NavEye BlackBox GSM/GPS alarm manual

Transcription

1 NavEye BlackBox GSM/GPS alarm manual NavEye BlackBox protects your belongings and vehicles in various ways. Equipped with external sensors the alarm can detect when a door or a hatch is opened and if the engine starts. The geofence function keeps track of the vehicles GPS position and alerts when it moves. Internal sensors controls not only the geofence but also the internal and external voltage, speed and course while moving, alarm status and more. The information can be retrieved by texting or by calling your NavEye BlackBox. It can be controlled and configured both from a cell phone or from the internet on Contents NavEye BlackBox GSM/GPS alarm manual...1 SIM-card...2 Fitting...2 Install external NavEye BlackBox Plus sensors...2 Start up...3 Activate...4 Remote control...4 Functions...4 Geofence alarm...5 Voltage warnings & alarms...5 Motion alarm...5 Gas & Fire alarm...6 Burglary alarm...6 Water level guard...6 Support...6 1

2 SIM-card Your NavEye BlackBox is delivered with a SIM-card preloaded with 50 SEK that will cover the first period in use. The balance should be controlled and refilled to make sure that the unit always is able to send alarm. Number presentation must be activated on your cell phone to enable the unit to identify and grant access and it should also be able to send and receive text SMS. Please make sure of this before installing your NavEye BlackBox. After the installation you will need a computer with internet connection to register and configure the unit. Fitting NavEye BlackBox is recommended to be fitted in a hidden place where it s not easily detected but it s an advantage if it is possible to see the LEDs during the installation and start up. External GSM antenna might be needed when the unit is installed in a way that prevents it from obtaining a good GPS signal. The signal is blocked by metal or concrete and weakened by thick wood, plastic or glass. The optimal placement for the unit is according to the picture. Connect the NavEye BlackBox to a 8-32 volt DC power source and before the main switch. 1. Gray cable connects to minus on the battery 2. Red cable to plus. The unit is protected with an internal fuse and if it should be released, the unit has to cool down for 10 minutes before it resets itself. The installation so far covers functions like geofence, tracking, vibration warning, emergency button, supply voltage warning. To add more security functionality like burglar alarm, fire alarm you ll need to connect external sensors and upgrades to BlackBox Plus. Install external NavEye BlackBox Plus sensors There are two different types of sensors, disconnecting (Normal High) and connecting (Normal Low). For example a burglar alarm with a magnetic switch (the power) is on in armed state, and when a door opens the contact breaks and the power drops, which in turn triggers the alarm to go off, the burglar alarm is there for normal high. The consequences of this is that if you don t connect a sensor the input cable must be connected to either plus or minus to avoid false alarms and warnings. Input (Normal state): 1. Pink - Gas & Fire Fire and Gas detectors (Low) (Normaly open) Connects to plus. 2. Yellow Burglary IR-detectors and magnetic switches (High) (Normaly closed) Connects to plus. 3. Green Water level guard (Low) (Normaly open) Connects to plus. 4. Brown Grounding sensor - (High) (Normaly closed) Connects to plus. 2

3 Output: (Do not connect cables if not in use) 1. Blue Immobilizer Activated in armed state 2. White Relay control Controlling electronic equipment like heaters, lights Output 1, is preset to attach an immobilizer equipment. It s activated in armed state and can be controlled both with the remote control and a cell phone. Output 2, is configured for attaching relay controlled equipment. To activate send out2,1 from your cell phone and to inactivate send out2,0 and the unit will respond with a answer. Start up When your NavEye BlackBox is installed and connected to an external power source the internal battery will start charging and after a few minutes the unit will start and indicate it with a beep and the LEDs will be turned on. To allow the unit to start up and to get fully charged please do not remove the external power the first hour. When the unit is awake and in a disarmed state the LEDs will indicate the status for GPS and GSM signals. LED A gives a steady green light when it s trying to get a good fixed position and also if it already has got a position. Only when it has a very good and stable position the LED will give a blinking light. LED B will indicate the GSM signal with a slow blinking yellow light (that reminds of older cell phones that had blinking lights). Both LEDs are turned off in armed state and after a few minutes in idle. This behavior will prevent the NavEye BlackBox to reveal its location. It can take some time before the unit gets its first GPS fixed position. This is depending on the placement of the unit and the surroundings. If no position is found the answering text SMS s from the unit will contain only zeros in the attached positioning link. To obtain the optimal conditions for the unit please control its position and that it s not blocked by metal or any other material that could affect its function. Tall buildings and rocks will affect the signal and in difficult areas the unit might have to be complemented with an external antenna. NB!! Make sure that your NavEye BlackBox always has the best possible GPS and GSM signal to guarantee the best protection of your property! When the unit has started and got signal you should check the status by calling it from your cell phone. You can find the number enclosed in the packaging. Make sure that your cell phone isn t connected to a switchboard and that it displays its number when calling. Within seconds your NavEye BlackBox will respond similar to the examples below. Response when calling a: NavEye BlackBox S.N: 1012xxxx Ver: VI: 3.754V VE: V GPS: Searching In1(Pink): Low In2(Yellow): Low In3(Green): Low In4(Brown): Low 3

