Specifications STANDARD MATERIALS AND FINISHES T6 Aluminum alloy per. Centers Insulator. Performance Data

Transcription

1 ca_0:layout /0/ :5 M Page

2 Micro Metal Shell.050" ontact Spacing MM MM connectors are used in applications requiring highly reliable, extremely small, lightweight connectors with higher density contact configurations than available in traditional rectangular connectors. They are available in 8 shell sizes accommodating from 9 to 00 contacts, and special arrangements of power and coaxial contacts. These connectors are designed to meet the rapidly increasing demands for an environmental, high performance, rugged, moisturesealed microminiature connector. This connector employs size 4 MIROPIN TM /MIROSOKET TM contacts on.050 (.7) centers in a contact density identical to the standard MIRO connector series, but with these additional features: luminum shells to provide greater strength, prevent chipping, cracking or breaking, offer electromagnetic (EMI) and RFI shielding. Silicone elastomer compression interfacial seal to provide a moisture and humidity seal between each contact and between contacts and shell. Specifications STNR MTERILS N FINISHES MEHNIL FETURES Shell 606T6 luminum alloy per oupling Friction/jackscrews QQ00/8, yellow chromate/ Polarization Keystoneshaped shells cadmium, Type II, lass over electroless nickel per SE ontact Spacing.050 (.7) MS6074, lass 4. enters Insulator Liquid rystal Polymer per MILM459, Type GLP0F (900) Glass filled diallyl phthalate per MILM4, Type SGF (7* and 4*4) Shell Styles No. of ontacts Plug and receptacle 9 thru 00 signal; 5 signal/ coaxial; 5 signal/ power; Polyphenylene sulfide per signal/5 coaxial; MILM459, Type GST40F (6*5) signal/5 power; 0 signal/0 coaxial; Polyester per MILM459, Type 0 signal/0 power; GPT0F (0*0) 0 signal/4 coaxial; ontacts Mounting Hardware opper alloy, gold plate 00 Series stainless steel, passivate oaxial able 0 signal/4 power RG 78/U Kit, Jackpost () items 00 Series stainless steel, passivate Wire Size #4 thru # WG Washer Standard Epoxy 400 Series stainless stell, passivate Hysol EE45/H56, color black or Hysol EE498/H56, color green ontact Termination Multiple indent crimp Performance ata The table below summarizes the results of key tests performed in accordance with MILST44, where applicable. ata is applicable to standard connectors with standard termination. Variations may affect this data, so please consult customer service for further information on your requirements. Test ielectric Withstanding Method 00: Voltage 600 V at sea level 50 V at 70,00' altitude Insulation Resistance Method 00 Thermal Shock Method 00. ondition : 55 to +5 Physical Shock Method 004, ondition E: 50 G's, axes, 6 millisecond duration sawtooth pulse Vibration Method 005, ondition IV: 0 G's, 0,000 Hz. hrs urability 500 cycles of mating and unmating, 500 PH max. Moisture Resistance Method 00, Type II, omit steps 7a & 7b Salt Spray Method 00, ondition : 48 hours ontact Resistance Method 00, ondition : (MILST0) t amps t milliamp ontact Retention Per MILTL85 Method riteria of cceptance No breakdown No breakdown 5,000 megohms minimum No physical damage No physical damage No loss of continuity > µsec No physical damage No loss of continuity > µsec No mechanical or electrical defects Insulation resistance > 00 megohms Shall be capable of mating and unmating, and meet contact resistance requirements 8 milliohms maximum 0 milliohms maximum 5 lb. minimum axial load imensions shown in inches (mm) 7

