Vehicle Application Guide...

Transcription

1 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The FORD6 firmware for DBALL is an all-in-one door lock and override module compatible with specific Ford and Lincoln vehicles. The optional Plug & Play T-Harness THFD (sold separately) provides simpler and faster installation. Two () keys are required for programming the module. This module can only be flashed and configured using XpressVIP at or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on page n for more information. Index Vehicle Application Guide... 0 Installation (Wiring Diagrams & Vehicle Wiring Reference Charts) Type without T-Harness... Type with T-Harness (THFD)... Type without T-Harness... Type with T-Harness (THFD)... Programming Module Programming... Module Programming - keys required... Module Reset... Hard Reset... Feature & Option List... Feature Programming LED Diagnostics & Troubleshooting... Limited One-Year Consumer Warranty... Quick Reference Guide Ford is a registered trademark and property of the Ford Motor Company.

2 Vehicle Application Guide Page The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security Ford Edge D D D Edge (SA Key) D D D Escape D D Escape Hybrid D D E-Series (SA Key) D D D Expedition (SA Key) [] D D D Explorer (SA Key) D D D F50 (SA Key) D D D F50 D D D F50 (SA Key) D D D F50 D D D F50 (SA Key) D D D F50 (SA Key) D D D Flex D D D Flex (SA Key) D D D Fusion (SA Key) D D D Mustang (SA Key) D D D Taurus (SA Key) D D D Lincoln Navigator [] D D D DL-Door Lock Control DL-Door Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-RAP Shut Down (Retained ACC Power) RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Driver Door Pin SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status [] Ford Expedition and Lincoln Navigator are NOT compatible with optional T-Harness THFD. Legend: DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status

3 Type without T-Harness Page Refer to the Wiring Reference Chart for more information on specific wiring and connections. (-) Hood Input (+) Brake Input [] (AC) Tach Input (-) Door Status Input (-) E-Brake Status Input (-) Ground (-) Ground (+) Accessory Output (+) Starter Output (+) V (+) Ignition Output Remote Starter (-) Lock Output (-) Unlock Output (-) Trunk Output (-) GWR (Status) (-) Parking Lights Output (+) V 87 87a (+) Accessory (+) Starter (+) V Headlight Switch Connectors (see Wiring Reference Chart) Parking Light (+) Keysense (-) Trunk Input (-) Unlock (-) Lock Connect to Vehicle Refer to the section Wiring Reference Chart for more information. 5 7 Headlight Switch Ground Driver Door Trigger (+) Ignition (+) V MS CAN High: pin OBDII Diagnostic Connector MS CAN Low: pin TX: pin P.A.T.S. pin (at ignition switch) RX: pin (+) V (-) Ground MS CAN High: Tan/Black: MS CAN Low: Tan: (+) V: Brown: 7 (+) Ignition Output: Yellow: 8 RAP Off: Orange/Red: 0 RAP Off: Yellow/Red: (+) V: Red: (-) Ground: Black: (-) E-Brake Status Output: Black/White: (-) Lock Activation Output: Green/Black: (-) Door/Trunk Status Output: Green/White: (-) Unlock Activation Output: Red/Black: [] (AC) Tach Output: Violet/White: 5 (+) Brake Output: Gray: 6 (+) Accessory/Keysense Output: Gray/Black: 7 (-) Trunk Activation Output: Violet/Brown: 9 Data TX: Yellow/Black: 0 Data RX: Orange/Black: (-) Hood Status Output: Blue/Red: RF Prog. Button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input : Red/White: (-) Trunk Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+)V RX (-) Ground TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).

