LITHIUM BALANCE CHARGER
|
|
- Maryann Sims
- 7 years ago
- Views:
Transcription
1 LITHIUM BALANCE CHARGER A Microprocessor controlled, high-performance charger for NiCd/NiMH/LiPo/Pb batteries with an integral individual voltage balancer (LiPo only) Operating Manual Please read this entire operating manual completely and carefully, as it contains a wide variety of specific programming and safety information. The selection of the correct operating parameters is the responsibility of the user. Keep this manual in a safe place, and be sure to pass it on to the new owner if you ever sell your Cavalier EQ.
2 Special Features Voltage Balancer for LiPo Batteries The Cavalier EQ has an individual cell voltage balancer internally so there is no need for a separate balancer when charging a LiPo battery pack. Delta-Peak Sensitivity The automatic charge termination program works on the principle of the Delta-peak voltage detection. Capacity Limit: The charging capacity is always calculated by multiplying the charging current by the time. If the charging capacity exceeds the limit, the process will be terminated automatically when you set the maximum value. Temperature Limit (*): The temperature of the battery while charging will rise because of its internal chemical reaction.if you set the temperature limit, the charging process will be terminated when the limit has been reached. This function requires the use of the optional Temperature Sensor. Processing Time Limit: You can also restrict the maximum process time to help protect against a possible defects in the battery pack. Input Power Monitor: When using a 12v car battery as the primary input power for the charger, the charger will monitor its voltage and shut off if the voltage from the car battery if it becomes too low. This is to protect against your car battery being overdischarged and not having enough power to start your car. High- Power and High Performance Circuit: The Cavalier EQ employs a circuit that has a maximum output power of 50W. As a result, it can charge up to 14 cells of NiCd/NiMH and 5 series of LiPo batteries with a maximum current of 5.0A. The current will be automatically reduced if the 50W limit is exceeded. Specifications: Operating voltage range: Circuit power: Charge current range: Current drain for balancing LiPo: NiCd/NiMH battery cell count: Lithium/Polymer cell count: Pb battery voltage: Weight: Dimensions: Volt Max. 50W A 200mAh/cell 1-14 cell 1-5 Series 2 to 12V 360g 130 x 90 x 30 mm - 1 -
3 Exterior of the unit Input Power Cable Temp Sensor LCD Screen 16 Characters, 2 lines Output charge lead 4mm sockets Balance lead sockets Temp. DC 11-18V Sensor DC 11-18V LITHIUM BALANCE CHARGER USER SET PROGRAM-> INTELLIGENT DIGITAL BALANCE CHARGER Li-Po 1~5 cells Ni-MH/NiCd 1~14 cells Lead Acid (Pb) 2~12v Charge Rate 0.1~5.0A 4 CELLS 2 CELLS 3 CELLS 5 CELLS BALANCE CHARGING SOCKET OUTPUT+ Battery Type Status Stop Decrease Increase Start Enter Scroll through the Main Menu Stop any charge processes Alter values - See the status of individual cells in balance charge mode Scroll through the Main Menu Start any charge processes POWER SUPPLY THE TEMP SENSOR SYSTEM The Pro-Peak Cavalier EQ comes with 4mm banana plugs and detachable crocodile clips for direct DC battery connection, or you can use the 11-18v socket for mains power adapter. This device can protect your batteries effectively. (Optional part) - 2 -
4 Warnings and safety notes Never leave the charger unsupervised when it is connected to its power supply. If any malfunction is observed, immediately terminate the process and refer to the operation manual. Keep the unit away from dust, damp, rain, heat, direct sunlight and vibration. Do not drop it. The circuit of the Cavalier EQ is designed to be powered by a 10-18V DC only. The Cavalier EQ and the battery that it is charging should be set up on a heat-resistant, non-flammable and non-conductive surface. Never place them on a car seat, carpet or similar surface. Keep all flammable and volatile materials well away from operating area. Be sure to understand the charging information of the battery to be charged so that it can be done accurately. If the program is set up incorrectly, the battery can be severely damaged. Use extra caution with Lithium batteries as a fire or an explosion can occur by over-charging or selecting the incorrect charging program. To avoid short-circuits between the charge leads, always connect the charge cable to the unit first and then to the battery to be charged. Reverse the sequence when disconnecting. Do not connect more than one battery pack to the charge lead at any one time. Do not attempt to charge or discharge the following types of batteries: - Battery packs which consist of different types of cells (including different manufacturers). - A battery which is already fully charged or just slightly discharged. - Non-rechargeable batteries (Explosion hazard). - Batteries that require a different charge technique from NiCd, NiMH, LiPo or Pb. - A faulty or damaged battery. - A battery fitted with an integral charge circuit or a protection circuit. - Batteries installed in a device, or which are electrically linked to other components. - Batteries that are not expressly stated by the manufacturer to be suitable for the currents the charger delivers during the charge process. Please double check the following points before beginning the charge operation. - Did you select the appropriate program that is suitable for the type of battery you are charging? - Did you set up the correct current for charging? - Lithium battery packs can be comprised with parallel and series circuits mixed Please check the composition of the battery pack carefully before charging. - Are all connections firm and safe? Is there an intermittent contact at any point in the circuit? These warnings and safety notes are particularly important. Please follow the instructions for maximum safety. If these instructions are not followed correctly, the charger and/or battery can be damaged, bodily injury can occur and fire and/or loss of property can also occur
5 Program flow chart - 4 -
