S-SupremaConfigurationGuide-DOC 7/23/2014. Suprema Biometrics Configuration Guide ACS OnSite Aparato
|
|
|
- Rachel Gibbs
- 7 years ago
- Views:
Transcription
1 S-SupremaConfigurationGuide-DOC 7/23/2014 Suprema Biometrics Configuration Guide ACS OnSite Aparato
2 Page 2 Suprema Configuration Guide ACS OnSite Aparato Table of Contents 1. SUPREMA BIOSTAR CONFIGURATION OVERVIEW BIOSTAR SOFTWARE INSTALLATION AND CONFIGURATION START THE SERVER IF THE SERVER DID NOT START START THE BIOSTAR CLIENT CONFIGURING DEVICE NETWORK SETTINGS DEVICE CONFIGURATION TO COMMUNICATE WITH BRIVO CONTROLLER CONFIGURING A CUSTOM WIEGAND FORMAT IN BIOSTAR ENROLLING AND TRANSFERRING A USER TO A DEVICE... 27
3 Page 3 Suprema Configuration Guide ACS OnSite Aparato 1. SUPREMA BIOSTAR CONFIGURATION 1.1 OVERVIEW The Suprema biometric readers communicate with a Brivo access control system after being configured via the Suprema BioStar ACM software. The BioStar must first be installed and configured on a PC. The reader can then be configured and will be able to communicate via Wiegand to a Brivo controller, thus creating a two database system. This document will explain the steps needed to configure the BioStar software, to add a device that will communicate to a Brivo controller, and to transfer a user to the device. The figure below illustrates the Brivo Aparato Suprema topology. All wire harnesses necessary are included when purchasing a Suprema reader from Brivo. Suprema 12VDC power supplies for the readers are sold separately. Be sure to have the following required hardware and software components supplied: Suprema fingerprint reader Suprema BioMini enrollment scanner Brivo controller BioStar ACM admin client software BioStar ACM admin server software NOTE: The following includes installation steps for the Suprema BioStar software and the initial programming of the Suprema readers via the local network. The reader comes ready for programming; though prior to conducting the following steps you must power down the Suprema reader and connect it to a hub or switch to create a local private network (do not directly connect to the programming computer).
4 Page 4 Suprema Configuration Guide ACS OnSite Aparato 1.2 BIOSTAR SOFTWARE INSTALLATION AND CONFIGURATION A. OVERVIEW: BioStar is a distributed intelligence system. Suprema's access control devices are connected via TCP/IP. User information, access rules and other data can be distributed to each device to speed up authorization time and provide continual operation even when the connection to the network is lost. B. WORKSTATION SYSTEM REQUIREMENTS: 1. BioStar supports the following operating systems: a. Windows 7 b. Windows Server 2008 R2 c. Windows Vista. d. Windows XP, Service Pack 1 or later e. Windows 2003 f. Windows 2000, Service Pack 4 or later 2. The minimum systems requirement for installing and operating the BioStar software include the following: a. CPU - Intel Pentium or similar processor, capable of processing speeds of 1GHz or faster. b. RAM - 512MB c. HDD - 5GB 3. However, Suprema recommends the following hardware configuration for optimal performance: a. CPU - Intel Pentium Dual Core or similar processor, capable of processing speeds of 2GHz or faster. b. RAM - 1GB for Windows C. INSTALLATION: 1. Install the BioStar Software: a. Contact Brivo Customer Care for a link to download the BioStar software: i option 1 ii. customercare@brivo.com 1.3 START THE SERVER A. On your desktop, you should find a green icon labeled BioStar Server Config. B. Right click on this icon and select Run as Administrator (For Windows XP or older systems you can ignore this and open application). C. When the Server Config program starts for the first time, an error message will pop-up. Click OK. D. Click Start in the upper right hand corner of the window. NOTE: If the service did not start, please ensure that you are running the application as administrator (Step 2) or skip to If The Server Did Not Start, section 1.4.
5 Page 5 Suprema Configuration Guide ACS OnSite Aparato E. An IP address will now appear in the status bar. Click OK at the bottom of the page. F. If the service started, close the BioStar Server Config window. 1.4 IF THE SERVER DID NOT START A. Open Windows Services (Control Panel > Administrative Tools > Services). B. Right click BioStar Server, click Properties.
6 Page 6 Suprema Configuration Guide ACS OnSite Aparato C. Set the Startup Type to be Automatic. D. Click Start. E. Close all windows. 1.5 START THE BIOSTAR CLIENT A. Now that the Server has been configured, click on the BioStar Client icon located on your desktop. B. A login screen will appear and say Connected to Server just above the login button. Click Server Setting. C. Enter as the Server IP (Or the PC s current IP Address running BioStar Server). D. If you are unsure, confirm the Server IP matches the IP address in the Server Config program. Click Save. E. Click Test and ensure that Connected To Server is displayed.
7 Page 7 Suprema Configuration Guide ACS OnSite Aparato F. Click Save. G. The login screen will prompt for a username and new password. This will create the first administrator of the system. Fill in the required information then click OK. H. The BioStar home screen will now pop-up. 1.6 CONFIGURING DEVICE NETWORK SETTINGS A. BIOENTRY PLUS/BIOENTRY W NETWORK SETTINGS (USING A DHCP-SUPPORTED LAN RECOMMENDED): 1. Connect the BioEntry Plus/BioEntry W to your LAN via Ethernet. 2. Ensure that the PC running BioStar is on the same subnet as the reader. 3. In BioStar, click the Device menu tab. 4. Click Add Device (located under Tasks on left side).