4 [] Type with T-Harness (THFD) Refer to the Wiring Reference Chart for more information on specific wiring and connections. Ignition Barrel DD only Page Headlight Switch Connectors 7 (see Wiring Reference Chart) 5 6 Ignition Switch (connector side) 5 7 Headlight Switch Ground (-) Parking Lights Headlight Ground (cut - vehicle side) :Yellow Headlight Ground (cut - switch side) :Orange/White (-) Parking Light Output :White P.A.T.S. -pin Connector (connector side) (+) V (-) Parking Lights (-) Ground Starter Remote [](AC) Tach (+) Ignition Blue/Red (pull this wire from the webbing of the T-Harness, and cut it.) Remote Start Safety Override Switch is inactive (used for RSR only) (-) E-Brake Status Input (+) Start Violet Attention! Cut loop in N O N - R S R application. OBDII Diagnostic Connector MS CAN High: pin [](AC) Tach Output: Violet/White (+) Ignition: Pink (+) Starter: Violet MS CAN Low: pin [] THFD Rev. (Optional T-Harness) (+) V Connect to Vehicle Refer to the section Wiring Reference Chart for more information. Driver Door Trigger (-) Lock (-) Unlock (-) Trunk MS CAN High: Tan/Black RAP Off: Orange/Red RAP Off: Yellow/Red (-) Lock Activation Output: Green/Black (-) Unlock Activation Output: Red/Black MS CAN Low: Tan (-) E-Brake Status Output: Black/White (-) Trunk Activation Output: Violet/Brown RF Prog. Button LED DBALL/ DBALL 0 Do not connect (+)V RX (-) Ground TX Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. [] T-Harness is NOT compatible with the Ford Expedition or Lincoln Navigator. With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise). XKDD65

5 Type - Vehicle Wiring Reference Chart Page 5 Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford E-Series 0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB front passenger side of the center console. Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB front passenger side of the center console. Gray 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Blue 7 Negative Headlight switch Gray 0-pin Parking Light Blue/Gray 5 Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin Ford Escape 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB front passenger side of the center console. Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB front passenger side of the center console. Gray 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Blue 7 Negative Headlight switch Gray 0-pin Parking Light Blue/Gray 5 Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin Ford Escape Hybrid 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB front passenger side of the center console. Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB front passenger side of the center console. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB front passenger side of the center console. Gray 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Blue 7 Negative Headlight switch Gray 0-pin Parking Light Blue/Gray 5 Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin

6 Type - Vehicle Wiring Reference Chart (continued) Page 6 Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford Expedition 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB in passenger kick panel. Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB in passenger kick panel. Gray 6-pin Power Liftgate Gray/Yellow 7 Negative Power liftgate switch. Black 8-pin Lock White/Brown 7 Negative BCM/SJB in passenger kick panel. Gray 6-pin Unlock Blue/Brown Negative BCM/SJB in passenger kick panel. Gray 6-pin Start Blue/White 0 Positive Ignition switch Gray 0-pin Ignition White/Orange Positive Ignition switch Gray 0-pin Accessory Brown/Yellow 7 Positive Ignition switch Gray 0-pin Accessory Violet/Green 5 Positive Ignition switch Gray 0-pin Keysense Blue/Gray Positive Ignition switch Gray 0-pin Headlight Switch Ground Black/White 7 Negative Headlight switch Gray 0-pin Parking Light Blue/Gray 5 Negative Headlight switch Gray 0-pin RX Blue/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Brown Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red 9 Positive Ignition switch Gray 0-pin Ford F MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Trunk/Hatch Release N/A N/A N/A N/A N/A N/A Lock Blue/Green 6 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red Positive Ignition switch Black 7-pin Ford F MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Trunk/Hatch Release N/A N/A N/A N/A N/A N/A Lock Blue/Green 6 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Gray Negative Headlight switch Gray 0-pin Parking Light Yellow/Orange Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red or Blue/Red Positive Ignition switch Black 7-pin

7 Type - Vehicle Wiring Reference Chart (continued) Page 7 Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford F MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Trunk/Hatch Release N/A N/A N/A N/A N/A N/A Lock Blue/Green 6 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Gray Negative Headlight switch Gray 0-pin Parking Light Yellow/Orange Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red or Blue/Red Positive Ignition switch Black 7-pin Ford F MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Trunk/Hatch Release N/A N/A N/A N/A N/A N/A Lock Blue/Green 6 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Gray Negative Headlight switch Gray 0-pin Parking Light Yellow/Orange Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red or Blue/Red Positive Ignition switch Black 7-pin Ford Flex MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB under driver dash. Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB under driver dash. Gray 6-pin Power Liftgate Gray/Yellow 6 Negative Power liftgate switch. Black 6-pin Lock Blue/Green 7 Negative BCM/SJB under driver dash. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB under driver dash. Gray 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Blue Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin

8 Type - Vehicle Wiring Reference Chart (continued) Page 8 Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford Flex 0-05 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Violet 9 Open BCM/SJB under driver dash. Black 6-pin Trunk/Hatch Release Brown Negative BCM/SJB under driver dash. Black 6-pin Power Liftgate Gray 6 Negative Power liftgate switch. Brown 6-pin Lock Blue 6 Negative BCM/SJB under driver dash. Black 6-pin Unlock Yellow 8 Negative BCM/SJB under driver dash. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Accessory Violet 6 Positive Ignition switch Black 7-pin Keysense Blue 5 Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Blue Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Violet Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow Data P.A.T.S. connector at ignition switch. Black -pin (+)V Red 6 Positive BCM/SJB under driver dash. White -pin Ford Fusion 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB under driver dash. Gray 6-pin Trunk/Hatch Release Brown/Yellow 0 Negative BCM/SJB under driver dash. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB under driver dash. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB under driver dash. Gray 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Violet Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin Ford Mustang 0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Trunk/Hatch Release Brown/Yellow or Brown/Violet 0 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Ignition Gray/Violet Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Violet Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin

9 Type - Vehicle Wiring Reference Chart (continued) Page 9 Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford Mustang 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet Open BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Trunk/Hatch Release Brown/Yellow or Brown/Violet 0 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Lock Blue/Green 7 Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Unlock Yellow/Violet Negative BCM/SJB in passenger kick panel or at driver kick panel harness. Gray 6-pin Ignition Gray/Violet Positive Ignition switch Black 7-pin Headlight Switch Ground Black/Violet Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin TX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin (+)V Blue/Red Positive Ignition switch Black 7-pin Ford Taurus 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open BCM/SJB under driver dash. Black 6-pin Trunk/Hatch Release Brown/Yellow or Negative BCM/SJB under driver dash. Black 6-pin Lock Blue/Green 6 Negative BCM/SJB under driver dash. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB under driver dash. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground Black/White Negative Headlight switch Gray 0-pin Parking Light Gray Negative Headlight switch Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Red 6 Positive BCM/SJB under driver dash. White -pin Lincoln Navigator 0-0 MS CAN High Gray/Orange Data OBDII Diagnostic Connector Black 6-pin MS CAN Low Violet/Orange Data OBDII Diagnostic Connector Black 6-pin Driver Door Trigger Green/Violet N.C. BCM/SJB in passenger kick Gray 6-pin Trunk/Hatch Release Brown 7 Negative BCM/SJB in passenger kick Gray 6-pin Power Liftgate Gray/Yellow 7 Negative Power liftgate switch Black 8-pin Lock White/Brown 7 Negative SJB in passenger kick Gray 6-pin Unlock Blue/Brown Negative SJB in passenger kick Gray 6-pin Start Blue/White 0 Positive Ignition Switch Gray 0-pin Ignition White/Orange Positive Ignition Switch Gray 0-pin Accessory Brown/Yellow 7 Positive Ignition Switch Gray 0-pin Accessory Violet/Green 5 Positive Ignition Switch Gray 0-pin Keysense Blue/Gray Positive Ignition Switch Gray 0-pin Headlight Switch Ground Black/White 7 Negative Headlight Switch Gray 0-pin Parking Lights Blue/Gray 5 Negative Headlight Switch Gray 0-pin RX Blue/Gray Data PATS connector at ignition switch Black -pin TX Violet/Brown Data PATS connector at ignition switch Black -pin (+) V Blue/Red 9 Positive Ignition Switch Gray 0-pin

