VIESMANN. VITODENS AND VITOSOLAR Flue systems for gas condensing boilers 1.9 to kw. Technical guide FLUE SYSTEMS VITODENS AND VITOSOLAR

Transcription

1 VIESMANN VITODENS AND VITOSOLAR Flue systems f gs ondensing oilers 1.9 to kw Tehnil guide FLUE SYSTEMS VITODENS AND VITOSOLAR 5/01

2 Index Index 1. Flue systems 1. 1 Flue systems... 4 Struturl unit... 4 System ertifition Blned flue opertion Open flue opertion Flue gs high limit sfety ut-out Lightning protetion E ertifition f PPs flue systems (rigid nd flexile) f the Vitodens Flue instlltion options f lned flue opertion... 8 In the living spe (oupied re) with one me full steys ove... 8 In the living spe (oupied re), immeditely underneth the roof with only ttis ove (rted heting output 50 kw)... 9 In the instlltion room, with ventiltion ir supplied through the externl wll... 9 Severl Vitodens in the living spe in oupied res (living spe - rted heting output 50 kw) Flue instlltion options f open flue opertion In the instlltion room (non-living spe) with one me full flos ove (ompulsy f the Vitodens 00-W from 60 kw) Speil version: Open flue opertion nd instlled in the living spe (oupied re) with interonneted room ir supply (rted heting output 5 kw) Flue gs heder f severl Vitodens 00-W, -W nd -F positive pressure 11 Flue gs heder f severl Vitodens negtive pressure Design nd sizing infmtion f onnetion on the flue gs side. Plsti (PPs) lned flue system f routing through shft lned flue opertion (type 9x to TRGI 008)... 1 Internl shft dimensions to DIN V Flue, system size 60, 80 nd 100 (omponents) (type 9x ding to TRGI 008) 14 Vitodens in onjuntion with solid fuel oilers Flue, flexile, system size 60, 80 nd 100 (omponents) (type 9x ding to TRGI 008) Plsti (PPs) lned flue system f vertil routing through pithed flt roof (type x, to TRGI 008) F vertil roof outlets when the Vitodens is instlled in ttis Vertil flt roof outlet Plsti (PPs) lned flue system f externl wll onnetion (type 1x to TRGI 008)... 0 Mx. totl length of the flue pipe Plsti (PPs) flue/ventiltion ir system f seprte ventiltion ir nd flue gs routing (type 8x to TRGI 008) Plsti (PPs) lned flue system f routing over externl wlls (type 5x, to TRGI 008) Plsti (PPs) lned flue system f routing through lightweight shft... 4 "UNIFIX" shft profiles offered y Skoerne (mde from erted onrete)... 4 "SKOBIFIXnno" nd "SKOBIFIXXs 0" shft profiles offered y Skoerne (mde from fomed ermis)... 4 Anhing f roof outlets with shft profiles... 5 Shft profiles offered y Promt... 5 Roof outlet f shfts with Promt profiles Plsti (PPs) lned flue system f routing multiple pipes through shft... 6 Lyout exmples Plsti (PPs) lned flue system (onnetion pipe) f onneting multiple flues to single room seled lned flue system... 7 Room seled lned flue system, negtive pressure (type 4x, to TRGI 008) 8 Room seled lned flue system, positive pressure multiple onnetion with the Vitodens 00-W, -W nd -F up to 6 kw (type 4x to TRGI 008)... 8 VIESMANN VITODENS AND VITOSOLAR

3 Index (ont.).10 Plsti (PPs) flue pipe f routing through shft open flue opertion (type B, to TRGI 008)... 1 Internl shft dimensions... 1 Flue, system size 60, 80 nd 100 (omponents) (type B /B ding to TRGI 008)... Flue, flexile, system size 60, 80 nd 100 (omponents) (type B to TRGI 008) 4 Speil version: open flue opertion with omustion ir interonnetion f the Vitodens up to 5 kw (type B to TRGI 008)... 5 onnetion to moisture-resistnt himney (MR himney negtive pressure) with plsti (PPs) flue pipe (type B x, ding to TRGI 008)... 6 Multi oiler systems with flue systems under positive pressure (open flue opertion) Vitodens 00-W, Vitodens -W nd -F... 7 Multi oiler systems with flue systems under negtive pressure Flue system omponents. 1 Blned flue system omponents omponents f routing flue over n externl wll Single pipe system omponents omponents f multiple onnetions to room seled lned flue system positive pressure f the Vitodens 00-W, -W nd -F, 19 to 6 kw omponents of the flexile single pipe system f flexile flues omponents f multi oiler systems Flue gs heder Roof elements Keywd index VITODENS AND VITOSOLAR VIESMANN

