Mask Information Guide

Transcription

1 Mask Information Guide

2 Welcome to your handy guide to ResMed masks Here you ll find mask selection information, fitting guides, product codes, product features and benefits for the full range of ResMed mask systems - pillows, nasal, full face, non-vented and disposable. Only from ResMed - world leaders in mask technology. contents SELECTING A MASK NASAL PILLOWS NASAL MASKS FULL FACE MASKS NON-VENTED MASKS DISPOSABLE MASKS TECHNICAL SPECIFICATIONS Mask/Device Compatibility USE AND CARE

3 Mask Type 1 Past nasal / soft palate surgery (e.g. UPPP)? NO YES Selection Select the appropriate mask type by following the flow diagram on the right. Ideally, the patient should choose their preferred mask with clinical guidance. 2 Rhinitus? Sinusitis? Hay Fever? NO YES No Humidifier YES With Humidifier Useful tips A full face mask is preferable for patients with mouth leak. 3 Other nasal symptoms (e.g. Mouth breathes)? NO YES If a full face is not required, a nasal system should be first choice. Pillows should be considered as the nasal mask of choice. 4 Claustrophobic? Skin conditions / allergies? NO YES Swift TM LT 5 Active sleep? Poor fit in past / present? YES Mirage Activa TM LT NO Mirage Quattro TM OR Swift LT OR Mirage Activa LT Mirage Liberty TM OR Mirage Micro TM SELECTING A MASK

4 Mask Size Selection Select the appropriate mask size by following the instructions. The range of sizes ensures that every patient can achieve optimal fit. Useful tips The 2D sizing templates will help you determine the optimal cushion size. If the template opening is too close to their nares or nasal perimeter, that size cushion is incorrect and may cause the patient to experience discomfort from pressure on the nasal bridge or cheek bones. Incorrect cushion size can also lead to leak into the eyes or around the nose. SELECTING A MASK

5 Mask Size Mirage Micro NASAL MASK Mirage Activa LT NASAL MASK Ultra Mirage TM NASAL MASK II Mirage Activa NASAL MASK Place the fitting template around the nose and align arrow to bottom of the nose. Obtain a close fit around the nose allowing some clearance around the nostrils and the nasal bridge. SELECTING A MASK

6 Mask Size Mirage Quattro FULL FACE MASK Align the fitting template to chin crease. Determine cushion size according to the position of the corner of the eye. Mirage Liberty FULL FACE MASK Align the fitting template to bottom of the nose. Check the position of the chin crease above or below the dotted line. If the chin crease is above dotted line, then choose the small cushion. If the chin crease is below dotted line, then choose the large cushion. SELECTING A MASK

7 Complete mask system Tube retainer (optional) Top buckle/s (1) (10) Frame Back buckle/s (1) (10) Short tube assembly (short tube, elbow and swivel) Pillows (XS) (S) (M) (L) Headgear assembly (headgear, buckles) Product packed with S, M and L pillows. XS sold separately. NASAL PILLOWS

8 Quick fitting guide Minimal contact, optimal seal The first nasal pillows with ResMed s proven dual-wall technology. The pillows rest on a flexible cushion base maintaining seal. Freedom to move and sleep on the side Headgear with flexible stabilising elements gently holds the system in place when user turns or moves during sleep. The cushion base enables the dual-wall pillows to move in different directions without compromising seal or creating leaks. Super-quiet and personalised comfort Air is dispersed gently through the fine vents. The innovative vent design directs air away from the user and their partner Holding the pillows at your nose, pull the headgear over your head. Headgear should sit midway between the ears and eyes. 4 5 Using the click-fit adjustor, position the nasal pillows at the most suitable angle. Connect the Swift LT short tube to the device air tubing. Turn on the device. Adjust the top straps by pulling them evenly until comfortable. Do not overtighten. The Swift LT is now fitted and ready for use. Do not overtighten headgear straps Repeat Step 2 with the back straps. Do not overtighten. Optional For alternate tubing positions, use the tube retainer. To attach, push it into the top headgear buckle. Clip in either the short tube or device air tubing, depending on flexibility needs. The tubing can be positioned to either side of your face or centered. If the pillows pull on your nose, adjust the tubing at the tube retainer. NASAL PILLOWS