10 Type without T-Harness Page 0 Refer to the Wiring Reference Chart for more information on specific wiring and connections. (+) Ignition: White/Orange, pin (+) Accessory: Violet/Green, pin 6 (+) Keysense: Blue/Gray, pin 5 Ignition Switch (+) Starter: Blue/White, pin 7 (+) V: Green/Red, pin (-) Ground (-) Hood Input (+) Brake Input [](AC) Tach Input (-) Door Status Input (-) E-Brake Status Input (-) Ground (+) Accessory Output (+) Starter Output (+) V (+) Ignition Input/Output Starter Remote (-) Lock Output (-) Unlock Output (-) Trunk Output (-) GWR (Status) (+) Parking Lights Output (+) Parking Lights: Yellow/Blue, pin 6 BCM Gray 0 pin Connector (-) Trunk Release: Brown, pin (Ford Edge only) (-) Unlock: Yellow/Violet, pin 8 (-) Lock: Blue/Green, pin BCM C80C 6 pin Connector Driver Door Trigger: Green/Violet, pin 9 (+) Ignition (+) V Trunk Release 8-pin Connector (Ford Explorer only) MS CAN High: Gray/Orange, pin 8 OBDII Diagnostic Connector Ford Explorer 0+. OR Ford Edge 0+. (-) Power Liftgate: Gray/Yellow, pin MS CAN Low: Violet/Orange,pin TX: Yellow/Orange, pin P.A.T.S. pin (at ignition switch) RX: Violet/Gray, pin MS CAN High: Tan/Black: MS CAN Low: Tan: (+) V: Brown: 7 (+) Ignition Output: Yellow: 8 RAP Off: Orange/Red: 0 RAP Off: Yellow/Red: (+) V (+) V: Red: (-) Ground (-) Ground: Black: (-) E-Brake Status Output: Black/White: (-) Lock Output: Green/Black: (-) Door/Trunk Status Output: Green/White: (-) Unlock Output: Red/Black: [](AC) Tach Output: Violet/White: 5 (+) Brake Output: Gray: 6 (+) Accessory/Keysense Output: Gray/Black: 7 (-) Trunk Release Output: Violet/Brown: 9 TX: Yellow/Black: 0 RX: Orange/Black: (-) Hood Status Output: Blue/Red: RF Prog. Button LED DBALL/ DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input : Red/White: (-) Trunk Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+)V RX (-) Ground TX XKDD65 Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise).

11 Type with T-Harness (THFD) Refer to the Wiring Reference Chart for more information on specific wiring and connections. Ignition Barrel Page DD only (+) Parking Lights: Yellow/Blue, pin 6 Ignition Switch (connector side) BCM Gray 0 pin Connector (driver kick panel or driver end of dash) (+) V Yellow (+) Parking Light Output: White P.A.T.S. -pin Connector (connector side) (+) V (-) Parking Lights (-) Ground Starter Remote [] (AC) Tach (+) Ignition Blue/Red (pull this wire from the webbing of the T-Harness, and cut it.) Remote Start Safety Override Switch is inactive (used for RSR only) (-) E-Brake Status Input (+) Start Violet Attention! Cut loop in N O N - R S R application. MS CAN High: Gray/Orange, pin [] (AC) Tach Output: Violet/White (+) Ignition: Pink (+) Starter: Violet (+) V OBDII Diagnostic Connector MS CAN Low: Violet/Orange, pin Connect to Vehicle Refer to the section Wiring Reference Chart for more information Driver Door Trigger (-) Lock (-) Unlock (-) Trunk MS CAN High: Tan/Black RAP Off: Orange/Red RAP Off: Yellow/Red THFD Rev. (Optional T-Harness) (-) Lock Activation Output: Green/Black MS CAN Low: Tan (-) E-Brake Status Output: Black/White (-) Unlock Activation Output: Red/Black (-) Trunk Activation Output: Violet/Brown RF Prog. Button LED DBALL/ DBALL 0 Do not connect (+)V RX (-) Ground TX Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. With the exception of the OBDII Diagnostic connector, all connectors are displayed from the wire side (unless specified otherwise). XKDD65

12 Type - Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color No. Pin Ford Explorer 0-05 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open to N.C BCM/SJB under driver dash. Black 6-pin Trunk/Hatch Release Brown Negative BCM/SJB under driver dash. Black 6-pin Parking Lights Yellow/Blue 6 Positive BCM/SJB under driver dash. Gray 0-pin Power Liftgate Gray/Yellow 7 Negative Power liftgate switch. Black 8-pin Lock Blue/Green 6 Negative BCM/SJB under driver dash. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB under driver dash. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground N/A N/A N/A N/A N/A N/A Parking Light Yellow/Blue 6 Positive BCM/SJB under driver dash. Gray 0-pin RX Violet/Red or Violet Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange or Yellow Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red Positive Ignition switch Black 7-pin Ford Edge 0-0 MS CAN High Gray/Orange Data OBDII diagnostic connector. Black 6-pin MS CAN Low Violet/Orange Data OBDII diagnostic connector. Black 6-pin Driver Door Trigger Green/Violet 9 Open to N.C BCM/SJB in driver kick panel. Black 6-pin Trunk/Hatch Release Brown Negative BCM/SJB in driver kick panel. Black 6-pin Parking Lights Yellow/Blue 6 Positive BCM/SJB under driver dash. Gray 0-pin Power Liftgate Gray/Yellow 6 Negative Power liftgate switch. Black 6-pin Lock Blue/Green 6 Negative BCM/SJB in driver kick panel. Black 6-pin Unlock Yellow/Violet 8 Negative BCM/SJB in driver kick panel. Black 6-pin Ignition White/Orange Positive Ignition switch Black 7-pin Headlight Switch Ground N/A N/A N/A N/A N/A N/A Parking Light Yellow/Blue 6 Positive BCM/SJB under driver dash. Gray 0-pin RX Violet/Gray Data P.A.T.S. connector at ignition switch. Black -pin TX Yellow/Orange Data P.A.T.S. connector at ignition switch. Black -pin (+)V Green/Red Positive Ignition switch Black 7-pin BCM C80C 6 pin Connector BCM/SJB Gray 6 pin P.A.T.S. - pin (at ignition switch) Ignition Switch Black 7 pin BCM Gray 0 pin Connector OBDII Diagnostic Connector

13 Module Programming Page Refer to the LED Diagnostics section on page 7 for more information and for troubleshooting purposes. Important Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step. Warning! To take advantage of advanced features, you must use XpressVIP.5 (and higher) or the Directechs Mobile app. Flashing a module using your computer:. Connect the interface module to your computer using the XKLoader.. Go to using Internet Explorer, and select the Flash Module button.. Follow the instructions to select your vehicle, installation type, and configure your options.. Once you have configured the firmware options, click on the FLASH button. Flashing a module using your smartphone or tablet. Connect the interface module to your XKLoader.. Launch the Directechs Mobile app on your smartphone or tablet.. Select FLASH YOUR MODULE and follow the on screen instructions. When the flashing operation is successful, you can proceed with the programming instructions below. DD Installation If required for your installation, connect the 0-pin, -pin and -pin harnesses to the module, then connect the -pin DD harness. th st DD 0-pin rd nd -pin -pin OR WW Installation If required for your installation, connect the 0-pin and -pin harnesses to the module, then connect the -pin harness to the module. st DD 0-pin rd nd -pin -pin Wait until the LED turns ON solid red. Solid Go to the next page to complete the module programming.

14 Module Programming - Keys Required Page st Key IN Insert the first key, turn the key to the IGN position, the LED flashes green. Wait at least seconds, but START & no more than 0 seconds, then remove it. OFF IGN st Key OUT OFF IGN START within 5 seconds: Insert the second key and turn it to the IGN position: nd Key IN the LED flashes orange. START & Wait at least seconds but no more than 0 seconds, then remove the key. OFF IGN nd Key OUT OFF IGN START within 5 seconds: Wait at least seconds but no more than 0 seconds, then remove the key. nd Key OUT OFF IGN START or Turn the key to the IGN position again. Press and HOLD the programming button. nd Key IN The LED turns ON solid green for seconds, then turns OFF once the module has been successfully programmed. Then the vehicle door lock will cycle. OFF IGN START Press and HOLD the programming button. Press Solid & Off The vehicle ignition will be triggered. Release the Program button as soon as the Orange LED goes out. If you wait too long to release the programming button, you will have to start the programming over. The LED turns ON solid green for seconds, then turns OFF once the module has been successfully programmed. Solid & Off You have successfully completed the module programming sequence.

