100 SERIES. Diesel Fuel/Water Separators. Installation. Operation. Parts. Service Information

Size: px
Start display at page:

Download "100 SERIES. Diesel Fuel/Water Separators. Installation. Operation. Parts. Service Information"

Transcription

1 Diesel /Water Separators Installation Operation Parts Service Information

2 INSTALLATION A. FILTER MOUNTED ABOVE FUEL STORAGE TANK 1. Select a location in the fuel line between the fuel tank and the fuel pump, ahead of the vacuum side filters. All secondary or pressure side filters located between the pump and the engine should be serviced and left in place.. Mount the DAHL unit vertically on the vacuum (suction) side of all fuel pumps in a convenient location for servicing and inspection of contaminants in the bowl. Locate the height of the unit between the bottom of the fuel tank and the inlet of the fuel pump if possible. See Figure 1. FIGURE 1 Engine Pump Factory Primary Filter (if applicable) Outlet DAHL recommends a 186-SK Shock Pad Mounting Kit if the filter will be subject to excessive vibration. Installation procedures are the same as above plus an addition to Step 3: A ball- or butterfly-type shut-off valve must be installed ahead of the DAHL unit INLET. See Figure. This valve is necessary to shut off fuel when changing the element. Valves are available from your dealer or by contacting Baldwin Filters. NOTE: Valve not required when installing DAHL valved manifold units. Inlet Tank NOTE: Allow 1 1/ inches vertical clearance below the unit for servicing the element and draining the contaminants. 3. Install the fuel line from the fuel tank to the DAHL filter INLET using appropriate non-galvanized fittings. See DAHL Fittings Chart below. 4. Install the fuel line from the DAHL filter OUTLET to the INLET of the transfer or fuel pump. NOTE: To obtain maximum element life, remove as much mechanical restriction as possible from the system by doing the following: a. Remove the primary filter (if this does not affect warranty). b. Use the largest diameter fuel line that is practical. c. Mount the unit as near to the level of the pump as possible. d. Eliminate sharp bends in the fuel lines wherever possible. The best indicator of a fuel element s condition is a vacuum gauge. (See (See 85-V in Form 4005.) A tapped fitting is recommended for mounting the gauge on the OUTLET port of the DAHL filter unit. (Manifold units are already tapped and plugged.) Remove the 1/8 inch plug and install the vacuum gauge there. Prime the filter as indicated under ELEMENT REPLACEMENT section. B. FILTER MOUNTED BELOW FUEL STORAGE TANK C. STANDARD FITTINGS INSTALLATION/DAHL FITTINGS CHART Engine FIGURE Pump Factory Primary Filter (if applicable) Outlet Inlet Tank Shut-Off Valve 1/4 In. Butterfly Valve 1/ In. Butterfly Valve 1063-D OBS 3/4 In. Butterfly Valve 1063-F OBS 1 Install Out Port First MODEL Elbow Fitting Compression Nut Washer O-Ring (Oil Before Use) Note: Mount Model Before Installing Fittings. O-Ring Seal Fittings Require Care in Installation. DO NOT OVERTIGHTEN. See Instructions Below. 90 Elbow Straight Thread 1 with O-Ring/37 Male JIC 90 Elbow Straight Thread 1 with O-Ring/37 Male JIC Drilled & Tapped for #4 Vacuum Gauge Hose 37 Male JIC Straight Thread with O-Ring 37 Female JIC Swivel-Push-On Hose Fitting Female Pipe Straight Thread with O-Ring Screw in O-Ring fitting until washer contacts port Hand Tighten Do NOT Only Use Wrench FITTING THREAD 1 THREAD 9/16-18 UNF 7/ /16-18 UNF 7/16-0 9/16-18 UNF 7/16-0 7/16-0 1/4 Hose 9/ /8 Hose 9/16-18 UNF 1/4-18 NPT 9/16-18 UNF 3/8-18 NPT 4 Hold fitting by hand in desired position and tighten compression nut with wrench. Adjust Compression Nut All the Way Back YES (Important: Do Not Tighten Further) NO Turn Fitting Counterclockwise to Desired Position CAUTION: Use Low Torque: No More Than 8 Foot Pounds NOTE: Use Same Procedure for In Port.