4 1 Flue systems 1.1 Flue systems The following requirements regrding design nd instlltion pply to flue systems f ondensing omustion equipment: Pri to strting wk on the flue system, your heting ontrt should onfer with the responsile flue gs inspet [where pplile]. Gs omustion equipment must e onneted to the domesti himney on the sme flo where it is instlled (no trnsition through seprting eilings). Here, differentition is required s to whether the ondensing oiler should e instlled in the living spe (oupied rooms) in the nonliving spe (instlltion room). Struturl unit The fementioned onditions re generlly met when E-designted flue systems (essies) re used together with the Vitodens. The following Viessmnn lned flue systems f lned flue opertion re tested to DVGW nd re E-designted s single struturl unit with the Vitodens: Vertil roof outlet Externl wll onnetion Hizontl roof outlet Externl routing through oxil pipe Advntges of single struturl units: No lulted perfmne verifition f flues to EN 184 is required f individul ses Simplified visul inspetion y the lol flue gs inspet every two yers No dditionl pprovl ertifite y the flue pipe mnufturer is required Siting the Vitodens in the living spe is fesile, sujet to the flue inside the living spe eing routed inside protetive pipe nd eing surrounded y ventiltion ir (lned flue system, lned flue opertion). As speil se, n instlltion inside the living spe is lso fesile f open flue opertion, provided onnetion piee with seondry ventiltion up to the shft (opertion with interonneted room ir supply) is provided (see pge 5). Outside the living spe, the flue pipe in the instlltion room my lso e routed without seondry ventiltion. However, the instlltion room would then require n dequtely sized ventiltion ir perture to the outside (. to TRGI 008). Rted heting output up to 50 kw: 150 m 75 m Rted heting output ove 50 kw (e.g. Vitodens 00-W, from 60 kw, multi oiler systems): 150 m plus m f eh kw ove 50 kw The ountry-speifi regultions (whih my inlude the TR Gs nd ÖVGW guidelines) pply to the instlltion of this ppline. The plin flue must e type pproved y the Deutshes Institut für Butehnik (DIBt) [Germny] (open flue opertion). The flue ville s n essy is E-designted nd pproved in dne with EN System ertifition System ertifition to E Gs Applines Diretive 009/14/E in onjuntion with PPs flues offered y Skoerne Vitodens 00-W Vitodens -F Vitodens -W Vitodens 4-F Vitodens 00-W Vitodens -F Vitodens 4-F Vitosolr 00-F E-0085N0050 E-0085N0050 E-0085N0050 E-0085N0050 E-0085M046 E-0085M046 E-0085M046 E-0085M Blned flue opertion Due to the seled omustion hmer the Vitodens gs ondensing oilers re suitle f lned flue opertion. These oilers re tegised s equipment type 1x, x, 4x, 5x, 6x, 8x 9x ding to TRGI 008 ("x" only pplies to DE). With this type of equipment (exept 6x ) there is joint pprovl f the Vitodens nd lned flue system. F this type of onstrution the tightness test (overpressure test) y the flue gs inspet during ommissioning nd the verifition of "Generl Building Regultions pprovl" y the DIBt my e omitted. Any pproved flue system n e used f type 6x. This flue system is not tested together with the oilers. Mintin the dimensions speified on pges 1 to. The omustion ir is supplied nd the flue gs extrted through one onentri oxil pipe (lned flue system). The omustion ir is supplied through the nnulr gp etween the externl luminium ventiltion ir pipe nd the flue pipe. Flue gses re dishrged through the internl plsti pipe (PPs). F lned flue systems tested together with the wll mounted gs oiler there is no requirement f tightness test during ommissioning y the flue gs inspet. In suh ses we reommend tht your heting ontrt rries out simple tightness test during the ommissioning of your system. F this, it is suffiient to hek the O onentrtion in the omustion ir t the nnulr gp of the lned flue pipe. The flue pipe is deemed to e gs-tight if the O onentrtion in the omustion ir is no higher thn 0. % the O onentrtion is t lest 0.6 %. hek the flue system f tightness y pressure testing if higher O lower O vlues re estlished. In onjuntion with the onentri oxil pipe (lned flue system), the surfe temperture of the Vitodens tht of the lned flue system will never exeed 85. Therefe, lernes to omustile omponents ding to TRGI re not required. F oiler types 6x nd 4x, the DIBt-pproved flue pipes from Viessmnn lterntive DIBt-pproved flue pipes y other mnufturers my e used. Use ondenste trp ove the oiler flue onnetion if luminium flue pipes re used. Instll the onneting pipes (routed hizontlly) with fll of t lest to the oiler. In ddition, we reommend using lips sped out 1 m prt to suppt the onnetion pipe. The lned flue system is E-designted nd pproved in dne with EN (see pge 6). 4 VIESMANN VITODENS AND VITOSOLAR

5 Flue systems (ont.) The oiler sing retes system tht is seled ginst its surroundings. Any leks used y esping flue gs re returned vi the omustion ir, therey preventing flue gs from entering the living spe. When instlling the Vitodens in sement on lower flo, n existing himney shft of dequte size my e used f the lned flue opertion (type 4x nd 9x ). Ading to TRGI 008, flues tht ridge severl flos must e routed inside shft with fire rting of t lest 90 minutes, nd f uildings in tegies 1 nd, fire rting of t lest 0 minutes. The flue gs/ventiltion ir is routed to the himney shft in lned flue. The flue pipe is then routed inside the himney shft to ove the roof. Where no suitle shft is ville, the flue my e routed to the roof through retrofitted shft. F this shft, Building Regultions test ertifite E designtion responding to the design of the shft is required. In ddition, the shft must hve fire rting of L0 L Open flue opertion (Type B nd B ) The flue gs is routed through single wll plsti flue pipes (PPs). The flue system is E-designted nd pproved in dne with EN (see pge 6). The omustion ir supply is ensured vi the nnulr gp etween the flue pipe nd the ventiltion ir inlet on the oiler flue onnetion of the Vitodens. Instll the onneting pipes (routed hizontlly) with fll of t lest to the oiler. In ddition, we reommend using lips sped out 1 m prt to suppt the onnetion pipe. 1.4 Flue gs high limit sfety ut-out Ading to E designtion to EN the plsti flue pipe (PPs) n e used f flue gs tempertures of up to 10 (type B). Mesures inside the equipment ensure tht the flue gs temperture will never exeed 90. A flue gs high limit sfety ut-out is therefe not required. 1.5 Lightning protetion If lightning protetion system is instlled, ny metlli flue system should e inluded in the lightning protetion sheme. VITODENS AND VITOSOLAR VIESMANN 5

6 Flue systems (ont.) 1.6 E ertifition f PPs flue systems (rigid nd flexile) f the Vitodens 1 6 VIESMANN VITODENS AND VITOSOLAR

7 Flue systems (ont.) 1 VITODENS AND VITOSOLAR VIESMANN 7

8 Flue systems (ont.) Flue instlltion options f lned flue opertion No seprte vents re required in the instlltion room. In the living spe (oupied re) with one me full steys ove Routing through shft (Type 9x, to TRGI 008) The oiler drws omustion ir from the outside through the nnulr gp in the shft (himney) nd expels the flue gs vi the flue pipe to ove the roof. F ondensing oilers > 50 kw the instlltion room must e ventilted even with lned flue opertion. The shft is not prt of the stndrd delivery. F detiled desription, see from pge 1. Retrofitted shfts Instlltion in retrofitted shft pproved y the uilding inspette [Germny], onsisting of individul shft elements (e.g. s supplied y SIMO, Wienererger Skoerne) inluding minerl profiles (e.g. from Promtet). F detiled desription of shfts, see pge 4. A Flue gs B Ventiltion ir A Flue gs B Ventiltion ir Externl wll onnetion Only f existing flues with exemption rights (Type 1x, to TRGI 008) (Permissile up to rted heting output of 11 kw f entrl heting 8 kw f DHW heting) Ading to the LndesFeuVo, issue 1999 [Germny], n externl wll onnetion is only permissile in individul ses, where routing the flue gs y other mens is not pproprite f tehnil eonomil resons. The oiler drws omustion ir from outside vi onentri oxil pipe fitted to the externl wll nd expels flue gs to the outside vi the externl wll. F detiled desription, see pge 0. Hizontl roof outlet (Type 1x, to TRGI 008) (No limit f rted heting output) The oiler drws omustion ir from outside vi onentri oxil pipe t the dmer nd expels flue gs to the outside t the dmer. Routing over externl wlls (Type 5x, to TRGI 008) The oiler drws omustion ir from the outside vi hizontl, onentri oxil pipe on the externl wll nd expels flue gs to the outside vi the roof. In the vertil setion the externl pipe of the onentri oxil pipe ts s therml insultion, thnks to the stti ir gp. The omustion ir is supplied vi the lned flue ir inlet piee. F detiled desription, see pge. A Flue gs B Ventiltion ir 8 VIESMANN VITODENS AND VITOSOLAR

9 Flue systems (ont.) In the living spe (oupied re), immeditely underneth the roof with only ttis ove (rted heting output 50 kw) Vertil outlet, if no shft is ville (Type x, to TRGI 008) (Vrious design options) 1 Diret, vertil roof outlet through pithed roof Indiret, vertil roof outlet through pithed roof with protetive pipe in the tti (not onverted) fire protetion rikwk (onverted tti) Diret, vertil roof outlet through flt roof The oiler drws omustion ir from the outside nd expels flue gs to the outside through onentri oxil pipe vi the roof. F detiled desription, see pge A Flue gs B Ventiltion ir Protetive pipe to prevent mehnil dmge In the instlltion room, with ventiltion ir supplied through the externl wll A B Seprte ventiltion ir nd flue gs routing (Type 8x, to TRGl 008) The oiler drws omustion ir from outside vi seprte supply pipe routed through the externl wll, nd expels flue gs to the outside vi shft leding through the roof. The onnetion piee to the himney is designed s oxil pipe. This lned flue system is used if the existing himney is unsuitle f routing omustion ir due to its dimensions hrteristis (deposits). F detiled desription, see pge 1. A Flue gs B Ventiltion ir Severl Vitodens in the living spe in oupied res (living spe - rted heting output 50 kw) Instlltion on different flos (Type 4x, to TRGI 008) Opertion with negtive pressure: Room seled lned flue system required. Opertion with positive pressure: Blned flue system f multiple onnetions. Severl het soures drw omustion ir from the outside through the nnulr gp of the room seled lned flue system nd expel flue gs to the outside vi the roof, through moisture-resistnt internl pipe. F detiled desription, see pges 7 nd 8. A Flue gs B Ventiltion ir VITODENS AND VITOSOLAR VIESMANN 9

10 Flue systems (ont.) 1.8 Flue instlltion options f open flue opertion 1 (Seprte ventiltion ir perture, 150 m 75 m ross-setion required) F instlltion in Austri, oserve the relevnt sfety regultions of the ÖVGW-TR Gs (G1) 1985, ÖVGW-TRF (G), ÖNORM, ÖVGW, ÖVE nd regionl regultions. In the instlltion room (non-living spe) with one me full flos ove (ompulsy f the Vitodens 00-W from 60 kw) Routing through shft (Type B, to TRGI 008) The oiler drws omustion ir from the instlltion room nd expels flue gs through the flue to ove the roof (lned flow). F detiled desription, see pge 1. A Flue gs B Seondry ventiltion Ventiltion ir onnetion to moisture-resistnt himney (MR himney) (Type B, to TRGI 008) The oiler drws omustion ir from the instlltion room nd routes flue gs through the moisture-resistnt himney to ove the roof. F detiled desription, see pge 6. A Flue gs B Seondry ventiltion Ventiltion ir 10 VIESMANN VITODENS AND VITOSOLAR

11 Flue systems (ont.) Speil version: Open flue opertion nd instlled in the living spe (oupied re) with interonneted room ir supply (rted heting output 5 kw) Routing through shft onnetion to moisture-resistnt himney (Type B, to TRGI 008) The oiler drws omustion ir from the living spe vi oxil pipe with ventiltion ir pertures upstrem of the shft inlet nd expels the flue gs either vi flue pipe vi moisture-resistnt himney through the roof (omustion ir supply vi interonneted rooms ding to TRGI). F detiled desription, see pge 5. 1 A Flue gs B Ventiltion ir Seondry ventiltion D Do E Interonneted ir supply Flue gs heder f severl Vitodens 00-W, -W nd -F positive pressure Type B, to TRGI 008 Severl oilers inside the sme room drw omustion ir from outside vi ventiltion pertures nd expel the flue gs through ommon flue pipe to the outside vi the roof. F detiled desription, see pge 7. A Flue gs B Seondry ventiltion Ventiltion ir Flue gs heder f severl Vitodens negtive pressure Type B, to TRGI 008 Severl oilers inside the sme room drw omustion ir from outside vi ventiltion pertures nd expel the flue gs through ommon flue pipe to the outside vi the roof. F detiled desription, see pge 45. A Flue gs B Ventiltion ir VITODENS AND VITOSOLAR VIESMANN 11