9 Complete mask system Pillow sleeve (S) (M) (L) Short tube assembly/ies (1) (10) Frame system (no headgear) (S) (M) (L) Tube retainer (3) Distal pressure part (1) (10) Headgear buckles (4) Headgear Clip Frame with clip and cap Seal rings (10) 1 Product packed with S, M & L pillows. Cap NASAL PILLOWS

10 Dial Forehead support Forehead pad/s (1) (10) Headgear (S) (Std) (L) 3 Elbow assembly Ports cap (2) (10) Mask cushion (S) (M) (L) (LW) (XL) Elbow Swivel Mask frame (Std) (S) 1 Headgear clips (2) (10) 1 Small cushion and frame are only compatible with each other. 2 Standard headgear supplied with all sizes of complete mask assembly. Small Medium Large Large-Wide Extra-Large 3 Small (16118) and Large (16119) headgear come without clips NASAL MASKS

11 Quick fitting guide Intuitively easy Easy removal of cushion and elbow from frame (no cushion or elbow clip). Easy one-hand adjustment of the forehead support with the MicroFit dial Personalised fit and comfort Allows for optimum, accurate fit with a turn of the MicroFit dial. Mirage Micro dual-wall cushions now come in five sizes, to fit 95% of patients 1. Turn MicroFit dial to position 24. Disconnect one headgear clip. Place mask on face, slide headgear on. Reconnect lower headgear clip. Quiet, sleek and stylish Quieter than a soft whisper. Less obtrusive with minimalist forehead support. 1 Based on internal anthropometric database (n=267) Unfasten upper tabs, pull until comfortable. Reattach the tabs. Repeat step 4 with lower straps. Connect tube to mask and flow generator. Start flow generator. Turn MicroFit dial to eliminate leaks. Do not overtighten headgear straps NASAL MASKS

12 Forehead support pad/s (1) (10) Dial Forehead support Mask frame Mask cushion and clip (M) (L) (LW) Elbow Elbow assembly (elbow, swivel): Swivel Clip Ports cap (2) (10) Headgear clips (2) (10) Headgear (S) (Std) (L) 2 Medium Large Large-Wide 1 Standard headgear supplied with all sizes of complete mask assembly. 2 Small (16118) and Large (16119) headgear come without clips NASAL MASKS

13 Quick fitting guide ActiveCell Technology The unique cushion features an active cell that automatically expands and contracts to suit user movements and varying pressures throughout the night. Ideal for active sleepers; ActiveCell Technology provides dynamic defence against leak. A fine-tuned fit MicroFit dial provides easy, one-handed forehead support adjustment. Less dependant on headgear tension and adjustment to achieve an effective seal (quicker fitting time, less callbacks and improved user compliance). The quiet achiever Innovative diffuse vent design, disperses air quietly and softly, at a short distance, away from the bed partner. Located on the elbow for easy cleaning and disassembly. Do not overtighten headgear straps Turn the MicroFit dial to position 24, so that the forehead support is fully extended Allow room for the cushion s active cell to inflate. Use two fingers as a guide. Disconnect the lower headgear clip, hold the mask over the nose and pull the headgear over the head. Reconnect the lower headgear clip ensuring it clicks into place. Turn on the airflow device. If the mask is fitted correctly, the cushion should be smooth and the active cell (highlighted) fully inflated. Connect one end of the air tubing to the swivel and the other end to the airflow device. While lying down, adjust the dial for comfort and seal. If fitted incorrectly, the cushion will be creased and the active cell underinflated. NASAL MASKS

