E3Z-LT/LR/LL. Compact and Reliable Laser Photoelectric Sensor. Compact Laser Photoelectric Sensor with Built-in Amplifier.

Transcription

1 Compact Laser Photoelectric Sensor with Built-in Amplifier EZ-LT/LR/LL Compact and Reliable Laser Photoelectric Sensor Safety and reliability with laser class (JIS and IEC). Product lineup includes models with distance setting without influence of color. Maximum ambient operating temperature of 55 C and water-proof construction in EZ class. CSM_EZ-LT_LR_LL_DS_E_6_ Be sure to read Safety Precautions on page 9. Applications Detect the sides of large tiles. Count bottles. Greatly Enhanced Beam Visibility for Easier Optical Axis Adjustment of Sensors Detect chip components on tape. Reliable Detection of Small Objects and Narrow Gaps with the Small Spot Detect protruding straws. Long-distance Sensing at mm ( Paper) A Low / Error for Applications with Mixed Colors

2 Ordering Information Sensors (Refer to Dimensions on page.) Sensing method Appearance Connection method Through-beam (Emitter + Receiver) * Retro-reflective with MSR function Distance-settable () Pre-wired ( m)* Connector (M8, pins) Pre-wired ( m)* Response time ms Sensing distance * Connector (Using E9-R) (M8, pins) (Using E9-R6) Pre-wired ( m)* Connector (M8, pins) Pre-wired ( m)* Connector (M8, pins).5 ms (Using E9-R) to mm (Min. distance set) to mm (Max. distance set) 5 to mm (Min. distance set) 5 to mm (Max. distance set) 6 m * 5 m ( mm) 7 m ( mm) 7 m ( mm) EZ-LT/LR/LL Red light Model NPN output PNP output EZ-LT6 M EZ-LT8 M Emitter EZ-T6-L M Emitter EZ-T8-L M Receiver EZ-T6-D M Receiver EZ-T8-D M EZ-LT66 EZ-LT86 Emitter EZ-T66-L Emitter EZ-T86-L Receiver EZ-T66-D Receiver EZ-T86-D EZ-LR6 M EZ-LR8 M EZ-LR66 EZ-LR86 EZ-LL6 M EZ-LL8 M EZ-LL66 EZ-LL86 EZ-LL6 M EZ-LL8 M EZ-LL68 EZ-LL88 *. The Reflector is sold separately. Select the Reflector model most suited to the application. *. Values in parentheses indicate the minimum required distance between the Sensor and Reflector. *. Pre-wired Models with a.5-m cable are also available for these products. When ordering, specify the cable length by adding.5m to the end of the model number (e.g., EZ-LT6.5M). M Pre-wired Connector Models are also available. When ordering, add -MJ to the end of the model number (e.g., EZ-LT6-MJ). The cable is. m long. Also, the following connection forms can be manufactured. Ask your OMR representative for details. Pre-wired Models with -m or 5-m cables Pre-wired Connector Models with M8 -pin connectors or M8 -pin connectors. *. Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver. Orders for individual Emitters and Receivers are accepted. (Modifications are required for some models. Ask your OMR representative for details.) Accessories Slits (A Slit is not provided with a Through-beam Sensor. Order a Slit separately if required.) (Refer to Dimensions on page.) Slit width Sensing distance Minimum detectable object (typical) Reflectors (A Reflector is required for Retro-reflective Sensors: A Reflector is not provided with the Sensor. Be sure to order a Reflector.) (Refer to Dimensions on page.) Model.5 mm dia. m. mm dia. E9-S65A Name Sensing distance (typical) Model Remarks Contents One set (contains Slits for both the Emitter and Receiver) Reflector 5 m ( mm) E9-R Retro-reflective models are not provided with Reflectors. 7 m ( mm) E9-R Separate the Sensor and the Reflector by at least the distance given in parentheses. 7 m ( mm) E9-R6 The MSR function is enabled.

