OPERATING MANUAL UNIPOWER TELECOM POWER CONTROL & MONITOR SYSTEM PCM500 SERIES

Transcription

1 PRICE: $25.00 UNIPOWER TELECOM POWER CONTROL & MONITOR SYSTEM PCM500 SERIES Manal No. PCM /14/02 PCM500-Man 2002 UNIPOWER Corp. All Rights Reserved UNIPOWER Telecom, Division of UNIPOWER Corporation NORTH AMERICA 3900 Coral Ridge Drive, Coral Springs, Florida 33065, USA Tel: Fax: EUROPE Parkland Bsiness Centre, Chartwell Road, Lancing BN15 8UE, ENGLAND Tel: +44(0) Fax: +44(0)

2 CONTENTS SECTION TOPIC PAGE 1.0 Introdction Featres and Options Safety Warnings Warranty Unpacking and Inspection Specifications Safety and Indstry Standards Front Panel Description Back Panel Description LED Indicators Front Panel Adjstment Potentiometers Description of Operation Connections Alarm Enabling Voltage and Crrent Measrements Battery Temperatre Compensation Installation and Setp Final Installation and Connections 16 Appendix Data Sheet

3 ILLUSTRATIONS FIGURE TITLE PAGE 1 PCM500 Power Control & Monitoring System 2 2 Front and Back Panels of PCM PCM500 Fnctions 8 4 Crrent Measrement Connections 13 5 Test Setp for Setting Battery Overvoltage and Undervoltage 13

4 UNIPOWER TELECOM POWER CONTROL & MONITOR SYSTEM PCM500 SERIES 1.0 INTRODUCTION 1.1 This Operating Manal shold be read throgh careflly before installing and operating the PCM500 Series. 1.2 The PCM500 is a basic control and monitoring system for DC power plants. It controls p to 16 rectifiers in p to 4 shelves, precisely setting the float voltage and eqalize voltage (optional) on all rectifiers simltaneosly. It monitors the battery voltage and crrent by means of front panel test points or optionally by a front panel digital voltmeter and ammeter. See Figre Front panel LEDs indicate stats and alarm conditions of the monitored fnctions. Front panel potentiometers permit easy adjstment of the varios control voltages. Form C relays also indicate stats and alarms. 1.4 The PCM500 is only one monting position high (1.75 inches) to minimize rack space and comes with brackets that permit monting in either a 19- or 23-inch relay rack. It can be monted from the front of the rack with offsets every qarter-inch from front to back to align with existing rack-monted eqipment. 1.5 The PCM500 can be ordered configred for either 24 or 48VDC, either positive or negative plant. It is reverse polarity protected. 2.0 FEATURES AND OPTIONS 2.1 Featres Low Profile: One Monting Position High: (1.75 Inches) 19- or 23-inch Rack Monting 48 or 24VDC Versions Positive or Negative Polarity Plant Reverse Polarity Protected Controls & Monitors Up to 16 Rectifiers in Up to 4 Shelves Centralized Plant Float Voltage Adjst Eight LED Alarm Indicators Eight Form C Relay Contact Alarm Otpts Over & Under Battery Voltage Alarms 1

5 Figre 1. PCM500 Power Control & Monitoring System FRONT VIEW RECTIFIER SHELF CONNECTORS ALARM-ENABLE DIP SWITCHES TB1 CONNECTOR REAR VIEW Figre 2. Front and Back Panels of PCM500 2