8 Page 8 Suprema Configuration Guide ACS OnSite Aparato 5. Select LAN and click Next. 6. Check the box for UDP and click Next. 7. Wait for the device to be found and then click Next (if the device was not found, ensure that the reader is on the same subnet as BioStar, or repeat Step 6 choosing TCP to search for a range of IP addresses).
9 Page 9 Suprema Configuration Guide ACS OnSite Aparato 8. Click the checkbox next to the device, then click Add. 9. A dialogue box 1 Device Added should appear. 10. Click OK and then Finish. B. BIOENTRY PLUS/BIOENTRY W NETWORK SETTINGS (DIRECT CONNECTION TO PC): 1. Statically set your PC running BioStar to the following address: a. IP Address: b. Gateway: c. Subnet: The following steps refer to the dip switches located on the back of the BioEntry Plus models (for BioEntry W models, please use the RESET soft button located on the back of the device): a. Turn off BioEntry Plus power (BioEntry W models, please skip this step). b. Switch DIP SW #2 to the ON position Fig.1 (BioEntry W models, please press and hold the RESET button for 5 seconds). c. Power up the BioEntry Plus unit (BioEntry W models, please skip this step). d. The device IP address has now been reset to
10 Page 10 Suprema Configuration Guide ACS OnSite Aparato 3. In BioStar, click the Device menu tab. 4. Click Add Device (Located under Tasks on the left side). 5. Select LAN and click Next. 6. Check the box for TCP. 7. Enter as the starting range. 8. Enter 2 as the ending range. 9. Click Next. 10. Click on the device once it is found and modify the IP Address, Gateway, and Subnet to the following settings:
11 Page 11 Suprema Configuration Guide ACS OnSite Aparato a. IP Address: b. Gateway: c. Subnet: NOTE: Do not enable Server or modify the ports. 11. Click Modify and confirm changes. 12. Disconnect power from the device (BioEntry W models can skip this step). 13. On the BioEntry Plus, move DIP SW #2 back to the OFF position Fig.2 (BioEntry W models can skip this step). 14. Power up the BioEntry Plus (BioEntry W models can skip this step). 15. In BioStar, click the Device menu tab. 16. Click Add Device (Located under Tasks on the left side). 17. Select LAN and click Next. 18. Check the box for TCP. 19. Enter as the starting range.
12 Page 12 Suprema Configuration Guide ACS OnSite Aparato 20. Enter 16 as the ending range. 21. Click Next. 22. When the device is found, click Next. 23. Click the checkbox next to the device, then click Add. 24. A dialogue box displaying 1 Device Added should appear. 25. Click OK and then Finish.
13 Page 13 Suprema Configuration Guide ACS OnSite Aparato C. BIOSTATION T2 NETWORK SETTINGS (using a DHCP-Supported LAN): 1. Connect the BioStation T2 to your LAN via Ethernet. 2. Ensure that the PC running BioStar is on the same subnet as the BioStation T2. 3. In BioStar, click the Device menu tab. 4. Click Add Device (located under Tasks on left side). 5. Select LAN and click Next. 6. Check the box for UDP and click Next.
14 Page 14 Suprema Configuration Guide ACS OnSite Aparato 7. Wait for the device to be found and then click Next (if the device was not found, ensure that the BioStation T2 is on the same subnet as BioStar, or repeat Step 6 choosing TCP to search for a range of IP addresses). 8. Click the checkbox next to the device, and click the Add button. 9. A dialogue box displaying 1 Device Added should appear. 10. Click OK and then Finish. D. BIOSTATION T2 NETWORK SETTINGS (Direct Network Connection to PC): 1. Statically set your PC running BioStar to the following address: a. IP Address: b. Gateway: c. Subnet: On the BioStation T2, click Menu. 3. Click Network. 4. Click TCP/IP. 5. Uncheck DHCP and enter the device s IP address to be Click the V arrow and enter as the Subnet. 7. In BioStar, click the Device menu tab. 8. Click Add Device (located under Tasks on the left side).
15 Page 15 Suprema Configuration Guide ACS OnSite Aparato 9. Select LAN and click Next. 10. Check the box for TCP. 11. Enter as the starting range. 12. Enter 16 as the ending range. 13. Click Next. 14. When the device is found, click Next.
16 Page 16 Suprema Configuration Guide ACS OnSite Aparato 15. Click on the checkbox next to the device, then click Add. 16. A dialogue box displaying 1 Device Added should appear. 17. Click OK and then Finish. E. BIOSTATION NETWORK SETTINGS (On Device Setup without BioStar): IMPORTANT: Setup an administrator password on the reader: On the device, click ESC > OK > Device > Master Password. Enter a secure admin password. Click OK. Press ESC back to the home screen. NOTE: This method only works with 26 bit Standard Wiegand with a FC Code of 0. Please use BioStar for any other configurations. 1. On the BioStation, press ESC. 2. Authenticate using an administrators Finger, PIN, or Card (If not administrator has been set, press the OK button). 3. Navigate to Network. 4. Navigate to TCP/IP. 5. Change DHCP to Not Use and enter the devices IP address to be (press the > arrow to add decimals). a. Enter as the Gateway. b. Enter as the Subnet. c. Press OK. 6. Select TCP/IP again.
17 Page 17 Suprema Configuration Guide ACS OnSite Aparato 7. Press F2. 8. Select BioStar for Server. 9. Enter the Server IP that you will use as the main Biometric Server for BioStar (Press the > for decimals. 10. Enter 8001 under the Port field. 11. Select Not Use for SSL. 12. Press OK twice. F. BIOSTATION NETWORK SETTINGS (Using a DHCP-Supported LAN): 1. Connect the BioStation to your LAN via Ethernet. 2. Ensure that the PC running BioStar is on the same subnet as the BioStation. 3. In BioStar, click the Device menu tab. 4. Click Add Device (located under Tasks on left side). 5. Select LAN, and then click Next. 6. Check the box for UDP and click Next.
