Packaging of Hazardous Materials And Dangerous Goods for Transport
|
|
- Valentine Moody
- 7 years ago
- Views:
Transcription
1 Page 1 Packaging of Hazardous Materials And Dangerous Goods for Transport A Packaging Vocabulary The following terms are used throughout the packaging regulations. These definitions are based on 49CFR Packaging means a receptacle and any other components or materials necessary for the receptacle to perform its containment function in conformance with the minimum packaging requirements. Package means a packaging plus its contents. Bulk packaging means a packaging in which hazardous materials are loaded with no intermediate form of containment and have: A maximum capacity greater than 450 L (119 gallons) as a receptacle for a liquid; A maximum net mass greater than 400 kg (882 pounds) and a maximum capacity greater than 450 L (119 gallons) as a receptacle for a solid; or A water capacity greater than 454 kg (1000 pounds) as a receptacle for a gas. Non bulk packaging means a packaging which has: A maximum capacity of 450 L (119 gallons) or less as a receptacle for a liquid; A maximum net mass of 400 kg (882 pounds) or less and a maximum capacity of 450 L (119 gallons) or less as a receptacle for a solid; or A water capacity of 454 kg (1000 pounds) or less as a receptacle for a gas. Non bulk packaging vocabulary includes: Combination packaging means a combination of packaging, for transport purposes, consisting of one or more inner packagings secured in a non-bulk outer packaging. Single packaging means a non-bulk packaging other than a combination packaging (a single packaging contains no inners).
2 Page 2 Overpack means an enclosure that is used by a single consignor to provide protection or convenience in handling of a package or to consolidate two or more packages. Examples of overpacks are one or more packages: Placed or stacked onto a load board such as a pallet and secured by strapping, shrink wrapping, stretch wrapping, or other suitable means or Placed in a protective outer packaging such as a box or crate. 49CFR General Requirements for Packages and Packagings This section applies to all hazard classes and all configurations, large or small. It applies to bulk and non-bulk packaging. The section serves to create a minimum standard for all levels of packaging. The principal minimum standard is that the packaging must not leak its contents under conditions that are normally incident to transport. Additional minimum standards address: Compatibility Ullage/filling limits for liquids Prohibitions concerning compromised packagings Mixed contents
3 Page 3 The Rule of Packaging Specification Packagings UN Performance Oriented Packagings Packaging requirements vary with the level of risk associated with the materials, however the rule of packaging for most materials is fairly simple; a specification packaging must be used. Of course, many exceptions exist to this rule. Today's modem specification system for many dangerous goods and hazardous materials is a UN Performance Oriented Packaging System. UN packagings go through a series of tests designed to emulate what can happen to a package during routine transport. Drop tests, stack tests, and other testing protocols are performed. UN packagings bear a unique certification marking which is pictured below: The UN employs a series of numbers and letters (4G) to identify the system. In this example, the 4 means the packaging is a box, and the G means it is constructed of fiberboard. Packaging Code Outer Packing 1A1 Steel drum, non-removable head 1A2 Steel drum, removable head 1B1 Aluminum drum, non-removable head 1B2 Aluminum drum, removable head 1D Plywood drum 1G Fibre Drum 1H1 Plastic drum, non-removable head 1H2 Plastic drum, removable head 1N1 Metal Drum, non-removable head 1N2 Metal Drum, removable head 2C1 Wooden barrel, bung type 2C2 Wooden barrel, removable head 3A1 Steel jerrican, non-removable head 3A2 Steel jerrican, removable head 3H1 Plastic jerrican, non- removable head 3H2 Plastic jerrican, removable head 4A Steel box 4B Aluminum box 4C1 Wooden box, ordinary 4C2 Wooden box with sift-proof walls 4D Plywood Box 4F Reconstitued wood box 4G Fibreboard
4 Page 4
5 Page 5