6 Compatible with All UNIPOWER Telecom Rectifiers Easy Wire Connections on Rear Alarm Enable Switches on Back Panel 2.2 Options Centralized Plant Eqalize Voltage Adjst Battery Temperatre Compensation (with Temp. Probe) Meter Panel (Voltmeter & Ammeter) 3.0 SAFETY WARNINGS 3.1 This Control and Monitor System operates at voltages that cold potentially be hazardos. Frthermore, inadvertant short circiting of the system battery and/or rectifier by misconnection or other error cold be harmfl. This prodct shold be handled, tested and installed only by qalified technical persons who are trained in the se of power systems and are well aware of the hazards involved. 3.2 When operating the PCM500 the chassis grond terminal mst be connected to the system frame grond or other proper safety grond for the protection of personnel. 3.3 All connections to the PCM500 shold be careflly checked for errors before applying power to it. 3.4 This eqipment is intended only for installation in a RESTRICTED ACCESS LOCATION. 4.0 WARRANTY All prodcts of UNIPOWER Telecom, a division of UNIPOWER Corporation, are warranted for two (2) years from date of shipment against defects in material and workmanship. This warranty does not extend to prodcts which have been opened, altered or repaired by persons other than persons athorized by the manfactrer or to prodcts which become defective de to acts of God, negligence or the failre of cstomer to flly follow instrctions with respect to installation, application or maintenance. This warranty is extended directly by the manfactrer to the byer and is the sole warranty applicable. EXCEPT FOR THE FOREGOING EXPRESS WARRANTY, THE MANUFACTURER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU- LAR PURPOSE. As the sole and exclsive remedy nder this warranty, the manfactrer, at its option, may repair or replace the non-conforming prodct or isse credit, provided the manfactrer s inspection establishes the existence of a defect. To exercise this remedy, the byer mst contact the manfactrer s Cstomer Service Department to obtain a Retrn Material Athorization nmber and shipping instrctions. Prodcts retrned withot prior athorization will be retrned to byer. All prodcts retrned for repair mst be shipped freight prepaid to UNIPOWER. If the byer fails to flly comply with the foregoing, the byer agrees that no other remedy (inclding, bt not limited to, incidental or conseqential damages for lost profits, lost sales, injry to person or property or any other incidental or conseqential losses) shall be available to the byer. 3

7 5.0 UNPACKING AND INSPECTION 5.1 This power control and monitoring system was careflly tested, inspected and packaged for shipment from or factory. Upon receipt of the nit it shold be careflly npacked and inspected for any damage in shipment. 5.2 If there is evidence of damage, do not attempt to install the nit. The freight carrier shold be notified immediately and a claim for the cost of the PCM500 shold be filed with the carrier for direct reimbrsement. Be sre to inclde the model and serial nmber of the damaged nit in all correspondence with the freight carrier. Also save the shipping carton and packing material as evidence of damage for the freight carrier s inspection. 5.3 UNIPOWER Telecom will cooperate flly in case of any shipping damage investigation. 5.4 Always save the packing materials for later se in shipping the nit. Never ship the rectifier system withot proper packing. 6.0 SPECIFICATIONS INPUTS Voltage VDC or 24VDC Nominal Polarity... Positive or Negative Plant Monitoring Inpts... Low Voltage Disconnects 1 & 2... Fse Alarms 1 throgh 5... Battery Voltage & Crrent Metering 2... Temperatre Compensation... Battery Sense... Battery Spply OUTPUTS Control Otpts... Crrent Share... Remote Adjst Alarms, Form C Relay Contacts... EQA = Eqalize... RFA-MIN = Rectifier Failre-Minor... RFA-MAJ = Rectifier Failre-Major... ACFA = AC Failre... FA = Fse or Breaker Failre... LVDA = Low Voltage Disconnect... OVA = Battery Overvoltage... UVA = Battery Undervoltage SAFETY STANDARDS... UL1950, CSA22.2 No.950, EN

8 ENVIRONMENTAL Operating Temperatre Range... 0 C to 50 C Storage Temperatre Range C to +85 C Hmidity... 0% to 95%, Non-Condensing PHYSICAL SPECIFICATIONS Case Material... Steel Finish... Powder Coat Gray Dimensions, Inches (mm) H x W x 9.00 D (44.5 x 483 x 229) Rack Monting Width or 23 Inches NOTES: 1. Model mst be specified for operating voltage. 2. Ammeter reqires an external shnt. 7.0 SAFETY AND INDUSTRY STANDARDS 7.1 The PCM500 Control and Monitor System meets the following safety certifications: STANDARD UL1950 CSA EN AGENCY UL CUL DEMKO 7.2 The PCM500 is CE marked to indicate conformance to the Eropean Union s Low Voltage Directive. 8.0 FRONT PANEL DESCRIPTION 8.1 On the left side of the front panel are the digital voltmeter and digital ammeter. These meters form the option MP and read battery voltage and crrent. The ammeter reqires an external 50mV shnt. See Figre 2 and Section At the center of the panel is a green/red LED alarm which is normally green bt trns red pon failre of the PCM500 Control and Monitor System. 8.3 On the right side are for terminals for reading amperes and volts, the battery crrent and voltage, sing external meters. 8.4 Next, in order, are the voltage adjstment potentiometers VFL, OV, UV, TC and VEQ, whose fnctions are explained in Section Next is the EQ/FL switch for switching the rectifiers between eqalize and 5

9 float voltages. 8.6 Finally, in order, are the LED indicators: RFA-MIN, RFA-MAJ, ACFA, FA, LVDA, OVA and UVA which are explained in Section BACK PANEL DESCRIPTION 9.1 From the left side are the for rectifier connectors J1 throgh J4 which control and monitor the rectifier shelves and individal rectifiers. J1 goes to rectifier shelf no. 1, J2 to shelf no. 2., etc. See Figre In the center of the back panel are the 24 DIP switches which enable the alarms for each rectifier, fse or breaker panel, and low voltage disconnect. Below the switches is the chassis grond terminal. 9.3 On the right side is the TB1 connector with 48 terminals for connecting twowire alarm inpts, alarm otpts and other inpt/otpt connections. These terminals accept AWG nos. 14 to 22 wire sizes LED INDICATORS 10.1 Yellow LED. Indicates controller is in the eqalize voltage mode (option), determined by the front panel Eqalize/Float switch Red LEDs. These are failre alarms indicating the following: Rectifier Failre Alarm-Minor (a single rectifier failre) Rectifier Failre Alarm -Major (two or more rectifier failres) AC Inpt Failre (on any rectifier) Failre on any Fse or Circit Breaker in a distribtion panel Failre on one or both Low Voltage Disconnects Battery Overvoltage Battery Undervoltage 11.0 FRONT PANEL ADJUSTMENT POTENTIOMETERS There are five front panel adjstment potentiometers: VFL: Float Voltage set (12 trns) OV: Battery Overvoltage set (single trn) UV: Battery Undervoltage set (single trn) TC: Temperatre Compensation set (single trn) VEQ: Eqalize Voltage set (single trn) 6

10 Note that Temperatre Compensation and Eqalize Voltage are options that mst be ordered DESCRIPTION OF OPERATION 12.1 See Figre 3. The PCM500 controls and monitors p to for rectifier shelves containing p to for rectifiers each. This is accomplished by means of the for connectors J1 throgh J4 which connect to rectifier shelves one throgh for, respectively. Throgh these connections the PCM500 controls the rectifier otpt voltage which is preset by the VFL (float voltage) and optionally by VEQ (eqalize voltage) adjstment potentiometers. The front panel EQ/FL switch pts the rectifier otpts in either the eqalize or float mode The PCM500 also monitors the AC inpt and DC otpt of each of the rectifiers and gives an LED warning and Form C relay contact alarm in case of failre of any one The PCM500 also monitors for alarms p to two low voltage disconnect panels and p to five fse panels or circit breaker panels. The alarm otpts are Form C relay contacts which can be sed for remote or local system alarms. The PCM500 has inpts from the low-voltage disconnect panels and the fse panels or circit breaker panels Other alarm otpts are for battery overvoltage and battery ndervoltage. These are also Form C relay contacts Battery voltage and crrent are also monitored by the PCM500. They are read either by the optional front panel voltmeter and ammeter or from the front panel test points. An external shnt is reqired for crrent measrement CONNECTIONS 13.1 Rectifier Connections. See Figre 2. Rectifier connections are made to the J1 throgh J4 receptacles, standard 25-pin sbminiatre D connectors (Positronic No. SD25F0S500X with FC7520D pins). The mating plg is a Positronic SD25M0000Z with MC7520D pins. These connectors are identical to and atomatically mate with those on all UNIPOWER Telecom rectifier shelves: Mercry (RMF), Magellan (RMM, RMP), Vangard (RVN) and Ranger (RRS). The table following gives the connections by pin nmber to the rectifier shelves and rectifiers. 7

11 RECTIFIER SHELVES FUSE/CIRCUIT BREAKER PANELS 8 Figre 3. PCM500 Fnctions PCM500 SERIES

12 J1-J4 SIGNAL CONNECTORS PIN FUNCTION 1 NC 2 NC 3 NC 4 NC 5 NC 6 NC 7 NC 8 NC 9 NC 10 Crrent Share 11 + Sense 12 Remote Adjst-2 13 Remote Adjst-4 PIN FUNCTION 14 AC Good-1 15 DC Good-1 16 AC Good-2 17 DC Good-2 18 AC Good-3 19 DC Good-3 20 AC Good-4 21 DC Good-4 22 Signal Common 23 -Sense 24 Remote Adjst-1 25 Remote Adjst-3 J1-J NOTE: J1-J4 Connectors are for rectifier shelves 1-4 respectively. Nmbers following fnctions refer to rectifier modles 1-4 in each shelf. NC=No connection Alarm and Other Inpt/Otpt Connections. See Figre 2. These connections are made to TB1 which is a 48-pin Ero-style terminal block. There are seven alarm inpts (14 terminals), eight Form C relay contact alarm otpts (24 terminals) and 10 terminal connections for other inpt/otpt (I/O) connections. These connections are specified in the tables following. TB1 TERMINAL CONNECTIONS ALARM OUTPUTS ALARM INPUTS OTHER I/O FUNCTION TERM NOS. LVDA1 IN 1 & 48 LVDA2 IN 2 & 47 FA1 IN 3 & 46 FA2 IN 4 & 45 FA3 IN 5 & 44 FA4 IN 6 & 43 FA5 IN 7 & 42 TERM NO. FUNCTION EQA (NC) 13 EQA (C) 14 EQA (NO) 15 OVA (NO) 16 OVA (C) 17 OVA (NC) 18 RFA-MIN (NO) 19 RFA-MIN (C) 20 RFA-MIN (NC) 21 LVDA (NO) 22 LVDA (C) 23 LVDA (NC) 24 TERM NO. FUNCTION FA (NC) 25 FA (C) 26 FA (NO) 27 ACFA (NC) 28 ACFA (C) 29 ACFA (NO) 30 RFA-MAJ (NC) 31 RFA-MAJ (C) 32 RFA-MAJ (NO) 33 UVA (NC) 34 UVA (C) 35 UVA (NO) 36 TERM FUNCTION NOS. I+ (IN) 41 I- (IN) 8 TC (IN) 9 & 40 B+ (IN) 10 B- (IN) 11 CS (OUT) 12 BS+ (IN) 39 BS- (IN) 38 RA (OUT) 37 Inpts on terminals 1-7 and are from relay contacts on low voltage disconnect panels and fse/breaker panels. An open at these terminals indicates an alarm. 9

13 Otpts on terminals are Form C relay contact alarms for the fnctions given. Normally Closed (NC) means a short between this terminal and the Common (C) terminal when the fnction is operating properly with power applied. Normally Open (NO) means an open between this terminal and the Common (C) terminal when the fnction is operating properly with power applied Abbreviations/Acronyms. These are sed in the previos tables and are defined in the following table. ACRONYM DESCRIPTION LVDA Low Voltage Disconnect Alarm FA Fse/Circit Breaker Alarm I+, I- Meter Shnt TC Temperatre Compensation (from probe) B+, B- Battery (from rectifier bs) CS Crrent Share (to rectifier shelves) EQA Eqalize Alarm OVA Battery Overvoltage Alarm RFA-MIN Rectifier Failre Alarm - Minor (single rectifier failre) ACFA AC Failre Alarm RFA-MAJ Rectifier Failre Alarm - Major (two or more rectifier failres) UVA Battery Undervoltage Alarm RA Remote Adjst (to rectifier shelves) BS+, BS- Battery Sense 13.4 Explanation of Other I/O Connections. Most of the connections to TB1 are alarm inpts and otpts. The Other I/O connections are varios analog type connections I+ and I- Inpt. These are the + and - connections from a meter shnt that is sed to measre battery crrent. See Section 15.3 on Crrent for frther details TC Inpt. This is the optional temperatre compensation inpt from the temperatre compensation probe that comes with this option. The probe is sed to measre battery temperatre which is sed to control the otpt of the rectifier. See Section 16.0 on Battery Temperatre Compensation. There is no polarity reference on this B+ and B- Inpt. These connections are to the common rectifier otpt bs which is sed to provide power to operate the PCM500 10

14 circitry CS Otpt. This is the crrent share connection to the for rectifier shelves and is sed only if additional rectifier shelves are added to the system ALARM ENABLING BS+ and BS- Inpts. These are battery sense inpts to PCM500 and are connected to the common rectifier bs near the battery bt on the rectifier side of any battery disconnect or LVD circit Alarm-Enable Switches. These switches are located at the center of the back panel. As shown following there are for colmns with six each DIP switches. The colmns and rows are nmbered. SWITCH NO. POSITION NO. Each switch controls one of the alarm fnctions. The PCM500 comes with all alarm fnctions disabled, with the switches in the left position. Moving a switch to the right enables that fnction Alarm Fnctions. There are 24 separate alarm fnctions controlled by the Alarm-Enable switches. Only those fnctions sed shold be enabled; otherwise false alarms will be created. The first 16 fnctions are rectifier/alarms. Provision is made for shelf nmber and rectifier nmber for p to for shelves with p to for rectifiers each. SR stands for shelf/rectifier. As shown in the following table the shelf no. and rectifier no. correspond to the switch no. and position no., respectively. Ths switch no. 2, postion no. 3 (2,3) enables the shelf no. 2, rectifier no. 3 alarm (SR23). When the proper rectifier alarmenable switches are set, if any one rectifier fails the RFA-MIN (Rectifier Failre-Minor) red LED will come on, and the RFA-MIN Form C relay will change state. If more than one rectifier fails the RFA-MAJ (Rectifier Failre- Major) red LED will come on and the RFA-MAJ Form C relay will change state. 11

15 ALARM-ENABLE DIP SWITCHES POS. SW. NO.1 SW. NO.2 SW. NO.3 SW. NO.4 NO. FUNCTION FUNCTION FUNCTION FUNCTION 1 SR11 SR21 SR31 SR41 2 SR12 SR22 SR32 SR42 3 SR13 SR23 SR33 SR43 4 SR14 SR24 SR34 SR44 5 FA1 FA3 FA5 LVDA1 6 FA2 FA4 NC LVDA2 The FA1 throgh FA5 alarms fnction for p to five fse or circit breaker distribtion panels. If any fse or circit breaker on any panel opens, this will case the FA (Fse or Circit Breaker Alarm) red LED to come on and the FA Form C relay to change state. The LVDA1 and LVDA2 alarm-enable switches are for one or two Low Voltage Disconnect panels. If either one of these experience a disconnect, the LVDA (Low Voltage Disconnect Alarm) red LED will come on and the LVDA Form C relay will change state VOLTAGE AND CURRENT MEASUREMENTS 15.1 Meters and Test Points. The meter panel option (Option MP) provides a digital voltmeter and ammeter on the left front panel to monitor the battery voltage and crrent Voltage. The digital voltmeter reads battery voltage directly, to tenths of a volt. The volts test points on the right front panel also permit direct external measrement of the battery voltage when the MP option is not taken Crrent. The digital ammeter is scaled at the factory to read amperes based on a 50 millivolt external shnt and corresponding internal scale factor which mst be chosen at the time of ordering. The following table gives the ammeter shnt rating and ordering sffix code for the correct meter setting at the factory. The external shnt mst be connected with correct polarity across the I+ and I- inpt terminals (TB1 terminals 41 and 8, respectively). See Figre 4 and Section External 50mV Shnt CODE AMMETER SHUNT RATING 25 25A 30 30A 50 50A 75 75A A A A CODE AMMETER SHUNT RATING A A A A A A 12

16 Figre 4. Crrent Measrement Connections Figre 5. Test Setp for Setting Battery Overvoltage and Undervoltage 13

17 This table shows that, for example, a 50mV, 100A shnt is the shnt resistance that prodces 50mV for a 100A fll-scale crrent. In this case the shnt resistance is 50mV 100, or 0.5 milliohm. The shnt rating is always the fll-scale crrent that prodces 50mV across the shnt. The 3 ½ digit ammeter resolves crrent readings to 0.1A over the 25A to 200A fll-scale range. From 250A to 2000A fll scale, the meter resolves crrent to the nearest ampere. Overall accracy is moderate, generally within ±5%. Crrent may also be measred at the AMPS test points by sing a 50mV fll scale voltmeter. The external shnt mst be also sed for this measrement. The actal crrent mst then be determined by mltiplying the meter reading in millivolts by the fll scale shnt crrent divided by BATTERY TEMPERATURE COMPENSATION 16.1 The temperatre compensation option (Option TC) comes with a temperatre probe and 20-foot cable. The probe is a thermistor which is connected to TB1 pins 9 and 40. There is no polarity for this connection. The probe is sed to monitor the temperatre of the battery and adjst the rectifier otpt voltage accordingly. As battery temperatre increases, rectifier otpt voltage decreases The change in otpt voltage with temperatre is -3mV/ºC per battery cell, centered at 25ºC. For example, for a +10ºC temperatre change from 25ºC with the rectifier charging a 48V battery, the change in the rectifier otpt voltage wold be: 48 2 = 24 cells rv = 24 cells x 10ºC change x (-3mV) = -720mV = -0.72V 16.3 The probe can be located in several possible places: right on the battery to detect the battery temperatre; near the battery in free air to detect the local ambient temperatre; or on the power plant metal frame near the battery. For the procedre on calibrating this temperatre compensation system, see Section If the TC probe is either opened or shorted, the rectifier otpts revert to the float voltage. 14

18 17.0 INSTALLATION AND SETUP 17.1 Monting. The PCM500 can be monted in either 19- or 23-inch racks by sing the appropriate brackets. Mont it from the front of the rack sing the correct offsets to align with existing rack-monted eqipment. The bracket offsets are every qarter-inch from front to back Setting the Battery Overvoltage. Set a 0-60VDC precision power sorce or variable DC power spply with an otpt voltmeter to approximately 55V. Trn the spply off and connect it to the PCM500 TB1 terminals as shown in Figre 4. Trn the power spply back on and set the otpt voltage to the desired voltage for the battery overvoltage alarm. Then adjst the front panel OV potentiometer to the trip point where the OVA (overvoltage alarm) red LED jst barely trns on Setting the Battery Undervoltage. Using the same setp, set the 0-60V spply to the desired voltage for the ndervoltage alarm. Adjst the front panel UV potentiometer to the trip point where the UVA (ndervoltage alarm) red LED jst trns on. Trn off the 0-60V spply and disconnect it Setting the Battery Float Voltage. Connect a single rectifier to the PCM500 by means of J1. Set the front panel EQ/FL switch to FL (float, down position). Connect the B+ inpt (TB1 term. 10) and BS+ inpt (TB1 term. 39) to the rectifier positive otpt. Connect the B- inpt (TB1 term. 11) and BSinpt (TB1 term. 38) to the rectifier negative otpt. Trn on the rectifier and read the rectifier otpt voltage on the front panel voltmeter (option) or digital voltmeter connected to the volts test points. Adjst the VFL (float voltage) mlti-trn potentiometer to the desired float voltage as read on the voltmeter Setting the Battery Eqalize Voltage (Option). Contining from above, set the EQ/FL switch to EQ (eqalize, p position). The EQA (eqalize alarm) yellow LED shold trn on. Adjst the VEQ (eqalize voltage) potentiometer to the desired eqalize voltage as read on the voltmeter Setting the Temperatre Compensation Voltage (Option) Make sre that the float voltage was set with the temperatre probe disconnected Before connecting the temperatre probe, record the float voltage to three digits. 15

