ITALO 3. LED luminaire for street lighting. Registered models Design by Massimo Sacconi and Marzia Bandini MADE IN I TALY

Transcription

1 ERO e GRIGIO per marchi piccoli ED luminaire for street lighting ITAO 3 Registered models Design by Massimo Sacconi and Marzia Bandini (ha il filo ingrossato) MADE I I TAY

2 ITAO 3 PERFORMACE OPTIC Compact design in line with the contemporary trend : ITAO is the exclusive series of AEC luminaires able to meet the needs of the most modern Smart Cities. Functionality, versatility, and a wide variety of optics feature ITAO 3, designed for the lighting of high traffi c urban and suburban streets. Quality light, excellent colour rendering, optimum energy effi ciency. ITAO: a preview on the future of lighting.

3 Available versions Ø / AVAIABE COMPOSITIOS: STE-M / STE-S / STW optic: from 7 to 15 modules. SV optic: from 9 to 15 modules. OPTICA UIT CHARACTERISTICS: Modular optical system. ED source colour temperature: 4000K (3000K, 5700K optional). CRI Ø /76 OPTIOS Ø /76 Please download ITAO 3 photometric data at HEAT SIK PROTECTIO SCREE ITAO 3 TECHICA DATA SHEET 3

4 ITAO 3 MECHAICA CHARACTERISTICS EECTRICA CHARACTERISTICS Frame and cover in die cast aluminum alloy UI E Heat sink in die cast aluminum UI E 1706 with lamellar design. Polyurethane seal. Insulation class: I, II. Power supply: V - 50/Hz. ED current: 525/700mA. Power Factor: >0.9 (at full load). Optical unit lifetime 525mA (Ta=25 C): >70.000hr B2080 (included critical failures); > hr 80, TM-21; 700mA (Ta=25 C): >50.000hr B2080 (included critical failures); >70.000hr 80, TM-21. Available dimming options: DA: automatic dimming; DAC: customizable DA profi le; PM: power line adjustment. tempered glass (5mm thickness) featured by high transparency and optimum thermal and mechanical resistance (IK09). Removable optical unit in 99.85% aluminum. Connection for cables featured by a maximum cross section of 4mmq. Optional fuse. Optical unit lifetime 525mA (Ta=50 C): >50.000hr B2080 (included critical failures); >50.000hr 80, TM-21; 700mA (Ta=40 C): >50.000hr B2080 (included critical failures); >50.000hr 80, TM-21. Removable ED module. Removable metal gear plate. Watertight membrane grommet. Integrated cable clamp. Post top or brackets mounting in die cast aluminum alloy UI E 1706 for Ø Ø76mm. Post top tilt: 0, +5, +10, +15, +20. Bracket tilt: 0, -5, -10, -15, -20. Closure hook in extruded aluminum with stainless steel spring. IP66 protection degree.

5 ERO e GRIGIO per marchi piccoli (ha il filo ingrossato) PROTECTIO AGAIST OVERVOTAGE A lighting device installed in a standard electrical system may be subjected to voltage fluctuations and external disturbances due to different factors such as discontinuous loads on the line, faults on the lines (upstream or downstream) and atmospheric electrical discharges (in outdoor installations). In those ED installations where the electronic components are predominant, an adequate resistance to surges is synonymous with reliability and proper functionality. Thanks to the research and the experimentation performed in its own laboratories, AEC offers its customers customized solutions according to every specific installation. CASS I: protection up to 10kV. CASS II: protection from 6kV up to 9kV. For more information about the protection against overvoltage, please download the technical report at ITAO 3 TECHICA DATA SHEET 5

6 ITAO 3 - optics ITAO 3 STE-M AVAIABE OPTICS AME DESCRIPTIO DRAWIG PHOTOMETRY OPERATIG EVIROMETS Gamma Angles STE-M SUBURBA STREET OPTIC Asymmetrical optic for street and motorway lighting. Specifi c optic for roadways where the width is equivalent to the pole height. STE-S Coordinate system C-Gamma, polar graph. ITAO STE-M (Polare) 500 cd/klm Gamma Angles STE-S SUBURBA STREET OPTIC Asymmetrical optic for street and motorway lighting. Specifi c optic for roadways where the width corresponds to 0, times the pole height. STW Coordinate system C-Gamma, polar graph. ITAO STE-S (Polare) 0 cd/klm Gamma Angles STW WIDE EMISSIO STREET OPTIC Asymmetrical optic for wide streets and wet asphalt. Specifi c optic for roadways where the width corresponds to 1,25 times the pole height. SV Coordinate system C-Gamma, polar graph. ITAO STW (Polare) 0 cd/klm Gamma Angles SV STREET JUCTIOS OPTIC Asymmetrical optic for motorway junctions and narrow street lighting. Specifi c optic for roadways where the width corresponds to 0,5 times the pole height Coordinate system C-Gamma, polar graph. ITAO SV (Polare) 0 cd/klm

7 ERO e GRIGIO per marchi piccoli (ha il filo ingrossato) Installation rep. /H SEECTIO OF THE OPTICS ACCORDIG TO UI E IGHTIG CATEGORIES ITAO 3 ITAO 3 H 1.25 STW STW H 1 STE-M H 0. STE-S STE-M H 0.5 SV UI E ighting categories CEO ME1 CE1 ME2 CE2 ME3 CE3 ME4 CE4 ME5 CE5 ME6 CE6 S1 S2 S3 S4 S5 S6 MEW 1 MEW 2 MEW 3 MEW 4 MEW 5 Street Application Cycle path Application Street Application WET Class ITAO 3 TECHICA DATA SHEET 7

8 Dimming options ED technology offers easy and reliable light fl ux adjustment. The devices are equipped with an electronic power supply capable of adjusting light emission by directly regulating the optical assembly ED input current. The standard version of the device is supplied with a constant ED input current of 525mA or 700mA. The following options are available: DA (DIM-AUTO) OPTIO Automatic light flux regulation The power supply is confi gured using an automatic dimming profi le which fully utilises the maximum light intensity during the fi rst and last few hours of system operation, thereby reducing energy consumption in the middle of the night when a lower level of illumination is often suffi cient. The reduction profi le automatically adapts to the duration of the night-time period during the year. DAC OPTIO (DIM-AUTO CUSTOM PROFIE) The power supply is confi gured using a dimming profi le totally customizable by the user (up to 5 levels in 4 steps). 100% 80% % 40% 20% 0% 100% 100% 70% *Saving in relation to the fi xed power version. 1:100% 2: 70% Tdim: 6hr Saving*: 15% PM OPTIO ight flux regulation using power line communication ight fl ux reduction can be associated with punctual and remote monitoring of the individual device via the power line communication remote control. This option, used in conjunction with an CU (ight Control Unit), makes it possible to control an individual lighting point, allowing the creation of customised lighting scenarios. More complex remote control panels can be used as part of a wireless or GSM/GPRS network, to remotely monitor the energy consumption of the system and provide fault indications as necessary without the need for on-site maintenance procedures. CU CU The ight Control Unit offers fl exible system control. The reduction profi le can be customised with simple local or remote programming. Devices can be divided into sub-groups with different dimming profi les. Option of using an astronomical clock or interfacing with external switching devices. Simplifi ed installation, wiring and testing. Programming software free of charge.

9 ERO e GRIGIO per marchi piccoli (ha il filo ingrossato) OPTIOS O REQUEST (SUBJECT TO FEASIBIITY CHECK) D10 (DIM-10) OPTIO Flux adjustment via 1-10V analogue control Allows lighting device adjustment via an analogue voltage signal between 1V and 10V, the minimum and maximum brightness levels respectively. The device is designed for connection of --1/10V cables. DAI (DIGITA ADDRESSABE IGHTIG ITERFACE) OPTIO Flux adjustment via digital interface DAI is the standard digital technology for the management of luminaires; it is based on a digital signal capable of univocally addressing up to 64 modules on the same bus. The device is designed for connection of --DAI cables. 1-10V DB (DIM-BIP) OPTIO Bi-power light flux adjustment with pilot cable Option mainly designed for underpasses or small systems where a simple and synchronised fl ux reduction PIOT CABE is required. The device is supplied with a bi-power switch which will stablish an operating regime at full or reduced power, depending on whether in additional conductor (pilot cable) is also present or not. 1-10V DAI 1-10V PIOT CABE PIOT CABE D D DR (DIM-REG) OPTIO ight flux adjustment with flux controllers ED retrofi t systems may include a discharge lamp fl ux controller. This option allows the ED device to follow up the voltage adjustment carried out within the system, varying the ED input current as a result. This means both HID and ED devices can be installed within the same system, thereby fully utilising existing energy saving systems. Operation is only guaranteed if amplitude modulation controllers are used instead of phase cut controllers. FUX COTROER ADDITIOA OPTIOS: (Can be combined with all other fl ux reduction options, subject to feasibility check) FC OPTIO - ED light flux recovery The natural depreciation of the light fl ux produced by the EDs can be offset by progressively increasing the input current of the EDs during operation. This option guarantees a virtually constant light fl ux output.the lighting system can therefore be designed while taking account of a maintenance factor which is higher than that usually used with the standard product, offering instant savings in terms of the energy consumed and/or the initial cost of the system. The FC option also means the useful life of the system can be extended. 100% 85% 120% 100% 80% UMIOUS FUX at constant current UMIOUS FUX with FC uminaire wattage at fixed current uminaire wattage with FC 80% 80% FR (FU RAGE) OPTIO - Extended input voltage range Option of supplying the device with an extended input voltage (example: V). This option maintains device operation even in systems where the power supply voltage is adjusted by fl ux controllers VAC 50 / Hz FC (PHOTOCE) OPTIO Possibility to install a twilight switch that allows to automatically turn the unit on at sunset and to turn it off at sunrise. SYSTEM FEATURES AD ADJUSTMET SYSTEM ISTAATIO: DA/DAC PM & CU PM DB DR DAI D10 Independent adjustment system x Central adjustment system (switch / control unit / cabinet) x x x x x x Remote reduction profile change x x x x x x Use of additional cables x x x Remote management software required x Free configuration software (ED and electronic HID systems only) x Interfacing with external regulation systems (e.g. PIR sensors, traffic sensors, switches) x x x x Commissioning by specialist personnel x x x x ITAO 3 TECHICA DATA SHEET 9