14 Headgear (S) (Std) (L) 3 Elbow clip (10) Frame Frame assembly (no cushion and headgear) Forehead support with pads Forehead pad/s (1) (10) Cushion (Std) (L) (Sh) (Sh-W) Vent cover Elbow assembly Swivel Ports cap (2) (10) Headgear clips (2) (10) Cushion clip Complete mask system comes with standard sized headgear. 2 Elbow assembly includes elbow clip, vent cover, elbow and swivel. 3 Small (16118) and Large (16119) headgear come without clips. Standard Large Shallow Shallow-Wide NASAL MASKS

15 Quick fitting guide Seal and comfort Mirage dual-wall cushion reduces pressure on nasal bridge and optimises seal and comfort. Forehead support provides seal and stability with a choice of four clearly numbered positions. Easy to use Headgear clips allow quick attachment/ detachment of headgear - no further adjustments required after initial fitting Disconnect one headgear clip. Ensure that forehead support tab is in position 1. Place mask on face and pull headgear over head. Make sure upper straps pass across forehead and lower straps below ears. Reattach headgear clip to mask frame. Gently tighten upper headgear straps. The forehead support pads should lightly touch the forehead. Do not overtighten straps. Gently tighten lower headgear straps. Do not overtighten straps. Ultra-quiet Vent design minimises airflow intensity and noise. Specially designed to direct air away from user and partner, and provide optimum CO 2 washout. 1 Based on internal anthropometric database (n=267) Connect one end of air tubing to mask swivel and other end to flow generator. Turn flow generator on. If air leaks around cushion you may need to make some adjustments. In this case, proceed to step 5. Loosen upper headgear straps and move forehead support tab to another position (eg, position 2). Gently tighten upper headgear straps. Test all four positions of forehead support tab and adjust headgear straps until you achieve a secure and comfortable fit. Do not overtighten headgear straps NASAL MASKS

16 Forehead pad/s (1) (10) Mask frame Forehead support Elbow assembly (including exhaust vent) Cushion (Std) (L) (Sh) Inlet tube and swivel assembly (1) (10) Ports caps (2) (10) Headgear clip/s (2) (10) Cushion clip Headgear (Including headgear clips) (S) (Std) (L) 1 Swivel assembly (10) 1 Small (16118) and Large (16119) headgear come without clips. 2 Standard headgear supplied with all sizes of complete mask assembly. Standard Large Shallow NASAL MASKS

17 Unobtrusive design Age 7 or over Headgear Headgear clips Cushion Elbow assembly 1 Frame (Std) (2), (10) (Std), (Dp) Crossover buckle Cushion 2 Headgear 2 Headgear clips (1), (10) (S) (S) (2), (10) Standard Deep Small These parts are common with the Kidsta. 2 The cushion and headgear on the Kidsta can be used with the Vista. NASAL MASKS

18 1 Ultra Mirage NV FULL FACE MASK Effective and comfortable 3 Ultra Mirage NV NASAL MASK A more unobtrusive option for NIV Frame (S) (M) (L) Elbow Headgear Elbow assembly Frame Forehead support Forehead pad/s (2) (10) Tube connector/s (1) (10) S-Std M-Std L-Std Standard Large Shallow S-Sh M-Sh L-Sh Common parts with Ultra Mirage Full Face Mask: forehead pads, headgear clips, cushion & clips,elbow retainer, forhead support and ports caps. 2 This part is common with Ultra Mirage Nasal Mask NV. 3 Common parts with Ultra Mirage II: cushion & clip, elbow clip, headgear clips & ports cap. NON-VENTED MASKS

19 Disposable NASAL MASK A more unobtrusive option for NIV Disposable FULL FACE MASK Easy to seal Headgear (10) Medium Large Small Medium Large Disposable NV FULL FACE MASK For use with a leak circuit Headgear (10) Small Medium Large DISPOSABLE MASKS

20 Technical Specifications Ultra Mirage II Nasal Mirage Quattro, Mirage Liberty, Ultra Mirage, Hospital Full Face Mask Mirage Swift II Nasal Pillows Swift LT Nasal Pillows TECHNICAL SPECIFICATIONS