6 Page 6 Packaging Selection HMR The Process Step 1: Once you have determined the correct proper shipping name you must consult Column 7 of the HMT. Please remember that many special provisions are written which can affect your ability to package material. Of particular note are "N" codes which address non bulk packaging. For example, special provision N33 prohibits the use of aluminum drums. Step 2: If you have addressed the issues concerning Column 7, you must consult Column 8 of the HMT. Please remember the role of the three sub columns. Packaging exceptions are listed in Column 8A and non-bulk packaging selection is the role of Column 8B. Step 3: You must always comply with the General Requirements for Packages and Packagings in Remember that compatibility and other issues reside here. Step 4: If using a UN specification packaging, you must verify that the packaging is eligible for the material to be placed inside. For example, a PG I material can only be placed in a system marked with an "X". Remember that combination packages and single packagings for solids have maximum weight limits.un Packaging Assembly, Filling, and Closure Requirements Please remember that most UN packagings are tested systems, meaning that all components, including inners have been tested when assembled and filled with material which closely resembles hazardous material. Generally, the user is not permitted to depart from the assembly and closure requirements. Variation Packaging The V System Articles or inner packagings of any type for liquids and solids can be assembled without testing under certain conditions in Part 178 of the HMR. Known as a variation packaging, the system will bear a "V" marking after the marked packaging code, such as "4GV". This is an excellent method of packaging materials when it is impossible to comply with the requirements of a tested system. Please consult (g)(2). 4GV/X8.2/S/1 2 USA/ABC
Ordering Drums for Hazardous or Non Hazardous Material Transportation
Ordering Drums for Hazardous or Non Hazardous Material Transportation Introduction Selecting the proper steel drum for your company s needs requires a thorough understanding of the product(s) to be shipped,
More informationTechnical Instructions for the Safe Transport of Dangerous Goods by Air
Doc 9284 AN/905 Technical Instructions for the Safe Transport of Dangerous Goods by Air Approved and published by decision of the Council of ICAO 2013-2014 Edition International Civil Aviation Organization
More information10 Importance of UN-approved packaging for dangerous goods
Book it right and pack it tight: shipping containerised dangerous goods by sea Letter of indemnity Letters of indemnity form no part of the IMDG Code, but the shipping line may request one from you as
More informationHazardous Materials Packagings
Hazardous Materials Packagings I. Hazmat Basics Bulk Containers, Non-Bulk Packagings and Intermediate Bulk Containers Packagings and containers used to transport Hazardous Materials are regulated in the
More informationTRANSPORT OF DANGEROUS GOODS
Recommendations on the TRANSPORT OF DANGEROUS GOODS Model Regulations Volume II Sixteenth revised edition UNITED NATIONS ST/SG/AC.10/1/Rev.16 (Vol.II) Recommendations on the TRANSPORT OF DANGEROUS GOODS
More informationDANGEROUS GOODS PANEL (DGP) MEETING OF THE WORKING GROUP OF THE WHOLE
International Civil Aviation Organization 23/3/11 WORKING PAPER DANGEROUS GOODS PANEL (DGP) MEETING OF THE WORKING GROUP OF THE WHOLE Atlantic City, United States, 4 to 8 April 2011 Agenda Item 2: Development
More informationTRANSPORT OF DANGEROUS GOODS
Recommendations on the TRANSPORT OF DANGEROUS GOODS Model Regulations Volume II Seventeenth revised edition UNITED NATIONS ST/SG/AC.10/1/Rev.17 (Vol.II) Recommendations on the TRANSPORT OF DANGEROUS GOODS
More informationTECHNICAL INSTRUCTIONS FOR THE SAFE TRANSPORT OF DANGEROUS GOODS BY AIR
CORRIGENDUM NO. 2 26/4/11 INTERNATIONAL CIVIL AVIATION ORGANIZATION TECHNICAL INSTRUCTIONS FOR THE SAFE TRANSPORT OF DANGEROUS GOODS BY AIR 2011-2012 EDITION CORRIGENDUM NO. 2 The attached addendum/corrigendum
More informationLithium Batteries Significant Changes on the Way
Lithium Batteries Significant Changes on the Way Lithium batteries in all their forms have been the subject of regulatory review through the course of 2006 and 2007. The review process was driven in part
More informationRequirements for packaging, marking and labeling of dangerous goods
INSTRUCTION 1 (1) Requirements for packaging, marking and labeling of dangerous goods Abstract General requirements for packages, packaging preparation and the marking and labels required for packages
More information2002 E D I T I O N INSTRUCTOR
2002 EDITION INSTRUCTOR Script Visual Narrative 1 This module presents general placarding requirements, placarding exceptions, and placard placement and design. Placards are placed on bulk packagings,
More informationHow To Test And Certify Packaging
U.S. Department East Building, PHH 32 of Transportation 1200 New Jersey Avenue, Southeast Pipeline and Hazardous Materials Safety Administration Washington, D.C. 20590 APPROVAL CA2007040012 (FOURTH REVISION)
More informationDepartment of Transportation Hazardous Material Regulations General Awareness, Safety & Security Training. For: University of Dayton Hazmat Employees
Department of Transportation Hazardous Material Regulations General Awareness, Safety & Security Training For: University of Dayton Hazmat Employees February, 2014 Overview Hazardous materials are substances
More informationThe Carriage of Dangerous Goods and Use of Transportable Pressure Equipment Regulations 2009 (as amended) Authorisation No. 284 Rev.
The Carriage of Dangerous Goods and Use of Transportable Pressure Equipment Regulations 2009 (as amended) Authorisation No. 284 Rev.1 Applicable to carriage by road and rail This authorisation is given
More informationThe. can. usually be. the substance. or article. The from. to hazardous. Copyright
Hazardous Materials Training Module 4 - Hazard Communication Unless otherwise accepted, packages must be marked with the correct proper shipping name that has been assigned to the hazardous material. The
More informationUC Davis Guide to Shipping Dry Ice REVISED 06/10/2015 JDC
UC Davis Guide to Shipping Dry Ice REVISED 06/10/2015 JDC 1 Table of Contents Introduction.3 Training Objectives...4 Training Requirements.5 Dry Ice Hazards. 6 Identifying/Classifying Dry Ice.7-12 Packaging
More informationShipping papers must contain the following information. The basic description must be provided in the order prescribed per 49 CFR 172.202.
Hazardous Materials Training Module 6 Documentation Shipping papers are required, under most circumstances, by 49 CFR, Part 172, Subpart C to be prepared and tendered with the shipment and maintained away
More informationPOLY DRUMS. LAB PACK - OVERPACK - SALVAGE DRUMS The Best Drums in the Field CONTENTS: What s the difference?
POLY DRUMS America s All Star Poly Drum Lineup LAB PACK - OVERPACK - SALVAGE DRUMS The Best Drums in the Field What s the difference? These tough drum products handle all of your hazardous material needs.
More informationOFFICIAL MEXICAN STANDARD NOM-003-SCT2/1994
OFFICIAL MEXICAN STANDARD NOM-024-SCT2/1994 SPECIFICATIONS FOR THE CONSTRUCTION AND RECONSTRUCTION, AS WELL AS THE METHODS FOR TESTING THE PACKAGES AND PACKAGINGS OF HAZARDOUS SUBSTANCES, MATERIALS AND
More informationGuide for Preparing SHIPPING PAPERS
Guide for Preparing SHIPPING PAPERS One of the most frequently cited safety violations of the Hazardous Materials Regulations (HMR), Title 49 CFR Parts 100-185, is the failure of the shipper to properly
More informationBudget Basins Modular Spill Platform Spill Containment Pallets Spill Containment Platforms
Budget Basins Modular Spill Spill Containment Pallets Spill Containment s IBC Containment Units Spill Containment Sumps Outdoor Drum Storage Workstations SPILL CONTAINMENT For nearly 30 years, Eagle Manufacturing
More informationGuidelines for Exporters for Completion of Regulation (EC) 1774 Export Certificates
Guidelines for Exporters for Completion of Regulation (EC) 1774 Export Certificates This guidance is intended for Regulation (EC) 1774/2002 certificates formatted to contain the following two sections:
More informationIBC Tote Containment Sumps
IBC Tote Containment Sumps DENIOS Provides More Models- and More Variety of IBC Totes Sumps than any other Manufacturer Painted, Galvanized, Stainless Steel, and Poly models available Models provide storage
More informationIn accordance with NFPA 30, these containers are not to store Class I flammable liquids.
In accordance with NFPA 30, these containers are not to store Class I flammable liquids. Zurich recommends storing these containers in dedicated liquid storage rooms, detached buildings, or in listed dispensing
More informationPointers on Shipping: Clinical Samples, Biological Substance Category B(UN 3373) and Environmental Test Samples
Pointers on Shipping: Clinical Samples, Biological Substance Category B(UN 3373) and Environmental Test Samples At FedEx, we understand the importance of ensuring the safe shipping of clinical samples
More informationFor Components PIERBURG S.A.
Procedure 04 1 / 29 Packaging Terms and Conditions For Components PIERBURG S.A. Modificaciones del documento Versión Capítulo Descripción Fecha Realizado por 00 Versión inicial 14.01.2015 J.M. Galiano
More informationpdi PLASTIC DRUM INSTITUTE Plastic Drum Paneling Issues
pdi PLASTIC DRUM INSTITUTE Plastic Drum Paneling Issues PANELING BACKGROUND This report will explain the causes of paneling and suggest some possible ways to eliminate or minimize the paneling of plastic
More informationPackaged-Products for Parcel Delivery System Shipment 70 kg (150 lb) or Less
Packaged-Products for Parcel Delivery System Shipment 70 kg (150 lb) or Less 3A2 008 ISTA 3 Series General Simulation Performance Procedure VERSION DATE Last TECHNICAL Change: FEBRUARY 2008 Last EDITORIAL
More informationIntermodal Containers Presented by Bill Hand Training Coordinator Hazardous Materials Response Team Harris County, Texas
Intermodal Containers Presented by Bill Hand Training Coordinator Hazardous Materials Response Team Harris County, Texas International Hazmat Response Teams Conference Baltimore, MD 2010 Material in this
More informationGuidelines for the Safe Transport of Infectious Substances and Diagnostic Specimens
Distr.: General Orig.: English Guidelines for the Safe Transport of Infectious Substances and Diagnostic Specimens WORLD HEALTH ORGANIZATION Division of Emerging and Other Communicable Diseases Surveillance
More informationFormal Interpretation NFPA 30. Flammable and Combustible Liquids Code. 2012 Edition
Reference: 1.1, Scope F.I. 84-4 Background: Tank trailers and semi-trailers are loaded with flammable or combustible liquid and moved to a storage yard. There, the tank vehicles may be kept for days, weeks,
More informationRomic Environmental Technologies Corp. Section D. Container and Tank Storage Units. Chandler, Arizona TSD Facility AZD 009015389
Romic Environmental Technologies Corp. AZD 009015389 Chandler, Arizona TSD Facility Section D Container and Tank Storage Units January 2005 TABLE OF CONTENTS D PROCESS EQUIPMENT... D-1 D1 CONTAINERS...
More informationATTACHMENT 12 CONTAINERS
ATTACHMENT 12 CONTAINERS Attachment 12 - Page 1 Table of Contents Table of Contents List of Tables List of Acronyms 12.1 Applicability 12.2 Description of 12.3 Reserved 12.4 Reserved 12.5 Description of
More informationBP WIND ENERGY POLICIES AND PROCEDURES
BP WIND ENERGY POLICIES AND PROCEDURES Document Control Details 1.0 Purpose/Scope 1.1 This procedure provides the minimum requirements to be followed for the storage of flammable or combustible materials
More informationThe entire document shall be read and understood before proceeding with a test. ISTA 3B 2013 - Page 1 of 35
Packaged-Products for Less-Than-Truckload (LTL) Shipment ISTA 3 Series General Simulation Performance Test PROCEDURE VERSION DATE Last TECHNICAL Change: NOVEMBER 2012 Last EDITORIAL Change: JANUARY 2013
More informationII. For Type B parts:...20 III. For Type C parts:...20 IV. For Type D parts:...20 V. For Type E parts:...20 5. Process Changes...
Table of Contents FORWARD... 4 1.0 INTRODUCTION... 5 2.0 PACKAGING DATA... 5 3.0 GENERAL REQUIREMENTS... 5 4.0 PACKAGING REQUIREMENTS... 6 4.1 Package Design...6 4.2 Part Cleanliness and Protection:...6
More informationDrum Dispensing Stations
Drum Dispensing Stations O Safely Dispense from 55 Gallon Drums over a Spill Compliant Sump. 1-2-and 4 drum models available Drums are securely held on racks by galvanized positioners Sump and frame constructed
More informationSPILL CONTAINMENT PRODUCTS
SPILL CONTAINMENT PRODUCTS CHEMISAFE spill containment products help you comply with environmental regulations. Keep your staff safe from accidental slips, protect your workfloor and limit high clean-up
More informationOIL SPILL CONTAINMENT CONTAINERS AND RACKING
www.lubecontrol.com.au OIL SPILL CONTAINMENT CONTAINERS AND RACKING Lube Control Pty Ltd Providing lubrication solutions! Unit 5/53 Norfolk Rd, Marion, SA 5043 t: (08) 8298 5563 f: (08) 8298 6253 e: info@lubecontrol.com.au
More informationJOINT CBA AND SIA GUIDANCE FOR THE STORAGE OF FLAMMABLE LIQUIDS IN SEALED PACKAGES IN SPECIFIED EXTERNAL STORAGE AREAS
JOINT CBA AND SIA GUIDANCE FOR THE STORAGE OF FLAMMABLE LIQUIDS IN SEALED PACKAGES IN SPECIFIED EXTERNAL STORAGE AREAS 1 JOINT CBA AND SIA GUIDANCE FOR THE STORAGE OF FLAMMABLE LIQUIDS IN SEALED PACKAGES
More informationNatural Resources Conservation Authority Guidelines for Secondary Containment of Hazardous Liquids stored Above-ground
Natural Resources Conservation Authority Guidelines for Secondary Containment of Hazardous Liquids stored Above-ground December 2011 Table of Contents Definition of Terms... 2 Requirements for Secondary
More informationENVIRONMENTAL COMPLIANCE PROGRAM
Chapter 4. Handling and Disposal of Hazardous Waste 4.1 Hazardous waste: Hazardous waste is defined in section IV under definitions. The following diagram can aide in the process of determination: Is the
More information4/30/2015. Step - By - Step. Approach to Compliance. Basic 49 CFR Regulations of the U.S.D.O.T. Hazardous Materials Transportation
Hazardous Materials Transportation Compliance, Safety & Security for Hazmat Employees 1 Hazardous Materials Transportation Compliance, Safety & Security Basic 49 CFR Regulations of the U.S.D.O.T. Presented
More informationTesting Packaged Products Weighing up to 150 Lbs.
Testing Packaged Products Weighing up to 150 Lbs. We recommend a series of pre-shipment tests to simulate FedEx air and ground shipping environments. Follow our instructions or let us do the testing for
More informationYFS Automotive Systems, Inc. Supplier Packaging Guidelines
Table of Contents 1.0 Introduction... 2 2.0 Supplier Responsibilities and General Guidelines... 2 3.0 Packaging Data Form... 2 4.0 Expendable Packaging... 2 5.0 Shipping Identification Labels... 3 6.0
More informationPackaging & Shipping Laboratory Specimens Guide Volume XI
Packaging & Shipping Laboratory Specimens Guide Volume XI PAML is not certified to provide regulatory training. This guide is to be used in addition to training and certification by a regulated agency.
More informationTransportation of Dangerous Goods. Transportation of Dangerous Goods Training for Queen s University Shippers and Receivers.
Transportation of Dangerous Goods Training for Queen s University Shippers and Receivers. Welcome to the Transportation of Dangerous Goods (TDG) online refresher/training course specifically designed for
More informationCopyright 1994 2006. Voluntary Interindustry Commerce Solutions Association. All rights reserved.
Voluntary Guidelines for FLOOR-READY MERCHANDISE 9.0 Shipment Packaging 2 nd Ediitiion Latest Reviisiion: September 15, 2006 Copyright 1994 2006 All rights reserved. TTaabbl llee oof f CCoonnt teennt tss
More informationTransporting Batteries
Transporting Batteries RDIMS #5872093 Updated December 2010 This bulletin is divided into 9 items and addresses batteries that are regulated under the Transportation of Dangerous Goods (TDG) Regulations.
More informationHow to prepare a DG Declaration according to IMDG (Amendment 31)
How to prepare a DG Declaration according to IMDG (Amendment 31) 1. (NEW) Continuation Page: Chapter 5.4.1.2.3 requires multiple pages of the DG Declaration be numbered consecutively. PAGE 1 of 2; PAGE
More informationUX-30 PERFORMANCE TESTING SUMMARY REPORT Revision 0
UX-30 PERFORMANCE TESTING SUMMARY REPORT Revision 0 Prepared By: Patrick L. Paquin, EnergySolutions Date Reviewed By: Mirza I. Baig, EnergySolutions Date Approved By: Thomas F. Dougherty, Columbiana Hi
More informationPCB STORAGE. 1) 2-drum unit (4 x 2 x 4 ) 2) 4-drum unit (4 x 4 x 4 ) 3) 8-drum unit (8 x 4 x 4 ) 4) 16-drum unit (8 x 8 x 10 )
PCB STORAGE With the exception of utilities, very few PCB owners are choosing to store their PCB wastes on site. The practice of on-site PCB storage was commonplace before Swan Hills opened up in 1996
More informationAD-A236 607 DODPOPHM/USA/DOD/NADTR9 1107
AD-A236 607 DODPOPHM/USA/DOD/NADTR9 1107,., 4 PERFORMANCE ORIENTED PACKAGING TESTING OF 7 MS-27884-2 METAL DRUM FOR MK 64 MOD 0 GAS GENERATOR BY: BILLIE LANDSTROM a Performing Activity:.. -. Navel Weapons
More informationJAN 2 4 2013. Mr. Marc Covens Vasco Data Security NV Assesteenweg 291 Mollem 1730 Belgium. Ref. No.: 12-0261. Dear Mr. Covens:
U.S. Department of Transportation Pipeline and Hazardous Materials Safety Administration 1200 New Jersey Avenue, SE Washington, D.C. 20590 JAN 2 4 2013 Mr. Marc Covens Vasco Data Security NV Assesteenweg
More informationFIRE DEPARTMENT REPRESENTATIVES WILL INSPECT THE MARKET SUITES DURING MARKET.
CHICAGO FIRE DEPARTMENT RULES & REGULATIONS Exhibitors and retailers must refrain from smoking in the Market Suites at all times. This is for everyone's health and safety and is a Chicago fire department
More informationNorth American Regulations for packaging materials
North American Regulations for packaging materials The North American Plant Protection Organisation (NAPPO) has announced the implementation of a new regulation, applicable for all shipments arriving in
More informationSumitomo Electric Wiring Systems, Inc. Part Identification and Labeling Requirements
1.0 INTRODUCTION These specifications provide guidelines for printing and applying a Shipping/Parts Identification label. Note: In this document, the word must indicates a requirement and the word should
More informationWatts Spacemaker. Sa f e t y Wa t e r He a t e r. Enclosures Stands Restraints
Watts Spacemaker Sa f e t y Wa t e r He a t e r Installation Products Enclosures Stands Restraints Ta b l e o f Co n t e n t s / In t r o d u c t i o n / Seismic Zo n e s Table of Contents Seismic Zones
More informationPART 1 GENERAL PROVISIONS, DEFINITIONS, TRAINING AND SECURITY
PART 1 GENERAL PROVISIONS, DEFINITIONS, TRAINING AND SECURITY - 19 - CHAPTER 1.1 GENERAL PROVISIONS Introductory notes NOTE 1: Recommendations on Tests and Criteria, which are incorporated by reference
More informationNewport News Shipbuilding Contractor Environmental, Health and Safety Resource Manual Waste Management
Newport News Shipbuilding Contractor Environmental, Health and Safety Resource Manual Waste Management Newport News Shipbuilding Page 1 WASTE MANAGEMENT 1. Purpose and Scope a. The purpose of this section
More informationTransportation of Radioactive Material
Haza rdo us Reactor Concepts Manual Transportation of Radioactive Material Santa Fe The issues associated with the transportation of radioactive material are very complex due in part to the regulatory
More informationThe potential to adversely affect human
Purpose and Applicability of Regulations The potential to adversely affect human health and the environment is always present when using, storing, and transporting regulated materials. Consequently, numerous
More informationEXPIRATION DATE: March 31, 2014. 1. GRANTEE: Structural Composites Industries (SCI) Pomona, CA
U.S. Department East Building, PHH 30 of Transportation 1200 New Jersey Avenue, Southeast Pipeline and Hazardous Materials Safety Administration DOT-SP 11382 (TENTH REVISION) Washington, D.C. 20590 EXPIRATION
More informationMIL-STD-2073-1 Standard Practice for Military Packaging
MIL-STD-2073-1 Standard Practice for Military Packaging Presented By: Richard Mast Date 19 July 2011 Revision 5, 7 Jun 2010 Agenda Review the organization and content of the MIL-STD-2073-1 1. Scope Purpose
More informationANNEX 6 EXAMPLES OF ARRANGEMENTS
ANNEX 6 EXAMPLES OF ARRANGEMENTS OF THE GHS LABEL ELEMENTS - 323 - Annex 6 EXAMPLES OF ARRANGEMENTS OF THE GHS LABEL ELEMENTS The following examples are provided for illustrative purposes and are subject
More information(EPA Form 8700 22) and, if necessary, the continuation sheet (EPA Form 8700 22A) for
(EPA Form 8700 22) and, if necessary, the continuation sheet (EPA Form 8700 22A) for . CF = Fiber or plastic boxes, cartons, cases. CM = Metal boxes, cartons, cases (including roll-offs). CW = Wooden
More information2015 DG air transport update
2015 DG air transport update 1 DG Regulations UN Recommendations (Orange Book) IAEA ST-1 (Radioactive Materials) IMO ICAO EC WP15 + National regulations IMDG-Code ICAO-TI IATA ADR IATA-DGR RID 2 IATA DGR
More informationRe: Pallets, Platforms or Skids, for lift trucks, plastic, with or without steel reinforcement
Re: Pallets, Platforms or Skids, for lift trucks, plastic, with or without steel reinforcement CCSB Contact: Donald A. Newell Telephone (703) 838-1890 newell@nmfta.org Proponent: Mercury Marine, Fond du
More informationHow to Package and Ship. Cremated Remains
How to Package and Ship Cremated Remains Publication 139 October 2014 How to Package and Ship Cremated Remains The United States Postal Service offers the only legal method of shipping cremated remains
More informationUS DMF* TYPE III FOR FIBER BOARD DRUMS FOR PHARMACEUTICAL PACKAGINGS
US DMF* TYPE III FOR FIBER BOARD DRUMS FOR PHARMACEUTICAL PACKAGINGS Mr. R.M. Gupta (M. Pharm.), is a free lance consultant for US DMF, COS, ANDA, ACTD, CTD, ectd and other regulatory submissions. guptarmg1952@gmail.com
More informationCOIL PAC. Subec AB, Sprängarvägen 16, 132 38 Saltsjö-Boo, Sweden, Tel.: +46 8 884633, Fax: +46 8 977658, e-mail: info@subec.se
COIL PAC Subec AB, Sprängarvägen 16, 132 38 Saltsjö-Boo, Sweden, Tel.: +46 8 884633, Fax: +46 8 977658, e-mail: info@subec.se Description of the machine Coil Pac 240 und Coil Pac 400 are two types of
More informationM3463. Leader s Guide
M3463 DOT HAZMAT GENERAL AWARENESS TRAINING Leader s Guide 1998, MARCOM GROUP LTD. DOT HAZMAT GENERAL AWARENESS TRAINING This easy-to-use Leader s Guide is provided to assist in conducting a successful
More informationFedEx Ship Manager Software Help Guide
FedEx Ship Manager Software Help Guide January 2016 Designed by: FedEx Express Global Learning Technology FedEx Express World Headquarters 3670 Hacks Cross Road Building G, 2nd Floor Memphis, TN 38125
More informationDenver Fire Department Idle Pallet Storage Guidelines Per NFPA 13_Chpt 12
Idle wood and plastic pallets introduce a severe fire condition. Stacking idle pallets in piles is the best arrangement of combustibles to promote rapid spread of fire, heat release, and complete combustion.
More informationTRANSPORT OF DANGEROUS GOODS
ST/SG/AC.10/1/Rev.16 (Vol.I) Recommendations on the TRANSPORT OF DANGEROUS GOODS Model Regulations Volume I Sixteenth revised edition UNITED NATIONS New York and Geneva, 2009 NOTE The designations employed
More informationTransport of Biological Materials
Transport of Biological Materials Covering the classification, packaging and labelling of biological materials for transport in the UK and abroad Dr Joanna Marshall University Biological Safety Adviser
More informationLithium Primary/Metal Battery Transportation
Energizer Battery Manufacturing, Inc. 25225 Detroit Road Westlake, Ohio 44145 (440) 835-7500 Phone (440) 899-6028 Fax Lithium Primary/Metal Battery Transportation Contents 1) Introduction... 2 2) Within,
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: KRUD KUTTER Rust Remover & Inhibitor Synonyms: Not applicable Molecular Formula: Not applicable Molecular Weight: Not applicable
More informationPAAM COMMERCIAL PRIVATE LIMITED
METAL PACKAGING We at Paam Group have been providing vast range of packaging products to our customers based on their preferences, needs and specifications. We provide all the materials required in metal
More informationStatic Spark Ignites Flammable Liquid during Portable Tank Filling Operation
Static Spark Ignites Flammable Liquid during Portable Tank Filling Operation No. 2008-02-I-IA (September 2008) Key Lessons for Safe Handling and Storage of Flammables Ensure that equipment, such as fill
More informationBUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof.
BUILDING MATERIALS, Wood, Laminated (Page 1 of 3) Viz.: Rafters; Arches; Beams; Joists; Timbers or Planks, structural or roof. 1155 & 4155 LCL: Applies to all freight in less than container load quantities.
More informationManaging Waste Chemicals for Disposal
Managing Waste Chemicals for Disposal Purpose & Content Define the process for managing waste chemicals on site: Key Legislation: Cost: Curtin University Procedures Outcomes Participants should leave this
More informationDOT 126F Hazardous Material Awareness. Oregon State University Environmental Health and Safety
DOT 126F Hazardous Material Awareness Oregon State University Environmental Health and Safety Why is Training Required Hazardous Materials Employee training requirements of CFR49 Parts 171-177 As stated
More informationRecycling Material Identification Guide
Recycling Material Identification Guide 1 Recycling of Lead-Acid Batteries at Exide Technologies Lead-acid batteries received at Exide s recycling facilities are shredded or otherwise disassembled, and
More informationPackaging Perishable Shipments
Packaging Perishable Shipments To help prevent spoilage and maintain product integrity, follow these instructions for shipping your perishable items via FedEx Express services. Preparing Perishable Items
More informationCarriage of dangerous goods ADR Transport 2014
Factsheet Carriage of dangerous goods ADR Transport 2014 Looking to transport hazardous chemicals? What do you need to do now? Please consult the material safety data sheet (MSDS) for your hazardous substances,
More informationKroger Manufacturing Trailer Seal Policy Revised 09/03/10
Kroger Manufacturing Trailer Seal Policy Revised 09/03/10 1 Inbound Supplier After the product is loaded and the trailer doors are closed, the supplier (or shipping warehouse) is responsible for affixing
More informationItemized RAI Responses
Itemized RAI Responses Question 1-1: Justify the use of a tapped bar or equivalent with a helicoil insert. This justification should specifically address any reduction in packaging performance from the
More informationSafe Operating Procedure
Safe Operating Procedure (Revised 10/14) SHIPPING ITEMS WITH DRY ICE THAT ARE NOT OTHERWISE DANGEROUS GOODS This Standard Operating Procedure (SOP) describes how to prepare a shipment containing dry ice
More informationContainer Management for Hazardous Waste Generators Technical Guidance Document HW-2005-G1
Kansas Department of Health and Environment Bureau of Waste Management 1000 SW Jackson, Suite 320, Topeka, Kansas 66612-1366 Container Management for Hazardous Waste Generators Technical Guidance Document
More informationHow To Safely Handle A Spill
WD DWGB 22 6 2010 Best Management Practices for Fueling and Maintenance of Excavation and Earthmoving Equipment Env Wq 401, Best Management Practices for Groundwater Protection, applies to a variety of
More informationDivision of Public Health Administrative Manual
PURPOSE To establish a protocol for the development of a written Division of Public Health Hazard Communications Program at each applicable office or laboratory workplace and to assure that employees are
More informationNECESSARY DOCUMENTATION ACCORDING TO the LAW
1 NECESSARY DOCUMENTATION ACCORDING TO the LAW According to the Law, your company is obliged to submit monthly reports prepared based on the manufacturing specifications and the monthly sales report. Manufacturing
More informationPackaging Information for Vendors Engineer Approved Hard Copies Uncontrolled. Verify Revision Prior to Use.
1 of 7 This specification is provided to inform vendors of Systems Company's minimum packaging requirements. This document is superseded by any special requirements listed on drawings or specifications.
More informationBerea College Chemical waste/product Management Guide. October 2014
Berea College Chemical waste/product Management Guide October 2014 Chemical Waste Chemical waste is generated in many locations across campus. Chemical waste is generated in laboratories, from painting
More information