Catalyst 6500 Series DFC Memory Installation Note

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Catalyst 6500 Series DFC Memory Installation Note"

Transcription

1 Catalyst 6500 Series DFC Memory Installation Note Product numbers: MEM-DFC-128M=, MEM-DFC-256M=, MEM-DFC-512M= (for WS-F6K-DFC) MEM-XCEF M= (for WS-F6K-DFC3A, WS-F6700-DFC3A, WS-F6700-DFC3B) MEM-XCEF720-1GB= (for WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL) This publication provides procedures for installing memory on the following Catalyst 6500 series Distributed Forwarding Cards (DFCs): WS-F6K-DFC WS-F6K-DFC3A WS-F6700-DFC3A WS-F6700-DFC3B WS-F6700-DFC3BXL Note For the WS-F6700-DFC3A, WS-F6700-DFC3B, and WS-F6700-DFC3BXL, the memory module is located on the base WS-X67xx module, under the DFC3 daughtercard. You must remove the daughtercard from the module to upgrade the memory. Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA USA Copyright Cisco Systems, Inc. All rights reserved.

2 Contents Contents This publication contains these sections: Safety Overview, page 2 Required Tools, page 3 Installation Guidelines, page 3 Verifying the DFC Memory, page 4 Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only), page 5 Removing the SODIMM, page 9 Installing the SODIMM, page 13 Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only), page 14 Related Documentation, page 18 Obtaining Documentation, page 19 Documentation Feedback, page 19 Obtaining Technical Assistance, page 20 Obtaining Additional Publications and Information, page 21 Safety Overview Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement. Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement

3 Required Tools Required Tools These tools are required to upgrade the memory on the Catalyst 6500 series DFC: 3/16-inch flat-blade screwdriver for the captive installation screws on the module on which the DFC is installed WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL only Number 1 Phillips-head screwdriver for the screws and cap nuts that fasten the DFC3 to the WS-X67xx module Antistatic mat or antistatic foam Your own ESD-prevention equipment or the disposable grounding wrist strap included with all upgrade kits, field-replaceable units (FRUs), and spares Always use an ESD wrist strap when handling modules or coming into contact with internal components. Installation Guidelines Observe the following cautions when upgrading the memory on a DFC: Always use an ESD wrist strap when handling modules or coming into contact with internal components. During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. SODIMMs are sensitive components that are susceptible to ESD damage. To prevent ESD damage, handle SODIMMs by the edges only; avoid touching the memory modules, pins, or traces (the metal fingers along the connector edge of the SODIMM). When inserting SODIMMs, use firm but not excessive pressure. If you damage a socket, you will have to return the DFC to the factory for repair. Use care not to damage the connectors on the module. If you damage a connector, it will be necessary to return the module to Cisco for repair. You must install screws in all available standoffs. The screws provide grounding between the DFC3 and the module. Failure to install all screws will invalidate the safety approvals and pose a risk of fire and electrical hazard. 3

4 Verifying the DFC Memory Verifying the DFC Memory Table 1 lists the default memory configurations and available upgrades. Table 1 Memory Configurations DFC version Default Memory Upgradeable Memory Part Number WS-F6K-DFC3 128 MB 256 MB 512 MB WS-F6K-DFC3A 512 MB No upgrade available WS-F6700-DFC3A 256 MB 512 MB 1 GB WS-F6700-DFC3B 256 MB 512 MB 1 GB WS-F6700-DFC3BXL 1 GB No upgrade available MEM-DFC-256M= MEM-DFC-512M= MEM-XCEF M= MEM-XCEF720-1GB= MEM-XCEF M= MEM-XCEF720-1GB= To verify the memory configuration on the DFC, enter the remote command module mod show memory summary command, where mod is the module with an installed DFC. Add the processor and I/O totals to get the total memory for the DFC. This example shows how to check the total memory on the DFC on a fabric-enabled module in slot 9: Router# remote command module 9 show memory summary Router-dfc9# Head Total(b) Used(b) Free(b) Lowest(b) Largest(b) Processor 31C5BFC I/O E <output truncated> Router# The above example shows the total memory on the DFC is 256 MB. 4

5 Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) For the WS-F6700-DFC3A, WS-F6700-DFC3B, and WS-F6700-DFC3BXL, the memory module is located on the base WS-X67xx module, under the DFC3. To upgrade the DFC3 memory, you must first remove the DFC3 from the module. To remove a DFC3, follow these steps: Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when servicing. Statement 1034 During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Step 1 Step 2 Remove the module from the Catalyst 6500 series switch. (Refer to the Catalyst 6500 Series Module Installation Guide for removal instructions.) Place the module on an antistatic mat or foam, with the front of the module facing toward you. Step 3 Use a Phillips-head screwdriver to remove the securing screws and the two cap nuts. (See Figure 1.) 5

6 Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Figure 1 Removing the Securing Screws and Cap Nuts WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 4 Partially install the cap nut, as shown in Figure 2, about 3 turns so that there is a space of about 1/8 inch (3.175 mm) between the bottom of the cap nut and the top of the DFC3. The cap nut acts as a stop when you unseat the connector so that the DFC3 does not move horizontally and cause damage to the module. 6

7 Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Figure 2 Partially Installing the Cap Nut Cap nut Appx 1/8 inch Step 5 With your left hand, lift slightly at the location shown in Figure 3. While lifting with your left hand, rock the DFC3 up and down with your right hand, no more than half an inch in either direction, to unseat the DFC3 from the module. 7

8 Removing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Figure 3 Unseat the DFC3 from the Module Lift here Rock up and down WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 6 Remove the cap nut. Step 7 Hold the DFC3 with both hands, and gently lift the DFC3 straight up from the module. (See Figure 4.) 8