3 NOTE: The bowl should always be drained before water or contaminant levels reach the bottom of the depressurizer cone. Check daily with the engine off. Always open the draincock or remove the pipe plug completely to flush particulates out. Failure to do so could cause a leaky valve. A. DAHL Units Mounted HIGHER Than Storage Tank 1. Turn engine off. Vent the DAHL filter to allow draining.. Loosen the outlet fitting compression nut (see Illustration 4 on Page ) and then open the draincock or remove the pipe plug. If your fuel system is equipped with a DAHL primer bulb, open the draincock and squeeze the primer bulb to evacuate all contaminants. 100 SERIES SERVICING DRAINING WATER A. When To Replace As a general guideline, depending on fuel quality and engine use, elements should be replaced as follows: 1. DAHL 101 is a micron element which can be used approximately 500 hours or 0,000 miles. (DAHL 101-W is a 10 micron element for use in winter or severe applications and DAHL is a 30 micron element.). If you have a vacuum gauge, the first replacement should be made at the very first indication of power loss at high RPMs. Make a note of the vacuum gauge reading at this point. The differences in various fuel system requirements make it impossible to predict what this reading will be. Mark the reading on the gauge dial or the unit for future element replacement. B. How To Replace Contaminated Element 1. Open the draincock or remove the pipe plug completely to empty the bowl and flush particulates out. Failure to do so could cause a leaky valve.. Loosen, but don t remove, the lid clamp knob. Support the filter body with your hand prior to release. 3. Remove the element with a turning motion. At this point, you may clean the outside of the filter body. Use only clean diesel fuel or kerosene and wipe clean. 4. Check the centerpipe O-Ring and replace if hard or damaged. 5. Remove and replace the lid gasket. Be sure the lid groove and body lip are clean. (Grease the lid cover gasket before positioning.) 3. Close the draincock or replace the pipe plug and follow the priming instructions shown below. B. DAHL Units Mounted LOWER Than Storage Tank 1. Turn engine off and close shut-off valve. (Valved Manifold units may be drained and elements replaced with the engine running at idle. Close the inlet and outlet valves to isolate the filter being serviced.). Open the draincock or remove the pipe plug completely and drain all contaminants. 3. Close the draincock or replace the pipe plug and follow the priming instructions shown below. ELEMENT REPLACEMENT TROUBLESHOOTING Engine starting and power loss problems from the fuel system are usually caused by one or more of the following: A. Air Leaks 1. Fittings. Insure the O-Rings on the fittings in the DAHL filter ports are lubricated and not damaged, cracked or dirty. NOTE: When using JIC 37 fittings, be sure only mating JIC 37 fittings are used. Misalignment will occur and air leakage will result from an attempt to fasten a 45 fitting to a JIC 37 fitting. Check for fitting looseness, seat dents, misalignment or unmatched threads. All fittings must be wrench tight.. Bubbles In The Bowl. If bubbles appear at the depressurizer cone, a leak is indicated between the fuel tank and the inlet port. NOTE: Old fuel lines (rubber hose or metal tubing) may crack when moved. Check areas around push-on fittings, pipe adapters, hose clamps, etc. If air bubbles appear at the draincock, check for particles stuck in the valve seat or a partly open draincock. Also check for defective, miscentered or unlubricated bowl gaskets. Check the bowl plug O-Ring to make sure it is not cracked or extruded out of place. The bowl plug should be hand tightened only. 3. Gaskets. If the lid or bowl has been removed, make sure the gasket grooves are clean. Inspect the gaskets for proper C. Reassembly 1. Lubricate the top and bottom element gaskets. Install the element onto the centerpipe with a turning motion.. Fill the filter body with clean diesel fuel to within one inch of the top. 3. Double check the lid cover gasket position in the lid groove. 4. Attach the body to the lid and hand tighten the lid clamp knob. Check the circumference of the body and lid for proper clamp alignment. (See up arrows on band for correct orientation.) D. Priming 1. Eliminate air use existing fuel system primer, if so equipped. a. If the DAHL primer bulb is installed, loosen the swivel fitting on the outlet port and squeeze the bulb repeatedly until the diesel fuel appears at the swivel. Then tighten the swivel fitting. B. If no primer bulb is installed, remove the inlet port elbow fitting and fill to the top with clean diesel fuel. (Or, if you can pivot the unit upside down, prime it through the bowl plug.) For ease of priming, installation of a primer pump kit ( KIT) with every Model 100 series is recommended.. Start engine and check for leaks. NOTE: For any marine or other unit utilizing the heat deflector shield, clean the shield to remove any accumulated diesel fuel. seating in the grooves. Lubricate the gasket(s) with oil or grease. B. Clogging And Restriction 1. Lines. Check for collapsed lines caused by sharp bends or excessive turns. Check the tank and/or filter shut-off valve(s).. Filter Elements. Early clogging can occur from badly contaminated fuel (micro-organism growth, rust, sludge, dirt, etc.) Always carry a spare DAHL element. Asphaltinic materials (fuel oxidation products), which are normally harmless to the injection system, can eventually plug original equipment filters remaining in the fuel system. If problems persist after the DAHL element has been replaced, also replace the other fuel filter elements. 3. Filter Inlet. Severely contaminated fuel may cause inlet plugging. In this event, close the fuel tank supply shut-off valve (if equipped) and disconnect the inlet line. Remove the bowl and clean the inlet. Should the depressurizer cone also be plugged, disassemble and clean out. 4. Bleed Back. If fuel in the DAHL filter bleeds back to the fuel tank, an air leak or reverse flow valve problem is indicated. Inspect fuel lines and fittings first as indicated above. If the reverse flow valve is clogged, use air or clean fuel to flush out. C. Malfunction Of Engine Parts Pre-existing conditions in pumps and injectors can also cause power loss and engine starting problems. See your equipment dealer if the above troubleshooting guides do not cover your problem. 3

4 REBUILD PROCEDURE If it is ever necessary to dismantle the unit for inspection and/or possible repairs, refer to the parts illustration. Then follow these simple steps: 1. Refer to the appropriate ELEMENT REPLACEMENT steps for disassembly. (Dismount if desired.). Remove the socket head bolts from the bowl ring to release the bowl. Stubborn bolts are easily removed by shocking the head. Place the allen wrench into the bolt and lightly rap the wrench with a hammer. Remove the bolt. 3. Unscrew the depressurizer cone to inspect the reverse flow valve. Caution: Cone edges are sharp. Use gloves or a rag for protection. 4. Check all parts for damage. Replace all damaged parts or hard gaskets. (Order 100-GK Gaskets for 100 Series.) 5. Refer to the parts illustration for reassembly. Clean all gasket grooves and contact surfaces of foreign matter. Coat the lid cover gasket with grease and all other gaskets and O-Rings with diesel fuel. Hand tighten the depressurizer cone and wrench tighten the socket head bolts. 6. Again, refer to ELEMENT REPLACEMENT section to finish reassembly. HOW THE DAHL SYSTEM WORKS The contaminated fuel enters the inlet port.. The T-Bolt redirects the fuel downward through the centerpipe. 3. flows through the reverse flow valve. 4. flow is spread by the depressurizer cone. 5. As fuel is discharged from the depressurizer cone, 80% of contaminant separation takes place. Most of the solid particles and water settle into the quiet zone of the bowl. 6. As the fuel rises upward, any remaining minute water droplets coalesce on the cone, baffle and bowl surfaces. Droplet size and weight gradually increase, causing downward flow into the sump. 7. is filtered completely by the element, which contains HydroShield media. The clean fuel then continues upward through the outlet port and on to the pump and injection system. 4

