INSTRUCTIONS FOR MAG LASER BORESIGHTING SYSTEMS: SL-100, SL-150, SL-500 (IMPORTANT - READ ALL INSTRUCTIONS PRIOR TO USE)

Transcription

1 INSTRUCTIONS FOR MAG ASER BORESIGHTING SYSTEMS: S-100, S-150, S-500 (IMPORTANT - READ A INSTRUCTIONS PRIOR TO USE) WARNING! UNOAD FIREARM BEFORE PROCEEDING! Physically Check Firearm Do Not Assume it is Unloaded The S-100/150/500 aser boresighters project a laser beam onto a calibrated target for superior boresighting accuracy. The Siteite boresighters are ideal for use with conventional & red dot scopes as well as open sights. The boresighters fit most calibers (Rifles, Pistols &.50 Cal. Muzzleloaders). A 20Ga. and 12Ga. Shotgun Adapter is also included. The S-100/150/500 are delicate, precision instruments and must be handled with care.

2 WARNING! UNOAD FIREARM BEFORE PROCEEDING! ASER SAFETY PRECAUTIONS The S-100/150/500 aser Boresighters use a Class IIIa laser with a /- 10NM wavelength and a maximum output of 5.0mW. It is safe to use in normal operation as described in se instructions. The S-100/150/500 have warning labels in compliance with applicable regulations, as shown. AVOID DIRECT EYE EXPOSURE - DO NOT OOK DIRECTY INTO THE ASER IMPORTANT! This is an Actual Photo of a Customer Who Forgot to Unload Their Rifle. This Can Happen to You, if You Do Not Heed This Warning! AVOID EXPOSURE ASER IGHT IS EMITTED FROM THIS APERTURE S MAG ITE ASER NOTE: THE BATTERY CAP THREADS & HOUSING MAY DEVEOP AN INVISIBE OXIDATION OVER TIME, THEREFORE, THE THREADS MAY NEED TO BE BUFFED (VERY IGHTY) TO REMOVE THE AUMINUM OXIDATION. IT IS RECOMMENDED TO USE STEE WOO OR A PENCI ERASER TO REMOVE THE OXIDATION. THIS WI INSURE A GOOD EECTRICA PATH. CHECK THIS, FIRST, IF THE ASER DOES NOT TURN ON PROPERY. + No. 357, R44, 1154 (S-100) Physically Check Firearm Do Not Assume it is Unloaded DANGER AVOID DIRECT EYE EXPOSURE CASS IIIa ASER PRODUCT WAVEENGTH 530 TO 670NM MAX. OUTPUT 5mW COMPIES WITH 21CFR & CR2 ITHIUM BATTERY (S-150) + D123 ITHIUM BATTERY (S-500) +

