, so there are a couple of important points to note about the surface that the
SECTION 12. Surface Retarders. Sec 12 TECHNICAL DATA SHEET. Surface Retarders. Face-Off... 12-3 Top Cast... 12-5. American Owned American Made
SECTION PRODUCT PAGE Face-Off... -3 Top Cast... -5 American Owned American Made -1 Face-Off Surface Protectant PRODUCT DESCRIPTION Face-Off is an innovative surface protectant designed to keep splatter,
Resurfacing Concrete. Page 1 of 5
Resurfacing Concrete Materials List QUIKRETE Concrete Resurfacer (No. 1131) (see calculator on page 5 for quantity needed) QUIKRETE Concrete and Stucco Wash (No. 8601) QUIKRETE Concrete Sealer (No. 8800)
PAINT. PAINTING WALLS... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP... 118
PAINT PAINTING WALLS...... 115 -Interior Walls -Exterior Walls PAINTING DOORS... 117 CLEAN UP....... 118 112 Basic Construction Safety SAFETY TALK #1: Drink plenty of water and watch for dehydration! When
Window and Door Care and Maintenance
Window and Door Care and Maintenance 1. Installation 2. Paint/Stain 3. Hardware/Operation/Adjustment 4. Initial Cleaning 5. Ongoing Maintenance 6. Avoid 7. Problems/Trouble-Shooting 1. Installation: Your
SECTION 03 35 43 POLISHED CONCRETE FINISHING
SECTION 03 35 43 POLISHED CONCRETE FINISHING PART 1 - GENERAL 1.01 SUMMARY A. Provide polished concrete finishing system where indicated on drawings, complete. This section includes the following: 1. Concrete
Exterior Timber Decks. Please note: The life span of coatings on decks is very limited and will require regular maintenance of the coating
1/5 pages Systems 3 coats Cetol HLSe or 1 coat Cetol HLSe and 2 Coats Cetol Deck or 1 coat Cetol HLSe and 2 Coats Cetol Deck plus Please select required system. Key Practical coverage in m²/ltr per coat,
Brick, Stone & Block Panel Maintenance, Cleaning, Repair & Replacement Guidelines. guidelines. Read these maintenance,
Brick, Stone & Block Panel Maintenance, Cleaning, Repair & Replacement Guidelines Read these maintenance, cleaning & replacement guidelines completely and thoroughly before beginning. These instructions
P R O D U C T A D V I C E S H E E T
P R O D U C T A D V I C E S H E E T E S T A T E E G G S H E L L All Farrow & Ball paints are eco friendly with low or minimal VOC (Volatile Organic Compounds) content and are water based giving them a
preparing, finishing and maintaining timber garden decking
NEW range for 2009 Your simple guide to preparing, finishing and maintaining timber garden decking Manufacturer of quality decking finishes You can bring out the natural beauty of your timber garden decking
BONCOTE CEMENT PAINT. Product Specification. Product Name: PRODUCT DESCRIPTION: SUGGESTED APPLICATIONS: LOCATION: ENVIRONMENTAL INFORMATION:
Product Specification Product Name: BONCOTE CEMENT PAINT PRODUCT DESCRIPTION: APAS* Target level for this product: 70g/L. is a Portland cement based product supplied in a powder form and coloured with
METAL ROOF RESTORATION SAMPLE DESIGN GUIDELINES
METAL ROOF RESTORATION SAMPLE DESIGN GUIDELINES REFLECTICLEAN ACRYLIC/URETHANE Elastomeric Roofing Systems, Inc 6900 Bleck Dr. Rockford, MN 55373 800.403.7747 -or- 763.565.6900 fax: 763.565.6901 email:
RAPTOR TRUCK BED LINER - BLACK
4 x 750ml RAPTOR base coating x L RAPTOR hardener TECHNICAL DATA SHEET & U-POL s RAPTOR Truck Bed Liner is a durable K polyurethane coating that provides surfaces with a protective barrier. RAPTOR Tintable
Roppe Vinyl Stair Treads
Maintenance 7.1.1 Required Initial Maintenance DO NOT scrub or mop the stair treads for at least 72 hours after the installation is completed to allow the adhesive, Quik-Stik Adhesive Tape and ROPECC Epoxy
A. Work on this project shall consist of, but is not limited to, the following:
PART 1 - GENERAL CLEANING AND RESTORATION OF SECTION 05900-1 1.1 SUMMARY A. Work on this project shall consist of, but is not limited to, the following: 1. Clean and treat all exposed anodized architectural
Instructions For Use
Instructions For Use Concrobium Mold Control dries on surfaces to create an invisible antimicrobial shield that kills and prevents mold, and gets rid of musty odours. The breakthrough, Health Canada approved
SKIMSTONE APPLICATION INSTRUCTIONS FOR CONCRETE FLOORS
SKIMSTONE APPLICATION INSTRUCTIONS FOR CONCRETE FLOORS Note: Label and Brochure Instructions are abbreviated. Read and follow all directions in this instruction booklet before using product. Rudd Company,
Making Professional Coating Results A Reality
Game-Changing Application System Making Professional Coating Results A Reality Hillyard Concrete Defense changes the way coatings are applied - delivering professional results without the cost of professional
MILESTONE APPLICATION INSTRUCTIONS FOR INTERIOR VERTICAL SURFACES
MILESTONE APPLICATION INSTRUCTIONS FOR INTERIOR VERTICAL SURFACES Note: Label and Brochure Instructions are abbreviated. Read and follow all directions in this instruction booklet before using this product.
4. Preparatory Work. preparatory work 4.1 PLANNING 4.2 SURFACE PREPARATION
4. Preparatory Work 4.1 PLANNING Quality control starts with good planning and management. An Inspection and Test Plan, ITP (refer to Appendix D) which lists down the project s inspection and testing requirements
Acrylic Walls Installation Instructions
Acrylic Walls Installation Instructions IMPORTANT Please read carefully the following instructions before installing your shower acrylic walls. If you have any questions on this shower acrylic walls installation
Epoxy Floor Coating Problem Solving Guide
Table of Contents: Page: Troubleshooting Issue: 2. Color Differential 3. Fish Eye 4. Milky or Cloudy Coatings 5. Orange Peel 6. Peeling or Delamination 8. Delamination between Coats 9. Pinholes/Bubbling
Extreme Sealing Tape
Extreme Sealing Tape Technical Data May, 2013 Product Description 3M Extreme Sealing Tape is a family of single coated, pressure sensitive adhesive tapes designed for difficult sealing applications. The
DuPont ChromaOne Acrylic Urethane Single Stage
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaOne is a productive acrylic urethane designed for spot, panel and overall repairs of OEM Single Stage finishes, both solids and
HARDSCAPE CLEANING Hardscape Cleaning with EaCo Chem, Inc.
HARDSCAPE CLEANING Hardscape Cleaning with EaCo Chem, Inc. SAFE - COST EFFECTIVE - EXCELLENT CLEANING RESULTS EaCo Chem, Inc. 765 Commerce Avenue New Castle, PA 16101 (800) 313-8505 Fax (724) 656-0757
Installation Instructions
Please read all instructions before installing wall panels. Always plan before you place! 1. Before installation: a. Acclimate Stain Steel Panels, Trim, adhesives and wall substrates to room temperature
PORTER S WALLPAPER. Product Specification. Product Name: PRODUCT DESCRIPTION: SUGGESTED APPLICATIONS: COLOURS AND CUSTOM COLOURS: LOCATION:
Product Specification Product Name: PORTER S WALLPAPER PRODUCT DESCRIPTION: Porter s has collaborated with local designers to create beautiful works that translate into stunning wallpaper. We have produced
Document Library TS Data Sheet 46012 46013 46014
Document Library TS Data Sheet 46012 46013 46014 Rev:2 Effective: 01/11/2002 3M Marine High Strength Repair Filler Data Sheet Status: Active 3M Part No.(s) 46012 46013 46014 3M Part Descriptor(s) Pint
Wood Door Finishing Guidelines
WARRANTY INFORMATION: SPECIAL PAINTING REQUIREMENTS: The warranty for this product shall be void if the Product sections are not painted or sealed in accordance with DASMA TDS 162 (available at www.dasma.com)
SCHWARTZ WATER-BASE WOOD FLOOR SEALER AND WATER-BASE PREMIIUM WOOD FLOOR FINISH
!! SCHWARTZ WATER-BASE WOOD FLOOR SEALER AND WATER-BASE PREMIIUM WOOD FLOOR FINISH A Complete Guide for Preparation, Application, Curing and Maintenance for use with Schwartz H 2 O Water-base Floor Finish
Shower Walls and Tub Surrounds
Reverso en español TEC Skill Set How-To Project Guide Shower Walls and Tub Surrounds 3 Steps to a Beautiful Tile Surface! 1. Prepare the surface 2. Set the tile 3. Grout and caulk H.B. Fuller Construction
Backstop NT. Backstop NT Application Instructions DS181. A High Performance, Polymer-Based, Noncementitious Water-Resistive Membrane and Air Barrier
Backstop NT A High Performance, Polymer-Based, Noncementitious Water-Resistive Membrane and Air Barrier Backstop NT Application Instructions CHECKLIST PRIOR TO THE INSTALLATION OF BACKSTOP NT TEXTURE,
Most commonly Liquid Tub Liners are used for restoration of bathtubs.
Most commonly Liquid Tub Liners are used for restoration of bathtubs. Due to that, the provided below detailed instruction is for restoration of the bath tubs. Quite the same way can be used for restoration
Low Maintenance No Polish Options
Low Maintenance No Polish Options Low Maintenance Option: No Buff No Polish Products: LINO (Sheet, Tile), LVT, HET (excludes Possibilities, Corlon and Abode ) 2. Remove any dried adhesive residue with
PRISM Low VOC Single Stage Color Flat (76), Satin (77), Semi-Gloss (78), & Gloss (79)
PRISM Low VOC Single Stage Color Flat (76), Satin (77), Semi-Gloss (78), & Gloss (79) Product Data Sheet PRODUCT DESCRIPTION Prism Low VOC Single Stage Color is a two-component urethane coating. This premium
HOUSING QUALITY STANDARDS (HQS)
HOUSING QUALITY STANDARDS (HQS) Series 3 LEAD-BASED PAINT AND INSPECTIONS 3.1LBP Rev. 5-5-06 Finding of Lead-Based Paint 3.2LBP Defective paint found in units built before 1978 where children under six
PPG HI-TEMP 1027 PRODUCT DATA SHEET. June 30, 2014 Revision of January 28, 2014 DESCRIPTION
DESCRIPTION One component, high-build heat-resistant inert multipolymeric matrix coating to prevent corrosion under insulation (CUI) of carbon and stainless steel to temperatures ranging up to 650 C (1200
Acrylic Coatings: The Perfect Stucco Finish
Acrylic Coatings: The Perfect Stucco Finish By Larry Miller and Joe Miller Whether a stucco surface is new or old, there are many different finish coatings in today s marketplace that are supposedly right
SECTION PAINTING AND COATING
SECTION 09 9000 PART 1 GENERAL 1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints, stains, varnishes, and other coatings. C. Scope: Finish all interior and exterior surfaces exposed
JOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING. Test Code: 2060 Version: 01
JOB READY ASSESSMENT BLUEPRINT PAINTING AND DECORATING Test Code: 2060 Version: 01 Specific Competencies and Skills Tested in this Assessment: Wood Finishes Identify thinning products Identify wood finish
Match Patch Pro FC CONCRETE FLOOR REPAIR. Technical Data. Description:
CONCRETE FLOOR REPAIR Technical Data SECTION 03 3543 BONDED ABRAISIVE POLISHING CONCRETE FLOORS Download Specification SECTION 09 9723 CONCRETE SEALERS Match Patch Pro FC Patent Pending Description: FC
Selection and Use of Coatings, Water Repellents, and Sealants to Control Moisture Intrusion in Above-Ground Concrete and Masonry Walls
Selection and Use of Coatings, Water Repellents, and Sealants to Control Moisture Intrusion in Above-Ground Concrete and Masonry Walls Kenneth A. Trimber KTA-Tator, Inc. Coating, Water Repellent, Sealant
GUIDE SPECIFICATION COMBINATION SURFACE SYSTEM FOR NEW HOT MIX ASPHALT TENNIS COURTS I. PART 1 - GENERAL
COMBINATION SURFACE SYSTEM FOR NEW HOT MIX ASPHALT TENNIS COURTS I. PART 1 - GENERAL 1.1 SUMMARY A. This section is a part of the entire set of Contract Documents and shall be coordinated with the applicable
RedGard Crack Prevention and Waterproofing Membrane
1 Product Name 2 Manufacturer Custom Building Products 13001 Seal Beach Blvd. Seal Beach, CA 90740-2757 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax: 800-200-7765 Email: contactus@cbpmail.net
REGISTER OF APPROVED ENCAPSULANT PRODUCTS PAGE 1
Commonwealth of Massachusetts -Department of Public Health Childhood Lead Poisoning Prevention Program Donovan Health Building, 1st floor Randolph St. Canton Ma 02021 REGISTER OF APPROVED ENCAPSULANT PRODUCTS
How to repair your existing low slope flat roof.
How to repair your existing low slope flat roof. Recycled Rubber Roofing is not a "Roof Coating." It is a liquid emulsion used as the underlayment of a new or retrofit, built-up roofing system. One of
Painting. The Challenges of. Kitchens and Baths
The Challenges of Painting Kitchens and Baths BY BRIAN DOHERTY For paint to stand up to these hard-working rooms, the surfaces must be clean, and the finishes must be durable Repainting can change the
TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
RESIDENTIAL HARDWOOD WARRANTIES
RESIDENTIAL HARDWOOD WARRANTIES Limited Warranties for Prefinished Solid and Engineered Hardwood Floors Manufacturing Defects Century Flooring* ("Century") hereby warrants to the original buyer ("Buyer"),
SEE HOW TO MAKE LIME PLASTER WHY USE LIME? PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013
SEE HOW TO MAKE LIME PLASTER PATTI STOUTER, BUILD SIMPLE INC. FEBRUARY 2013 WHY USE LIME? Lime plaster forms a light, clean, and durable surface that is resistant to weather and mold. A thin layer attaches
VORTEX Waterborne Basecoat Intermix Color Series VX
VORTEX Waterborne Basecoat Intermix Color Series VX PRODUCT DATA SHEET PRODUCT DESCRIPTION Waterborne Basecoat is an easy-to-apply, fast-drying basecoat that provides excellent color matches to today s
Section Painting and Finishes (General)
Section 099100 Painting and Finishes (General) PART 1 - GENERAL 1.01 Conditions A. The general provisions of the Contract, including General Conditions and Special Provisions apply to the work specified
ASPHALT CEMENTS & COATINGS. Protective Asphalt Coatings Asphalt Primers Aluminum Coatings
ASPHALT CEMENTS & COATINGS Roof Mastics Protective Asphalt Coatings Asphalt Primers Aluminum Coatings ROOF MASTICS #211 Plastic Cement Mule-Hide #211 Plastic Cement is a general purpose formulation for