21 Mask Device Compatibility The table below specifies the masks compatible with ResMed s positive airway pressure devices and the mask setting, if one is required. For full details regarding the correct use of these devices, please refer to the specific User Guides. Nasal Pillows Mirage Swift II Swift LT S7 AutoSet Spirit MIRAGE MIRAGE S8 AutoSet Spirit II SWIFT SWIFT S8 Escape II No setting required. Consult your clinician before changing to a different mask type. VPAP III Series MIRAGE MIRAGE AutoSet CS 2 N/V N/V N/V = The mask has not been validated for this device. Mask Device Compatibility

22 Mask Device Compatibility The table below specifies the masks compatible with ResMed s positive airway pressure devices and the mask setting, if one is required. For full details regarding the correct use of these devices, please refer to the specific User Guides. Nasal Masks Mirage Micro Ultra Mirage II Activa LT Mirage Activa Mirage Vista Mirage Kidsta S7 AutoSet Spirit STANDARD ULTRA STANDARD STANDARD STANDARD STANDARD S8 AutoSet Spirit II STANDARD ULTRA ACTIVA ACTIVA STANDARD STANDARD S8 Escape II No setting required. Consult your clinician before changing to a different mask type. VPAP III Series STANDARD ULTRA STANDARD STANDARD STANDARD STANDARD AutoSet CS 2 VISTA ULTRA ACTIVA ACTIVA VISTA N/V N/V = The mask has not been validated for this device. Mask Device Compatibility

23 Mask Device Compatibility The table below specifies the masks compatible with ResMed s positive airway pressure devices and the mask setting, if one is required. For full details regarding the correct use of these devices, please refer to the specific User Guides. Full Face Masks Mirage Quattro Mirage Liberty Ultra Mirage S7 AutoSet Spirit MIR FULL MIR FULL MIR FULL S8 AutoSet Spirit II MIR FULL MIR FULL MIR FULL S8 Escape II No setting required. Consult your clinician before changing to a different mask type. VPAP III Series MIR FULL MIR FULL MIR FULL AutoSet CS 2 FULL FACE FULL FACE FULL FACE Mask Device Compatibility

24 Mask Device Compatibility The table below specifies the masks compatible with ResMed s positive airway pressure devices and the mask setting, if one is required. For full details regarding the correct use of these devices, please refer to the specific User Guides. Disposable Masks Hospital Nasal Hospital Full Face S7 AutoSet Spirit STANDARD MIR FULL S8 AutoSet Spirit II STANDARD MIR FULL S8 Escape II No setting required. Consult your clinician before changing to a different mask type. VPAP III Series N/V MIR FULL AutoSet CS 2 VISTA FULL FACE N/V = The mask has not been validated for this device. Mask Device Compatibility

25 Use and Care GUIDE CLEANING Daily The cushion and frame should be wiped daily with a damp cloth. Weekly The mask system should be washed a minimum of once per week. Separate and hand wash mask components (including tubing) in lukewarm, soapy water (original washing up liquid is recommended). Rinse well and allow to air dry out of direct sunlight, not on a radiator. Hand-wash headgear separately. Caution Do not use solutions containing bleach, chlorine, alcohol, aromatics, moisturisers, antibacterial agents or scented oils to clean the mask or tubing. These solutions may reduce the life of the mask (life expectancy is 1 year). If any visible deterioration of a mask component is apparent (cracking, crazing, tears, etc), the mask component should be discarded and replaced. DISINFECTION Validated disinfection / sterilisation procedures High level thermal disinfection. High level chemical disinfection. STERRAD sterilisation. Parts that cannot be disinfected / sterilised Swivel, short tubing Mirage (vented & non-vented) Nasal Mask. Swivel, inlet tube Mirage Activa, Kidsta, Vista Nasal Masks & Liberty Full Face Mask. Valve membrane Mirage Nasal Mask, Mirage S2 & Ultra Mirage Full Face Mask. All components, excluding the above, can be recycled over 15 times. The Mirage Quattro, Mirage Liberty and Mirage Micro can be recycled over 20 times. Further detailed information can be found on USE AND CARE