5 PARTS & SPECIFICATIONS MODEL 100 SPECIFICATIONS Recommended Flow Rate: (For Optimum Element Life & Separation Efficiency) Single Model 100 Series...40 GPH (U.S.) (151 LPH) Double Model 100 Series...80 GPH (U.S.) (30 LPH) Maximum Flow Rate: Single Model 100 Series...65 GPH (U.S.) (46 LPH) Double Model 100 Series GPH (U.S.) (49 LPH) Flow Resistance: In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range: to 5 F (-45 to 107 C) Port Thread: Single Units...9/16-18 w/o-ring Boss Double Units...1/4-18 NPT Overall Height:...1 1/ In. (317.5 mm) Width:...5 1/ In. (139.7 mm) Depth:...6 1/ In. (165.1 mm) Dry Weight:...5 lbs. (.7 kg) Element Removal Clearance:...1 1/ In. (38.1 mm) Sump Capacity:...8 oz. (36 ml) Seal Material:...Buna N Element Number: ( Micron) 101-W (10 Micron) (30 Micron) Element Material:...Resin Impregnated Cellulose NOTE: For Marine Versions of the DAHL Model 100, refer to Form 413. ACCESSORIES (All Inlet & Outlet Fittings Require O-Ring Seals) Aluminum Bowl AL Clear Bowl w/water Sensor Probes BP Clear Bowl w/heater Probes H Clear Bowl w/water Sensor and Heater Probes HBP OBS Clear Bowl w/marine Collar for Marine Units M Fittings...See DAHL Fittings Chart Heat Deflector Shield for Marine Units DS Heater Kit...55-EK Shock Pad Mounting Kit SK Water Sensor Warning Light Kit (Use with 100-1BP) 1 Volt DC...1-WLK OBS 4 Volt DC...4-WLK Hand Primers 1/4 In. Hose KIT OBS 3/8 In. Hose KIT 1.5 in. (31.8 mm) 3.65 in. (93 mm) Marine { Aluminum 100 SERIES Mounting Hole Pattern Clearance for 5/16 In. Diameter Fasteners Mounting Bracket (Incl. in 100-MNTG KIT) Fitting Bracket Bolt, Washer & Nut (Incl. in 100-MNTG KIT) Lid Cover Clamp Knob Seal Clamp with Knob Lid Cover Gasket (Incl. in 100-GK) Centerpipe O-Ring (Incl. in 100-GK) 101*,-W,-30 Element w/gasket Spring Centerpipe Body Reverse Flow Gasket (Incl. in 100-DEPR KIT & 100-GK) Reverse Flow Washer (Incl. in 100-DEPR KIT & 100-GK) Reverse Flow Ball (Incl. in 100-DEPR KIT) Bowl Gasket (Incl. in 100-GK) Depressurizer Set (Incl. in 100-DEPR KIT) Bowl Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Bowl Plug O-Ring (Incl. in 100-GK) Bowl Plug Draincock (1/4 In.) 100-1M Marine Bowl 185-DS Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Bowl Plug O-Ring (Incl. in 100-GK) Heat Deflector Shield Bowl Plug Brass Pipe Plug (1/4 In.) 100-1AL Aluminum Bowl Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Brass Pipe Plug (1/4 In.) WARNING: DO NOT use gasoline or any form of alcohol or anything which drys the skin inside or outside a DAHL Model 100 Series /Water Separator. IN-FILTER HEATER KITS Diesel fuel can become a problem in cold weather. Wax forms, plugging fuel lines and filters. DAHL has Model 100-H diesel fuel filter/water separators with the 55-EK Heater Kit included. Or you can retrofit DAHL Model 100 series diesel fuel filter/water separators with the 55-EK Heater Kit. The 55-EK Heater Kit features an electric heating element between the body and the filter element. This simultaneously heats the filter element and the fuel around it. An illuminated toggle switch conveniently located in the operator s area makes it easy to turn on and off. The unit is simple to install and operate. No seasonal adjustment or other maintenance is needed. * Standard with Unit Unless Stated. 55-EK Numbers Description & (Quantity) Heater Element (1) 100-1H Heater Probes in Clear Bowl (1) Incl. in 100-GK Bowl Gasket (1) Toggle Switch and Connectors Instructions 55-EK has Replaced the 45-EK 5

