Minimum Breaking Force of Wire Rope (for Winches) 6 x 19 Classification / Bright (Uncoated), IWRC

Transcription

1 Minimum Breaking Force of Wire Rope (for Winches) 6 x 19 Classification / Bright (Uncoated), IWRC Wire rope Selection Rope Size (in) Approximate Weight (lb / ft) Minimum Breaking Force Extra Improved Plow Steel** (Tons) Recommended Safe Working Load* (lbs 5.0:1) , , , , , , , , , , , , , ,600 ** Minimum breaking forces listed above apply to ropes with bright or drawn galvanized wires. Minimum breaking forces are 10% lower for ropes with wires galvanized at finish size. *Regarding wire rope, ANSI B0.7, requires a minimum of 5:1 design factor with an 18:1 rope pitch diameter to drum is required for lifting and lowering applications. NOTE: Information provided on this page is credited by WIRE ROPE TECHNICAL BOARD 6 x19 IWRC 72 Lifting Gear Hire Corporation

2 Air Winch Selection Guide 0-22,000 lbs. (150-10,000 kg) Capacity How IR air winches are rated 2. How fast is the load to be moved e. Clutches: In the U.S.A., clutches are (if at all)? permitted on lifting winches. Although we don t usually recommend them, for certain. How much wire rope is needed? lifting applications they make sense. In Contact your Lifting Gear Hire representative to Europe, clutches are not allowed on lifting help you answer these questions and guide you winches. The Liftstar series is for lifting and through the selection process. the Pullstar for pulling. They are the same winches, but with different ratings and Lifting applications are generally defined as the Pullstar winches have clutches. those that require the brake to be engaged to prevent the load from falling. Refer to the quick Pulling applications: selection guide earlier in this section. Because of the.5:1 design criteria and the first layer rating, the ratings for pulling a. Choose a winch with a lifting capacity equal applications are higher for the same winch. to or greater than your application load. Choose a winch based on capacity, speed Winch capacity: Winches can lift or pull the highest loads at the first layer, and can lift/pull the least Tip: Consider using a pulley to increase capacity, reduce speed, and for better load control. and distance to be pulled. Manual band brakes and clutches are popular configurations, but each application has its own specific requirements. Again, consider pulleys to increase pulling capacity. at the top layer. This is due to the torque arm effect of the rope spooling on the winch drum. The closer the load is to the drum, the easier it is for the winch to turn and move the load. The further away the load is from the drum, the harder it is for the winch to turn. b. Make sure the average speed meets your criteria for cycle time. c. Wire rope selection is based on a 5:1 design factor and an 18:1 D/d ratio. The 18:1 D/d ratio is an ANSI / ASME B0-7 Air supply and consumption: All IR winches are rated at 90 psig (6. kg/m2) inlet pressure when the winch is running. The volume of air required is expressed in cubic feet per minute (cfm) or cubic meters per minute (m/min). Refer to the charts for air consumption data Winch speed: Winches generally move the load fastest at the top layer and slowest at the first layer. Think of your old record player. If you put a penny near the center of the record, it would simply spin at the same rate as the record. But if you put it near the outside edge, it would fly off. This is because the outer diameter of the record is travelling faster than the inner diameter. The same is true for a winch drum, and consequently the wire rope. Follow these guidelines to choose the correct utility winch for your application: First, consider these three fundamental questions: 1. How much is to be lifted, pulled, or tensioned? recommendation and is calculated as D + d / d where D = winch barrel diameter and d = wire rope size. The higher the ratio, the longer the wire rope life. As a guideline, this ratio should never go below 15:1. The use of 6 x 7 rope will increase flexibility. Tip: Winches with lower gear ratios overhaul better; that is, the load will run them backwards in a controlled descent with the throttle off. By applying the manual band brake, exceptional spotting can be achieved. Auto brakes are always recommended with remote control operation. d. Either manual or automatic brakes are suitable, although automatic brakes are recommended for lifting applications. for specific models. Compressor output must equal air consumption for continuous operation. Intermittent operation and/ or air storage facilities will allow the use of smaller compressors. Hoses and fittings should be sized equal to or preferably one size larger than the winch inlet. Strainers, lubricators, drum guards, filters and regulators are recommended based on air quality and the application. Mufflers and kits for piping away the exhaust are always suggested for operator safety and comfort. Pulling Lifting Gear Hire Corporation