18 Page 18 Suprema Configuration Guide ACS OnSite Aparato 7. Wait for the device to be found and then click Next (if the device was not found, ensure that the BioStation is on the same subnet as BioStar, or repeat Step 6 choosing TCP to search for a range of IP addresses). 8. Click the checkbox next to the device, then click Add. 9. A dialogue box 1 Device Added should appear. 10. Click OK and then Finish.
19 Page 19 Suprema Configuration Guide ACS OnSite Aparato G. BIOSTATION NETWORK SETTINGS (Direct Network Connection to PC): 1. Statically set your PC running BioStar to the following address: a. IP Address: b. Gateway: c. Subnet: On the BioStation, click ESC. 3. Authenticate using an administrators Finger, PIN, or Card (if no Administrator password has been set, press the OK button). 4. Navigate to Network. 5. Navigate to TCP/IP. 6. Change DHCP to Not Use and enter the devices IP address to be (press the > arrow to add decimals). a. Enter as the Gateway. b. Enter as the Subnet. c. Press OK. 7. In BioStar, click the Device menu tab. 8. Click Add Device (located under Tasks on the left side). 9. Select LAN and click Next. 10. Check the box for TCP. 11. Enter as the starting range. 12. Enter 16 as the ending range. 13. Click Next.
20 Page 20 Suprema Configuration Guide ACS OnSite Aparato 14. When the device is found, click Next. 15. Check the checkbox next to the device, and click the Add button. 16. A dialogue box 1 Device Added should appear. 17. Click OK and then Finish. H. BIOLITE NET NETWORK SETTINGS (USING A DHCP SUPPORTED LAN RECOMMENDED): 1. Connect the BioEntry Plus/BioEntry W to your LAN via Ethernet.
21 Page 21 Suprema Configuration Guide ACS OnSite Aparato 2. Ensure that the PC running BioStar is on the same subnet as the reader. 3. In BioStar, click the Device menu tab. 4. Click Add Device (located under Tasks on left side). 5. Select LAN and click Next. 6. Check the box for UDP and click Next. 7. Wait for the device to be found and then click Next (if the device was not found, ensure that the reader is on the same subnet as BioStar, or repeat Step 6 choosing TCP to search for a range of IP addresses).
22 Page 22 Suprema Configuration Guide ACS OnSite Aparato 8. Click the checkbox next to the device, then click Add. 9. A dialogue box 1 Device Added should appear. 10. Click OK and Finish. I. BIOLITE NET NETWORK SETTINGS (Direct Network Connection to PC): 1. Statically set your PC running BioStar to the following address: a. IP Address: b. Gateway: c. Subnet: On the BioLite Net, create your first administrator password. It is recommended to use the User ID of 1 and password This is temporary and will be removed automatically once connected to BioStar. 3. Press menu once at the BioLite Net home screen. 4. Enter your Admin ID and Password. 5. Move the right arrow to the Device icon, click OK. 6. Move the right arrow to I/O, click OK. 7. Move the right arrow to TCP/IP, click OK. 8. Enter as the IP address, (pressing the > arrow will enter decimals). Once finished, press OK. 9. Enter the as the subnet. 10. Enter as the gateway. 11. Use port Select Not Use when prompted for Server. 13. Select Not Support for 100-base T Support.
23 Page 23 Suprema Configuration Guide ACS OnSite Aparato 14. In BioStar, click the Device menu tab. 15. Click Add Device (located under Tasks on the left side). 16. Select LAN and click Next. 17. Check the box for TCP. 18. Enter Enter 16 as the ending range. 20. Click Next. 21. When the device is found, click Next.
24 Page 24 Suprema Configuration Guide ACS OnSite Aparato 22. Click the checkbox next to the device, then click Add. 23. A dialogue box 1 Device Added should appear. 24. Click OK and then Finish. 1.7 DEVICE CONFIGURATION TO COMMUNICATE WITH BRIVO CONTROLLER This section will explain how to configure the Suprema reader to communicate via Wiegand to a Brivo controller. A. Select your desired device from the device tree. B. Click the Wiegand tab and choose the desired Wiegand output next to the Wiegand In/Out prompt: 1. If Wiegand (user) out is chosen, there must be a user with a card number in the Brivo account that corresponds with a User ID in BioStar. 2. If Wiegand (card) out is chosen, there must be a user with a card number in the Brivo account that corresponds with a card number in a user profile in BioStar. C. Confirm the proper Wiegand bit format is configured, then click Apply. D. The reader is now ready to communicate to a Brivo controller, but it is recommended that you enroll and transfer a fingerprint to the BioEntry Plus for testing. You may then follow the steps for adding an Unknown Card found in the Brivo administrator manual for the appropriate platform being used.
25 Page 25 Suprema Configuration Guide ACS OnSite Aparato 1.8 CONFIGURING A CUSTOM WIEGAND FORMAT IN BIOSTAR A. Click the Wiegand tab. B. Click Change Format. This will open the Wiegand configuration wizard. C. Click a radio button to select one of the following options: 1. Click Change Format. This will open the Wiegand Configuration wizard. 2. Click a radio button to select one of the following options. a. 26-bit standard: This format is most widely used and consists of an 8-bit FC (facility code) and a 16-bit ID. You cannot change the bit definition of the format or the parity bits of this format. b. When configuring 26-bit, the only item you can customize is the FC code. To do this, follow through the wizard to the last page, and modify the FC Code under 26-bit Standard. D. Pass-through: Use this format to customize only the ID bits. During verification, if the ID is recognized, the Wiegand input string will pass through in its original form. You cannot set the parity bits or alternative values of this format. Non-ID bits are set to 0. E. Custom: With a custom format you can define the ID bits, parity bits, and alternative values.