6 DAHL FUEL/WATER SEPARATORS WHY DAHL? Filters are a compromise wherever located. As a one-step strainer, a filter must be porous enough to allow sufficient flow volume. This means the filters which came with the equipment are usually in the micron range. However, if a more efficient media were used, the filter would become clogged very quickly, restricting the flow and resulting in frequent, costly element changes. Not only that, many fuel filters are not designed to remove significant amounts of water, even though water is a primary cause of injector pump and nozzle damage. Water and solid contaminants displace the diesel fuels lubricative coating on precision injection components. The loss of this protection results in wear, erosion, surface pitting and eventual fuel pressure loss. THE SOLUTION DAHL s functional dual chamber, 3-stage diesel fuel filter/water separators provide efficient suction side water separation and contaminant filtration. The key is the unique DAHL patented depressurizer cone, which spreads the flow of the fuel. The fact is, the more area to flow over, the slower the flow and the greater the separation of water and dirt from the fuel. DAHL diesel fuel filter/water separators have less mechanical flow resistance because the fuel changes direction only once. COMPLETE EFFICIENCY DAHL removes virtually 100% of the water and solid contaminants. PROVEN PERFORMANCE DAHL diesel fuel/water separators have been tested and proven over millions of miles and hours under all sorts of conditions. Ask anyone who has used DAHL, or any Baldwin user, as Baldwin Filters makes DAHL products. CLEAN FUEL DAHL eliminates nearly all of the engine problems caused by water and solid contaminants in diesel fuel. In addition to saving you the cost of expensive repair bills and aggravation, you can expect: Longer Injection System Component Life Full Power Performance Less Element Replacement Cost SUPERIOR ENGINEERING Die Cast aluminum Impact-resistant large transparent or aluminium bowl Element service life is several times longer than conventional Easy to install, service and clean Positive air elimination Advanced spring design assures positive element seal Less mechanical resistance because of streamlined flow path Baffle system is designed to stop emulsification and disperse trapped air Ball check valve to stop reverse flow Six series specifically designed to fit diesel engines of various capacities BALDWIN LIMITED WARRANTY Baldwin Filters warrants each new Baldwin or DAHL Filter Product to be free from defects in workmanship and material as follows: 1. Housings one year from date of user s purchase.. Electronics, Pumps and Motors 90 days from date of user s purchase. 3. Replaceable Elements, Spin-ons, Etc. during equipment manufacturer s recommended filter service interval, if properly installed in a Baldwin recommended application. Baldwin will replace or repair at its option, free of charge, any part still in the Baldwin warranty period found by Baldwin s inspection to be defective when such product is returned to place of purchase or to Baldwin Filters with transportation charges prepaid. Specifically excluded from this warranty is damage resulting from excessive force, negligence, abuse, misuse, misapplication, tampering, improper installation, fire or accident. The warranty will not apply to any filter which has been cut apart or subject to tampering. Also, damage to plastic parts of fuel/water separators caused by the use of fluids containing alcohol is not covered by this warranty. Full details of this warranty are in the Policy and Procedures Manual at the Baldwin or DAHL distributor or may be obtained from Baldwin s Service Engineering Department. Authorized Dealer DAHL Products Division Baldwin Filters Kearney NE (800) Form 4100 (R /15) 015 Baldwin Filters, Inc. Printed in U.S.A.

DIESEL FUEL FILTER/WATER SEPARATORS & Recycler Systems

DIESEL FUEL FILTER/WATER SEPARATORS & Recycler Systems DIESEL FUEL FILTER/WATER SEPARATORS & Recycler Systems DAHL DIESEL FUEL FILTER/WATER SEPARATORS REMOVE DIESEL FUEL SYSTEM PROBLEMS ALONG WITH WATER Water and solid contaminants displace the diesel fuel

More information

www.servicechamp.com

www.servicechamp.com 1-800-221-0216 Fax: 1-800-472-2281 www.servicechamp.com Service Champ Part 52081 Service Interval every 30,000 miles / Chevrolet 1992-2002 6.5 liter Description and Operation The fuel filter element separates

More information

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER... FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE

More information

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer

Overview PARTS LIST. B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve washer Overview READ ENTIRE INSTRUCTIONS BEFORE STARTING INSTALLATION PARTS LIST A. Flush valve B. Lever mounting base C. Flush handle assembly D. Grey/Blue float stop E. Grey float (Full Flush) F. Flush valve

More information

Installation and Operating Instructions Installation Instructions for SS EPE-316L Series

Installation and Operating Instructions Installation Instructions for SS EPE-316L Series INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This

More information

Diesel Fuel Filtration

Diesel Fuel Filtration Diesel Fuel Filtration Bio-Diesel Compatible 0 SW 0th Street Ph: () -6 Fax: () -06 Contents Separ 000 Water Separator and Fuel Filter Quick Reference Chart Installation Instructions Comparison Chart SWK-000

More information

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided) ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17) 17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure

More information

Universal Adjustable Fuel Pressure Regulator

Universal Adjustable Fuel Pressure Regulator Universal Adjustable Fuel Pressure Regulator Installation Instructions for: Part Numbers 25-302 U.S. Patent # 6,298,828! Due WARNING: to the fact that this installation deals with your fuel system this

More information

BOWIE PUMPS OPERATION - MAINTENANCE

BOWIE PUMPS OPERATION - MAINTENANCE BOWIE PUMPS OPERATION - MAINTENANCE PUMPING PRINCIPLE: The meshing owieeof the gears cause a slight depression, with the resulting enmeshing of the gears causing a vacuum drawing the fluid being pumped

More information

STEERING SYSTEM - POWER

STEERING SYSTEM - POWER STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054 owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact

More information

Stanadyne Fuel Manager Diesel Fuel Filter/Water Separator System. User s Guide

Stanadyne Fuel Manager Diesel Fuel Filter/Water Separator System. User s Guide Stanadyne Fuel Manager Diesel Fuel Filter/Water Separator System. User s Guide Brochure 99795, updated August 2002 1. Introduction Stanadyne has been making diesel fuel filters for over 30 years. Stanadyne

More information

SunMaxx Solar Filling Station Operating Instructions

SunMaxx Solar Filling Station Operating Instructions SunMaxx Solar Filling Operating Instructions Content 1. Declaration of conformity... 2 2. Introduction... 2 3. Transportation and unpacking... 4 4. Mounting and commissioning... 5 5. End of operation...

More information

In-Line Filters and Coalescers with Automatic Drains

In-Line Filters and Coalescers with Automatic Drains Instructions/Parts In-Line Filters and Coalescers with Automatic Drains 310611G EN Air Filter with Automatic Drain Part No. 22601, Series B Maintenance To maintain maximum filtering efficiency and to avoid

More information

Stainless Steel Single and Dual Circulation Kits

Stainless Steel Single and Dual Circulation Kits Instruction Sheet P/N 160780 01 Stainless Steel Single and Dual Circulation Kits Introduction The single and dual high-pressure circulation kits allow you to vary and control the circulation rate of coating

More information

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER 123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com MASTER MANUFACTURING MASTER GARDNER Part Number PCD E3 009B MM Rev 1 Nov. 2010 INTRODUCTION The purpose of this manual

More information

SureSite Magnetic Liquid Level Indicator

SureSite Magnetic Liquid Level Indicator SureSite Magnetic Liquid Level Indicator Instruction Bulletin No. 177664-1 (Rev. E) Section 1: Weldments Thank you for purchasing the GEMS SureSite Magnetic Level Indicator. Please read this document prior