3 EZ-LT/LR/LL Mounting Brackets A Mounting Bracket is not provided with the Sensor. Order a Mounting Bracket separately if required. (Refer to Dimensions on E9-L/F9-L/E9-S/E9-R.) Model Quantity Remarks Appearance Appearance Model Quantity Remarks E9-L5 E9-L98 Metal Protective Cover Bracket * Mounting Brackets E9-L E9-L5 set (Sensor adjuster) E9-L Horizontal Mounting Bracket * Easily mounted to the aluminum frame rails of conveyors and easily adjusted. E9-L5 set For left to right adjustment E9-L Horizontal Protective Cover Bracket * E9-L Rear Mounting Bracket E9-L Compact Protective Cover Bracket (For EZ only) * Note: When using a Through-beam Sensor, order one Mounting Bracket for the Receiver and one for the Emitter * Cannot be used for Standard Connector models. Sensor I/O Connectors (Models for Connectors and Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) (Refer to Dimensions on XS, XS) M8 M (For -MJ models) Size Cable Appearance Cable type Model Standard Straight * L-shaped * * Straight * L-shaped * Note: When using a Through-beam Sensor, order one Mounting Bracket for the Receiver and one for the Emitter *. The connector will not rotate after connecting. *. The cable is fixed at an angle of 8 from the sensor emitter/receiver surface. m XSF-M--A 5 m XSF-M-5-A -wire m XSF-M--A 5 m XSF-M-5-A m XSF-D-DC-A 5 m -wire XSF-D-GC-A m XSF-D-DC-A 5 m XSF-D-GC-A

4 Ratings and Specifications EZ-LT/LR/LL Item Model Sensing distance Sensing method Through-beam Retro-reflective with MSR function Distance-settable (BGS models) Response Standard response High-speed response NPN output PNP output 6 m EZ-LT6/-LT66 EZ-LR6/-LR66 EZ-LL6/-LL66 EZ-LL6/-LL68 EZ-LT8/-LT86 EZ-LR8/-LR86 EZ-LL8/-LL86 EZ-LL8/-LL88. to 5 m (when using E9-R). to 7 m (when using E9-R). to 7 m (when using E9-R6) ( mm): to mm ( mm): to 6 mm Set distance range --- ( mm): to mm ( mm): to 6 mm Spot diameter (typical) 5-mm dia. at m.5-mm dia. at mm ( mm): 5 to mm ( mm): 5 to mm ( mm): to mm ( mm): to mm Standard sensing object Opaque: -mm dia. min. Opaque: 75-mm dia. min. --- Minimum detectable object (typical) 6-mm-dia. opaque object at m.-mm-dia. stainless-steel pin gauge at mm Differential travel --- 5% max. of set distance /white error --- 5% at 6 mm 5% at mm Directional angle Receiver: to Light source (wavelength) Red LD (655 nm), JIS CLass, IEC Class, FDA Class II Power supply voltage to VDC±%, ripple (p-p): % max. Current consumption 5 ma (Emitter 5 ma, Receiver ma) ma max. Control output Residual output voltage Output mode switching Protection circuits Load power supply voltage: 6. VDC max., Load current: ma max., Open collector output Load current of less than ma: V max. Load current of to ma: V max. Switch to change between light- and dark- Reversed power supply polarity protection, Output short-circuit protection, and Reversed output polarity protection Reversed power supply polarity protection, Output short-circuit protection, Mutual interference prevention, and Reversed output polarity protection Response time Operate or reset: ms max. Operate or reset:.5 ms max. Sensitivity adjustment One-turn adjuster Five-turn endless adjuster Ambient illumination (Receiver side) Ambient temperature range Ambient humidity range Insulation resistance Dielectric strength Vibration resistance Shock resistance Incandescent lamp:, lx max. Sunlight:, lx max. Operating: to 55 C, Storage: 5 to 7 C (with no icing or condensation) Operating: 5% to 85%, Storage: 5% to 95% (with no icing or condensation) MΩ min. at 5 VDC, VAC, 5/6 Hz for min Degree of protection IP67 (IEC 659) Connection method Indicator Weight (packed state) Material Accessories Destruction: to 55 Hz,.5-mm double amplitude for hours each in X, Y, and Z directions Destruction: 5 m/s times each in X, Y, and Z directions Pre-wired cable (standard length: m): Standard M8 Connector: EZ-L@@/-L@@ EZ-L@@6/-L@@8 Stability (green) Emitter for Through-bream Models has power only. Pre-wired cable ( m) Approx. g Approx. 65 g Standard Connector Approx. g Approx. g Case PBT (polybutylene terephthalate) Lens Modified polyarylate resin Methacrylic resin Modified polyarylate resin Instruction manual (Neither Reflectors nor Mounting Brackets are provided with any of the above models.)

5 Engineering Data (Typical) EZ-LT/LR/LL Parallel Operating Range Through-beam Models Through-beam Models Retro-reflective Models + E9-S65A EZ-LR@@ Distance Y (mm) 5 5 Distance (mm) 5 5 Distance Y (mm) 6 E9-R E9-R6 X Y X Y 5 5 E9-R 5 Distance X (m) Distance (m) 6 Distance X (m) Operating range Y (mm) Operating Range at a Set Distance of mm EZ-LL@@ Excess Gain vs. Set Distance Through-beam Models EZ-LT@@ Excess gain ratio (multiple) Y X Sensing object: mm white Distance X (mm) Operating Range at a Set Distance of mm EZ-LL@@ Operating range Y (mm) Retro-reflective Models EZ-LR@@ Excess gain ratio (multiple) E9-R E9-R Y X Sensing object: mm white 5 6 Distance X (mm) E9-R Distance (m) Close Range Characteristics EZ-LL@/-LL@6 Sensing distance (mm) mm 6 mm. Distance (m) EZ-LL@/-LL@8 Sensing distance (mm) 5 mm 5 5 mm 5 mm mm 5 mm mm Setting: mm mm mm mm 9 mm Setting: 6 mm Setting: mm Setting: mm mm mm mm 9 mm Setting: Setting: Setting: Setting: mm mm mm mm 5

6 Hysteresis (%) Hysteresis (%) EZ-LT/LR/LL Sensing Distance vs. Sensing Object Material Paper with a Set Distance of mm Paper with a Set Distance of mm Sensing distance (mm) 5 Sensing distance (mm) 5 EZ-LL@/-LL@6 Paper with a Set Distance of mm Sensing distance (mm) Veneer Cardboard SUS rubber Mirror surface Material EZ-LL@/-LL@8 Paper with a Set Distance of mm Sensing distance (mm) 8 6 Veneer Cardboard SUS Mirror rubber surface Material Emission Spot Diameter vs. Distance Through-beam and Retro-reflective Models (Same for All Models) EZ-LT@@, EZ-LR@@ EZ-LL@@ Spot diameter (mm) a Spot shape Dimension a b Veneer Cardboard SUS rubber Mirror surface Material (Same for All Models) Spot diameter (mm) Dimension a Dimension b. a Dimension b. b Spot shape Veneer Cardboard SUS rubber Hysteresis vs. Distance EZ-LL@ (LL@6) Mirror surface Material 5 6 Set distance (m) EZ-LL@ (LL@8) 5 6 Set distance (mm) Set distance (mm) Inclination Characteristics (Vertical) EZ-LL@@ Sensing distance variation (%) 5 5 Distance setting: mm Sensing object: mm (Upwards 5 and Downwards) Inclination angle + θ 5 θ Sensing Center object line Inclination angle θ ( ). Set distance (mm) Inclination Characteristics (Horizontal) EZ-LL@@ Sensing distance variation (%) Distance setting: mm Sensing object: 5 mm 5 5 (Left and Right) Inclination angle + θ θ 5 Sensing Center object line Inclination angle θ ( ) 6

7 I/O Circuit Diagrams NPN Output Model EZ-LT6 * EZ-LT66 * EZ-LR6 EZ-LR66 EZ-LL6 EZ-LL66 EZ-LL6 EZ-LL68 PNP Output Model mode Light- Dark- Light- Dark- mode Timing charts Light incident Light interrupted Output transistor Load Operate (Between brown and black leads) Light incident Light interrupted Output transistor Load Operate (Between brown and black leads) Through-beam Emitter Power Photoelectric Sensor Main Circuit NEAR FAR Output transistor Load Operate (Between brown and black leads) NEAR FAR Output transistor Load Operate (Between brown and black leads) Timing charts selector L side (LIGHT ) D side (DARK ) L side (LIGHT ) D side (DARK ) selector to VDC Output circuit Through-beam Receivers, Retro-reflective Models (Orange) M Connector M Connector (Orange) Stability (Green) Photoelectric Sensor Main Circuit M8 -pin Connector Pin is not used. M8 -pin Connector M Connector Stability (Green) Photoelectric Sensor Main Circuit Pins and are not used. M8 -pin Connector Pin is not used. (Control output) EZ-LT/LR/LL ZD ma max. M8 -pin Connector M8 -pin Connector (Control output) ma max. ZD M8 -pin Connector Output circuit to VDC Load (Relay) V to VDC Load (Relay) V EZ-LT8 * EZ-LT86 * EZ-LR8 EZ-LR86 Light- Dark- Light incident Light interrupted Output transistor Load Operate (Between blue and black leads) D side (DARK ) M Connector Light incident Light interrupted Through-beam Receivers, Retro-reflective Models L side Stability Output transistor (LIGHT ) ZD Load Operate (Orange) (Green) Photo- (Between blue and black leads) (Control output) electric Sensor Main Circuit M8 -pin Connector Pin is not used. ma max. M8 -pin Connector to VDC Load (Relay) V Through-beam Emitter Power Photoelectric Sensor Main Circuit to VDC M Connector M8 -pin Connector Pins and are not used. M8 -pin Connector EZ-LL8 EZ-LL86 EZ-LL8 EZ-LL88 Light- Dark- NEAR FAR Output transistor Load Operate (Between blue and black leads) NEAR FAR Output transistor Load Operate (Between blue and black leads) L side (LIGHT ) D side (DARK ) Pin is not used. * Models numbers for Through-beam Sensors (EZ-LT@@) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: EZ-LT6-L M), the model number of the Receiver, by adding "-D" (example: EZ-LT6-D M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. (Orange) M Connector Stability (Green) Photoelectric Sensor Main Circuit M8 -pin Connector (Control output) ZD ma max. M8 -pin Connector to VDC Load (Relay) V 7

8 EZ-LT/LR/LL Plugs (Sensor I/O Connectors) M8 -pin Connectors Wire color M Connectors Pin No. XSF-M--A XSF-M-5-A XSF-D-DC-A XSF-D-GC-A XSF-M--A XSF-M-5-A XSF-D-DC-A XSF-D-GC-A Wire color Nomenclature Sensors with Sensitivity Adjustment and Mode Selector Switch Through-beam Models EZ-LT@@ (Receiver) Distance-settable Sensor EZ-LL@@ Retro-reflective Models EZ-LR@@ Stability (green) Distance adjuster (5-turn endless) selector Sensitivity adjuster Stability (green) Mode selector switch 8

9 Safety Precautions Refer to Warranty and Limitations of Liability. WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purpose. To ensure safe use of laser products, do not allow the laser beam to enter your eye. Direct exposure may adversely affect your eyesight. CAUTI Do not connect an AC power supply to the Sensor. If AC power ( VAC or more) is supplied to the Sensor, it may explode or burn. Precautions for Safe Use Be sure to abide by the following precautions for the safe operation of the Sensor. Operating Environment Do not use the Sensor in locations with explosive or flammable gas. Wiring Power Supply Voltage and Output Load Power Supply Voltage Make sure that the power supply to the Sensor is within the rated voltage range. If a voltage exceeding the rated voltage range is supplied to the Sensor, it may explode or burn. Power Supply Voltage The maximum power supply voltage is 6. VDC. Applying a voltage exceeding the rated range may damage the Sensor or cause burning. Load Do not use a load that exceeds the rated load. Load Short-circuiting Do not short-circuit the load, otherwise the Sensor may be damaged or it may burn. Connection without Load Do not connect the power supply to the Sensor with no load connected, otherwise the internal elements may explode or burn. Always connect a load when wiring. EZ-LT/LR/LL Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Laser Warning Labels Be sure that the correct laser warning label (enclosed) is attached for the country of intended use of the equipment containing the Photoelectric Sensor. Refer to the user's manual for details. Usage Environment Water Resistance The Sensor is rated IP67. Do not use it in water, in the rain, or outdoors. Ambient Environment Do not install the product in the following locations. Doing so may result in product failure or malfunction. Locations subject to excess dust and dirt Locations subject to direct sunlight Locations subject to corrosive gas Locations subject to organic solvents Locations subject to shock or vibration Locations subject to exposure to water, oil, or chemicals Locations subject to high humidity or condensation Designing Power Reset Time The Sensor is ready to operate ms after the Sensor is turned. If the load and Sensor are connected to independent power supplies respectively, be sure to turn the Sensor before supplying power to the load. Wiring Avoiding Malfunctions If using the Sensor with an inverter or servomotor, always ground the FG (frame ground) and G (ground) terminals, otherwise the Sensor may malfunction. Mounting Mounting the Sensor If Sensors are mounted face-to-face, make sure that the optical axes are not in opposition to each other. Otherwise, mutual interference may result. Always install the Sensor carefully so that the aperture angle range of the Sensor will not cause it to be directly exposed to intensive light, such as sunlight, fluorescent light, or incandescent light. Do not strike the Photoelectric Sensor with a hammer or any other tool during the installation of the Sensor, or the Sensor will lose its water-resistive properties. Use M screws to mount the Sensor. When mounting the case, make sure that the tightening torque applied to each screw does not exceed.5 N m. Metal Connectors Always turn the power supply to the Sensor before connecting or disconnecting the metal connector. Hold the connector cover to connect or disconnect it. If the XSF is used, always tighten the connector cover by hand. Do not use pliers. If the tightening is insufficient, the degree of protection will not be maintained and the Sensor may become loose due to vibration. The appropriate tightening torque is. to. N m. If other commercially available connectors are used, follow the recommended connector application conditions and recommended tightening torque specifications. 9

10 EZ-LT/LR/LL Mounting Direction for Distance-settable Models Make sure that the sensing side of the Sensor is parallel with the surface of the sensing objects. Normally, do not incline the Sensor towards the sensing object. Sensing side The stability may turn off in reaction to reflection from background objects. In such cases, incline the Sensor by as shown in the illustration for more stable detection. Background object, conveyor, etc. Reflection Approx. If the sensing object has a glossy surface, however, incline the Sensor by 5 to as shown in the illustration, provided that the Sensor is not influenced by background objects. Surface of sensing object Adjusting Distance-settable Models Indicator Unstable NEAR Stable NEAR NEAR region Distance threshold (settable) Unstable FAR Stable FAR FAR region Glossy object If there is a mirror-like object below the Sensor, the Sensor may not operate stably. Therefore, incline the Sensor or separate the Sensor from the mirror-like object as shown below. Sensing object Mirror-like object Do not install the Sensor in the wrong direction. Refer to the following illustration. BGS L/ D/ Stability (green) Stability (green) Note: If the stability is lit, the detection/no detection status is stable within the rated ambient operating temperature ( to 55 C). Inspection and Maintenance Cleaning Never use paint thinners or other organic solvents to clean the surface of the product. Correct Correct Incorrect Sensing object Moving direction Moving direction Sensing object Sensing object Moving direction Install the Sensor as shown in the following illustration if each sensing object greatly differs in color or material. Correct Incorrect Moving direction Moving direction

11 Dimensions Sensors Through-beam* Pre-wired Models EZ-LT6 EZ-LT8. Emitter Lens.5 dia Two, M dia. vinyl-insulated round cable with conductors (Conductor cross section:. mm (AWG), Insulator diameter:. mm), Standard length: m Receiver EZ-LT@-D Indicator EZ-LT/LR/LL (Unit: mm) Tolerance class IT6 applies to dimensions in this datasheet unless otherwise specified. Power Terminal No. Specifications.7 +V --- V --- Pins and are not used. M Pre-wired Connector (EZ-LT@@-MJ) dia. vinyl-insulated round cable with or conductors, Standard length:. m M Pre-wired Connector Models with M8 connectors (Inquire) dia. vinyl-insulated round cable with or conductors, Standard length:. m M8..8 Stability (green) Lens.8 5. Two, M dia. vinyl-insulated round cable with conductors (Conductor cross section:. mm (AWG), Insulator diameter:. mm), Standard length: m selector Sensitivity adjuster Terminal No. cations Specifi-.7 +V --- V Output Pin is not used. Pre-wired Connector Models with M8 -pin connectors (Inquire) dia. vinyl-insulated round cable with or conductors, Standard length:. m M8 * The Emitter cable has two conductors and the Receiver cable has three conductors. Through-beam* Standard Connector Models EZ-LT66 EZ-LT86. Emitter EZ-LT@6-L.8.8 Power Lens.5 dia Two, M Receiver EZ-LT@6-D Indicator M8 -pin connector..8 Stability (green).8 selector Sensitivity adjuster Lens Two, M 9.75 M8 -pin connector * Models numbers for Through-beam Sensors (EZ-LT@@) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: EZ-LT6-L M), the model number of the Receiver, by adding "-D" (example: EZ-LT6-D M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers.

12 EZ-LT/LR/LL Retro-reflective Models Pre-wired Models EZ-LR6 EZ-LR8 Indicator M Pre-wired Connector (EZ-LR@@-MJ) dia. vinyl-insulated round cable with conductors, Standard length:. m. 8.8 Stability (green) Receiver Lens 7 dia selector Sensitivity adjuster 6.7 M Pre-wired Connector Models with M8 connectors (Inquire) dia. vinyl-insulated round cable with conductors, Standard length:. m Emitter Lens.5 dia. Two, M dia. vinyl-insulated round cable with conductors (Conductor cross section:. mm (AWG), Insulator diameter:. mm), Standard length: m Terminal No. Specifications +V --- V Output M8 Pre-wired Connector Models with M8 -pin connectors (Inquire) dia. vinyl-insulated round cable with conductors, Standard length:. m M8 Retro-reflective Models Standard Connector Models EZ-LR66 EZ-LR86 Indicator Stability (green) selector Sensitivity adjuster..8 Receiver Lens 7 dia Emitter Lens.5 dia. 5. Two, M M8 connector Terminal No. Specifications +V --- V Output

13 EZ-LT/LR/LL Pre-wired Models EZ-LL6 EZ-LL8 EZ-LL6 EZ-LL8 Indicator Set distance adjuster Stability (green) selector M Pre-wired Connector (EZ-LL@@-MJ) dia. vinyl-insulated round cable with conductors, Standard length:. m M. 8.8 Receiver Lens 7 dia Pre-wired Connector Models with M8 connectors (Inquire) dia. vinyl-insulated round cable with conductors, Standard length:. m Emitter Lens.5 dia. Two, M -dia. vinyl-insulated round cable with conductors (Conductor cross section:. mm (AWG), Insulator diameter:. mm), Standard length: m and.5 m Terminal No. Specifications +V --- V Output M8 Pre-wired Connector Models with M8 -pin connectors (Inquire) dia. vinyl-insulated round cable with conductors, Standard length:. m M8 Standard M8 Connector Models EZ-LL66 EZ-LL86 EZ-LL68 EZ-LL88..8 Indicator Set distance adjuster Stability (green) Receiver Lens 7 dia selector Emitter Lens.5 dia. Two, M M8 connector 9.75 Terminal No. Specifications +V --- V Output

14 EZ-LT/LR/LL Accessories (Order Separately) Slit E9-S65A Reflector E9-R.. Two,.5 dia dia mm-thick 8 Material SUS stainless steel Materials Reflective surface: Rear surface: Acrylic ABS Reflector E9-R6 Reflector E9-R R Two,. dia. Materials Reflective surface: Rear surface: Acrylic ABS Two,.5 dia..5 Materials Reflector: Polycarbonate (surface) Acrylic (interior) Frame: ABS 7 R.7 Cat. No. E85-E- In the interest of product improvement, specifications are subject to change without notice.

15 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMR's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMR. OMR MAKES NO WARRANTY OR REPRESENTATI, EXPRESS OR IMPLIED, REGARDING N-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMR DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIS OF LIABILITY OMR SHALL NOT BE RESPSIBLE FOR SPECIAL, INDIRECT, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED CTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMR for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMR BE RESPSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMR'S ANALYSIS CFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CTAMINATI, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATI OR REPAIR. Application Considerations SUITABILITY FOR USE OMR shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMR will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMR shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMR representative at any time to confirm actual specifications of purchased products. DIMENSIS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMR s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMR Warranty and Limitations of Liability. ERRORS AND OMISSIS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. OMR Corporation Industrial Automation Company In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation All Right Reserved.