26 Page 26 Suprema Configuration Guide ACS OnSite Aparato F. After selecting the format within the wizard, click Next to advance to the Format window. G. If desired, enter a new total number of bits and click Apply. H. Click the User ID button (I) on the right and assign ID bits by clicking the appropriate squares. I. Click the Even Parity button (E) on the right and assign an even parity bit by clicking the appropriate squares. J. Click the Odd Parity button (O) on the right and assign an even parity bit by clicking the appropriate squares. K. Click Next. L. In the Parity window, select the bits that will be used to calculate the first parity bit. M. As necessary, click the >> button and select the bits that will be used to calculate the additional parity bits. You must perform this step for each of the parity bits that you assigned in Steps 10 and 11. If necessary, you can click Initialize to reset the selection. N. Click Next. O. In the Alternative Value window, select a field to customize (non-id bits only).
27 Page 27 Suprema Configuration Guide ACS OnSite Aparato P. Click the Alt. Value checkbox and enter a new value for the output string. Q. Click Finish to close the wizard. R. Click Apply (Bottom right corner of BioStar Wiegand tab). 1.9 ENROLLING AND TRANSFERRING A USER TO A DEVICE A. Highlight User and then select Add New User under Task. B. Next on the Details tab provide a Name, ID and Start Date.
28 Page 28 Suprema Configuration Guide ACS OnSite Aparato C. Next on the Fingerprints tab select Scan. You will be prompted to Place Finger on Device, which will be repeated until you have a successful scan. You may also select Verification Test to confirm the fingerprint capture. D. Next under Tasks select Transfer All Users to Device. Check the desired device, then select the Transfer to Device button. You may now test the fingerprint and enroll and Unknown Card in the Brivo Aparato.
29 Page 29 Suprema Configuration Guide ACS OnSite Aparato NOTE: The Suprema reader(s) are now ready to communicate to the Brivo panel(s). Follow the general steps for adding reader devices and user IDs to the Brivo Aparato system.
SATO Network Interface Card Configuration Instructions
SATO Network Interface Card Configuration Instructions Table of Contents 1. Reset of wired/wireless interface card... 3 2. Installing the All-In-One Utility (recommended)... 4 3. Configuring wired/wireless
Deposit Direct. Getting Started Guide
Deposit Direct Getting Started Guide Table of Contents Before You Start... 3 Installing the Deposit Direct application for use with Microsoft Windows Vista... 4 Running Programs in Microsoft Windows Vista...
Configuring a Softphone for Windows for Virtual Contact Center
Configuring Bria 3 for Virtual Contact Center Configuring a Softphone for Windows for Virtual Contact Center 8x8 issues softphone licenses to Virtual Contact Center customers allowing them to manage all
Practice Management Installation Guide. Requirements/Prerequisites: Workstation Requirements. Page 1 of 5
Practice Management Installation Guide Your computers must meet the Workstation, Server and Network Requirements (see below for specifics). These requirements will ensure that Practice Management will
Wireless Setup Guide. Windows XP, Vista, 7 & 8
Wireless Setup Guide Windows XP, Vista, 7 & 8 At the end of this easy process, you will be able to operate your thermostat from any device that connects to the Internet Since you have already downloaded
atbusiness Deposit Installation Guide Table of Contents
Installation Guide atbusiness Deposit Installation Guide Table of Contents Merchant Installation Technical Requirements...3 Overview...4 Setup CAR...6 Download Device Driver...9 Merchant Capture Merchant
TECHNICAL BULLETIN. Configuring Wireless Settings in an i-stat 1 Wireless Analyzer
i-stat TECHNICAL BULLETIN Configuring Wireless Settings in an i-stat 1 Wireless Analyzer Before configuring wireless settings, please enable the wireless functionality by referring to the Technical Bulletin
Remote Deposit Capture Installation Guide
Remote Deposit Capture Installation Guide Please contact businessbanking@farmingtonbankct.com or call 860-284-6549 with any questions. Remote Deposit Capture Installation Instructions It is necessary to
Step by step guide for connecting PC to wired LAN at dormitories of University of Pardubice
Step by step guide for connecting PC to wired LAN at dormitories of University of Pardubice English version Version 1.1 July 2008 Information Cente University of Pardubice Content A. Windows XP... 2 B.
BioStar Config Guide V1.0
BioStar Config Guide V1.0 Suprema Inc. 16F Parkview Tower 6 Jeongja, Bundang Seongnam 463-863 Korea www.supremainc.com Last edited: 27 December 2011 This document is copyright 27 December 2011 by Suprema
Magaya Software Installation Guide
Magaya Software Installation Guide MAGAYA SOFTWARE INSTALLATION GUIDE INTRODUCTION Introduction This installation guide explains the system requirements for installing any Magaya software, the steps to
Ultra Thin Client TC-401 TC-402. Users s Guide
Ultra Thin Client TC-401 TC-402 Users s Guide CONTENT 1. OVERVIEW... 3 1.1 HARDWARE SPECIFICATION... 3 1.2 SOFTWARE OVERVIEW... 4 1.3 HARDWARE OVERVIEW...5 1.4 NETWORK CONNECTION... 7 2. INSTALLING THE
BioStar 1.8 Administrator Guide
f BioStar 1.8 Administrator Guide BioStar 1.8 Administrator Guide Suprema Warranty Policy... vii Disclaimers... vii Copyright Notice... viii 01 About the BioStar System... 9 1.1 Logical Configuration...
USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
Network Setup Guide. Introduction. Setting up for use over LAN
Network Setup Guide This manual contains the setup information required to use the machine over wired LAN. If you use the machine with USB connection, refer to your setup sheet. Introduction To use the
ATTENTION: End users should take note that Main Line Health has not verified within a Citrix
Subject: Citrix Remote Access using PhoneFactor Authentication ATTENTION: End users should take note that Main Line Health has not verified within a Citrix environment the image quality of clinical cal
BabyWare Imperial PC Software
Overview (see page 1) Things You Should Know (see page 1) Getting Started (see page 2) Licenses and Registration (see page 6) Usernames Passwords and Login (see page 7) BabyWare Imperial PC Software Overview
Installation and Connection Guide to the simulation environment GLOBAL VISION
Installation and Connection Guide to the simulation environment GLOBAL VISION Hardware and Software Requirements The following hardware specification is recommended for client machines: 2 GHz Pentium class
Connecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
V.I.P. Kit. Video Insight Pilot Kit. (Video Insight Pilot Kit).
V.I.P. Kit (Video Insight Pilot Kit). Video Insight Pilot Kit Please follow these instructions and everything should go very smoothly. Before you begin, you will need to establish (or obtain from your
Palm and Finger Vein Scanners
Palm and Finger Vein Scanners Finger and Palm Vein Readers work with ACS CheckPoint and ACS Headmaster Desktop and OnDemand. Models available for purchase 12740 Finger Vein Reader 12741 Palm Vein Reader
Easy Setup Guide for the Sony Network Camera
-878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer
Additional Requirements for ARES-G2 / RSA-G2. One Ethernet 10 Base T/100 Base TX network card required for communication with the instrument.
TA Instruments TRIOS Software Installation Instructions Installation Requirements Your TRIOS Instrument Control software includes all the components necessary to install or update the TRIOS software, as
JKW-IP. IP Video Entry System. QuikStart Guide
1210 JKW-IP IP Video Entry System QuikStart Guide This is an abbreviated instruction manual for installation purposes. Please see the JKW-IP Installation Manual and JKW-IP Operation Manual for complete
To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:
PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,
2 Setting Up the Hardware for a Wired Ethernet Network... 13. 3 Setting Up the Software for an Ethernet Network... 21
Contents 1 Networking Basics............................................... 1 Selecting a network connection........................................ 2 Wired Ethernet network...........................................
Avigilon Control Center Server User Guide
Avigilon Control Center Server User Guide Version 4.10 PDF-SERVER-D-Rev1 Copyright 2011 Avigilon. All rights reserved. The information presented is subject to change without notice. No copying, distribution,
BioStar 1.8 Administrator Guide
BioStar 1.8 Administrator Guide EN 102.00.BS V1.8A BioStar 1.8 Administrator Guide Suprema Warranty Policy... vii Disclaimers... vii Copyright Notice... viii 01 About the BioStar System... 9 1.1 Logical
TE100-P21/TEW-P21G Windows 7 Installation Instruction
Hardware Installation TE100-P21/TEW-P21G Windows 7 Installation Instruction 1. Go to http://www.trendnet.com/downloads/ to download the Windows 7 Utility. Save the file to your desktop. 2. Right click
Point of Sale 2015 Enterprise. Installation Guide
Point of Sale 2015 Enterprise Installation Guide Contents About this guide 3 System Requirements - Microsoft SQL Server 2008 R2 Express 3 System Requirements - POS Enterprise 2015 (Administrator) 3 System
Allworx OfficeSafe Operations Guide Release 6.0
Allworx OfficeSafe Operations Guide Release 6.0 No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy,
ENTBUS PLUS SOFTWARE FOR ENERGY MONITORING AND RECORDING INSTALLATION AND OPERATING MANUAL
ENTBUS PLUS SOFTWARE FOR ENERGY MONITORING AND RECORDING INSTALLATION AND OPERATING MANUAL Foreword Entbus services manage the collection of information and storing this information in the database. Services
AXIS Camera Station Quick Installation Guide
AXIS Camera Station Quick Installation Guide Copyright Axis Communications AB April 2005 Rev. 3.5 Part Number 23997 1 Table of Contents Regulatory Information.................................. 3 AXIS Camera
User Guide for Windows 10
User Guide for Windows 10 System requirements E10684 First Edition July 2015 To facilitate a smoother transition from your previous operating system, read the system requirements below before upgrading
LOREX CLIENT 2.2 Integrated Remote Agent Software
LOREX CLIENT 2.2 Integrated Remote Agent Software Instruction Manual English Version 1.0 MODEL: L15LD420 / L17LD420 Series Copyright 2008 LOREX Technology Inc. www.lorexcctv.com Table of Contents Table
Contents. Section A Networking Basics... 1. 1 Learning the Basics... 3. Section B Wired Ethernet Networking... 17
Contents Section A Networking Basics...................................... 1 1 Learning the Basics............................................. 3 Selecting a network connection........................................