More information

MP-4V Heavy Duty Riveter / 39048

MP-4V Heavy Duty Riveter / 39048 MP-4V Heavy Duty Riveter / 39048 This newly designed heavy-duty air/hydraulic riveter is ergonomically designed with the professional in mind. The light weight 3.7 lbs. well balanced MP-4V includes a Vacuum

More information

Turbocharger system components, servicing

Turbocharger system components, servicing 21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners

More information

Chapter 7 Hydraulic System Troubleshooting

Chapter 7 Hydraulic System Troubleshooting Chapter 7 Hydraulic System Troubleshooting General The following troubleshooting information is provided as a general guide to identify, locate and correct problems that may be experienced with the hydraulic

More information

Fluid Regulator. Instructions Parts List 306563L LOW PRESSURE

Fluid Regulator. Instructions Parts List 306563L LOW PRESSURE Instructions Parts List LOW PRESSURE Fluid Regulator 306563L For accurate, positive control of fluid pressure to one spray gun, dispensing valve, or atomizing head. For professional use only. 250 psi (18

More information

Failure to comply with the following cautions and warnings could cause equipment damage and personal injury.

Failure to comply with the following cautions and warnings could cause equipment damage and personal injury. 1.0 IMPORTANT RECEIVING INSTRUCTIONS Visually inspect all components for shipping damage. Shipping Damage is not covered by warranty. If shipping damage is found, notify carrier at once. The carrier is

More information

TABLE OF CONTENTS. SECTION 1 General Information: Pg 2 Description of Operation

TABLE OF CONTENTS. SECTION 1 General Information: Pg 2 Description of Operation GTRDD SERIES HEATLESS DRYER INSTALLATION, OPERATION & MAINTENANCE MANUAL TABLE OF CONTENTS SECTION 1 General Information: Pg 2 Description of Operation SECTION 2 Safety Instructions: Pg 3 Installation

More information

300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS

300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Section: MOYNO 500 PUMPS Page: 1 of 8 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Mechanical Seal Models Packing Gland Models MODELS DESIGN FEATURES

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17) 17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning

More information

Fire Hydrant Troubleshooting

Fire Hydrant Troubleshooting Fire Hydrant Troubleshooting Pulsation or chatter during opening and flow of water from hydrant. Loose condition in stem at lower valve plate nut. Tighten lower valve plate nut and secure with SS lock

More information

NITROUS TRANSFER PUMP INSTRUCTIONS

NITROUS TRANSFER PUMP INSTRUCTIONS NITROUS TRANSFER PUMP INSTRUCTIONS SAFETY TIPS Never directly inhale nitrous oxide. When inhaled in large quantities, nitrous oxide can cause respiratory ailments or in extreme cases, death by suffocation.

More information

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com 123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com INTRODUCTION The purpose of this manual is to assist you in the assembly, operation and maintenance of your sprayer

More information

BACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12

BACKPACK SPRAYERS. MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 BACKPACK SPRAYERS MODEL NOS: KSP16 & KSP20 Part Nos: 3402270 & 3402275 OPERATING & MAINTENANCE INSTRUCTIONS GC04/12 INTRODUCTION Thank you for purchasing this CLARKE Sprayer, designed for use only with

More information

FJ2. 2 Ton Trolley Floor Jack Assembly & Operating Instructions

FJ2. 2 Ton Trolley Floor Jack Assembly & Operating Instructions FJ2 2 Ton Trolley Floor Jack Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.

More information

Your safety and the safety of others are very important.

Your safety and the safety of others are very important. NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...

More information

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com

123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com 123 Industrial Loop Road Paynesville, MN 56362 Phone: 1-800-864-1649 www.master-mfg.com INTRODUCTION The purpose of this manual is to assist you in the assembly, operation and maintenance of your sprayer

More information

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES

STORAGE, INSTALLATION AND MAINTENANCE PROCEDURES GATE VALVE O.S. & Y 1.0 Periodic Inspections 1.1 The valve stem packing should be inspected at least monthly. If the stem packing shows signs of leakage, simply tighten the adjusting nuts to compress the

More information

1 5 05-12 5 05-12. Additions, Revisions, or Updates

1 5 05-12 5 05-12. Additions, Revisions, or Updates 5 05-12 1 5 05-12 SUBJECT DATE Cylinder Head May 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0023 EPA04 MBE 4000 Cylinder Head Additional

More information

Trouble Shooting. Pump

Trouble Shooting. Pump Trouble Shooting Pump Trouble Possible Cause Remedy Oil leaking in the area of water pump crankshaft Worn crankshaft seal, bad bearing, grooved shaft, or failure of retainer o-ring. Excessive play on crankshaft

More information

TYPE E Main Valve Sizes 3 /8 through 12

TYPE E Main Valve Sizes 3 /8 through 12 SD 3001F PRINTED IN U.S.A. SD 3001F/0707 A B TYPE E MAIN VALVE C D E TYPE E Main Valve Sizes 3 /8 through 12 The Spence Type E Main Valve is of normally closed, single seat design featuring packless construction,

More information

Sprinter Fuel Filter Installation

Sprinter Fuel Filter Installation This document is based on my experience with a 2002 Sprinter, and created because of the lack of manuals for the Sprinter in the US that reflects basic maintenance guidelines. The pros, no doubt, have

More information

Cooling system components, removing and installing

Cooling system components, removing and installing Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,

More information

Model 43AP Pneumatic Controller, Style B

Model 43AP Pneumatic Controller, Style B Instruction MI 011-476 January 1980 Model 43AP Pneumatic Controller, Style B Installation and Operation Model 43AP Controller continuously detects the difference between a process measurement and its set