9 Removing the SODIMM Figure 4 Removing the DFC3 from the Module WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 8 Place the removed DFC3 on an antistatic mat or antistatic foam pad. Step 9 Proceed to the Removing the SODIMM section on page 9. Removing the SODIMM During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. To remove the existing SODIMM, follow these steps: Step 1 Step 2 Step 3 Step 4 Make sure that you take the necessary precautions to prevent ESD damage. Remove the module with the DFC or DFC3A from the system. (Refer to the Catalyst 6500 Series Module Installation Guide for removal instructions.) Place the module on an antistatic mat or pad. Locate the SODIMM. (See Figure 5 for the WS-F6K-DFC, see Figure 6 for the WS-F6K-DFC3A, and see Figure 7 for the WS-X6700-DFC3A.) 9

10 Removing the SODIMM Figure 5 Location of SODIMM on a WS-F6K-DFC SDRAM SODIMM WS-X5530 STATUS Figure 6 Location of SODIMM on a WS-F6K-DFC3A S S WS-X5530 SS

11 Removing the SODIMM Figure 7 Location of SODIMM on a WS-X67xx Module for the DFC3A, DFC3B, and DFC3BXL DDR SDRAM SODIMM WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS

12 Removing the SODIMM Step 5 Release the spring clips from the SODIMM, and release the SODIMM from the socket. (See Figure 8.) Figure 8 Releasing the SODIMM Spring Clips Pull the tabs away with your thumbs, bracing your forefingers against the rails. The memory module will be released. Then raise the memory module to a vertical position. Memory module Step 6 When both ends of the SODIMM are released from the socket, grasp the ends of the SODIMM with your thumb and forefinger, and pull the SODIMM completely out of the socket. Step 7 SODIMMs are sensitive components that are susceptible to ESD damage. To prevent ESD damage, handle SODIMMs by the edges only; avoid touching the memory modules, pins, or traces (the metal fingers along the connector edge of the SODIMM). (See Figure 9.) Place the SODIMM in an antistatic container to protect it from ESD damage. This completes the SODIMM removal procedure. Proceed to the Installing the SODIMM section on page 13 to install the new SODIMM. 12

13 Installing the SODIMM Installing the SODIMM SODIMMs are sensitive components that are susceptible to ESD damage. To prevent ESD damage, handle SODIMMs by the edges only; avoid touching the memory modules, pins, or traces (the metal fingers along the connector edge of the SODIMM). (See Figure 9.) Figure 9 Handling a SODIMM Follow these steps to install the new SODIMM: Step 1 Step 2 Remove a new SODIMM from the antistatic container. Hold the SODIMM with the component side up and with the connector edge (the metal fingers) away from you. Step 3 Hold the sides of the SODIMM between your thumbs and forefingers. (See Figure 9.) Step 4 Tilt the SODIMM to approximately the same angle as the socket, and insert the connector edge into the socket. When inserting SODIMMs, use firm but not excessive pressure. If you damage a socket, you will have to return the DFC to the factory for repair. Step 5 Press the SODIMM down until it is secured by the spring clips. (See Figure 10.) Figure 10 Installing the SODIMM

14 Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Step 6 Step 7 When the SODIMM is installed, check the two alignment holes, and ensure that the spring retainer is visible. If it is not, the SODIMM is not seated properly. If any SODIMM appears misaligned, carefully remove it and reseat it in the socket. Push the SODIMM firmly back into the socket until the retainer springs snap into place. If you upgraded the memory on the WS-F6700-DFC3A, WS-F6700-DFC3B, or WS-F6700-DFC3BXL, you need to reinstall the DFC3. Proceed to the Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) section on page 14 to install the DFC3. Otherwise, reinstall the module. (Refer to the Catalyst 6500 Series Module Installation Guide for removal instructions.) Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) To install the DFC3 on a WS-X67xx module, follow these steps: During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Step 1 Align the mounting holes on the DFC3 (see Figure 11) with the male standoffs on the module. (See Figure 12.) Make sure that the remaining mounting holes on the DFC3 are aligned with the remaining standoffs. Figure 11 Mounting Holes on the DFC3 Align with the male standoffs on the module

15 Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Figure 12 Male Standoff Locations on the WS-X67xx Module Male standoffs WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 2 Ensure that the connectors on the DFC3 are aligned with the connectors on the module. Figure 13 shows the connectors on the underside of the DFC3. Figure 13 DFC3A Connectors Connectors

16 Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Step 3 Apply pressure to the area shown in Figure 14 to seat the power connector. Figure 14 Seating the Power Connector Apply pressure WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 4 Use care not to damage the connectors on the module. If you damage a connector, it will be necessary to return the module to Cisco for repair. Apply pressure to the location shown in Figure 15 to fully seat the DFC3 on the module. 16

17 Installing the DFC3 (WS-F6700-DFC3A, WS-F6700-DFC3B, WS-F6700-DFC3BXL Only) Figure 15 Seating the DFC3 on the Module Apply pressure WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 5 Use a Phillips-head screwdriver to install the securing screws and the two cap nuts. (See Figure 16.) You must install screws in all available standoffs. The screws provide grounding between the DFC3 and the module. Failure to install all screws will invalidate the safety approvals and pose a risk of fire and electrical hazard. Note You should visually verify that there are standoffs beneath the mounting holes before installing the securing screws. 17

18 Related Documentation Figure 16 Installing the Securing Screws and Cap Nuts WS-X5530 WS-X6724-SFP 24PORT GIGABIT ETHERNET - SFP STATUS Step 6 Install the module in the Catalyst 6500 series switch. (Refer to the Catalyst 6500 Series Module Installation Guide for installation instructions.) Related Documentation These documents are available for the Catalyst 6500 series switches: Regulatory Compliance and Safety Information for the Catalyst 6500 Series Switches Catalyst 6500 Series Switch Installation Guide Catalyst 6500 Series Switch Module Installation Guide Catalyst 6500 Series Switch Software Configuration Guide Catalyst 6500 Series Switch Command Reference Catalyst 6500 Series Switch Cisco IOS Software Configuration Guide Catalyst 6500 Series Switch Cisco IOS Command Reference Catalyst 6500 Series DFC/DFC3A Installation Note Catalyst 6500 Series DFC3A, DFC3B, and DFC3BXL Installation Note 18

