1. Division-5 Section Metal Fabrications for material and welding requirements related to wrought iron fencing.

Size: px
Start display at page:

Download "1. Division-5 Section Metal Fabrications for material and welding requirements related to wrought iron fencing."

Transcription

1 SECTION SITE FENCES AND GATES PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section SUMMARY A. This Section includes the following: backstops. 1. Galvanized steel chain link fence, gates and baseball/softball 2. Wrought iron fencing. B. Related Sections: The following sections contain requirements that relate to this section: 1.03 SUBMITTALS 1. Division-5 Section Metal Fabrications for material and welding requirements related to wrought iron fencing. 2. Division-9 Section Painting for field painting of wrought iron fencing. A. Product data in the form of manufacturer's technical data, specifications, and installation instructions for fence and gate posts, fabric, gates, and accessories. B. Shop drawings showing location of fence, gates, each post and details of post installation, extension arms, gate swing, hardware, and accessories QUALITY ASSURANCE A. Single-Source Responsibility: Obtain chain link fences and gates as complete units including necessary erection accessories, fittings, and fastenings from a single source or manufacturer.

2

3 PART 2 - PRODUCT 2.01 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 2.02 FABRIC 1. Galvanized Steel Fencing and Fabric: a. Allied Tube and Conduit Corp. b. American Chain Link Fence Company c. Associated Fence Specialists d. Master Halco A. Selvage: All mesh shall be knuckled at both selvages. B. Steel Fabric: Comply with Chain Link Fence Manufacturers Institute (CLFMI) Product Manual. Furnish one-piece fabric widths for fencing up to 12-feet high. Wire size includes zinc or aluminum coating. 1. Size: 2-inch mesh, 9-gage (0.148-inch diameter) wire. C. Galvanized Steel Finish: ASTM A 392, Class 2, with not less than 2.0-oz. zinc per sq. ft. of uncoated wire surface on wire coated before weaving, or not less than 2.0-oz. zinc per sq. ft. of uncoated wire surface, on wire of fabric coated after weaving, as determined from the average of two or more samples, and not less than 1.8-oz. zinc per sq. ft. of uncoated wire surface, for any individual sample FRAMING A. Strength requirements for posts and rails conforming to ASTM F 669. B. Pipe shall be straight, true to section, material, and sizes specified, and shall conform to the following weights per foot:

4 NPS in Outside Diameter Type I Type II inches (OD) in inches Steel Steel / / / / C. Steel Framework, General: Posts, rails, braces, and gate frames. 1. Type II Pipe: Pipe manufactured from steel, conforming to ASTM A 569, cold-formed, high frequency or induction welded, and having minimum yield strength of 50,000 psi. External surface triple coated per ASTM F-1234, Type B & Type D, with 1.0-ounce +/-0.1-ounce of zinc per square inch, and high performance polymer, and shall demonstrate the ability to resist 1,000-hours of exposure to salt spray with a maximum of 5% red rust in a test conducted in accordance with ASTM B-117. Internal surface coated after welding with a zinc-rich based organic coating having a 91% zinc powder loading, capable of providing the ability to withstand 650-hours of exposure to salt fog, with a maximum of 5% red rust when conducted in accordance with ASTM B All coatings to be applied inside and out after welding. D. End, corner, and pull posts for following fabric heights: 1. Up to 6-feet: inch OD Type I or II steel pipe, 2-inch square galvanized steel tubing weighing 2.60-lb. per lin. ft., or 3.5-inch by 3.5-inch roll-formed sections weighing 4.85-lb. per lin. ft. 2. Over 6-feet: inch OD Type I or II steel pipe, 2.50-inchsquare steel tubing weighing 5.10-lbs. per lin. ft., or 3.5-inch by 3.5-inch roll-formed sections weighing 4.85-lbs. per lin. ft.

5 E. Line or intermediate posts for following fabric heights: 1. Up to 6-feet: 1.90-inch OD Type II steel pipe, inch by inch C section weighing 2.28-lb. per lin. ft., or 2.25-inch x 1.70-inch galvanized steel H section weighing 3.26-lb. per lin. ft. 2. Over 6-feet: inch OD Type II steel pipe, 2.25-inch by inch C section weighing 2.70-lbs. per lin. ft., or 2.25-inch by inch galvanized steel H section weighing 3.26-lb. per lin. ft. F. Gate Posts: Furnish posts for supporting single gate leaf or one leaf of a double gate installation for nominal gate widths as follows: 1. Up to 6-feet: inch OD Type II steel pipe, 2.50-inch square galvanized steel tubing weighing 5.10-lbs. per lin. ft., or 3.5-inch x 3.5-inch roll-formed sections weighing 4.85-lbs. per lin. ft. 2. Over 6-feet to 13-feet: 4.00-inch OD Type I or II steel pipe. 3. Over 13-feet to 18-feet: inch OD Type I steel pipe. 4. Over 18-feet: inch OD Type I steel pipe. G. Top Rail: Manufacturer's longest lengths with expansion-type couplings, approximately 6-inches long for each joint. Provide means for attaching top rail securely to each gate corner, pull, and end post. 1. Galvanized Steel: 1-1/4-inch NPS (1.66-inch OD) Type I or II steel pipe or inch by 1.25-inch roll-formed C sections weighing 1.35-lb. per ft FITTINGS AND ACCESSORIES A. Material: Comply with ASTM F 626. Mill-finished aluminum or galvanized iron or steel to suit manufacturer's standards. 1. Zinc Coating: Unless specified otherwise, galvanize steel fence fittings and accessories in accordance with ASTM A 153, with zinc weights per Table I. B. Tension Wire: inch-diameter metallic-coated steel marcelled tension wire conforming to ASTM A 824 with finish to match fabric.