6 Initial Parameter set up The Pro-Peak Cavalier EQ will be set up with default values for the essential user settings when it is connected to a 12V battery for the first time. The screen displays the following information in sequence and you can change the value of the parameters on each screen. If you wish to alter the parameter value in the program, press the start enter key to make it flash, then change the value with the DEC or INC key. Save the parameter value by pressing the Start Enter key once more. USER SET - This confirms that you are in the overall parameters section. Press the Start Enter button to access the parameters and then the DEC or INC buttons to select the individual parameter you require. Press the Start Enter button to select each parameter value in turn and adjust that value with the DEC or INC buttons. Move on to the next parameter using the DEC or INC buttons. To return to the USER SET screen at any time, press the Batt Type Stop button. TEMP CUT OFF - This feature uses the optional temperature probe to contact the surface of battery, the temperature cut-off can be on or off. If it is to On, set the maximum temperature at which the charger should allow the battery to reach during charging.once a battery reaches this temperature, the process will be terminated to protect the battery. SAFETY TIMER - When you start a charge process, the integral safety timer automatically starts running at the same time. This is programmed to prevent overcharge of the battery if it proves to be faulty, or if the termination circuit cannot detect if the battery is full. The value for the safety timer should be generous enough to allow a full charge of the battery. CAPACITY CUT OFF - This program sets the maximum charge capacity that will be supplied to the battery during charge. If the delta-peak voltage is not detected or the safety timer expired for any reason, this feature will automatically stop the process at the selected capacity value. KEY BEEP - A beep will sound every time a button is pressed to confirm your action. A beep will sound at various times during operation to alter different mode changes. These sounds can be turned on or off. INPUT POWER LOW - This program monitors the voltage of the input battery. If the voltage drops below the value you set, the operation will be terminated to protect the source battery. BACK LIGHT - You can adjust the brightness of the LCD screen to suit your preference
7 Lithium Polymer Battery Program These programs are only suitable for charging and discharging Lithium-Polymer batteries with a nominal voltage of 3.7V per cell. These batteries need to adopt different charge techniques and are termed a constant voltage (CV) and constant current (CC) method. The charge current is selected according to the battery capacity, and is usually C/2 rate (half capacity as a charge current). The charge current is not automatically limited in any way so you must select the correct value for your battery. It is not recommended to exceed a 1C charge unless your battery is specifically designed for it. The final voltage of the charge process is also very important. It should be 4.2V/cell for the nominal voltage of 3.7V/cell. If the final voltage exceeds 4.2V you may be risking the chance of fire or explosion of the battery. With the correct settings and a battery in good condition, this is automatically controlled during balancing. It is important to set the correct LiPo program (number of cells in the pack and current) before you begin charging. If you want to alter the parameter value in the program, press Start Enter key to make it flash and then change the value with DEC or INC key. The value can be stored by pressing Start Enter key once more. Charging a LiPo Battery (No Balancing) The value on the left side of the second line sets a charge current. The value on the right side of the second line sets the voltage of the battery pack to be charged. Press Start Enter to select the parameter and then change the value with the INC or DEC buttons. Select the correct values for your battery pack and then press the Start Enter button and hold for more than 3 seconds This shows the number of cells you set up and that the processor detects. R: shows the number of cells found by the charger and S: is the number of cells selected by you on the previous screen. If both numbers are identical, you can start charging by pressing the Start Enter button again. If not, press the Batt Type Stop button to go back to the previous screen. Then, carefully re-check the number of cells of the battery pack to charge. This screen shows the present situation during the charge process. To stop charging, press the Batt Type Stop key once. Charging a LiPo Battery (With Balancing) This is for balancing the voltages of Lithium Polymer cells within a battery pack for optimum performance and battery life. To do this, the battery pack being charged should have a balance plug to connect to the appropriate socket in the charger. If you don t have a JST XH style connector on your battery, you can use an adapter board. One for Impulse (later plugs), FlightPower and Thunder Power is included together with a connecting lead. The connecting lead uses the 5 cell socket in the charger. Other types of adapter board are available as optional extras. You must also connect the main battery leads to the output sockets (4mm) of the charger for this program. In this mode, the charging process will be different from the ordinary LiPo charging mode. The internal processor of the charger will monitor the voltages of each cell in the battery pack and control the charge current feeding to each cell to equalize the voltages
