Teacher Answer Key: Measured Turns Introduction to Mobile Robotics > Measured Turns Investigation

Transcription

1 Teacher Answer Key: Measured Turns Introduction to Mobile Robotics > Measured Turns Investigation Phase 1: Swing Turn Path Evaluate the Hypothesis (1) 1. When you ran your robot, which wheel spun? The left wheel, the wheel driven by the motor on port C, should be the one to spin. 2. Observe the shape traced by the tracer on the paper. Remember that the tracer approximates the position of the robot s left wheel, but is not exactly on top of it. i. What shape did the wheel trace on the paper? The wheel should have traced out a circle on the paper, which is represented by the mark that the pen left, but is not exactly the same circle. If the tracer did not leave a perfect circle, encourage students to try running the robot again. The robot or the paper may have shifted somewhere during the turn, causing the circle to not line up correctly. It is also possible that the surface is slanted, which will lead to a skewed tracing. ii. What part of the robot is at the center of the circle? At this point, the robot should have pivoted around its right wheel, which stays in place as it turns. iii. What part of the robot ran along the circumference of the circle? The left wheel, which is attached to Motor C, ran along the circumference of the circle. iv. Are these observations consistent with the first part of the hypothesis. Yes, the wheel traced out a circle on the paper, which is exactly what was predicted in the first part of Dr. Turner s hypothesis. Hypothesis (part 1) As the robot swing-turns, the moving wheel traces out a portion of a circle. 3. Measure the path traced by the robot s wheel. i. What is the diameter of the traced circle? The radius of the traced circle should be just about the distance between the two wheels on the robot. It is measured to be approximately 14.5cm (15cm if you re rounding) on Taskbot. Therefore, the diameter should be 29cm (30cm if you re rounding). ii. What is the circumference of the traced circle? The circumference is equal to the diameter times pi. In our example, it is about 91.1cm. iii. Rewrite Dr. Turner s hypothesis equation, filling in the values you have now calculated. The hypothesis equation is as follows: Hypothesis (equation form) 1/8

2 (Angle Turned / 360 degrees) = (Distance traveled by wheel / 91.1cm) We know that the circumference of the traced circle is 91.1cm, so we can fill that in. We also know that a full circle is equal to 360 degrees. Phase 2: Hypothesis Part 2 Answer the following: 4. There is an important distinction between the circumference of a wheel on your robot and the circumference of the circle your robot traces. i. Explain the difference. The circumference of the wheel is the distance around the perimeter of the wheel. The circumference of the circle your robot traces is the distance along the perimeter of the circle around which the robot turns. The circumference of the wheel should be much smaller than the circumference of the circle. ii. Which one is used, along with motor axle rotations, to calculate distance traveled? The circumference of the robot s wheels is used to calculate distance traveled. Recall that distance traveled is equal to the number of motor axle rotations multiplied by the circumference of the robot s wheels. iii. Which one can be measured by placing a marker near the outside wheel of your robot and programming it to turn? The circumference of the circle your robot traces can be measured by placing a marker or pen near the outside wheel of your robot and having it turn. The robot will drag the marker along with it, thereby tracing the path of its outside wheel, and nicely illustrating the circle around which the wheel travels as the robot turns. 2/8

3 Phase 2: Calculate for a 90-degree Turn Calculate the following: 5. Following along with the calculations in the video (using your own numbers), determine how many motor degrees you need to set in your program to make the robot turn 90 degrees. Students will calculate this following the example in the video. Below is a sample calculation. The sample numbers used are that we want the robot to turn 90 (AngleTurned = 90 ), the circumference of the traced circle is 72cm, and the circumference of the wheel is 25cm. Replace these numbers with ones specific to the problem when checking student answers. From the hypothesis equation: AngleTurned 90 = DistanceTraveled = = DistanceTraveled Full Circle Circumferenceof Traced Circle cm Now we can use that equation to solve for Distance Traveled 90 DistanceTraveled = 72cm = 18cm 360 Now that we have the distance that the wheel needs to travel, we can use the equation from the Wheels and Distance Investigation to determine the number of rotations necessary to make the robot go this distance. DistanceTraveled = Wheel Circumference Wheel Rotations Substituting known values into this equation gives us DistanceTraveled = Wheel Circumference Wheel Rotations = 18cm = 25cm Wheel Rotations We can solve that equation for Wheel Rotations by dividing both sides by the Wheel Circumference. 18cm Wheel Rotations = = cm And now, to convert the number of rotations into the necessary number of degrees, we need to multiply the rotations by 360, which is the number of degrees in a full circle. Degrees toturn = Wheel Rotations 360 = = 259 For this example robot, the wheel needs to be set to go 259 to make the robot turn 90 degrees. Analysis and Conclusions: Conclusions 6. Now that you ve run your program, answer the following questions: i. Did your robot turn about 90 degrees? If not, what factors may have caused the difference? This will depend on the student. It is unlikely that they will have calculated what is necessary to make the robot turn 90 degrees on the very first try. Most students will want to use trial and error to revise their calculated number, until they have the robot turn what they see as exactly 90 degrees. In fact, it is almost impossible to measure the exact amount the robot turned at all without highly sensitive scientific equipment, so it is mostly a matter of judgment. 3/8

4 Factors such as surface friction, kickback in the motors, and squishiness of the tires all play a roll in the precision of the robot s turn. Also, note that we used measurements from the traced circle to determine the radius of the turn, and not from the robot itself. So even if the calculations were spot-on, a robot still may not have made a precise 90-degree turn. ii. Does this behavior support the hypothesis? Why or why not? Yes, the hypothesis is supported by this behavior. In most cases, the students will have been close the first time. It will be the factors of the physical world that will have impeded the robot s performance. Because many students will see their robot as having done a turn close enough to a 90-degree turn, this would support the hypothesis. The hypothesis states that as the robot turns, each of its wheels traces out a portion of a circle. This is evident by the path left on the paper by the tracer. The left wheel traces out a circle, and the right wheel traces out a point (or a circle with radius equal to zero). The hypothesis also states that the fraction of a full circle that the wheel travels is equal to the fraction of a full turn that the robot will do. Students worked backwards to get to this point. They started by being asked how to get the robot to do one quarter of a full turn, and worked out how many degrees the wheel needed to travel in order to turn one quarter of the circumference of the circle. And, when they ran their programs, the robot did go approximately one quarter of a turn, so this all supports the hypothesis. iii. Do you now have enough information to say whether or not the hypothesis is valid, or do you need more information? The information from this experiment clearly supports the first part of the hypothesis: that as the robot swing-turns, the moving wheel traces out a portion of a circle. This can be seen simply by looking at the shape left on the paper by the tracer. It also supports the second part of the hypothesis: the amount the robot turns is proportional to the portion of the circle that the wheel travels. Students have made the wheel travel a specific amount along the circumference of the circle (one fourth of the circumference), and they can see that to robot makes on fourth of a full turn, or a 90-degree turn. However, this does not give us enough information to say definitively whether or not the hypothesis is valid. This is only one example. For real scientific validity, many more examples of this behavior must be found and recorded that fit the model proposed by the hypothesis. More information is most certainly needed. 7. Recall the number of motor degrees you used to make the robot turn 90 degrees using a swing turn. Estimate how many degrees the motor would need to spin to turn the robot: All of these estimates are multiples of the original value they have to make the robot turn 90 degrees that they wrote in Question 5. We will assume that it takes about 450 degrees of motor rotation to make the robot turn 90-degrees. i. 180 degrees To turn the robot 180 degrees, students would need to double the number for 90-degrees, which would give them 900 degrees that the motor would need to turn. ii. 270 degrees For a 270-degree turn, the original number would be tripled, or iii. 360 degrees A full turn of 360 degrees is four times the original number, or 1800 degrees. iv. 2 full turns Two full turns is equal to the robot turning 720 degrees, which is 8 times as much as the original 90 degree turn, so students would multiply the original number by 8 to get 3600 degrees. 4/8