CRM Outlook Plugin Installation
CRM Outlook Plugin Installation Last Modified on 01/15/2016 4:51 pm EST Hardware Requirements Component Minimum Recommended Processor Intel Pentium III 750-MHz CPU, or comparable Dual-core 1.8-GHz CPU
Clock Link Installation Guide. Detailed brief on installing Clock Link
Clock Link Installation Guide Detailed brief on installing Clock Link 1 Table of Contents 1. Overview... 3 2. Configuring the Time Clock... 3 Instructions:... 3 2.1 IP Address Setup... 3 2.2 Subnet Mask
Manual Wireless Extender Setup Instructions. Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key
1 Manual Wireless Extender Setup Instructions Before you start, there are two things you will need. 1. Laptop computer 2. Router s security key Setting up LAN Static IP on PC We need to set up a Static
Fiery E100 Color Server. Welcome
Fiery E100 Color Server Welcome 2011 Electronics For Imaging, Inc. The information in this publication is covered under Legal Notices for this product. 45098226 27 June 2011 WELCOME 3 WELCOME This Welcome
BASLER ACE QUICK INSTALLATION GUIDE
BASLER ACE QUICK INSTALLATION GUIDE Rev. 01 Quick installation Guide V1 1 Introduction The installation procedures in this guide assume that you want to get your camera operational and begin capturing
SOP085 - HELLER OVEN SOFTWARE INSTALLATION PROCEDURE. For version 6.2.x.x
SOP085 - HELLER OVEN SOFTWARE INSTALLATION PROCEDURE For version 6.2.x.x DATE REV ECN - DESCRIPTION OF CHANGE Initials 02/20/2014 INT ECN 140003-001 TP For version 6.2.x.x Rev. INT Page 1 of 16 Basic PC
WorldExtend IronDoor 3.5 Publishing a Terminal Services Application
WorldExtend IronDoor 3.5 Publishing a Terminal Services Application WorldExtend, LLC. Published: September 2008 Abstract This guide will walk you through the steps required to publish a terminal services
Using the ievo fingerprint reader with Net2
Using the ievo fingerprint reader with How does it work? The ievo system stores the encoded fingerprint information within each reader. Once registered on the enrolment reader, the fingerprint data is
Preparing the Windows version of the software for use
Preparing the Windows version of the software for use System requirements Component Processor RAM Hard disk Drives Interfaces/network TCP/IP internet protocol Screen Installing the Conference Manager software
OUTDOOR IR NETWORK CAMERA Series
OUTDOOR IR NETWORK CAMERA Series INSTALLATION GUIDE Please read instructions thoroughly before operation and retain it for future reference. 1. OVERVIEW 1.1 Package Content Network camera Installation
1. Central Monitoring System Software
1. Central Monitoring System Software 1-1. General information CMS program is an application with which users not only watch and control remote DVRs, but also receive video/audio data or alarm signals
CMP-102U. Quick Installation Guide
CMP-102U Quick Installation Guide V1.0 http://www.cnet.com.tw 1 CMP-102U Supports One High-speed USB2.0 Port MFP Server Supports 10/100Mbps Fast Ethernet Network Quick Installation Guide 1 Package Contents:
X Series Application Note 43:
X Series Application Note 43: Using the Remote Viewing & Web Pages of the X - Series & GR Series Recorders The Remote Viewing function of the X-Series and GR Series Recorders provide the user with the
OfficeSuite CRM Connector Quick Start-Up Guide Version 1.0 May 2013
OfficeSuite CRM Connector Quick Start-Up Guide Version 1.0 May 2013 i Table of Contents INTRODUCTION AND GETTING STARTED... 1 OPERATING SYSTEM, HARDWARE AND SOFTWARE REQUIREMENTS... 1 Hardware Requirements...
The following sections describe the Gateway configuration pages in the SBG1000 Setup Program.
Configuration Gateway > WAN Page Gateway: LAN nat config Page Gateway: LAN dhcp server config Page Gateway LOG Page Preparing the Network Preparing the Computers for TCP/IP Networking Configuring TCP/IP
LockView 4.3.1 CompX Database & Network Configuration & Installation Manual
LockView 4.3.1 CompX Database & Network Configuration & Installation Manual Table of Contents CompX Database & Network Configuration & Installation Manual Introduction... 4 Installation Requirements...