8 The value on the left side of the second line sets a charge current and the value on the right side of the second line sets the voltage of the battery pack. After setting the current and voltage, press the Start Enter key and hold for more than 3 seconds to start the process.(charge current: a,voltage: 1-5series) This allows you to confirm the settings you selected. The processor detects. R: the number of cells found by the charger and S: the number of cells selected by you at the previous screen. If both numbers are identical, you can start charging by pressing the Start Enter button. If not, press the Start Type Stop button to go back to the previous screen. Carefully re-check the number of cells of the battery pack to charge. This screen shows the current status of the battery pack while it charges. To stop charging, press the Batt type Stop key once. Initial Parameter set up You can monitor the present voltage of an individual cell by pressing DEC or INC button during the charge process. The first line of display shows the voltage of cell no.1, no.2 cell and no.3 cell from the left. And the left of second line shows the charging current, then the voltage of no.4 and no.5 cell. WARNING! When charging LiPo battery in balancing mode. It will damage the charger if you connect your battery with the Cavalier EQ incorrectly. Please connect as shown in the following images carefully. Direct Connection With Adapter Board - 7 -
9 NiMH/NiCd Battery Charging Program Please note that this program is only for NiMH or NiCD batteries associated with R/C model applications. Do not try to charge any other type of battery using this program. This program simply charges the battery using the current you set, the charge current ranges from 0.1A to 5A. Select this charge process by choosing NiMH or NiCD charge from the main menu by pressing the Start/Enter button. The display should look similar to this. If you need to alter the charge current press the Start/Enter button to make it flash, then change the value with DEC or INC buttons. The value will be stored by pressing the Start/Enter button. Once the setting is correct, press and hold the Start/Enter button for 3 seconds to begin the charge process. The display will now show the following. The charger will emit a sound to inform you when the charge process is finished. To finish early, press the Batt type/ Stop button. Pb (Lead-Sulphuric Acid) Battery Charging Program This program is for charging Pb(lead-acid) batteries with a nominal voltage from 2 to 12V. Pb batteries are totally different from NiCd or NiMH batteries. They can only deliver relatively low current compared to their capacity, and similar restrictions definitely apply to charging. The optimal charge current will be 1/10th of the capacity. Pb batteries must not be charged rapidly. Always follow the instructions that are supplied by the manufacturer of the battery. Set up the charge current on the left and the nominal voltage of the battery on the right. The charge current can range from 0.1 to 5.0A and the voltage should match with the battery being charged. Start the charge process by pressing the Start Enter key for more than 3 seconds. The screen displays the state of the charging process. To stop charging, press the Batt type Stop key once. The sound indicates you have ended the process
10 Warning and error messages The Cavalier EQ incorporates various functions for protection and monitoring of the system to verify things are working properly. In the case of an error occurring, the screen will display the cause of the error accompanied by a beeping sound. REVERSED POLARITY - The output is connected to a battery with incorrect polarity. CONNECTION BREAK - This will be displayed in the event that an interruption is detected in the connection between the battery and output or voluntarily disconnection the charge lead during the charging operation or discharge on output. SHOT ERR - There was a short-circuit at the OUTPUT side. In Voltage ERR - The voltage of the input power source has dropped to an unsafe level. VOL SELECT ERR - The voltage of the Lithium battery pack was selected incorrectly. Verify the voltage of battery pack carefully. BREAK DOWN If there happens to be a malfunction of the unit for any reason. BATTERY CHECK LOW VOLTAGE - The processor detects the voltage difference during charging. BATTERY CHECK OVER VOLTAGE - The processor detects the voltage difference during charging BATTERY VOL ERROR - The voltage of one of the cells in the LiPoly battery pack has raised over the limit. Warranty and Service We warrant this product for a period of one year (12 months) from the date of purchase. The guarantee applies only to material or operational defects which are present at the time of purchase or arise as a result of manufacturing fault. During that period, we will repair or replace without service charge any product deemed defective due to those causes. You will be required to present proof of purchase (invoice or receipt). This warranty does not cover any damage due to wear, overloading, incompetent handling or use of incorrect accessories
11 Optional Items Temperature Sensor Part No: O-IPTS1 Balancer Adapter Board for JST EH plugs (Graupner, Robbe, Kokam etc) Part No: O-IPBAL-ABEH Balance Adapter Board for SMH-250 plugs (Polyquest, Hyperion, old Impulse) Part No: O-IPBAL-ABPQ
12 LITHIUM BALANCE CHARGER Distributed by Ripmax Ltd, 241 Green Street, Enfield, EN3 7SJ. United Kingdom.
INTRODUCTION INTRODUCTION
B6AC TABLE OF CONTENTS INTRODUCTION...1 SPECIAL FEATURES...2 SPECIFICATIONS...5 LITHIUM POLYMER BALANCE CHARGE PROGRAM CONNECTION DIAGRAM...6 WARNING AND SAFETY NOTES...7 PROGRAM FLOW CHART...12 INITIAL
More informationG.T. POWER V5 BALANCE CHARGER FOR NICD/NIMH/LITHIUM/PB BATTERIES
G.T. POWER V5 BALANCE CHARGER FOR NICD/NIMH/LITHIUM/PB BATTERIES Thank you for purchasing G.T. Power V5 Charger. This is a rapid charger with build-in balancer, computerised with microprocessor and specialised
More informationOverlander RC-6S Pro User s Manual
Overlander RC-6S Pro User s Manual A Digital Programmable Balancing Charger/Discharger/Cycler. http://www.overlander.com 1 Contents. Page No. Introduction. 1 Specification. 1 Special Features. 1 Charger
More informationOPERATING MANUAL. 4 Ports Output. Balance Charger/Discharger For LiPo/LiFe/LiIon/NiMH/NiCd/Pb Batteries
OPERATING MANUAL 4 Ports Output Balance Charger/Discharger For LiPo/LiFe/LiIon/NiMH/NiCd/Pb Batteries TABLE OF CONTENTS 1. Features... 2 2. Exterior of the unit... 4 3. Warnings and safety notes... 5 4.
More informationFAILURE TO FOLLOW THESE WARNINGS CAN BE CONSIDERED NEGLI- GENCE BY THE OPERATOR AND MAY NEGATE ANY CLAIMS FOR DAM- AGES INCURRED.