5 8. Modify your program and run the robot for the amounts you predicted for each of the angles in the Question 7. i. 180 degrees ii. 270 degrees iii. 360 degrees iv. 2 full turns v. Do these new results support or refute the hypothesis? The students answers will vary, but if they obtained the correct results in Question 7, the new results ought to support the hypothesis. 9. The tracer was close to, but not exactly under the wheel when you ran the robot. As such, the circle it traced was not exactly the path the wheel traveled. Your robot attempted to turn for 90 degrees based on calculations made using the tracer s path instead of the actual wheel. i. What was the actual distance between the tracer tip and the point where the wheel touched the ground? The students must measure this distance. The value should be no more than 5cm. ii. How successful was your robot in turning 90 degrees using the estimate rather than the exact value? Due to experimental errors, this answer may vary from student to student. The actual distance that matters, however, is the distance from the stationary wheel to the pen tip, as opposed to the distance from the stationary wheel to the moving wheel. If you were to measure these two distances, you would find that they are approximately a half centimeter different. Adding a half centimeter to the radius of the circle (which is what you do when you measure the traced circle) adds about 3cm to the circumference. So the circumference that the students found is about 3cm larger than the circumference that the actual wheel travels (which is obtained by measuring the wheel-to-wheel distance). Over one-quarter of the circle, the change in distance is approximately 0.75cm, which leads to an extra 50 degrees of motor rotation. So, if anything, the robots should have gone farther than they needed to (though not by much!) because of the simplification of measuring the traced circle and not the robot s wheel-to-wheel distance. However, due to random factors like friction, it is possible that the robot did run very close to 90 degrees. So answers will depend on the student. iii. Would you say this was a good estimate, based on the results you got from using it? Since the estimate will in general be close to a 90degree turn, it should be considered a good estimate. iv. Since the right wheel stays planted and the left wheel moves, what is the actual physical distance of the radius or diameter of the turn? The actual physical distance of the radius of the turn equals the distance between the two wheels on the robot. This should be approximately 13.8cm. 10. Vehicle designers in the real world deal with turning issues all the time. It is important for both safety and performance that they know exactly what their vehicles can and cannot handle. Think about real world vehicles while you answer the following questions. i. What are the limitations of swing turns? One of the limitations of swing turns is that they are very wide turns, and take up a lot of space for the robot to get all the way around and back to its starting point. This can be a problem in tight spaces. 5/8

6 ii. Name another mobile vehicle that is capable of a swing turn, and estimate its turning radius (or diameter). Almost any mobile vehicle will do swing turns. Cars have turning radii of between 25 and 50 feet. Small mowing tractors have radii of between 2 and 5 feet. Larger farm equipment have turning radii of between 10 and 30 feet. The zamboni at the ice rink has a turn radius as small as 10 feet. iii. Do normal cars use this type of turn? Yes, normal cars can swing turn. They cannot point turn. Analysis and Conclusions: Exercises 11. Shante s robot has wheels that are 4.5 cm in diameter and traces a turning circle with a 12.4 cm radius. Her wheels are driven directly by the motors on each side. She needs her robot to make a swing turn of 210 degrees. How many degrees do her motors need to run in order to make the robot make this turn? Show your work degrees, or approximately 1200 degrees. To do this problem, let s first divide up what we know, and what we want to find. We want to find: Degrees the motor needs to spin We have: Wheel diameter Wheel-to-wheel distance Amount robot must turn We still need: Circle circumference Wheel circumference The circumference of the circle that the robot turns can be found from the wheel-to-wheel distance and the fact that it is a swing turn. For the swing turn, the radius of the circle was equal to the wheel-to-wheel distance on the robot. So the circumference of the circle is equal to the wheel-to-wheel distance times 2 times pi. Circle Circumference = Wheel-to-wheel distance x 2 x pi = 12.4cm x 2 x 3.14 = 77.9cm The wheel circumference is found from the diameter of the wheel. Wheel Circumference = wheel diameter x pi = 4.5cm x 3.14 = 14.1cm The robot must turn 215 degrees, which is (215/360), or 0.6 revolutions. If 77.9cm represents the circumference of the whole circle, then (77.9cm x 0.6) represents 0.6 of a turn around that circle, which is the amount covered by 215 degrees. Distance wheel must go = Circle Circumference x amount robot must turn = 77.9cm x 0.6 = 46.7cm Now we divide the distance the wheel must go by the distance the wheel goes per revolution (the wheels circumference) to get the number of revolutions that the wheel must do. 6/8