19 Obtaining Documentation Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: You can access the Cisco website at this URL: You can access international Cisco websites at this URL: Ordering Documentation You can find instructions for ordering documentation at this URL: You can order Cisco documentation in these ways: Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at or, elsewhere in North America, by calling NETS (6387). Documentation Feedback You can send comments about technical documentation to You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address: Cisco Systems Attn: Customer Document Ordering 170 West Tasman Drive San Jose, CA We appreciate your comments. 19

20 Obtaining Technical Assistance Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller. Cisco Technical Support Website The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year at this URL: Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL: Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool automatically provides recommended solutions. If your issue is not resolved using the recommended resources, your service request will be assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL: For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly. To open a service request by telephone, use one of the following numbers: Asia-Pacific: (Australia: ) EMEA: USA: For a complete list of Cisco TAC contacts, go to this URL: Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1) Your network is down, or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation. 20

21 Obtaining Additional Publications and Information Severity 2 (S2) Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation. Severity 3 (S3) Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels. Severity 4 (S4) You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations. Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL: Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL: iq Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iq Magazine at this URL: Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: World-class networking training is available from Cisco. You can view current offerings at this URL: 21

22 Obtaining Additional Publications and Information This document is to be used in conjunction with the documents listed in the Related Documentation section. CCSP, the Cisco Square Bridge logo, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iquick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iq Expertise, the iq logo, iq Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0406R) Copyright Cisco Systems, Inc. All rights reserved. 22

Release Notes for Catalyst 6500 Series and Cisco 7600 Series Router MSFC2A ROMMON Software

Release Notes for Catalyst 6500 Series and Cisco 7600 Series Router MSFC2A ROMMON Software Release Notes for Catalyst 6500 Series and Cisco 7600 Series Router MSFC2A ROMMON Software Current Release:12.2(17r)S6 October 28, 2005 This publication describes how to upgrade the ROMMON on your Catalyst

More information

Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Router Supervisor Engine 720 ROMMON

Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Router Supervisor Engine 720 ROMMON Release Notes for Catalyst 6500 Series Switch and Cisco 7600 Series Router Supervisor Engine 720 ROMMON Current Release: 84(2) May 16, 2005 Past Releases: 81(3), 77(1) This publication describes how to

More information

Installing and Configuring External Flash Memory Cards in Cisco 3600 Series Routers

Installing and Configuring External Flash Memory Cards in Cisco 3600 Series Routers Installing and Configuring External Flash Memory Cards in Cisco 3600 Series Routers Product Numbers: MEM3600-4FC=, MEM3600-8FC=, MEM3600-16FC=, MEM3600-20FC= This document describes how to install external

More information

Cisco OC-3/OC-12/OC-48 SFP Transceiver Modules Compatibility Matrix

Cisco OC-3/OC-12/OC-48 SFP Transceiver Modules Compatibility Matrix Cisco OC-3/OC-12/OC-48 SFP Transceiver Modules Compatibility Matrix This publication contains information about the Cisco platforms and software versions that support the OC-3/OC-12/OC-48 Small Form-Factor

More information

Cisco Network Planning Solution 2.0.2 Documentation Guide and Supplemental License Agreement

Cisco Network Planning Solution 2.0.2 Documentation Guide and Supplemental License Agreement Cisco Network Planning Solution 2.0.2 Documentation Guide and Supplemental License Agreement June 2007 This documentation guide contains the End User Supplemental License Agreement for Cisco Systems Network

More information

Including License and Warranty

Including License and Warranty Phone Guide Cisco IP Phone 7914 Expansion Module Including License and Warranty 1 Introducing the Cisco IP Phone 7914 Expansion Module 2 Installing the 7914 Expansion Module 3 Features of the 7914 Expansion

More information

FXO, FXS, and E&M Voice Interface Card Support on Cisco 1700 Series Routers

FXO, FXS, and E&M Voice Interface Card Support on Cisco 1700 Series Routers FXO, FXS, and E&M Voice Interface Card Support on Cisco 1700 Series Routers This document describes the support on the Cisco 1751 and Cisco 1760 routers for the following new voice interface cards (VICs):

More information

Cisco Aironet 5.5-dBi Omnidirectional Antenna (AIR-ANT2455V-N)

Cisco Aironet 5.5-dBi Omnidirectional Antenna (AIR-ANT2455V-N) Cisco Aironet 5.5-dBi Omnidirectional Antenna (AIR-ANT2455V-N) This document describes the Cisco Aironet AIR-ANT2455V-N 5.5-dBi Omnidirectional Antenna and provides instructions for mounting it. The antenna

More information

Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix

Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix This publication contains information about the Cisco platforms and software versions that support the 10-Gigabit Ethernet transceiver

More information

Cisco IP Phone 7961G/7961G-GE and 7941G/7941G-GE Enhancements

Cisco IP Phone 7961G/7961G-GE and 7941G/7941G-GE Enhancements Enhancements The purpose of this document is to provide a summary of some of the feature behavior enhancements on the new, and how they differ from the Cisco IP Phone 7960G/7940G. Complete information

More information

DHCP Release and Renew CLI in EXEC Mode

DHCP Release and Renew CLI in EXEC Mode DHCP Release and Renew CLI in EXEC Mode The DHCP Release and Renew CLI in EXEC Mode feature provides the ability to perform two independent operations from the command-line interface (CLI): Immediately

More information

Cisco IP Phone 7912G. At a Glance

Cisco IP Phone 7912G. At a Glance At a Glance Cisco IP Phone 7912G 1 Overview 2 Connecting Your Phone 3 Introducing Your Cisco IP Phone 7912G 4 Tips for Using Your Phone 5 Using Additional Features 6 Where to Find More Information 7 Safety