4 Activate To activate your NavEye BlackBox visit and register your new user account. Submit the serial number and the cell phone number enclosed with the unit and push the Register button. (NB! It s important that you submit the right numbers!) State your NavEve BlackBox serial number and mobile telephone number attached to your delivery and push Register.(It s important that you use the correct number!) 1. Submit your personal information in the boxes and create your account. 2. Submit your settings and insurance information under each category. 3. Open My BlackBox and start by adding alert receiver. This cell phone number will receive all alarms and warnings sent out by your BlackBox. - Add, send and wait for the reply. 4. Add access phone by adding the number to the cell phone that will have the rights to control your BlackBox. -Add, send and wait for reply. 5. Choose the configuration button for the kind of vehicle your NavEye BlackBox will guard. This will configure your unit with the optimal parameters for your usage. Remote control Blue button Activates the alarm, a long beep will confirm armed status. Yellow button Deactivates the alarm, two short beeps confirms disarmed status. Red button The unit will send an emergency message to the set receiver. ( NB! At least one recipient number must be added for this function to be active!) White button No further action, lighting up the LEDs in disarmed status. Functions Your NavEye BlackBox has several built in functions and together with external accessories it is a complete alarm and safety solution for your car, boat, trailer or any other vehicle you want to protect. The NavEye BlackBox separates alarms and warnings where warnings are always active and alarms are only active in armed status. For example, the burglary alarm is only active while it s armed and the gas & fire warning is always active to detect fire even if you are using you vehicle. To reset a alarm use the remote or your cell phone and arm the unit again, this will reset and activate the alarm again. 4

5 Geofence alarm Your NavEye BlackBox are constantly surveying your vehicles position using the GPS technology. When arming your unit it will lock on the current position and the alarm is activated. If the vehicle moves out of the geofence area the alarm will go off and you will receive an alarm SMS as seen below. SMS Larm NavEye BlackBox GEOFENCE ALARM GPS time: :24:37 Spd: 0 Hdg: 199 Bat int: 4.135V Bat ext: V -Message header -GPS-position set time(gmt/utc) -Speed Km/h -Heading -Internalbattery voltage -External voltage -Link with latitude and longitude Voltage warnings & alarms The NavEye BlackBox monitors both the internal voltage and the external and warns or alarms depending on the situation. If the external voltage is lost or the cables are cut and the unit is armed, the unit will trigger the lost voltage alarm. If the external battery is losing power the BlackBox will warn when it goes below 11.7 volts, this warning can also be triggered at a engine start if the unit is connected to the start battery. If so please contact the support and they will deactivate this warning. Warning on low internal voltage is triggered when the battery goes below 3.7 volts. SMS alarm at missing external voltage SMS alarm title: NavEye EXT BATT LOST VOLT ALARM SMS warning at low external voltage SMS alarm title: NavEye EXT BATT LOW SUPPLY WARNING SMS warning at low internal voltage SMS alarm title: NavEye INT BATT LOW VOLT WARNING Motion alarm The NavEye BlackBox comes with a built-in accelerator that warns for vibrations, motions and tilt. SMS alarm title: NavEye MOTION ALARM 5

6 Gas & Fire alarm With an external gas & fire alarm the NavEye BlackBox can monitor and warn if a LPG stove or LPG cylinder is leaking or if a fire should start when you use your boat or trailer or when you have left them locked and alarmed. SMS alarm title: NavEye Gas and Fire WARNING Burglary alarm Accessories can be connected to the NavEye BlackBox and it will then turn into an effective burglary alarm system. With magnetic switches and IR sensors it will alarm if a burglary is performed. The NavEye BlackBox burglary protection generates a silent alarm and our recommendation is to add harbor guarding or equivalent service to the list of alarm receivers in the unit. (Silent alarm is a recommendation from the insurance companies.) SMS alarm title: NavEye Burglary ALARM Water level guard With a water level guard the NavEye BlackBox will send an alarm if for example a bilge pump fails or the boat is leaking water. SMS alarm title: NavEye Water level guard WARNING Support For any further questions please don t hesitate to contact the NavEye support. Webb: support@aqualiv.com Telephone: Fax: