7" Portable HDMI Monitor
|
|
- Gavin Norman
- 1 years ago
- Views:
Transcription
1 7" Portable HDMI Monitor Created by Ruiz Brothers Last updated on :10:09 PM EDT
2 Guide Contents Guide Contents Overview DIY Monitor Connect to a Raspberry pi Use as a second monitor Camera preview monitor Prerequisite Guides Parts Tools & Supplies Circuit Diagram The Circuit Diagram 3D Printing Customize Design Materials Tolerances Bed Leveling Clean up Assembly Wire length Bend slide switch leads Tin and solder switch Heat shrink Mount slide switch Tin and solder monitor pads Solder PowerBoost Connect Slide Switch Mount PowerBoost Mount monitor Attach Battery 1/4-20 Tripod screw Camera battery powered Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 2 of 18
3 Overview DIY Monitor In this project, we're going to make a DIY monitor using an 7" HDMI display backpack and a 3D printed enclosure. This display monitor is very helpful as a second display for a computer, camera and of course a Raspberry pi. The Adafruit HDMI 7" display backpack features an integrated mini display driver that is great for DIY projects. It's fully assembled, works with any HDMI device and includes mounting tabs for easily attaching to a surface. Connect to a Raspberry pi Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 3 of 18
4 Use as a second monitor Camera preview monitor Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 4 of 18
5 Prerequisite Guides 7" HDMI Monitor Backpack (http://adafru.it/j7f) Parts We have all the lovely components and tools to build this project. Be sure to check out the featured products on the right sidebar. HDMI 7" Display Backpack (http://adafru.it/2406) 2X SPDT Slide Switch (http://adafru.it/drn) UBEC DC/DC Step-Down (http://adafru.it/efd) JST Extension (http://adafru.it/dos) Camcorder Battery Holder (http://adafru.it/efe) 1/4" to 3/8" Convert Screw Adapter for Tripod (http://adafru.it/eff) 1/4" Mount Adapter To Video Camcorder Hot Shoe (http://adafru.it/efg) Phillip Flat Head #4-40 x 3/8 (http://adafru.it/eil) 3/8" to 1/4" Adapter Screw (http://adafru.it/2392) Swivel-Head Pan Tilt (http://adafru.it/2464) Tools & Supplies You'll need a couple of hand tools and accessories to assist you in the build. Solder Iron (http://adafru.it/1204) + Solder (http://adafru.it/734) Silicone Wire (http://adafru.it/1877) PLA Filament (http://adafru.it/dtp) 3D Printer (http://adafru.it/duf) Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 5 of 18
6 Circuit Diagram The Circuit Diagram The slide switch connects to the EN and GND pins on the PowerBoost1000C. The Battery plugs into the JST connection on the PowerBoost + and - pins connect to GND and +5V on the monitor. You can charge the battery by connecting a cable to the USB port on the PowerBoost. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 6 of 18
7 3D Printing The parts are optimized to print with no support material. The two enclosure parts are held together with machine screws. They're oriented in center and should be good to print as is. Download STLs 7inCase.stl 7inLid.stl 220c Extruder 10% Infill 2 Shells 90/120 speeds about 4.5 hours Customize Design You can modify the original solids in the CAD files to make a custom project. Materials The parts can be printed in different types of filament. The most common filaments like PLA and ABS will do just fine but you can of course experiement with copperfill, bamboofill, Semiflex, PET Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 7 of 18
8 and Nylon. Tolerances The parts were tested with common printing settings (listed in the table). With a parameter of 2 shells, theres only a few areas where tolerances really matters - the port cutouts and the mounting holes. Test fit the parts by inserting the top enclosure part over the Raspberry Pi. Check to see if the cutouts fit over the USB and ethernet ports. If the cutout is too tight, you can loosen it with a filing tool. The standoffs with counter bores should fit the machine screws listed in the BOM. These can be threaded by fastening in the appropriate sized screw. Bed Leveling Any parts with large surface require a well leveled build plate. If you're using a heated bed, you can minimize warping. Blue tapers tape, build tak, and sticky adhesives can help keep your part flat and adhere to the bed. Clean up If there's any string or artifacts left over from retraction and oozing, clean up the part by trimming them off using a pair of flush snips. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 8 of 18
9 Assembly Wire length Measue each wire so that you have enough slack to reach the PowerBoost while the lid is open. Take note of the position of the lid, PowerBoost and slide switch. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 9 of 18
10 Bend slide switch leads To make room for the slide switch, we'll need to bend the leads upward so they can fit inside the enclosure. Use flat pliers to bend all three leads upwards and cut off the excess. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 10 of 18
11 Tin and solder switch Add solder to both the wires and leads on the slide switch. Heat shrink Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 11 of 18
12 Cover the soldered leads with heat shrink tubes and apply heat with something like a Hot Air Station (http://adafru.it/1869). Mount slide switch Thread the slide switch wires through the middle port opening. You may need to widen the port depending on your printer tolerence. It should snap into place with a bit of force. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 12 of 18
13 Tin and solder monitor pads Apply a small amount of solder to the GND and +5V pads on the backpack. Solder PowerBoost Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 13 of 18
14 Tin and solder the +5V from the monitor to the + on the PowerBoost. Connect GND on the monitor to the - pin on the PowerBoost. Connect Slide Switch Solder EN and GND on the PowerBoost to each lead on the slide switch. Mount PowerBoost Use #4-40 screws to attach the PowerBoost to the Lid part of the enclosure. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 14 of 18
15 Mount monitor Use four more #4-40 screws to secure to monitor to the inside of the enclosure. Attach Battery Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 15 of 18
16 Use a piece of gaffers tape to secure the battery to the Lid. Use another set of #4-40 screw to attach the Lid to the enclosure. 1/4-20 Tripod screw To attach the monitor to a tripod, we can use a thread adapter with female 1/4" thread to male 3/8" thread. There are two slots on the enclosure to add the thread adapters to allow portrait and landscape setups. Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 16 of 18
17 Camera battery powered To power the monitor through regular camera batteries like a canon, nikon or panisonic; check out the guide for adding a UBEC DC/DC Step-Down Converter: Adafruit Industries https://learn.adafruit.com/7-hdmi-portable-monitor Page 17 of 18
18 https://learn.adafruit.com/diy-camera-monitor/circuit-diagram (http://adafru.it/j8a) Adafruit Industries Last Updated: :10:10 PM EDT Page 18 of 18
DIY Pocket LED Gamer - Tiny Tetris!
DIY Pocket LED Gamer - Tiny Tetris! Created by Jianan Li Last updated on 2014-12-11 11:00:38 AM EST Guide Contents Guide Contents Overview Menu Brightness Adjust Tetris Snake Paint Parts & Tools Parts
DIY Wearable Pi with Near-Eye Video Glasses
DIY Wearable Pi with Near-Eye Video Glasses Created by Ruiz Brothers Last updated on 2015-02-20 09:31:15 AM EST Guide Contents Guide Contents Overview 3D Printing Disassembly Assembly Video Configurations
UV Manicure Lamp. Created by Becky Stern. Last updated on 2014-10-08 04:15:09 PM EDT
UV Manicure Lamp Created by Becky Stern Last updated on 2014-10-08 04:15:09 PM EDT Guide Contents Guide Contents Overview 3D Print Enclosure Build UV Circuit Final Assembly Use it! 2 3 7 10 20 26 Adafruit
3D Print Link's Hylian Shield
3D Print Link's Hylian Shield Created by Ruiz Brothers Last updated on 2015-07-14 04:20:12 PM EDT Guide Contents Guide Contents Overview Parts, Tool & Supplies 3D Printing 3D Printed Parts Slicer Settings
DIY Bluetooth Gamepad
DIY Bluetooth Gamepad Created by Ruiz Brothers Last updated on 2015-03-11 03:15:13 PM EDT Guide Contents Guide Contents Overview Prerequisite Guides Expectations Parts Tools & Supplies Circuit Diagram
Raspberry Pi Pipboy 3000
Raspberry Pi Pipboy 3000 Created by Ruiz Brothers Last updated on 2016-02-05 04:43:25 PM EST Guide Contents Guide Contents Overview Functional Cosplay Props Electronic Parts & Components Tools & Supplies
Adafruit Pi Box Plus. Created by Phillip Burgess. Last updated on 2014-07-24 08:45:08 PM EDT
Adafruit Pi Box Plus Created by Phillip Burgess Last updated on 2014-07-24 08:45:08 PM EDT Guide Contents Guide Contents Assembly Instructions Preparation Parts List Assembly Opening the Lid If Using a
3D Printed Camera Tripod Adapter for Telescope
3D Printed Camera Tripod Adapter for Telescope Created by Ruiz Brothers Last updated on 2015-09-29 06:18:55 PM EDT Guide Contents Guide Contents Overview Designed for Mobile Phones 3D Printing Support
DIY Custom American Girl Doll Prosthetics
DIY Custom American Girl Doll Prosthetics Created by Ruiz Brothers Last updated on 2016-07-25 08:45:21 PM UTC Guide Contents Guide Contents Overview Parts Tools and Supplies 3D Printing 3D Printed Parts
3D Printed Personal Monitor Game Controller Mount
3D Printed Personal Monitor Game Controller Mount Created by Ruiz Brothers Last updated on 2015-03-03 09:15:26 PM EST Guide Contents Guide Contents Overview Parts Tools Customize 3D Printing Printing Techniques
Adafruit Powerboost 1000C
Adafruit Powerboost 1000C Created by lady ada Last updated on 2016-11-26 11:50:53 AM UTC Guide Contents Guide Contents Overview Pinouts Power Pins Control Pins LEDs Battery and USB connection Assembly
Mini RobotShop Rover Development Platform
Mini RobotShop Rover Development Platform Mechanical Assembly Guide Revision 1.1 (Oct 2014) This manual is offered in English only. www.robotshop.com Introduction Thank you for purchasing the Mini RobotShop
LED Wiring and Connections
LED Wiring and Connections A Handbook of How-to Manuals 2009 usledsupply. All Rights Reserved. Index These step by step how to manuals will give you the foundation necessary to use your new LED lights.
Cell Phone Charging Purse
Cell Phone Charging Purse Created by Becky Stern Last updated on 2015-02-20 01:00:16 PM EST Guide Contents Guide Contents Overview Prepare USB and Power Supply Create a Charging Shelf Install Coil in Bag
Happy Chewbacca Mask. Created by John Park. Last updated on :15:49 AM UTC
Happy Chewbacca Mask Created by John Park Last updated on 2016-07-29 02:15:49 AM UTC Guide Contents Guide Contents Overview Mask Teardown Circuit Diagram Build the Circuit Prepare Audio Files Rebuild the
DIY Y6. Build Manual V.A 2014
DIY Y6 Build Manual V.A 2014 1 Contents Thanks for purchasing a DIY Y6! These instructions will show you how to assemble a Y6 using the Pixhawk autopilot system and ArduCopter/APM:Copter firmware. If you
Power Gate Assembly Instructions
Power Gate Assembly Instructions SAFETY NOTICE Thank you for purchasing a Power Gate kit. This kit is intended to be assembled and used by licensed Amateur Radio Operators who are skilled and knowledgeable
3D Printing with Bamboo Wood Filament
3D Printing with Bamboo Wood Filament Created by Ruiz Brothers Last updated on 2015-07-28 01:20:09 PM EDT Guide Contents Guide Contents Overview Usage Temperature Guidelines: Compatible Extruders Temperature
Creator Start-up Guide
www.ff3dp.com Creator Start-up Guide Zhejiang Flashforge 3D Technology Co., Ltd. www.ff3dp.com Contents Precautions:... 1 1. What's in the box?...1 2. Unboxing... 2 3. Initial Hardware Installation...5
Ribcage v1.1 Installation
Ribcage v1.1 Installation Part 2 - Assembly Back-Bone V1.1 Contents Section 1 Before You Get Started... 2 Included With Your Kit:... 2 Figure: A... 3 CAUTION!... 4 Tools Required... 5 Section 2: Ribcage
DIY QUAD. Build Manual V.A 2014
DIY QUAD Build Manual V.A 2014 1 Contents Thanks for purchasing a DIY Quad! These instructions will show you how to assemble a Quad using the Pixhawk autopilot system and ArduCopter/APM:Copter firmware.
FUN LIGHT SWITCH BOX JAMECO PART NO Experience Level: Intermediate Time Required: 4 Hours
FUN LIGHT SWITCH BOX JAMECO PART NO. 2168309 Experience Level: Intermediate Time Required: 4 Hours Kids and adults will find this toy incredibly engaging and fun. Press a button and something lights up.
Assembly notes for the WASP2 microwave processing modules
Assembly notes for the WASP2 microwave processing modules Downconverter module AH 15.1.03 Figure 1: Overview of downconverter module with cover and absorber. When the top is on the absorber is above the
Prusa I3 Build manual
Prusa I3 Build manual Document version: 1.0 TABLE OF CONTENTS Table of contents... 2 About Prusa I3... 3 Change history... 3 Kit description... 4 Safety warnings... 4 Required tools... 4 Assembling the
Document number RS-PRD-00130 Revision 05 Date 20/10/2009 Page 1/30
Date 20/10/2009 Page 1/30 1. Purpose This document describes the field replacement of the footscan plate cable for these models: 2m hi-end plate SN 11/5/xxx 2m pro plate SN 7/5/xxx 0.5m 2003 hi-end plate
MakerBot Tutorial and Test
CARNEGIE MELLON UNIVERSITY MakerBot Tutorial and Test A step by step guide Table of Contents Step 1 Generating a Model...i Step 2 Saving as an STL...1 Step 3 Importing Model to MakerWare...3 Step 4 Positioning
Printrbot Getting Started Guide. For models: Printrbot Plus (v2) Printrbot LC (v2) Printrbot jr
Printrbot Getting Started Guide For models: Printrbot Plus (v2) Printrbot LC (v2) Printrbot jr Contents 4 Chapter 1: Welcome 4 Overview 4 Support 5 Chapter 2: Your Printrbot has arrived... now what? 5
Assembly and User Guide
1 Amp Adjustable Electronic Load 30V Max, 1 Amp, 20 Watts Powered by: 9V Battery Assembly and User Guide Pico Load is a convenient constant current load for testing batteries and power supplies. The digital
WINDOWS 7/8 instruction guide for your Printrbot printer and computer software
Software To start printing with your Printrbot Simple 3d printer, you need to download 3 pieces of software and two digital models (STL files). 1. The teensy Serial Driver. This connects the printer to
TOYOTA TUNDRA 2015 Billet Grille w/led DRL
TOYOTA TUNDRA 2015 Billet Grille w/led DRL Part Number: 00016-34088 Accessory Code: BG3000 Conflicts Models 1794 and Platinum Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3
3D Printer Aluminum Heated Build Plate Kit
3D Printer Aluminum Heated Build Plate Kit Assembly Instructions Product description Aluminum Build Plate was designed to be used as heated build surface of typical 3d printer with 200 x 200 mm XY build
Magnetic shoelaces. Created by Ruiz Brothers. Last updated on :56:59 PM UTC
Magnetic shoelaces Created by Ruiz Brothers Last updated on 2016-12-14 07:56:59 PM UTC Guide Contents Guide Contents Overview Parts, Tools and Supplies 3D Printing Download and 3D Print Slice Settings
Astrosystems Powered Ground Board Hardware Installation 1 * No modification to existing Pivot is necessary
Astrosystems Powered Ground Board Hardware Installation 1 * No modification to existing Pivot is necessary Using the Astrosystems power ground board hardware, a connection from an external 12V dc battery
Steady Hand Game. Build Instructions. Issue 1.2
Game Build Instructions Issue 1.2 Build Instructions The complete set of steady hand parts are shown in the picture on the left. Before you put any components in the board or pick up the soldering iron,
Interior Purse Light. Created by Becky Stern. Last updated on :54:09 PM EDT
Interior Purse Light Created by Becky Stern Last updated on 2016-04-25 05:54:09 PM EDT Guide Contents Guide Contents Overview Circuit Diagram Stitch Sequins Add Tape & Code Use It! 2 3 6 7 11 15 Adafruit
RS232/DB9 An RS232 to TTL Level Converter
RS232/DB9 An RS232 to TTL Level Converter The RS232/DB9 is designed to convert TTL level signals into RS232 level signals. This cable allows you to connect a TTL level device, such as the serial port on
Bill Conkling July 2012
Bill Conkling July 2012 Introduction: For any ham, there are moments that are priceless, like snagging that elusive rare DX station on a deserted island that hasn t been activated in 52 years. And certainly,
Gripper Kit for the Boe-Bot Robot (#28202)
599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 General: info@parallax.com Technical: support@parallax.com Web Site: www.parallax.com Educational: www.stampsinclass.com
ED Tracker Maplin project box build.
ED Tracker Maplin project box build. I've put together this guide to help anyone wanting to case an ED Tracker in a maplin project box. I've built a few ED Tracker's into boxes like this for friends etc.
How to build a Digital Trail Camera using the PixController DigitalEye Trail Camera Kit
Copyright, PixController, Inc. http://www.pixcontroller.com, all rights reserved. How to build a Digital Trail Camera using the PixController DigitalEye Trail Camera Kit Getting Started This tutorial will
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. AUXILIARY WIRE HARNESS P/N 0SA30-HL3-100 SXS700M4/M2 MII 14607 Issue Date Revised October 2013 Honda Dealer: Please give a copy of these
Triac Printed Circuit Board Replacement
Technical Service Bulletin: Triac Printed Circuit Board Replacement TRONIC 5000C Pro Models: WH17, WH27, WH36 Introduction Fig. 1 ELECTRICITY IS EXTREMELY DANGEROUS. TAKE EXTRA PRECAUTIONS AND ENSURE ALL
8TNR56XXD Series Fan. Owner s Guide and Installation Manual. ETL Model NO. : 8TNR56XXD
Owner s Guide and Installation Manual 8TNR56XXD Series Fan ETL Model NO. : 8TNR56XXD Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: MODEL NUMBER: RETAILER NAME:
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual
JDS Labs. cmoybb v2.02 Assembly Guide. Required Tools
JDS Labs 1 of 5 JDS Labs cmoybb v2.02 Assembly Guide Required Tools Soldering iron with a small tip Thin diameter solder (0.032" or smaller highly recommended) Diagonal cutters Small flathead screwdriver
Soldering the PufferFish Circuit Board Rev 5
Soldering the PufferFish Circuit Board Rev 5 1 Educational Resources by The MATE Center is licensed under a Creative Commons AttributionNonCommercial-ShareAlike 4.0 International License. Based on a work
Bill of Materials: Solar Power Supply 5V/3.3V PART NO
Solar Power Supply 5V/3.3V PART NO. 2216948 This project is based on a 6V Solar Cell and constructed with two voltage regulators, one of 5V and other of 3.3V. The projec t is integrated inside a plastic
Provided: 1.3, 1.5 and 2 mm hex wrenches. Not Provided: Small flat head screw driver, pliers.