15 Module Reset Page 5 A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected. OR DD Installation If required for your installation, connect the 0-pin, -pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin DD harness. WW Installation If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. th 5 st st DD 0-pin DD 0-pin rd nd th nd th rd -pin -pin -pin -pin Wait seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red. & & Solid Release Solid Hard Reset Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and DD options) may have to be reconfigured. See the Feature & Option List section of this guide. OR DD Installation If required for your installation, connect the 0-pin, -pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin DD harness. WW Installation If required for your installation, connect the 0-pin & -pin harnesses to the module. Press and hold the programming button, then connect the -pin harness to the module. th 5 st st DD 0-pin DD 0-pin rd nd th nd th rd -pin -pin -pin -pin Wait seconds until the LED turns ON solid orange, and wait 0 more seconds until the LED starts to flash orange and red. Solid & Release the programming button. The LED turns ON solid red. Release & Solid

16 Feature & Option List Page 6 It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on The web offers more options; however, manual configuration of the features is possible using the information on this page. * Default Option Feat. Operation /Options Description RFTD Output Type. No RF Output* Module is connected to a remote starter using a standard installation.. RFTD Output Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).. Disabled. Safelock The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter. Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown. Smart OEM Alarm Control. Enabled* Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user. Transponder Ignition Disarm with Unlock:. Disabled (no Factory Alarm) No disarm operation on unlock or trunk. Enabled* Will disarm vehicle by cycling the ignition before unlocking or opening Trunk

17 Feature Programming To enter feature programming routine - Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after seconds). Release the Programming button. - The LED will flash green once slowly to indicate the feature number is. After a short delay, the LED flashes red rapidly to indicate the current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered. Accessing another feature - Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered. When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option. Once a feature is programmed - Other features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. OR - Press and HOLD the programming button for seconds. After seconds, the LED will turn ON orange for seconds to confirm the end of the programming sequence. Page 7

18 LED Diagnostics & Troubleshooting Page 8 LED Description Troubleshooting Module Programming Off Module has no power. Make sure the -pin DD harness is connected or that the -Volt is present between the red and black wires. If the -Volt is present, the module may be defective. Solid red Waiting for the completion of a programming sequence. This can also mean there is an issue with the data bus wiring. Make sure that the connections to the data bus are correct by referring to the installation section. Solid green x secs Module successfully programmed. Normal operation green orange slowly Solid orange x Module successfully detected the CAN circuit. Module successfully detected two () keys. Bypass skipped, module works in convenience mode only. Normal operation - Proceed to the next step in the programming sequence. Normal operation - Proceed to the next step in the programming sequence. Normal operation. Module Programming - Error Codes red x red x MS CAN not detected. Bypass data not detected. Check the Tan - Tan/Black wire connections. Wake up the data bus by turning the ignition on and try again. Some installation types do not need this connection. Skip by pressing the programming button 5 times. Check the bypass line connection. Make sure that RX and TX are not inverted. Start vehicle using the key to confirm the OEM equipment is still operational. red x 5 TX not detected. Yellow/Black wire did not detect the expected signal. red x 6 RX not detected. Orange/Black wire did not detect the expected signal. External Module Synchronization ( red, red, then orange) x 0 Active Ground While Running green red & orange green quickly DD & WW Commands OBDII feature not supported. GROUND OUT ON (GWR) command received. IGNITION ON command received. START ON command received. Diagnostic data bus not detected. Some features are not supported by SmartStart. This can be caused by missing wire connections or module hardware limitation. Refer to "Installation" on page 8 to check the connections. Otherwise, the Ground While Running (status) signal was lost or was never received by the module. Commands can come from RF, DD or WW. Otherwise, the ignition signal was not received by the module. In a WW install, it will show only if the ignition input wire is used. Otherwise, the start signal was not received by the module. In a WW install, it will show only if the ignition input wire is used. orange x Lock command has been received orange x Unlock command has been received If the bypass module fails to flash, it means the module did not receive the signal. Commands can come from RF, DD or WW. orange x Trunk command has been received

19 Limited One Year Consumer Warranty Page 9 For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Pending:,9,06. Made in Canada.

20 Quick Reference Guide DBALL/DBALL-FORD6 List of Available Commands Notes Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information. Button(s) Actions Press & hold for second to lock. Press & hold for second to unlock. Press & hold for second to remote start. Press & hold for 5 seconds to activate the trunk release (optional). x + x + x + Press once, then to activate the rear hatch/tail glass release (optional).* Press times, then to activate the panic mode. Press once, then to reset the remote starter runtime. * This output is configurable. see your authorized installation center for more information.