3 Micro Metal Shell.050" ontact Spacing MM How to Order For MILTL85 ordering information see pages 5 and 6. RoHS OMPLINE SERIES ONTT RRNGEMENTS ONTT TYPE TERMINTION TYPE TERMINTION OE HRWRE SHELL FINISH MO OES R MM 5 P H 00 P XXX SERIES MM: (Size 900) Liquid rystal Polymer (LP) MM: (ombo Layout) iallyl Phthalate (P) ONTT TYPE P Pin S Socket TERMINTION TYPE H Harnessinsulated wire. L Soliduninsulated wire. S Solder pot to accept #6 WG harness wire. (Not available with power contact arrangements.) HRWRE M Military specification hardware, see page for military hardware codes. P Jackpost K Jackscrewstandard profile L Jackscrewlow profile F Float mount No hardware standard.09 (.) dia. hole for sizes 95;.0 (.05) dia. hole for size (.8) dia. mounting holes for sizes 95;.66 (4.) dia. hole for size (.75) dia. hole for size 00 (Per MILTL85) TERMINTION OE* (H) 00 8",7/4 strand,#6 WG, MILW6878/4, Type E Teflon, yellow. (H) 00 8", 7/4 strand, #6 WG, MILW6878/4, Type E Teflon, color coded to MILST68 System I. ONTT RRNGEMENTS (standard) 65, 00, 7, 44 (coaxial) or combination of (L) /" uninsulated solid #5 6P5, 0P0, 7P, 4P4 (power) } coax and power WG gold plated copper. (L) " uninsulated solid #5 WG gold plated copper. SHELL FINISH MO OES No Number (Standard cadmium/yellow chromate over nickel 74 Electroless nickel 7 Gold over nickel 4 Irridite/alodine 0 lack anodize *See page 9 for a list of standard termination codes. 8 imensions shown in inches (mm)

4 Micro Metal Shell.050" ontact Spacing MM OTS or Non MilSpec or ommercial or Industrial Standard Wire Termination odes annon Termination ode (Not MS) The following termination codes are listed for your information. For additional codes please refer to ppendix on page 98 to 0. ll wire lengths are minimum. Harness Type (H) n ns a e Type ( ) #6 WG per MILW6878/4, 7/4 strand, type E Teflon, stranded. #5 WG gold plated copper en e r e Ter na n e en (76.) 6 (5.4) 8 (0.) 0 (54.0) (04.8) 8 (457.) 0 (508.0) 4 (609.6) 0 (76.0) 6 (94.4) 48 (9.) 7 (88.8) 0 (048.0) * avity # black H00 H09 H06 H09 H08 H00 H08 H009 H00 H0 H0 H07 H04 H07 H06 H04 H05 H00 H00 H0 H004 H005 H006 H048 H046 H04 L6 L56 L57 L9 L58 L L4 L L7 L6 L6 L0.5 (.8).50 (.8).90 (4.8).50 (6.5).75 (9.5).500 (.70).750 (9.05).000 (5.40).500 (8.0).000 (50.80).500 (6.50).000 (76.0) ontact rrangements (Face View of Pin insert Use Reverse Order for Socket Side) Standard.05 (0.64) TYP..050 (.7) TYP (.09) ontacts ontacts ontacts ontacts ontacts 7 ontacts ontacts ontact identification numbers are for reference only and do not appear on insulator or connector body..0 oaxial.0 (8.) ontacts.74 (8.4).460 (.68) Size 5 Shell Micro contact 5 oax or 5 Power Size 5 Shell 5 Micro contact oax or Power 4 5 Size 5 Shell 0 Micro contacts 4 oax or 4 Power (Not MS).007 (0.8) Size 00 Shell 0 Micro contact 0 oax or 0 Power imensions shown in inches (mm) 9

5 Micro Metal Shell.050" ontact Spacing MM OTS or Non MilSpec or ommercial or Industrial Shell imensions (onforms to MILTL85) Plug G.0 (.79) TWO MTG. HOLES.09 ±.00(. ±0.08) F E.84 (7.).46 (0.57).86 (4.7).09 (.6) REF..00 (5.08) Solder Pot Receptacle G.0 (.79) TWO MTG. HOLES.09 ±.00(. ±0.08) F E.96 (7.5).49 (0.09).09 (.6) REF..00 (5.08).98 (5.0) Solder Pot Receptacle (MM00 only) TWO MTG. HOLES.0 ±.00(.05 ±0.08).49 (0.90).94 (0.0).98 (5.0).09 (.6) REF. G E Pigtail termination F.96 (7.5) Part Number y Shell Size MM9P* MM9S* MM5P* MM5S* MMP* MMP* MM5P* MM5S* MMP* MMS* MM7P* MM7S* MM5P* MM5S* MM00P* MM00S*.785 (9.94).785 (9.94).95 (.75).95 (.75).085 (7.56).085 (7.56).85 (0.0).85 (0.0).5 (.9).5 (.9).485 (7.7).485 (7.7).45 (6.45).45 (6.45).70 (55.).70 (55.).4 (8.48).40 (0.).484 (.9).55 (.97).64 (6.0).70 (7.8).74 (8.64).80 (0.7).884 (.45).95 (4.8).04 (6.6).0 (7.99).984 (4.99).05 (6.7).84 (5.5).508 (8.0) *dd lead type and length; see How To Order. E F +_.005 (0.) G.400 (0.6).400 (0.6).550 (.97).550 (.97).700 (7.78).700 (7.78).800 (0.).800 (0.).950 (4.).950 (4.).00 (7.94).00 (7.94).050 (6.67).050 (6.67).44 (6.6).44 (6.6).0 (7.87).0 (7.87).60 (9.4).60 (9.4).5 (8.9).5 (8.9).94 (0.0).94 (0.0).565 (4.5).565 (4.5).75 (8.6).75 (8.6).865 (.97).865 (.97).965 (4.5).965 (4.5).5 (8.).5 (8.).65 (.).65 (.).5 (0.86).5 (0.86).800 (45.7).800 (45.7).5 (6.4).5 (6.4).5 (6.4).5 (6.4).5 (6.4).5 (6.4).8 (5.79).96 (7.5).7 (6.88).94 (0.0) ***Weight given is /", uninsulated, solid, #5 WG gold plated copper pigtails. Panel Mounting imensions (Sizes 9 00) verage Weights** oz. (gm.) ±5%.06 (.79).06 (.79).084 (.9).08 (.7).05 (.99).04 (.97).9 (.9).8 (.6).40 (.99).9 (.96).6 (4.59).60 (4.56).9 (5.50).88 (5.5).500 (4.).040 (9.5).00 ±.005 (5.08 ±0.).00 ±.005 (7.6 ±0.).95 ±.005 (0.0 ±0.) Plug and Receptacle Rear Mounted Plug and Receptacle Front Mounted Plug Front Mounted Receptacle Rear Mounted 0 imensions shown in inches (mm)

6 Micro Metal Shell.050" ontact Spacing MM Panel utouts NOTE: See page for rear panel mounting configuration. Shell Sizes 9 thru 5 TYP. TYP (.54) +0.) R TYP ±.00 (.4±0.05).00 (0.76) TYP FULL R. (TYP.).05 (0.8)R. (TYP) FULL R. (TYP.) 6 /7 TYP Figure Front Mounting Figure Rear Mounting FULL R. (TYP.) Figure Edgeboard Mounting PNEL REF. Shell Size ( ) (0.8) R. MX (TYP.) ( ) ( ) +0. (45.85 ) ( ) 0.00 FULL R. (TYP.) Figure Front Mounting ( ) (.8 ) ( ) 0.00 FULL R. (TYP.) Figure Rear Mounting ( ) _.00 (.4+_0.05).00 (0.76) TYP. FULL R. (TYP.) ( ) Figure Edgeboard Mounting PNEL REF ( ) 0.00 For 95 Shell Sizes NOTES:. Front panel mounting is the preferred mounting method. Front panel mounting dimensions (figure ) will accommodate either #56 screws or jackpost hardware.. Rear panel mount dimensions (figure ) will accommodate #56 screw hardware only. When mounting the connector with rear panel mount jackpost see the panel cutout dimensions.. Edgeboard mounting bracket (figure ) uses #56 screws. imension.450+/.00 (.4+/0.05) locates the MM receptacle flush with the end of the board. For 00 Shell Size NOTES:. Front mounting is the preferred mounting method. Front panel mounting dimensions (figure ) will accommodate either #440 screws or jackpost hardware.. Rear panel mount dimensions (figure ) will accommodate #440 screw hardware only see the panel cutout dimensions..edgeboard mounting bracket (figure ) uses #440 screws. imension.450+/.00 (.4+/0.05) locates the MM receptacle flush with the end of the board. Shell Size utout Figure imensions shown in inches (mm)

7 Micro Metal Shell.050" ontact Spacing MM Mounting Hardware Views (for sizes 95) This hardware supplied unassembled. LOK SREW RETINING LIP.408 (0.6).8 (4.6).688 (7.48) ONNETOR SHOWN FOR REF. ONLY MTING FE #56 UN PNEL REF..500 (.7) Screw Lock ssembly USHING. (5.89).09 (.6) REOMMENE PNEL THIKNESS #56 UN Jackpost (P) Screw Lock ssembly* *NOTE Torque value is.5 in/lbs max..05 (.) TYP. 90 ngle Mounting racket.096 ±.005 (.44 ± 0.)I..70 (4.).78 ±.005 (4.5 ± 0.) 90 ngle Mounting racket +/.005 (±0.) #56 UN TH escription Screw Lock ssembly Jackpost kit Part Number N/ N/ Mounting racket 90 MM for 9 thru 7 Shell Sizes Mounting racket 90 MM for 5 Shell Size (.7).69 (4.9) NOTES: Screw lock assembly ( ) can be used for front mounting only. Jackpost kit ( ) consists of two assmblies, shipped unassmbled..60 (6.60).50 (8.89) Jackpost ushing (for rear panel mountingfor sizes 95).70 (4.).500 (.7).480 (.9) #56 UN TH Panel Thickness / (.4).087 (.) /6 (.6).056 (.4) /64 (.).04 (.07) / (0.8).05 (0.64) * kit consists of jackpost, nuts, washers. HEX IS.5 (.4)/.5 (.9) ROSS FLTS #56 UN TH MTING FE Jackpost diameter within the "" dimension is.4/.0 (.5/.05). (0.).000 (0.00) Jackpost Kit Number* (.0).5 (.8) I. TYP 7 6 TYP Plug and Receptacle imensions Shell (0.0) Size.000 (0.00) 9.40 (0.9) 5.55 (4.00).70 (7.8) 5.80 (0.4).95 (4.6) 7.0 (7.97) 5.05 (6.70) (0.0).000 (0.00).5 (6.40).5 (6.40).5 (6.40).5 (6.40).5 (6.40).5 (6.40).95 (7.49).05 (.67).00 (.54) R TYP. +_.005 (0.).565 (4.5).75 (8.6).865 (.97).965 (4.5).5 (8.4).65 (.).5 (0.86) imensions shown in inches (mm)

8 Micro Metal Shell.050" ontact Spacing MM Mounting Hardware Views (sizes 95) This hardware is factory installed..04 ±.004 (0.6 ± 0.0) LLOWLE IMETRL FLOT.00 (0.5) LLOWLE XIL FLOT.50 ±.00 (.8 ±.076) MTING FE ONNETOR SHOWN FOR REF. ONLY.490 (.45) MX.75 (8.67) ONNETOR SHOWN FOR REF ONLY HEX HE.050 (.7) ROSS FLTS.050 (.7) EEP (REF).55 (.94) MX.09 (.6) REF..090 ±.005 (.9 ± 0.08)I Float Mount (F).0 ±.00 (0.79 ± 0.08) MTING FE #56 UN PRT HS.040 (.0) MX XIL FLOT Jackscrew (K) Standard Profile MTING FE PRT HS.040 (.0) XIL FLOT #56 UN Jackscrew (L) Low Profile Shown here is a cutaway view of the float mount for the MM connector. The basic shell dimensions are the same for the float mount and the screw mounting hole configurations. View shown is for standard float mount front panel mounting. Reverse mounting is available on request. * NOTE: Torque values are as follows: Low Profile Jackscrew (L).5 inlbs Standard Jackscrew (K).5 inlbs Mounting Hardware to Military Specification (for sizes 9 00) per MILTL85/5 This hardware supplied in kits unassembled ( pieces of each item). #56 UN THRE TYP. PLUG (REF. WITH.09 (.4) I. MOUNTING HOLES.06 (.57) HEX. (REF.) #56 UN THRE TYP. PLUG (REF.) WITH.09 (.4) I. MOUNTING HOLES.6 (9.7).90 (9.9) SIZE 00 ONLY.00 (0.5) TH'K (REF.).00 (0.5) TH'K (REF.) Figure. Jackscrew Low profile Slotted Head Size 95 Size 00* POTTING WELL (REF.) llen head Optional Head onfiguration Plug and Receptacle Low and High Profile Size 95 Size 00* (same dimensions).868 (.05).90 (.9) POTTING WELL (REF.).5 (.8) HEX..87 (4.75) HEX. #56 UN THRE #440 UN THRE LOKWSHER RETINING NUT.54 (.9) HEX..87 (4.75) HEX..06 ±.00 (.57 ± 0.5) SIZE 00 SME Figure. Jackpost ssembly Size 95 Size 00*.90/.85(4.8/4.70).85/.75(4.70/4.44).475 ±.05 (.06 ± 0.64) SIZE 00 SME escription Figure. Jackscrew High Profile Slotted Head Size 95 Size 00* To order hardware kits separately, order either by M85/5** or by 0950XXXX. Size 95 Mod ode Part Number Slotted Head Jackscrew ssy Low Profile (Figure ) M Slotted Head Jackscrew ssy High Profile (Figure ) M llen Head Jackscrew ssy Low Profile (Figure ) M llen Head Jackscrew ssy High Profile (Figure ) M Jackpost ssy (Figure ) M Size 00* * * Mod ode Part Number * * M M M M M *Size 00 requires size mounting holes for MilSpec hardware Note: Torque values as follows: Size inlbs Size inlbs imensions shown in inches (mm)