IP-Pro (Virtual IP Protocol Independent Version) User Instructions
IP-Pro (Virtual IP Protocol Independent Version) User Instructions - Table of Contents - 1. IP Pro introduction 2. IP Pro installation 3. IP Pro setup 4. Virtual IP function check 5. Virtual IP changes
DIAGNOSTICLINK 8.02 ORDERING SYSTEM
DIAGNOSTICLINK 8.02 ORDERING SYSTEM Version 1.4 4/27/2015 TABLE OF CONTENTS 1 INTRODUCTION...4 1.1 Purpose of Ordering System Guide...4 2 SYSTEM REQUIREMENTS...4 2.1 Minimum Requirements...4 3 ORDER SYSTEM...4
XStream Remote Control: Configuring DCOM Connectivity
XStream Remote Control: Configuring DCOM Connectivity APPLICATION BRIEF March 2009 Summary The application running the graphical user interface of LeCroy Windows-based oscilloscopes is a COM Automation
User Manual. Onsight Management Suite Version 5.1. Another Innovation by Librestream
User Manual Onsight Management Suite Version 5.1 Another Innovation by Librestream Doc #: 400075-06 May 2012 Information in this document is subject to change without notice. Reproduction in any manner
DSL Self-install Kit Instructions
DSL Self-install Kit Instructions Cover and installation notes Page 1 1. Verify your system requirements Page 2 2. Verify the contents of your DSL Self-Install kit Page 2 3. Install filters on your telephone
NetLINE Wireless Broadband Gateway
NetLINE Setup Guide Farallon s NetLINE connects to your cable/dsl modem, allowing computers on your local wired and wireless networks to share a single broadband connection to the Internet. This Setup
Enterprise Site Manager (ESM) & Administrator Console Installation / Uninstall
Enterprise Site Manager (ESM) & Administrator Console Installation / Uninstall July 2013 For further information visit our support page: www.pearsonwbl.edexcel.com/our-support 1 Contents Please note clicking
Topaz Installation Sheet
Topaz Installation Sheet P/N 460924001E ISS 08FEB12 Content Introduction... 3 Recommended minimum requirements... 3 Setup for Internet Explorer:... 4 Topaz installation... 10 Technical support... 14 Copyright
1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
Cisco - Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW)
Page 1 of 20 Configure the 1721 Router for VLANs Using a Switch Module (WIC-4ESW) Document ID: 50036 Contents Introduction Prerequisites Requirements Components Used Network Diagram The Role of Switched
PREMIUM BUSINESS GATEWAY - DEVG2020 DIGITAL BUSINESS USER GUIDE
PREMIUM BUSINESS GATEWAY - DEVG2020 DIGITAL BUSINESS USER GUIDE NEED MORE SUPPORT? If you have questions beyond this guide, we want to help. To learn more about your Business Broadband or Digital Business
1. Central Monitoring System Software
1. Central Monitoring System Software 1-1. General information CMS program is an application with which users not only watch and control remote DVRs, but also receive video/audio data or alarm signals
Installation and Configuration of Aadhaar Enrolment Client
Installation and Configuration of Aadhaar Enrolment Client UIDAI Unique Identification Authority of India Version: 2.0.0.2 Release date: 27-11-2012 Preface This training manual contains the detailed steps
Virtual Appliance Setup Guide
The Barracuda SSL VPN Vx Virtual Appliance includes the same powerful technology and simple Web based user interface found on the Barracuda SSL VPN hardware appliance. It is designed for easy deployment
Freshservice Discovery Probe User Guide
Freshservice Discovery Probe User Guide 1. What is Freshservice Discovery Probe? 1.1 What details does Probe fetch? 1.2 How does Probe fetch the information? 2. What are the minimum system requirements
Email client configuration guide. Business Email
Email client configuration guide Business Email August 2013 Contents 1. Mac Email Clients 1.1 Downloading Microsoft Outlook (Professional Plan Users) 1.2 Configuring Microsoft Outlook (Full Exchange Server
Trax Attendance Manager Full Installation (Windows XP, 32 bit Windows Vista, or 32 bit Windows 7)
Trax Attendance Manager Full Installation (Windows XP, 32 bit Windows Vista, or 32 bit Windows 7) NOTE: There are separate instructions for 64 bit Windows Vista, 64 bit Windows 7, and clients in Canada.
Lab 8.4.5.1 Configuring LEAP/EAP using Local RADIUS Authentication
Lab 8.4.5.1 Configuring LEAP/EAP using Local RADIUS Authentication Objective Topology Estimated Time: 40 minutes Number of Team Members: Students can work in teams of two. In this lab, the student will
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM
STATIC IP SET UP GUIDE VERIZON 7500 WIRELESS ROUTER/MODEM Verizon High Speed Internet for Business Verizon High Speed Internet for Business SETTING UP YOUR NEW STATIC IP CONNECTION AND IP ADDRESS(ES) This
Intel Active Management Technology with System Defense Feature Quick Start Guide
Intel Active Management Technology with System Defense Feature Quick Start Guide Introduction...3 Basic Functions... 3 System Requirements... 3 Configuring the Client System...4 Intel Management Engine
You may refer the Quick Installation Guide in the package box for more information.
Hardware Installation: 1. Turn off your modem. 2. Use one Ethernet cable to connect your modem to WAN port (Blue) port of BR-6228nC. 3. Use another Ethernet cable to connect your PC to one LAN Port (Yellow)
Configuring an A Series LED Sign Controller for your Network
Configuring an A Series LED Sign Controller for your Network A Series LED displays from Optec support both serial and 10BaseT Ethernet communication. Serial communication via RS232 or RS485 is independent
EnGenius ERB9250 300M Range Extender. Quick Start Guide
EnGenius ERB9250 300M Range Extender Quick Start Guide Package Contents One ERB9250 300M Range Extender One 12V/1A power adapter Two 2dBi 2.4GHz SMA antennas One Ethernet cable One CD-ROM with user s manual
EASE Scan Tool Customers. SECTION I - Installation
Please Install Your EASE Scan Tool DVD Before Installing Any Other Software That Came With Your Package. SECTION I - Installation ATTENTION: Do NOT connect an EASE Vehicle Interface Device to your Computer
How To Connect To A University Of Cyprus Vpn 3000 From Your Computer To A Computer With A Password Protected Connection
VPN 3000 Client for Windows XP & VISTA Information Security office University Of Cyprus October 11, 2007 Table of Contents 1. What is VPN 3000? 2. How To Use VPN 3000 3. Installing the VPN 3000 Client
Nexio Connectus with Nexio G-Scribe
Nexio Connectus with Nexio G-Scribe 2.1.2 3/20/2014 Edition: A 2.1.2 Publication Information 2014 Imagine Communications. Proprietary and Confidential. Imagine Communications considers this document and
Cloud Services ADM. Agent Deployment Guide
Cloud Services ADM Agent Deployment Guide 10/15/2014 CONTENTS System Requirements... 1 Hardware Requirements... 1 Installation... 2 SQL Connection... 4 AD Mgmt Agent... 5 MMC... 7 Service... 8 License
Andover Continuum Remote Communication Configuration Guide
Andover Continuum Remote Communication Configuration Guide 2010, Schneider Electric All Rights Reserved No part of this publication may be reproduced, read or stored in a retrieval system, or transmitted,
Windows Vista /Windows 7 Installation Guide
Windows Vista / 7 Installation Guide Before you can use the machine, you must set up the hardware and install the driver. Please read the Quick Setup Guide and this Windows Vista / 7 Installation Guide
Table of Contents. Chapter1. Introduction...1. 1.1 Before Installation... 1 1.2 System Requirements... 1
Table of Contents Chapter1. Introduction...1 1.1 Before Installation... 1 1.2 System Requirements... 1 Chapter2. IVS-110 1-Channel Internet Video Server...2 2.1 Package Content... 2 2.2 Physical Installation...