6 1. Type II Zinc Coated: Class 2, with a minimum coating weight of 1.20-oz. per sq. ft. of uncoated wire surface. C. Tie Wires: 12-gage (0.106-inch diameter) galvanized steel with a minimum of 0.80-oz. per sq. ft. of zinc coating of surface area in accordance with ASTM A 641, Class 3. D. Post Brace Assembly: Manufacturer's standard adjustable brace at end and gate posts, and at both sides of corner and pull posts, with horizontal brace located at midheight of fabric. Use same material as top rail for brace and truss to line posts with 3/8-inch-diameter rod, and adjustable tightener. Provide manufacturers standard galvanized steel or cast iron or cast aluminum cap for each end. E. Post and Line Caps: Provide weathertight closure cap for each post. Provide line post caps with loop to receive top rail. F. Tension or Stretcher Bars: Hot-dip galvanized steel with minimum length 2-inches less than full-height of fabric, minimum cross-section of 3/16- inch by 3/4-inch, and minimum 1.2-oz. zinc coating per sq. ft. of surface area. Provide one bar for each gate and end post, and two for each corner and pull post, except where fabric is integrally woven into post. G. Tension and Brace Bands: Minimum 3/4-inch-wide hot-dip galvanized steel with minimum 1.2-oz. zinc coating per sq. ft. of surface area. 1. Tension Bands: Minimum 14-gage (0.074-inch) thick. 2. Tension and Brace Bands: Minimum 12-gage (0.105-inch) thick. H. Concrete: Provide concrete consisting of Portland cement, ASTM C 150 aggregates, ASTM C 33 and clean water. Mix materials to obtain concrete with a minimum 28-day compressive strength of 2500 psi. Use at least 4 sacks of cement per cu. yd., 1-inch maximum size aggregate, maximum 3- inch slump, and 2 to 4 percent entrained air GATES A. Fabrication: Fabricate perimeter frames of gates from metal and finish to match fence framework. Assemble gate frames by welding. Provide horizontal and vertical members to ensure proper gate operation and attachment of fabric, hardware, and accessories. Space frame members maximum of 8-feet apart unless otherwise indicated.

7 1. Provide same fabric as for fence unless otherwise indicated. Install fabric with tension bars and bands at vertical edges and at top and bottom edges. 2. Install diagonal cross-bracing consisting of 3/8-inch-diameter, adjustable-length truss rods on gates, to ensure frame rigidity without sag or twist. B. Swing Gates: Comply with ASTM F Steel: a. Up to 6-feet High and 8-feet Wide: Fabricate perimeter frames of minimum inch OD Type I or II steel pipe, or 1.50-inch square galvanized steel tubing, weighing lb per sq ft. b. Over to 6-feet High and 8-Feet Wide: Fabricate perimeter frames of minimum 1.90-inch OD Type I or II steel pipe, or 2.00-inch square galvanized steel tubing, weighing 2.60-lb per sq ft. 2. Gate Hardware: Provide hardware and accessories for each gate, galvanized per ASTM A 153, and in accordance with the following: a. Hinges: Size and material to suit gate size, non-lift-off type, offset to permit 180-deg gate opening. Provide 1-1/2 pair of hinges for each leaf over 6-foot nominal height. b. Latch: Forked type or plunger-bar type, to permit operation from either side of gate, with padlock eye as integral part of latch BASEBALL/SOFTBALL BACKSTOPS A. General: Provide backstops in configurations and size indicated, with 9- gage, 2-inch mesh fabric throughout, with galvanized finish as indicated in Fabric Article of this Section. 1. Line Posts: 2-inch NPS, (2.375-inch OD). 2. Rail: 1-1/2-inch NPS, (1.900-inch OD). 3. Terminal Posts: 4-inch NPS, (4.500-inch OD).

8

9 4. Fittings: Pressed or malleable steel, with galvanized finish (2- ounce/sq. ft.) per ASTM A Bottom Plate: 3/16-inch thickness galvanized steel plate, 12- inches high, for installation along bottom edge of backstop. Furnish plate in greatest lengths possible to minimize number of joints. Indicate details of proposed attachment in Shop Drawings WROUGHT IRON FENCING A. General: Provide 5-foot high, banister style fencing with all welded connections, with 8-foot maximum rail sections, 4-foot, 9-inches between top and bottom rail unless otherwise indicated. Comply with requirements of Division-5 Section Metal Fabrications for materials, shop priming and welding requirements; comply with requirements of Division-9 Section Painting for field painting. Fences shall be painted to match school color scheme. 1. Line Posts: 2-inch square (unless otherwise indicated) steel posts, 16-gage thickness, with pressed steel post cap, tack-welded in place. 2. Top and Bottom Rails: 2-inch square, 16-gauge steel. 3. Pickets: 3/4-inch square steel, 16-gauge, spaced at 4-1/2 -inches o.c. 4. Connections: Weld all connections 4 sides. 5. Gates: Fabricate all gate frames of 2-inch, 16-gage square steel. Brace as required to ensure frames remain square. a. Posts: For single leaf gates up to 8-feet wide, provide 4- inch square 16-gage steel posts; for gates 8-feet and wider, provide 4-inch square, 11-gage posts. For double gates 30- feet wide and up, provide 6-inch square steel tubes with 1/4-inch minimum wall thickness. b. Hinges: Provide heavy duty butt hinges for gates up to 5- feet; provide heavy duty ball bearing hinges for gates greater than 5-feet in width, by Builders Fence Company or approved equal. Provide two hinges minimum per leaf. c. Other Hardware: Provide hardware or anchors at each gate to allow gates to be locked open.