INSTRUCTION MANUAL Table of contents Introduction Introduction... 3 Parts Layout... 4 Specifications and Charger Layout... 5 Features... 6 Warnings and Safety Notes... 9 Power Supply Connections... 12
More informationHYPERION EOS0606i-B USER S MANUAL Visit for the newest manuals and news
HYPERION EOS0606i-B USER S MANUAL Visit http://media.hyperion.hk/dn/eos for the newest manuals and news EOS 0606i Special Features (rev B ) *Powerful, yet compact and portable with wide support for battery
More informationHyperion EOS-0610iNET Charger - User s Manual Visit http://media.hyperion.hk/dn/eos for the newest manuals and news
Hyperion EOS-0610iNET Charger - User s Manual Visit http://media.hyperion.hk/dn/eos for the newest manuals and news Specifications: Charges 1 to 6 cells Lithium Polymer Batteries (3.7V/cell nominal types)
More informationHyperion EOS-0610iDUO Charger - User s Manual Visit http://media.hyperion.hk/dn/eos for the newest manuals and news
Hyperion EOS-0610iDUO Charger - User s Manual Visit http://media.hyperion.hk/dn/eos for the newest manuals and news Specifications: Charges 1 to 6 cells Lithium Polymer Batteries (3.7V/cell nominal types)
More information12 Volt 30 Amp Digital Solar Charge Controller
12 Volt 30 Amp Digital Solar Charge Controller User s Manual WARNING Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationMini Power Bank and Charger
Mini Power Bank and Charger Owner s Manual Please read before using this equipment. Your charger is ETL listed to UL standards and meets all applicable FCC standards. WARNING: To reduce the risk of fire
More informationPOWER B OX Battery. Operating Instructions
POWER B OX Battery Operating Instructions PowerBox Battery 2800 2800 mah / 7.4 Volt Order No: 2810 JR / Futaba Order No: 2820 PowerBox green connectors Dear Customer, We are delighted that you have decided
More informationUSER MANUAL. EZRUN Series Brushless Speed Controller EZRUN-150A-PRO
USER MANUAL EZRUN Series Brushless Speed Controller EZRUN-150A-PRO User Manual of EZRUN-150A-PRO Brushless ESC HW-SM405ENG-20130809 Page - 1 - Declaration Thanks for purchasing our Electronic Speed Controller
More informationwww.ringautomotive.co.uk Instructions: Retain these instructions for future reference SmartChargePro35 RSCPR35-12v, 2 / 8 / 16 / 35A
SmartChargePro7 RSCPR7-12v, 7A SmartChargePro10 RSCPR10-12v, 10A SmartChargePro15 RSCPR15-12v, 15A SmartChargePro25 RSCPR25-12v, 2 / 6 / 12 / 25A SmartChargePro35 RSCPR35-12v, 2 / 8 / 16 / 35A SmartChargePro50
More informationSolar Controller / Battery Charger User s Manual
Solar Controller / Battery Charger User s Manual 1 Congratulations! You have made an excellent choice by purchasing this high quality KORR PWM solar controller which has been manufactured to the highest
More informationQUICK PROBLEM SOLVING GUIDE
QUICK PROBLEM SOLVING GUIDE CTEK battery chargers are extremely reliable. Most fault s are a result of battery issues rather than the charger itself. Using this guide will help you to identify common problems
More informationA IT IS HIGHLY RECOMMENDED THAT YOU UTILIZE A SAFETY DEVICE SUCH A IT IS HIGHLY RECOMMENDED THAT YOU KEEP AN OPERABLE CLASS A FIRE.
INSTRUCTION MANUAL WARNING: THE CHARGING AND DISCHARGING OF RC HOBBY BATTERIES CAN BE DANGEROUS. FAILURE TO FOLLOW THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL MAY RESULT IN PROPERTY DAMAGE AND/OR LOSS
More informationGetting started with the Super Brain Palm computer interface.
Getting started with the Super Brain Palm computer interface. Step 1: Connect the RB502 interface cable to your Super Brain Palm Charger. Step 2: Connect the USB interface to your computers USB port. Step
More informationManaging A123 Cells with FMA Cell Balancing Technologies
Managing A123 Cells with FMA Cell Balancing Technologies By FMA Staff Latest revision: March 23, 2007 Document provided by FMA, Inc. 5716A Industry Lane Frederick, MD 21704 U.S.A. Phone: (800) 343-2934
More information13 Watt PORTABLE SOLAR POWER KIT
3 Watt PORTABLE SOLAR POWER KIT User s Manual Thank you for purchasing a Sunforce Portable Solar Power Kit. Please read these instructions carefully and thoroughly before using the product. Your new Portable
More informationUser Manual for CH-PFC76810
AA Portable Power Corp www.batteryspace.com, Email: Sales@batteryspace.com User Manual for CH-PFC76810 1. Overview The CH-PFC76810 charger is suitable for charging lithium ion battery packs such as those
More information3000W Power Inverter
3000W Power Inverter OWNER S MANUAL Model number-4573000 TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE
More informationLS1024B / LS2024B/ LS3024B. Solar Charge Controller USER MANUAL
EPSOLAR LS1024B / LS2024B/ LS3024B Solar Charge Controller USER MANUAL Thank you very much for selecting our product! This manual offers important information and suggestions with respect to installation,
More informationINSTRUCTION MANUAL INDEX
DTXP4245 INSTRUCTION MANUAL The Onyx 245 charger is two chargers in one! Identical twin outputs make the 245 an excellent choice for models that use two battery packs or modelers who rotate through multiple
More informationOperating Instructions
Operating Instructions Dear customer, Congratulations on your decision to purchase the Smart-Switch from our range! This innovative product is the world s first electronic multi-function switch system,
More informationSHENZHEN JUNSI ELECTRONIC CO.,LTD
Cell Voltage Monitor&Logger USER S MANUAL SHENZHEN JUNSI ELECTRONIC CO.,LTD Thank you for purchasing the. Please read the entire User s Manual completely and attentively as it contains a wide variety of
More informationAmps Per Bank. Total Output. Battery System. Model Name. 6 amps 12 amps 10 amps 20 amps 30 amps 40 amps 15 amps 30 amps 45 amps
Model Name Total Output Amps Per Bank Battery System Pro XL Dual Pro XL Pro SE Dual Pro SE Three Bank Pro SE Four Bank Pro SE Pro Charger Dual Pro Charger Three Bank Pro Charger 6 amps 12 amps 10 amps
More informationAutomatic taper of charge rate for superior battery life through good equalization of cells and low water use rate.