12 Design nd sizing infmtion f onnetion on the flue gs side All detils regrding length nd ross-setion in the following tles re only vlid in onnetion with the lned flue omponents offered in the Viessmnn prielist. Vitodens 00-W to 5 kw, Vitodens -F, Vitodens -W, Vitodens 4-F, Vitodens 00-W nd -F, Vitodens 4-F nd Vitosolr 00-F Internl dimeter Ø in mm Flue pipe Ventiltion ir pipe Vitodens 00-W, 45 to 60 kw Vitodens 00-W, 80 to 150 kw Plsti (PPs) lned flue system f routing through shft lned flue opertion (type 9x to TRGI 008) F lned flue opertion, oxil flue pipe (internl pipe f flue gs, externl pipe f omustion ir) is required s onnetion piee etween the Vitodens nd the shft. The onnetion piee is fitted to the oiler flue onnetion nd must ontin n inspetion pt. Note Gs ondensing oilers with totl rted heting output greter thn 50 kw my only e instlled in rooms tht provide ventiltion ir pertures to the outside, see pge 1. F instlltion through shfts duts with longitudinl ventiltion whih meet the requirements f himneys to DIN V hve fire rting of 90 minutes (L90), fire rting of 0 minutes (L0) f uildings in tegies 1 nd (mx. steys). Pri to instlltion, the relevnt flue gs inspet should hek tht the shft to e used is suitle nd pproved f this purpose. Shfts tht were previously onneted to oil solid fuel oilers must e thoughly lened y himney sweep. Loose deposits of sulphur nd soot must not remin on the inside of the himney. Running lned flue pipe through the shft is then not required. If though lening is impossile, if hlide deposits re present if the shft is silted up, seprte lned flue n e used inside the shft. lose off nd sel ny other onnetion pertures with pproprite mterils. This does not pply to ny lening inspetion pertures tht re provided with himney lening overs nd tht re identified with n pproprite test mrk. hek pri to instlltion whether the shft runs stright from top to ottom if it is offset (hek with mirrs). If the himney is offset, we reommend instlling flexile flue pipe (see pge 17). Inside the instlltion room, t lest one inspetion pt must e provided in the flue system f heking nd lening s well s f heking the pressure (if required). If the flue pipe is not essile from the roof, seond inspetion pt must e provided in the tti, ehind the himney lening hth. F further infmtion, see FeuVo [Germny]. Provide n inspetion pt t the se of the shft f heking the seondry ventiltion. Sfegurd the drining of the ondenste from the flue into the oiler y mintining n pproprite fll of t lest. The flue system must e routed to ove the roof (protrusion ove the roof ding to lol regultions). Alterntive E-designted flue pipes my e used, f exmple if lrger flue pipe dimeter is required, i.e. f greter flue lengths. The perfmne verifition to EN 184 should then e provided y the respetive flue mnufturer. If flue pipes other thn those offered s essies (whih re pproved with the Vitodens s single struturl unit) re used, the flue system must e heked f tightness y the flue gs inspet pri to ommissioning. In dne with the flue system pprovl ertifite, this my e rried out y mesuring the O O vlue inside the nnulr gp. If this test results in O ontent ove 0. % n O ontent lower thn 0.6 %, hek the flue system f tightness. Internl shft dimensions to DIN V Note Ading to the pprovl ertifite, internl shft dimensions smller thn those shown in the tles my lso e used f lned flue opertion, if this is indited y the perfmne verifition to EN 184. Minimum internl shft dimensions System size A Externl dimeter, fem. Minimum internl shft dimension onnetion Squre retngulr Round (sht side) Ø mm mm Ø mm (flexile, shft over PPs) (flexile, shft over metl) VIESMANN VITODENS AND VITOSOLAR

13 Design nd sizing infmtion f onnetion on the flue gs side (ont.) System size A Externl dimeter, fem. Minimum internl shft dimension onnetion Squre retngulr Round (sht side) Ø mm mm Ø mm (flexile, shft over PPs) (flexile, shft over metl) (flexile, shft over PPs) (flexile, shft over metl) Redued internl shft dimensions System size A Externl dimeter, fem. Redued internl shft dimension onnetion Squre retngulr Round (sht side) Ø mm mm Ø mm Minimum dimension of shfts in whih flue my e used without seprte lultion (positive pressure opertion). VITODENS AND VITOSOLAR VIESMANN 1

14 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Flue, system size 60, 80 nd 100 (omponents) (type 9x ding to TRGI 008) 1 A D A Ventiltion ir B Flue gs Inspetion pt D onnetion piee B 4 A System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Stndrd shft pk (PPs, rigid) omprising: Suppt end Suppt ril Shft over Spers (5 pe, mx. lerne 5 m) Stndrd shft pk (metl/pps, rigid) F twin flue himneys; one flue f solid fuel oilers omprising: Suppt end Suppt ril Shft over (metl) End pipe (stinless steel) Spers (5 pe, mx. lerne 5 m) Spers ( pe, mx. distne 5 m) Flue pipe 1.95 m long ( 1.95 m =.9 m) 1.95 m long (1 pe) m long (1 pe) m long (1 pe) Flue end (f use in elled shfts) 0 ( pe) 15 ( pe) 4 Inspetion piee, stright (1 pe) Blned flue inspetion piee, stright (1 pe) 6 Blned flue wll ezel Blned flue pipe m long 0.5 m long 8 Blned flue end (1 pe) 45 ( pe) Blned flue inspetion tee (1 pe) Blned flue inspetion end (1 pe) 9 Blned flue slide oupling Fixing lmp, white (1 pe) Stinless steel extension, 80 mm long f shft over, stndrd shft pk (metl/pps, rigid) Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Mx. totl length of the flue up to the oiler flue onnetion Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 5 *1 5 *1 5 *1 5 *1 *1 Alterntive system size. Blned flue dpt must e dered seprtely. 14 VIESMANN VITODENS AND VITOSOLAR

15 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Vitodens 00-W, from 45 kw Rted heting output rnge kw Mx. length - system size 80 m 0 15 Mx. length - system size 100 m 5 *1 0 * Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 17 *1 17 *1 0 *1 15 *1 The following omponents re tken into onsidertion f the mximum flue lengths: Blned flue onnetion pipe D 0.5 m long. 1 lned flue end 87 nd 1 suppt end 87 lned flue ends 45 nd 1 suppt end 87 Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue onnetion pipe 0.5 m long: 1 m Blned flue onnetion pipe 1 m long: m Blned flue ends 45 : 0.5 m Blned flue ends 87 : 1 m Blned flue inspetion tee: 1.5 m Note Oserve the speifitions regrding internl shft dimensions (see pge 1). F infmtion on routing type 6, see pge 4. Vitodens in onjuntion with solid fuel oilers Routing plsti flue djent to shft t risk of himney fire from soot (e.g. two drught himney with wood urning stove) is generlly permitted. Depending on the design of the himney top nd the opertion of the ondensing systems (open lned flue) different mesures re speified y the fire regultions. Design the room seled lned flue terminls so tht flue gs will not e drwn into the ir shft in dngerous mounts. Also ensure tht pressure flututions due to wind influene ffet the room seled lned flue shft s evenly s possile. F the required steps, see the following setions: Ø D A B D Lg 00 Open flue opertion nd/ ventiltion ir not eing supplied through the shft F fire sfety resons, the upper ption of omustile flue pipe terminls should e mde from non-omustile mterils. The length of flue pipe mde from non-omustile mterils, situted in re Lg nd proteted from therml rdition, must e t lest 00 mm. The length of the externl end pipe of the shft over must e no less thn externl dimeter D of the internl flue pipe. The stndrd shft pk (metl/pps) ontins stinless steel pipe (80 mm long). A stinless steel extension (80 mm long) is ville s n dditionl essy. E D F A Shft over, metl B End piee mde from non-omustile mteril Seondry ventiltion D Vitodens flue E himney used f solid fuel oiler F Minimum lerne to DIN V 18160, redued minimum lerne mximum lerne to EN (see pge 1) Blned flue opertion Ventiltion ir is supplied through the shft Design the room seled lned flue terminls so tht flue gs will not e drwn into the ir shft in dngerous mounts. Also ensure tht pressure flututions due to wind influene ffet the room seled lned flue system s evenly s possile. *1 Alterntive system size. Blned flue dpt must e dered seprtely. VITODENS AND VITOSOLAR VIESMANN 15

16 Design nd sizing infmtion f onnetion on the flue gs side (ont.) When using plsti shft over: The himney f the solid fuel oiler must stnd t lest 1000 mm proud of the Vitodens flue. F the himney extension, only use omponents tht re resistnt to soot fires. Ventiltion ir/seondry ventiltion D Vitodens flue (rigid flexile) E himney used f solid fuel oiler F Minimum lerne to DIN V 18160, redued minimum lerne mximum lerne to EN (see pge 1) A 1000 When using ommon downdrught plte: The flue end piee nd the shft over must e mde from nonomustile mteril (e.g. metl). B x D A Ø D B D E D F A himney extension mde from soot fire resistnt mteril B Shft over, plsti Ventiltion ir/seondry ventiltion D Vitodens flue E himney used f solid fuel oiler F Minimum lerne to DIN V 18160, redued minimum lerne mximum lerne to EN (see pge 1) When using metl shft over: The himney f the solid fuel oiler must stnd t lest x Ø D proud of the Vitodens flue. F the himney extension, only use omponents tht re resistnt to soot fires. A Ø D B x D F E G A himney extension mde from soot fire resistnt mteril B End piee mde from non-omustile mteril Shft over (on-site) D Ventiltion ir/seondry ventiltion E Vitodens flue F himney used f solid fuel oiler G Minimum lerne to DIN V 18160, redued minimum lerne mximum lerne to EN (see pge 1) The metl end piee nd shft over re prt of the stndrd shft pk (metl/pps). The stndrd shft pk (metl/pps) is ville s n essy. E D F A himney extension mde from soot fire resistnt mteril B Shft over, metl 16 VIESMANN VITODENS AND VITOSOLAR

17 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Flue, flexile, system size 60, 80 nd 100 (omponents) (type 9x ding to TRGI 008) A 1 9 qp D A Ventiltion ir B Flue gs Inspetion pt D onnetion piee B Note The flexile flue pipe should e routed t mx. ngle of 45 from the vertil. 5 4 A System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Stndrd shft pk (PPs, flexile) omprising: Suppt end Suppt ril Shft over Spers (5 pe, mx. lerne m) Stndrd shft pk (metl/pps, flexile) f twin flue himneys; one flue f solid fuel oilers omprising: Suppt end Suppt ril Shft over (metl) End pipe (stinless steel) Spers (5 pe, mx. lerne m) Spers (5 pe, mx. distne m) Flue pipe, flexile, s m roll 4 onnetion piee f onneting residul lengths of the flexile flue pipe 5 Inspetion piee, stright, f instlltion into the flexile flue pipe Pipe lowering tthment with m rope 6 Blned flue inspetion piee, stright (1 pe) 7 Blned flue wll ezel Blned flue pipe m long 0.5 m long 9 Blned flue end (1 pe) 45 ( pe) Blned flue inspetion tee (1 pe) Blned flue inspetion end (1 pe) qp Blned flue slide oupling Fixing lmp, white (1 pe) Stinless steel extension, 80 mm long, f shft over, stndrd shft pk (metl/pps, flexile) Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 70/110 mm 80 Ø 80/15 mm to Ø 100/150 mm Mx. totl flue length up to the oiler flue onnetion with flexile flue pipe Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 5 *1 5 *1 5 *1 5 *1 *1 Alterntive system size. Blned flue dpt must e dered seprtely. VITODENS AND VITOSOLAR VIESMANN 17

18 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Vitodens 00-W, from 45 kw Rted heting output rnge kw Mx. length - system size 80 m 0 15 Mx. length - system size 100 m *1 17 * Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 16 *1 16 *1 18 *1 1 *1 The following omponents re tken into onsidertion f the mximum flue lengths: Blned flue onnetion pipe D 0.5 m long. 1 lned flue end 87 nd 1 suppt end 87 lned flue ends 45 nd 1 suppt end 87 Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue onnetion pipe 0.5 m long: 1 m Blned flue onnetion pipe 1 m long: m Blned flue ends 45 : 0.5 m Blned flue ends 87 : 1 m Blned flue inspetion tee: 1.5 m Note Oserve the speifitions regrding internl shft dimensions (see pge 1). F infmtion on routing type 6, see pge 4.. Plsti (PPs) lned flue system f vertil routing through pithed flt roof (type x, to TRGI 008) F vertil roof outlets when the Vitodens is instlled in ttis The roof outlet my only e used where the eiling of the living spe lso fms prt of the roof only the roof struture is loted ove the eiling (pithed tti). Note Instll ondensing oilers with heting output > 50 kw in seprte nd ventilted instlltion room (ding to FeuVo [Germny]) (Vitodens 00-W from 60 kw). Flues mde from omustile mterils nd instlled in uildings must either e routed through shfts e equipped with protetive pipes mde from non-omustile mterils omprle protetive over mde from non-omustile mterils. The flue my lso e routed ehind jm wll solid wll of onverted tti, provided the fire protetion lss of the jm wll responds to tht of the eiling (e.g. B0). Minimum lernes to omustile mterils inside the instlltion room in onnetion with the roof outlet re not required. As prt of the E pprovl test it ws verified tht no surfe tempertures on the Vitodens its lned flue system will exeed 85. Instll n inspetion pt f heking nd lening the flue pipe inside the instlltion room. The vertil roof outlet hs een tested nd E-designted s onentri lned flue system s single struturl unit with the Vitodens ondensing oiler. A perfmne verifition ding to EN 184 is not required. Vertil flt roof outlet Integrte the flt roof ollr into the roof skin ding to the flt roof guidelines (see pge 58). Push the roof outlet into the roof from ove nd position it on the flt roof ollr. Note The following minimum mesurements pply to the dimeter of the eiling perture: System size Ø 60 mm: 105 mm System size Ø 80 mm: 10 mm System size Ø 100 mm: 160 mm Ensure the instlltion hs een ompleted efe seuring the roof outlet on site with lmp. When instlling severl vertil roof outlets djent to eh other, mintin minimum lernes of 1.5 m etween outlets nd towrds other omponents, in dne with FeuVo [Germny] [ lol regultions]. Note Seprte ove-roof extensions re ville if the length of 400 mm ove the roof line nd vertil to the roof surfe is insuffiient due to speifi requirements (see following tle). Approvl with the flue system is ensured. *1 Alterntive system size. Blned flue dpt must e dered seprtely. 18 VIESMANN VITODENS AND VITOSOLAR

19 Design nd sizing infmtion f onnetion on the flue gs side (ont.) A 1 B A Ventiltion ir B Flue gs Inspetion pt A B System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue roof outlet with fixing lmp olour: lk olour: terrott Aove roof extension with lmp (re on site) olour: lk 0.5 m long m long, with ring lmp olour: terrott 0.5 m long m long, with ring lmp Universl roof tile F Romn tiles, pntiles, plin tiles, slte nd other types of roof over olour: lk terrott Flt roof ollr Pipe outlet f Klöer roof tiles olour: lk terrott (provide the responding Klöer roof tile on site to mth the roof outlet seleted f the prtiulr type of roof over) 4 Blned flue inspetion piee, stright (1 pe) 5 Blned flue slide oupling Universl over plte Blned flue end (1 pe) 45 ( pe) Blned flue pipe m long 0.5 m long Fixing lmp, white (1 pe) Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 1 *1 1 *1 1 *1 11 *1 Min. mm Vitodens 00-W, from 45 kw Rted heting output rnge kw Mx. length - system size 80 m 10 6 Mx. length - system size 100 m 1 *1 9 * Min. mm Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 1 *1 1 *1 1 *1 11 *1 Min. mm x 87 lned flue ends re tken into onsidertion f the mximum flue lengths. *1 Alterntive system size. Blned flue dpt must e dered seprtely. VITODENS AND VITOSOLAR VIESMANN 19

20 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue ends 45 : 0.5 m Blned flue ends 87 : 1 m Blned flue inspetion tee: 1.5 m.4 Plsti (PPs) lned flue system f externl wll onnetion (type 1x to TRGI 008) As prt of the E pprovl test it ws verified tht no surfe tempertures on the Vitodens its lned flue system will exeed 85. Oserve the implementtion infmtion to TRGI 008, in prtiulr the rrngement/position of the wll terminl. Instll the onneting pipe with minimum fll of towrds the oiler. Instll n inspetion pt in the flue f heking nd lening the flue pipe. The externl wll onnetion hs een tested nd E-designted s onentri lned flue system s one struturl unit with the Vitodens ondensing oiler. A perfmne verifition ding to EN 184 is not required A Ventiltion ir B Flue gs Inspetion pt A 7 B System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue externl wll onnetion (inl. wll ezels) Blned flue pipe m long 0.5 m long 4 Blned flue end (1 pe) 45 ( pe) Blned flue inspetion end, 87 ( pe) 5 Blned flue inspetion piee, stright (1 pe) 6 Blned flue slide oupling Grille Required if the omustion ir inlet nd flue outlet re positioned up to m ove ground level in puli privte thoughfres Fixing lmp, white (1 pe) Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 1 *1 1 *1 1 *1 11 * Mx. length - system size 100 m 1 *1 1 *1 1 1 Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 1 *1 1 *1 1 *1 11 *1 x 87 lned flue ends re tken into onsidertion f the mximum flue lengths. Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue ends 45 : 0.5 m Blned flue ends 87 : 1 m Blned flue inspetion tee: 1.5 m *1 Alterntive system size. Blned flue dpt must e dered seprtely. 0 VIESMANN VITODENS AND VITOSOLAR

21 Design nd sizing infmtion f onnetion on the flue gs side (ont.).5 Plsti (PPs) flue/ventiltion ir system f seprte ventiltion ir nd flue gs routing (type 8x to TRGI 008) The Vitodens my e operted in lned flue mode nd with seprtely routed flue gs nd ventiltion ir, sujet to the flue system meeting the following onditions: onnetion to himney tht is unsuitle f providing the omustion ir supply euse of deposits. onnetion to moisture-resistnt himney. The omustion ir is then supplied through seprte ventiltion ir pipe tht is routed seprtely from the flue pipe. Oserve the design infmtion ding to TRGI 008. Internl dimeter, flue pipe: Ø mm Internl dimeter, externl pipe: Ø mm Internl dimeter, ventiltion ir pipe: Ø 100 mm Mx. pipe length: onnetion piee: m Ventiltion ir pipe: 4 m Mx. numer of ends (flue pipe nd ventiltion ir pipe): 87 : pe eh 45 : pe eh Instll n inspetion pt in the flue f heking nd lening the flue pipe. Sfegurd the drining of the ondenste from the flue into the oiler y mintining n pproprite fll of t lest. As prt of the E pprovl test it ws verified tht no surfe tempertures on the Vitodens its lned flue system will exeed 85. The flue system f seprte ventiltion ir nd flue gs routing hs een tested s single struturl unit with the Vitodens ondensing oiler. A perfmne verifition ding to EN 184 f the ventiltion ir side nd the onnetion piees is not required. 7 A 4 m mm 5 A Ventiltion ir B Flue gs Inspetion pt D onnetion piee E Ventiltion perture F Shft F90/L90 F0/L0 G Flue D 4 5 E G B F Boiler flue onnetion (prt of the stndrd oiler delivery) nd Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Blned flue pipe 1 m long 0.5 m long Blned flue end 87 (1 pe) 45 ( pe) System size Ø mm 60/100 80/ Blned flue slide oupling Blned flue inspetion piee, stright (1 pe) Blned flue tee 8 with wll ezels Ventiltion ir pipe Ø 100 mm 1 m long (my e trimmed to size) 0.5 m long (my e trimmed to size) Ventiltion ir end Ø 100 mm 87 (1 pe) 45 ( pe) Ventiltion ir grille Fixing lmp, white (1 pe) (lned flue pipe) Note Where the flue pipe is routed through n existing himney shft (not moisture-resistnt), use the flue pipe omponents ding to pge 14. Mx. totl length of the flue up to the oiler flue onnetion Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 5 *1 5 *1 5 *1 5 *1 *1 Alterntive system size. Blned flue dpt must e dered seprtely. VITODENS AND VITOSOLAR VIESMANN 1