9 Micro Metal Shell.050" ontact Spacing MM Mounting Hardware Views (for size 00) This hardware supplied unassembled.. ±.005 (. ± 0.) I. #440 UN TH #440 UN TH #4 LOK WSHER PNEL MY E USE WITH.09 (.6) MX THIK PNEL ( ) (.70).95 (0.0) MTING SIE #440 UN NOTHING OR FEMLE TH 90 ngle Mounting racket Jackpost (P).5 ±.005 (5.97 ± 0.).064 ±.00 (.6 ± 0.5) TYP. Note: Size 00 requires.0 dia () mounting hole when using ommercial (P) jackpost kits. 90 ngle Mounting racket escription Jackpost kit Mounting racket 90 MM Part Number ±.005 (0.) N/ (4.85).70 (9.40) This hardware is factory installed..04 ±.004 (0.6 ± 0.0) LLOWLE IMETRL FLOT.00 (0.5) LLOWLE XIL FLOT.74 ±.005 (4.4 ±.0) MTING FE ONNETOR SHOWN FOR REF. ONLY.75 (8.67) HEX. SOKET HE..078 (.98) ROSS FLTS.050 (.7) MIN. EPTH MX.09 (.6) REF. Panel Thickness / (.4) /6 (.6) / (0.8) /64 (.).6 ±.00 (.9 ±.05) I Float Mount (F) Std. (0.).000 (0.00).087 (.).058 (.4).05 (0.64).04 (.07) * jackposts, nuts, washers Jackpost Kit Number* ±.00 (0.79 ± 0.08) ENGGING FE REEPTLE SHOWN FOR REF. ONLY MTING FE #440 UN TH PRT HS.040 (.0) MX XIL FLOT Jackscrew (K) Standard *NOTE: Torque values are as follows: Low Profile Jackscrew (L)4.0 inlbs Standard Profile Jackscrew (K)4.0 inlbs Jackpost ushing (for Rear Panel Mounting) #440 THRE RETINING NUT /6" HEX. LOKING POST #440 UN.70 (4.).500 (.70) R ( ) 0.00 MTING SIE.55 (.94).040 (.0) XIL FLOT #440 UN TH Jackscrew (L) (Low Profile) imensions for Rear Panel Mounting.800 ±.005 (45.7 ± 0.) ( ) ( ) (4.09).59 (4.04) I. Torque value for size 00 Note: Size 00 requires mounting hole shell size when using rear panel mount jackposts 4 imensions shown in inches (mm)

10 Micro Metal Shell.050" ontact Spacing MM onnector Saver Save wear and tear on your equipment and systems connectors by using the "onnector Saver". The multimatings and unmatings experienced by most connectors during testing and final check out can be eliminated. Simply mate the "onnectors Saver" to your unit and use the opposite side for your testing interface...less wear, less tear, less chance of damage. It is available in all eight standard MM layouts. Mating hardware is available and can be ordered either separately or included with the connector saver..040 (.0) LLOWLE XIL FLOT #56 UN TH (95) (TYP.).790 (0.07).5 (8.00) JKSREW/JKPOST USHING (FOR REFERENE ONLY SEE ORERING INFORMTION ELOW.) MIROPIN MIROSOKET ONNETOR REEPT ONNETOR, PLUG KPOTTING, EPOXY INTERFIL SEL.090 (.9) REF. (TYP.).900 (.86) REF. (TYP.) MM Size 9 Shown ERING (TYP.) Size Electroless Nickel (74) Plated admium over Nickel (0) Plated With Hardware W/O Hardware With Hardware W/O Hardware *Hardware Kits MM MM MM MM MM MM MM MM MM MM MM MM98479 MM MM MM MM MM MM MM MM MM MM MM MM MM97947 MM97947 MM97947 MM MM MM MM MM ** ** ** ** ** ** ** *** ±.005 (0.).785 (9.94).95 (.75).085 (7.56).85 (0.0).5 (.9).485 (7.7).45 (6.45).70 (55.).565 (4.5).75 (8.6).865 (.97).965 (4.5).5 (8.).65 (.).5 (0.86).800 (45.7).5 (8.9).94 (0.0) * Kit contains jackpost/jackscrew bushings and ERings. ** Size 95#56 UN Thread *** Size 00#440 UN Thread imensions shown in inches (mm) 5

11 Micro Metal Shell.050" ontact Spacing MILTL85 How to Order MILTL85 Part Number Nomenclature Slash Sheets 9 M85/ 0 H00 * * * * * * SERIES MM M MV Metal Shell, Liquid rystal Polymer (LP) iallyl Phthalate Insulator Polyester Insulator MIL85 SLSH SHEET Plug, onnector, Solderpot Receptacle, onnector, Solderpot Plug, onnector, rimp Type Receptacle, onnector, rimp Type Hardware Only 7 Plug, onnector, Solderpot Receptacle, onnector, Solderpot Plug, onnector, rimp Type Receptacle, onnector, rimp Type Metal Shell Plastic 5 INSERT RRNGEMENT E F G H METL SHELL 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 00 ontact PLSTI 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 5 NOTES: For every Mil Spec Part Number, ITT has one corresponding part number shown an example Tolerance on wire lengths: 8", 6" and 7" long +.00"/0.00".5" and.00" +.00"/.000" 4 For space application, connector shell finish must be "74" and wire must be per MILW759/6. ny deviations to these P/N's will result in assignment of a special P/N, consult factory. 5 Size 00 not available in / 06 through / 09. (Plastic shell) 6 olor coding in accordance with MILST68, System, no parenthesis. See page 0 for color code chart. 7 For mounting hardware to Military Specification (sizes 9 to 00) see page. WIRE TYPE No Number For Solderpot " 6" 8" ".5".0".5".0" 8" 6" 8" 6" 7" 7" 7" 7" SHELL FINISH long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating long. #5 WG, type S per QQW4, Gold Plated long, #5 WG, type S per QQW4, Gold Plated long, #5 WG, type S per QQWW4, Tin Plated long, #5 WG, type S per QQW4, Tin Plated long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 WG per MILW759/69 (all white) long, #6 WG per MILW759/6 olor oded per MILST68, System, 0 colors repeating No number for plastic type connector for admium/yellow chromate over nickel N 74 Electroless Nickel imensions shown in inches (mm)

12 Micro Metal Shell.050" ontact Spacing MILTL85 How to Order MILTL85 Part Number Nomenclature Slash Sheets 07 M85/ 0 * * * SERIES onnector, Electrical, Rectangular, Polarized Shell P oard Mounting MIL85 SLSH SHEET 0 onnector, Plug, ondensed oard Right ngle (R), Sizes 9 7 onnector, Plug, R, Size 5 onnector, Plug, R, Size 00 onnector, Receptacle, R, Sizes onnector, Receptacle, R Size 5 5 onnector, Receptacle, R, Size 00 6 onnector, Plug, oard Right ngle (R), Sizes onnector, Plug, R, Size 5 8 onnector, Plug, R, Size 00 9 onnector, Receptacle, R, Sizes onnector, Receptacle, R Size 5 onnector, Receptacle, R Size 00 onnector, Plug, oard Straight (S), Sizes 9 7 onnector, Plug, S, Size 5 4 onnector, Plug, S, Size 00 5 onnector, Receptacle, S, Sizes onnector, Receptacle, S, Size 5 7 onnector, Receptacle, S Size 00 INSERT RRNGEMENT METL SHELL E F G H 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 00 ontact WIRE TYPE No Number For Solderpot NOTES: 0.09" long, #4 WG solid copper wire per QQW4, Type S, solder dipped For every Mil Spec Part Number, ITT has one 0.40" long, #4 WG solid copper wire per QQW4, Type S, solder dipped corresponding part number 0.7" long, #4 WG solid copper wire per QQW4, Type S, solder dipped Tolerance on wire lengths ±.05 For space application, connector shell finish must be "N". SHELL FINISH 4 ny deviations to these P/N's will result in assignment No letter for plastic type connector of a special P/N, consult customer service. admium / Yellow chromate over nickel N Electroless Nickel HRWRE N No jackpost P Jackpost (permanently attached) T Threaded insert imensions shown in inches (mm) 7