/ Note: these instructions are intended for users upgrading an existing bot to the MK7. See the complete build instructions if you are building a new Thing-O-Matic. The MakerBot Stepstruder MK7 is our
Altoids Tin Headphone Amplifier Lab
Altoids Tin Headphone Amplifier Lab Michigan State University AEE/IEEE Step 1: Required Parts Table 1 shows a complete listing of the parts required to complete this project. Figure 1 shows a picture of
Programmable Robot Kit
Programmable Robot Kit Code: BCE 003A CONTENTS Connecting block 2 motorised gearboxes INTRODUCTION The Programmable Robot has a control system (called the IQ4 controller) which is easily programmed to
Adafruit Proto Shield for Arduino
Adafruit Proto Shield for Arduino Created by lady ada Last updated on 2016-08-04 11:06:30 PM UTC Guide Contents Guide Contents Overview Make it! Lets go! Preparation Prep Tools Parts list Parts List Optional
HP 16/18-Port Cable Management Kit Installation Guide
HP 16/18-Port Cable Management Kit Installation Guide Abstract This document describes how to attach the HP 16 Port or 18 Port Cable Management Kit to an HP rack. The cable management bracket is designed
Prusa i3 Acrylic Box Frame Mechanical Build Document
Prusa i3 Acrylic Box Frame Mechanical Build Document By 3D Printer Czar For more information, visit www.3dprinterczar.com Complete Prusa i3 Acrylic kit for just $499 http://3dprinterczar.com/shop/3dprinters/prusa-i3/
Instructions for assembling the WARS Powerpole Distribution Kit. (V2)
Instructions for assembling the WARS Powerpole Distribution Kit. (V2) Warning: The construction of this project should only be undertaken by persons with the requisite skills and knowledge and should only
MintySynth Rev. 1.3 Assembly Manual
MintySynth Rev. 1.3 Assembly Manual Tools and materials required: Soldering iron 1/32 solder (leaded solder is easiest to use for beginners) End cutters or diagonal cutters Small needle-nose pliers Paper-hole
Elecraft K3 Audio Output Chip Protection Modification Installation Instructions
Introduction Elecraft K3 Audio Output Chip Protection Modification Installation Instructions Revision B, June 6, 2013 Copyright 2013, Elecraft, Inc. All Rights Reserved Even though the K3 s audio output
Connecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
Hue Learn to Solder Kit
Hue Learn to Solder Kit Parts A. Hue PCB B. RGB LED (Common Cathode) C. Resistors (x3) D. Potentiometers (x3) E. On/Off Switch F. 3V Coin Cell Battery G. Battery Holder Tools A. Soldering Iron B. Solder
HP 36-Port InfiniBand Switch Cable Management Kit Installation Guide
HP 36-Port InfiniBand Switch Cable Management Kit Installation Guide HP Part Number: 574412-doc Published: May 2009 Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein
GENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Auto-Dimming Mirror Kit with Compass and HomeLink 2. APPLICATION: Titan 3. PART NUMBER: 999L1 WS000 4. KIT CONTENTS: Item Qty Description Service
INSTALLATION MANUAL. Installation Instructions
INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate
Cover Page. Factory Radio Other Documents Available For This Vehicle:
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,,2000. Factory Radio
POCKET SIZED GUITAR AMPLIFIER JAMECO PART NO
POCKET SIZED GUITAR AMPLIFIER JAMECO PART NO. 2170521 One of the biggest pains of an electric guitar is the need to hook it up to an amp to hear actual electric guitar sound. That s not a problem with
GT3B Hack Kit Install Instructions Written By Austin Hutchison
GT3B Hack Kit Install Instructions Written By Austin Hutchison Step 1: Remove 4 screws located on top of the radio. 1 Step 2: There are small plastic latches that also hold the top in place. The easiest
DIY Speaker Kit - Manual
DIY Speaker Kit - Manual Technology Will Save Us WELCOME TO THE DIY SPEAKER MANUAL This DIY kit comes with a custom designed amplifier called the Uber Amp 9000 and all of the components you need to make
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-98 - General Layout 866.65.00 Perspective View 0 Plan View 0 05 Order #XXXXX - General Information 866.65.00 Using Your Setup Instructions The Visionary Designs Setup Instructions are
Elecraft K3 KPA3 Power Connector Replacement Revision A Review, April 16, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved
Introduction Elecraft K3 KPA3 Power Connector Replacement Revision A Review, April 16, 2012 Copyright 2012, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module
BUILDING INSTRUCTIONS
etap2hw 38 mm I2C to LCD Interface BUILDING INSTRUCTIONS October 2013 P. Verbruggen Rev 1.01 15-Oct-13 Page 1 Table of Contents Chapter 1 General Information 1.1 ESD Precautions 1.2 Further Supplies 1.3
Web Site: Forums: forums.parallax.com Sales: Technical:
Web Site: www.parallax.com Forums: forums.parallax.com Sales: sales@parallax.com Technical: support@parallax.com Office: (916) 624-8333 Fax: (916) 624-8003 Sales: (888) 512-1024 Tech Support: (888) 997-8267
ASSEMBLY MANUAL MATERIA 101. Revision 04
ASSEMBLY MANUAL MATERIA 101 Revision 04 24 NOVEMBER 2014 00 INDEX 03 01 - Introduction 42 08 - Board wiring 05 06 07 07 07 08 02 - KIT Contents Parts list Box A Box B Box C Notes 46 49 09 - Calibration
Field Install Guide for DVI IO Hardware
Field Install Guide for DVI IO Hardware November 16, 2008 This installation should take between 45-90 minutes depending on your familiarity inside a computer. Table of Contents Section 1 Introduction...
DIY 3D Printing Filament
DIY 3D Printing Filament Created by Ruiz Brothers Last updated on 2014-12-11 11:01:00 AM EST Guide Contents Guide Contents Overview Tools & Supplies Print Cost $40 x 110 / 1000 = $4.40 Preparations Collect,
CNC Shark TM Instruction Manual. Version 1.4 Created 7/27/2010 Updated 8/13/2010
CNC Shark TM Instruction Manual Version 1.4 Created 7/27/2010 Updated 8/13/2010 Table of Contents: CNCShark Assembly Instructions...1 Assembly of the CNC Shark...1 To power the CNC Shark:...2 Downloading
User Manual. English V1-1 -
da Vinci Mini Series User Manual English Specification Product Overview Button and Indicator light Unpacking Accessory Checklist Important Safety Notes Extruder module installation Accessory installation
THE TRILL TREMOLO (K-960)
THE TRILL TREMOLO (K-960) DEPTH SPEED The Trill Tremolo Modkitsdiy.com Unplug when not in use to save battery life. TO AMP IN FROM GUITAR OUT Use these instructions to learn: How to build an effects pedal
BOMB BOOST. CLASSIC PEDAL KIT Assembly Instructions
heet #i-2151 Updated 8/16 BOMB BOO CLAIC PEDAL KI Assembly Instructions he BOMB BOO is a classic pedal created by JH, makers of high-end effects pedals. Whenever JH adds a new pedal to their line, they
INSTALLATION INSTRUCTIONS
Rear Vision System Aftermarket and Factory 5.0, 8.4 and 6.1 MyGig Touch Screen Display (Factory Display requires Chrysler/Dodge dealer to activate) 2009 Current* Dodge Ram (Kit part number 1009-6503) *NOTE:
INSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
NeoPixel Ring Bangle Bracelet
NeoPixel Ring Bangle Bracelet Created by Becky Stern Last updated on 2015-08-29 02:51:42 PM EDT Guide Contents Guide Contents Overview Circuit Diagram Build it! Code Wear it! 2 3 6 7 13 20 https://learn.adafruit.com/neopixel-ring-bangle-bracelet
Setup Step 1.2 Traffic Light assembly
Setup Step 1.2 Traffic Light assembly The following Issues Were Spotted on the Traffic Lights: 1) The LED cables need to be longer It would be better to order longer cables for connection instead of joining
ASSORTMENTS. Imperial Drawer Assortments Your Key to Efficient Maintenance and Repair. Ready To Get Organized? Imperial Drawer Assortments:
Imperial Drawer Assortments Your Key to Efficient Maintenance and Repair. Overall Drawer Size 18" W x 3" H x 12" D Imperial Drawer Assortments: 1. Contain the most popular sizes and styles. 2. Each part
430 Power/Electronics Replacement
Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed
MTH SD70ACe DCC Ready Soundtraxx AT-1000 EMD 710 Sound Decoder Install Revised June 1, 2011
303 447-9251 Fax: 303 447-1406 Sales@UlrichModels.com Introduction MTH SD70ACe DCC Ready Soundtraxx AT-1000 EMD 710 Sound Decoder Install Revised June 1, 2011 The MTH DCC Ready SD70ACe has very little
Alpha Light Installation Instructions
Alpha Light Installation Instructions WARNING: PLEASE READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION, AND CAREFULLY FOLLOW ALL INSTRUCTIONS. IMPROPER INSTALLATION MAY RESULT IN INJURY AND/OR VOID THE
TopSky DLG Installation Manual
TopSky DLG Installation Manual Attention: Because after the compound materials solidify, there will be ammonia iris on the surface, which affect the bonding strength afterwards. Please polish with sandpaper
Corbeau Black 3-Point Retractable Seat Belt (SKU# CS-2SB-BRSB) Installation Instructions
Instructions Created by an: Corbeau Black 3-Point Retractable Seat Belt (SKU# CS-2SB-BRSB) Installation Instructions CAUTION: Safety glasses should be worn at all times when working with vehicles and related
MOTM-900 Power Supply Assembly Instructions & Owner s Manual
MOTM-900 Power Supply Assembly Instructions & Owner s Manual Synthesis Technology 6625 Quail Ridge Dr. Fort Worth, TX 76180 (817) 498-3782 www.synthtech.com June 25, 2003 SYNTHESIS TECHNOLOGY MOTM-900
Printrbot Getting Started Guide. For models: Simple
Printrbot Getting Started Guide For models: Simple Contents 4 4 4 5 5 5 6 6 6 6 7 8 Chapter 1: Welcome Overview Support Chapter 2: Your Printrbot has arrived... now what? Printrbot Kits Pre-Assembled Printrbots
Written By: Walter Galan
Installing iphone 4S Display Assembly Written By: Walter Galan TOOLS: Phillips 00 Screwdriver (1) Plastic Opening Tools (1) PARTS: iphone 4S Display Assembly (1) iphone 4 and 4S Screen Protector (1) Small
THE STEP LADDER (K-978)
THE STEP LADDER (K-978) Footswitch True-bypass = 0 db OUTPUT INPUT Ground shunt switching on the input jack keeps the amp quiet when unplugged from the Step Ladder. Attenuator Pot Full clockwise = 0 db
The Z-Bot Power Draw Bar
The premier source of tooling, parts, and accessories for bench top machinists. The Z-Bot Power Draw Bar The Z-bot Power Draw Bar for mini mills is designed to work with the popular Tormach tooling system.
SCATIR Switch Gooseneck Sensor Mounting Kit
Page 1 of 6 SCATIR Switch Gooseneck Sensor Mounting Kit The SCATIR switch gooseneck sensor is equipped with standard microphone mounting, 5/8-27 thread. Many mounting devices such as pedestals, flanges,
Lathe Milling Attachment
Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,
MGA Alternator Conversion
MGA Alternator Conversion Installation Instructions For 1955 to 1962 MGA PART # 130-078 and #130-088 440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com
18 mm threaded spacers (12) Bottom plate 8 mm threaded spacers (4 plus 4 spare) APM plate. Black arm (3) Blue arm (2) Battery strap
DIY KITS QUAD Thank you for purchasing a 3DR Quad DIY Kit! These instructions will guide you through assembling and wiring your new autonomous multicopter. CONTENTS Your 3DR Quad Kit contains: 30 mm steel
Hot-End Replacement Guide. BFB 3000 plus & 3D Touch
Hot-End Replacement Guide BFB 3000 plus & 3D Touch Pre assembly checks: Testing the hot-end before fitting: Check the heating cable: Set the multi-meter to read resistance (2000 ohms) Test the two outside
OWNER S MANUAL. Ceiling Fan Installation Instructions QUALITY CEILING FANS. For 5SLR52 Series Fans. Total fan weight with light
OWNER S MANUAL Ceiling Fan Installation Instructions Total fan weight with light For 5SLR52 Series Fans READ AND SAVE THESE INSTRUCTIONS QUALITY CEILING FANS Installation SAFETY TIPS WARNING: TO REDUCE
All Models. A-B Battery Supply 90 VOLT B+/9 VOLT A+
ZENITH TRANS-OCEANIC All Models A-B Battery Supply 90 VOLT B+/9 VOLT A+ INCLUDES OPTIONAL POWER SUPPLY FOR DIAL LIGHT CIRCUIT INSTRUCTIONS PARTS LIST BATTERY LAYOUTS WIRING DIAGRAMS TEMPLATES FOR Z-985
I Click on a link tab to jump to that page
& nstall Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory
Polaris Slingshot Trailer Hitch Installation Instructions #PSS007
Polaris Slingshot Trailer Hitch Installation Instructions #PSS007 1. Lay out and familiarize yourself with the components and hardware supplied with the hitch. Note the included trailer wiring isolator