10 Product Sheet TECHICA DIVISIO ITAO 3 Rev. AUG-14 DA Profile ITAO 3 MAI CHARACTERISTICS Applications Street lighting STE-M/S: Asymmetrical optic for street lighting (suburban). (0F3) STW: Asymmetrical optic for wide roads and wet asphalts lighting.(0f3) SV: Asymmetrical optic for narrow urban streets or highway entrance/exit turns. (0F2H1) Optic Colour temperature: 4000K, (optional 3000K, 5700K) CRI 70 Photobiological safety class: EXEMPT GROUP CIE Photometrical classification: Semi cut-off IES Photometrical classification: Full cut-off ED source efficiency: mA, Tj=85 C 4000K Insulation class EU: II (I optional) US:1 Protection degree IP66 Impact protection IK09 ED Modules Removable / Replaceable Tilt Angle Post-top: 0, +5, +10, +15, +20 Bracket: 0, -5, -10, -15, -20 Dimensions&weight See the drawing 19Kg Exposed surface Side: 0.1m 2 Top: 0.4m 2 Mounting Bracket or Post-top Ømm Ø76mm Gear tray Removable plate. Operating temp. -40 C / +50 C (525mA) -40 C / +40 C (700mA) Storage temp. -4 C / + 80 C Main reference E 598-1, E , E 62471, E 55015, E 61547, E standards , E PM EECTRICA CHARACTERISTICS Rated voltage V 50/Hz ED current 525mA 700mA Power factor >0,9 (at full load) On-load switch Included, with integrated cable clamp Mains connection For cables max section 4mm 2 F: Fixed output Control system DA: Automatic dimming with default profile. DAC Custom DA profile. PM: Single point communication module. Integrated surge Pulse withstand class I / 1: up to 10kV protection Pulse withstand class II: from 6kV to 9kV 525mA (Ta=25 C) 700mA (Ta=25 C) Optical unit >70.000hr B2080 (including critical fail.) >50.000hr B2080 ( including critical fail.) > hr 80, TM21 >70.000hr 80, TM21 lifetime 525mA (Ta=50 C) 700mA (Ta=40 C) >50.000hr B2080 (including critical fail.) >50.000hr B2080 ( including critical fail.) >50.000hr 80, TM21 >50.000hr 80, TM21 MATERIAS Fixing Die-cast aluminium UI E1706 powder painted. Heat-sink Die-cast aluminium UI E1706 powder painted. ower frame Die-cast aluminium UI E1706 powder painted. Upper canopy Die-cast aluminium UI E1706 powder painted. Closure hook Extruded aluminium with stainless steel spring. Optic 99.85% aluminium with a surface finish in 99.95% with vacuumsealed deposition Screen Flat tempered glass, 5mm thickness. Cable gland Plastic M20x1.5 IP68 Gasket Polyurethane Colour Graphite cod. 01 AEC Illuminazione S.r.l. - aec@aecilluminazione.it STE-M Optic All the published photometrical data has been obtained according to E Optical unit lifetime could be different fot each size of the luminaire. Data listed above are subject to change without notice.

11 Product Sheet TECHICA DIVISIO ITAO 3 Rev. AUG-14 The tables below describe the flux and output power of the available versions. These parameters are necessary in order to guarantee a correct comparison of the luminaire performance. In particular, the luminaire efficiency (expressed in lm/w) must be calculated as the ratio between the output luminous flux of the luminaire and the power absorbed by the input power supply unit. For the sake of completeness the tables also show the data of the nominal flux and power of the used ED. UMIAIRE FUX 1 RATED ED FUX 2 (Ta=25 C, 4000K, lm) (Tj=85 C, 4000K, lm) MODUES 525mA 700mA 525mA 700mA STE-M / STE-S / STW Optic STE-M / STE-S / STW Optic MODUES SV Optic SV Optic RATED UMIAIRE POWER 1 RATED ED POWER 2 ( Ta=25 C, Vin=230Vac, W) F and DA version at full load (Tj=85 C, W) MODUES 525mA 700mA 525mA 700mA STE-M / STE-S / STW Optic STE-M / STE-S / STW Optic MODUES SV Optic SV Optic Multiplier to obtain the flux as a function of Ta and Tk. Ta( C) Multiplier 50 0, , , ,02 5 1,04 0 1,05 Tk(K) Multiplier Multiplier to obtain the power as a function of Ta. Ta ( C) Multiplier 50 0, ,01 egend: Ta =Ambient temperature. Tk = Colour temperature. Example of luminaire data calculation Ta=40 C Tk=4000K 9 ED MODUES, 525mA STE-M Optic Flux: x 0,96 = 18220,8 Power: 1 x 0,99 = 173,3 Efficiency: 18220,8 / 173,3 = lm/w UMIAIRE EFFICIECY ( Ta=25 C, lm/w) MODUES 525mA 700mA STE-M / STE-S / STW Optic MODUES SV Optic ote: The characteristics of the product listed above are subjected to change. They will have to be confirmed in case of order. Values indicated in this technical sheet are to be considered rated values subject to a tolerance of +/-5%. Data listed above are subject to change without notice. 1:Rated data obtained in laboratory 2:Rated data extrapolated from ED manufacturer datasheet. AEC Illuminazione S.r.l. - aec@aecilluminazione.it