3 Air Winch Selection Guide 0-22,000 lbs. (150-10,000 kg) Capacity Lifting: ANSI/ASME B0.16 Allowable Rated Line Pulls (5:1 Design Factor) First Layer Mid Layer Top Layer Average Flow Model Capacity Speed Capacity Speed Capacity Speed Required lbs. kg fpm m/m lbs. kg fpm m/m lbs. kg fpm m/m cfm m /m LS150R LS00R BU7A 1, , , LS600R 1, , , EU, EUL 2, , , LS1500R (1) 4,000 1, ,600 1, ,00 1, FA2B 5,000 2, ,000 1, ,200 1, FA2.5A 5,000 2, ,000 2, ,100 1, HU40A 5,000 2, ,000 1, ,200 1, LS2000R 6,200 2, ,150 2, ,400 2, FA2 6,600, ,200 2, ,400 2, FA2.5 7,000, ,800 2, ,000 2, FA5A 11,400 5, ,000 4, ,000, FA5T 12,500 5, ,00 5, ,400, FA5 12,500 5, ,500 5, ,000 5, LS5000R 15,600 7, ,900 5, ,000 5, FA7T 18,880 8, ,700 7, ,600 5, FA7 18,800 8, ,800 8, ,400 7, FA10 27,200 12, ,100 12, ,000 10, Pulling: ANSI/ASME B0.7 Allowable Rated Line Pulls (.5:1 Design Factor) Model First Layer Mid Layer Top Layer Average Flow Capacity Speed Capacity Speed Capacity Speed Required lbs. kg fpm m/m lbs. kg fpm m/m lbs. kg fpm m/m cfm m /m BU7A 1, , , PS1000R 2,200 1, , , EU, EUL,000 1, ,600 1, , FA2B 5,100 2, ,000 1, ,200 1, PS2400R (1) 5,280 2, ,800 2, ,70 1, FA2 6,800, ,400 2, ,500 2, FA2.5A 7,100, ,400 2, ,400 2, FA2.5 8,000, ,600, ,00 2, HU40A 5,100 2, ,000 1, ,200 1, PS4000R 8,800 4, ,00, ,200 2, FA5A 1,100 5,955 26/8 8 10,000 4, ,000, FA5T 18,000 8, ,600 5, ,600, FA5 18,000 8, ,100 6, ,600 5, PS10000R 22,000 10, ,00 8, ,600 7, FA7T 27,000 12, ,100 8, ,600 6, FA7 27,000 12, ,100 8, ,600 6, FA10 4,000 15, ,100 12, ,000 10, (1) Standard cable is overwound; LS1500R and PS2400R are underwound. It is the user s responsibility to determine the suitability of these winches for any particular use and to check for compliance with applicablle regulations 74 Lifting Gear Hire Corporation

4 Air Winch 1,000-22,000 lbs. Air Winch Specifications Nominal Capacity (lbs.) Model Line Speed (fpm) 1,000 BU7A ,000 EU, EUL ,500 HU, HUL ,000 H5U, H5UL Recommended Rope Size () 15:1 18:1 Specifications Drum Root Diam. () Motor HP Av. CFM Required Pipe Inlet Size Hose Size 4 Rope Anchor Hole Diam. () Max Stall Pull (lbs.) Net Weight (lbs.) 8 2, ,500 60, ,00 LS1500R 2 10mm 10mm ,000 HU40, HUL N/A ,400 FA ,000 K5U, K5UL ,000 FA , , , mm 7, , , , , ,000 1,061 8,000 FA5T ,000 2,065 10,000 K6U, K6UL ,000 1,14 1, FA ,000 2,000 12,600 FA7T ,400 FA ,000 2, ,000 1,977 22,000 FA ,000 2,800 Pulling Lifting Gear Hire Corporation

5 1,000-10,000 lbs. Classic I-R Air Winch Series Specifications Model Line Pull (lbs.) Line Speed fpm Classic Air Winch Specifications Drum Length () Motor HP SCFM Max. Stall First 90 PSI (lbs) Pipe Inlet Size (in) BU7A 1, Hose Size (in) Net Weight (lbs.) 4 75 HU 2, , HUL 2, , H5U, , H5UL, , HU40 4, , HUL40 4, , K5U 5, , K5UL 5, , K6U 10, , ,14 K6UL 10, , ,550 Performance is based on 90 psi air inlet pressure. Model Capacity (lbs.) Classic Series Drum Wire Rope Storage Capacities 1/4 ft. 5/16 ft. Max. Length on Winch (tightly wound)* /8 ft. 7/16 ft. Rope Anchor Hole Diameter () BU7A 1, /8 HU 2, /16 HUL 2,500 1,445 1, H5U, H5UL,000 1,445 1, HU40 4, /16 HUL40 4,000 1,445 1, K5U 5, /16 K5UL 5,000 1,741 1, K6U 10, K6UL 10,000 1,46 1, *Recommended drum working storage capacity is 80% of values shown. 1/2 ft. 5/8 ft. /4 ft. 7/8 ft. 76 Lifting Gear Hire Corporation

6 1,000-10,000 lbs. Classic I-R Air Winch Series Drawings HU40 K5U Series K5U - K5UL Series K6U - K6UL Model A Dimensions B C D Air Inlet Pipe Tap E Exhaust Pipe tap HU NPT NPT HUL NPT NPT H5U NPT NPT* H5UL NPT NPT* HU NPT NPT HUL NPT NPT *Remote control units 1 1/4 NPT. Note: Dimensions are subject to change. Please contact factory for certified prints. Model A Dimensions B C D E K6U K6UL Note: Dimensions are subject to change. Please contact factory for certified prints. Pulling Lifting Gear Hire Corporation

7 FA2.5A / FA5A (Third Generation): 5,000 to 10,000 lb (2,27 to 4,545 kg) capacity Model Dimensions Drum with Disc Brake Only with Manual Drum Brake Only with Manual and Disc Brake Length A B C D B C D B C D mm mm mm mm mm mm mm mm mm mm FA2.5A-S , FA2.5A-M , , , FA2.5A-L , , , FA2.5A-R , , , FA5A-SX , , , FA5A-LX , , , Note: Drum lengths for the FA5A-SM = 12 (05 mm), and FA5A-LM = 24 (610 mm). FA2.5A in inches (mm) FA2.5A FA5A FA5A in inches (mm) Typical allowable wire rope takeoff angle: For FA2.5A Dimensions are subject to change. Consult factory for certified prints. Shaded areas represent allowable angle of rope takeoff with interference with winch structural supports. For FA5A Standard Configuration Open Front Configuration (Option H) Standard Configuration Open Front Configuration (Option H) 78 Lifting Gear Hire Corporation