More information

Connecting Cisco Fast Ethernet ISDN PRI Network Modules to the Network

Connecting Cisco Fast Ethernet ISDN PRI Network Modules to the Network Connecting Cisco Fast Ethernet ISDN PRI Network Modules to the Network Revised: May 1, 2008, OL-12808-01 This guide describes how to connect Cisco Fast Ethernet Integrated Services Digital Network (ISDN)

More information

Upgrading to the Cisco ubr7246vxr Universal Broadband Router

Upgrading to the Cisco ubr7246vxr Universal Broadband Router Upgrading to the Cisco ubr7246vxr Universal Broadband Router This document outlines the process for upgrading an existing Cisco ubr7246 universal broadband router to a Cisco ubr7246vxr chassis, along with

More information

Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix

Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix Cisco 10-Gigabit Ethernet Transceiver Modules Compatibility Matrix This publication contains information about the Cisco platforms and software versions that support the 10-Gigabit Ethernet transceiver

More information

Cisco Router and Security Device Manager File Management

Cisco Router and Security Device Manager File Management Application Note Cisco Router and Security Device Manager File Management Introduction Cisco Router and Security Device Manager (SDM) allows you to view and manage the file system on your Cisco router

More information

Cisco Aironet 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N)

Cisco Aironet 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) Cisco Aironet 5-dBi Omnidirectional Antenna (AIR-ANT2450V-N) This document describes the Cisco Aironet AIR-ANT2450V-N 5-dBi Omnidirectional Antenna and provides instructions for mounting it. The antenna

More information

Overview: Cisco Wireless Network Management Suite 1.0

Overview: Cisco Wireless Network Management Suite 1.0 Overview: Cisco Wireless Network Management Suite 1.0 Introduction Cisco Wireless Network Management Suite 1.0 (CWNMS 1.0) is a client/server based network management application suite for Broadband Fixed

More information

Cisco IP Phone 7960 and 7940 Series. At a Glance

Cisco IP Phone 7960 and 7940 Series. At a Glance At a Glance Cisco IP Phone 7960 and 7940 Series 1 Overview 2 Connecting Your Cisco IP Phone 3 Introducing Your Cisco IP Phone 4 Tips for Using Your Phone 5 How to Get Help with Keys and Features 6 Where

More information

Quick Start Guide: Cisco Wireless Control System for Linux

Quick Start Guide: Cisco Wireless Control System for Linux Quick Start Guide: Cisco Wireless Control System for Linux Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS

More information

Cisco IP Phone 7914 Expansion Module

Cisco IP Phone 7914 Expansion Module Quick Start Guide Cisco IP Phone 7914 Expansion Module 1 Introduction to the Cisco IP Phone 7914 Expansion Module 2 Installing the 7914 Expansion Module 3 Features 4 How to Use the 7914 Expansion Module

More information

Disaster Recovery System Administration Guide for Cisco Unified Presence Server Release 1.0(3)

Disaster Recovery System Administration Guide for Cisco Unified Presence Server Release 1.0(3) Disaster Recovery System Administration Guide for Cisco Unified Presence Server Release 1.0(3) The Disaster Recovery System Administration Guide provides an overview of the Disaster Recovery System, describes

More information

Cisco CWDM GBIC and CWDM SFP Installation Note

Cisco CWDM GBIC and CWDM SFP Installation Note Cisco CWDM GBIC and CWDM SFP Installation Note, Product Numbers: CWDM-GBIC-1470= CWDM-GBIC-1550= CWDM-SFP-1470= CWDM-SFP-1550= CWDM-GBIC-1490= CWDM-GBIC-1570= CWDM-SFP-1490= CWDM-SFP-1570= CWDM-GBIC-1510=

More information

Cisco Smart Services for Small and Medium Business: Solutions for Your Success

Cisco Smart Services for Small and Medium Business: Solutions for Your Success Cisco Smart Services for Small and Medium Business: Solutions for Your Success Realize the Full Potential of Your Network Cisco Smart Services for Small and Medium Business help you realize the full potential

More information

Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix

Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix Cisco 100-Megabit Ethernet SFP Modules Compatibility Matrix This document contains information about the Cisco platforms and software versions that support the 100-Megabit Ethernet Small Form-Factor Pluggable

More information

Cisco Aironet Power over Ethernet Application Note

Cisco Aironet Power over Ethernet Application Note Cisco Aironet Power over Ethernet Application Introduction The goals of this document include the following: Identify Cisco inline-powered WLAN devices and their usage requirements with a Cisco inline-powered

More information

Constraining IP Multicast in a Switched Ethernet Network

Constraining IP Multicast in a Switched Ethernet Network Constraining IP Multicast in a Switched Ethernet Network This module describes how to configure routers to use the Cisco Group Management Protocol (CGMP) in switched Ethernet networks to control multicast

More information

Smart Care Guide to Troubleshooting Appliance Registration

Smart Care Guide to Troubleshooting Appliance Registration Smart Care Guide to Troubleshooting Appliance Registration Revised: September 2008 Contents Troubleshooting Appliance Registration Verify the registration of the Partner CCO account Verify that the Customer

More information

CISCO IOS SOFTWARE FEATURE PACKS FOR THE CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES (MODULAR) INTEGRATED SERVICES ROUTERS

CISCO IOS SOFTWARE FEATURE PACKS FOR THE CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES (MODULAR) INTEGRATED SERVICES ROUTERS CISCO IOS SOFTWARE FEATURE PACKS FOR THE CISCO 1700 SERIES MODULAR ACCESS ROUTERS AND CISCO 1800 SERIES (MODULAR) INTEGRATED SERVICES ROUTERS This product bulletin provides details on the Cisco IOS s for

More information

Advanced Integration Module Installation in Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

Advanced Integration Module Installation in Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers Quick Start Guide Advanced Integration Module Installation in Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers 1 Required Tools and Equipment 2 Opening the Chassis 3 Installing AIMs

More information

How to Register, Start, and Access a Cisco Online Exam

How to Register, Start, and Access a Cisco Online Exam How to Register, Start, and Access a Cisco Online Exam Lifecycle Services and SMB Exams The process for registering and taking a Cisco online exam is different from the process for registering and taking

More information

VPN Device Manager Client for Cisco IOS Software (XSM Configuration)

VPN Device Manager Client for Cisco IOS Software (XSM Configuration) VPN Device Manager Client for Cisco IOS Software (XSM Configuration) Note For the primary documentaiton of the latest version of the VPN Device Manager (version 1.2), see the Installation Guide and Release

More information

L2TP Dial-Out Load Balancing and Redundancy

L2TP Dial-Out Load Balancing and Redundancy L2TP Dial-Out Load Balancing and Redundancy The L2TP Dial-Out Load Balancing and Redundancy feature enables an L2TP network server (LNS) to dial out to multiple L2TP access concentrators (LACs) When the

More information

CISCO SMALL AND MEDIUM BUSINESS CLASS VOICE SOLUTIONS: CISCO CALLMANAGER EXPRESS BUNDLES

CISCO SMALL AND MEDIUM BUSINESS CLASS VOICE SOLUTIONS: CISCO CALLMANAGER EXPRESS BUNDLES OVERVIEW CISCO SMALL AND MEDIUM BUSINESS CLASS VOICE SOLUTIONS: CISCO CALLMANAGER EXPRESS BUNDLES COMPANY PROFILE Cisco CallManager Express (CME) promotional bundles are appropriate for small businesses

More information

Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note

Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note Product Number: WS-6509-NEB-UPGRD= This publication describes how to upgrade your Catalyst 6509-NEB switch or Cisco OSR-7609 Router to use

More information

Cisco Unified Wireless IP Phone 7925G Accessory Guide

Cisco Unified Wireless IP Phone 7925G Accessory Guide Cisco Unified Wireless IP Phone 7925G Accessory Guide This guide describes the accessories that you can order for your Cisco Unified Wireless IP Phone 7925G. Contents This document contains these sections:

More information

CISCO CATALYST 3750 SERIES SWITCHES

CISCO CATALYST 3750 SERIES SWITCHES AT-A-GLANCE CISCO CATALYST 3750 SERIES SWITCHES Product Part Number Port Speed Number Cisco Catalyst 3750-24TS 3750-24TS 3750-24FS 3750-24PS 3750-24PS 3750-48TS 3750-48TS 3750-48PS WS-C3750-24TS-S 10/100

More information

Danish Train Operator Gets Customer Service Back On Track

Danish Train Operator Gets Customer Service Back On Track Danish Train Operator Gets Customer Service Back On Track Danish Rail uses Cisco Unified Communications to sharpen its customer focus and revitalise its call centre operation EXECUTIVE SUMMARY Customer

More information

Data Center Infrastructure Design Guide 2.1 Readme File

Data Center Infrastructure Design Guide 2.1 Readme File Data Center Infrastructure Design Guide 2.1 Readme File Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS

More information

Release Notes for the Cisco WAN Modeling Tools, Release 15.4.00 Patch 1

Release Notes for the Cisco WAN Modeling Tools, Release 15.4.00 Patch 1 Release Notes for the Cisco WAN Modeling Tools, Release 15.4.00 Patch 1 June 2007 Rev. A0 These release notes are for use with the Cisco WAN Modeling Tools, which includes the following subsystems: NMT

More information

Cisco Unified Wireless IP Phone 7925G Accessory Guide

Cisco Unified Wireless IP Phone 7925G Accessory Guide Cisco Unified Wireless IP Phone 7925G Accessory Guide This guide describes the accessories that you can order for your Cisco Unified Wireless IP Phone 7925G. Contents This document contains these sections:

More information

White Paper: Active Directory Capacity Planning (Cisco Unity Versions 4.x, 3.1, and 3.0(3) and Later with Microsoft Exchange)

White Paper: Active Directory Capacity Planning (Cisco Unity Versions 4.x, 3.1, and 3.0(3) and Later with Microsoft Exchange) White Paper: Active Directory Capacity Planning (Cisco Unity Versions 4.x, 3.1, and 3.0(3) and Later with Microsoft Exchange) Revised August 10, 2007 Purpose This document provides capacity planning recommendations

More information

CISCO SFP OPTICS FOR PACKET-OVER-SONET/SDH AND ATM APPLICATIONS

CISCO SFP OPTICS FOR PACKET-OVER-SONET/SDH AND ATM APPLICATIONS DATA SHEET CISCO SFP OPTICS FOR PACKET-OVER-SONET/SDH AND ATM APPLICATIONS The Cisco industry-standard Small Form-Factor Pluggable Interface Converter (SFP) for packet-over-sonet/sdh (POS), optical networking,

More information

CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES

CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES DATA SHEET CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES Offering a single ISDN BRI S/T interface, this WIC may require an external Network Termination 1 (NT1),

More information

Cisco Registered Envelope Recipient Guide

Cisco Registered Envelope Recipient Guide September 8, 2008 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number:

More information

Building Your Network Foundation: Routing and Switching Made Simple

Building Your Network Foundation: Routing and Switching Made Simple Building Your Network Foundation: Routing and Switching Made Simple Whatever the size of your organization, a business-class network is within your reach. By understanding and taking some simple steps,

More information

CD Installation Guide for the Cisco SIP Proxy Server on Linux

CD Installation Guide for the Cisco SIP Proxy Server on Linux CD Installation Guide for the Cisco SIP Proxy Server on Linux The describes how to install the Cisco SIP Proxy Server software on a Pentium-based server running Linux Kernel 2.2.13 or later. Network engineers,

More information

CISCO AIRONET POWER INJECTOR

CISCO AIRONET POWER INJECTOR DATA SHEET CISCO AIRONET POWER INJECTOR Cisco Aironet Power Injector products increase the deployment flexibility of Cisco Aironet wireless access points and bridges by providing an alternative powering

More information

Figure 1. The Cisco Aironet Power Injectors Provide Inline Power to Cisco Aironet Access Points and Bridges

Figure 1. The Cisco Aironet Power Injectors Provide Inline Power to Cisco Aironet Access Points and Bridges DATA SHEET CISCO AIRONET POWER INJECTOR Cisco Aironet Power Injector products increase the deployment flexibility of Cisco Aironet wireless access points and bridges by providing an alternative powering

More information

Cisco Aironet 1130AG Series

Cisco Aironet 1130AG Series Ordering Guide Cisco Aironet 1130AG Series The Cisco Aironet 1130AG Series IEEE 802.11a/b/g Access Point is a fixed-configuration, dual-band access point. Built in to the access point are two radios each

More information

Cisco Unified Web and Interaction Manager Browser Settings Guide

Cisco Unified Web and  Interaction Manager Browser Settings Guide Cisco Unified Web and E-Mail Interaction Manager Browser Settings Guide For Unified Contact Center Enterprise Release 9.0(2) September 2014 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive

More information

CISCO CATALYST 6500 SUPERVISOR ENGINE 32

CISCO CATALYST 6500 SUPERVISOR ENGINE 32 PRODUCT BULLETIN NO. 2678 CISCO CATALYST 6500 SUPERVISOR ENGINE 32 Cisco Systems introduces the Cisco Catalyst 6500 Series Supervisor Engine 32, the next generation of supervisor engine for the Cisco Catalyst

More information

Cisco Multiband Diversity Omnidirectional Ceiling-Mount Antenna (AIR-ANTM4050V-R)

Cisco Multiband Diversity Omnidirectional Ceiling-Mount Antenna (AIR-ANTM4050V-R) Cisco Multiband Diversity Omnidirectional Ceiling-Mount Antenna (AIR-ANTM4050V-R) This document outlines the specifications and describes the AIR-ANTM4050V-R multiband diversity omnidirectional ceiling-mount

More information

Times AA-9303 or equivalent (plenum rated)

Times AA-9303 or equivalent (plenum rated) Cisco Aironet 6.5-dBi Diversity Patch Antenna (AIR-ANT2465P-R) This document outlines the specifications, describes the AIR-ANT2465P-R 6-dBi patch antenna, and provides instructions for mounting it. The

More information

Transferring Files Using HTTP or HTTPS

Transferring Files Using HTTP or HTTPS Transferring Files Using HTTP or HTTPS First Published: May 5, 2005 Last Updated: May 14, 2009 Cisco IOS Release 12.4 provides the ability to transfer files between your Cisco IOS software-based device

More information

NETWORK AVAILABILITY IMPROVEMENT SUPPORT OPERATIONAL RISK MANAGEMENT ANALYSIS

NETWORK AVAILABILITY IMPROVEMENT SUPPORT OPERATIONAL RISK MANAGEMENT ANALYSIS DATA SHEET NETWORK AVAILABILITY IMPROVEMENT SUPPORT OPERATIONAL RISK MANAGEMENT ANALYSIS Operational Risk Management Analysis helps you maintain and improve network availability by evaluating the risks

More information

CISCO 10GBASE X2 MODULES

CISCO 10GBASE X2 MODULES DATA SHEET CISCO 10GBASE X2 MODULES Figure 1. Cisco 10GBASE X2 and Xenpak Module PRODUCT OVERVIEW The Cisco 10GBASE X2 modules (Figure 1) offers customers a wide variety of 10 Gigabit Ethernet connectivity

More information

Cisco IronPort Encryption Appliance 6.5.5 Release Notes

Cisco IronPort Encryption Appliance 6.5.5 Release Notes Cisco IronPort Encryption Appliance 6.5.5 Release Notes Published: August 30, 2011 Contents These release notes contain important information about running the latest version of the IronPort Encryption

More information

Terminal Services Overview

Terminal Services Overview Terminal Services Overview This chapter provides an overview of Cisco IOS terminal services and includes the following main sections: Cisco IOS Network Access Devices Line Characteristics and s Asynchronous

More information

CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND 12.4T FEATURE SETS FOR THE CISCO 3800 SERIES ROUTERS

CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND 12.4T FEATURE SETS FOR THE CISCO 3800 SERIES ROUTERS PRODUCT BULLETIN NO. 2877 CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND FEATURE SETS FOR THE CISCO 3800 SERIES ROUTERS This product bulletin details changes to the Cisco IOS Software packaging for Cisco

More information

CISCO IP PHONE EXPANSION MODULE 7914

CISCO IP PHONE EXPANSION MODULE 7914 DATA SHEET CISCO IP PHONE EXPANSION MODULE 7914 Call coverage is a critical capability for administrative assistants and others who must monitor, manage, and cover the various status of calls. This requires

More information

This feature was introduced. This feature was integrated in Cisco IOS Release 12.2(11)T.

This feature was introduced. This feature was integrated in Cisco IOS Release 12.2(11)T. BGP Link Bandwidth The Border Gateway Protocol (BGP) Link Bandwidth feature is used to advertise the bandwidth of an autonomous system exit link as an extended community. This feature is configured for

More information

Cisco Unified Web and Interaction Manager System Requirements

Cisco Unified Web and  Interaction Manager System Requirements Cisco Unified Web and E-Mail Interaction Manager System F Unified Contact Center Express Release 4.2(1) July 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706

More information

Getting Started. Cisco Desktop Product Suite 4.5 (ICD)

Getting Started. Cisco Desktop Product Suite 4.5 (ICD) Getting Started Cisco Desktop Product Suite 4.5 (ICD) Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387)

More information

INCLUDING LICENSE AND WARRANTY

INCLUDING LICENSE AND WARRANTY Phone Guide Cisco IP Phone Expansion Module 7914 INCLUDING LICENSE AND WARRANTY 1 Introducing the Cisco IP Phone Expansion Module 7914 2 Installing the Expansion Module 7914 3 Features of the Expansion

More information

Cisco Aironet Dual Band MIMO Low Profile Ceiling Mount Antenna (AIR-ANT2451NV-R)

Cisco Aironet Dual Band MIMO Low Profile Ceiling Mount Antenna (AIR-ANT2451NV-R) Cisco Aironet Dual Band MIMO Low Profile Ceiling Mount Antenna (AIR-ANT2451NV-R) This document outlines the specifications for the AIR-ANT2451NV-R dual band MIMO low profile ceilng mount antenna and provides

More information

Cisco GLBP Load Balancing Options

Cisco GLBP Load Balancing Options Data Sheet Cisco GLBP Load Balancing Options Last updated: December 2005 INTRODUCTION The purpose of this document is to discuss the options that Cisco Gateway Load Balancing Protocol (GLBP) one of Cisco

More information

CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES

CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES DATA SHEET CISCO ISDN BRI S/T WIC FOR THE CISCO 1700, 1800, 2600, 2800, 3600, 3700, AND 3800 SERIES Offering a single ISDN BRI S/T interface, this WIC may require an external Network Termination 1 (NT1),

More information

Connecting Cisco Serial High-Speed WAN Interface Cards

Connecting Cisco Serial High-Speed WAN Interface Cards Connecting Cisco Serial High-Speed WAN Interface Cards Revised: April 5, 008, Overview This document describes Cisco serial and high-speed WAN interface cards (HWICs) and how to connect them to a network.

More information

CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND 12.4T FEATURE SETS FOR THE CISCO 2800 SERIES ROUTERS

CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND 12.4T FEATURE SETS FOR THE CISCO 2800 SERIES ROUTERS PRODUCT BULLETIN NO. 2879 CISCO IOS SOFTWARE RELEASES 12.4 MAINLINE AND FEATURE SETS FOR THE CISCO 2800 SERIES ROUTERS This product bulletin details changes to the Cisco IOS Software packaging for Cisco

More information

Cisco Unified CallConnector for Microsoft Office Troubleshooting Guide

Cisco Unified CallConnector for Microsoft Office Troubleshooting Guide Cisco Unified CallConnector for Microsoft Office Troubleshooting Guide First Published: April 2007 Last Updated: April 2007 OL 13005-01 In this document you will find basic information that will help you

More information

What every business needs to know about financing*

What every business needs to know about financing* What every business needs to know about financing* *without the small print Aligning your technology investments with changing business needs Financing is an acquisition strategy that can offer significant

More information

SURGE PROTECTION CABLES FOR SMART SERIAL INTERFACES

SURGE PROTECTION CABLES FOR SMART SERIAL INTERFACES DATA SHEET SURGE PROTECTION CABLES FOR SMART SERIAL INTERFACES Surge events, including ElectroStatic Discharge (ESD) and lightning surges, are common in many parts of the world, especially during electrical

More information

Enabling and Monitoring NetFlow on Subinterfaces

Enabling and Monitoring NetFlow on Subinterfaces Enabling and Monitoring NetFlow on Subinterfaces This module contains instructions for enabling and monitoring NetFlow on a router subinterface or a Versatile Interface Processor (VIP) controller interface.

More information

CISCO 100BASE-X SFP FOR FAST ETHERNET SFP PORTS

CISCO 100BASE-X SFP FOR FAST ETHERNET SFP PORTS DATA SHEET CISCO 100BASE-X SFP FOR FAST ETHERNET SFP PORTS PRODUCT OVERVIEW The Cisco 100BASE-X Small Form-factor Pluggable (SFP) is a hot-swappable input/output device that plugs into a Fast Ethernet

More information

Installing and Upgrading Memory and Packet Voice Data Modules

Installing and Upgrading Memory and Packet Voice Data Modules APPENDIX C Installing and Upgrading Memory and Packet Voice Data Modules This chapter describes how to install or upgrade memory or data modules in your router and contains the following sections: Safety

More information

White Paper: Cisco Unity Data and the Directory

White Paper: Cisco Unity Data and the Directory White Paper: Cisco Unity Data and the Directory Published February 28, 2002 This document describes the Cisco Unity data that is stored in the directory and explains how this data is kept consistent with

More information

CISCO CALLMANAGER EXPRESS 3.2

CISCO CALLMANAGER EXPRESS 3.2 ORDERING GUIDE CISCO CALLMANAGER EXPRESS 3.2 To be used by authorized partners and direct accounts only. HOW TO ORDER CISCO CALLMANAGER EXPRESS 3.2 Cisco CallManager Express (CME) is a feature in Cisco

More information

Getting Started with the Cisco IP Phone 7910 Series

Getting Started with the Cisco IP Phone 7910 Series Getting Started with the Cisco IP Phone 7910 Series Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387)

More information

CISCO MEETINGPLACE FOR OUTLOOK 5.3

CISCO MEETINGPLACE FOR OUTLOOK 5.3 DATA SHEET CISCO MEETINGPLACE FOR OUTLOOK 5.3 Rich-media Conferencing for Microsoft Outlook PRODUCT OVERVIEW Cisco MeetingPlace part of the Cisco IP Communications system is a complete rich-media conferencing

More information

END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR SELECTIVE CISCO CATALYST 6503, CATALYST 6506 AND CATALYST 6509 CHASSIS

END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR SELECTIVE CISCO CATALYST 6503, CATALYST 6506 AND CATALYST 6509 CHASSIS PRODUCT BULLETIN NO. 3037 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR SELECTIVE CISCO CATALYST 6503, CATALYST 6506 AND CATALYST 6509 CHASSIS Cisco Systems announces the end-of-sale and end-of-life dates

More information

Customizing Your Cisco Unified IP Phone on the Web

Customizing Your Cisco Unified IP Phone on the Web Phone Guide Customizing Your Cisco Unified IP Phone on the Web Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS

More information

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway

Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway Configuring Cisco Unified Communications Manager for the NovaTec TransNova S3 Voice Gateway This document describes how to configure Cisco Unified Communications Manager systems to use the NovaTec TransNova

