SolidWorks Tutorial 4 CANDLESTICK
|
|
|
- Adele Hardy
- 7 years ago
- Views:
Transcription
1 SolidWorks Tutorial 4 CANDLESTICK
2 Candlestick In this tutorial you will make a simple container and a candlestick out of sheetmetal. You will learn about working with sheet metal in SolidWorks. We will show you a couple of ways to create a product out of sheetmetal and we will show you how to make a drawing in 2D. Work plan First we will make a container. Look at the drawing below. We will execute the following steps: 1. First, we will create the base. For this we will use an outside dimension of 230 x After that, we will add four sides with a height of Finally we will look at the 2D drawing of the design. 2
3 1 Start SolidWorks and open a new part. 2 Be sure that the buttons you need to work with SheetMetal are visible. The easiest way to access these tools is to add them to the CommandManager. 3 1 Click on a tab in the CommandManager with the right mouse button. 2 Click on SheetMetal in the menu that appears. Select Top Plane in the FeatureManager. We will use this plane to create a sketch. 4 Create the sketch like in the illustration on the right. Draw a rectangle with one corner above the origin. Set the dimension of the height to 130 and the width to 230. Do you still remember how to start a sketch? If not, look at step 2 and 3 of Tutorial #3. 3
4 5 Next, click on SheetMetal in the CommandManager and then next on Base Flange Set the thickness at 2 mm in the PropertyManager. 2. Click on OK. 7 To create the edges of the container, click on EdgeFlange in the CommandManager. 8 1 Click on the first edge of the base and move the mouse upwards. 2 Set the first rim with a random height. 4
5 9 1-3 Next, click on the other edges. Their heights will automatically adjust to the first one. Change a few settings in the PropertyManager as is shown in the illustration at right: 4. Set the gap between the walls at 1mm. 5. The walls are at a 90 angle to the base The height of the walls is 30mm. 7. This height is measured from the outside of the base. 8. The walls are placed within the outside edge from the base and on top of the base. 9. When the settings are correct, click on OK. The container now. is ready Next we will make a 2D drawing. The last feature in the FeatureManager is FlatPattern1. Normally this feature is suppressed (gray-colored in the FeatureManager), and we have a normal view of the model. By setting this feature to unsuppressed, we will get a 2D drawing of the model. 1. Click on the last feature in the FeatureManager, 2. Select Unsuppress the menu. in 5
6 11 At this point, a 2D drawing of the container is visible. If you want to return to the normal view in 3D, click on the last feature again and select Suppress. 12 Save the model box.sldprt. Work plan as: We are going to create a candlestick. It consists of three parts. First, we will create the base in accordance with the drawing below. We will handle this product differently than we handled the others. We draw a 2D drawing and bring in some bending lines. The hardest part of this model is to make the first sketch. 6
7 13 Open a new part Select the Top Plane, to make a sketch on it. 2. Click on Polygon in the CommandManager. 15 Click on the origin for the first dot of the hexagon and at a point straight above the origin at a random distance from the first one. 16 Be sure that in the PropertyManager: 1. The number of sides is set to The dimension of the inner circle is set. 3. Click on OK. 7
8 17 Set the dimension of the inner circle to 90 mm with Smart Dimension. 18 To set the direction of the hexagon you do as described below: 1. Select ONE of the vertical sides of the hexagon. 2. Click on Vertical in the PropertyManager Click on Offset Entities in the CommandManager. 2 Set the distance in the PropertyManager to 10 mm. 3 Copy the other settings of the PropertyManager from the drawing at the right. Be sure the option Select Chain is NOT selected. 4-6 Select the sides of the hexagon as shown at right. Pay Attention: when the lines are off-set to the inside, check the option Reverse in the PropertyManager. 7. Click on OK. 8
9 20 1. Click on Trim Entities in the CommandManager. 2. Select the option Corner in the PropertyManager. 3-4 Click in the sketch on two lines that form a corner. 21 Click two lines again and again so you see the drawing as shown at right. 22 Finally, we will transform the three inner lines into construction lines. This will create the bending lines we will use later on. 1-3 Select the three lines (use the <Ctrl> button on your keyboard). 4. Check the option For construction in the PropertyManager. 5. Click on OK. 9
10 23 Next, create the base. 1. Click on SheetMetal in the CommandManager. 2. Click on Base-Flange Set the thickness of the material to 0.8 mm in the PropertyManager. 2. Be sure to check or uncheck the option Reverse direction to add the material at the bottom of the base material. Do you have a good view at the material? When not, zoom in! 3. Click on OK. 25 In the sketch we have just created, the bending lines have already been drawn. We are going to use them now, but for this purpose, the sketch must be visible. 1 Click on the + sign in front of Base-Flange1 in the FeatureManager. 2 Now, click on the sketch that is visible (usually this is: Sketch1 ). 3 Click on Show in the menu that appears. The sketch is now graycolored in the model. 10
11 26 Start a new sketch at the top plane: 1. Select the top plane of the item you have just created 2. Click on Sketch in the CommandManager to show the right buttons. 3. Click on the Sketch command to open the sketch. Tip! In earlier exercises, we opened a sketch by selecting a plane and drawing a rectangle (example). SolidWorks understands that in such a case you want to open a sketch and does so automatically. Before you can use the command for the next step, a sketch must be open already; otherwise the command will not be visible. For this reason, we must open the sketch ourselves and that is exactly what we have done in the last step Click somewhere beside the model to unselect the plane. 2-4 Select the three bending lines from the last sketch. Use the <Ctrl> button. 5. Click on Convert Entities in the CommandManager. Tip! For a lot of features in SolidWorks, you must first make a sketch. So you cannot use an edge or an existing line to use them in a new feature. But you CAN do what we have just done here: make a copy of an existing element and paste it in a new sketch. This can be a line from an old sketch but it can also be an edge of a model or even a face. In this way, you can make a new sketch that is derived from the existing model. When an element is not exactly in the plane of the sketch, it will be projected on it. 11
12 Click on SheetMetal in the CommandManager. 2. Click on Bend. Sketched Unfortunately, this function has no preview. You have to set a number of elements without seeing the exact results. 1 Click at a position in the middle of the base to confirm which part of the base is fixed. We will bend the other parts later on. 2 Select the option Material outside: this is related to the way in which the dimensions are in the drawing. 3 With the Reverse direction button you determine in which direction the material is bent (up or down), and the arrow gives you the direction and can be changed by clicking on this button. Make sure the arrow points downwards. 4 Set the corner at Click on OK. 12
13 30 Finally, we will hide the sketch we have revealed earlier. Click on the sketch, and select Hide. 31 The model is ready now. Save is as base.sldprt. 13
14 Work plan The second part of the candlestick is the tube to put the candle in. This is shaped from a piece of sheetmetal as shown in the drawing below. To make this part, we only have to make one sketch. 32 Open a new part and select Top Plane to create a sketch. 33 First, we will draw one half of a circle. 1. Click on Centerpoint Arc in the CommandManager. 2. Click on the origin for the first point. 3. Click directly above the origin to get a second point. 4. To finish this half, click on a third point, directly below the origin. 14
15 34 Next, we will draw the second part of the circle. 1. Click on Tangent Arc in the PropertyManager. 2. Click on the bottom point of the arc you just drew first. 3. Click on a point as shown in the illustration Stop the command by pushing the <Esc> button. Zoom in on the origin of the circle with the center of the second circle also visible. The last one is marked with a little blue + mark. To zoom in, use the scroll wheel of the mouse OR click on Zoom to Area in the View Toolbar. 36 Select both points and click on Vertical in the PropertyManager. 15
16 37 Next, set a dimension of 0.5mm between both points. 38 Next, click on Zoom to fit in the View Toolbar to show the entire sketch. 39 Add two more dimensions tot the sketch with the Smart Dimension command: 1. A radius of 35 for the right arc. 2. A length of 10mm for the overlap between the first circle and the second one. Pay attention: use the real distance between the ends of the circles and NOT the horizontal distance. This is determined when you set the dimension. 16
17 40 Click on SheetMetal in the CommandManager and next on Base Flange. Set the following features in the PropertyManager: 1. Thickness of the material 0.8mm. 2. Height to 25mm. 3. Click on OK. 41 The cylinder is ready now. Save the file er.sldprt. Work plan as hold- Finally we have to make the ear of the candle stick. This is done using the same method we used for the last part. Again, the most important step is making a sketch. 17
18 42 Open a new part and start drawing a sketch at the Front Plane. Draw a line from the origin up. Use the Tangent Arc command to draw a part of a circle (an arc) as is shown in the illustration. 43 Add three dimensions with Smart Dimension as in the illustration on the right. 44 Use the Base Flange command to set the thickness of the material to 0.8mm and a height of 10mm. 18
19 45 Save the file dle.sldprt. as han- 19
20 At the end of this tutorial we will make an assembly. We have done this before. Would you be able to join the three parts together in an assembly? Try it yourself first, before you continue with this tutorial! 46 Open a new assembly. Use the Insert Components command to place the base in the assembly. This will be Fixed. After that, put the two other parts at a random position in the drawing field. Can you remember how this is done? If not, check Tutorial 3 steps 47 to We have to mate the parts together. Click on Mate in the CommandManager. 1. Select the top plane of the base. 2. Select the bottom edge of the holder. 3. The mate type Coincident is selected automatically. 4. Click on OK. Tip! When your first Mate is finished, click on OK. The Mate command will remain active. You can immediately select two other elements to mate. When you click on OK twice, the Mate command will end. SolidWorks assumes that you want to stay within the Mate command. If you click twice on OK by accident, click on the Mate command in the CommandManager to start a new Mate. 20
21 48 Be sure the Matecommand is active (read the tip above). 1. Select the origin of the base in the Feature Tree. 2. Also select the origin of the holder. 3. The mate type Coincident is again selected automatically. 4. Click on OK. 49 Be sure the ear is placed in the area where it has to be at the end. Look at the illustration at right. When this part is placed somewhere else, you can drag it to its correct position. Tip! We are using illustrations of the model in which the model is rotated in such a way that either edges or points that are needed to create a mate remain visible at the same time. This is the most convenient approach, because there will be no need to rotate the model during mating. If this does not work, you will have to rotate the model during the mating command like this: 1. Select the first element. 2. Rotate the model so you can get a good view at the second element. 3. Select the second element. 4. Create the mate. 21
22 During this process, be sure not to close the mate command by accident. So pay attention and focus! 50 Rotate the model so that you can see the bottom of the handle and the bottom of the base. Zoom in so you get a good view of the thickness of the sheetmetal. Make sure the Mate command is still active. Select the two edges as shown in the illustration. The function mate Coincident is selected automatically. Click on OK. 51 Now, try to drag the handle. You will notice that you can shift it along the edges you have just selected and you can also rotate it around this edge. Tip! Notice that there is a difference between rotating a part of the assembly and rotating the model itself. To rotate/shift a part you must drag it. You can also use the buttons Move Component and Rotate Component. You can shift a part in relation to the other parts of the assembly. The model changes. If you rotate the model, the parts remain at the same position in relation to each other, but you will be looking at the model from another angle. The model does NOT change. To do so, you can use the scrollwheel of the mouse (push it and rotate), or you can use the Rotate View command in the View Toolbar. 22
23 52 We are going to join the center points of the edges together. Be sure the Mate command is active. Select both center points. When you move the cursor on top of an edge, the center point will appear and you can select it. The mate type Coincident is selected automatically. Click on OK. 53 Now, try to shift the handle again. Notice that you can only rotate it around the edge but it is fixed in the middle. 54 We will add the last mate to fix the handle completely. Rotate the model so you have a clear view on both planes as in the illustration and select both of them. The mate type Coincident is selected automatically. Click on OK. 55 Click on the OK again to close the Mate command. 23
24 56 The candlestick is ready now. Save it as Candlestick.SLDASM. What are the main fea- In this exercise, you have learned several ways to create parts from sheettures you have learned metal. in this tutorial? You have seen that a Base-Flange is always the first step. In this step you determine the thickness of the material. On a Base-Flange, you can use the edge flange command. With a sketched bend you can create bending lines in the straight plane. You have also seen that you can easily make a 2D drawing out of the 3D model by unsuppressing the last feature. Also you have used some new commands in creating sketches: Centerpoint Arc and Tangent Arc to draw parts of a circle. Convert to use an existing part in a sketch again. Finally, you have made a few tricky mates in the assembly. Slowly you are getting to know SolidWorks better and better, because SheetMetal is an important part of SolidWorks software. 24
SolidWorks Tutorial 3 MAGNETIC BLOCK
SolidWorks Tutorial 3 MAGNETIC BLOCK Magnetic Block In this exercise you will make a magnetic block. To do so, you will create a few parts, which you will assemble. You will learn the following new applications
Understand the Sketcher workbench of CATIA V5.
Chapter 1 Drawing Sketches in Learning Objectives the Sketcher Workbench-I After completing this chapter you will be able to: Understand the Sketcher workbench of CATIA V5. Start a new file in the Part
Chapter 9. Editing Features. Learning Objectives
Chapter 9 Editing Features Learning Objectives After completing this chapter, you will be able to: Edit features. Edit sketches of the sketch based features. Edit the sketch plane of the sketch based features.
Introduction to Autodesk Inventor for F1 in Schools
Introduction to Autodesk Inventor for F1 in Schools F1 in Schools Race Car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s digital prototyping strategy
Introduction to Autodesk Inventor for F1 in Schools
F1 in Schools race car Introduction to Autodesk Inventor for F1 in Schools In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital Prototyping strategy
SolidWorks Tutorial 5
SolidWorks Tutorial 5 Tic-Tac-Toe Preparatory Vocational Training and Advanced Vocational Training Dassault Systèmes SolidWorks Corporation, 75 Wyman Street Waltham, Massachusetts 05 USA Phone: +-800-69-9000
SolidWorks: Mirror, Revolve, and. Introduction to Robotics
SolidWorks: Mirror, Revolve, and Circular Pattern Introduction to Robotics Let s Review At this point we have learned the following: Extrude Boss/Base Extruded Cut Adding Relations and Dimensions Linear
SpaceClaim Introduction Training Session. A SpaceClaim Support Document
SpaceClaim Introduction Training Session A SpaceClaim Support Document In this class we will walk through the basic tools used to create and modify models in SpaceClaim. Introduction We will focus on:
SolidWorks Implementation Guides. Sketching Concepts
SolidWorks Implementation Guides Sketching Concepts Sketching in SolidWorks is the basis for creating features. Features are the basis for creating parts, which can be put together into assemblies. Sketch
Chapter 1. Creating Sketches in. the Sketch Mode-I. Evaluation chapter. Logon to www.cadcim.com for more details. Learning Objectives
Chapter 1 Creating Sketches in Learning Objectives the Sketch Mode-I After completing this chapter you will be able to: Use various tools to create a geometry. Dimension a sketch. Apply constraints to
SolidWorks Building Blocks Tutorial. Toy-car
SolidWorks Building Blocks Tutorial Toy-car From the age of until the age of For use with SolidWorks Educational Release 2010-2011 This tutorial was developed for SolidWorks Worldwide and may be used by
Introduction to CATIA V5
Introduction to CATIA V5 Release 16 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
SolidWorks. SolidWorks Teacher Guide. and Student Courseware
SolidWorks SolidWorks Teacher Guide and Student Courseware SolidWorks Corporation Outside the U.S.: +1-978-371-5011 300 Baker Avenue Fax: +1-978-371-7303 Concord, Massachusetts 01742 USA Email: info@solidworks.com
Sketcher. Preface What's New? Getting Started Basic Tasks Customizing Workbench Description Glossary Index
Sketcher Preface What's New? Getting Started Basic Tasks Customizing Workbench Description Glossary Index Dassault Systèmes 1994-99. All rights reserved. Preface CATIA Version 5 Sketcher application makes
Getting Started in Tinkercad
Getting Started in Tinkercad By Bonnie Roskes, 3DVinci Tinkercad is a fun, easy to use, web-based 3D design application. You don t need any design experience - Tinkercad can be used by anyone. In fact,
2013 Getting Started Guide
2013 Getting Started Guide The contents of this guide and accompanying exercises were originally created by Nemetschek Vectorworks, Inc. Vectorworks Fundamentals Getting Started Guide Created using: Vectorworks
10. THERM DRAWING TIPS
10. THERM DRAWING TIPS 10.1. Drawing Tips The THERM User's Manual describes in detail how to draw cross-sections in THERM. This section of the NFRC Simualation Training Manual presents some additional
Getting Started Guide
3D Architect Home Designer Getting Started Guide Produced and published in the UK by Eleco Software Limited 2014 Eleco plc. All rights reserved. The software and hardware names and labels used in this
SolidWorks tutorial 13-5 Exciting. Includes SolidWorks SustainabilityXpress
SolidWorks tutorial 13-5 Exciting Includes SolidWorks SustainabilityXpress A better world for our children and grandchildren Pre-vocational Secondary Education and Senior Secondary Vocational Education
Generative Drafting. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Generative Drafting Page 1 Tutorial Objectives Description This Tutorial is an introduction to Generative Drafting. Message To show how CATIA V5 allows the user to automatically generate associative drafting
Basic AutoSketch Manual
Basic AutoSketch Manual Instruction for students Skf-Manual.doc of 3 Contents BASIC AUTOSKETCH MANUAL... INSTRUCTION FOR STUDENTS... BASIC AUTOSKETCH INSTRUCTION... 3 SCREEN LAYOUT... 3 MENU BAR... 3 FILE
Introduction to Measurement Tools
Introduction to Measurement Tools Revu's built-in measurement tools make it easy to take length, area, perimeter, diameter, volume and radius measurements, count from PDFs and perform area cutouts. Compatibility
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT
CREATING A 3D VISUALISATION OF YOUR PLANS IN PLANSXPRESS AND CORTONA VRML CLIENT 20-25 Minutes This topic is for users of PlansXpress Total Toolkit Edition. To upgrade to PlansXpress Total Toolkit, call
Edinburgh COLLEGE of ART ARCHITECTURE 3D Modelling in AutoCAD - tutorial exercise The screen The graphics area This is the part of the screen in which the drawing will be created. The command prompt area
Basic 2D Design Be sure you have the latest information!
Basic 2D Design mastercam x getting started tutorials Basic 2D Design December 2011 Be sure you have the latest information! Information might have been changed or added since this document was published.
Tessellating with Regular Polygons
Tessellating with Regular Polygons You ve probably seen a floor tiled with square tiles. Squares make good tiles because they can cover a surface without any gaps or overlapping. This kind of tiling is
ACS Version 10.6 - Check Layout Design
ACS Version 10.6 - Check Layout Design Table Of Contents 1. Check Designer... 1 About the Check Design Feature... 1 Selecting a Check Template... 2 Adding a Check Template... 2 Modify a Check Template...
Creating a Poster in PowerPoint 2010. A. Set Up Your Poster
View the Best Practices in Poster Design located at http://www.emich.edu/training/poster before you begin creating a poster. Then in PowerPoint: (A) set up the poster size and orientation, (B) add and
LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE
LESSON 7: IMPORTING AND VECTORIZING A BITMAP IMAGE In this lesson we ll learn how to import a bitmap logo, transform it into a vector and perform some editing on the vector to clean it up. The concepts
House Design Tutorial
Chapter 2: House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When we are finished, we will have created
Merging Labels, Letters, and Envelopes Word 2013
Merging Labels, Letters, and Envelopes Word 2013 Merging... 1 Types of Merges... 1 The Merging Process... 2 Labels - A Page of the Same... 2 Labels - A Blank Page... 3 Creating Custom Labels... 3 Merged
Sheet Metal Design. Preface What's New? Getting Started Basic Tasks Workbench Description Customizing Glossary Index
Sheet Metal Design Preface What's New? Getting Started Basic Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-99. All rights reserved. Preface The V5 CATIA - Sheet Metal Design
Introduction to SketchUp
Introduction to SketchUp This guide is handy to read if you need some basic knowledge to get started using SketchUp. You will see how to download and install Sketchup, and learn how to use your mouse (and
Mastercam X6 Basic 3D Design
Basic 3D Design mastercam x getting started tutorials Mastercam X6 Basic 3D Design December 2011 Be sure you have the latest information! Information might have been changed or added since this document
Part Design. Page 1 1997 2001 DASSAULT SYSTEMES. IBM Product Lifecycle Management Solutions / Dassault Systemes
Part Design Page 1 Tutorial Objectives Description This tutorial is an introduction to Part Design. Message This tutorial illustrates how CATIA can Design precise 3D mechanical parts with an intuitive
Solidworks Lesson 6 - Assembly & Part Drawings. UCF Engineering
Solidworks Lesson 6 - Assembly & Part Drawings UCF Engineering Mechanical Drawings So far we have been dealing with creating parts and assemblies in SolidWorks, however, when you go to get a part machined,
Kitchen and Bath Design Tutorial
Adding Cabinets Chapter 5: Kitchen and Bath Design Tutorial This tutorial continues where the Materials Tutorial left off. You should save this tutorial using a new name to archive your previous work.
Introduction to Google SketchUp (Mac Version)
Introduction to Google SketchUp (Mac Version) This guide is handy to read if you need some basic knowledge to get started using SketchUp. You will see how to download and install Sketchup, and learn how
What s New V 11. Preferences: Parameters: Layout/ Modifications: Reverse mouse scroll wheel zoom direction
What s New V 11 Preferences: Reverse mouse scroll wheel zoom direction Assign mouse scroll wheel Middle Button as Fine tune Pricing Method (Manufacturing/Design) Display- Display Long Name Parameters:
DOING MORE WITH WORD: MICROSOFT OFFICE 2010
University of North Carolina at Chapel Hill Libraries Carrboro Cybrary Chapel Hill Public Library Durham County Public Library DOING MORE WITH WORD: MICROSOFT OFFICE 2010 GETTING STARTED PAGE 02 Prerequisites
Getting Started with CATIA Version 5
WB Getting Started with CATIA Version 5 Page 1 CATIA User Interface Let s review the following key features: Multi-document support Standard and specific menus & toolbars (File, Edit, Insert, ) Standard
Microsoft Excel 2010 Charts and Graphs
Microsoft Excel 2010 Charts and Graphs Email: training@health.ufl.edu Web Page: http://training.health.ufl.edu Microsoft Excel 2010: Charts and Graphs 2.0 hours Topics include data groupings; creating
SDC. Schroff Development Corporation WWW.SDCACAD.COM PUBLICATIONS. MultiMedia CD by Jack Zecher
MultiMedia CD by Jack Zecher An audioi/visual presentation of the tutorial exercises SDC PUBLICATIONS Schroff Development Corporation WWW.SDCACAD.COM AutoCAD 2002 Tutorial 2-1 Lesson 2 Geometric Construction
Convert 2D to 3D in AutoPOL Bend Simulator
Convert 2D to 3D in AutoPOL Bend Simulator This document gives an introduction of how to convert 2D DXF/DWG files into 3D models in AutoPOL Bend simulator. The AutoPOL 3D concept A 3D model with correct
Creating Drawings in Pro/ENGINEER
6 Creating Drawings in Pro/ENGINEER This chapter shows you how to bring the cell phone models and the assembly you ve created into the Pro/ENGINEER Drawing mode to create a drawing. A mechanical drawing
Visit the following websites to learn more about this book:
INSIDE: MultiMedia CD SolidWorks 2011 Tutorial with MultiMedia CD An audio/visual presentation of the tutorial projects A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Using over 50 feature
Drawing a Bedroom Floorplan
Appendix A Drawing a Bedroom Floorplan In this chapter, you will learn the following to World Class standards: Draw a Bedroom Floorplan Draw the Bedroom Walls Draw and Dimension the Bedroom Door Draw and
Linkage 3.2. User s Guide
Linkage 3.2 User s Guide David Rector Wednesday, April 06, 2016 Table of Contents Table of Contents... 2 Installation... 3 Running the Linkage Program... 3 Simple Mechanism Tutorial... 5 Mouse Operations...
Kitchen and Bath Design Tutorial
Adding Cabinets Kitchen and Bath Design Tutorial This tutorial continues where the Interior Design Tutorial left off. You should save this tutorial using a new name to archive your previous work. The tools
Getting Started With DraftSight A Guide For AEC Users
Getting Started With DraftSight A Guide For AEC Users DraftSight.com Facebook.com/DraftSight Welcome to DraftSight a valuable tool for any AEC professional! DraftSight is more than a free, professional-grade
GYM PLANNER. User Guide. Copyright Powerzone. All Rights Reserved. Software & User Guide produced by Sharp Horizon. www.sharphorizon.com.
GYM PLANNER User Guide Copyright Powerzone. All Rights Reserved. Software & User Guide produced by Sharp Horizon. www.sharphorizon.com. Installing the Software The Powerzone gym Planner is a piece of software
TABLE OF CONTENTS. INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE...
Starting Guide TABLE OF CONTENTS INTRODUCTION... 5 Advance Concrete... 5 Where to find information?... 6 INSTALLATION... 7 STARTING ADVANCE CONCRETE... 7 ADVANCE CONCRETE USER INTERFACE... 7 Other important
Creating Fill-able Forms using Acrobat 8.0: Part 1
Creating Fill-able Forms using Acrobat 8.0: Part 1 The first step in creating a fill-able form in Adobe Acrobat is to generate the form with all its formatting in a program such as Microsoft Word. Then
CATIA Basic Concepts TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Manual Format...2 Log on/off procedures for Windows...3 To log on...3 To logoff...7 Assembly Design Screen...8 Part Design Screen...9 Pull-down Menus...10 Start...10
Chapter 23: Drafting in Worksheet View
Chapter 23: Drafting in Worksheet View Worksheet View is a powerful, 2D production drafting module. Here you can find all of the drawing and editing tools needed to create fast, accurate, detailed working
CONSTRUCTING SINGLE-SUBJECT REVERSAL DESIGN GRAPHS USING MICROSOFT WORD : A COMPREHENSIVE TUTORIAL
CONSTRUCTING SINGLE-SUBJECT REVERSAL DESIGN GRAPHS USING MICROSOFT WORD : A COMPREHENSIVE TUTORIAL PATRICK GREHAN ADELPHI UNIVERSITY DANIEL J. MORAN MIDAMERICAN PSYCHOLOGICAL INSTITUTE This document is
Create a Poster Using Publisher
Contents 1. Introduction 1. Starting Publisher 2. Create a Poster Template 5. Aligning your images and text 7. Apply a background 12. Add text to your poster 14. Add pictures to your poster 17. Add graphs
An introduction to 3D draughting & solid modelling using AutoCAD
An introduction to 3D draughting & solid modelling using AutoCAD Faculty of Technology University of Plymouth Drake Circus Plymouth PL4 8AA These notes are to be used in conjunction with the AutoCAD software
Communicate: In Print
Communicate: In Print A simple guide Work areas Communicate: In Print has two different modes in which to edit your documents: Create and Adjust modes. These are easily interchangeable and the toolbars
Using Microsoft Word. Working With Objects
Using Microsoft Word Many Word documents will require elements that were created in programs other than Word, such as the picture to the right. Nontext elements in a document are referred to as Objects
2. More Use of the Mouse in Windows 7
65 2. More Use of the Mouse in Windows 7 The mouse has become an essential part of the computer. But it is actually a relatively new addition. The mouse did not become a standard part of the PC until Windows
Task Card #2 SMART Board: Notebook
Task Card #2 SMART Board: Notebook Objectives: Participants will learn how to utilize the SMART Notebook. Table of Contents: Launching The SMART Notebook Page 1 Entering Text Page 1 Top Toolbar Page 2
Online Training Program Offered by CADCIM Technologies
Online Training Program Offered by CADCIM Technologies CADCIM Technologies provides effective and affordable online training on various software packages including Computer Aided Design and Manufacturing
Torchmate CAD User s Guide
Torchmate CAD User s Guide Revised May 2011 Table of Contents: Overview of the Manual Installation and Setup Important Configuration Changes Overview of Menus Navigation and Selection Methods Basic CAD
Instructions for creating a data entry form in Microsoft Excel
1 of 5 You have several options when you want to enter data manually in Excel. You can enter data in one cell, in several cells at the same time, or on more than one worksheet (worksheet/spreadsheet: The
CATIA Drafting TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Drafting...2 Drawing Screen...3 Pull-down Menus...4 File...4 Edit...5 View...6 Insert...7 Tools...8 Drafting Workbench...9 Views and Sheets...9 Dimensions and Annotations...10
Structure Design. Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index
Structure Design Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-2000. All rights reserved. Preface CATIA Version
Scientific Graphing in Excel 2010
Scientific Graphing in Excel 2010 When you start Excel, you will see the screen below. Various parts of the display are labelled in red, with arrows, to define the terms used in the remainder of this overview.
TurboCAD Architectural
TurboCAD Architectural Version 15 Getting Started Guide IMSI/Design LLC, US 100 Rowland Blvd. Novato. CA 94945, USA Tel: +1-415-878-4000 Fax: +1-415-897-2544 Web Site www.imsisoft.com www.turbocad.com
Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional.
Workspace tour Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional. In this tutorial, you will become familiar with the terminology and workspace
House Design Tutorial
Chapter 2: House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When you are finished, you will have
Why Use OneNote? Creating a New Notebook
Why Use OneNote? OneNote is the ultimate virtual notebook that enables users to create notes in various formats, shares those notes, sync those notes with the cloud and collaborate with others. You can
Smart Board Notebook Software A guide for new Smart Board users
Smart Board Notebook Software A guide for new Smart Board users This guide will address the following tasks in Notebook: 1. Adding shapes, text, and pictures. 2. Searching the Gallery. 3. Arranging objects
CATIA for Design and Engineering. Version 5 Releases 14 & 15. David S. Kelley. Central Michigan University SDC
CATIA for Design and Engineering ersion 5 Releases 4 & 5 David S. Kelley Central Michigan University SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com TUTORIAL Extruded
ArchiCAD Tutorial Getting started. Dr. Benny Raphael Dept. of Building National University of Singapore (NUS)
ArchiCAD Tutorial Getting started Dr. Benny Raphael Dept. of Building National University of Singapore (NUS) Launch ArchiCAD You can either create a new project or open an existing (previously saved) project.
Publisher 2010 Cheat Sheet
April 20, 2012 Publisher 2010 Cheat Sheet Toolbar customize click on arrow and then check the ones you want a shortcut for File Tab (has new, open save, print, and shows recent documents, and has choices
Layout Tutorial. Getting Started
Getting Started Layout Tutorial This tutorial will explain how create a layout template, send views to a layout page, then save the document in PDF format. In this tutorial you will learn about: Creating
CATIA Functional Tolerancing & Annotation TABLE OF CONTENTS
TABLE OF CONTENTS Introduction...1 Functional Tolerancing and Annotation...2 Pull-down Menus...3 Insert...3 Functional Tolerancing and Annotation Workbench...4 Bottom Toolbar Changes...5 3D Grid Toolbar...5
A Guide to Microsoft Paint (Windows XP)
A Guide to Microsoft Paint (Windows XP) Introduction Microsoft Paint allows you to produce your own pictures (or edit existing ones). In Windows XP, you can no longer access Paint directly from the Microsoft
How to Use the Drawing Toolbar in Microsoft Word
How to Use the Drawing Toolbar in Microsoft Word The drawing toolbar allows you to quickly and easily label pictures (e.g., maps) in a MS Word file. You can add arrows, circle spots, or label with words.
To draw a line. To create a construction line by specifying two points
Drawing Lines, Polygons and Rectangles The line is the basic object in AutoCAD. You can create a variety of lines: single lines, multiple line segments with and without arcs, multiple parallel lines, and
Click on various options: Publications by Wizard Publications by Design Blank Publication
Click on various options: Publications by Wizard Publications by Design Blank Publication Select the Blank Publications Tab: Choose a blank full page Click on Create New Page Insert > Page Select the number
Sheet Metal Design: Beyond Bends and Flanges
11/30/2005-8:00 am - 9:30 am Room:Pelican 1 (Swan) Walt Disney World Swan and Dolphin Resort Orlando, Florida Sheet Metal Design: Beyond Bends and Flanges Anthony B. Rodriguez - KETIV Technologies MA31-2
YouthQuest Quick Key FOB Project
YouthQuest Quick Key FOB Project This project is designed to demonstrate how to use the 3D design application, Moment of inspiration, to create a custom key fob for printing on the Cube3 3D printer. Downloading
Etch Drawing Preparation
Etch Drawing Preparation Introduction Most etching companies prefer you to supply the drawing for your design in the form of a computer file. While some will still accept drawn or printed artwork, it is
Roof Tutorial. Chapter 3:
Chapter 3: Roof Tutorial The majority of Roof Tutorial describes some common roof styles that can be created using settings in the Wall Specification dialog and can be completed independent of the other
Creating Custom Crystal Reports Tutorial
Creating Custom Crystal Reports Tutorial 020812 2012 Blackbaud, Inc. This publication, or any part thereof, may not be reproduced or transmitted in any form or by any means, electronic, or mechanical,
1. Kyle stacks 30 sheets of paper as shown to the right. Each sheet weighs about 5 g. How can you find the weight of the whole stack?
Prisms and Cylinders Answer Key Vocabulary: cylinder, height (of a cylinder or prism), prism, volume Prior Knowledge Questions (Do these BEFORE using the Gizmo.) [Note: The purpose of these questions is
Sample Table. Columns. Column 1 Column 2 Column 3 Row 1 Cell 1 Cell 2 Cell 3 Row 2 Cell 4 Cell 5 Cell 6 Row 3 Cell 7 Cell 8 Cell 9.
Working with Tables in Microsoft Word The purpose of this document is to lead you through the steps of creating, editing and deleting tables and parts of tables. This document follows a tutorial format
SketchUp Instructions
SketchUp Instructions Every architect needs to know how to use SketchUp! SketchUp is free from Google just Google it and download to your computer. You can do just about anything with it, but it is especially
Fireworks CS4 Tutorial Part 1: Intro
Fireworks CS4 Tutorial Part 1: Intro This Adobe Fireworks CS4 Tutorial will help you familiarize yourself with this image editing software and help you create a layout for a website. Fireworks CS4 is the
PDF Web Form. Projects 1
Projects 1 In this project, you ll create a PDF form that can be used to collect user data online. In this exercise, you ll learn how to: Design a layout for a functional form. Add form fields and set
Microsoft Office 2007 The Drawing Tools (Level 2)
IT Services Microsoft Office 2007 The Drawing Tools (Level 2) Contents Introduction...1 Activating the Drawing Tools...2 Editing Drawing Objects...3 Changing the Size/Shape of an Object...3 Changing the
3D-GIS in the Cloud USER MANUAL. August, 2014
3D-GIS in the Cloud USER MANUAL August, 2014 3D GIS in the Cloud User Manual August, 2014 Table of Contents 1. Quick Reference: Navigating and Exploring in the 3D GIS in the Cloud... 2 1.1 Using the Mouse...
Drawing a little mechanical part using LibreCAD
TUTORIAL Drawing a little mechanical part using LibreCAD Tutorial by Claudio Guarnieri CLAUDIO GUARNIERI: Drawing a little mechanical part using LibreCAD Page 1 of 17 Introduction Hello everyone! This
Part Design. Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index
Part Design Preface What's New? Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-99. All rights reserved. Preface The CATIA Version 5 Part
Creating Posters in Excel (2007 & 2010)
Creating Posters in Excel (2007 & 2010) Although it would be nice to have a poster printer in each of our homes and work areas, having such a tool is unfortunately not something that will become a reality
Windows 95. 2a. Place the pointer on Programs. Move the pointer horizontally to the right into the next window.
Word Processing Microsoft Works Windows 95 The intention of this section is to instruct basic word processing skills such as creating, editing, formatting, saving and closing a new document. Microsoft
Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional.
Creating a logo Welcome to CorelDRAW, a comprehensive vector-based drawing and graphic-design program for the graphics professional. In this tutorial, you will create a logo for an imaginary coffee shop.