*00151* FEATURES Automatic taper of charge rate for superior battery life through good equalization of cells and low water use rate. Silicon diodes with inherent surge protection operated at a conservative
More informationBUB-110B. Portable Power Pack. Compact USB Battery Charger for up to 5 Smartphones and Mobile Devices. User Manual
BUB-110B High Capacity Portable Power Pack Compact USB Battery Charger for up to 5 Smartphones and Mobile Devices User Manual 2 Welcome Thank you for choosing Xuma. Congratulations on the purchase of your
More informationInstallation and Operation Manual. Digital Remote Meter for Monitoring System Performance. Version: RM-1
REMOTE METER TM Installation and Operation Manual. Digital Remote Meter for Monitoring System Performance. Version: RM-1 1098 Washington Crossing Road Washington Crossing, PA 18977 USA www.morningstarcorp.com
More informationBosch C3 and C7 Battery Chargers: Smart, safe and simple to use
Bosch C3 and C7 Battery Chargers: Smart, safe and simple to use The smart charger for many applications Did you know? The intelligent characteristics of the Bosch C3 and C7 battery chargers enable them
More informationuser s manual Battery Case model #: SPB3200 Battery Case Charger for Samsung Galaxy S 4
user s manual model #: SPB3200 Charger for Samsung Galaxy S 4 What s Included Unpack the battery case and make sure all accessories are put aside so they will not be lost. hello. USB to Micro USB Cable
More informationPhoenixtech Brushless Motor Speed Controller Programming Guide
Congratulations on the purchase of your new Phoenixtech Brushless Motor Speed Controller. This latest series of controllers is unique in that it is equipped with a robust internal switching Battery Eliminator
More informationNÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. OT 020 BENCH TOP STEAM STERILIZER USER S MANUAL
NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. OT 020 BENCH TOP STEAM STERILIZER USER S MANUAL NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. Esenboğa Yolu 22 km Akyurt - ANKARA / TURKEY Tel : (00 90 312)
More informationAN500T, AN1000, AN1000T, AN1500, AN1500T AN2000, AN2000T
Product Instruction Manual Accona AN500T, AN1000, AN1000T, AN1500, AN1500T AN2000, AN2000T Panel heater v16.5/5 Version 3.2 Jan 2015 Contents 1. Important safety points 2. Installation 2.1. Wall mounting
More informationWarnings: Specifications & Features:
Hyperion NET & DUO Series 3 Chargers - User Manual v4.6+ firmware versions. Visit http://media.hyperion.hk/dn/eos for the newest manuals, firmware, and EOS SUITE PC software Warnings: EOS chargers are
More informationINSTRUCTION MANUAL INDEX
DTXP4235 INSTRUCTION MANUAL The Onyx 235 charger is great for a huge range of charging and balancing needs for electric on-road, off-road, boat and radio applications! Charge currents up to 8 amps and
More informationPassport DC Li-Po 6S Charger. Operation Manual
Passport DC Li-Po 6S Charger Operation Manual www.dynamiterc.com Introduction Thank you for purchasing the Dynamite Passport DC Li-Po 6S Charger. The Passport line of chargers are high-performance battery
More informationSOLAR POWER - THE NEW WAY TO RV!
IMPORTANT! - YOU'RE SOLAR READY SOLAR POWER - THE NEW WAY TO RV! Your RV is PRE-WIRED for SOLAR POWER! Benefits of Solar Zamp Solar Portable Solar Kit Maximize Battery Life Electrical Independence Green,
More informationAutomatik-Lader AL 600 Automatic Charger AL 600 fcr 2-6-12V / for 2-6-12V. Best.-Nr. : 12 42 21 7 / Order No. 12 42 21 7
Automatik-Lader AL 600 Automatic Charger AL 600 fcr 2-6-12V / for 2-6-12V Best.-Nr. : 12 42 21 7 / Order No. 12 42 21 7 Please read this manual carefully. For defects, which occurred due to not following
More informationDaker DK 1, 2, 3 kva. Manuel d installation Installation manual. Part. LE05334AC-07/13-01 GF
Daker DK 1, 2, 3 kva Manuel d installation Installation manual Part. LE05334AC-07/13-01 GF Daker DK 1, 2, 3 kva Index 1 Introduction 24 2 Conditions of use 24 3 LCD Panel 25 4 Installation 28 5 UPS communicator
More informationYou motor now is ready to run. Wires Connection: Installing the Controller: Normal start up:
Dear customer, Thanks for purchase of our Brushless Motor Controller. This is a new generation of sensorless speed controllers, with latest humanize software design, especially for ALL types of brushless
More informationDigital echo-charge. Owner s Manual. Xantrex Digital echo-charge Battery Charger
Digital echo-charge Owner s Manual Xantrex Digital echo-charge Battery Charger Thank you for purchasing a Xantrex Digital echo-charge. Xantrex Technology Inc. takes pride in manufacturing quality products
More informationUser s manual FLIR VP50/VP52 Non-contact AC voltage detector
User s manual FLIR VP50/VP52 Non-contact AC voltage detector User s manual FLIR VP50/VP52 #T559851; r. AD/ 9134/9134; en-us Table of contents 1 Disclaimers... 1 1.1 Copyright... 1 1.2 Quality assurance...
More informationUser s Manual Before using the inverter, you need to read and save the safety instructions.
User s Manual Before using the inverter, you need to read and save the safety instructions. STI SERIES (STI200, STI300, STI500, STI700, STI1000) Power Frequency Pure Sine Wave Inverter The information
More informationLESTRONIC DV AUTOMATIC 12 OR 24 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/24EL40-10ET
LESTRONIC DV AUTOMATIC 12 OR 2 VOLT DUAL OUTPUT DUAL MODE BATTERY CHARGER MODEL 16350 TYPE 12/2EL0-10ET PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment,
More informationTT TOYS TOYS - OWNER S MANUAL. We are delighted that you have decided to purchase this TT Toys Toys children s car.