Windows Server 2008 R2 Initial Configuration Tasks
Windows Server 2008 R2 Initial Configuration Tasks I am not responsible for your actions or their outcomes, in any way, while reading and/or implementing this tutorial. I will not provide support for the
Internet Setup Manual for Windows 95/98
Step 1 On your Windows 95/ 98 desktop, click on Start, then click on Settings, then click on Control Panel. Step 2 Inside of the Control Panel, find the icon labeled Network. Now double-click on the Network
WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014
WRE6505 Wireless AC750 Range Extender Version 1.00 Edition 1, 4 2014 2.4G 5G Quick Start Guide User s Guide Default Login Details LAN IP Address 192.168.1.2 User Name admin www.zyxel.com Password 1234
MySupport. End User Guide. Document Version: 1.3
MySupport End User Guide Document Table of Contents Table of Contents... 2 Introduction... 3 What is MySupport?...3 System Requirements...3 MySupport Application... 4 Installing MySupport... 4 System Tests...5
Table of Contents. Introduction...9. Installation...17. Program Tour...31. The Program Components...10 Main Program Features...11
2011 AdRem Software, Inc. This document is written by AdRem Software and represents the views and opinions of AdRem Software regarding its content, as of the date the document was issued. The information
Basic Mercury Powered NXT Configuration in Doors.NET TM Application Note. 1.0 Adding an NXT-MSC Controller to the NXT Gateway
Doors.NET installation and controller configuration is a three step process. Each of these steps has its own document, with controller configuration broken into separate documents per hardware type. software
Comodo LoginPro Software Version 1.5
Comodo LoginPro Software Version 1.5 User Guide Guide Version 1.5.030513 Comodo Security Solutions 1255 Broad Street STE 100 Clifton, NJ 07013 Table of Contents 1.Introduction to Comodo LoginPro... 3 1.1.System
Network Scanner Tool R3.1. User s Guide Version 3.0.04
Network Scanner Tool R3.1 User s Guide Version 3.0.04 Copyright 2000-2004 by Sharp Corporation. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited,
Network Video Recorder. User s Manual v1.0.0. Model: SVR-504/508/516/516+
User s Manual v1.0.0 Model: SVR-504/508/516/516+ Table of Contents Product Description 6 Install Hard Disk 7 Hardware Illustration 10 I/O Ports and RS-485 12 LEDs Definition 13 Connect to the NVR 15 2
SupportDesk Extensions Installation Guide Extension Service - Versions 6.9 8.5
SupportDesk Extensions Installation Guide Extension Service - Versions 6.9 8.5 Richmond Systems Ltd, West House, West Street, Haslemere, Surrey, GU27 2AB Tel: +44 (0)1428 641616 - Fax: +44 (0)1428 641717
Step-by-Step Setup Guide Wireless File Transmitter FTP Mode
EOS Step-by-Step Setup Guide Wireless File Transmitter FTP Mode Ad Hoc Setup Windows XP 2012 Canon U.S.A., Inc. All Rights Reserved. Reproduction in whole or in part without permission is prohibited. 1
How To Install Sedar On A Workstation
SEDAR Client Installation Guide Version 1.2 January 27, 2014 10 Contents About This Guide... 2 Assumptions... 3 Date Format Synchronization... 3 Before You Begin the Installation Test of the SEDAR Client...
Qvis Security Technical Support Field Manual LX Series
Table of Contents Page 1: Motion Detection 1.0 Configuring Motion Detection for LX Apollo / LX Zeus DVRs 2 1.1 Motion Playback on LX Apollo / LX Zeus DVRs 3 1.2 Scheduling Motion and Continuous Recording
Use this guide if you are no longer able to scan to Sharpdesk. Begin with section 1 (easiest) and complete all sections only if necessary.
Use this guide if you are no longer able to scan to Sharpdesk Instructions: Begin with section 1 (easiest) and complete all sections only if necessary. 1 Section 1 Complete pages 3-5. Scan to the desired
AVG 8.5 Anti-Virus Network Edition
AVG 8.5 Anti-Virus Network Edition User Manual Document revision 85.2 (23. 4. 2009) Copyright AVG Technologies CZ, s.r.o. All rights reserved. All other trademarks are the property of their respective
Network Setup Guide. 1 Glossary. 2 Operation. 1.1 Static IP. 1.2 Point-to-Point Protocol over Ethernet (PPPoE)
Network Setup Guide 1 Glossary 1.1 Static IP Computers are communicated and recognized by their own unique IP addresses over the Internet. Static IP provided by your ISP (Internet Service Provider) means
Web Manual: Email October 2015
Table of Contents Getting Started... 3 How to change your password... 3 How to Access Division Email... 4 Outlook Web App (Webmail)... 4 iphone... 4 Android... 4 Blackberry... 4 Outlook Anywhere (MS Outlook)
Guide to Installing BBL Crystal MIND on Windows 7
Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP