Operating Manual. Component Video and Digital Audio Balun KD-CAT5XRCA(1*)

Transcription

1 Component Video and Digital Audio Balun Key Digital, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge Operating Manual technology solutions for virtually all applications where high quality video imaging is important. Key Digital is at the forefront of the video industry for Home Theater etailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers. We provide total video system solutions because we know and help drive the technology, the industry, the business, and all the latest up-and-coming standards. But most of all, we know exactly what you need for your unique application - the right solution. KD-CAT5XCA(1*) KD-C5CWP KD-CAT5XBNC The BobCAT Series devices will convert analog video and analog or digital audio sources for transmission over CAT5 and CAT6 wire. The BobCAT Series devices will act as a transmitting or receiving unit. Please read all warnings and CAT5 distance limitations inside the manual. *Model number KD-CAT5XCA1 contains additional cable accessories for connection to a source unit and/or display. 521 East 3rd Street, Mount Vernon, NY Phone :: Fax :: Web :: ev 0 March 2007

2 Table of Contents Quick Set Up Guide Pr (red cable) Y (green cable) Pb (blue cable) Analog BobCAT Series KD-CAT5XCA / KD-CAT5XBNC / KD-C5CWP Dolby 7.1 Audio Application Example Installation Instructions GBHV Video plus / Audio Application Example Additional Installation Tips Component (YPrb) Video with 5-Channel Surround Application Example PCM/CV (digital audio/ coaxial audio) J45 (CAT5) Cable Pinout Cable Distance and Supporting esolution Dispwitch Settings Troubleshooting Technical Specifications Safety instructions (Please adjust DIP switch Settings, found on page 9) Product Warnings Up to 700 ft. (Please see Distance limitations Found on page 8) Warranty How to Contact Key Digital Pr (red cable) Y (green cable) Analog BobCAT Series KD-CAT5XCA / KD-CAT5XBNC / KD-C5CWP Please read all instructions to insure safe operation of the product. Pb (blue cable) 2007 Key Digital, Inc. All rights reserved. PCM/CV (digital audio/ coaxial audio)

3 Installation Instructions Dolby 7.1 Audio Application Example (Four Box Setup) 1. Find a safe and convenient location for your Analog BobCAT unit. C C S Box 1 x Box 1 Tx S Before permanently securing the unit or final installation of cabling behind walls or ceilings, test for proper operation of the unit and the cables in your system. 2. Connect your Component Video sources to the Component Video ports of the BobCAT intended as the transmitting device. Please note that each Analog BobCAT can be used as either the transmitting or receiving device. Therefore, it makes no difference in the order in which they are connected. Additionally, any BobCAT unit (whether CA, BNC connector or Wall Plate version) is interchangeable and can be used with any other BobCAT version. 3. Connect your Coaxial Digital Audio source to the PCM port of the BobCAT intended as the transmitting device. The BobCAT supports any PCM signal, including standard eft/ight digital audio S S side side side side and Dolby Digital encoded bit streams. If you are not running audio with video through the BobCAT, simply leave this port disconnected. 4. Connect one end of your CAT 5 cable to the CAT 5 port of the BobCAT intended as the transmitting device and the other end of your CAT 5 cable to the CAT 5 port of the BobCAT intended as the receiving device. Use standard CAT 5 cable for interconnectivity between each set of BobCAT Sub Box 2 Tx Box 2 x Sub devices. 5. Connect the Component Video ports of the BobCAT intended as the receiving device to the Component inputs of your receiving device (display, switcher, etc ). 6. Connect the PCM port of the BobCAT intended as the receiving device to the Coaxial Digital Audio inputs of your receiving device (display, A/V receiver, etc ). Again, if you are not running audio with video through the BobCAT, simply leave this port disconnected.

4 Additional Installation Tips GBHV Plus / Audio Application Example (Four Box Setup) ANY input on BobCAT can be used for any of the following video/ audio signals as long as you use the same output on the termination unit. Y,Pr,Pb,,G,B,H,V, S-Video, Composite Video (CV), eft Front Audio, ight Front Audio, Center Speaker, Subwoofer, eft ear Audio, ight ear audio (Any Audio configurations from and beyond). In some cases this requires a multi-box application. Box 1 Tx Box 1 x G G The BobCAT is incredibly flexible in its possible uses. In addition to the standard setup as a Component Video and PCM Digital Audio extender, the unit can also be used for other signals. The following signals are all supported on any BobCAT port, regardless of the silk screened labels on the case. Analog Audio Signals (line level) H and V Sync Signals Composite Video Signals Any YPbPr Signal (whatever the sync configuration may be) GB with Composite Sync (four coaxial line) With the above information in mind, you can see how the additional setup options below make the BobCAT a powerful and useful tool in any installation*. Example One Four BobCAT Setup to support GBHV with / Analog Audio B B H H Box 2 Tx Box 2 x V V In this case, we can use two BobCAT units to transmit GBHV signals in addition to left and right line level analog audio signals over two CAT 5 cables. To do so: 1. Connect GB cables to corresponding ports labeled, G, and B on the first transmitting BobCAT. 2. Connect H sync cable to the port labeled PCM on the first transmitting BobCAT. 3. Connect V Sync cable to the port labeled PCM on the second transmitting BobCAT. 4. Connect left analog audio signal to the port labeled on the second transmitting BobCAT. 5. Connect right analog audio signal to the port labeled G on the second transmitting BobCAT. Use two additional BobCAT units to receive the two CAT 5 cables from the transmitting units above. Take care to connect output cables (GBHV and / audio) to the ports that correspond to those used for input on the transmitting BobCAT.