10

11 PART 3 - EXECUTION 3.01 INSTALLATION A. General: Install fence in compliance with ASTM F 567. Do not begin installation and erection before final grading is completed unless otherwise permitted. 1. Apply fabric to outside of framework. Install fencing on boundary lines, inside of property line, established by survey as required by Division 1. B. Excavation: Drill or hand-excavate (using post-hole digger) holes for posts to diameters and spacings indicated, in firm, undisturbed, or compacted soil. 1. If not indicated on drawings, excavate holes for each post to minimum diameter recommended by fence manufacturer, but not less than 4 times largest cross-section of post. 2. Unless otherwise indicated, excavate hole depths approximately 3- inches lower than post bottom, with bottom of posts set not less than 36-inches below finish grade surface. C. Setting Posts: Center and align posts in holes 3-inches above bottom of excavation. Space maximum 10-feet o.c., unless otherwise indicated. 1. Protect portion of posts above ground from concrete splatter. Place concrete around posts and vibrate or tamp for consolidation. Check each post for vertical and top alignment and hold in position during placement and finishing operations. 2. Unless otherwise indicated, extend concrete footings 2-inches above grade, and trowel to a crown to shed water. D. Top Rails: Run rail continuously through line post caps, bending to radius for curved runs, and at other posts terminating into rail end attached to posts or post caps fabricated to receive rail. Provide expansion couplings as recommended by fencing manufacturer. E. Brace Assemblies: Install braces so posts are plumb when diagonal rod is under proper tension.

12 F. Bottom Tension Wire: Install tension wire within 6-inches of bottom of fabric before stretching fabric, and tie to each post with not less than same gage and type of wire. Pull wire taut, without sags. Fasten fabric to tension wire with 11-gage hog rings of same material and finish as fabric wire, spaced maximum 24-inches o.c. G. Fabric: Leave approximately 2-inches between finish grade and bottom selvage unless otherwise indicated. Pull fabric taut, and tie to posts, rails, and tension wires. Install fabric on security side of fence and anchor to framework so that fabric remains in tension after pulling force is released. H. Tension or Stretcher Bars: Thread through or clamp to fabric 4-inches o.c., and secure to end, corner, pull, and gate posts with tension bands, spaced not over 15-inches o.c. I. Tie Wires: Use U-shaped wire of proper length to secure fabric firmly to posts and rails, with ends twisted at least 2 full turns. Bend ends of wire to minimize hazard to persons or clothing. 1. Maximum Spacing: Tie fabric to line posts 12-inches o.c. and to rails and braces 24-inches o.c. J. Fasteners: Install nuts for tension bands and hardware bolts on side of fence opposite fabric side. Peen ends of bolts or score threads to prevent removal of nuts. K. Gates: Install gates plumb, level and secure for full opening without interference. Install ground-set items in concrete for anchorage. Adjust hardware for smooth operation and lubricate where necessary. L. Wrought Iron Fencing: Set bottom rails 6-inches maximum above final grade, 2-inches minimum above finish grade. Fence sections may be stepped to maintain spacing. **END OF SECTION**

SECTION CHAIN LINK FENCE AND GATES

SECTION CHAIN LINK FENCE AND GATES SECTION 02830 CHAIN LINK FENCE AND GATES PART 1 GENERAL 1.01 SCOPE OF WORK The work covered in this section shall include all materials, labor, and equipment necessary for a complete installation of the

More information

1. Division 2 Section "Earthwork" for filling and for grading work. 2. Division 3 Section "Cast-in-Place Concrete" for concrete

1. Division 2 Section Earthwork for filling and for grading work. 2. Division 3 Section Cast-in-Place Concrete for concrete SECTION 02821 - FENCES AND GATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

MATERIAL SPECIFICATIONS

MATERIAL SPECIFICATIONS FENCING - 1 2-11-1 CHAIN LINK FENCE AND GATE(S) A. SCOPE MATERIAL SPECIFICATIONS This section covers the work necessary for the chain link fence gate(s), complete. General Like items of materials provided

More information

SECTION 32 31 13 CHAIN LINK FENCES AND GATES

SECTION 32 31 13 CHAIN LINK FENCES AND GATES SECTION 32 31 13 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Fence framework, fabric, and accessories. 2. Excavation for post bases. 3. Concrete foundation for posts

More information

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings. SECTION 32 31 13 CHAIN LINK FENCES PART 1 GENERAL 1.1 SUMMARY A. This Section includes: 1. Galvanized fence framework, fabric, and accessories. 2. Excavation for post bases, and concrete for post footings.

More information

SECTION 02832 CHAIN LINK FENCE AND GATES

SECTION 02832 CHAIN LINK FENCE AND GATES SECTION 02832 CHAIN LINK FENCE AND GATES PART 1 GENERAL 1.01 SECTION INCLUDES A. Fabrication, furnishing and installation of chain link fence, chain link gates, and extension brackets with barbed wire.

More information

SECTION 63 CHAIN-LINK FENCES (FAA F-162) ITEM F-162 CHAIN-LINK FENCES DESCRIPTION MATERIALS

SECTION 63 CHAIN-LINK FENCES (FAA F-162) ITEM F-162 CHAIN-LINK FENCES DESCRIPTION MATERIALS SECTION 63 CHAIN-LINK FENCES (FAA F-162) 63-1 GENERAL This specification covers the furnishing and installation of chain link fencing and gates, both permanent and temporary, at the locations shown on

More information

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12

The Manitoba Water Services Board SECTION 027110 Standard Construction Specifications September 2013 Page 1 of 12 September 2013 Page 1 of 12 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work shall consist of the supply and construction of a chain link fence, barb wire fences or mesh fences as shown on the Plans or

More information

SECTION 32 31 13 CHAIN LINK FENCES AND GATES

SECTION 32 31 13 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.1 DESCRIPTION SECTION 32 31 13 CHAIN LINK FENCES AND GATES SPEC WRITER NOTES: 1. Delete or add information between //---// and any other items applicable to project. Cover any item added

More information

SECTION 02824 EXPANDED METAL MESH FENCE

SECTION 02824 EXPANDED METAL MESH FENCE SECTION 02824 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for expanded metal mesh fence on the right-of-way. 1.02 REFERENCE STANDARDS A. ASTM International (ASTM): 1.03 SUBMITTALS

More information

MERCHANTS METALS SECTION 32 31 13 ARMORLINK ALUMINIZED CHAIN LINK FENCE AND GATES 2014!