More information

Powers Controls TH 192 HC Heating/Cooling Room Thermostat

Powers Controls TH 192 HC Heating/Cooling Room Thermostat Powers Controls TH 192 HC Heating/Cooling Room Thermostat Technical Instructions Document No. 155-066P25 TH 192-2 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 192 HC thermostats are proportional

More information

Watts Pure Water Systems

Watts Pure Water Systems Watts Pure Water Systems WM-120-PT Installation and Operation Manual Premier Water Systems Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before

More information

Installation, Maintenance, & Repair Series 4000B/LF4000B

Installation, Maintenance, & Repair Series 4000B/LF4000B Installation, Maintenance, & Repair Series 4000B/LF4000B Reduced Pressure Zone Assemblies Sizes: 1 2" 2" (15 50mm) RP/IS-A-4000B 4000B/LF4000B Size: 3 /4"! WARNING Testing Read this Manual BEFORE using

More information

PNEUMATIC PLANISHING HAMMER

PNEUMATIC PLANISHING HAMMER PNEUMATIC PLANISHING HAMMER 94847 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed Exclusively by Harbor

More information

SEPAR FILTER SEPAR 2000 SEPAR 2000

SEPAR FILTER SEPAR 2000 SEPAR 2000 2000 The 2000 is a water separator and fuel filter for light diesel fuel. An entirely new multistage centrifugal system ensures a 100% solution to the problem of water and particulate in fuel. 2000 offers:

More information

Oil and Coolant Circulating Heating System. Model - OCSM

Oil and Coolant Circulating Heating System. Model - OCSM Oil and Coolant Circulating Heating System Model - OCSM Installation & Operation Manual 216280-000 REV 2 Identifying Your System The HOTSTART heating system is designed to heat fluids for use in marine

More information

Float and Thermostatic Traps Series H, C and X

Float and Thermostatic Traps Series H, C and X Hoffman Specialty Installation & Maintenance Instructions HS-(E) and Thermostatic Traps Series H, C and X Series C & NPT Series C NPT Series X NPT Series C NPT Series H Ratings Maximum Max. Operating NPT

More information

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended

More information

Wafer Check Valve ASAHI AV VALVES. Contents. User s Manual. (1) Be sure to read the following description of our product warranty 1

Wafer Check Valve ASAHI AV VALVES. Contents. User s Manual. (1) Be sure to read the following description of our product warranty 1 Serial No. H-V066-E-2 Wafer Check Valve User s Manual Contents (1) Be sure to read the following description of our product warranty 1 (2) General operating instructions 2 (3) General instructions for

More information

2004 Technical Manual

2004 Technical Manual Marine Technical Manual T he Separ is a water separator and fuel filter for light diesel fuel. An entirely new multistage centrifugal system ensures a % solution to the problem of water and particulate

More information

Technical Guide 08/15/14

Technical Guide 08/15/14 Technical Guide 08/15/14 1 Table of Contents Contact information.3 Identifying your system..4-8 Model Number Serial number location Parts of your fuel system..9-14 Fuel pump diagram Wire harness schematics

More information

Rexroth Hydraulic Pump A10VO Series User Manual

Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic Pump A10VO Series User Manual Rexroth Hydraulic pump A10VO Series User Manual Revised 5/1/2009 Page 1 of 12 Functional Purpose This pump is preferred over a fixed displacement (gear)

More information

OPERATING INSTRUCTIONS. Shortening Filter Model No. 99-A, 102-A, & 107-A Series LIMITED WARRANTY PRODUCT SPECIFICATION

OPERATING INSTRUCTIONS. Shortening Filter Model No. 99-A, 102-A, & 107-A Series LIMITED WARRANTY PRODUCT SPECIFICATION OPERATING INSTRUCTIONS Shortening Filter Model No. 99-A, 102-A, & 107-A Series TABLE OF CONTENTS PAGE Installation... 2 Operating... 3 Cleaning... 5 Parts List... 6 & 7 Troubleshooting... 8 LIMITED WARRANTY

More information

Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW

Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW Installation, Operating and Maintenance Instructions 90/4.5.5 Rev. 0 Constantemp Double Wall Low pressure steam-water Heater F-340LDW,F-640LDW, F-940LDW and F-1240LDW Table of Contents SECTION I... 2 INSTALLATION...

More information

TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V

TITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended

More information

Extrusion Flo-Valve INSTRUCTIONS-PARTS LIST. 3000 psi (210 bar) Maximum Working Pressure. Model 204 355, Series K. Rev.

Extrusion Flo-Valve INSTRUCTIONS-PARTS LIST. 3000 psi (210 bar) Maximum Working Pressure. Model 204 355, Series K. Rev. INSTRUCTIONS-PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. 306 586 Rev. D Supercedes B Extrusion Flo-Valve Model 204 355, Series K 3000 psi

More information

Back Pack Sprayer. Operator's Manual MODELS MS - 40 MS - 50

Back Pack Sprayer. Operator's Manual MODELS MS - 40 MS - 50 Back Pack Sprayer Operator's Manual MODELS MS - 40 MS - 50 WARNING DANGER Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood

More information

Dive Rite 200 & 300 Bar Isolator Manifold Service Manual

Dive Rite 200 & 300 Bar Isolator Manifold Service Manual Dive Rite 200 & 300 Bar Isolator Manifold Service Manual Principal Photography and Text by Pete Nawrocky Copyright 2003 Lamartek Inc. D/B/A Dive Rite 0 Warning This manual is only to be used as a guide

More information

MODEL G300 BRAKE BLEEDER

MODEL G300 BRAKE BLEEDER MODEL G300 BRAKE BLEEDER Installation, Operation & Repair Parts Information Branick Industries, Inc. 4245 Main Avenue P.O. Box 1937 Fargo, North Dakota 58103 REV060616 P/N: 81-0035G 1 THIS PAGE INTENTIONALLY