19 Connect the temperatre probe to terminals 9 and 40 of TB With the temperatre probe at approximately 25ºC ambient temperatre, adjst the front panel TC potentiometer ntil the rectifier otpt voltage as read on the front panel voltmeter or external voltmeter is exactly the same as the previosly recorded float voltage Checking the Alarm Fnctions. With the above rectifier connected to the Shelf 1, Rectifier 1 position, check the alarm fnctions as follows Move the SR11 Alarm-Enable DIP Switch to the enable (right) position. The red LED alarm shold not trn on Move the SR22 rectifier DIP switch to the enable (right) position. The RFA-MIN (rectifier failre alarm-minor) red LED shold trn on; the ACFA (AC failre alarm) red LED shold also trn on. Move the SR22 switch back to disable (left). Move the SR33 DIP switch to the enable position. The RFA-MIN and ACFA red LEDs shold again trn on. Move the SR44 DIP switch to the enable position. The RFA-MAJ (rectifier failre alarm-major) red LED shold trn on and ACFA red LED shold remain on. The RFA- MIN red LED shold trn off Move the FA1 (fse/circit breaker alarm) DIP switch to the enable position. The FA red LED shold trn on Move the LVDA1 (low-voltage disconnect alarm) DIP switch to the enable positon. The LVDA red LED shold trn on Move all DIP switches back to their disable (left) positions FINAL INSTALLATION AND CONNECTIONS 18.1 To complete the installation, the following connections mst be made. Do these with the rectifier(s) off and no connection to the battery yet Connect the rectifier shelves to be sed to the J1 to J4 connectors on the back of the PCM500. Use p the positions in seqence, one throgh for. Likewise, fill the shelves with rectifiers in seqence, leaving any blanks at the end of the seqence. All UNIPOWER Telecom rectifier connections are 16

20 compatible with the PCM500 J1-J4 connectors. Compatible cables are available from UNIPOWER Telecom; contact the factory. If another manfactrer s rectifiers and shelves are sed, they mst be properly connected, pin for pin, to be compatible with J1-J4 as shown in the Signal Connectors table. The AC Good and DC Good fnctions mst give a TTL HI or Open for a falt, and the remote adjst inpt range mst fall within 0V to +5V Set the appropriate Alarm-Enable DIP switches to the enable (right) position for the alarm fnctions sed. All others mst remain in the disable (left) position Make all the Alarm Inpt connections to TB1 from the fse/circit breaker panels and the low-voltage disconnect panels. These inpts mst be normally closed bt go to an open for an alarm condition. Nmbers 14 to 22 AWG wire size may be sed on all TB1 terminals Make all Alarm Otpt connections to TB1 for the alarm fnctions sed. These connections (terminals 13-36) are Form C relay otpts. Normally Closed (NC) means a short between this terminal and the common (C) terminal when the fnction is operating properly with power applied. Normally Open (NO) means an open between this terminal and the Common (C) terminal when the fnction is operating properly with power applied. The only exception to this is the EQA (eqalize alarm) fnction; this fnction is defined as Normal when the EQ/FL switch is in the FL (float) position. An alarm is created when the switch is in the EQ (eqalize) position; the EQA yellow LED also trns on Determine which side of the shnt goes to the battery floating terminal. Do not connect to battery yet. Connect leads from each side of the shnt, with proper polarity, to the TB1 shnt inpt terminals, I+ and I- (terminals 41 and 8 respectively) If the battery temperatre compensation is sed, connect the leads from the probe to TB1 TC terminals 9 and 40. There is no polarity to this connection. The probe shold be installed on or near the battery as discssed in Section With the rectifiers still off, connect the B+ and B- inpts to TB1 (terminals 10 and 11 respectively) to the positive and negative common rectifier distribtion bses. 17

21 18.9 Connect the BS+ and BS- (battery sense) inpts to (TB1 terminals 39 and 38 respectively) to the positive and negative sides of the battery, bt on the rectifier side of any battery disconnects or circit breakers The PCM500 is now ready to operate. The shnt shold now be connected to the battery. After this is done the rectifier shelves shold be trned on. 18