MERCHANTS METALS SECTION 32 31 13 ARMORLINK ALUMINIZED CHAIN LINK FENCE AND GATES 2014! MERCHANTS METALS SECTION 32 31 13 ARMORLINK ALUMINIZED CHAIN LINK FENCE AND GATES 2014 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance

More information

SECTION 32 31 00 EXPANDED METAL FENCING Meets Buy American Procurement

SECTION 32 31 00 EXPANDED METAL FENCING Meets Buy American Procurement PART 1 GENERAL SECTION 32 31 00 EXPANDED METAL FENCING Meets Buy American Procurement 1.1 SUMMARY A. Section Includes 1. Supply and install all materials and accoutrements required for the installation

More information

CHAIN LINK FENCES & GATES

CHAIN LINK FENCES & GATES CITY OF BRAMPTON LANDSCAPE SPECIFICATIONS SECTION 02821-1 PART 1 GENERAL 1.1 Related Work.1 All Division 1 Specification Sections.2 Section 02867 Junior and Senior Softball Backstop.3 Section 02868 Backstops.4

More information

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM):

AIRPORT SECURITY FENCING. A. American Society for Testing and Materials (ASTM): SECTION 02832 AIRPORT SECURITY FENCING PART 1-GENERAL 1.1 SUMMARY A. Section includes: Construct airport security chain-link fence and gate at specified areas and conforming lines, grades, details indicated

More information

CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION

CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION CHAIN-LINK FENCES BID SPECIFICATIONS DESCRIPTION 1 This item shall consist of furnishing and erecting Chain-Link fence in accordance with these specifications and the details shown on the plans and in

More information

2015 CATALOGUE Industrial Products and Price List

2015 CATALOGUE Industrial Products and Price List McGowan Fence & Supply Limited 811 Progress Avenue Scarborough, Ontario M1H 2X4 Tel (416)431-5556 Fax (416)431-2595 2015 CATALOGUE Industrial Products and Price List QUALITY and Service Since 1948 TERMS

More information

WELDED ORNAMENTAL FENCE SYSTEM ENTER PROJECT NAME HERE 09/2010

WELDED ORNAMENTAL FENCE SYSTEM ENTER PROJECT NAME HERE 09/2010 SECTION 32 31 00 FENCES AND GATES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions. 1.2 SUMMARY A. This Section includes

More information

1.3 SUBMITTALS Follow 01330

1.3 SUBMITTALS Follow 01330 02830 CHAIN LINK FENCES AND GATES Specifier: This section replaces 02831 (2004). It reflects significant changes in and additions to ASTM documents in recent years that relate to chain link fence and gates.

More information

INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE

INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE Fencing Without Boundaries TM 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally established property lines.

More information

Bands. REGULAR BRACE BANDS 12 GA. x 3/4 Galvanized. REGULAR TENSION BANDS 14 GA. x 3/4 Galvanized Sack Weight Price Each

Bands. REGULAR BRACE BANDS 12 GA. x 3/4 Galvanized. REGULAR TENSION BANDS 14 GA. x 3/4 Galvanized Sack Weight Price Each Bands REGULAR TENSION BANDS 14 GA. x 3/4 Galvanized Sack Weight Item# Qty. Less Sack Sack 1 3/8" 1 250.12 lbs..36.30 1 5/8" 2 250.14 lbs..38.32 1 7/8" 3 250.16 lbs..40.33 2 3/8" 4 250.22 lbs..42.35 2 7/8"

More information

How to secure your property after a disaster

How to secure your property after a disaster How to secure your property after a disaster The Red Guide to Recovery HOuse secured properly Board-Up of Windows, Doors and Roof Hole. Lot secured with Perimeter Fencing. Fires, floods, tornadoes, hurricanes,

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-32 31 26 (April 2008) -------------------------- Preparing Activity: USACE Superseding UFGS 32 31 26 (January 2008) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5

The City of Winnipeg Section Turtle Island Community Centre Renovation Page 1 of 5 Turtle Island Community Centre Renovation Page 1 of 5 Part 1 General 1.1 SECTION INCLUDES.1 Shop fabricated ferrous metal items..2 Shop fabricated aluminum items..3 Steel pipe handrails balusters, and

More information

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION 08332 COILING COUNTER DOORS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 08332 COILING COUNTER DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Coiling Metal Counter Doors. B. Coiling Counter Fire Doors. 1.2

More information

Fence SpecCheck Wheatland Tube Company 800 343 0124

Fence SpecCheck Wheatland Tube Company 800 343 0124 Fence SpecCheck Wheatland Tube Company 800 343 0124 www.wheatland.com ASTM Specifications (May 2014) www.astm.org A53/A53M-12 Schedule 40 & 80 Pipe: Specification for Pipe, Steel, Black and Hot- Dipped,

More information

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS

SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word

More information

FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES)

FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES) INCH-POUND RR-F-191/3E AMENDMENT 1 29 OCTOBER 2007 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST, METAL (CHAIN-LINK FENCE POSTS, TOP RAILS AND BRACES) The General Services Administration has authorized

More information

SECURA FENCE SYSTEM RETROFIT

SECURA FENCE SYSTEM RETROFIT The Secura Fence System is available in several gauges of steel and various mesh sizes and can be used on new construction or to add much needed security to existing fence barriers. The panels are made

More information

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5

Generic Technical Performance Specification GTS-1653 February 2001 Issue: 01 Revision: 00 Page 1 of 5 Issue: 01 Revision: 00 Page 1 of 5 1 ASSEMBLY - GENERAL 1.1 The work of this section includes the provision of all design, labour, materials, equipment and services required to fabricate and install stair

More information

PART 1 GENERAL 1.1 SECTION INCLUDES

PART 1 GENERAL 1.1 SECTION INCLUDES J-1 Section 09110 Long Form Specification INTERIOR METAL STUD FRAMING This section includes lightweight, usually 0.036 inch (0.9 mm) thick or lighter, non-axial load bearing metal stud framing including

More information

SECTION METAL STAIRS, LADDERS, AND WALKWAYS

SECTION METAL STAIRS, LADDERS, AND WALKWAYS SECTION 05510 METAL STAIRS, LADDERS, AND WALKWAYS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Technical requirements for metal stairs, ladder, and walkways. 1.2 REFERENCES A. General: References to

More information

EZ Wire. Product Guide. Product Web Page

EZ Wire. Product Guide. Product Web Page EZ Wire Product Guide Product Web Page http://huskyrackandwire.com/products_ patented hook fastener Step 1: Align hooks and insert into slots Step 2: Hammer drive pin for a secure connection Value The

More information

The Kodiak 2400 Seating System by Royal Stewart Ltd.:

The Kodiak 2400 Seating System by Royal Stewart Ltd.: The Kodiak 2400 Seating System by Royal Stewart Ltd.: PART 1 GENERAL 1.1 Description Telescopic Bleacher Seating includes either manually or electrically operated systems of multiple tiered seating rows

More information

PROPER HANGING OF FIRE SPRINKLER SYSTEMS IFSA. All rights reserved.

PROPER HANGING OF FIRE SPRINKLER SYSTEMS IFSA. All rights reserved. PROPER HANGING OF FIRE SPRINKLER SYSTEMS 2010 IFSA. All rights reserved. 1 HANGING PER NFPA 13 2 Historical developments and basic concepts Hangers Hanger installation Special listed pipe Hangers in earthquake

More information

- STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS -

- STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS - - STRONGHOLD IRON FENCE PARTS AND MATERIALS SPECIFICATIONS - PART 1.01: MATERIALS STEEL: All steel material for the fence and gate system shall conform to the requirements of ASTM A- 787 and ASTM A653

More information

C. See Division 5 Section "Pipe and Tube Railings" for metal pipe and tube railings.

C. See Division 5 Section Pipe and Tube Railings for metal pipe and tube railings. SECTION 05 50 00 METAL FABRICATIONS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Miscellaneous steel framing and supports. 2. Metal ladders. 3. Shelf angles. 4. Loose bearing

More information

Single Solid Square Hub Power Driven Anchor

Single Solid Square Hub Power Driven Anchor EA1 Single Solid Square Hub Power Driven Anchor Installation is performed using a power digger. An anchor wrench fits over the anchor hub and a torque measurement device is required to determine proper

More information

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049

Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049 Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal

More information

SECTION 02630 STORM DRAINAGE SYSTEM

SECTION 02630 STORM DRAINAGE SYSTEM SECTION 02630 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for storm drainage systems including modifications and connections to existing storm drainage systems. 1.02 REFERENCE

More information

PTS HELICAL PIERS INSTALLATION SPECIFICATIONS NOTICE

PTS HELICAL PIERS INSTALLATION SPECIFICATIONS NOTICE FORM A PTS HELICAL PIERS INSTALLATION SPECIFICATIONS NOTICE The following suggested specifications are written as a guide to assist the specifier in writing his own specifications. Specific circumstances

More information

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE

SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel

More information

ATLANTA MODEL SPECIFICATIONS

ATLANTA MODEL SPECIFICATIONS ATLANTA MODEL 50 SPECIFICATIONS Dimensions: Roof Dimensions (point to point) 50-0 Column Dimensions (out to out of columns) 44-0 Eave Height 8-0 Roof Height @ Peak ±21-8⅞ Hip Roof 6:12 pitch Square Feet

More information

DENVER MODEL 30 X 30 SPECIFICATIONS

DENVER MODEL 30 X 30 SPECIFICATIONS DENVER MODEL 30 X 30 SPECIFICATIONS Dimensions: Roof Dimensions 30-0 x 30-0 (4) Columns (Center to Center) 25-6½ x 25-6½ Minimum Clearance 8-0 Roof Height @ Peak Dependent on Col. Ht. Hip Roof 4:12 pitch

More information

SECTION 15140 - PIPE HANGERS AND SUPPORTS

SECTION 15140 - PIPE HANGERS AND SUPPORTS Part I - GENERAL 1.01 SECTION INCLUDES A. The work covered under this section consists of the furnishing of all necessary labor, supervision, materials, equipment, and services to completely execute the

More information

COLORADO MODEL. 35 x 65 SPECIFICATIONS

COLORADO MODEL. 35 x 65 SPECIFICATIONS COLORADO MODEL 35 x 65 SPECIFICATIONS Dimensions: Roof Dimensions 35-0 x 65-0 Column Dimensions (center to center) 31-0 x 30-6 Minimum Clearance 14-0 Roof Height @ Peak ±18-8 Curved Roof ±42-6 radius Square

More information

SPECIFICATIONS Rev:

SPECIFICATIONS Rev: SPECIFICATIONS Rev: 060209 Section Helical Steel Piles 1. General 1.1. Description 1.1.1. The work of this section consists of furnishing and installing steel helical piles manufactured by MacLean-Dixie

More information

SECTION 710 GUARDRAIL MATERIALS

SECTION 710 GUARDRAIL MATERIALS 710.08 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 SECTION 710 GUARDRAIL MATERIALS 710.01 General. Metal beam

More information

Residential Deck Safety, Construction, and Repair

Residential Deck Safety, Construction, and Repair Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the

More information

SUPPLEMENTAL TECHNICAL SPECIFICATIONS BI-DIRECTIONAL STATIC LOAD TESTING OF DRILLED SHAFTS

SUPPLEMENTAL TECHNICAL SPECIFICATIONS BI-DIRECTIONAL STATIC LOAD TESTING OF DRILLED SHAFTS July 14, 2015 1.0 GENERAL BI-DIRECTIONAL STATIC LOAD TESTING OF DRILLED SHAFTS This work shall consist of furnishing all materials, equipment, labor, and incidentals necessary for conducting bi-directional

More information

INSTRUCTIONS FOR CHAIN LINK INSTALLATION Chain Link fence & Posts Meshdirect.co.uk

INSTRUCTIONS FOR CHAIN LINK INSTALLATION Chain Link fence & Posts Meshdirect.co.uk INSTRUCTIONS FOR CHAIN LINK INSTALLATION Chain Link fence & Posts Meshdirect.co.uk This guide explains how to correctly install our chain link fencing and post system. The guide provides details of the

More information

San Antonio Water System Standard Specifications for Construction ITEM NO. 816 STEEL PIPE INSTALLATION

San Antonio Water System Standard Specifications for Construction ITEM NO. 816 STEEL PIPE INSTALLATION ITEM NO. 816 STEEL PIPE INSTALLATION 816.1 DESCRIPTION: This item shall consist of steel pipe installation in accordance with these specifications and as directed by the Engineer. 816.2 SUBMITTALS: Contractor

More information

WHI 90-Minute Rated Veneered Door Frame Installation Instructions

WHI 90-Minute Rated Veneered Door Frame Installation Instructions No. 940-03-10 INSTALLATION INSTRUCTIONS 90 MINUTE RATED VENEERED DOOR FRAME DOOR REQUIREMENTS: Consult the door manufacturer to make sure that the doors are qualified for the hardware to be installed,

More information

Scraper Flight Distribution Conveyor

Scraper Flight Distribution Conveyor SERPENTIX CONVEYOR CORP. 9085 Marshall Ct. Westminster, CO 80031-2920 Phone: 303.430.8427 Fax: 303.430.7337 www.serpentixconveyor.com rob@serpentix.com Scraper Flight Distribution Conveyor SERPENTIX CONVEYOR

More information

Installing Your Bat House - Wooden Post or Steel Pole Installation-

Installing Your Bat House - Wooden Post or Steel Pole Installation- Installing Your Bat House - Wooden Post or Steel Pole Installation- Choose a sunny location to install your bat house pole. Bat houses work best with at least 6-8 hours of direct sunlight (if only partial

More information

SECTION 6. Glass Storefront Doors:

SECTION 6. Glass Storefront Doors: SECTION 6 Glass Storefront Doors: Table of Contents 3070 Storefront Door System Description & Dimensions 6070 Storefront Door System Description & Dimensions Door Leaf Detail Optional 10 Bottom Rail Detail

More information

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041

1036 Parkway Ct. Phone: 770-932-0202 Buford, GA 30518 Fax: 770-945-0041 CONSTRUCTION 1. A. GENERAL 1.A.1. The intent of this specification is to set forth construction and design standards that will result in an installation of modular cabinetry requiring FLUSH OVERLAY CONSTRUCTION.

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-32 31 13.53 (April 2008) ----------------------------- Preparing Activity: USACE Superseding UFGS-32 31 13.53 (January 2008) UNIFIED FACILITIES GUIDE SPECIFICATIONS References

More information

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts.

SECTION METAL BUILDING SYSTEMS. A. Metal wall and roof panels including gutters and downspouts. New Football Stadium 13.34.19-1 PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 13.34.19 METAL BUILDING SYSTEMS A. Metal wall and roof panels including gutters and downspouts. 1.02 RELATED REQUIREMENTS A.

More information

Gatorshield Steel Tubing

Gatorshield Steel Tubing steel tubing Gatorshield Steel Tubing ROUND STEEL TUBING Catalog # Size Gauge Bundle Qty. Price/Foot Price/Piece 014-108-288 1 x 24 18 127 $1.05 $25.20 014-104-288 1 x 24 14 127 $1.47 $35.28 014-104-276

More information

SECTION 02845 GUARDRAILS

SECTION 02845 GUARDRAILS SECTION 02845 GUARDRAILS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals necessary and repair, replace or install all types of guardrails as specified herein

More information

Product Manual CLF-PM0610 (revised January, 2012)

Product Manual CLF-PM0610 (revised January, 2012) Chain Link Fence Manufacturers Institute Product Manual CLF-PM0610 (revised January, 2012) Table of Contents How to Use the Product Manual 1 Description of Terms 2 Table 1 - Breaking Strength of Steel

More information

SECTION ANCHOR BOLTS. A. Provide bolts and nuts that meet the standards given in Table 1.

SECTION ANCHOR BOLTS. A. Provide bolts and nuts that meet the standards given in Table 1. SECTION 16449 PART 1 DESCRIPTION A. Fabricate and install anchor bolts to be embedded in or attached to concrete. PART 2 MATERIALS 2.01 BOLTS AND NUTS A. Provide bolts and nuts that meet the standards

More information

CLEAR-DIVISIONS CENTERFOLD

CLEAR-DIVISIONS CENTERFOLD CLEAR-DIVISIONS CENTERFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS CENTERFOLD moveable The yellow highlighted areas in

More information

.2 Section Waste Management and Disposal..4 Section Testing, Adjusting and Balancing (TAB) of Mechanical Systems.

.2 Section Waste Management and Disposal..4 Section Testing, Adjusting and Balancing (TAB) of Mechanical Systems. Issued 2006/08/01 Section 15072 Vibration Isolation Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal.3 Section 03300 Cast

More information

Fittings REGULAR TENSION BANDS MEDIUM TENSION BANDS BEVELED TENSION BANDS

Fittings REGULAR TENSION BANDS MEDIUM TENSION BANDS BEVELED TENSION BANDS Fittings REGULAR TENSION BANDS 14 ga. x 3/4 1-3/8 010101 250.12 lb. 1-5/8 010102 250.14 lb. 1-7/8 010103 250.15 lb. 2-3/8 010104 250.18 lb. 2-7/8 010105 100.20 lb. 3 Full 010106 100.21 lb. 3-1/2 010107

More information

CAMP U S RAC K. Orderly Bike Parking

CAMP U S RAC K. Orderly Bike Parking CAMP U S RAC K Orderly Bike Parking The design of this bike rack supports the frame of the bike while keeping the fork from twisting. The result is convenient, orderly bike parking. The Campus Rack is

More information

FORM DESIGN. easy to work with, and generally available.

FORM DESIGN. easy to work with, and generally available. Forms play a major role in concrete construction. They give the plastic concrete its shape and hold it until it hardens. Forms protect the concrete, assist in curing it, and support any reinforcing rods

More information

Operating, Servicing, and Safety Instruction Manual Sheet Metal Straight Brake

Operating, Servicing, and Safety Instruction Manual Sheet Metal Straight Brake Operating, Servicing, and Safety Instruction Manual Sheet Metal Straight Brake 16Ga Models #2800-4816S / #2800-7216S / #2800-9616S 22Ga Models #2800-7222S / #2800-9622S CAUTION: Read and Understand These

More information

A. The shade structure contractor shall be responsible for the design, engineering, fabrication, and supply of the work specified herein.

A. The shade structure contractor shall be responsible for the design, engineering, fabrication, and supply of the work specified herein. 13310 FABRIC SHADE STRUCTURES FOR PLAYGROUND AREAS ************************************************************************************************************************ SPECIFIER: CSI Master Format

More information

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS

SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS SECTION 26 05 49 VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for electrical

More information

CLEAR-DIVISIONS VARIOFOLD

CLEAR-DIVISIONS VARIOFOLD CLEAR-DIVISIONS VARIOFOLD Introduction: The following three (3) part specification offers the Standard and Optional features for the CLEAR-DIVISIONS VARIOFOLD moveable The yellow highlighted areas in the

More information

PRODUCT OVERVIEW: "Standard" Product Features and Benefits: Look for these features when comparing similar products.

PRODUCT OVERVIEW: Standard Product Features and Benefits: Look for these features when comparing similar products. POCKET DOORS PRODUCT OVERVIEW: Hufcor offers pocket doors to close the openings of operable wall storage pockets. It has been our experience that one of the types shown in these specifications will work

More information

Light Gauge Metal Trusses Specification Architectural Guide Specification

Light Gauge Metal Trusses Specification Architectural Guide Specification Precision Walls, Inc. 1230 NE Maynard Rd. Cary, NC 27513 Light Gauge Metal Trusses Specification Architectural Guide Specification PART 1: GENERAL * Instructions, options and comments for the specification

More information

MAST ARMS & POLES. Ornamental Pole Top & Bases

MAST ARMS & POLES. Ornamental Pole Top & Bases Ornamental Pole Top & Bases Pelco s decorative pole top and bases help make the traffic signal aesthetically pleasing to the eye. Available for various pole diameters and multiple finish options. Ornamental

More information

Bridge Component Concrete Standard

Bridge Component Concrete Standard Bridge Component Concrete Standard Ministry of Forests, Lands and Natural Resource Operations All concrete bridge component products supplied for the Ministry of Forests, Lands and Natural Resource Operations

More information

Preformed Metal Roofing and Siding

Preformed Metal Roofing and Siding Page -1-1. GENERAL 1.1. Description This specification along with the drawings covers the furnishing of all material, products, equipment, accessories, tools, services, transportation, labor and supervision

More information

TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE

TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE TECHNICAL MANUAL PIPECLAMP JULY 2013 ROHRVERBINDER ONLINESHOP.DE Selecting a Fitting fittings are a blackheart malleable casting and are manufactured to BS EN 1562 1997 for the strength requirements. fittings

More information

Thermal Block Entrance Installation Manual. Thermal Entrances. Installation Instructions. 05/21/14 Tubelite Inc. Page 0 of 20

Thermal Block Entrance Installation Manual. Thermal Entrances. Installation Instructions. 05/21/14 Tubelite Inc. Page 0 of 20 Thermal Entrances Installation Instructions 2010 05/21/14 Tubelite Inc. Page 0 of 20 TABLE OF CONTENTS INSTALLATION NOTES........................................ 2 PARTS LIST........................................