3 S ASER ITE S ASER ITE S ASER ITE S ITE ASER S ASER ITE S ITE ASER Preferred Boresighting Method The Ballistic Targeting System (BTS) Software Program will create a custom laser boresighting target for your specific rifle and ammo. It is most accurate boresighting method available. BTS Software Program Download Instructions To download program, go to and click on Ballistic Targeting System button on left side of page. Then, scroll down to and click on Ballistic Targeting System - Download ocate Serial No. on your boresighter: Serial No. S MAG ITE ASER Enter only six numbers of Serial No. and press OK. Save program to your Desktop. Then click on sitelitesetup to install program and save Sitelite Sight-in Program to your Desktop. To initiate program, click on Sitelite Sight-in Program icon. IMPORTANT: When program first opens, Scroll Down to Read A Instructions BEFORE Proceeding Note: If data is not available for your specific firearm, use a caliber that has similar ballistics and put in your bullet weight, sight height, FPS, etc. Data is not available for muzzleloaders except from specific manufacturers. However, you can use Remington 44 Mag Rifle data and put in bullet weight, sight height, FPS, etc. for your muzzleloader and that will get you very close. BTS Program BTS Program - Basic - Steps Basic Steps BTS Program - Basic Steps 1. Select Rifle, Pistol or Shotgun. BTS Program - Basic Steps 1. Select 1. Select Rifle, Rifle, Pistol Pistol or Shotgun. or Shotgun. 2. Select caliber/cartridge for rifle you are using (.222,.270, 1. Select Rifle, Pistol or Shotgun ,.300 WSM, etc.) Enter Select caliber/cartridge scope height. for Determine rifle you are using height (.222, by. 270, measuring.30-06,.300 WSM, etc. ) distance of of rifle rifle from bore bore to to center-line center-line of of of scope scope (Fig. rifle 1) (Fig. bore 1) to center-line 3. of Enter scope height. (Fig. Determine 1) height by measuring distance from center-line 2. Select 2. Select caliber/cartridge for for rifle you rifle are you using are using (.222,(..222, 270,.30-06,. 270,.30-06,.300 WSM,.300 etc. WSM, ) etc. ) 3. Enter 3. Enter scope scope height. height. Determine Determine height height by measuring by measuring distance distance from from center-line center-lin of rifle bore to center-line of scope (Fig. 1) Scope Ht. Fig. Scope 1 Ht. Scope Ht. 4. Select bullet weight. 4. Select 4. Select bullet weight. 4. Select bullet weight Select bullet bullet shape shape (round nose, (round pointed, nose, hollow-point, pointed, etc.) hollow-point, etc.) 5. Select bullet shape (round nose, pointed, hollow-point, etc.) Select bullet Muzzle shape (round Velocity nose, (FPS) pointed, (If hollow-point, unknown, etc.) 6. Enter Muzzle Velocity (FPS) (If unknown, system will enter system average will FPS) enter 6. average Enter Muzzle FPS) Velocity (FPS) (If unknown, system will enter average FPS) 6. Enter Muzzle Velocity (FPS) (If unknown, system will enter average FPS) 7. Enter B.C. (If unknown, system will enter average B.C.) Enter B.C. B.C. (If unknown, system system will enter will enter average B.C.) average B.C.) 7. Enter B.C. (If unknown, system will enter average B.C.) Select Zeroed Range Range (75 to ( yds to in yd yards increments) 25 yard increments) 8. Select Zeroed Range (75 to 300 yds in 25 yd increments) Select Zeroed enter Range (75 to zeroed 300 yds in 25 range yd increments) 9. Once you enter "zeroed" range program will program calculate will boresighting calculate range that boresighting 9. Once you enter target "zeroed" range that range you program should will use calculate to align boresighting center 9. Once you should you enter use to align "zeroed" range center of your program crosshair will calculate with laser boresighting spot (Fig. 2) range This range that range tha of you will your should be closer should crosshair use than to use align to with "zeroed" align center range center of laser your because of crosshair spot your it crosshair (Fig. is with point 2) with laser This where spot range laser (Fig. bullet spot 2) will This crosses (Fig. range be 2) This over range closer will line be will of closer sight than be closer and than is than zeroed "zeroed" same "zeroed" point range range that because range bullet because it is will point it it impact is is where point at point where selected bullet where crosses range bullet over (Fig. crosses 3) ove bullet line of line sight crosses of sight and is and over is same point same line that point of sight that bullet and will bullet impact is will at impact same selected at point range selected that (Fig. range 3) (Fig. 3 bullet will impact at selected range (Fig. 3) Fig. 2 Fig. 4 Boresighter Target Range Fig. 3 3 Boresighter Target Range 4 Boresighter Target Range Note: Boresighting with this system, at zeroed range, will usually require it to be done in dim light or use reflective dot on SAVS Target (Ref. Page 14) You may also select a closer range (Minimum 8 yards) for use indoors. The system will move laser target position below crosshair position, to compensate for range difference (Fig. 4) Bullet Path Bullet Path Bullet Path ine of Sight ine of Sight ine of Sigh Zeroed Range Zeroed Range Zeroed Range

4 WARNING! UNOAD FIREARM BEFORE PROCEEDING! Physically Check Firearm Do Not Assume it is Unloaded 5. Insure that firearm does not move and that laser remains centered in target while making adjustments. 5. Insure that firearm does not move and that laser remain centered Adjust in scope target crosshairs while making or adjustments. or type sights Adjust to align scope as shown crosshairs in Fig. or or 1 & 2 type sights to align as shown in Fig. 1 & 2 Alternate Boresighting Method 1. Place target on a wall 25 feet from muzzle. 2. The firearm must be secured and clamped into position with muzzle located at 25 feet from target. The barrel should be level in relation to target. 3. Install proper o-ring and screw on Muzzle Adapter, as required (see Muzzle Adapter Instructions). Insert boresighter all way into muzzle, with arrow aligned with top center of barrel. ubricate o-ring with Vaseline or silicone grease before inserting. Do not use gun oil. Some oils will swell and deteriorate o-ring. (O-rings will tear without lubrication) 4. Set scope at low power and switch on boresighter. Adjust position of firearm to center laser within aser Target located below dotted line crosshair on target (See Fig. 1.) Note: The laser spot, projected on target, will normally range in size from 1/2 to 3/4 in diameter. This provides for easier alignment on target. aser Spot S ASER ITE Fig. 1 Fig. 2 Properly Properly boresighted boresighted scope scope with laser spot with laser spot on aser on "aser Target" and Target and scope crosshairs on dotted lines above scope crosshairs on dotted lines above laser spot laser spot aser Spot Properly Properly boresighted boresighted iron iron sights with laser spot on sights with laser spot on "aser Target" aser Target 6. Complete sighting in firearm at range, taking 6. Complete sighting in firearm at range, taking first first shots at no more than 50 yards to make your initial shots at no more than 50 yards to make your initial adjustments. adjustments. S ASER ITE 5 6 Page 3.

5 o-ring to caliber selection chart.243 CA. B.25 TO.270 CA. B.284(7MM).323 (8MM) TO.338 B.35 CA. & 9MM.375 CA..40 CA..44 CA..45 CA..50 CA A A A A A A A MATCH O-RING TO CHART (ACTUA SIZE) MATCH O-RING TO CHART (ACTUA SIZE).308 CA. O-RING Do not remove se o-rings.22 CA. O-RINGS Place.50 Cal O-ring here for.50 Cal Muzzleoader ONY SCREW ON THIS ADAPTER FOR CA. BORES * A B SHOTGUN ADAPTER * The lubricated O-ring should insert with a light drag. Due to varying tolerances in different bores & calibers, O-ring can be put in or grooves for a better fit. Start with position A. If O-ring in position A is too loose in bore, n move O-ring to next groove to right. This will enlarge O-ring slightly for a tighter fit. If it is too tight in bore on position A, n move O-ring to left. Remember to always lubricate O-ring with silicone grease or vaseline before inserting into bore. NOTE: A spare.22 cal. O-ring is provided in O-ring box. 12 GA. 20 GA. O-RING (Do Not Remove) 7 8

6 MUZZE ADAPTER INSTRUCTIONS The Muzzle Adapters use various size O-rings to align boresighter within center of different caliber bores. Refer to O-ring to Caliber Selection Chart (pages 7-8) for proper O-ring. The proper O- ring should enter bore with light to moderate drag when lubricated. The adapter (without screw on extension) is used for all calibers from.22 to 7mm (.284 cal.) O-rings are put in position B as referenced on chart. The screw on adapter is used for all calibers from.308 to.50 caliber. O-rings are put in position A as referenced by chart. The screw on adapter has additional O-ring grooves that are not referenced on chart. These grooves are graduated in size and are provided to compensate for varying tolerance bores & calibers (see pages 7-8). Use se grooves, as required, to insure that O-ring enters bore with proper drag. Always lubricate O-ring with silicone grease or vaseline before inserting into bore. Also, be sure to check bore to make sure that it is clear of any O-rings after boresighting. NOTE: The adapters were conveniently designed so that.308 and.22 caliber O-rings never have to be removed, since se are most popular calibers. The.308 O-ring is used for.30-30,.30-06,.300 Win Mag,.300 WSM,.300 savage,.308 Win. and 7.62mm bores, etc. The.22 caliber O-ring is used for.22,.222,.223, , and 5.56mm bores, etc. The Shotgun Adapter (MA-3) fits 20 GA. and 12 GA. shotgun bores. The 20 GA. O-ring does not have to be removed. The 12 GA. O-ring is put in position C. The or grooves are used to compensate for varying tolerance bores. SR- 100 Scope Reticle eveler The SR-100 converts S-100/150/500 aser Boresighters into an extremely accurate scope reticle leveler. It is designed to precisely level your scope crosshair prior to boresighting. The adapter uses a high quality glass lens and simply slips over laser module housing to change laser spot into a precise laser line. AWAYS MAKE SURE THAT THE FIREARM IS UNOADED PRIOR TO USING ANY BORESIGHTER! 1. Secure rifle in a gun vise and adjust butt of stock so that it is vertical. (Vertical alignment is a preliminary adjustment at this time and does not require precise accuracy) 2. oosen scope rings only until you can start to turn scope. 3. Insert boresighter into muzzle, using correct O-ring. (See Muzzle Adapter Instructions) 4. Slip on SR-100 Adapter and rotate, slightly, until it just contacts boresighter s housing. Do not use any force after contacting housing. 5. Place SR-100 target on a wall between 15 and 25 feet from muzzle and level target with built-in bubble level. (Continued on next page) 9 10

7 6. Turn on laser. Hold boresighter housing and turn adapter until laser line is vertical and aligned with crosshairs on target. Note: You may have to dim 6. Turn on laser. Hold boresighter housing and turn adapter room until lights laser to line see is vertical laser and aligned line, clearly. with crosshairs on target. Note: You may have to dim room lights to see laser line, clearly. 7. Rotate scope & adjust windage to align 7. Rotate crosshair scope with & adjust laser windage line. to (Fig. align 1) crosshair with laser line. (Fig. 1) SR-100 SCOPE EVEING TARGET Fig. 1 SR-100 SCOPE EVEING TARGET Boresighting TIPS The target provided for alternate method is calibrated for a normal scope height of 1.5 above barrel (center to center of scope to bore). For high mounted scopes, you must mark a new elevation line above horizontal dotted line on target to compensate for difference. If your scope is 2.5 center to center, you would mark a line 1.0 above dotted line and adjust your scope elevation to it. Handguns with red dot scopes or lasers, to be sighted-in at close ranges of 25 to 75 feet can be boresighted by placing boresighter laser dot on any object between 25 to 75 feet and aligning red dot scope or laser sight with boresighter laser dot. aser ine 8. Pick up rifle and aim it, using your normal shooting stance. Note position of crosshairs in relation to laser line. If necessary, readjust crosshairs to insure that y are vertical & level in your shooting position. Every shooter holds his firearm in a slightly different position, so it is important to make this check. 8. Pick up rifle and aim it, using your normal shooting stance. Note position of crosshairs in relation to laser line. If necessary, readjust crosshairs to insure that y are vertical & level in your shooting position. Every shooter holds his firearm in a slightly different position, so it is important to make this check. 9. Tighten scope rings, insuring that scope does not move from level position. 10. Proceed with boresighting firearm. 9. Tighten scope rings, insuring that scope does not move from level position. NOTE: Short barreled handguns are not usually compatible with laser boresighters. aser sights on short barrel handguns can be easily aligned by simply aiming at a light surface, 25 feet away, and adjusting laser spot to align with top of front sight. This method is very accurate and does not require use of any boresighter. You can also use this method for red dot sights for up to 75 feet. We unconditionally guarantee that our boresighters are more accurate than any or boresighters. It is important to take your first shots at 25 yards because of many factors affecting boresighting accuracy such as parallax, bullet spin, variable ballistics, etc. You should always sight in your firearm at a range after boresighting to compensate for se factors, regardless of any boresighter you use. 10. Proceed with boresighting firearm

8 SAVS Scope Alignment Verification System Scope Alignment Verification System SAVS The Scope Alignment Verification System (SAVS) Target accurately verifies alignment of your zeroed-in rifle scope after traveling, rough handling or a fall. Your rifle must be zeroed in at a range before using SAVS. 1. Place target 25 feet from muzzle & align laser spot within circle on target. 3. ocate position of center of crosshairs on grid and mark that position with a marker. You now have an accurate reference to check alignment in field. ASER TARGET Rifle Mfg. Serial No. Caliber Zero Distance Bullet Type Wt. (Gr.) Powder Mfg. Wt. (Gr.) Velocity (FPS) You can make a copy of SAVS Target for each rifle and keep it with rifle in your gun case. The Scope Alignment Verification System (SAVS) accurately verifies alignment of your zeroed-in rifle & scope after traveling, rough handling or a fall. Your rifle must be zeroed in at a range before using SAVS. 1. Place target 25 feet from muzzle & align laser spot within circle on target. 3. ocate position of center of crosshairs on grid and mark that position with a marker You now have an accurate reference to check alignment in field. Rifle Mfg. Serial No. Caliber Zero Distance Bullet Type Wt. (Gr.) Powder Mfg. Wt. (Gr.) Velocity (FPS) COPYRIGHT C 2003 Concept Development Corporation 13 14

9 IMPORTANT WARRANTY AND SERVICE INFORMATION The S-100/150/500 Mag aser Boresighters have a ifetime Warranty. Note: Warranty is only valid for original owner. Please register your boresighter at to activate your warranty. For parts, service, or any or technical issues please contact us. Concept Development Corporation E. aser Drive - Fountain Hills, AZ (800) info@con-dev.com