7 Revolutions = Distance wheel must go / wheel circumference = 46.7cm / 14.1cm = 3.3 revolutions Degrees the motor needs to spin = Revolutions x 360 = 1188 degrees 12. Larry has forgotten to save his program, and now he can t remember what he had his Wait For block set to. He knows that he wanted his robot to do a swing turn, and he measured his wheels to find out that they are 2.5 cm in diameter and they are 9.0 cm apart. He also knows that the robot turned exactly 180 degrees. How many degrees should Larry set his Wait For block to when he rebuilds his program? Both motors will need to be set to spin 1290 degrees. Again, let s first divide up what we know, and what we want to find. We want to find: Degrees the motor needs to spin We have: Wheel diameter Wheel-to-wheel distance Amount robot must turn We still need: Circle circumference Wheel circumference The circumference of the circle that the robot turns can be found from the wheel-to-wheel distance and the fact that it is a swing turn. For the swing turn, the radius of the circle is equal to the wheel-to-wheel distance on the robot. So the circumference of the circle is equal to the wheel-to-wheel distance times 2 times pi. Circle Circumference = Wheel-to-wheel distance x 2 x pi = 9.0cm x 2 x 3.14 = 56.5cm The wheel circumference is found from the diameter of the wheel. Wheel Circumference = wheel diameter x pi = 2.5cm x 3.14 = 7.9cm The robot must turn 180 degrees, which is (180/360), or 0.5 revolutions. If 56.5cm represents the circumference of the whole circle, then (56.5cm x 0.5) represents 0.5 of a turn around that circle, which is the amount covered by 180 degrees. Distance wheel must go = Circle Circumference x amount robot must turn = 56.5cm x 0.5 = 28.3cm Now we divide the distance the wheel must go by the distance the wheel goes per revolution (the wheels circumference) to get the number of revolutions that the wheel must do. Revolutions = Distance wheel must go / wheel circumference = 28.3cm / 7.9cm = 3.6 revolutions Degrees the motor needs to spin = Revolutions x 360 = 1.8 x 360 = 1290 degrees 13. Below is Peter s program. Assume that the comment he wrote accurately describes the amount the Wait For block will wait. He wants his robot to make a full 180 degree swing turn, and his robot traces a circle with a radius of 10.8 cm. He has a choice between two wheel sizes: 4.6 cm in diameter and 7.2 cm in diameter. 7/8

8 i. Which wheels should he choose to come closest to making the 180 degree turn with his current program? The 4.6cm diameter wheels are the best ones to use. To find this out, students will need to do the math for both wheels. Some things are the same for both wheels, like the diameter of the circle that the rolling wheel will travel. Because this is a swing turn, the large circle s radius is the distance between the two wheels. Circle Diameter = wheel-to-wheel distance x 2 = 10.8cm x 2 = 21.6cm Circle Circumference = Circle Diameter x pi = 21.6cm x 3.14 = 67.8cm And for both wheels, we know we want them to travel around 180 degrees of that circle, which is (180/360) or 0.5 of the circle. Distance the robot needs to travel = Circle circumference x 0.5 = 67.8cm x 0.5 = 33.9cm OK, so now we know that whatever wheel we use has to travel 33.9cm in order to go around half the circle, which would turn the robot 180 degrees in a swing turn. Now we have to figure out which wheel comes closest to this as it goes the number of degrees that Peter set in his program. In his program, Peter has the Wait For block waiting for 760 degrees. Number of motor revolutions = 760/360 = 2.11 turns of the motor We can do the last part one of two ways. First method: Divide the distance the robot needs to go by the number of turns the wheel will make to get the necessary wheel circumference. Wheel Circumference = Distance robot needs to go / Turns of the motor = 33.9cm / 2.11 revs = cm And now find which wheel has a circumference closest to 16.07cm. Wheel 1 Circumference = Wheel 1 Diameter x pi = 4.6cm x 3.14 = 14.4cm Wheel 2 Circumference = Wheel 2 Diameter x pi = 7.2cm x 3.14 = 22.6cm Second Method: Find the circumference of each wheel, and multiply them each by the number of revolutions to find out how far they will travel under that number of revolutions. Wheel 1 Circumference = Wheel 1 Diameter x pi = 4.6cm x 3.14 = 14.4cm Wheel 1 Distance traveled = Wheel 1 Circumference x revolutions = 14.4cm x 2.11 rev = 30.4cm Wheel 2 Circumference = Wheel 2 Diameter x pi = 7.2cm x 3.14 = 22.6cm Wheel 2 Distance traveled = Wheel 2 Circumference x revolutions = 22.6cm x 2.11 rev = 47.7cm The distance the wheel needs to travel was found above to be 33.9cm, and 30.4cm is clearly closer to 33.9cm than 47.7cm is. He should choose the wheels that are 4.6cm in diameter. ii. What else can he change on the robot to make the turn? Peter can also move the wheels farther apart by adding bushings to the axle. This will make the turn wider, increasing the circumference of the turned circle. Or he can change the gear ratio, so that even if the motor spins one full revolution, the wheel may turn less than one full revolution (or more than one full revolution), which will change the amount the robot goes. 8/8