5 Additional Installation Tips Component (YPrPb) Video with 5-Channel Surround Application Example (Four Box Setup) Example Two Four BobCAT Setup to support GB with Multi-Channel Analog Audio ANY input on BobCAT can be used for any of the following video/ audio signals. As long as you use the same output on the termination unit. Y,Pr,Pb,,G,B,H,V, S-Video (with break-out cable), Composite Video (CV), eft Front Audio, ight Front Audio, Center Speaker, Subwoofer, eft ear Audio, ight ear audio (Any Audio configurations from and beyond). In some cases this requires a multi-box application. Pr Pr Y Y Pb Pb Box 1 x Box 1 Tx C C S S S Box 2 Tx In this case, we can use two BobCAT units to transmit Component Video (GB) signals in addition to multi-channel (, C,, S, S) analog audio. To do so: 1. Connect Component Video cables to the corresponding ports labeled,g, and B on the first transmitting BobCAT. 2. Connect left analog audio signal to the port labeled PCM on the first transmitting BobCAT. 3. Connect the center, right, S, and S analog audio signals to the ports labeled, G, B, and PCM, respectively, on the second transmitting BobCAT. Use two additional BobCAT units to receive the two CAT 5 cables from the transmitting units above. Take care to connect output cables (GB and, C,, S, and S) to the ports that correspond to those used for input on the transmitting BobCAT. Box 2 x S *Note that these are just two examples of the many different possible configurations. If you keep in mind that inputs and outputs should be one-to-one (that is, the signal feeding a specified port on the transmitting BobCAT can be output on the corresponding port on the receiving BobCAT) then there are many uses for multiple BobCAT setups with the formats mentioned above. Additionally, the BobCAT units DIP switches connect shield to when set to On. Switch 1 is for port, switch 2 is for G port, switch 3 is for B port, and switch 4 is for PCM port. Connecting shield to can help eliminate visible noise on the video signal. See Troubleshooting section of this manual.

6 J45 (CAT5) Cable Pinout DIP Switch Settings J45 Pin Wire Color 1 White/Green 2 Green 3 White/Orange 4 Blue 5 White/Blue 6 Orange 7 White/Brown 8 Brown Composite Video: 480p 576i ON OFF 1 PCM/CV connected to PCM/CV is not connected to 2 Pb connected to Pb is not connected to 3 Y connected to Y is not connected to 4 Pr connected to Pr is not connected to Troubleshooting Cable Distance and Supporting esolution Component Video: DIP switch PCM Digital Audio: CAT5 Cable ength 480i 576p 720p i Problem Solution Display has visible lines and/or colors appear incorrectly. A device or cable in the system may not be properly grounded. eplace Component cables. Also, set DIP switch settings on the BobCAT individually to on/off positions. These switches connect (on) / disconnect (off) cabling to. Display drops in/out in intervals. Cable length may be too long for desired resolution. Shorten CAT 5 cable length or lower the resolution you are using. Audio drops in/out in intervals PCM digital audio signals should run reliably up to 500 feet. If audio drops out at lengths above this, try a shorter CAT 5 cable length. Note: Performance for Shielded (STP) and Unshielded (UTP) cables is identical.

7 Page 10 Page 11 Technical Specifications Safety Instructions. Please be sure to follow these instructions for safe operation of your unit. BobCAT Series 1. ead these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the KD-CAT5XCA(1*) KD-C5CWP KD-CAT5XBNC * Model number KD-CAT5XCA1 contains additional cable accessories for connection to a source unit and/or display. manufacturer s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer. Connectors 10. efer all servicing to qualified service personnel. Servicing is required when the One set of Component Video ports (In or Out) labeled, G, B with the following apparatus has been damaged in any way, such as power-supply cord or plug is connectors: YPbPr coaxial analog video connectors. One PCM Digital Audio port (In or Out) labled PCM : Coaxial PCM audio connector on black female CA jack. One CAT5 port (In or Out) labled CAT 5 : Standard CAT 5 J45 jack. damaged, liquid has been spilled or objects have fallen into the apparatus, the Mechanical No fan noise Product Weight: < 1 lb Enclosure type: Molded ABS Plastic apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

8 Page 12 Page 13 Important Product Warnings: How to Contact Key Digital Always test all connections, especially self-made CAT5 cable and Component cables coming into the device. Please set all DIP switch configurations appropriately. DIP switches connect shield to when set to On. Switch 1 is for port, switch 2 is for G port, switch 3 is for B port, and switch 4 is for PCM port. Connecting shield to can help eliminate visible noise on the video signal. See Troubleshooting section of this manual. If installing the analog bobcat into wall or mounting bracket into sheet-rock, provide proper screw support with bolts or sheet-rock anchors. 1. Quality of CAT5 cable. 2. CAT5 crimping or creating the connection yourself must be done as thoroughly as possible or picture quality and/or cable distance will suffer. 3. Do not pull hard or force CAT5 cable, there is a high chance it may break. Warranty Distances for CAT5 are suggestive and depend on the following factors: All Key Digital products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a limited two-year parts and labor warranty. epairs and Warranty Service Should your product require warranty service, please contact Key Digital to obtain a eturned Materials Authorization (MA) number Please contact us at either: Phone: ext rma@keydigital.com Technical Support For technical questions about using our products, please contact us at either: Phone: ext 216 Phone: ext tech@keydigital.com Customer Support For customer support questions about using our products, please contact us at either: Phone: ext customersupport@keydigital.com Feedback Please any comments/questions about the manual to: customersupport@keydigital.com