More information

CAST IRON DETECTABLE/TACTILE WARNING SURFACE INDICATOR PLATE

CAST IRON DETECTABLE/TACTILE WARNING SURFACE INDICATOR PLATE CAST IRON DETECTABLE/TACTILE WARNING SURFACE INDICATOR PLATE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions and Division

More information

FORMAL TECHNICAL OPINION

FORMAL TECHNICAL OPINION Jon S. Corzine Governor Issued: March 1985 Revised: June 2001 Code Ref. Update: January 2011 State of New Jersey Department of Community Affairs Division of Codes and Standards PO Box 802 Trenton, New

More information

ARCHITECTURAL PRECAST CONCRETE

ARCHITECTURAL PRECAST CONCRETE CITY OF BRAMPTON LANDSCAPE SPECIFICATIONS SECTION 03450-1 PART 1 GENERAL 1.1 Related Work.1 All Division 1 Specification Sections.2 Section 02233 Granular Base.3 Section 02311 Site Grading.4 Section 03100

More information

Suggested Specification for Hot-Dip Galvanizing Revised May 2002

Suggested Specification for Hot-Dip Galvanizing Revised May 2002 Suggested Specification for Hot-Dip Galvanizing Revised May 2002 This suggested specification is provided as a guide to producing a quality document calling for after-fabrication hot-dip galvanizing of

More information

GLASS WALL POCKET DOORS

GLASS WALL POCKET DOORS GLASS WALL POCKET DOORS KWIK-WALL... One Source for Wall Systems. KWIK-WALL s Pocket Doors for glass wall systems bring you the clear solution to your space division requirements. The beauty and elegance

More information

Chain Link Fence Manufacturers Institute Security Fencing Recommendations

Chain Link Fence Manufacturers Institute Security Fencing Recommendations Chain Link Fence Manufacturers Institute Security Fencing Recommendations Chain link fencing has been the product of choice for security fencing for over 60 years because of its strength, corrosion resistance,

More information

Cut & Bent Bar Reinforcement Mesh Fabric Stockholders Reinforcement Accessories Express Valued Service Quality & Reliability

Cut & Bent Bar Reinforcement Mesh Fabric Stockholders Reinforcement Accessories Express Valued Service Quality & Reliability Your Local Independent Supplier Serving the Construction Industry Cut & Bent Bar Reinforcement Mesh Fabric Stockholders Reinforcement Accessories Express Valued Service Quality & Reliability 911001 LIVERSEDGE

More information

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT

More information

City of Tucson and Pima County Arizona Building Code Appendix Chapter 72 Straw-Bale Structures

City of Tucson and Pima County Arizona Building Code Appendix Chapter 72 Straw-Bale Structures City of Tucson and Pima County Arizona Building Code Appendix Chapter 72 Straw-Bale Structures SECTION 7201 - PURPOSE The purpose of this appendix chapter is to establish minimum prescriptive standards

More information

INSTALLATION OF A BAY WINDOW

INSTALLATION OF A BAY WINDOW INSTALLATION OF A BAY WINDOW Installation of a Bay Window These instructions relate to the replacement of an existing bay window or replacement of a straight window with a new bay window, in an opening

More information

Chapter 3 Pre-Installation, Foundations and Piers

Chapter 3 Pre-Installation, Foundations and Piers Chapter 3 Pre-Installation, Foundations and Piers 3-1 Pre-Installation Establishes the minimum requirements for the siting, design, materials, access, and installation of manufactured dwellings, accessory

More information

SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS

SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS 1 SECTION 05 7360 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH DECORATIVE METAL PANEL INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and

More information

PUMP JACK SYSTEM AND ACCESSORIES

PUMP JACK SYSTEM AND ACCESSORIES Pump Jack Model # 2200 A low cost, easy to operate, safe, portable scaffolding built of rugged steel. It's perfect for shingling, siding, sheathing, insulating, painting, building, roofing, home repair

More information

SECTION 7 FOUNDATIONS

SECTION 7 FOUNDATIONS SECTION 7 FOUNDATIONS TYPICAL CONSTRUCTION METHOD Before any new building is erected, remove all stumps and roots from the soil to a depth of at least 12" below the surface of the ground in the area to

More information

S W E RV E RAC K. Simple Security. Simple Stability.

S W E RV E RAC K. Simple Security. Simple Stability. S W E RV E RAC K Simple Security. Simple Stability. The Swerve Rack is a proven design that provides high security and easy bike parking. The Swerve Rack uses thick pipe construction and the full radius

More information

Panel Installation Manual. Nursery/Finishing Panels

Panel Installation Manual. Nursery/Finishing Panels Panel Installation Manual Nursery/Finishing Panels Identification of Panel Components 1A is a floor plan of the building that will serve an example for the installation of Nursery/Finisher Panels throughout

More information

Chain Link Cantilever Gate Installation Manual

Chain Link Cantilever Gate Installation Manual Chain Link Cantilever Gate Installation Manual Introduction to Cantilever Gates: A cantilever gate is unique in that it 'cantilevers' itself to close an opening while being supported from only one end.

More information

DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS

DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS DIVISION 8, METAL SOUND CONTROL DOOR ASSEMBLIES PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the contract, including general and supplementary conditions and other Division 1

More information

LAYING BLOCK AND BRICK

LAYING BLOCK AND BRICK LAYING BLOCK AND BRICK Products highlighted in this section: SAKRETE Type N Mortar Mix SAKRETE Type S Mortar Mix Brick And Block Laying Basics The first step in building a brick or block wall is to construct

More information

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code

LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900

More information

SECTION VALVE BOXES AND METER VAULTS

SECTION VALVE BOXES AND METER VAULTS SECTION 03 48 20 VALVE BOXES AND METER VAULTS PART 1: GENERAL 1.01 SECTION INCLUDES A. Valve boxes for water and cleanout boxes for wastewater service. B. Meter boxes for water service. C. Meter vaults

More information

Wire Security Partitions & Cages Specification Guide

Wire Security Partitions & Cages Specification Guide Wire Security Partitions & Cages Specification Guide www.cisco-eagle.com/barriers Wire Partitions It doesn t have to be complicated... Cisco-Eagle publishes fully-illustrated, priced fast to order units

More information