TT TOYS TOYS - OWNER S MANUAL We are delighted that you have decided to purchase this TT Toys Toys children s car. This owner s manual contains important information for the safe assembly, handling and
More informationGAUGEMASTER PRODIGY EXPRESS
GAUGEMASTER PRODIGY EXPRESS DCC01 USER MANUAL Version 1.1 2011 T A B L E O F C O N T E N T S 1 Getting Started Introduction Specifications and Features Quick Start Connecting to Your Layout Running a Loco
More informationBattery Charger For Nickel Cadmium and Nickel-Metal Hydride Rechargeable Batteries Model PSN Series
Battery Charger For Nickel Cadmium and Nickel-Metal Hydride Rechargeable Batteries Model PSN Series Operating Instructions WARNING CONCERNING THE REMOVAL OF COVER: CAUTION: TO PREVENT THE RISK OF ELECTRIC
More informationINSTRUCTION MANUAL PLEASE READ ALL THE INSTRUCTIONS COMPLETELY BEFORE USE AND SAVE THIS MANUAL FOR FUTURE REFERENCE
INSTRUCTION MANUAL PLEASE READ ALL THE INSTRUCTIONS COMPLETELY BEFORE USE AND SAVE THIS MANUAL FOR FUTURE REFERENCE m Before Use Please read IMPORTANT SAFETY INSTRUCTIONS on page 10 before use. It is important
More informationCHARGING SYSTEMS INTERNATIONAL
CHARGING SYSTEMS INTERNATIONAL INSTALLATION AND OPERATING INSTRUCTIONS FOR THE FOLLOWING BATTERY CHARGING SYSTEMS: MODELS MAX AMPS/BANK NO. OF BANKS BATTERY SYSTEM PRO XL 6 1 12 DUAL PRO XL 6 2 12/24 PRO
More informationNucleus Freedom BTE Rechargeable Battery (A25) and Nucleus Freedom BTE Recharger
Nucleus Freedom BTE Rechargeable Battery (A25) and Nucleus Freedom BTE Recharger The Nucleus Freedom BTE Rechargeable Battery (A25) is designed for use with your Nucleus Freedom BTE Controller (3 Zinc
More informationMULTI XS 3600. Battery charger. For lead-acid batteries 1,2-120Ah
MULTI XS 3600 Battery charger For lead-acid batteries 1,2-120Ah User s Manual and a guide to professional battery charging For Starter/Deep Cycle batteries EN INTRODUCTION Congratulations on your purchase
More informationInstructions: Part I. Charge the Power Bank. Method 1. Charge the Power Bank via Computer USB Terminal.
Instructions: Part I. Charge the Power Bank Method 1 Charge the Power Bank via Computer USB Terminal. Connect the provided USB power cable to the micro- USB plug connector tip (the tip marked "M10"). Step
More informationOWNER S MANUAL 2.5/3.0 ACS PANEL (ADVANCED CONTROL SYSTEM) 7725 Lougheed Highway Burnaby, BC V5A 4V8 Canada
2.5/3.0 ACS PANEL (ADVANCED CONTROL SYSTEM) OWNER S MANUAL 7725 Lougheed Highway Burnaby, BC V5A 4V8 Canada Tel: (604) 420-1585 Fax: (604) 420-1591 http:// www. statpower.com PROsine 2.5/3.0 ACS Panel
More informationBATTERY CHARGING GUIDELINES FOR 6-VOLT DEEP CYCLE BATTERIES
BATTERY CHARGING GUIDELINES FOR 6-VOLT DEEP CYCLE BATTERIES Introduction Your 6-volt deep cycle battery set has been specially formulated for long cycle life and has particular voltage and specific gravity
More informationNFC Communication Tray Model: HHX-IT3-Z
INSTRUCTION MANUAL NFC Communication Tray Model: HHX-IT3-Z ENGLISH CONTENTS Introduction...3 Important safety information...4 Know your unit...6 Transferring data to the PC...7 Care and maintenance...8
More informationGSM Alarm System User Manual
GSM Alarm System User Manual For a better understanding of this product, please read this user manual thoroughly before using it. Quick Guider After getting this alarm system, you need to do the following
More informationMANUAL. * Supply plugs may differ to suit your wall socket. EN 3. Continue to press the MODE-button to combine charging program with charging options.
MX MANUAL CONGRATULATIONS to the purchase of your new professional switch mode battery charger. This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest
More informationTIG INVERTER INSTRUCTION MANUAL
TIG INVERTER INSTRUCTION MANUAL Contents Warning General Description Block Diagram Main Parameters Circuit Diagram Installation and Operation Caution Maintenance Spare Parts List Troubleshooting 3 4 4
More information2 Installation Explanation
Intelligent Solar Charge Controller Solar30 User s Manual Please read this instruction carefully before using it. SOLAR30 12V/24V AUTO WORK 1 Product introduction This controller is a kind of intelligent
More informationAntenna Splitter ASA 1. Instruction manual
Antenna Splitter ASA 1 Instruction manual Contents Important safety instructions... 2 The ASA 1 active antenna splitter... 4 Delivery includes... 4 Operating elements... 5 Putting the ASA 1 into operation...