More information

1/3 HP Submersible Sump Pump with Vertical Float Switch

1/3 HP Submersible Sump Pump with Vertical Float Switch 1/3 HP Submersible Sump with Vertical Float Switch Item 68476 Specifications Float Switch Operation Height 7.1 IN. ON / 2.8 IN. OFF Electrical Requirements 120V~ / 60Hz / 7.6A Power Length Maximum Capacity

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Application Outboards Faria 5 Gauge Set* Publication No. Description Part Number Honda Code PII53606A White faced, flat lens 06300-ZW5-010ZB 6315410 Issue Date Black faced, flat

More information

Hydraulic Air Riveter. Operation Manual RC197 RC198. Recommend for mass production line industrial area. Page 1

Hydraulic Air Riveter. Operation Manual RC197 RC198. Recommend for mass production line industrial area. Page 1 Hydraulic Air Riveter Recommend for mass production line industrial area Operation Manual RC197 RC198 Page 1 CONTENTS 1 Important Safety Rules 2 Tool Specification 2.1 Nomenclature 2.2 Technical Data 3

More information

Sprinter Fuel Filter Installation

Sprinter Fuel Filter Installation This document is based on my experience with a 2002 Sprinter, and created because of the lack of manuals for the Sprinter in the US that reflects basic maintenance guidelines. The pros, no doubt, have

More information

Powers Controls TH 192 S Single Temperature Room Thermostat

Powers Controls TH 192 S Single Temperature Room Thermostat Technical Instructions Document No. 155-065P25 TH 192-1 Powers Controls TH 192 S Single Temperature Room Thermostat 50 60 70 80 TH0355R1 70 80 POWERS Description The TH 192 S thermostats are proportional

More information

NUMBER: 08 DD15-10 S.M. REF.: 3.2 ENGINE: DD15 DATE: September 2008

NUMBER: 08 DD15-10 S.M. REF.: 3.2 ENGINE: DD15 DATE: September 2008 NUMBER: 08 DD15-10 S.M. REF.: 3.2 ENGINE: DD15 DATE: September 2008 SUBJECT: 3.2 OIL PAN PUBLICATION: DDC-SVC-MAN-0002 Oil pan section 3.2 has been updated. Section Change 3.2 Oil Pan Call-outs have been

More information

Fleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET

Fleck 4650. Service Manual INSTALLATION AND START-UP PROCEDURE TABLE OF CONTENTS JOB SPECIFICATION SHEET Fleck 4650 Service Manual TABLE OF CONTENTS JOB SPECIFICATION SHEET...1 INSTALLATION AND START-UP PROCEDURE...1 CONTROL VALVE DRIVE ASSEMBLY...2 CONTROL DRIVE ASSEMBLY FOR CLOCK...3 BYPASS VALVE ASSEMBLY...4

More information

Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Internet Address: http://www.powerteam.

Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031 Internet Address: http://www.powerteam. ORIGINAL INSTRUCTIONS Form No.102842 5 SPX Hydraulic Technologies 5885 11th Street Rockford, IL 61109-3699 USA Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800)

More information

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

VOYAGER 570G. 744A Sprayer Control

VOYAGER 570G. 744A Sprayer Control VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER

More information

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric

More information

The cylinder head bolts tightening stages have been updated as listed in Table 1.

The cylinder head bolts tightening stages have been updated as listed in Table 1. NUMBER: 07 EPA04 MBE 4000-6 S.M. REF.: 1.2.2 ENGINE: MBE 4000 DATE: November 2007 SUBJECT: CYLINDER HEAD BOLTS TIGHTENING STAGES PUBLICATION: 6SE412 The cylinder head bolts tightening stages have been

More information

OP300S / OP350 2:1 RATIO TRANSFER PUMP

OP300S / OP350 2:1 RATIO TRANSFER PUMP OP300S / OP350 2:1 RATIO TRANSFER PUMP OPERATING MANUAL WITH PARTS IDENTIFICATION Copyright 2013 International Pump Manufacturing, Inc. This manual contains IMPORTANT WARNINGS and INSTRUCTIONS. Read and

More information

TECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work

TECHNICAL BULLETIN. Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves. How the Cab Leveling and Chassis Leveling Valves Work Revised 02-00 TECHNICAL BULLETIN Meritor WABCO Cab Leveling Valves and Chassis Leveling Valves This technical bulletin covers both cab and chassis leveling valves manufactured by Meritor WABCO. While the

More information

LIMITED LIFETIME WARRANTY

LIMITED LIFETIME WARRANTY P D09 095G LIMITED LIFETIME WARRANTY SERIAL NO. MANUFACTURED DATE: MOTOR NO: WARRANTY STIPULATIONS: Copy of sales receipt mailed with this form All warranty information, located on back, completely filled

More information

TECHNICAL DATA. Dry 122a. November 12, 2013

TECHNICAL DATA. Dry 122a. November 12, 2013 Dry 122a 1. PRODUCT DESCRIPTION The Viking is a quick-opening device. When installed with the required external Anti-flood Device, the assembly is designed to increase the operating speed of Viking Model

More information

tire inflator with pressure gauge

tire inflator with pressure gauge tire inflator with pressure gauge Model 95583 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks

More information

Compressor Service & Maintenance Manual

Compressor Service & Maintenance Manual Compressor Service & Maintenance Manual C Series COMPRESSOR (D)C1103 (D)C1203 (D)C2106 (D)C2206 (D)C3210 Copyright 2006 DCI. All Rights Reserved. 92311, Rev. C, 08/13 1 C1000 Series Service & Maintenance

More information

Diesel Fuel Systems. Injection Nozzles

Diesel Fuel Systems. Injection Nozzles Diesel Fuel Systems Injection Nozzles Unit Terms Injection nozzle Nozzle, nozzle holder, valve, spring assembly Nozzle assembly Valve, body, and spray valve Orifice Small hole Pintle Valve which the end