22 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Vitodens 00-W, from 45 kw Rted heting output rnge kw Mx. length - system size 80 m 0 15 Mx. length - system size 100 m 5 *1 0 * Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 17 *1 17 *1 0 *1 15 *1 The following omponents re tken into onsidertion f the mximum flue lengths: onnetion pipe D 0.5 m long. 1 end 87 nd 1 suppt end 87 ends 45 nd 1 suppt end 87 Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: onnetion pipe 0.5 m long: 0.5 m onnetion pipe 1 m long: 1 m Bend 45º: 0. m Bend 87º: 0.5 m Inspetion tee: 0. m.6 Plsti (PPs) lned flue system f routing over externl wlls (type 5x, to TRGI 008) The Vitodens my lso e onneted to flue tht is routed over n externl wll without shft. The omustion ir is drwn in vi the ir inlet piee. The vertil externl pipe provides protetion, nd due to the stti ir gp inside lso ts s therml insultion. Sfegurd the drining of the ondenste from the flue into the oiler y mintining n pproprite fll of t lest. The externl wll flue hs een tested nd E-designted s onentri lned flue system s single struturl unit with the Vitodens ondensing oiler. A perfmne verifition ding to EN 184 is not required. *1 Alterntive system size. Blned flue dpt must e dered seprtely. VIESMANN VITODENS AND VITOSOLAR

23 Design nd sizing infmtion f onnetion on the flue gs side (ont.) qq A 1 9 qp 7 D qp.0 m 4 5 qw.5 m A A Flue gs B Ventiltion ir Inspetion pt D Elow in the externl wll flue, see pge 48 qq 6 qe qr 8 B 7 8 *1 Alterntive system size. Blned flue dpt must e dered seprtely. System size Ø mm 1 Boiler flue onnetion (prt of the stndrd oiler delivery) Blned flue inspetion tee º (1 pe) Blned flue inspetion end, º (1 pe) Blned flue inspetion piee, stright (1 pe) nd Blned flue end 87º (1 pe) Blned flue slide oupling Blned flue pipe m long (1 pe) 1 m long (1 pe) 0.5 m long (1 pe) 5 Wll ezel Fixing lmp, white (1 pe) 7 Blned flue inspetion piee, stright (1 pe) Externl wll inspetion piee, 100 stright (1 pe) 8 Externl wll pk omprising: Blned flue end Blned flue ir inlet piee Wll ezel 9 Externl wll terminl F sht roof overhng qp Blned flue end 87º (1 pe) º ( pe) Externl wll end 87º (1 pe) º ( pe) 100 qq Blned flue pipe 1.95 m long (1 pe) m long (1 pe) m long (1 pe) Externl wll pipe 1.95 m long (1 pe) m long (1 pe) m long (1 pe) 100 qw Universl over pltes qe Blned flue roof outlet Externl wll with fixing lmps (f lrge roof overhng) olour: lk terrott Aove roof extension with lmp (re on site) olour: lk 0.5 m long m long olour: terrott 0.5 m long m long qr Universl roof tile F Romn tiles nd pntiled roofs. olour: lk terrott VITODENS AND VITOSOLAR VIESMANN

24 Design nd sizing infmtion f onnetion on the flue gs side (ont.) F plin tile, slte nd other roof overs. olour: lk terrott System size Ø mm Pipe outlet f Klöer roof tiles olour: lk terrott (provide the responding Klöer roof tile on site to mth the roof outlet seleted f the prtiulr type of roof over) System size Ø mm Blned flue dpt Ø 80/15 mm to Ø 60/100 mm Ø 60/100 mm to Ø 80/15 mm Ø 80/15 mm to Ø 100/150 mm Mx. totl length of the flue pipe Vitodens 00-W, -F, -W nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 5 *1 5 *1 5 *1 0 *1 Vitodens 00-W, from 45 kw Rted heting output rnge kw Mx. length - system size 80 m 1 1 Mx. length - system size 100 m 17 *1 17 * Vitodens 00-W, -F nd 4-F Rted heting output rnge kw Mx. length - system size 60 m Mx. length - system size 80 m 15 *1 15 *1 15 *1 1 *1 x 87º lned flue ends re tken into onsidertion f the mximum flue lengths. Sutrt dditionl ends, tees nd stright lengths from the mximum length using the following vlues: Blned flue end 45º: 0.5 m Blned flue end 87º: 1 m Blned flue inspetion tee: 1.5 m.7 Plsti (PPs) lned flue system f routing through lightweight shft A spe sving shft f redued temperture requirements my e retrofitted if no shft is ville nd the Vitodens is instlled in the living spe with one me full steys ove. "UNIFIX" shft profiles offered y Skoerne (mde from erted onrete) The shft used must omply with the requirements f domesti himneys to DIN V must e generlly pproved y the uilding inspette [Germny]. Ø mm Fire rting mm mm min min min min Ø "SKOBIFIXnno" nd "SKOBIFIXXs 0" shft profiles offered y Skoerne (mde from fomed ermis) Fire rting 0 min. *1 Alterntive system size. Blned flue dpt must e dered seprtely. 4 VIESMANN VITODENS AND VITOSOLAR

25 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Ø 60 Ø 80 A [Germn] uilding inspette pproved shft system mde from reeze onrete fomed ermis is ville from Skoerne. Address f Skoerne: Skoerne Shnsteinsysteme GmH Ostendstrsse 1 D-6419 Pfungstdt Anhing f roof outlets with shft profiles (Where the shft is run up to the roof skin) A B Aville from Skoerne: A Roof outlet B Universl roof tile Terminl shft profile D Anhing of the roof outlet During instlltion, mth the terminl shft profile to the roof slope. D Shft profiles offered y Promt System size Ø mm mm mm mm d mm Fire rting min min d A PROMATET femle onnetion B PROMATET profile Flue System size Ø mm mm mm mm d mm Fire rting min min VITODENS AND VITOSOLAR VIESMANN 5

26 Design nd sizing infmtion f onnetion on the flue gs side (ont.) A B A [Germn] uilding inspette pproved shft system mde from lium silite fire-resistnt pltes is ville from Promt nd other suppliers. Address f Promt: Promt GmH Postfh D-4085 Rtingen 100 A PROMATET femle onnetion B PROMATET profile Flue Roof outlet f shfts with Promt profiles During instlltion, mth the terminl shft profile to the roof slope. A B A Vertil oxil roof outlet (lned flue system) B Universl roof tile Lightweight shft mde from PROMATET minerl fire profiles.8 Plsti (PPs) lned flue system f routing multiple pipes through shft It is possile to route severl flues f lned flue opertion through ommon, suffiiently sized shft. F this, the Vitodens ondensing oilers must e instlled in the sme living spe. F resons of fire protetion, they nnot e instlled nd onneted on different levels in different rooms. The flue suppts inside the shft nd the shft over must e retly implemented on site. F lned flue omponents from the Vitodens to the ommon shft, see pge VIESMANN VITODENS AND VITOSOLAR

27 Design nd sizing infmtion f onnetion on the flue gs side (ont.) A Ventiltion ir B Flue gs Inspetion pt Lyout exmples Minimum lernes of the individul flues in dne with DIN V : In squre/retngulr shfts: 0 mm In round shfts: 0 mm d System size Dimensions [mm] Ø mm d Note Ading to the pprovl ertifite, internl shft dimensions smller thn those shown in the tle my lso e used, provided it is indited y the perfmne verifition to EN Plsti (PPs) lned flue system (onnetion pipe) f onneting multiple flues to single room seled lned flue system The Vitodens ondensing oilers meet the sfety requirements in dne with DIN A generl Building Regultions pprovl is therefe not required f onnetion to room seled lned flue. When onneting two ondensing oilers to one himney on the sme flo, the onnetion piee inlets should e seprted y t lest 00 mm. Design nd lultions f room seled lned flue systems with multiple onnetions re rried out y the relevnt mnufturer. VITODENS AND VITOSOLAR VIESMANN 7

28 Design nd sizing infmtion f onnetion on the flue gs side (ont.) Room seled lned flue system, negtive pressure (type 4x, to TRGI 008) H min. H mx. H Room seled lned flue systems f negtive pressure my, f exmple, e otined from the following mnufturers: ek Edelsthlkmin GmH D-9569 Untersteinh Jeremis Shnstein Systeme Opfenrieder Str. 1 D Wssertrüdingen Plew-Werke GmH D-5466 Speiher/Eifel Shiedel GmH & o, Huptverwltung Lerhenstrsse 9 D Munih Wienererger GmH Oldenurger Allee 6 D-0659 Hnnover A Effetive himney height reltive to the highest positioned Vitodens B Ventiltion ir Flue gs D Room seled lned flue system (see elow f mnufturers) E Inspetion pt F Pressure ompenstion perture G hek with the flue system mnufturer regrding minimum lernes. Room seled lned flue system, positive pressure multiple onnetion with the Vitodens 00-W, - W nd -F up to 6 kw (type 4x to TRGI 008) System f lned flue opertion, speifilly developed f the Vitodens 00-W, -W nd -F. Minimum shft ross-setion: Squre: mm Round: Ø 195 mm. Up to 5 Vitodens 00-W, -W nd -F ( 4 Vitodens kw) with the sme rted heting output n e onneted to one flue system. Vitodens with different rted heting output levels n e onneted to the system if the relevnt lultions re verified. F this, plese omplete the enquiry fm on pge 0. 8 VIESMANN VITODENS AND VITOSOLAR

29 Design nd sizing infmtion f onnetion on the flue gs side (ont.) 4 1 B D D 8 m D A qp 9 qq qw.5 m 15 m System size Ø mm 1 Boiler flue onnetion (prt of the stndrd 80 oiler delivery) Flue gs non-return devie F instlltion in the Vitodens 00-W, -W nd -F (up to 6 kw) Order seprtely f every oiler Stndrd shft pk (PPs, rigid) 100 omprising: Suppt end Suppt ril Shft over (PPs) Spers ( pe) Spers ( pe) 100 Blned flue end 87º (1 pe) 80 45º ( pe) 80 Blned flue inspetion end 80 87º (1 pe) 4 Blned flue dpt 80 Ø 60/100 to Ø 80/15 5 Blned flue inspetion piee, stright 80 (1 pe) 6 Blned flue slide oupling 80 Fixing lmp, white (1 pe) (lned flue 80 pipe) 7 Wll ezel 80 8 Blned flue pipe 1 m long m long 80 9 onneting ssemly, multiple onnetion 100 omprising: Boiler oding rd Inspetion pipe Ø 100 Flue gs onnetion Ø 80 Fixing lmp Sper Long fem. onnetion Ø 100 qp onneting ssemly, ondenste drin 100 D qr E A Flue gs B Ventiltion ir ondenste drin into vertil flue D Inspetion pt E ondenste drin with siphon qe omprising: Brnh 87 Ø 40 Fixing lmp Long fem. onnetion Ø 100 qq onneting lmp required f every joint 100 in the shft qw Flue pipe m long ( m = 4 m) 100 m long (1 pe) m long (1 pe) m long (1 pe) 100 Flue end (F use in elled shfts) 0º ( pe) º ( pe) 100 qe Inspetion piee, stright (1 pe) 100 qr ondenste drin onnetion (eentri) 100 Reduer from Ø 100 mm to Ø 40 mm VITODENS AND VITOSOLAR VIESMANN 9