More informationInstallation and Operating Instructions (for chargers shown below)
Installation and Operating Instructions (for chargers shown below) For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard,
More informationBroadBand PowerShield. User Manual
BroadBand PowerShield User Manual 990-0375G 12/2006 Chapter 1 General Information The PowerShield provides a power source for broadband telephony and other DC applications. Safety This Safety Guide contains
More informationHYDRA HV OPERATION MANUAL. 2.0 Making Connections on your HYDRA speed control. Rosin core electrical solder
HYDRA HV OPERATION MANUAL Starting Power Safe power on arming program helps prevent motor from accidentally turning on. Always use extreme care with high power systems. Auto shut down when signal is lost
More informationEPSOLAR LS0512R / LS0524R. Solar Light Controller INSTRUCTION MANUAL. Please read this manual carefully before using the product!
EPSOLAR LS0512R / LS0524R Solar Light Controller INSTRUCTION MANUAL Please read this manual carefully before using the product! LandStar LS0512R / LS0524R Solar Light Controller Nominal system voltage
More informationOCSM Series. High Resolution Digital Crane Scale. User Guide
OCSM Series High Resolution Digital Crane Scale Content 1. Safety Guide... 1 2. Features... 1 3. Specifications... 2 4. Capacity... 3 5. Display & Keys... 3 Scale & Remote Keys... 3 Indicators... 4 Message...
More informationCellpro 10XP Charger. User s Guide
Cellpro 10XP Charger User s Guide Copyright 2011, 2014 FMA, Inc. Updated 09/02/2014 Table of Contents Table of Contents... 2 Description... 3 Features... 3 Precautions... 5 Parts... 5 Charger terminology...
More information400 Amp Rechargeable Jump Start System RAC-HP082
400 Amp Rechargeable Jump Start System RAC-HP082 MAINTENANCE Always inspect the tool before use to ensure the cables are in good condition and the clamps are clean and free from corrosion. Keep clean by
More information3 WATT LED SPOTLIGHT Model No. SLM - 3801
3 WATT LED SPOTLIGHT Model No. SLM - 3801 OWNER'S MANUAL Customer Service Tel: 1-800-268-3319 Superex Canada Ltd, Toronto,M2H 3B8 Made in China Table of Contents A). Important Safety Instructions B). Charging
More informationFLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION
FLUORESCENT UV- RING LIGHT OPERATING INSTRUCTION Caution! UV-radiation of this device is in the range of UV-A (320-400 nm). Direct exposure to eyes shall therefore be avoided. UV protection glasses shall
More informationSNMP Web Management. User s Manual For SNMP Web Card/Box
SNMP Web Management User s Manual For SNMP Web Card/Box Management Software for Off-Grid Inverter Version: 1.2 Table of Contents 1. Overview... 1 1.1 Introduction... 1 1.2 Features... 1 1.3 Overlook...
More informationPassport Ultra 100W LCD AC/DC Multi-Chemistry Battery Charger
Passport Ultra 100W LCD AC/DC Multi-Chemistry Battery Charger Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni NOTICE All instructions, warranties and other collateral
More informationOUTPUT CABLE CONNECTIONS:
Tender Plus: Models: 12V1.25A and 6V1.25A The Tender Plus 12 Volt, 1.25 Amp 6 Volt, 1.25 Amp GENERAL DESCRIPTION: The Tender Plus battery charger is a desktop, portable, linear power converter that has
More information12 Volt 30 Amp Digital Solar Charge Controller Installation & Operation Manual
12 Volt 30 Amp Digital Solar Charge Controller Installation & Operation Manual This 30Amp charge controller is designed to protect your 12Volt Lead-acid or Gel-cell battery from being overcharge by solar
More informationMagnetek MLTX, SLTX and Pendant Battery Charger. Instruction Manual. NiMH Battery Charger (Smart Charger) For use in:
Magnetek MLTX, SLTX and Pendant Battery Charger NiMH Battery Charger (Smart Charger) Instruction Manual For use in: E10670, E10757 and E10759 Battery Charger Assemblies October 2011 Part Number: 178-00204-1000_R00
More informationInstallation/Operator Manual For use with WFCO ULTRA III Power Center Model WF-8712P and WF-8725P
Installation/Operator Manual For use with WFCO ULTRA III Power Center Model WF-8712P and WF-8725P Distributed in the U.S.A. and Canada by CHENG USA, INC. Sales (574) 294-8997 Warranty Service (877) 294-8997
More informationCharge Regulator SCR 12 Marine
Charge Regulator SCR 12 Marine Manual Many thanks for purchasing a superwind product. The SCR 12 Marine is a charge regulator of highest quality and will perfectly and reliably charge your batteries for
More informationCopyright. Trademarks
Copyright 2015 Sanford, L.P. All rights reserved. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into another language without the prior
More informationSpec. No. ICR18650-26C Version No. 0.0
1. Scope This product specification has been prepared to specify the rechargeable lithium-ion cell 2. Description and Model 2.1 Description Cell (lithium-ion rechargeable cell) 2.2 Model ICR18650-26C 3.
More informationHow To Use A Power Supply Unit (Upu)
BRAVER UPS (Uninterruptible Power System) User s Manual Safety CAUTION! This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains no user replaceable parts.
More informationCONTENTS. 1. Reventon ESC Features. Page1. 2. Specifications.. Page1. 3. ESC s indicating LEDs.. Page5. 4. Wiring Diagram. Page5
CONTENTS V2.1 Created on Nov 5 th 2013 1. Reventon ESC Features. Page1 2. Specifications.. Page1 3. ESC s indicating LEDs.. Page5 4. Wiring Diagram. Page5 5. Throttle Range Setting/Calibration.. Page6
More informationPassport AC/DC Li-Po 6S Charger. Operation Manual
Passport AC/DC Li-Po 6S Charger Operation Manual www.dynamiterc.com Introduction Thank you for purchasing the Dynamite Passport AC/DC Li-Po 6S Charger. The Passport line of chargers are high-performance
More informationManual Ranging MultiMeter
Owner s Manual Manual Ranging MultiMeter Model 82345 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product.! Safety! Operation! Maintenance!