8 FA2.5A / FA5A (Third Generation): 5,000 to 10,000 lb (2,27 to 4,545 kg) capacity The Third Generation Force 5 Series is designed for world-wide standards, meeting or exceeding North American ANSI / ASME B0.7 winch standards, CE requirements for Europe and third party type Approval. The third Generation offers standard features with reduced maintenance for safety, durability, reliability, enhanced control, and superior performance. FA5A-LXK1 Standard Features: Automatic disc brake or manual band brake Corrosion resistant, marine duty Blue fasteners New self-cleaning K5C2 control valve improves flow and performance, has more stainless steel and polymer corrosion resistant parts, and is totally interchangeable with previous designs. 100% natural gas / sour gas compatible. Easy to install wedge type self-tightening rope anchor Powerful 5 piston air motor Safety is built In: Meets ASME B0.7 safety standards Lift and shift throttle lever prevents accidental throttle movement Throttle lever returns to OFF position and locks when released Disc brake is fully automatic and self-adjusting Wedge type, self tightening-rope anchor provides 80% of rope breaking strength Reliability: Maximum external corrosion protection against marine and other environments is provided as standard. Automatic oil bath disc brake has high thermal duty. Suitable for demanding applications. Marine grade alloys and stainless steel components make the valve Chest corrosion resistant and maintenance free. Performance: Superior load spotting control Positive braking action with automatic disc brake Specifications * Model FA2.5A FA5A Rated Mid Layer Line Pull, 5:1 DF 5,000 lbs. 2,27 kg 10,000 lbs. 4,545 kg Construction: Designed to meet the space and performance requirements of Classic winches Options: Corrosion resistant marine grade coating system: Sandblast to white metal finish and carbozinc primer with Marine 812 finish Band brakes manual and automatic Remote controls Construction cages Open frame configurations Foot print base with K6U and K6UL bolt pattern for FA5A Free spool clutch Tensioning manifold Drum guard Under wound configuration CE package Rope Diameter Wire Rope Storage Capacity S 7 (178) Length of Drum (mm) M 1 1/2 (4) L 20 (508) R 24 (610) mm ft. m ft. m ft. m ft. m FA2.5A Full Drum Storage , , , Rated Mid Layer Line Speed 114 fpm 5 m/m 2 fpm 10 m/m Top (6th) Layer Line Pull, 5:1 DF 4,100 lbs. 1,860 kg 8,000 lbs.,629 kg Top (6th) Layer Line Speed 141 fpm 4 m/m 4 fpm 1 m/m Max. Stall at First Layer 10,400 lbs. 4,727 kg 17,000 lbs. 7,727 kg Drum Root Diameter mm mm Motor Horsepower 25 hp 25 hp Avg. Air Consumption 700 scfm 20 m /min 700 scfm 20 m /min Air Inlet, NPT Size mm mm Recommended Rope Diameter mm 4 19 mm Weight 818 lbs. 72 kg 1,251 lbs. 569 kg *Performance is based on 90 psi (6. bar) air inlet pressure with the motor running , , , , Short Drum Long Drum 12 (05) (1) 15 (81) (2) 24 (610) (1) 27 (686) (2) FA5A Full Drum Storage , , , ,55 41 (1) With band brake. (2) Without band brake. Recommended drum working capacity is 80% of values shown. Pulling Lifting Gear Hire Corporation

9 Force 5 4,400-22,000 lbs. (2,000 to 10,000 kg) capacity Model Utility Rating 5:1 Top Layer Line Pull Specifications Performance Based on 90 psi (6. bar) Air Inlet Pressure with Motor Running Design Factor Top Layer Line Speed Drum Length A Avg. Air Consumption at rated psi (6. bar) Maximum Stall Pull 1st Layer Pipe Inlet Size Hose Size Ship Weight lbs. kg fpm m/m mm hp scfm m /m lbs. kg mm mm lbs. kg FA2-24 4,400 2, ,000 4, FA ,000 2, ,000 4, , FA ,000 5, ,000 10, , FA5T-24 8,400, ,000 10, , FA ,400 7, ,000 16, ,205 1,000 FA7T-24 12,600 5, ,000 16, ,5 1,059 FA7TGL-42,400 1, , ,000 4, ,981 1,52 FA7TPL-42 10,200 4, , ,000 16, ,850 1,29 FA ,000 10, ,000 17, ,200 1,451 Model Capacity recommended Wire Rope Size Drum Length Drum Wire Storage Capacities Rope Diameter 1 2 (1mm) 5 8 (16mm) 4 (19mm) 7 8 (22mm) 1 (25mm) (29mm) lbs. kg mm mm ft. m ft. m ft. m ft. m ft. m ft. m FA2 4,400 2, , FA2.5 5,000 2, , FA5 11,000 5, , , , ,41 4 1, , , FA5T 8,400, , , , , ,887 1,185 2, , , FA7 15,400 7, , , , , , , , , FA7T 12,600 5, ,58 1,02 2, , ,047 1,2 2, , , ,76 1,44,409 1,09 2, , , , , , , , , FA10 22,000 1, ,77 1,150 2, , , , ,201 1,280,19 1,011 2, , , ,271 1,606 4,168 1,270 2, , (1) Capacities meet ANSI-ASME B0.7 which requires 1/2 (1 mm) minimum clear flange above last layer. Capacities represent tightly wound wire rope. Recommended working capacity is 80% of values shown. 80 Lifting Gear Hire Corporation

10 4,400-22,000 lbs. Force 5 Air Winch Series Drawings FA5 FA10-24 Popeye with disc brake only in inches (mm) FA10-40 Popeye with disc brake only in inches (mm) Dimensions are subject to change. Consult factory for certified prints. Pulling Lifting Gear Hire Corporation

11 4,700 lbs. - TA2 Series Specifications Model TA2 (Shown with optional drum guard and automatic band brake) TA2 Series Performance Characteristics Model TA2-16 TA2-24 Load Rating 1st Layer 7,200 lbs. 7,200 lbs. Load Rating Mid-Drum 5,700 lbs. 5,700 lbs. Load Rating Full Drum 4,700 lbs. 4,700 lbs. Line Speed 1st Layer 0 fpm 0 fpm Line Speed Mid-Drum 8 fpm 8 fpm Line Speed Full Drum 46 fpm 46 fpm Drum Capacity 1st Layer 8 ft. 10 ft. Drum Capacity Mid-Drum 80 ft. 570 ft. Drum Capacity Full Drum 850 ft. 1,270 ft. Input HP 7.1 hp 7.1 hp Max. Stall Pull 1st Layer 9,000 lbs. 9,000 lbs. Wire Rope Diameter.5.5 Pressure 90 psi 90 psi Flow 250 scfm 250 scfm Pipe Inlet Size 1 1 Hose Size Approximate Ship Weight 990 lbs. 1,080 lbs TA2 Series Dimensions Item TA2-16MX1 TA2-24MX1 A C F H J K L W Y Y Z1 22º 22º Z2 4º 4º Bolt Hole Size Grade G G8 82 Lifting Gear Hire Corporation

12 5,000 lbs. - TA2.5 Series Specifications Model TA2.5 (Shown with optional drum guard and line guide) TA2.5 Series Performance Characteristics Model TA TA Load Rating 1st Layer 7,200 lbs. 7,200 lbs. Load Rating Mid-Drum 5,900 lbs. 5,900 lbs. Load Rating Full Drum 5,000 lbs. 5,000 lbs. Line Speed 1st Layer 79 fpm 79 fpm Line Speed Mid-Drum 96 fpm 96 fpm Line Speed Full Drum 114 fpm 114 fpm Drum Capacity 1st Layer 71 ft. 110 ft. Drum Capacity Mid-Drum 260 ft. 90 ft. Drum Capacity Full Drum 580 ft. 860 ft. Input HP 18. hp 18. hp Max. Stall Pull 1st Layer 11,000 lbs. 11,000 lbs. Wire Rope Diameter.6.6 Pressure 90 psi 90 psi Flow 600 scfm 600 scfm Pipe Inlet Size Hose Size Approximate Ship Weight 1,15 lbs. 1,400 lbs. TA2 Series Dimensions Item TA2.5-16MX1 TA2.5-24MX1 A C F H J K L W Y Y Z1 228º 228º Z2 27º 27º Bolt Hole Size Grade G G8 Dimensions are for reference only and subject to change without notice. Pulling Lifting Gear Hire Corporation

13 11,500 lbs. - TA5 Series Specifications Model TA5 (Shown with optional automatic band brake) TA5 Series Performance Characteristics Model TA5-16 TA5-24 TA5-0 Load Rating 1st Layer 18,000 lbs. 18,000 lbs. 18,000 lbs. Load Rating Mid-Drum 14,000 lbs. 14,000 lbs. 14,000 lbs. Load Rating Full Drum 11,500 lbs. 11,500 lbs. 11,500 lbs. Line Speed 1st Layer 0 fpm 0 fpm 0 fpm Line Speed Mid-Drum 9 fpm 9 fpm 9 fpm Line Speed Full Drum 47 fpm 47 fpm 47 fpm Drum Capacity 1st Layer 72 ft. 120 ft. 150 ft. Drum Capacity Mid-Drum 60 ft. 550 ft. 680 ft. Drum Capacity Full Drum 810 ft. 1,210 ft. 1,520 ft. Input HP 17.8 hp 17.8 hp 17.8 hp Max. Stall Pull 1st Layer,000 lbs.,000 lbs.,000 lbs. Wire Rope Diameter Pressure 90 psi 90 psi 90 psi Flow 550 scfm 550 scfm 550 scfm Pipe Inlet Size Hose Size Approximate Ship Weight 2,585 lbs. 2,745 lbs. 2,870 lbs. TA5 Series Dimensions Item TA5-16MX1 TA5-24MX1 TA5-0MX1 A C F H J K L W No. of Bolt Holes Y Y Z1 224º 224º 224º Z2 50º 50º 50º Bolt Hole Size Grade 4 - G8 4 - G8 4 - G8 84 Lifting Gear Hire Corporation

14 15,900 lbs. - TA7 Series Specifications Model TA7 (Shown with manual band brake) TA7 Series Performance Characteristics Model TA7-24 TA7-0 TA7-6 Load Rating 1st Layer 2,600 lbs. 2,600 lbs. 2,600 lbs. Load Rating Mid-Drum 19,000 lbs. 19,000 lbs. 19,000 lbs. Load Rating Full Drum 15,900 lbs. 15,900 lbs. 15,900 lbs. Line Speed 1st Layer 19 fpm 19 fpm 19 fpm Line Speed Mid-Drum 24 fpm 24 fpm 24 fpm Line Speed Full Drum 29 fpm 29 fpm 29 fpm Drum Capacity 1st Layer 120 ft. 160 ft. 190 ft. Drum Capacity Mid-Drum 520 ft. 650 ft. 780 ft. Drum Capacity Full Drum 1,150 ft. 1,440 ft. 1,70 ft. Input HP 14.4 hp 14.4 hp 14.4 hp Max. Stall Pull 1st Layer 8,000 lbs. 8,000 lbs. 8,000 lbs. Wire Rope Diameter Pressure 90 psi 90 psi 90 psi Flow 550 scfm 550 scfm 550 scfm Pipe Inlet Size Hose Size Approximate Ship Weight,600 lbs.,765 lbs.,965 lbs. TA7 Series Dimensions Item TA7-24MX1 TA7-0MX1 TA7-6MX1 A C F H J K L W Y Y Z1 210º 210º 210º Z2 9º 9º 9º Bolt Hole Size Grade G G G8 Pulling Lifting Gear Hire Corporation

15 1,100 lbs. Model Configuration/Performance/Dimension 1,100 lbs. Model Air Pressure psi (MPa) Motor Power hp (kw) Specifications (at Half Drum) Rope Pull 1 b (kn) Rope Speed fpm (m/min) Air Consumption cfm (Nm / min) Rope Capacity 0 in x ft (m) Weight lbs. (kg) 90 (0.62) 2. (1.7) 1,100 (5) 62 (19) 71 (2.0) 5 16 x 145 (45) About 97 (44) Note: Dimensions are inches, ( ) metric mm. 86 Lifting Gear Hire Corporation

16 4,400 lbs. Model Configuration/Performance/Dimension San-Ei 4,400 lbs. Model Air Winch 4,400 lbs Model Configuration / Performance / Dimension DRUM SIZE ROPE HOLE Ø O.6 (Ø 16) 0.59 (15) Ø 7.09 (Ø180) Ø (Ø 410) 2.87 (7) CONTROL LEVER 1.2 (6) (60.5) (56) 2.8 (72) ROPE PULL STOP ROPE PAY OUT OIL PLUG 1.46 (7) ROPE ENTRY CLUTCH LEVER DRUM CENTER 4-Ø 1.02 (Ø 26) (05) 6.16 (156.5) AIR INLET Rc1 EXHAUST Rc1-1/2 BRAKE LEVER TOP LAYER 7.80 (198) OIL GAUGE DRAIN PLUG 1.57 (40) (617) 1.18 (0) 2.64 (67) (81) 0.9 (772) (454) (100) 2.64 (67) 1.0 (1) (576) 1.18 (0) 2.95 (75) (400) (470) 9.72 (247) 9.25 (25) (482) 2.95 (75) 122 SPECIFICATIONS (at HALF DRUM) AIR PRESSURE psi (MPa) MOTOR POWER hp (kw) ROPE PULL 1b (kn) 90 (0.62) 9.6 (7.15) 4400 (20) 62 (19) 191 (5.4) Air Pressure psi (MPa) ROPE SPEED fpm (m/min) AIR CONSUMPTION cfm (Nm /min) Motor Power hp (kw) 1/2 x 750 (20) Specifications (287) (at Half Drum) Rope Pull 1 b (kn) Rope Speed fpm (m/min) Air Consumption cfm (Nm / min) Rope Capacity 0 in x ft (m) Weight lbs. (kg) 90 (0.62) 9.6 (7.15) 4,400 (20) 62 (19) 191 (5.4) 1 2 x 750 (20) About 61 (287) Note: Dimensions are inches, ( ) metric mm. ROPE CAPACITY Ø in x ft (m) WEIGHT lb (kg) ABOUT 61 NOTE: DIMENSIONS ARE INCHES, BRACKETS ( ) METRIC mm Lifting Gear Hire Corporation Pulling Lifting Gear Hire Corporation

17 6,600 lbs. Model Configuration/Performance/Dimension 6,600 lbs. Model Air Pressure psi (MPa) Motor Power hp (kw) Specifications (at Half Drum) Rope Pull 1 b (kn) Rope Speed fpm (m/min) Air Consumption cfm (Nm / min) Rope Capacity 0 in x ft (m) Weight lbs. (kg) 90 (0.62) 16 (12) 6,600 (0) 62 (19) 18 (9.0) 5 8 x 1,050 (20) About 1,129 (51) Note: Dimensions are inches, ( ) metric mm. 88 Lifting Gear Hire Corporation

18 11,000 lbs. Model Configuration/Performance/Dimension 11,000 lbs. Model Air Pressure psi (MPa) Motor Power hp (kw) Specifications (at Half Drum) Rope Pull 1 b (Kn) Rope Speed fpm (m/min) Air Consumption cfm (N-M / min) Rope Capacity 0 in x ft (m) Weight lbs. (kg) 90 (0.62) 16 (12) 11,000 (50) 6 (11) 18 (9.0) 7 8 x 750 (20) About 1,921 (87) Note: Dimensions are inches, ( ) metric mm. Pulling Lifting Gear Hire Corporation

19 800 1,500 lbs. U-8 Series Specifications U-8 Series Model TM Line Pull 1st Layer Line Speed 1st Layer Specifications Power Required Cable Capacity (Ft.) /16 1/4 5/16 /8 U-8A-15 1, fpm psi Weight (lbs.) 90 Lifting Gear Hire Corporation

20 22,000 lbs AW Air Winch Specifications Dimensions Model B C D E 12 DIA DIA Note: Dimensions are subject to change. Please contact factory for certified prints. Layer No. Capacity (ft) Accumulated Capacity (ft) Pitch Dia (in) Specifications Line pull (lbs) Max Hp Speed (fpm) Flange Clearance Stall Line Pull (lbs) Start Line Pull (lbs) , ,20 44, , ,676 40, , ,79 7, , ,60 4, FPM AT F.S , ,428 2, , ,859 0, , ,590 28, , ,572 27, , ,764 25, , ,16 24, , ,662 2, Pulling Lifting Gear Hire Corporation

21 Double Drum Air Winch TA2 16 Drums - 4,700 lbs. TA2 Series Winch TA2 Series Performance Characteristics Winch Model Load Rating - 1st Layer Load Rating - Mid Drum Load Rating - Full Drum Line Speed - 1st Layer Line Speed - Mid Drum Line Speed - Full Drum Dum Capacity - 1st Layer Drump Capacity - Mid Drum Drum Capacity - Full Drum Input HP Max. Stall Pull - 1st Layer Wire Rope Diameter Pressure Flow Pipe Inlet Size Hose Size Approximate Ship Weight TA2-16MX1 7,200 lbs. 5,700 lbs. 4,700 lbs. 0 fpm. 8 fpm. 46 fpm. 8 ft. 80 ft. 850 ft. 7.1 hp. 9,000 lbs psi. 250 scfm lbs. TA2 Series Dimensions TA2 Series Dimensions Item A C J K L W TA2-16MX Z1 2 Z2 4 Bolt Hole Size Grade OPERATORS SAFETY CAGE AND SEAT BASE 9-0 5/8 - G8 Specification Drawings to match the information in this table can be found on page 82 of this catalog MOUNTING OPTION 1 THERN TA2-16 SERIES WINCH Measurements in this diagram reflect the dimensions of the winch frame ONLY. Refer to the dimension table for more information. 92 Lifting Gear Hire Corporation

22 Double Drum Air Winch TA5 24 Drums - 11,500 lbs. TA5 Series Winch TA5 Series Performance Characteristics Winch Model TA5-24 Load Rating - 1st Layer 18,000 lbs. Load Rating - Mid Drum 14,000 lbs. Load Rating - Full Drum 11,500 lbs. Line Speed - 1st Layer 0 fpm. Line Speed - Mid Drum 9 fpm. Line Speed - Full Drum 47 fpm. Dum Capacity - 1st Layer 120 ft. Drump Capacity - Mid Drum 550 ft. Drum Capacity - Full Drum 1,210 ft. Input HP 17.8 hp. Max. Stall Pull - 1st Layer,000 lbs. Wire Rope Diameter.75 Pressure 90 psi. Flow 550 scfm. Pipe Inlet Size 1.5 Hose Size 1.5 Approximate Ship Weight 2,745 lbs. TA5 Series Dimensions TA5 Series Dimensions Item A C J K L W TA Z1 224 Z2 50 Bolt Hole Size Grade /4 in - G8 Specification Drawings to match the information in this table can be found on page 84 of this catalog Measurements in this diagram reflect the dimensions of the winch frame ONLY. Refer to the dimension table for more information Pulling Lifting Gear Hire Corporation

23 Double Drum Air Winch TA7 0 Drums - 15,900 lbs. TA7 Series Winch TA7 Series Performance Characteristics in TA7-0MX1 Load Rating - 1st Layer 2,600 lbs. Load Rating - Mid Drum 19,000 lbs. Load Rating - Full Drum 15,900 lbs. Line Speed - 1st Layer 19 fpm. Line Speed - Mid Drum 24 fpm. Line Speed - Full Drum 29 fpm. Dum Capacity - 1st Layer 160 ft. Drump Capacity - Mid Drum 650 ft. Drum Capacity - Full Drum 1,440 ft. Input HP 14.4 hp. Max. Stall Pull - 1st Layer 8,000 lbs. Wire Rope Diameter.88 Pressure 90 psi. Flow 550 scfm. Pipe Inlet Size 1.5 Hose Size 1.5 Approximate Ship Weight,765 lbs. TA7 Series Dimensions TA7 Series Dimensions Item A C J K L W TA7-0MX Z1 210 Z2 9 Bolt Hole Size Grade 7/8 - G8 Specification Drawings to match the information in this table can be found on page 85 of this catalog Measurements in this diagram reflect the dimensions of the winch frame ONLY. Refer to the dimension table for more information Lifting Gear Hire Corporation