More information

How To Make A Fuel Manager Filter/Separator

How To Make A Fuel Manager Filter/Separator The Versatile Diesel Fuel Filtration/Water Separator System From America s Foremost Diesel Technology Innovator STANADYNE The Versatile Fuel Filtration System FOR EVERY DIESEL ENGINE, EVERY DIESEL APPLICATION

More information

INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 16303

INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 16303 WATER MIST HAND PORTABLE FIRE EXTINGUISHERS Model B270 ¾ Gallon Model B272 2 ½ Gallon INSPECTION, MAINTENANCE AND RECHARGE SERVICE MANUAL P/N 6303 All fire extinguishers should be installed, inspected

More information

Air-Oxygen Blender. Service Manual. Model No. PM5200 Series PM5300 Series (shown)

Air-Oxygen Blender. Service Manual. Model No. PM5200 Series PM5300 Series (shown) Service Manual Model No. PM5200 Series PM5300 Series (shown) SAVE THESE INSTRUCTIONS 300 Held Drive Tel: (+001) 610-262-6090 Northampton, PA 18067 USA Fax: (+001) 610-262-6080 www.precisionmedical.com

More information

Product Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description

Product Manual. CVS Type 67AFR Filter Regulator. Introduction. Installation. Description Product Manual CVS Type 67AFR Filter Regulator Introduction This CVS Controls product manual includes instructions for the installation, adjustment, maintenance and parts ordering of the CVS Type 67AFR

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS. 2012-2015 BMW 335i 3.0L Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-754DS 2012-2015 BMW 335i 3.0L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2057DK AIR FILTER 1 2 9-0442 TUBE;

More information

Engine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator

Engine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator The Strobe light checks the unit for: Balance of operating machinery RPM of motors, engine pulleys, fans, etc. Observe belt slippage Strobe light will stop action at speeds from 200 to 6000 RPM 204-1890

More information

OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT

OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL 5-1/4 B-84-B-5 FIRE HYDRANT INDEX AMERICAN - DARLING 5-1/4 IN. B-84-B-5 FIRE HYDRANT OPERATION AND MAINTENANCE MANUAL OPERATION AND MAINTENANCE REPAIRS Operation and Maintenance...

More information

OTF Oil Fired Pool Heater

OTF Oil Fired Pool Heater OTF Oil Fired Pool Heater Installation Operation Maintenance Manual Service Policy 722010 Congratulations on the purchase of your new pool heater. In order to maintain peak performance of your pool heater

More information

Carburetion Troubleshooting Quick Reference Guide

Carburetion Troubleshooting Quick Reference Guide Carburetion Troubleshooting Quick Reference Guide SERVICE DIAGNOSTIC OVERVIEW A logical, planned approach can move service work through a repair center in a smooth and efficient manner. Fueled by information

More information

Owner s Manual. Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE

Owner s Manual. Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE Owner s Manual Models: 2S5P & 3S5P OPERATION AND MAINTENANCE OF SELF-PRIMING CENTRIFUGAL TRASH PUMPS PEDESTAL DRIVE WARNING!! Installation & Operating Instructions Self-Priming Centrifugal Pump DO NOT

More information

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8

More information

Drive shaft, servicing

Drive shaft, servicing Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,

More information

Powers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat

Powers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat Document No. 155-068P25 TH 193-4 Powers Controls Free Energy Band TH 193 HC Heating/Cooling Room Thermostat 50 60 70 80 70 TH0356R1 60 80 POWERS Description The TH 193 HC thermostats are proportional dual

More information

INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT

INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT D. L. Martin Company INGROUND, ROPED, AND HOLELESS JACK SEAL REPLACEMENT TYPICAL HYDRAULIC JACK HEAD ASSEMBLY 1 TOOLS REQUIRED: 1) Container to hold hydraulic fluid. 2) Clean rags and protective covers

More information

OPERATING AND MAINTENANCE INSTRUCTIONS PUMP TYPE 215.10

OPERATING AND MAINTENANCE INSTRUCTIONS PUMP TYPE 215.10 OPERATING AND MAINTENANCE INSTRUCTIONS PUMP TYPE 215.10 To Pump model Pump number Our order Your order Order date Reference Item number Destination Plant Before storing, installation, operation or maintenance

More information

CTV-1500 Cooling Tower Vacuum Operating & Maintenance Manual

CTV-1500 Cooling Tower Vacuum Operating & Maintenance Manual CTV-1500 Cooling Tower Vacuum Operating & Maintenance Manual Goodway Technologies Corporation 420 West Avenue Stamford, CT 06902-6384 (203)359-4708 Sales: 1-800-333-7467 Customer Service: 1-800-370-2855

More information

INSTALLATION & OPERATING INSTRUCTIONS

INSTALLATION & OPERATING INSTRUCTIONS INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.

More information

System Saver 318 Air Compressor for Mack E-Tech and ASET Engines

System Saver 318 Air Compressor for Mack E-Tech and ASET Engines Maintenance Manual 31 System Saver 318 Air Compressor for Mack E-Tech and ASET Engines Revised 08-05 NON-THROUGH DRIVE THROUGH DRIVE Service Notes About This Manual This manual provides service and repair

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

MODEL T200-F18 MODEL T125-F18 Finish Nailers

MODEL T200-F18 MODEL T125-F18 Finish Nailers P MODEL T200-F18 MODEL T125-F18 Finish Nailers IMPORTANT! DO NOT DESTROY It is the customer s responsibility to have all operators and service personnel read and understand this manual. OPERATING MANUAL

More information

INSTALLATION, OPERATION & MAINTENANCE MANUAL

INSTALLATION, OPERATION & MAINTENANCE MANUAL INSTALLATION, OPERATION & MAINTENANCE MANUAL Flanged Disk Check Valve with Strainer Ref. GENEBRE: 2450 2451 2452 1 INSTRUCTIONS FOR INSTALLATION, OPERATION & MAINTENANCE MANUAL 1. Spare parts... 3 1.1

More information