More informationPIPELINE INSPECTION COMPANY LTD. Portable Holiday Detectors. OPERATING INSTRUCTIONS SPY PORTABLE HOLIDAY DETECTORS Models 780, 785, & 790
PIPELINE INSPECTION COMPANY LTD. Portable Holiday Detectors OPERATING INSTRUCTIONS SPY PORTABLE HOLIDAY DETECTORS Models 780, 785, & 790 Safety Disclaimer Only trained and responsible personnel should
More informationHow To Control A Battery Cell Phone With A Battery Power Control System
Wind/Solar Hybrid Street Light Controller User Manual Model: HY-WSC04-12AWM, HY-WSC04-12/24AWM, HY-WSC06-24AWM, HY-WSC06-48AWM 1. Product Introduction The wind/solar hybrid street light controller is an
More informationSuperior Lithium Polymer Battery
Superior Lithium Polymer Battery July 18, 2003 KOKAM ENGINEERING CO., LTD Dimension Specifications Specifications NO ITEM SPECIFICATIONS REMARKS 1 Nominal Capacity *1 TYP.1500mAh 2 Nominal Voltage 3.7
More informationBATTERY CHARGER MULTI US 7000
US Switch Mode BATTERY CHARGER For lead-acid batteries 14-150 Ah MULTI US 7000 User s Manual and a guide to professional battery charging For Starter/Deep Cycle batteries INTRODUCTION The MULTI US 7000
More informationBattery Power Inverters
Battery Power Inverters Renogy 500W 1000W 2000W Pure Sine Wave Inverter Manual 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 1 Version 1.1 Important Safety Instructions Please save these instructions.
More informationPSC-A5 Solar Charge Controller Manual
( 5A, 12V/24V Output, Double Mode ) 1. Introduction: This controller is suitable for 12V and 24V solar photovoltaic system. The charge and discharge current is 5A. The maximum solar panel for 12V system
More informationDear Neuton Owner, This is a helpful hint to guide you in getting the most out of your NEUTON Battery and Charger.
Battery-Powered Mower NEUTON 24-Volt Charger Instructions Booklet Dear Neuton Owner, In order for you to get the most out of your Neuton Mower, we recently reviewed and revised our battery-charging instructions.
More informationInstallation and Operation Back-UPS 1250, 1300, 1500
Installation and Operation Back-UPS 1250, 1300, 1500 Inventory bu001a Safety and General Information This unit is intended for indoor use only. Do not operate this unit in direct sunlight, in contact with
More informationAUTO CHARGE 3 STEP AUTOMATIC BATTERY CHARGER
FILE: IM_091-120-12E-20 Rev A., 05-06-08 INSTRUCTION MANUAL AUTO CHARGE 3 STEP AUTOMATIC BATTERY CHARGER R MODEL #091-120-12E-20 for ODYSSEY AGM BATTERIES CAUTION This charger is calibrated to the ODYSSEY
More informationGV-Boost Manual. 8A Input / 105-350W IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. Solar Charge Controllers with Maximum Power Point Tracking
GV-Boost Manual Solar Charge Controllers with Maximum Power Point Tracking For models: GVB-8-Pb-12V: GVB-8-Pb-24V: GVB-8-Pb-36V: GVB-8-Pb-48V: GVB-8-Li-**.*V: 12V Lead-Acid/AGM/Gel/Sealed/Flooded 24V Lead-Acid/AGM/Gel/Sealed/Flooded
More informationPeak Atlas IT. RJ45 Network Cable Analyser Model UTP05. Designed and manufactured with pride in the UK. User Guide
GB05-6 Peak Atlas IT RJ45 Network Cable Analyser Model UTP05 Designed and manufactured with pride in the UK User Guide Peak Electronic Design Limited 2001/2012 In the interests of development, information
More informationMANUAL EN 3. Continue to press the MODE-button to combine charging program with charging options.
MANUAL CONGRATULATIONS on the purchase of your new professional switch mode battery charger and tester. This charger and tester is included in a series of professional chargers from CTEK Sweden AB and
More informationBlueSolar Pro Remote Panel For BlueSolar PWM-Pro charge controllers 12/24V 5, 10, 20, 30A Article number SCC900300000
Manual EN BlueSolar Pro Remote Panel For BlueSolar PWM-Pro charge controllers 12/24V 5, 10, 20, 30A Article number SCC900300000 Contents EN 1.Important safety instructions... 2 2. Installation... 2 3.Product
More information2/8/12 AMP Smart Charger OWNER S MANUAL
2/8/12 AMP Smart Charger OWNER S MANUAL Model number-457808 Important For safe and optimum performance, charger must be used properly. Carefully read and follow all instructions and guidelines in this
More informationPoint of view HDMI Smart TV dongle Mini RF Keyboard
Point of view HDMI Smart TV dongle Mini RF Keyboard English Contents Contents... 1 General notices for use... 2 Disclaimer... 2 Box Contents... 2 1. HDMI TV dongle... 3 1.1. Product display... 3 1.2. Instructions
More informationUserʼs Manual. 7 Color LCD TV & Monitor V7000
Userʼs Manual 7 Color LCD TV & Monitor V7000 Dear Customers Thank you for purchasing the ikan V7000 7 LCD TFT Monitor. This product employs new integrate circuitry, and a high quality TFT LCD panel. It
More informationMy Weigh Ultraship Series User Manual
My Weigh Ultraship Series User Manual Low Batteries, bad battery connections & Faulty AC Adaptors are the #1 cause of Ultraship malfunction and inaccuracy! We test all of our scale returns from consumers.
More information