More information

Voice-Over IP Monitoring Best Practices Deployment Guide for CAD 6.0/6.1

Voice-Over IP Monitoring Best Practices Deployment Guide for CAD 6.0/6.1 Voice-Over IP Monitoring Best Practices Deployment Guide for CAD 6.0/6.1 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000

More information

Cisco Router and Security Device Manager USB Storage

Cisco Router and Security Device Manager USB Storage Application Note Cisco Router and Security Device Manager USB Storage Introduction The USB Storage feature on the Cisco Router and Security Device Manager (Cisco SDM) allows the Cisco 871 and Cisco 1800,

More information

Cisco Router and Security Device Manager Cisco Easy VPN Remote

Cisco Router and Security Device Manager Cisco Easy VPN Remote Application Note Cisco Router and Security Device Manager Cisco Easy VPN Remote Introduction This document explains how to configure a Cisco Easy VPN Remote. Cisco Easy VPN Introduction Cisco Easy VPN

More information

7906G, 7911G, 7931G, 7941G, 7942G, 7945G, 7961G, 7961GE, 7962G, 7965G, 7970G, 7971G, 7971GE,

7906G, 7911G, 7931G, 7941G, 7942G, 7945G, 7961G, 7961GE, 7962G, 7965G, 7970G, 7971G, 7971GE, FIPS 140-2 Non-Proprietary Security Policy for the Cisco Unified IP Phone 7906G, 7911G, 7931G, 7941G, 7942G, 7945G, 7961G, 7961GE, 7962G, 7965G, 7970G, 7971G, 7971GE, and 7975G Introduction This is a non-proprietary

More information

New Cisco Catalyst 3750 Series Switches Overview

New Cisco Catalyst 3750 Series Switches Overview Product Bulletin No. 2119 New Cisco Catalyst 3750 Series Switches Overview Cisco Systems is pleased to introduce the new Cisco Catalyst 3750 Series switches, an innovative product line that improves LAN

More information

Cisco Solution Incentive Program Asia Pacific

Cisco Solution Incentive Program Asia Pacific Channel Incentive Offerings Cisco Solution Incentive Program Asia Pacific User Guide This program will expire on December 31, 2006. Cisco Systems reserves the right to cancel or modify this program at

More information

Using the Catalyst 1900 Series Telco Mounting Brackets

Using the Catalyst 1900 Series Telco Mounting Brackets Text Part Number: 78-5332-02 Using the Catalyst 1900 Series Telco Mounting Brackets June 4, 1999 This document provides instructions for using the telco mounting brackets supplied with the Catalyst 1924-EN-DC

More information

Calling Name Delivery (CNAM)

Calling Name Delivery (CNAM) Calling Name Delivery (CNAM) Document Release History Publication Date June 25, 2007 Comments Initial version of the document. Feature History Release Modification 9.7(3) The Calling Name Delivery (CNAM)

More information

Installing ONS 15454 SDH DS3iN-12 Cards

Installing ONS 15454 SDH DS3iN-12 Cards Product Name: 15454E-DS3IN-12= This document contains a description of DS3iN-12 card features, installation procedures, removal instructions, and technical specifications. Use this document in conjunction

More information

Installing Cisco Security Agent for Cisco Intelligent Contact Management Software, Release 6.0(0)

Installing Cisco Security Agent for Cisco Intelligent Contact Management Software, Release 6.0(0) Installing Cisco Security Agent for Cisco Intelligent Contact Management Software, Release 6.0(0) October 2004 This document provides installation instructions and information about Cisco Security Agent

More information

CISCO 7604 ROUTER. Figure 1. Cisco 7604 Router

CISCO 7604 ROUTER. Figure 1. Cisco 7604 Router DATA SHEET CISCO 7604 ROUTER PRODUCT OVERVIEW The Cisco 7604 Router is one of the smallest, redundant routers to offer n x 10 Gigabit Ethernet performance with services. This router is part of the Cisco

More information

Cisco Data Center Infrastructure Design Guide 2.1 Release Notes

Cisco Data Center Infrastructure Design Guide 2.1 Release Notes Cisco Data Center Infrastructure Design Guide 2.1 Release Notes Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS

More information

End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 2970 Series Switches

End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 2970 Series Switches Product Bulletin No. EOL1092 End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 2970 Series Switches Cisco Systems announces the end-of-sale and end-of-life dates for Cisco Catalyst 2970 Series

More information

CISCO NETWORK ANALYSIS SOFTWARE 3.4

CISCO NETWORK ANALYSIS SOFTWARE 3.4 PRODUCT BULLETIN NO. 2764 CISCO NETWORK ANALYSIS SOFTWARE 3.4 Cisco Systems is proud to announce Cisco Network Analysis Module (NAM) Software 3.4 for both the Cisco Catalyst 6500 and Cisco 7600 Series

More information

CISCO CATALYST EXPRESS 500 SERIES SWITCHES

CISCO CATALYST EXPRESS 500 SERIES SWITCHES Q&A CISCO CATALYST EXPRESS 500 SERIES SWITCHES GENERAL What are the Cisco Catalyst Express 500 Series switches? The Cisco Catalyst Express 500 Series switches deliver Cisco class networking tailored for

More information

CISCO NETWORK CONNECTIVITY CENTER MPLS MANAGER 1.0

CISCO NETWORK CONNECTIVITY CENTER MPLS MANAGER 1.0 DATA SHEET CISCO NETWORK CONNECTIVITY CENTER MPLS MANAGER 1.0 Cisco Network Connectivity Center (NCC) Multiprotocol Label Switching (MPLS) Manager maximizes the availability of VPNs based on MPLS technology.

More information

Installation Guide for Cisco Unified ICM/Contact Center Enterprise and Hosted Release 9.0(1)

Installation Guide for Cisco Unified ICM/Contact Center Enterprise and Hosted Release 9.0(1) Installation Guide for Cisco Unified ICM/Contact Center Enterprise and Hosted Release 9.0(1) First Published: June 21, 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA

More information